Verification Example Preprocessing Solution Postprocessing Command Line Bicycle Example Preprocessing Solution Postprocessing Command Line

U of A ANSYS Tutorials - Bicycle Space Frame Page 1 of 26
| Verification Example | | Preprocessing | | Solution | | Postprocessing | | Command Line |

| Bicycle Example | | Preprocessing | | Solution | | Postprocessing | | Command Line |
This tutorial was created using ANSYS 7.0 to solve a simple 3D space frame problem.
The problem to be solved in this example is the analysis of a bicycle frame. The problem to be modeled
in this example is a simple bicycle frame shown in the following figure. The frame is to be built of
hollow aluminum tubing having an outside diameter of 25mm and a wall thickness of 2mm.
The first step is to simplify the problem. Whenever you are trying out a new analysis type, you need
something (ie analytical solution or experimental data) to compare the results to. This way you can be
sure that you've gotten the correct analysis type, units, scale factors, etc.
The simplified version that will be used for this problem is that of a cantilever beam shown in the
following figure:
file://D:\ankur\cad\ansya\ANSYST~1\U%20of%20A%20ANSYS%20Tutorials%20-%20Bi... 8/7/2007
1. Give the Simplified Version a Title (such as 'Verification Model').
Utility Menu > File > Change Title
2. Enter Keypoints
For this simple example, these keypoints are the ends of the beam.
We are going to define 2 keypoints for the simplified structure as given in the following
table
coordinate
keypoint
x y z
1 0 0 0
2 500 0 0
From the 'ANSYS Main Menu' select:

Preprocessor > Modeling > Create > Keypoints > In Active CS
3. Form Lines
The two keypoints must now be connected to form a bar using a straight line.
Select: Preprocessor > Modeling> Create > Lines > Lines > Straight Line.
Pick keypoint #1 (i.e. click on it). It will now be marked by a small yellow box.
Now pick keypoint #2. A permanent line will appear.
When you're done, click on 'OK' in the 'Create Straight Line' window.
4. Define the Type of Element
It is now necessary to create elements on this line.
From the Preprocessor Menu, select: Element Type > Add/Edit/Delete.
Click on the 'Add...' button. The following window will appear:
For this example, we will use the 3D elastic straight pipe element as selected in the above
figure. Select the element shown and click 'OK'. You should see 'Type 1 PIPE16' in the
'Element Types' window.
Click on the 'Options...' button in the 'Element Types' dialog box. The following window
will appear:
Click and hold the K6 button (second from the bottom), and select 'Include Output' and
click 'OK'. This gives us extra force and moment output.
Click on 'Close' in the 'Element Types' dialog box and close the 'Element Type' menu.
5. Define Geometric Properties
We now need to specify geometric properties for our elements:
In the Preprocessor menu, select Real Constants > Add/Edit/Delete
Click Add... and select 'Type 1 PIPE16' (actually it is already selected). Click on 'OK'.
Enter the following geometric properties:
Outside diameter OD: 25

Wall thickness TKWALL: 2
This defines an outside pipe diameter of 25mm and a wall thickness of 2mm.
Click on 'OK'.
'Set 1' now appears in the dialog box. Click on 'Close' in the 'Real Constants' window.
6. Element Material Properties
You then need to specify material properties:

In the 'Preprocessor' menu select Material Props > Material Models...
Double click Structural > Linear > Elastic and select 'Isotropic' (double click on it)
Close the 'Define Material Model Behavior' Window.
We are going to give the properties of Aluminum. Enter the following field:
EX 70000
PRXY 0.33
Set these properties and click on 'OK'.
7. Mesh Size
In the Preprocessor menu select Meshing > Size Cntrls > ManualSize > Lines > All Lines
In the size 'SIZE' field, enter the desired element length. For this example we want an
element length of 2cm, therefore, enter '20' (i.e 20mm) and then click 'OK'. Note that we
have not yet meshed the geometry, we have simply defined the element sizes.
(Alternatively, we could enter the number of divisions we want in the line. For an element
length of 2cm, we would enter 25 [ie 25 divisions]).
NOTE
It is not necessary to mesh beam elements to obtain the correct solution. However, meshing is
done in this case so that we can obtain results (ie stress, displacement) at intermediate positions on
the beam.
8. Mesh
Now the frame can be meshed.

In the 'Preprocessor' menu select Meshing > Mesh > Lines and click 'Pick All' in the 'Mesh
Lines' Window
9. Saving Your Work
Utility Menu > File > Save as.... Select the name and location where you want to save your file.
1. Define Analysis Type
From the Solution Menu, select 'Analysis Type > New Analysis'.
Ensure that 'Static' is selected and click 'OK'.
2. Apply Constraints
In the Solution menu, select Define Loads > Apply > Structural > Displacement > On
Keypoints
Select the left end of the rod (Keypoint 1) by clicking on it in the Graphics Window and
click on 'OK' in the 'Apply U,ROT on KPs' window.
This location is fixed which means that all translational and rotational degrees of freedom
(DOFs) are constrained. Therefore, select 'All DOF' by clicking on it and enter '0' in the
Value field and click 'OK'.
3. Apply Loads
As shown in the diagram, there is a vertically downward load of 100N at the end of the bar
In the Structural menu, select Force/Moment > on Keypoints.
Select the second Keypoint (right end of bar) and click 'OK' in the 'Apply F/M' window.
Click on the 'Direction of force/mom' at the top and select FY.
Enter a value of -100 in the 'Force/moment value' box and click 'OK'.
The force will appear in the graphics window as a red arrow.
The applied loads and constraints should now appear as shown below.
4. Solving the System
We now tell ANSYS to find the solution:
Solution > Solve > Current LS
1. Hand Calculations
Now, since the purpose of this exercise was to verify the results - we need to calculate what we
should find.
Deflection:
The maximum deflection occurs at the end of the rod and was found to be 6.2mm as shown above.
Stress:
The maximum stress occurs at the base of the rod and was found to be 64.9MPa as shown above
(pure bending stress).
2. Results Using ANSYS
Deformation
from the Main Menu select General Postproc from the 'ANSYS Main Menu'. In this menu
you will find a variety of options, the two which we will deal with now are 'Plot Results'
and 'List Results'
Select Plot Results > Deformed Shape.
Select 'Def + undef edge' and click 'OK' to view both the deformed and the undeformed
object.
Observe the value of the maximum deflection in the upper left hand corner (shown here
surrounded by a blue border for emphasis). This is identical to that obtained via hand
calculations.
Deflection
For a more detailed version of the deflection of the beam,
From the 'General Postproc' menu select Plot results > Contour Plot > Nodal Solution.
Select 'DOF solution' and 'USUM'. Leave the other selections as the default values. Click
'OK'.
You may want to have a more useful scale, which can be accomplished by going to the
Utility Menu and selecting Plot Controls > Style > Contours > Uniform Contours
The deflection can also be obtained as a list as shown below. General Postproc > List
Results > Nodal Solution ... select 'DOF Solution' and 'ALL DOFs' from the lists in the
'List Nodal Solution' window and click 'OK'. This means that we want to see a listing of all
translational and rotational degrees of freedom from the solution. If we had only wanted to
see the displacements for example, we would have chosen 'ALL Us' instead of 'ALL DOFs'.
Are these results what you expected? Again, the maximum deflection occurs at node 2, the
right end of the rod. Also note that all the rotational and translational degrees of freedom
were constrained to zero at node 1.
If you wanted to save these results to a file, use the mouse to go to the 'File' menu (at the
upper left-hand corner of this list window) and select 'Save as'.
Stresses
For line elements (ie beams, spars, and pipes) you will need to use the Element Table to gain
access to derived data (ie stresses, strains).
From the General Postprocessor menu select Element Table > Define Table...
Click on 'Add...'
As shown above, in the 'Item,Comp' boxes in the above window, select 'Stress' and 'von
Mises SEQV'
Click on 'OK' and close the 'Element Table Data' window.
Plot the Stresses by selecting Plot Elem Table in the Element Table Menu
The following window will appear. Ensure that 'SEQV' is selected and click 'OK'
If you changed the contour intervals for the Displacement plot to "User Specified" you may
need to switch this back to "Auto calculated" to obtain new values for VMIN/VMAX.
Utility Menu > PlotCtrls > Style > Contours > Uniform Contours ...
Again, select more appropriate intervals for the contour plot
List the Stresses

From the 'Element Table' menu, select 'List Elem Table'
From the 'List Element Table Data' window which appears ensure 'SEQV' is
highlighted
Click 'OK'
Note that a maximum stress of 64.914 MPa occurs at the fixed end of the beam as predicted
analytically.
Bending Moment Diagrams
To further verify the simplified model, a bending moment diagram can be created. First, let's look
at how ANSYS defines each element. Pipe 16 has 2 nodes; I and J, as shown in the following
image.
To obtain the bending moment for this element, the Element Table must be used. The Element
Table contains most of the data for the element including the bending moment data for each
element at Node I and Node J. First, we need to obtain obtain the bending moment data.
General Postproc > Element Table > Define Table... . Click 'Add...'.
In the window,
A. Enter IMoment as the 'User label for item' - this will give a name to the data
B. Select 'By sequence num' in the Item box
C. Select 'SMISC' in the first Comp box
D. Enter SMISC,6 in the second Comp box
E. Click 'OK'
This will save all of the bending moment data at the left hand side (I side) of each element.
Now we need to find the bending moment data at the right hand side (J side) of each
element.
Again, click 'Add...' in the 'Element Table Data' window.

A. Enter JMoment as the 'User label for item' - again, this will give a name to the data
B. Same as above
C. Same as above
D. For step D, enter SMISC,12 in the second Comp box
E. Click 'OK'
Click 'Close' in the 'Element Table Data' window and close the 'Element Table' Menu.
Select Plot Results > Contour Plot > Line Elem Res...
From the 'Plot Line-Element Results' window, select 'IMOMENT' from the pull down menu
for LabI, and 'JMOMENT' from the pull down menu for LabJ. Click 'OK'. Note again that
you can modify the intervals for the contour plot.
Now, you can double check these solutions analytically. Note that the line between the I and
J point is a linear interpolation.
Before the explanation of the above steps, enter help pipe16 in the command line as
shown below and then hit enter.
Briefly read the ANSYS documentation which appears, pay particular attention to the
Tables near the end of the document (shown below).
Table 1. PIPE16 Item, Sequence Numbers, and Definitions for the ETABLE
Commands
node I
name item e Definition

MFORX SMISC 1 Member
MFORY SMISC 2 forces at the
MFORZ SMISC 3 node
MMOMX SMISC 4 Member
MMOMY SMISC 5 moments at
MMOMZ SMISC 6 the node
Note that SMISC 6 (which we used to obtain the values at node I) correspond to MMOMZ -
the Member moment for node I. The value of 'e' varies with different Element Types,
therefore you must check the ANSYS Documentation files for each element to determine
the appropriate SMISC corresponding to the plot you wish to generate.
The above example was solved using the Graphical User Interface (or GUI) of ANSYS. This problem
can also been solved using the ANSYS command language interface. To see the benefits of the
command line clear your current file:
From the Utility menu select: File > Clear and Start New
Ensure that 'Read File' is selected then click 'OK'
select 'yes' in the following window.
Copy the following code into the command line, then hit enter. Note that the text following the "!" are
comments.
/PREP7 ! Preprocessor
K,1,0,0,0, ! Keypoint, 1, x, y, z
K,2,500,0,0, ! Keypoint, 2, x, y, z
L,1,2 ! Line from keypoint 1 to 2
!*
ET,1,PIPE16 ! Element Type = pipe 16
KEYOPT,1,6,1 ! This is the changed option to give the extra force and moment outpu
!*
R,1,25,2, ! Real Constant, Material 1, Outside Diameter, Wall thickness
!*
MP,EX,1,70000 ! Material Properties, Young's Modulus, Material 1, 70000 MPa
MP,PRXY,1,0.33 ! Material Properties, Major Poisson's Ratio, Material 1, 0.33
!*
LESIZE,ALL,20 ! Element sizes, all of the lines, 20 mm
LMESH,1 ! Mesh the lines
FINISH ! Exit preprocessor
/SOLU ! Solution
ANTYPE,0 ! The type of analysis (static)
!*
DK,1, ,0, ,0,ALL ! Apply a Displacement to Keypoint 1 to all DOF
FK,2,FY,-100 ! Apply a Force to Keypoint 2 of -100 N in the y direction
/STATUS,SOLU
SOLVE ! Solve the problem
FINISH
Note that you have now finished Postprocessing and the Solution Phase with just these few lines of
code. There are codes to complete the Postprocessing but we will review these later.
Now we will return to the analysis of the bike frame. The steps which you completed in the verification
example will not be explained in great detail, therefore use the verification example as a reference as
required. We will be combining the use of the Graphic User Interface (GUI) with the use of command
lines.
Recall the geometry and dimensions of the bicycle frame:
1. Clear any old ANSYS files and start a new file

Utility Menu > File > Clear and Start New
2. Give the Example a Title

Utility menu > File > Change Title
3. Defining Some Variables
We are going to define the vertices of the frame using variables. These variables represent the
various lengths of the bicycle members. Notice that by using variables like this, it is very easy to
set up a parametric description of your model. This will enable us to quickly redefine the frame
should changes be necessary. The quickest way to enter these variables is via the 'ANSYS Input'
window which was used above to input the command line codes for the verification model. Type
in each of the following lines followed by Enter.
x1 = 500
x2 = 825
y1 = 325
y2 = 400
z1 = 50
4. Enter Keypoints
For this space frame example, these keypoints are the frame vertices.
We are going to define 6 keypoints for this structure as given in the following table (these
keypoints are depicted by the circled numbers in the above figure):
coordinate
keypoint
x y z
1 0 y1 0
2 0 y2 0
3 x1 y2 0
4 x1 0 0
5 x2 0 z1
6 x2 0 -z1
Now instead of using the GUI window we are going to enter code into the 'command line'.
First, open the 'Preprocessor Menu' from the 'ANSYS Main Menu'. The preprocessor menu
has to be open in order for the preprocessor commands to be recognized. Alternatively, you
can type /PREP7 into the command line. The command line format required to enter a
keypoint is as follows:
K, NPT, X, Y, Z
where, each Abbreviation is representative of the following:
Keypoint, Reference number for the keypoint, coords x/y/z
For a more detailed explanation, type help k into the command line
For example, to enter the first keypoint type:
K,1,0,y1,0
into the command line followed by Enter.
As with any programming language, you may need to add comments. The exclamation
mark indicates that anything following it is commented out. ie - for the second keypoint you
might type:
K,2,0,y2,0 ! keypoint, #, x=0, y=y2, z=0
Enter the 4 remaining keypoints (listed in the table above) using the command line
Now you may want to check to ensure that you entered all of the keypoints correctly:
Utility Menu > List > Keypoints > Coordinates only
(Alternatively, type 'KLIST' into the command line)
If there are any keypoints which need to be re-entered, simply re-enter the code. A
previously defined keypoint of the same number will be redefined. However, if there is one
that needs to be deleted simply enter the following code:
KDELE,#
where # corresponds to the number of the keypoint.
In this example, we defined the keypoints by making use of previously defined variables like y1 =
325. This was simply used for convenience. To define keypoint #1, for example, we could have
alternatively used the coordinates x = 0, y = 325, z = 0.
5. Changing Orientation of the Plot
To get a better view of our view of our model, we'll view it in an isometric view:
Select Utility menu bar > PlotCtrls > Pan, Zoom, Rotate...'
In the window that appears (shown left),

you have many controls. Try
experimenting with them. By turning on
the dynamic mode (click on the
checkbox beside 'Dynamic Mode') you
can use the mouse to drag the image,
translating and rotating it on all three
axes.
To get an isometric view, click on

'Iso' (at the top right). You can either
leave the 'Pan, Zoom, Rotate' window
open and move it to an empty area on
the screen, or close it if your screen is
already cluttered.
6. Create Lines
We will be joining the following keypoints together:
keypoint
line Again, we will use the command line to create the lines. The command format to create a
1st 2nd straight line looks like:
1 1 2 L, P1, P2
Line, Keypoint at the beginning of the line, Keypoint at the end of l
2 2 3
3 3 4 For example, to obtain the first line, I would write: ' L,1,2 '
4 1 4 Note: unlike 'Keypoints', 'Lines' will automatically assign themselves the next available
reference number.
5 3 5
6 4 5
7 3 6
8 4 6
Enter the remaining lines until you get a picture like that shown below.
Again, check to ensure that you entered all of the lines correctly: type ' LLIST ' into the
command line
If there are any lines which need to be changed, delete the line by typing the following
code: ' LDELE,# ' where # corresponds to the reference number of the line. (This can be
obtained from the list of lines). And then re-enter the line (note: a new reference number
will be assigned)
You should obtain the following:
7. Define the Type of Element

Preprocessor > Element Type > Add/Edit/Delete > Add
As in the verification model, define the type of element (pipe16). As in the verification model,
don't forget to change Option K6 'Include Output' to obtain extra force and moment output.
8. Define Geometric Properties

Preprocessor > Real Constants > Add/Edit/Delete
Now specify geometric properties for the elements
Outside diameter OD: 25

Wall thickness TKWALL: 2
9. Element Material Properties
To set Young's Modulus and Poisson's ratio, we will again use the command line. (ensure that the
preprocessor menu is still open - if not open it by clicking Preprocessor in the Main Menu)
MP, LAB, MAT, C0

Material Property,Valid material property label, Material Reference Number, valu
To enter the Elastic Modulus (LAB = EX) of 70000 MPa, type: ' MP,EX,1,70000 '
To set Poisson's ratio (PRXY), type ' MP,PRXY,1,0.33 '
10. Mesh Size
As in the verification model, set the element length to 20 mm

Preprocessor > Meshing > Size Cntrls > ManualSize > Lines > All Lines
11. Mesh
Now the frame can be meshed.

In the 'Preprocessor' menu select 'Mesh' > 'Lines' and click 'Pick All' in the 'Mesh Lines'
Window
Saving Your Job

Utility Menu > File > Save as...
Close the 'Preprocessor' menu and open up the 'Solution' menu (from the same 'ANSYS Main Menu').
1. Define Analysis Type

Solution > Analysis Type > New Analysis... > Static
2. Apply Constraints
Once again, we will use the command line. We are going to pin (translational DOFs will be fixed)
the first keypoint and constrain the keypoints corresponding to the rear wheel attachment locations
in both the y and z directions. The following is the command line format to apply constraints at
keypoints.
DK, KPOI, Lab, VALUE, VALUE2, KEXPND, Lab2, Lab3, Lab4, Lab5, Lab6
Displacement on K, K #, DOF label, value, value2, Expansion key, other DOF label
Not all of the fields are required for this example, therefore when entering the code certain fields
will be empty. For example, to pin the first keypoint enter:
DK,1,UX,0,,,UY,UZ
The DOF labels for translation motion are: UX, UY, UZ. Note that the 5th and 6th fields are
empty. These correspond to 'value2' and 'the Expansion key' which are not required for this
constraint. Also note that all three of the translational DOFs were constrained to 0. The DOFs can
only be contrained in 1 command line if the value is the same.
To apply the contraints to Keypoint 5, the command line code is:
DK,5,UY,0,,,UZ
Note that only UY and UZ are contrained to 0. UX is not constrained. Again, note that the 5th and
6th fields are empty because they are not required.
Apply the constraints to the other rear wheel location (Keypoint 6 - UY and UZ).
Now list the constraints ('DKLIST') and verify them against the following:
If you need to delete any of the constraints use the following command: 'DKDELE, K,
Lab' (ie 'DKDELE,1,UZ' would delete the constraint in the 'z' direction for Keypoint 1)
3. Apply Loads
We will apply vertical downward loads of 600N at the seat post location (keypoint 3) and 200N at
the pedal crank location (keypoint 4). We will use the command line to define these loading
conditions.
FK, KPOI, Lab, value, value2

Force loads at keypoints, K #, Force Label directions (FX, FY, FZ), value1, value2 (if r
To apply a force of 600N downward at keypoint 3, the code should look like this: ' FK,3,FY,-
600 '
Apply both the forces and list the forces to ensure they were inputted correctly (FKLIST).
If you need to delete one of the forces, the code looks like this: 'FKDELE, K, Lab' (ie
'FKDELE,3,FY' would delete the force in the 'y' direction for Keypoint 3)
The applied loads and constraints should now appear as shown below.
4. Solving the System

Solution > Solve > Current LS
To begin Postprocessing, open the 'General Postproc' Menu
1. Deformation
Plot Results > Deformed Shape... 'Def + undef edge'
You may want to try plotting this from different angles to get a better idea what's going on
by using the 'Pan-Zoom-Rotate' menu that was earlier outlined.
Try the 'Front' view button (Note that the views of 'Front', 'Left', 'Back', etc depend on how
the object was first defined).
Your screen should look like the plot below:
2. Deflections
Now let's take a look at some actual deflections in the frame. The deflections have been calculated
at the nodes of the model, so the first thing we'll do is plot out the nodes and node numbers, so we
know what node(s) we're after.
Go to Utility menu > PlotCtrls > Numbering... and turn on 'Node numbers'. Turn
everything else off.
Note the node numbers of interest. Of particular interest are those nodes where the
constraints were applied to see if their displacements/rotations were indeed fixed to zero.
Also note the node numbers of the seat and crank locations.
List the Nodal Deflections (Main Menu > General Postproc > List Results > Nodal
Solution...'). Are the displacements and rotations as you expected?
Plot the deflection as well.

General Postproc > Plot Results > (-Contour Plot-) Nodal Solution select 'DOF
solution' and 'USUM' in the window
Don't forget to use more useful intervals.
3. Element Forces
We could also take a look at the forces in the elements in much the same way:
Select 'Element Solution...' from the 'List Results' menu.

Select 'Nodal force data' and 'All forces' from the lists displayed.
Click on 'OK'.
For each element in the model, the force/moment values at each of the two nodes per
element will be displayed.
Close this list window when you are finished browsing.
Then close the 'List Results' menu.
4. Stresses
As shown in the cantilever beam example, use the Element Table to gain access to derived
stresses.
General Postproc > Element Table > Define Table ...

Select 'Add'
Select 'Stress' and 'von Mises'
Element Table > Plot Elem Table
Again, select appropriate intervals for the contour plot
5. Bending Moment Diagrams
As shown previously, the bending moment diagram can be produced.
Select Element Table > Define Table... to define the table (remember SMISC,6 and SMISC,12)
And, Plot Results > Line Elem Res... to plot the data from the Element Table
The above example was solved using a mixture of the Graphical User Interface (or GUI) and the
command language interface of ANSYS. This problem has also been solved using the ANSYS
command language interface that you may want to browse. Open the .HTML version, copy and paste the
code into Notepad or a similar text editor and save it to your computer. Now go to 'File > Read input
from...' and select the file. A .PDF version is also available for printing.
To quit ANSYS, select 'QUIT' from the ANSYS Toolbar or select 'Utility Menu'/'File'/'Exit...'. In the
dialog box that appears, click on 'Save Everything' (assuming that you want to) and then click on 'OK'.

Verification Example Preprocessing Solution Postprocessing Command Line Bicycle Example Preprocessing Solution Postprocessing Command Line

Uploaded by

Copyright:

Available Formats

Verification Example Preprocessing Solution Postprocessing Command Line Bicycle Example Preprocessing Solution Postprocessing Command Line

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Verification Example Preprocessing Solution Postprocessing Command Line Bicycle Example Preprocessing Solution Postprocessing Command Line

Uploaded by

Copyright:

Available Formats

U of A ANSYS Tutorials - Bicycle Space Frame Page 1 of 26

| Verification Example | | Preprocessing | | Solution | | Postprocessing | | Command Line |

1. Give the Simplified Version a Title (such as 'Verification Model').

Utility Menu > File > Change Title

From the 'ANSYS Main Menu' select:

Now pick keypoint #2. A permanent line will appear.

4. Define the Type of Element

It is now necessary to create elements on this line.

From the Preprocessor Menu, select: Element Type > Add/Edit/Delete.

Click on the 'Add...' button. The following window will appear:

5. Define Geometric Properties

We now need to specify geometric properties for our elements:

In the Preprocessor menu, select Real Constants > Add/Edit/Delete

Enter the following geometric properties:

Outside diameter OD: 25

6. Element Material Properties

You then need to specify material properties:

Close the 'Define Material Model Behavior' Window.

Set these properties and click on 'OK'.

Now the frame can be meshed.

9. Saving Your Work

1. Define Analysis Type

Ensure that 'Static' is selected and click 'OK'.

In the Structural menu, select Force/Moment > on Keypoints.

Click on the 'Direction of force/mom' at the top and select FY.

The force will appear in the graphics window as a red arrow.

4. Solving the System

We now tell ANSYS to find the solution:

Solution > Solve > Current LS

2. Results Using ANSYS

Select Plot Results > Deformed Shape.

For a more detailed version of the deflection of the beam,

Click on 'OK' and close the 'Element Table Data' window.

Again, select more appropriate intervals for the contour plot

List the Stresses

Bending Moment Diagrams

Again, click 'Add...' in the 'Element Table Data' window.

name item e Definition

Recall the geometry and dimensions of the bicycle frame:

1. Clear any old ANSYS files and start a new file

2. Give the Example a Title

3. Defining Some Variables

where, each Abbreviation is representative of the following:

Keypoint, Reference number for the keypoint, coords x/y/z

For example, to enter the first keypoint type:

into the command line followed by Enter.

K,2,0,y2,0 ! keypoint, #, x=0, y=y2, z=0

where # corresponds to the number of the keypoint.

5. Changing Orientation of the Plot

In the window that appears (shown left),

To get an isometric view, click on

We will be joining the following keypoints together:

You should obtain the following:

7. Define the Type of Element

8. Define Geometric Properties

Now specify geometric properties for the elements

Outside diameter OD: 25

9. Element Material Properties

MP, LAB, MAT, C0