MIDASIT http://www.midasuser.

com
TEL:1-646-852-9286

MEMBER NAME : C1

1. Calculation Summary
(1) Check Design Parameter
Category Value Criteria Ratio Note
Rebar Ratio ( Min. ) 0.0155 0.0100 0.644 ρmin / ρ
Rebar Ratio ( Max. ) 0.0155 0.0600 0.259 ρ / ρmax

(2) Check Moment Capacity ( Neutral axis )

Category Value Criteria Ratio Note
Moment Capacity ( Dir. X ) ( kN·m ) -53.91 276 0.195 Mux / øMnx
Moment Capacity ( Dir. Y ) ( kN·m ) 20.59 101 0.203 Muy / øMny
Axial Capacity ( kN ) 96.22 490 0.196 Pu / øPn
Moment Capacity ( kN·m ) 57.71 294 0.196 Mu / øMn

(3) Check Shear Capacity

Category Value Criteria Ratio Note
Shear Strength ( Dir. X ) ( kN ) 112 514 0.218 Vux / øVnx
Spacing Limits for Reinforcement ( Dir. X ) ( mm )75.00 113 0.667 sx / sx,max
Shear Strength ( Dir. Y ) ( kN ) 103 514 0.201 Vux / øVnx
Spacing Limits for Reinforcement ( Dir. Y ) ( mm )75.00 113 0.667 sy / sy,max

(4) Check Dimension by Special Provision for Seismic Design

Category Value Criteria Ratio Note
Section Dimension Limit ( mm ) 450 300 0.667 Dimmin,limit / Dimmin
Section Dimension Ratio 1.000 0.400 0.400 Dimratio,min / Dimratio

(5) Check Rebar Limit by Special Provision for Seismic Design

Category Value Criteria Ratio Note
Amount of Transverse Rebar ( Dir. X ) ( mm² ) 226 183 0.809 Ashx,min / Ashx
Amount of Transverse Rebar ( Dir. Y ) ( mm² ) 226 183 0.809 Ashy,min / Ashy

2. Check slenderness ratio

(1) Calculate radii of gyration
rx = 0.3D = 135mm
ry = 0.3B = 135mm
(2) Calculate slenderness ratio
M1x
= 0.000
M2x
M1y
= 0.000
M2y
kx lux M1x
= 14.81 < min(34 + 12 , 40.0) = 34.00 → Not Slender
rx M2x
ky luy M1y
= 14.81 < min(34 + 12 , 40.0) = 34.00 → Not Slender
ry M2y
3. Check Magnified Moment
(1) Calculate moment magnification factor
δns.x = 1.000
δns.y = 1.000

4. Check Minimum Moment

(1) Calculate minimum eccentricity
emin.x = 15 + 0.03D = 28.50mm

2024-01-19 14:43 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : C1

emin.y = 15 + 0.03B = 28.50mm

(2) Calculate minimum moment
Mmin.x = Pu emin.x = 2.742kN·m
Mmin.y = Pu emin.y = 2.742kN·m

5. Check design moment

(1) Calculate design moment
Mc.x = Mux = -53.91kN·m
Mc.y = Muy = 20.59kN·m
Mc = 57.71kN·m

6. Check Design Parameter

Calculation Summary ( Check Design Parameter )
Category Value Criteria Ratio Note
Rebar Ratio ( Min. ) 0.0155 0.0100 0.644 ρmin / ρ
Rebar Ratio ( Max. ) 0.0155 0.0600 0.259 ρ / ρmax

Rebar Ratio ( Min. ) 0.64

Rebar Ratio ( Max. ) 0.26

0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50
(1) Calculate rebar ratio
Ag = 202,500mm², Ast = 3,142mm²
ρmin = 0.0100, ρmax = 0.0600, ρ = 0.0155
ρmin < ρ < ρmax → O.K
(2) Calculate eccentricity
ex = Mc.y / Pu = 214mm
ey = Mc.x / Pu = 560mm
e = Mc / Pu = 600mm
Rotation angle of neutral axis = 20.90°
(3) Calculate concentric axial load capacity
P0 = 0.85f'c ( Ag - Ast ) + fy Ast = 6,049kN
P0.max = 0.80P0 = 4,839kN
Pt = fy Ast = -1,304kN

7. Check Moment Capacity ( Balanced axis )

(1) Calculate capacity of compression stress block
β1 = 0.850
c = 313mm, a = β1 ㆍ c = 266mm
Acom = 89,441mm²
ccx = 32.42mm, ccy = 119mm
Cc = 0.85 ㆍ f'c ㆍ Acom = 2,129kN
Mnx = Cc ㆍ ccy = 254kN·m
Mny = Cc ㆍ ccx = 69.02kN·m
(2) Calculate capacity of rebar
ds fs As Fs dy Mnx dx Mny
i εs
(mm) (MPa) (mm²) (kN) (mm) (kN) (mm) (kN)
1 529 -0.002075 -415 314 -130 -185 24.12 -185 24.12
2 356 -0.000418 -83.57 314 -26.26 0.000 0.000 -185 4.858
3 184 0.001239 248 314 77.88 185 14.41 -185 -14.41
4 140 0.001661 332 314 104 185 19.31 -61.67 -6.437
5 95.64 0.002083 415 314 130 185 24.12 61.67 8.041
6 51.64 0.002505 415 314 130 185 24.12 185 24.12
7 224 0.000848 170 314 53.27 0.000 0.000 185 9.855

2024-01-19 14:43 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : C1

8 397 -0.000809 -162 314 -50.86 -185 9.409 185 -9.409

9 441 -0.001231 -246 314 -77.37 -185 14.31 61.67 -4.771
10 485 -0.001653 -331 314 -104 -185 19.22 -61.67 6.406

∑Fs = 108kN
∑Mnx = 149kN·m
∑Mny = 42.38kN·m
(3) Calculate nominal capacity for neutral axis
Pb = Cc + Ps = 2,236kN
Mnx = Mnx.conc + Mnx.bar = 403kN·m
Mny = Mny.conc + Mny.bar = 111kN·m
Mn = ( Mnx )2 + ( Mny )2 = 418kN·m

8. Check Moment Capacity ( Neutral axis )

Calculation Summary ( Check Moment Capacity ( Neutral axis ) )
Category Value Criteria Ratio Note
Moment Capacity ( Dir. X ) ( kN·m ) -53.91 276 0.195 Mux / øMnx
Moment Capacity ( Dir. Y ) ( kN·m ) 20.59 101 0.203 Muy / øMny
Axial Capacity ( kN ) 96.22 490 0.196 Pu / øPn
Moment Capacity ( kN·m ) 57.71 294 0.196 Mu / øMn

Moment Capacity ( Dir. X ) 0.20

Moment Capacity ( Dir. Y ) 0.20

Axial Capacity 0.20

Moment Capacity 0.20

0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50
(1) Calculate capacity of compression stress block
c = 191mm, a = β1 ㆍ c = 163mm
Acom = 39,731mm²
ccx = 72.99mm, ccy = 167mm
Cc = 0.85 ㆍ fck ㆍ Acom = 946kN
Mnx = Cc ㆍ ccy = 158kN·m
Mny = Cc ㆍ ccx = 69.02kN·m
(2) Calculate capacity of rebar
ds fs As Fs dy Mnx dx Mny
i εs
(mm) (MPa) (mm²) (kN) (mm) (kN) (mm) (kN)
1 529 -0.005293 -415 314 -130 -185 24.12 -185 24.12
2 356 -0.002585 -415 314 -130 0.000 0.000 -185 24.12
3 184 0.000123 24.56 314 7.715 185 1.427 -185 -1.427
4 140 0.000812 162 314 51.04 185 9.442 -61.67 -3.147
5 95.64 0.001502 300 314 94.36 185 17.46 61.67 5.819
6 51.64 0.002191 415 314 130 185 24.12 185 24.12
7 224 -0.000517 -103 314 -32.49 0.000 0.000 185 -6.010
8 397 -0.003225 -415 314 -130 -185 24.12 185 -24.12
9 441 -0.003914 -415 314 -130 -185 24.12 61.67 -8.041
10 485 -0.004604 -415 314 -130 -185 24.12 -61.67 8.041

∑Fs = -401kN
∑Mnx = 149kN·m
∑Mny = 43.48kN·m
(3) Calculate nominal capacity for neutral axis
Pn = Cc + Ps = 545kN

2024-01-19 14:43 3
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : C1

Mnx = Mnx.conc + Mnx.bar = 307kN·m

Mny = Mny.conc + Mny.bar = 112kN·m
Mn = ( Mnx )2 + ( Mny )2 = 327kN·m
(4) Calculate strength reduction factor
εt.min = 0.0026, εt.max = 0.0050
εt = 0.002370
ø = 0.650
(5) Calculate axial load and moment capacities
øPn = 490kN
øMnx = 276kN·m
øMny = 101kN·m
øMn = 294kN·m
Mux / øMnx = 0.195 < 1.000 → O.K
Muy / øMny = 0.203 < 1.000 → O.K
Pu / øPn = 0.196 < 1.000 → O.K
Mc / øMn = 0.196 < 1.000 → O.K

P (kN)
6250
θ=20.14˚
N.A=20.90˚
5475

4700

3925

3145
3150

2375
eb=312.88mm

1600

825
(490,294)
(96,58) M (kN·m)
050

-725

-1500
0
45

90

135

180

225

270

315

360

405

450

9. Calculate Shear Force by Special Provisions for Seismic Design (Direction Y).
(1) Calculate bending strength for design shear force.
ø = 1.000
Mprx,I.CW = 0.000kN·m
Mprx,J.CW = 414kN·m
Mprx,I.CCW = 0.000kN·m
Mprx,J.CCW = 414kN·m
(2) Calculate design shear force by special provision for seismic design
Vey1 = (Mprx,I.CW + Mprx,J.CW )/Lny = 103kN
Vey2 = (Mprx,I.CCW + Mprx,J.CCW )/Lny = 103kN
Vey = max(Vey1 , Vey2 ) = 103kN

10. Calculate Shear Force by Special Provisions for Seismic Design (Direction X).
(1) Calculate bending strength for design shear force.
2024-01-19 14:43 4
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : C1

ø = 1.000
Mpry,I.CW = 0.000kN·m
Mpry,J.CW = 448kN·m
Mpry,I.CCW = 0.000kN·m
Mpry,J.CCW = 448kN·m
(2) Calculate design shear force by special provision for seismic design
Vex1 = (Mpry,I.CW + Mpry,J.CW )/Lnx = 112kN
Vex2 = (Mpry,I.CCW + Mpry,J.CCW )/Lnx = 112kN
Vex = max(Vex1 , Vex2 ) = 112kN

11. Check Shear Capacity

Calculation Summary ( Check Shear Capacity )
Category Value Criteria Ratio Note
Shear Strength ( Dir. X ) ( kN ) 112 514 0.218 Vux / øVnx
Spacing Limits for Reinforcement ( Dir. X ) ( mm )75.00 113 0.667 sx / sx,max
Shear Strength ( Dir. Y ) ( kN ) 103 514 0.201 Vux / øVnx
Spacing Limits for Reinforcement ( Dir. Y ) ( mm )75.00 113 0.667 sy / sy,max

Shear Strength ( Dir. X ) 0.22

Spacing Limits for Reinforcement ( Dir. X ) 0.67

Shear Strength ( Dir. Y ) 0.20

Spacing Limits for Reinforcement ( Dir. Y ) 0.67

0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50
(1) Calculate maximum space
ø = 0.750
hx = 207mm
Smax1 = min[6DMainBar , 0.25B, 0.25D, 150] = 113mm
Smax2 = 100 + (350-hx )/3 = 148mm
Smax = min(Smax1 , Smax2 ) = 113mm
(2) Calculate Shear Strength (Direction X)
s = 75.00mm < smax = 113mm → O.K
Nu
øVc = ø0.17 (1+ ) f'c bw d = 129kN
14Ag
Av fyt d
øVs = ø = 385kN
s
øVn = øVc + øVs = 514kN
Vu / øVn = 0.218 → O.K
(3) Calculate Shear Strength (Direction Y)
s = 75.00mm < smax = 113mm → O.K
Nu
øVc = ø0.17 (1+ ) f'c bw d = 129kN
14Ag
Av fyt d
øVs = ø = 385kN
s
øVn = øVc + øVs = 514kN
Vu / øVn = 0.201 → O.K

12. Check Dimension by Special Provision for Seismic Design

Calculation Summary ( Check Dimension by Special Provision for Seismic Design )
Category Value Criteria Ratio Note
Section Dimension Limit ( mm ) 450 300 0.667 Dimmin,limit / Dimmin
Section Dimension Ratio 1.000 0.400 0.400 Dimratio,min / Dimratio

2024-01-19 14:43 5
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : C1

Section Dimension Limit 0.67

Section Dimension Ratio 0.40

0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50
(1) Calculate section dimension limit
Dimmin,limit = 300mm
Dimmin = 450mm
Dmin > Dmin,limit → O.K
(2) Calculate section dimension ratio
Dimratio,min = 0.400
Dimratio = 1.000
Dimratio > Dimratio,min → O.K

13. Check Rebar Limit by Special Provision for Seismic Design

Calculation Summary ( Check Rebar Limit by Special Provision for Seismic Design )
Category Value Criteria Ratio Note
Amount of Transverse Rebar ( Dir. X ) ( mm² ) 226 183 0.809 Ashx,min / Ashx
Amount of Transverse Rebar ( Dir. Y ) ( mm² ) 226 183 0.809 Ashy,min / Ashy

Amount of Transverse Rebar ( Dir. X ) 0.81

Amount of Transverse Rebar ( Dir. Y ) 0.81

0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50
(1) Calculate amount of transverse rebar (Direction X)
sbc f'c Ag
Ash,min1 = 0.3 (( )-1 ) = 111mm²
fyt Ach
sbc f'c
Ash,min2 = 0.09 = 183mm²
fyt
Ash,min = max (Ash,min1 Ash,min2 ) = 183mm²
Ashx = 226mm² > Ashx,min = 183mm² → O.K
(2) Calculate amount of transverse rebar (Direction Y)
sbc f'c Ag
Ash,min1 = 0.3 (( )-1 ) = 111mm²
fyt Ach
sbc f'c
Ash,min2 = 0.09 = 183mm²
fyt
Ash,min = max (Ash,min1 Ash,min2 ) = 183mm²
Ashy = 226mm² > Ashy,min = 183mm² → O.K

2024-01-19 14:43 6