SCHOOLS

YEAR 12 MOCK 2 UNIFIED EXAMINATION

2021/2022 ACADEMIC SESSION
SUBJECT: TECHNICAL DRAWING (OBJECTIVE & GEOMETRY)
TIME: 1HOUR
PAPER 1
INSTRUCTIONS
This paper consists of two sections A and B. Each question under section A (PAPER 1) is
followed by four lettered A-D. Find the correct option for each question and shade in pencil
on your answer sheet, the answer space which bears the same letter as the option you have
chosen. Give only one answer to each question. Answer section B (PAPER 2) in your answer
booklet/drawing sheet.
SECTION A: OBJECTIVE TEST
INSTRUCTION: Answer all questions from this part.
1. A thin long chain line is used to indicate 5. A right cone can be developed by using
A. Breaks ________
B. Centres A. Parallel lines only
C. Constructions B. Radial and parallel lines
D. Dimension C. Radial lines only
2. The reflector of a car headlamp is an D. Triangulation and radial lines
application of a/an
A. Ellipse
B. Epicycloids
C. Hyperbola
D. Parabola 6. What type of washer is shown above?
3. Which of the loci below is defined as a point A. Circular
moving so as to be equidistant from a fixed B. Flat
point from a fixed line? C. Square
A. Hyperbola D. Tab
B. parabola
C. ellipse
D. circle
4. The locus of a point which moves uniformly 7. Parts X and Y in the metric thread drawn above
along a straight line as the line rotates at are ……….. and ………………..
constant speed about a fixed point is called A. Pitch, crest
A. Involute B. Pitch, root
B. Archimedean spiral C. Root, crest
C. inferior trochoids D. Tip, root
D. helix 8. When a closed square pyramid is developed,
how many faces are obtained?
A. Four
B. Five
C. Six
D. Seven
1|Page
9. In orthographic projection, elevations are
drawn on the. I. Vertical plane II. Horizontal
III. Auxiliary plane.
A. I only 15. The electrical symbol above represents a
B. I and II only A. Transistor
C. II and III only B. Lamp
D. I, II and III C. d. c. motor
10. A tangent to a circle intersects its normal at an D. a. c. motor
angle. 16. Which of the following pairs of polygons
A. 30° contains 45o and 60o exterior angles
B. 45° respectively?
C. 60° A. Pentagon and Octagon
D. 90° B. Heptagon and Hexagon
11. Diagonal scale are used to measure up to. C. Octagon and Hexagon
A. One decimal place D. Pentagon and decagon
B. Two decimal place
C. Three decimal place
D. Four decimal place

17. The elevation in the direction of arrow F. of the

block above is

Used the figure above to answer question 12 and 13

12. The scale shown in the figure above is called
A. Plain scale
B. Scale of chord
C. Diagonal Scale
D. Isometric scale
13. The distance Q on the scale is
A. 1.50mm
B. 15.0mm
C. 15.5mm
D. 155.0mm

18. The purpose of the construction above is to

14. In the construction of the helix above the length A. Escribe the triangle
H is the B. Circumscribe a circle
A. Width C. Inscribe a circle
B. Lead D. Divide the triangle.
C. Minor diameter
D. Major diameter
2|Page
 24. Auxiliary view are used to draw all the
The figure below shows different cutting planes following except
through a cone. Use it to answer questions 19 and 20 A. traces of line on planes
B. trace of reduction on planes
C. true shape of surfaces
D. true length of lines
25. The diagonal of a rhombus bisect each other at
A. 30°
B. 45°
C. 60°
19. Which of the cutting planes shown on the cone D. 90°
will produce a parabola?
A. F–F
B. X–X
C. P–P
D. Q –Q
20. Which of the cutting planes shown on the cone 26. What is the value of angle QRT in the figure
will produce a hyperbola? above?
A. F –F A. 135o
B. X – X B. 105o
C. P – P C. 75o
D. Q –Q D. 60o
21. When a line passes through a plane, the point of 27. When a line passes through a plane, the point of
intersection is called intersection is called
A. Projection A. Projection
B. Trace B. Trace
C. Reference line C. Reference line
D. True length. D. True length.
28. Which of the following drawing instruments is
used with a T-square to draw a perpendicular
line?
22. The figure above shows the development of a A. Dividers
truncated B. Compass
A. Pentagonal prism C. Protractor
B. Octagonal prism D. Set square
C. Hexagonal prism 29. If a length 1.0 metre on land is represented by
D. Decagonal prism 4.0cm on a drawing, the scale used is
A. 1:20
B. 1:25
C. 1:40
D. 1:50
30. A circular object in isometric view is shown by
drawing a/an
A. Ellipse
23. The figure above shows the development of a/an B. Parabola
A. Closed square prism C. Sphere
B. Open rectangular prism D. Hyperbola
C. Open square prism
D. Closed rectangular prism
3|Page
 BUILDING DRAWING
31. Which of the following tools is
classified under impelling tools?
A. Plane
B. Hammer
36. The material conventional
C. Chisel representation shown in the figure
D. Saw above is
A. Glass
B. Concrete
C. Wool
D. Water
Used the sketch of a roof above to answer
questions 32 and 33.

32. Which of the labeled parts is the ridge?

A. J
B. H 37. The tool shown in the freehand sketch
C. G above is called
D. F A. wooden hawk
33. The part labeled K shows the B. bolster
A. Plate C. rammer
B. Tie D. wooden float
C. Collar
D. Rafter
34. Which of the following is pitched at
one side only?
A. Hipped roof
B. Shed roof 38. The building tool show above is called
C. Butterfly roof A. builder square
D. Gabble roof B. spirit level
35. Which of the following is NOT part of C. trowel
a building foundation? D. steel rules
A. Hardcore 39. The primary function of the internal
B. Earthfilling walls of building is to
C. DPC A. Carry load
D. Skirting B. divide spaces
C. reinforce building
D. reinforce foundation
40. Which of the building part listed below
is found on a staircase?
A. Eave
B. Sill
C. Jamb
D. Tread

4|Page
 MECHANICAL DRAWING
41. Which of the following is not a type of
section?
A. Recess
B. offset
C. revolved
D. removed

46. What type of key is illustrated above?

A. Parallel
B. Gib
C. Woodruff
Use the figure above to answer questions 42 D. Saddle
and 43.
42. The part labeled X in the assembly
above is a
A. Pin
B. Bush 47. The figure above shows the convention
C. Bolt for representing a
D. Lock nut A. tension spring
43. The part labeled Y is a B. compression spring
A. Collar C. Torsion spring
D. leaf spring
B. Pin
C. Bolt
D. Washer
44. A thread designated as M6 x 0.75
implies
A. 6mm root diameter and 0.75mm
crest
The figure above shows part of a machine
B. 6mm root diameter and 0.75mm assembly. Use it to answer questions 48
pitch and 49.
C. 6o thread angle and 0.75mm pitch 48. The two views represent a
D. 6mm length angle and 0.75mm crest A. Pipe
B. Screw
C. Stud
D. Shaft
49. The part labelled Y in the assembly is
a
A. saddle key
B. gib head key
45. The figure above shows the schematic C. feather key
representation of a D. parallel key
A. Compression spring 50. The construction of a bolt is started
B. Tension spring with the
C. Torsion spring A. regular hexagon
D. Leaf spring B. chamfer curve
C. threaded length
D. nominal diameter

5|Page
 SCHOOLS
YEAR 12 MOCK 2 UNIFIED EXAMINATION
2021/2022 ACADEMIC SESSION
SUBJECT: TECHNICAL DRAWING (OBJECTIVE & GEOMETRY)
TIME: 1HOUR: 30MINS
SECTION B (GEOMETRY)
[60 marks]
READ THE FOLLOWING INSTRUCTIONS
i. Answer three questions only. Each questions carries equal marks.
ii. Strictly geometrical methods are to be used. Lines that are parallel, perpendicular or
inclined at angles of 30o, 45o or 60o to other lines may be drawn without construction
lines being shown. All other construction lines must be shown clearly. Accuracy and
good draughtsmanship are essential.
iii. ALL dimensions are in millimetres except otherwise stated.

1. Two views of a bracket in a machine are shown in first angle projection above. Draw the
bracket in isometric, making point X the lowest.

2. The figure above is a lever mechanism in a lifting device. Draw the lever full size and
show all points of tangency and the construction lines.

6|Page
3. Two views of a triangular lamina PQR are shown in the figure above. Copy the given
viewsand determine
a. (i) the true shape of the lamina
(ii) angle to the horizontal plane
b. Measure and state the lengths of its sides

4. The figure above shows a bracket. Draw full size, in first angle orthographic projection the
following views:

a. front elevation in the direction of arrow X.

b. plan
c. left end elevation

7|Page
 5a. The figure above shows the sheet metal fitting in the metalwork workshop.
Develop the full pattern of the sheet metal.

b. Construct a square and a heptagon on a common base of 40mm.

8|Page