Hitachi Proprietary DKC810I

Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.

INST00-00

INSTALLATION SECTION

INST00-00
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST00-10

Contents

INST01-10 1. Storage system Configuration Outline

INST01-10 1.1 General Information
INST01-10 1.1.1 Model List
INST01-90 1.1.2 Configuration
INST01-90 1.1.2.1 Controller Chassis Configuration
INST01-120 1.1.2.2 Cache Memory Upgrade Table
INST01-380 1.1.2.3 System Configurations and RAID Group Installation Order
INST01-380 1.1.2.3.1 Rough time of installation
INST01-390 1.1.2.3.2 System Configurations
INST01-490 1.1.2.3.3 Connection of DKA to Drive Chassis
INST01-540 1.1.2.3.4 System Configurations and Numbers of Options
Required
INST01-640 1.1.2.3.5 RAID Group Installation Order
INST01-670 1.1.2.4 Notes for Installing Flash Drives
INST01-670 1.1.2.5 Notes for Installing Flash Module Drive Chassis
INST01-680 1.1.3 Specifications
INST01-710 1.1.4 Environmental Specifications
INST01-720 1.1.5 Power requirement
INST01-730 1.1.6 Service Clearance and Floor Cutout
INST01-930 1.1.7 Dimensions
INST01-960 1.1.8 Facility grounding check

INST00-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST00-20

INST02-10 2. Installation and De-installation procedure

INST02-10 2.1 New Installation Procedure Table
INST02-40 2.2 Non-Disruptive Installation Procedure Table
INST02-70 2.3 Non-Disruptive De-installation Procedure Table
INST02-90 2.4 Disruptive Installation Procedure Table
INST02-100 2.5 Disruptive De-installation Procedure Table
INST02-110 2.6 Trouble shooting for errors in install SVP procedure
INST02-110 2.6.1 ECC group + LDEV
INST02-130 2.6.2 DKA
INST02-140 2.6.3 Number of Channel
INST02-150 2.6.4 Cache Capacity
INST02-170 2.6.5 MPB + Module
INST02-190 2.6.6 SVP
INST02-200 2.7 Trouble shooting for errors in remove SVP procedure
INST02-200 2.7.1 ECC group + LDEV
INST02-210 2.7.2 DKA
INST02-220 2.7.3 Number of Channel
INST02-230 2.7.4 Cache Capacity
INST02-240 2.7.5 MPB + Module
INST02-250 2.7.6 SVP
INST02-260 2.8 Availability of Installation and De-installation
INST02-300 2.9 New Installation procedures without the pre-installation at a customer site
INST02-300 2.9.1 Application
INST02-310 2.9.2 Conditions to use these procedures
INST02-320 2.9.3 Procedures
INST02-420 2.10 Obstacle part replacement procedure in install
INST02-420 2.10.1 Replacement procedure when PCB could not be restoring
INST02-440 2.11 Trouble shooting at the time of new installation

INST00-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST00-30

INST03-01-10 3. Hardware Installation

INST03-01-10 3.1 Common Item of Installation and De-Installation
INST03-01-10 3.1.1 Bezel Opening-Closing Procedure
INST03-01-70 3.1.2 Attaching the Wrist Strap
INST03-01-80 3.1.3 Notes when installing or removing the part
INST03-01-80 3.1.3.1 Notes when handling the PCB
INST03-01-100 3.1.4 About the storage media used for installation / maintenance
process
INST03-01-110 3.1.5 Maintenance PC(Console PC)
INST03-01-110 3.1.5.1 Specifications for the Maintenance PC
INST03-01-120 3.1.5.2 Installation Location of Maintenance PC
INST03-01-130 3.1.5.3 Attachment / Removal Procedure of Maintenance PC
INST03-01-180 3.1.6 Notes when connecting the DEV interface cable
INST03-01-190 3.1.7 Notes when connecting and disconnecting MFC cable
INST03-02-10 3.2 UNPACKING AND INSPECTION
INST03-02-20 3.2.1 Unpacking
INST03-03-10 3.3 Installation of Rack and Side Cover
(DKC-F810I-RK42/SCOV/SCOVH)
INST03-03-50 3.3.1 Installation Procedure of Rack and Side Cover
INST03-04-10 3.4 Installation of Controller Chassis
(DKC810I-CBXA, DKC-F810I-CBXB/CRF42/CRF3R/BCH/BCP)
INST03-04-50 3.4.1 Installation Procedure of Controller Chassis
INST03-04-210 3.4.2 Installation Procedure of Bezel
INST03-05-10 3.5 Installation of Drive Chassis
(DKC-F810I-UBX/SBX/FBX/SBBRAL/BUH/BUP/FMDRAL/BFH/BFP)
INST03-05-10 3.5.1 Rough time of installation
INST03-05-20 3.5.2 Parts List
INST03-05-70 3.5.3 IInstallation Procedure of Drive Chassis
(DKC-F810I-UBX/SBX)
INST03-05-430 3.5.4 Installation Procedure of FMD Chassis (DKC-F810I-FBX)
INST03-06-10 3.6 Installation of Power Cord Kit (DKC-F810I-PLUC/PHUC/PFUC/PLEC/
PHEC/PHEC/PLCC/PHCC/PFCC)
INST03-06-10 3.6.1 Installation of DKC Power Cord Kit
(DKC-F810I-PLUC/PLEC/PLCC)
INST03-06-90 3.6.2 Installation of DKU Power Cord Kit
(DKC-F810I-PHUC/PHEC/PHCC)
INST03-06-200 3.6.3 Installation of DKU (FBX) Power Cord Kit
(DKC-F810I-PFUC/PFEC/PFCC)

INST00-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST00-40

INST03-07-10 3.7 Installation of Processor Blade, HUB, Cache Memory, Cache Backup
Module kit and Cache Flash Memory, Inter-Controller Connecting Kit
and Inter-Controller Connecting Cable
(DKC-F810I-MP/HUB/CM16G/CM32G/CPEX/BKMS/BKML/BMM128/
BMM256/MOD5/MOD30/MOD1J/MFC5/MFC30/MFC1J)
INST03-07-50 3.7.1 Installation of Module (DKC-F810I-MP/HUB/CM16G/CM32G/
CPEX/BKMS/BKML/BMM128/BMM256/MOD5/MOD30/
MOD1J/MFC5/MFC30/MFC1J)
INST03-07A-10 3.7.2 Installation of Processor Blade, HUB (DKC-F810I-MP/HUB)
INST03-08A-10 3.8 Installation of Channel Adapter
INST03-08A-10 3.8.1 Installation of Fibre 8/16-port 8/16G Host Adapter
(DKC-F810I-16FC8/8FC16)
INST03-08B-10 3.8.2 Installation of Mainframe Fibre 16-port 8G Host Adapter
(DKC-F810I-16MS8/16ML8)
INST03-09-10 3.9 Changing of SFP (DKC-F810I-1PL8/1PS8/1PL16/1PS16)
INST03-10-10 3.10 Installation of Cache Memory, Cache Backup Module kit, Cache
Flash Memory and Inter-Controller Connecting Cable
(DKC-F810I-CM16G/CM32G/CPEX/BKMS/BKML/BMM128/BMM256/
MFC5/MFC30/MFC1J)
INST03-11-10 3.11 Installation of Disk Adapter, Drive and DEV Interface Cable
(DKC-F810I-SCA/CC1/CC2/CC4/300KCM/600JCM/900JCM/
1R2JCM/3R0H3M/4R0H3M/400MCM/800MCM/1R6FM/3R2FM)
INST03-11-50 3.11.1 Flowchart
INST03-11A-10 3.11.2 When performing addition of the data/spare Drive
(DKC-F810I-300KCM/600JCM/900JCM/1R2JCM/3R0H3M/
4R0H3M/400MCM/800MCM/1R6FM/3R2FM)
INST03-11B-10 3.11.3 When performing addition of the DKA and Device Interface
Cable (DKC-F810I-SCA/CC1/CC2)
INST03-11C-10 3.11.4 When performing addition of the data/spare Drive and Device
Interface Cable that accompanies the addition of the DKU
(DKC-F810I-CC1/CC2/CC4/300KCM/600JCM/900JCM/
1R2JCM/3R0H3M/4R0H3M/400MCM/800MCM/1R6FM/3R2FM)
INST03-11C-20 3.11.4.1 Storage system Configurations and Required I/F Cable
Options
INST03-11C-120 3.11.4.2 Attachment of Location Labels for Device Interface Cable
(DKC-F810I-CC1/CC2/CC4)
INST03-11C-150 3.11.4.3 Setting up the New Device Structure Information
INST03-11C-340 3.11.4.4 Installation Procedure of drive
INST03-11C-910 3.11.4.5 Installation Procedure of Device Interface Cable CC1
(DKC-F810I-CC1)
INST03-11C-960 3.11.4.6 Installation Procedure of Device Interface Cable CC2
(DKC-F810I-CC2)
INST03-11C-1140 3.11.4.7 Installation Procedure of Device Interface Cable CC4
(DKC-F810I-CC4)
INST03-11C-1440 3.11.4.8 SVP post procedure
INST00-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST00-50

INST03-11D-10 3.11.5 When performing addition of the DKA and DEV interface cable
that accompanies the addition of the DKU-00/10
(only hardware procedure) (DKC-F810I-SCA/CC1/CC2)
INST03-11D-10 3.11.5.1 In the case of Standard Model
INST03-11D-220 3.11.5.2 In the case of High-performance Model
INST03-12-10 3.12 Installation of Service Processor (DKC-F810I-SVP)
INST03-12-30 3.12.1 Installation Procedure of Service Processor (DKC-F810I-SVP)
INST03-12-30 3.12.1.1 Installation Procedure
INST03-12-610 3.12.1.2 Confirmation Procedure
INST03-13-10 3.13 Installation of Filler Panel (DKC-F810I-FIHT)
INST03-13-20 3.13.1 Installation Procedure of Filler Panel
INST03-14-10 3.14 Power ON/OFF Procedure
INST03-14-10 3.14.1 Power ON Procedure
INST03-14-50 3.14.2 Power OFF Procedure
INST03-14-100 3.14.3 Method of Disconnecting Power Supply to Storage system
INST03-15-10 3.15 Mounting on Rack Frame
INST03-15-20 3.15.1 Mounting Lifter on Rack Frame
INST03-15-30 3.15.2 Mounting Storage system on Rack Frame
INST03-16-10 3.16 LAN Cable Wiring for SVP
INST03-16-20 3.16.1 Procedures of LAN Cable Wiring for SVP
INST03-17-10 3.17 Installation of SM Size without adding Cache Memory
INST03-18-10 3.18 Installation of Decoration Panel, Key Kit, Front Door, Front Door
Hinge Kit and PC Tray for RK42
(DKC-F810I-DECO/DECOP/KYH/KYP/FDR/FDH42/TR42)
INST03-18-20 3.18.1 Installation Procedure of Decoration Panel
(DKC-F810I-DECO/DECOP)
INST03-18-40 3.18.2 Installation Procedure of Key Kit (DKC-F810I-KYH)
INST03-18-60 3.18.3 Installation Procedure of Key Kit (DKC-F810I-KYP)
INST03-18-80 3.18.4 Installation Procedure of Front Door Hinge Kit
(DKC-F810I-FDH42)
INST03-18-100 3.18.5 Installation Procedure of Rack Front Door (DKC-F810I-FDR)
INST03-18-120 3.18.6 Installation Procedure of PC Tray for RK42

INST00-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST00-60

INST04-01-10 4. Hardware De-Installation

INST04-01-10 4.1 De-Installation of Disk Adapter, Drive and DEV Interface Cable
(DKC-F810I-SCA/CC1/CC2/CC4/300KCM/600JCM/900JCM/
1R2JCM/3R0H3M/4R0H3M/400MCM/800MCM/1R6FM/3R2FM)
INST04-01-50 4.1.1 Flowchart
INST04-01A-10 4.1.2 When performing removal of the data/spare Drive
(DKC-F810I-300KCM/600JCM/900JCM/1R2JCM/3R0H3M/
4R0H3M/400MCM/800MCM/1R6FM/3R2FM)
INST04-01B-10 4.1.3 When performing removal of the DKA and Device Interface
Cable (DKC-F810I-SCA/CC1/CC2)
INST04-01C-10 4.1.4 When performing removal of the data/spare Drive, Device
Interface Cable that accompanies the removal of the DKU
(DKC-F810I-CC1/CC2/CC4/300KCM/600JCM/900JCM/
1R2JCM/3R0H3M/4R0H3M/400MCM/800MCM/1R6FM/3R2FM)
INST04-01C-20 4.1.4.1 Storage System Configurations and Required I/F Cable
Options
INST04-01C-120 4.1.4.2 Setting up the New Device Structure Information
INST04-01C-210 4.1.4.3 De-Installation Procedure of Drive
INST04-01C-780 4.1.4.4 De-installation Procedure of Device Interface Cable CC1
(DKC-F810I-CC1)
INST04-01C-830 4.1.4.5 De-installation Procedure of Device Interface Cable CC2
(DKC-F810I-CC2)
INST04-01C-1010 4.1.4.6 De-installation Procedure of Device Interface Cable CC4
(DKC-F810I-CC4)
INST04-01C-1310 4.1.4.7 SVP post procedure
INST04-01D-10 4.1.5 When performing removal of the DKA and DEV interface cable
that accompanies the removal of the DKU-00/10
(only hardware procedure) (DKC-F810I-SCA/CC1/CC2)
INST04-01D-10 4.1.5.1 In the case of Standard Model
INST04-01D-180 4.1.5.2 In the case of High-performance Model
INST04-02-10 4.2 De-Installation of Drive Chassis
(DKC-F810I-UBX/SBX/FBX/SBBRAL/BUH/BUP/FMDRAL/BFH/BFP)
INST04-02-60 4.2.1 De-Installation Procedure of Drive Chassis
(DKC-F810I-UBX/SBX)
INST04-02-220 4.2.2 De-Installation Procedure of FMD Chassis (DKC-F810I-FBX)

INST00-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST00-70

INST04-03-10 4.3 De-Installation of Cache Memory, Cache Backup Module kit, Cache
Flash Memory and Inter-Controller Connecting Cable
(DKC-F810I-CM16G/CM32G/CPEX/BKMS/BKML/BMM128/BMM256/
MFC5/MFC30/MFC1J)
INST04-04A-10 4.4 De-Installation of Channel Adapter
INST04-04A-10 4.4.1 De-Installation of Fibre 8/16-port 8/16G Host Adapter
(DKC-F810I-16FC8/8FC16)
INST04-04B-10 4.4.2 De-Installation of Mainframe Fibre 16-port 8G Host Adapter
(DKC-F810I-16MS8/16ML8)
INST04-05-10 4.5 De-Installation of Processor Blade, HUB, Cache Memory, Cache
Backup Module kit and Cache Flash Memory, Inter-Controller
Connecting Kit and Inter-Controller Connecting Cable
(DKC-F810I-MP/HUB/CM16G/CM32G/CPEX/BKMS/BKML/BMM128/
BMM256/MOD5/MOD30/MOD1J/MFC5/MFC30/MFC1J)
INST04-05-40 4.5.1 De-Installation of Module (DKC-F810I-MP/HUB/CM16G/CM32G/
CPEX/BKMS/BKML/BMM128/BMM256/MOD5/MOD30/MOD1J/
MFC5/MFC30/MFC1J)
INST04-05A-10 4.5.2 De-Installation of Processor Blade, HUB (DKC-F810I-MP/HUB)
INST04-06-10 4.6 De-Installation of Controller Chassis
(DKC810I-CBXA, DKC-F810I-CBXB/CRF42/CRF3R/BCH/BCP)
INST04-06-50 4.6.1 De-Installation Procedure of Bezel
INST04-06-80 4.6.2 De-Installation Procedure of Controller Chassis
INST04-07-10 4.7 De-Installation of Rack and Side Cover
(DKC-F810I-RK42/SCOV/SCOVH)
INST04-07-20 4.7.1 De-Installation Procedure of Rack and Side Cover
INST04-08-10 4.8 De-Installation of Service Processor (DKC-F810I-SVP)
INST04-08-30 4.8.1 De-Installation Procedure of Service Processor
(DKC-F810I-SVP)
INST04-09-10 4.9 De-Installation of Power Cord Kit (DKC-F810I-PLUC/PHUC/PFUC/
PLEC/PHEC/PFEC/PLCC/PHCC/PFCC)
INST04-09-10 4.9.1 De-Installation of DKC Power Cord Kit
(DKC-F810I-PLUC/PLEC/PLCC)
INST04-09-90 4.9.2 De-Installation of DKU Power Cord Kit
(DKC-F810I-PHUC/PHEC/PHCC)
INST04-09-200 4.9.3 De-Installation of DKU (FBX) Power Cord Kit
(DKC-F810I-PFUC/PFEC/PFCC)
INST04-10-10 4.10 De-Installation of Filler Panel (DKC-F810I-FIHT)
INST04-10-20 4.10.1 De-Installation Procedure of Filler Panel

INST00-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST00-80

INST04-11-10 4.11 De-Installation of SM Size without removing Cache Memory

INST04-12-10 4.12 De-Installation of Decoration Panel, Key Kit, Front Door, Front Door
Hinge Kit and PC Tray for RK42
(DKC-F810I-DECO/DECOP/KYH/KYP/FDR/FDH42/TR42)
INST04-12-20 4.12.1 De-Installation Procedure of Decoration Panel
(DKC-F810I-DECO/DECOP)
INST04-12-40 4.12.2 De-Installation Procedure of Key Kit (DKC-F810I-KYH)
INST04-12-60 4.12.3 De-Installation Procedure of Key Kit (DKC-F810I-KYP)
INST04-12-80 4.12.4 De-Installation Procedure of Front Door Hinge Kit
(DKC-F810I-FDH42)
INST04-12-100 4.12.5 De-Installation Procedure of Rack Front Door
(DKC-F810I-FDR)
INST04-12-120 4.12.6 De-Installation Procedure of PC Tray for RK42
(DKC-F810I-TR42)

INST00-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST00-90

INST05-01-10 5. SVP procedure

INST05-01-10 5.1 INDEX
INST05-02-10 5.2 New Installation SVP Procedure
INST05-02-10 5.2.1 TOD Setting and Set IP Address
INST05-02-80 5.2.2 Configuration Information Definition
INST05-02-480 5.2.2.1 LDEV ID setting procedure when the emulation types of
different systems coexist
INST05-02-480 5.2.2.1.1 Coexistence in units of parity group
INST05-02-500 5.2.3 Check Procedure
INST05-02-540 5.2.4 Refer Configuration
INST05-03-10 5.3 Change Configuration SVP Procedure
INST05-03-10 5.3.1 Setting up the New Device Structure Information
INST05-03-20 5.3.1.1 System Option
INST05-03-40 5.3.1.2 DCR Configuration
INST05-03-90 5.3.1.3 CVS Configuration
INST05-03-450 5.3.1.4 LUN Management
INST05-03-900 5.3.2 Emulation Type Change
INST05-04-10 5.4 Procedure for connecting external servers
INST05-04-10 5.4.1 Connect SVP by remote desktop
INST05-04-30 5.4.2 Configure DNS Setting of SVP
INST05-05-10 5.5 Switch the Auto Account Lock Function

INST06-10 6. Storage Capacity and Cache Capacity, and the number of required options
INST06-10 6.1 Required CM Capacity

INST00-90
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-10

1. Storage system Configuration Outline

1.1 General Information
1.1.1 Model List
(1) Model list of DKC810I
Table 1.1.1-1 shows the model list of DKC810I.

Table 1.1.1-1 Model List of DKC810I

No. Model Number Model Name Major Part Remarks
1 DKC810I-CBXA Primary Controller Chassis • DKCPANEL × 1 This model name
• Logic PL × 1 doesn’t contain
• SSVPMN × 1 Power cables,
• DKCPS × 4 CHA, DKA and
• DKCFAN (Front) × 5 Rack.
• DKCFAN (Rear) × 5
• MPB (WP850-A) × 2
• CPEX (W840-A) × 2
• SVP × 1
2 DKC-F810I-CBXB Second Controller Chassis • DKCPANEL × 1 This model name
• Logic PL × 1 doesn’t contain
• SSVPMN × 1 Power cables,
• DKCPS × 4 CHA, DKA and
• DKCFAN (Front) × 5 Rack.
• DKCFAN (Rear) × 5
• MPB (WP850-A) × 2
• CPEX (W840-A) × 2
• HUBBOX × 1
3 DKC-F810I-CRF42 Controller Chassis Rail for RK42 • CBX Rail × 1
4 DKC-F810I-CRF3R Controller Chassis Rail for 3rd • CBX Rail × 1
Party Rack Frame
(To be continued)

INST01-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-20

(Continued from the preceding page)

No. Model Number Model Name Major Part Remarks
5 DKC-F810I-RK42 Rack • 42U Rack
• Rear Door
• Top Cover
6 DKC-F810I-SCOV Side Cover • Side Cover L × 3
• Side Cover R × 3
7 DKC-F810I-SCOVH Side Cover with HITACHI • Side Cover L × 3
description • Side Cover R × 3
8 DKC-F810I-DECO Decoration Panel • Decoration Panel for HDS
9 DKC-F810I-DECOP Decoration Panel • Decoration Panel for HP
10 DKC-F810I-KYH Key Kit • Handle ASSY × 1 for HDS
• Key × 1
11 DKC-F810I-KYP Key Kit • Bracket (KEY) × 1 for HP
• Stopper Bracket × 1
12 DKC-F810I-FDR Rack Front Door • Front Door × 1
13 DKC-F810I-RDH42 Front Door Hinge Kit • Hinge × 2
• Stopper × 1
14 DKC-F810I-TR42 PC Tray for RK42 • PC Tray × 1
• Hinge × 2
15 DKC-F810I-FIHT Filler Panel • Filler Panel for HDS
16 DKC-F810I-UBX LFF Drive Chassis • SBB (3.5 inch) × 8
17 DKC-F810I-SBX SFF Drive Chassis • SBB (2.5 inch) × 8
18 DKC-F810I-FBX FMD Chassis • FMU × 4
• Rail × 4
19 DKC-F810I-SBBRAL Drive Chassis Rail for SBX/UBX • Rail × 16
20 DKC-F810I-FMDRAL Drive Chassis Rail for FBX • Rail × 8
21 DKC-F810I-BCH Controller Chassis Bezel • DKC Bezel (8U) × 1 For HDS
• DKC Bezel (2U) × 1
22 DKC-F810I-BCP Controller Chassis Bezel • DKC Bezel (8U) × 1 For HP
• DKC Bezel (2U) × 1
23 DKC-F810I-BUH Drive Chassis Bezel • DKU Bezel × 2 For HDS
24 DKC-F810I-BUP Drive Chassis Bezel • DKU Bezel × 2 For HP
25 DKC-F810I-BFH FMD Chassis Bezel • DKU Bezel × 1 For HDS
26 DKC-F810I-BFP FMD Chassis Bezel • DKU Bezel × 1 For HP
27 DKC-F810I-MOD5 Inter-Controller Connecting Kit • MODCON × 2
• MODCON Cable × 2
• LAN Cable × 1
• MFC Cable × 8
28 DKC-F810I-MOD30 Inter-Controller Connecting Kit • MODCON × 2
• MODCON Cable × 2
• LAN Cable × 1
• MFC Cable × 8
(To be continued)

INST01-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-30

(Continued from the preceding page)

No. Model Number Model Name Major Part Remarks
29 DKC-F810I-MOD1J Inter-Controller Connecting Kit
• MODCON × 2
• MODCON Cable × 2
• LAN Cable × 1
• MFC Cable × 8
30 DKC-F810I-MFC5 Inter-Controller Connecting Cable • MFC Cable × 8
31 DKC-F810I-MFC30 Inter-Controller Connecting Cable • MFC Cable × 8
32 DKC-F810I-MFC1J Inter-Controller Connecting Cable • MFC Cable × 8
33 DKC-F810I-CC1 Device Interface Cable CC1 • Copper Cable 1m × 8
34 DKC-F810I-CC2 Device Interface Cable CC2 • Copper Cable 2m × 8
35 DKC-F810I-CC4 Device Interface Cable CC4 • Copper Cable 4m × 8
36 DKC-F810I-FC5 Device Interface Cable FC5 • Optical Cable 5m × 8
37 DKC-F810I-FC30 Device Interface Cable FC30 • Optical Cable 30m × 8
38 DKC-F810I-FC1J Device Interface Cable FC1J • Optical Cable 100m × 8
39 DKC-F810I-SVP Additional Service Processor • SVP × 1
40 DKC-F810I-HUB Additional HUB • HUBBOX × 1
41 DKC-F810I-PLUC DKC Power Cord Kit (USA) • Power Cord × 4
42 DKC-F810I-PHUC DKU Power Cord Kit (USA) • Power Cord × 4
43 DKC-F810I-PFUC FBX Power Cord Kit (USA) • Power Cord × 8
44 DKC-F810I-PLEC DKC Power Cord Kit (EU) • Power Cord × 4
45 DKC-F810I-PHEC DKU Power Cord Kit (EU) • Power Cord × 4
46 DKC-F810I-PFEC FBX Power Cord Kit (EU) • Power Cord × 8
47 DKC-F810I-PLCC DKC Power Cord Kit (China) • Power Cord × 4
48 DKC-F810I-PHCC DKU Power Cord Kit (China) • Power Cord × 4
49 DKC-F810I-PFCC FBX Power Cord Kit (China) • Power Cord × 8
50 DKC-F810I-MP Additional Processor Blade • MPB (WP850-A) × 2
51 DKC-F810I-CPEX Additional Cache Path Control • CPEX (WP840-A) × 2
Adapter
52 DKC-F810I-CM16G Cache Memory (16GB) • 16GB DIMM × 1
53 DKC-F810I-CM32G Cache Memory (32GB) • 32GB DIMM × 1
54 DKC-F810I-BKMS Cache Backup Module Kit for • BKM× 2
Small Memory • Battery (Ni-MH) × 4
55 DKC-F810I-BKML Cache Backup Module Kit for • BKM× 2
Large Memory • Battery (Li-ion) × 4
56 DKC-F810I-BMM128 Cache Flash Memory (128GB) • SSD (128GB) × 1
57 DKC-F810I-BMM256 Cache Flash Memory (256GB) • SSD (256GB) × 1
58 DKC-F810I-SCA Disk Adapter • DKA (WP820-A) × 2 (*1)
(To be continued)

INST01-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-40

(Continued from the preceding page)

No. Model Number Model Name Major Part Remarks
59 DKC-F810I-16FC8 Fibre 16-port 8G Host Adapter • WP810-A × 2
60 DKC-F810I-8FC16 Fibre 8-port 16G Host Adapter • WP812-A × 2 Will be
supported from
2014 April or
later.
61 DKC-F810I-16MS8 Mainframe Fibre 16-port 8G Host • WP811-A × 2
Adapter for Shortwave
62 DKC-F810I-16ML8 Mainframe Fibre 16-port 8G Host • WP811-B × 2
Adapter for Longwave
63 DKC-F810I-1PS8 SFP for 8Gbps Shortwave • Fibre 8Gbps SFP
(Shortwave) × 1
64 DKC-F810I-1PL8 SFP for 8Gbps Longwave • Fibre 8Gbps SFP
(Longwave) × 1
65 DKC-F810I-1PS16 SFP for 16Gbps Shortwave • Fibre 16Gbps SFP
(Shortwave) × 1
66 DKC-F810I-1PL16 SFP for 16Gbps Longwave • Fibre 16Gbps SFP
(Longwave) × 1
(To be continued)

INST01-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-50

(Continued from the preceding page)

No. Model Number Model Name Major Part Remarks
67 DKC-F810I-300KCM SFF 300GB Disk Drive • HDU800-300KCMSS 2.5 inch
×1 300GB/15k
HDD 6Gb SAS
68 DKC-F810I-600JCM SFF 600GB Disk Drive • HDU800-600JCMSS 2.5 inch
×1 600GB/10k
HDD 6Gb SAS
69 DKC-F810I-900JCM SFF 900GB Disk Drive • HDU800-900JCMSS 2.5 inch
×1 900GB/10k
HDD 6Gb SAS
70 DKC-F810I-1R2JCM SFF 1.2TB Disk Drive • HDU800-1R2JCMSS 2.5 inch
×1 1.2TB/10k HDD
6Gb SAS
71 DKC-F810I-3R0H3M LFF 3TB Disk Drive • HDU800-3R0H3MSS × 1 3.5 inch
3TB/7.2k HDD
6Gb SAS
72 DKC-F810I-4R0H3M LFF 4TB Disk Drive • HDU800-4R0H3MSS × 1 3.5 inch
4TB/7.2k HDD
6Gb SAS
73 DKC-F810I-400MCM SFF 400GB SSD Drive • HDU800-400MCMSS 2.5 inch 400GB
×1 SSD 6Gb SAS
MLC
74 DKC-F810I-800MCM SFF 800GB SSD Drive • HDU800-800MCMSS 2.5 inch 800GB
×1 SSD 6Gb SAS
MLC
75 DKC-F810I-1R6FM 1.6TB Flash Module Drive • HDU800-1R6FMSS × 1
76 DKC-F810I-3R2FM 3.2TB Flash Module Drive • HDU800-3R2FMSS × 1

*1: When the second DKC-F810I-SCA is installed, the Device Interface Cables between DKA and
DKU, and between DKU and DKU are required to be connected.

INST01-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-60

(2) Correspondence of Model Number and Drive Model Name

Table 1.1.1-2 Correspondence list of Model Number and Drive Model Name
No. Model Number FRU Name Drive Model Name
1 DKC-F810I-300KCM HDU800-300KCMSS S5C-K300SS
2 DKC-F810I-600JCM HDU800-600JCMSS R5D-J600SS
3 DKC-F810I-900JCM HDU800-900JCMSS R5D-J900SS
4 DKC-F810I-1R2JCM HDU800-1R2JCMSS R5E-J1R2SS
5 DKC-F810I-3R0H3M HDU800-3R0H3MSS S2E-H3R0SS
6 DKC-F810I-4R0H3M HDU800-4R0H3MSS S2E-H4R0SS
7 DKC-F810I-400MCM HDU800-400MCMSS B5A-M400SS
8 DKC-F810I-800MCM HDU800-800MCMSS B5A-M800SS
9 DKC-F810I-1R6FM HDU800-1R6FMSS HAA-P1R6SS
10 DKC-F810I-3R2FM HDU800-3R2FMSS HAB-P3R2SS

INST01-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-70

(3) Disk drive model

SVP displays each drive model as the following table.

Disk drive model SVP screen Drive Form Factor
DKS5C-K300SS DKS5C-K300SS 2.5 inch SAS HDD
DKR5D-J600SS DKR5D-J600SS 2.5 inch SAS HDD
DKR5D-J900SS DKR5D-J900SS 2.5 inch SAS HDD
DKR5E-J1R2SS DKR5E-J1R2SS 2.5 inch SAS HDD
DKS2E-H3R0SS DKS2E-H3R0SS 3.5 inch SAS HDD
DKS2E-H4R0SS DKS2E-H4R0SS 3.5 inch SAS HDD
SLB5A-M400SS SLB5A-M400SS 2.5 inch SSD
SLB5A-M800SS SLB5A-M800SS 2.5 inch SSD
NFHAA-P1R6SS NFHAA-P1R6SS Flash Module Drive
NFHAB-P3R2SS NFHAB-P3R2SS Flash Module Drive

INST01-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-80

(4) SVP screen display and conversion table of option type names

• SVP screen display of CHA

Model Number SVP screen
DKC-F810I-16FC8 16F8C (Fibre)
DKC-F810I-16ML8 16ML8 (Mfibre)
DKC-F810I-16MS8 16MS8 (Mfibre)

• SVP screen display of DKA

Model Number SVP screen
DKC-F810I-SCA DKA (4Port)

• SVP screen display of Cache memory

Model Number SVP screen
DKC-F810I-C32G C32G
DKC-F810I-C64G C64G

INST01-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-90

1.1.2 Configuration
1.1.2.1 Controller Chassis Configuration
(1) CHA Options Installation Rule
The CHA options can be installed also in the DKA slots in addition to the CHA slots in
DKC810I. After the dedicated CHA slots are fully installed, the CHA options can be installed
in the DKA slots.
The order of CHA installation is shown below.

Table 1.1.2.1-1 CHA Installation Rule

Installation Installation Slot Location
Order Diskless Model Standard Model High Performance Model
DKC810I- DKC-F810I- DKC810I- DKC-F810I- DKC810I- DKC-F810I-
CBXA CBXB CBXA CBXB CBXA CBXB
1 1PC/2PC 1PJ/2PJ 1PC/2PC 1PJ/2PJ 1PC/2PC 1PJ/2PJ
(CHA0) (CHA6) (CHA0) (CHA6) (CHA0) (CHA6)
2 1PD/2PD 1PK/2PK 1PD/2PD 1PK/2PK 1PD/2PD 1PK/2PK
(CHA1) (CHA7) (CHA1) (CHA7) (CHA1) (CHA7)
3 1PE/2PE 1PL/2PL 1PE/2PE 1PL/2PL 1PE/2PE 1PL/2PL
(CHA2/MPB3) (CHA8/MPB7) (CHA2/MPB3) (CHA8/MPB7) (CHA2/MPB3) (CHA8/MPB7)
4 1PF/2PF 1PM/2PM 1PF/2PF 1PM/2PM 1PF/2PF 1PM/2PM
(CHA3/MPB2) (CHA9/MPB6) (CHA3/MPB2) (CHA9/MPB6) (CHA3/MPB2) (CHA9/MPB6)
5 1PB/2PB 1PH/2PH 1PB/2PB 1PH/2PH — —
(DKA1/CHA4) (DKA3/CHA10) (DKA1/CHA4) (DKA3/CHA10)
6 1PA/2PA 1PG/2PG — 1PG/2PG — —
(DKA0/CHA5) (DKA2/CHA11) (DKA2/CHA11)

Table 1.1.2.1-2 Possible Diskless CHA configurations

DKC810I- 1PC/2PC 1PD/2PD 1PE/2PE 1PF/2PF 1PB/2PB 1PA/2PA Max Host Ports
CBXA (CHA0) (CHA1) (CHA2/MPB3) (CHA3/MPB2) (CHA4/DKA1) (CHA5/DKA0) (*1)
Mainframe 16MS8/16ML8 16MS8/16ML8 16MS8/16ML8 16MS8/16ML8 16MS8/16ML8 8FC16/16FC8 Mainframe =80;
Open FC=6/14
Open FC 8FC16/16FC8 8FC16/16FC8 8FC16/16FC8 8FC16/16FC8 8FC16/16FC8 8FC16/16FC8 Open FC 46/94

DKC-F810I- 1PJ/2PJ 1PK/2PK 1PL/2PL 1PM/2PM 1PH/2PH 1PG/2PG Max Host Ports
CBXB (CHA6) (CHA7) (CHA8/MPB7) (CHA9/MPB6) (CHA10/DKA3) (CHA11/DKA2) (*1)
Mainframe 16MS8/16ML8 16MS8/16ML8 16MS8/16ML8 16MS8/16ML8 16MS8/16ML8 8FC16/16FC8 Mainframe =80;
Open FC=6/14
Open FC 8FC16/16FC8 8FC16/16FC8 8FC16/16FC8 8FC16/16FC8 8FC16/16FC8 8FC16/16FC8 Open FC 46/94

*1: This depends on the number of UVM paths to external disks. The recommended minimum
is 2 paths to UVM disk.

INST01-90
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-100

(2) MPB Options Installation Rule

The MPB options can be installed also in the CHA slots in addition to the MPB slots in
DKC810I.

Table 1.1.2.1-3 MPB Installation Rule

Installation Installation Slot Location
Order DKC810I-CBXA DKC-F810I-CBXB
1 1MA/2MA (MPB0) 1MC/2MC (MPB4)
2 1MB/2MB (MPB1) 1MD/2MD (MPB5)
3 1PF/2PF (CHA3/MPB2) (*1) 1PM/2PM (CHA9/MPB6) (*2)
4 1PE/2PE (CHA2/MPB3) (*1) 1PL/2PL (CHA8/MPB7) (*2)

*1: If MPB2/MPB3 is/are installed, DKC-F810I-HUB or DKC-F810I-SVP is required.

*2: If MPB6/MPB7 is/are installed, DKC-F810I-HUB is required.

(3) DKA Options Installation Rule

Table 1.1.2.1-4 DKA Installation Rule

Installation Installation Slot Location
Order DKC810I-CBXA DKC-F810I-CBXB
1 1PA/2PA (DKA0) 1PG/2PG (DKA2)
2 1PB/2PB (DKA1) 1PH/2PH (DKA3)

INST01-100
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-110

(4) SVP and HUB Options Installation Rule

The Additional SVP (DKC-F810I-SVP) necessary for SVP duplication can be installed in
DKC810I-CBXA (Primary Controller Chassis) only. Additional SVP cannot be installed in
DKC-F810I-CBXB (Second Controller Chassis).

Table 1.1.2.1-5 SVP/HUB Installation Rule

Installed model
No. DKC810I-CBXA DKC-F810I-CBXB
SVP-BASIC slot SVP-OPTION/ HUBBOX-10 slot HUBBOX-11 slot
HUBBOX-01 slot
1 SVP — HUB —
(Standard equipment) (Standard equipment)
2 SVP DKC-F810I-HUB (*1) HUB —
(Standard equipment) (Standard equipment)
3 SVP DKC-F810I-HUB (*1) HUB DKC-F810I-HUB (*2)
(Standard equipment) (Standard equipment)
4 SVP DKC-F810I-SVP (*3) HUB —
(Standard equipment) (Standard equipment)
5 SVP DKC-F810I-SVP (*3) HUB DKC-F810I-HUB (*2)
(Standard equipment) (Standard equipment)

*1: When 2nd DKC-F810I-MP (1PF/2PF) is installed in the DKC810I-CBXA.

*2: When 2nd DKC-F810I-MP (1PM/2PM) is installed in the DKC-F810I-CBXB.
*3: In Case to make SVP duplicated.

INST01-110
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-120

1.1.2.2 Cache Memory Upgrade Table

NOTICE: To create a CLPR, if your storage system has any additional printed circuit
boards (PCBs), you must install the cache memories with the High
Performance Cache Access Model. There is a case of that expansion of
cache memory. If necessary, see INST03-10-10.

The method of installing the cache memory has two types.

Serial Installation
When the cache memory on the standard equipped Cache Path Control Adapter (CPEX-0) is
installed to the full and the additional cache memory capacity is necessary, install DKC-F810I-
CPEX Cache Path Control Adapter (CPEX-1) to increase cache memory further. When the
cache memory on CPEX-1 is full, install two DKC-F810I-CPEX Cache Path Control Adapter
(CPEX-2 and CPEX-3) in the second Controller Chassis to increase cache memory.

DKC-F810I- DKC-F810I-CPEX DKC-F810I-CPEX

CM16G/CM32G

DKC-F810I-
CM16G/CM32G

CPEX-0 CPEX-1 CPEX-2 CPEX-3

(*1) (*1)

DKC810I-CBXA DKC-F810I-CBXB
When the CM-DIMM is installed on the To expand the CM capacity after CPEX-1 is filled
CPEX-0 to the full, add the CPEX-1. with CM-CIMM, install DKC-F810I-CBXB and add
CM-DIMM simultaneously into the CPEX-2 and
CPEX-3.
*1: standard equipment

Fig. 1.1.2.2-1 Serial Installation

INST01-120
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-130

Parallel Installation
This model distributes the cache memory to the multiple (2 or 4 sets) Cache Path Control
Adapters.

Distributes CM-DIMM to each CPEX board

DKC-F810I-
CM16G/CM32G

DKC-F810I-
CM16G/CM32G

CPEX-0 CPEX-1 CPEX-2 CPEX-3 DKC-F810I-CPEX

(*1) (*1)

DKC810I-CBXA DKC-F810I-CBXB

*1: standard equipment

Fig. 1.1.2.2-2 Parallel Installation

INST01-130
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-140

The cache memory capacities and the corresponding number of options required are shown in Table
1.1.2.2-1 through 1.1.2.2-6.

Table 1.1.2.2-1 Cache Memory Upgrade Table 

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM16G CPEX BKMS/ BMM128/
(*1, *2) (*1) BKML BMM256
1 32GB 32 — — — 2 0 1 2
2 64GB 64 — — — 4 0 1 2
3 96GB 96 — — — 6 0 1 2
4 128GB 128 — — — 8 0 1 2
5 160GB 160 — — — 10 0 1 2
6 192GB 192 — — — 12 0 1 2
7 224GB 224 — — — 14 0 1 2
8 256GB 256 — — — 16 0 1 2
9 288GB 256 32 — — 18 1 2 4
10 320GB 256 64 — — 20 1 2 4
11 356GB 256 96 — — 22 1 2 4
12 384GB 256 128 — — 24 1 2 4
13 416GB 256 160 — — 26 1 2 4
14 448GB 256 192 — — 28 1 2 4
15 480GB 256 224 — — 30 1 2 4
16 512GB 256 256 — — 32 1 2 4
17 576GB 256 256 32 32 36 2 4 8
18 608GB 256 256 64 32 38 2 4 8
19 640GB 256 256 64 64 40 2 4 8
20 672GB 256 256 96 64 42 2 4 8
21 704GB 256 256 96 96 44 2 4 8
22 736GB 256 256 128 96 46 2 4 8
23 768GB 256 256 128 128 48 2 4 8
24 800GB 256 256 160 128 50 2 4 8
25 832GB 256 256 160 160 52 2 4 8
26 864GB 256 256 192 160 54 2 4 8
27 896GB 256 256 192 192 56 2 4 8
28 928GB 256 256 224 192 58 2 4 8
29 960GB 256 256 224 224 60 2 4 8
30 992GB 256 256 256 224 62 2 4 8
31 1024GB 256 256 256 256 64 2 4 8

*1: Standard equipment.

*2: The required SM capacity shown in Table 6.1-1 (INST06-10) must be installed in CPEX-
0.

INST01-140
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-150

Table 1.1.2.2-2 Cache Memory Upgrade Table 

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM32G CPEX BKMS BKML BMM BMM
(*1, *2) (*1) 128 256
1 64GB 64 — — — 2 0 1 0 2 0
2 128GB 128 — — — 4 0 1 0 2 0
3 192GB 192 — — — 6 0 1 0 2 0
4 256GB 256 — — — 8 0 1 0 2 0
5 320GB 320 — — — 10 0 0 1 0 2
6 384GB 384 — — — 12 0 0 1 0 2
7 448GB 448 — — — 14 0 0 1 0 2
8 512GB 512 — — — 16 0 0 1 0 2
9 576GB 512 64 — — 18 1 1 1 2 2
10 640GB 512 128 — — 20 1 1 1 2 2
11 704GB 512 192 — — 22 1 1 1 2 2
12 768GB 512 256 — — 24 1 1 1 2 2
13 832GB 512 320 — — 26 1 0 2 0 4
14 896GB 512 384 — — 28 1 0 2 0 4
15 960GB 512 448 — — 30 1 0 2 0 4
16 1024GB 512 512 — — 32 1 0 2 0 4
17 1152GB 512 512 64 64 36 2 2 2 4 4
18 1216GB 512 512 128 64 38 2 2 2 4 4
19 1280GB 512 512 128 128 40 2 2 2 4 4
20 1344GB 512 512 192 128 42 2 2 2 4 4
21 1408GB 512 512 192 192 44 2 2 2 4 4
22 1472GB 512 512 256 192 46 2 2 2 4 4
23 1536GB 512 512 256 256 48 2 2 2 4 4
24 1600GB 512 512 320 256 50 2 1 3 2 6
25 1664GB 512 512 320 320 52 2 0 4 0 8
26 1728GB 512 512 384 320 54 2 0 4 0 8
27 1792GB 512 512 384 384 56 2 0 4 0 8
28 1856GB 512 512 448 384 58 2 0 4 0 8
29 1920GB 512 512 448 448 60 2 0 4 0 8
30 1984GB 512 512 512 448 62 2 0 4 0 8
31 2048GB 512 512 512 512 64 2 0 4 0 8

*1: Standard equipment.

*2: The required SM capacity shown in Table 6.1-1 (INST06-10) must be installed in CPEX-
0.

INST01-150
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-160

Table 1.1.2.2-3 Cache Memory Upgrade Table 

Cache Memory Capacity Number of options
Cache (GB)
No. Memory DKC810I-CBXA DKC-F810I-
Capacity CPEX-0 CPEX-1 CM16G CPEX BKMS BKML BMM BMM
(*1, *2) 128 256
1 64GB 32 32 4 1 2 0 4 0
2 96GB 64 32 6 1 2 0 4 0
3 128GB 64 64 8 1 2 0 4 0
4 128GB 96 32 8 1 2 0 4 0
5 160GB 96 64 10 1 2 0 4 0
6 160GB 128 32 10 1 2 0 4 0
7 192GB 96 96 12 1 2 0 4 0
8 192GB 128 64 12 1 2 0 4 0
9 192GB 160 32 12 1 2 0 4 0
10 224GB 128 96 14 1 2 0 4 0
11 224GB 160 64 14 1 2 0 4 0
12 224GB 192 32 14 1 2 0 4 0
13 256GB 128 128 16 1 2 0 4 0
14 256GB 160 96 16 1 2 0 4 0
15 256GB 192 64 16 1 2 0 4 0
16 256GB 224 32 16 1 2 0 4 0
17 288GB 160 128 18 1 2 0 4 0
18 288GB 192 96 18 1 2 0 4 0
19 288GB 224 64 18 1 2 0 4 0
20 288GB 256 32 18 1 2 0 4 0
21 320GB 160 160 20 1 2 0 4 0
22 320GB 192 128 20 1 2 0 4 0
23 320GB 224 96 20 1 2 0 4 0
24 320GB 256 64 20 1 2 0 4 0
25 352GB 192 160 22 1 2 0 4 0
26 352GB 224 128 22 1 2 0 4 0
27 352GB 256 96 22 1 2 0 4 0
28 384GB 192 192 24 1 2 0 4 0
29 384GB 224 160 24 1 2 0 4 0
30 384GB 256 128 24 1 2 0 4 0
31 416GB 224 192 26 1 2 0 4 0
32 416GB 256 160 26 1 2 0 4 0
33 448GB 224 224 28 1 2 0 4 0
34 448GB 256 192 28 1 2 0 4 0
35 480GB 256 224 30 1 2 0 4 0
36 512GB 256 256 32 1 2 0 4 0

*1: Standard equipment.

*2: The required SM capacity shown in Table 6.1-1 (INST06-10) must be installed in CPEX-
0.
INST01-160
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-170

Table 1.1.2.2-4 Cache Memory Upgrade Table 

Cache Memory Capacity Number of options
Cache (GB)
No. Memory DKC810I-CBXA DKC-F810I-
Capacity CPEX-0 CPEX-1 CM32G CPEX BKMS BKML BMM BMM
(*1, *2) 128 256
1 128GB 64 64 4 1 2 0 4 0
2 192GB 128 64 6 1 2 0 4 0
3 256GB 128 128 8 1 2 0 4 0
4 256GB 192 64 8 1 2 0 4 0
5 320GB 192 128 10 1 2 0 4 0
6 320GB 256 64 10 1 2 0 4 0
7 384GB 192 192 12 1 2 0 4 0
8 384GB 256 128 12 1 2 0 4 0
9 384GB 320 64 12 1 1 1 2 2
10 448GB 256 192 14 1 2 0 4 0
11 448GB 320 128 14 1 1 1 2 2
12 448GB 384 64 14 1 1 1 2 2
13 512GB 256 256 16 1 2 0 4 0
14 512GB 320 192 16 1 1 1 2 2
15 512GB 384 128 16 1 1 1 2 2
16 512GB 448 64 16 1 1 1 2 2
17 576GB 320 256 18 1 1 1 2 2
18 576GB 384 192 18 1 1 1 2 2
19 576GB 448 128 18 1 1 1 2 2
20 576GB 512 64 18 1 1 1 2 2
21 640GB 320 320 20 1 0 2 0 4
22 640GB 384 256 20 1 1 1 2 2
23 640GB 448 192 20 1 1 1 2 2
24 640GB 512 128 20 1 1 1 2 2
25 704GB 384 320 22 1 0 2 0 4
26 704GB 448 256 22 1 1 1 2 2
27 704GB 512 192 22 1 1 1 2 2
28 768GB 384 384 24 1 0 2 0 4
29 768GB 448 320 24 1 0 2 0 4
30 768GB 512 256 24 1 1 1 2 2
31 832GB 448 384 26 1 0 2 0 4
32 832GB 512 320 26 1 0 2 0 4
33 896GB 448 448 28 1 0 2 0 4
34 896GB 512 384 28 1 0 2 0 4
35 960GB 512 448 30 1 0 2 0 4
36 1024GB 512 512 32 1 0 2 0 4

*1: Standard equipment.

*2: The required SM capacity shown in Table 6.1-1 (INST06-10) must be installed in CPEX-
0.
INST01-170
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-180

Table 1.1.2.2-5 Cache Memory Upgrade Table 

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
(*1, *2) (*1) 16G 128 256
1 64 32 0 32 0 4 0 1 0 2 — 4 —
2 96 64 0 32 0 6 0 1 0 2 — 4 —
3 128 32 32 32 32 8 2 1 1 4 — 8 —
4 128 64 0 64 0 8 0 1 0 2 — 4 —
5 128 96 0 32 0 8 0 1 0 2 — 4 —
6 160 64 32 32 32 10 2 1 1 4 — 8 —
7 160 96 0 64 0 10 0 1 0 2 — 4 —
8 160 128 0 32 0 10 0 1 0 2 — 4 —
9 192 64 32 64 32 12 2 1 1 4 — 8 —
10 192 64 64 32 32 12 2 1 1 4 — 8 —
11 192 96 0 96 0 12 0 1 0 2 — 4 —
12 192 96 32 32 32 12 2 1 1 4 — 8 —
13 192 128 0 64 0 12 0 1 0 2 — 4 —
14 192 160 0 32 0 12 0 1 0 2 — 4 —
15 224 64 64 64 32 14 2 1 1 4 — 8 —
16 224 96 64 32 32 14 2 1 1 4 — 8 —
17 224 128 32 32 32 14 2 1 1 4 — 8 —
18 224 160 0 64 0 14 0 1 0 2 — 4 —
19 224 192 0 32 0 14 0 1 0 2 — 4 —
20 256 64 64 64 64 16 2 1 1 4 — 8 —
21 256 96 32 96 32 16 2 1 1 4 — 8 —
22 256 96 64 64 32 16 2 1 1 4 — 8 —
23 256 96 96 32 32 16 2 1 1 4 — 8 —
24 256 128 0 128 0 16 0 1 0 2 — 4 —
25 256 128 64 32 32 16 2 1 1 4 — 8 —
26 256 160 0 96 0 16 0 1 0 2 — 4 —
27 256 160 32 32 32 16 2 1 1 4 — 8 —
28 256 192 0 64 0 16 0 1 0 2 — 4 —
29 256 224 0 32 0 16 0 1 0 2 — 4 —
30 288 96 64 64 64 18 2 1 1 4 — 8 —
31 288 96 64 96 32 18 2 1 1 4 — 8 —
32 288 96 96 64 32 18 2 1 1 4 — 8 —
33 288 128 64 64 32 18 2 1 1 4 — 8 —
34 288 128 96 32 32 18 2 1 1 4 — 8 —
35 288 160 0 128 0 18 0 1 0 2 — 4 —
(To be continued)

INST01-180
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-190

(Continued from the preceding page)

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
(*1, *2) (*1) 16G 128 256
36 288 160 64 32 32 18 2 1 1 4 — 8 —
37 288 192 0 96 0 18 0 1 0 2 — 4 —
38 288 192 32 32 32 18 2 1 1 4 — 8 —
39 288 224 0 64 0 18 0 1 0 2 — 4 —
40 288 256 0 32 0 18 0 1 0 2 — 4 —
41 320 96 64 96 64 20 2 1 1 4 — 8 —
42 320 96 96 64 64 20 2 1 1 4 — 8 —
43 320 96 96 96 32 20 2 1 1 4 — 8 —
44 320 128 32 128 32 20 2 1 1 4 — 8 —
45 320 128 64 64 64 20 2 1 1 4 — 8 —
46 320 128 96 64 32 20 2 1 1 4 — 8 —
47 320 128 128 32 32 20 2 1 1 4 — 8 —
48 320 160 0 160 0 20 0 1 0 2 — 4 —
49 320 160 64 64 32 20 2 1 1 4 — 8 —
50 320 160 96 32 32 20 2 1 1 4 — 8 —
51 320 192 0 128 0 20 0 1 0 2 — 4 —
52 320 192 64 32 32 20 2 1 1 4 — 8 —
53 320 224 0 96 0 20 0 1 0 2 — 4 —
54 320 224 32 32 32 20 2 1 1 4 — 8 —
55 320 256 0 64 0 20 0 1 0 2 — 4 —
56 352 96 96 96 64 22 2 1 1 4 — 8 —
57 352 128 64 128 32 22 2 1 1 4 — 8 —
58 352 128 96 64 64 22 2 1 1 4 — 8 —
59 352 128 96 96 32 22 2 1 1 4 — 8 —
60 352 128 128 64 32 22 2 1 1 4 — 8 —
61 352 160 64 64 64 22 2 1 1 4 — 8 —
62 352 160 96 64 32 22 2 1 1 4 — 8 —
63 352 160 128 32 32 22 2 1 1 4 — 8 —
64 352 192 0 160 0 22 0 1 0 2 — 4 —
65 352 192 64 64 32 22 2 1 1 4 — 8 —
66 352 192 96 32 32 22 2 1 1 4 — 8 —
67 352 224 0 128 0 22 0 1 0 2 — 4 —
68 352 224 64 32 32 22 2 1 1 4 — 8 —
69 352 256 0 96 0 22 0 1 0 2 — 4 —
70 352 256 32 32 32 22 2 1 1 4 — 8 —
(To be continued)

INST01-190
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-200

(Continued from the preceding page)

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
(*1, *2) (*1) 16G 128 256
71 384 96 96 96 96 24 2 1 1 4 — 8 —
72 384 128 64 128 64 24 2 1 1 4 — 8 —
73 384 128 96 96 64 24 2 1 1 4 — 8 —
74 384 128 96 128 32 24 2 1 1 4 — 8 —
75 384 128 128 64 64 24 2 1 1 4 — 8 —
76 384 128 128 96 32 24 2 1 1 4 — 8 —
77 384 160 32 160 32 24 2 1 1 4 — 8 —
78 384 160 96 64 64 24 2 1 1 4 — 8 —
79 384 160 96 96 32 24 2 1 1 4 — 8 —
80 384 160 128 64 32 24 2 1 1 4 — 8 —
81 384 160 160 32 32 24 2 1 1 4 — 8 —
82 384 192 0 192 0 24 0 1 0 2 — 4 —
83 384 192 64 64 64 24 2 1 1 4 — 8 —
84 384 192 96 64 32 24 2 1 1 4 — 8 —
85 384 192 128 32 32 24 2 1 1 4 — 8 —
86 384 224 0 160 0 24 0 1 0 2 — 4 —
87 384 224 64 64 32 24 2 1 1 4 — 8 —
88 384 224 96 32 32 24 2 1 1 4 — 8 —
89 384 256 0 128 0 24 0 1 0 2 — 4 —
90 384 256 64 32 32 24 2 1 1 4 — 8 —
91 416 128 96 96 96 26 2 1 1 4 — 8 —
92 416 128 96 128 64 26 2 1 1 4 — 8 —
93 416 128 128 96 64 26 2 1 1 4 — 8 —
94 416 128 128 128 32 26 2 1 1 4 — 8 —
95 416 160 64 160 32 26 2 1 1 4 — 8 —
96 416 160 96 96 64 26 2 1 1 4 — 8 —
97 416 160 128 64 64 26 2 1 1 4 — 8 —
98 416 160 128 96 32 26 2 1 1 4 — 8 —
99 416 160 160 64 32 26 2 1 1 4 — 8 —
100 416 192 96 64 64 26 2 1 1 4 — 8 —
101 416 192 96 96 32 26 2 1 1 4 — 8 —
102 416 192 128 64 32 26 2 1 1 4 — 8 —
103 416 192 160 32 32 26 2 1 1 4 — 8 —
104 416 224 0 192 0 26 0 1 0 2 — 4 —
105 416 224 64 64 64 26 2 1 1 4 — 8 —
(To be continued)

INST01-200
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-210

(Continued from the preceding page)

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
(*1, *2) (*1) 16G 128 256
106 416 224 96 64 32 26 2 1 1 4 — 8 —
107 416 224 128 32 32 26 2 1 1 4 — 8 —
108 416 256 0 160 0 26 0 1 0 2 — 4 —
109 416 256 96 32 32 26 2 1 1 4 — 8 —
110 448 128 96 128 96 28 2 1 1 4 — 8 —
111 448 128 128 96 96 28 2 1 1 4 — 8 —
112 448 128 128 128 64 28 2 1 1 4 — 8 —
113 448 160 64 160 64 28 2 1 1 4 — 8 —
114 448 160 96 96 96 28 2 1 1 4 — 8 —
115 448 160 96 160 32 28 2 1 1 4 — 8 —
116 448 160 128 96 64 28 2 1 1 4 — 8 —
117 448 160 128 128 32 28 2 1 1 4 — 8 —
118 448 160 160 64 64 28 2 1 1 4 — 8 —
119 448 160 160 96 32 28 2 1 1 4 — 8 —
120 448 192 32 192 32 28 2 1 1 4 — 8 —
121 448 192 96 96 64 28 2 1 1 4 — 8 —
122 448 192 128 64 64 28 2 1 1 4 — 8 —
123 448 192 128 96 32 28 2 1 1 4 — 8 —
124 448 192 160 64 32 28 2 1 1 4 — 8 —
125 448 192 192 32 32 28 2 1 1 4 — 8 —
126 448 224 0 224 0 28 0 1 0 2 — 4 —
127 448 224 96 64 64 28 2 1 1 4 — 8 —
128 448 224 96 96 32 28 2 1 1 4 — 8 —
129 448 224 128 64 32 28 2 1 1 4 — 8 —
130 448 224 160 32 32 28 2 1 1 4 — 8 —
131 448 256 0 192 0 28 0 1 0 2 — 4 —
132 448 256 128 32 32 28 2 1 1 4 — 8 —
133 480 128 128 128 96 30 2 1 1 4 — 8 —
134 480 160 96 160 64 30 2 1 1 4 — 8 —
135 480 160 128 96 96 30 2 1 1 4 — 8 —
136 480 160 128 128 64 30 2 1 1 4 — 8 —
137 480 160 128 160 32 30 2 1 1 4 — 8 —
138 480 160 160 96 64 30 2 1 1 4 — 8 —
139 480 160 160 128 32 30 2 1 1 4 — 8 —
140 480 192 64 192 32 30 2 1 1 4 — 8 —
(To be continued)

INST01-210
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-220

(Continued from the preceding page)

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
(*1, *2) (*1) 16G 128 256
141 480 192 96 96 96 30 2 1 1 4 — 8 —
142 480 192 128 96 64 30 2 1 1 4 — 8 —
143 480 192 128 128 32 30 2 1 1 4 — 8 —
144 480 192 160 64 64 30 2 1 1 4 — 8 —
145 480 192 160 96 32 30 2 1 1 4 — 8 —
146 480 192 192 64 32 30 2 1 1 4 — 8 —
147 480 224 96 96 64 30 2 1 1 4 — 8 —
148 480 224 128 64 64 30 2 1 1 4 — 8 —
149 480 224 128 96 32 30 2 1 1 4 — 8 —
150 480 224 160 64 32 30 2 1 1 4 — 8 —
151 480 256 0 224 0 30 0 1 0 2 — 4 —
152 480 256 160 32 32 30 2 1 1 4 — 8 —
153 512 128 128 128 128 32 2 1 1 4 — 8 —
154 512 160 96 160 96 32 2 1 1 4 — 8 —
155 512 160 128 128 96 32 2 1 1 4 — 8 —
156 512 160 128 160 64 32 2 1 1 4 — 8 —
157 512 160 160 96 96 32 2 1 1 4 — 8 —
158 512 160 160 128 64 32 2 1 1 4 — 8 —
159 512 160 160 160 32 32 2 1 1 4 — 8 —
160 512 192 64 192 64 32 2 1 1 4 — 8 —
161 512 192 96 192 32 32 2 1 1 4 — 8 —
162 512 192 128 96 96 32 2 1 1 4 — 8 —
163 512 192 128 128 64 32 2 1 1 4 — 8 —
164 512 192 160 96 64 32 2 1 1 4 — 8 —
165 512 192 160 128 32 32 2 1 1 4 — 8 —
166 512 192 192 64 64 32 2 1 1 4 — 8 —
167 512 192 192 96 32 32 2 1 1 4 — 8 —
168 512 224 32 224 32 32 2 1 1 4 — 8 —
169 512 224 96 96 96 32 2 1 1 4 — 8 —
170 512 224 128 96 64 32 2 1 1 4 — 8 —
171 512 224 128 128 32 32 2 1 1 4 — 8 —
172 512 224 160 64 64 32 2 1 1 4 — 8 —
173 512 224 160 96 32 32 2 1 1 4 — 8 —
174 512 224 224 32 32 32 2 1 1 4 — 8 —
175 512 256 0 256 0 32 0 1 0 2 — 4 —
(To be continued)

INST01-220
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-230

(Continued from the preceding page)

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
(*1, *2) (*1) 16G 128 256
176 512 256 192 32 32 32 2 1 1 4 — 8 —
177 544 160 128 128 128 34 2 1 1 4 — 8 —
178 544 160 128 160 96 34 2 1 1 4 — 8 —
179 544 160 160 128 96 34 2 1 1 4 — 8 —
180 544 160 160 160 64 34 2 1 1 4 — 8 —
181 544 192 96 192 64 34 2 1 1 4 — 8 —
182 544 192 128 128 96 34 2 1 1 4 — 8 —
183 544 192 128 192 32 34 2 1 1 4 — 8 —
184 544 192 160 96 96 34 2 1 1 4 — 8 —
185 544 192 160 128 64 34 2 1 1 4 — 8 —
186 544 192 160 160 32 34 2 1 1 4 — 8 —
187 544 192 192 96 64 34 2 1 1 4 — 8 —
188 544 192 192 128 32 34 2 1 1 4 — 8 —
189 544 224 64 224 32 34 2 1 1 4 — 8 —
190 544 224 128 96 96 34 2 1 1 4 — 8 —
191 544 224 128 128 64 34 2 1 1 4 — 8 —
192 544 224 160 96 64 34 2 1 1 4 — 8 —
193 544 224 160 128 32 34 2 1 1 4 — 8 —
194 544 224 224 64 32 34 2 1 1 4 — 8 —
195 544 256 224 32 32 34 2 1 1 4 — 8 —
196 576 160 128 160 128 36 2 1 1 4 — 8 —
197 576 160 160 128 128 36 2 1 1 4 — 8 —
198 576 160 160 160 96 36 2 1 1 4 — 8 —
199 576 192 96 192 96 36 2 1 1 4 — 8 —
200 576 192 128 128 128 36 2 1 1 4 — 8 —
201 576 192 128 192 64 36 2 1 1 4 — 8 —
202 576 192 160 128 96 36 2 1 1 4 — 8 —
203 576 192 160 160 64 36 2 1 1 4 — 8 —
204 576 192 160 192 32 36 2 1 1 4 — 8 —
205 576 192 160 192 32 36 2 1 1 4 — 8 —
206 576 192 192 96 96 36 2 1 1 4 — 8 —
207 576 192 192 128 64 36 2 1 1 4 — 8 —
208 576 192 192 160 32 36 2 1 1 4 — 8 —
209 576 224 64 224 64 36 2 1 1 4 — 8 —
210 576 224 96 224 32 36 2 1 1 4 — 8 —
(To be continued)

INST01-230
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-240

(Continued from the preceding page)

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
(*1, *2) (*1) 16G 128 256
211 576 224 128 128 96 36 2 1 1 4 — 8 —
212 576 224 160 96 96 36 2 1 1 4 — 8 —
213 576 224 160 128 64 36 2 1 1 4 — 8 —
214 576 224 160 160 32 36 2 1 1 4 — 8 —
215 576 224 224 96 32 36 2 1 1 4 — 8 —
216 576 256 32 256 32 36 2 1 1 4 — 8 —
217 576 256 256 32 32 36 2 1 1 4 — 8 —
218 608 160 160 160 128 38 2 1 1 4 — 8 —
219 608 192 128 192 96 38 2 1 1 4 — 8 —
220 608 192 160 128 128 38 2 1 1 4 — 8 —
221 608 192 160 160 96 38 2 1 1 4 — 8 —
222 608 192 160 192 64 38 2 1 1 4 — 8 —
223 608 192 192 128 96 38 2 1 1 4 — 8 —
224 608 192 192 160 64 38 2 1 1 4 — 8 —
225 608 192 192 192 32 38 2 1 1 4 — 8 —
226 608 224 96 224 64 38 2 1 1 4 — 8 —
227 608 224 128 128 128 38 2 1 1 4 — 8 —
228 608 224 128 224 32 38 2 1 1 4 — 8 —
229 608 224 160 128 96 38 2 1 1 4 — 8 —
230 608 224 160 160 64 38 2 1 1 4 — 8 —
231 608 224 224 96 64 38 2 1 1 4 — 8 —
232 608 224 224 128 32 38 2 1 1 4 — 8 —
233 608 256 64 256 32 38 2 1 1 4 — 8 —
234 608 256 256 64 32 38 2 1 1 4 — 8 —
235 640 160 160 160 160 40 2 1 1 4 — 8 —
236 640 192 128 192 128 40 2 1 1 4 — 8 —
237 640 192 160 160 128 40 2 1 1 4 — 8 —
238 640 192 160 192 96 40 2 1 1 4 — 8 —
239 640 192 192 128 128 40 2 1 1 4 — 8 —
240 640 192 192 160 96 40 2 1 1 4 — 8 —
241 640 192 192 192 64 40 2 1 1 4 — 8 —
242 640 224 96 224 96 40 2 1 1 4 — 8 —
243 640 224 128 224 64 40 2 1 1 4 — 8 —
244 640 224 160 128 128 40 2 1 1 4 — 8 —
245 640 224 160 160 96 40 2 1 1 4 — 8 —
(To be continued)

INST01-240
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-250

(Continued from the preceding page)

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
(*1, *2) (*1) 16G 128 256
246 640 224 160 224 32 40 2 1 1 4 — 8 —
247 640 224 192 192 32 40 2 1 1 4 — 8 —
248 640 224 224 96 96 40 2 1 1 4 — 8 —
249 640 224 224 128 64 40 2 1 1 4 — 8 —
250 640 224 224 160 32 40 2 1 1 4 — 8 —
251 640 256 64 256 64 40 2 1 1 4 — 8 —
252 640 256 96 256 32 40 2 1 1 4 — 8 —
253 640 256 256 96 32 40 2 1 1 4 — 8 —
254 672 192 160 160 160 42 2 1 1 4 — 8 —
255 672 192 160 192 128 42 2 1 1 4 — 8 —
256 672 192 192 160 128 42 2 1 1 4 — 8 —
257 672 192 192 192 96 42 2 1 1 4 — 8 —
258 672 224 128 224 96 42 2 1 1 4 — 8 —
259 672 224 160 160 128 42 2 1 1 4 — 8 —
260 672 224 160 224 64 42 2 1 1 4 — 8 —
261 672 224 192 192 64 42 2 1 1 4 — 8 —
262 672 224 192 224 32 42 2 1 1 4 — 8 —
263 672 224 224 128 96 42 2 1 1 4 — 8 —
264 672 224 224 160 64 42 2 1 1 4 — 8 —
265 672 224 224 192 32 42 2 1 1 4 — 8 —
266 672 256 96 256 64 42 2 1 1 4 — 8 —
267 672 256 128 256 32 42 2 1 1 4 — 8 —
268 672 256 256 128 32 42 2 1 1 4 — 8 —
269 704 192 160 192 160 44 2 1 1 4 — 8 —
270 704 192 192 160 160 44 2 1 1 4 — 8 —
271 704 192 192 192 128 44 2 1 1 4 — 8 —
272 704 224 128 224 128 44 2 1 1 4 — 8 —
273 704 224 160 160 160 44 2 1 1 4 — 8 —
274 704 224 160 224 96 44 2 1 1 4 — 8 —
275 704 224 192 192 96 44 2 1 1 4 — 8 —
276 704 224 192 224 64 44 2 1 1 4 — 8 —
277 704 224 224 128 128 44 2 1 1 4 — 8 —
278 704 224 224 160 96 44 2 1 1 4 — 8 —
279 704 224 224 192 64 44 2 1 1 4 — 8 —
280 704 224 224 224 32 44 2 1 1 4 — 8 —
(To be continued)

INST01-250
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-260

(Continued from the preceding page)

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
(*1, *2) (*1) 16G 128 256
281 704 256 96 256 96 44 2 1 1 4 — 8 —
282 704 256 128 256 64 44 2 1 1 4 — 8 —
283 704 256 160 256 32 44 2 1 1 4 — 8 —
284 704 256 256 160 32 44 2 1 1 4 — 8 —
285 736 192 192 192 160 46 2 1 1 4 — 8 —
286 736 224 160 224 128 46 2 1 1 4 — 8 —
287 736 224 192 192 128 46 2 1 1 4 — 8 —
288 736 224 192 224 96 46 2 1 1 4 — 8 —
289 736 224 224 160 128 46 2 1 1 4 — 8 —
290 736 224 224 192 96 46 2 1 1 4 — 8 —
291 736 224 224 224 64 46 2 1 1 4 — 8 —
292 736 256 128 256 96 46 2 1 1 4 — 8 —
293 736 256 160 256 64 46 2 1 1 4 — 8 —
294 736 256 192 256 32 46 2 1 1 4 — 8 —
295 736 256 256 192 32 46 2 1 1 4 — 8 —
296 768 192 192 192 192 48 2 1 1 4 — 8 —
297 768 224 160 224 160 48 2 1 1 4 — 8 —
298 768 224 192 192 160 48 2 1 1 4 — 8 —
299 768 224 192 224 128 48 2 1 1 4 — 8 —
300 768 224 224 160 160 48 2 1 1 4 — 8 —
301 768 224 224 192 128 48 2 1 1 4 — 8 —
302 768 224 224 224 96 48 2 1 1 4 — 8 —
303 768 256 128 256 128 48 2 1 1 4 — 8 —
304 768 256 160 256 96 48 2 1 1 4 — 8 —
305 768 256 192 256 64 48 2 1 1 4 — 8 —
306 768 256 224 256 32 48 2 1 1 4 — 8 —
307 768 256 256 224 32 48 2 1 1 4 — 8 —
308 800 224 192 192 192 50 2 1 1 4 — 8 —
309 800 224 192 224 160 50 2 1 1 4 — 8 —
310 800 224 224 192 160 50 2 1 1 4 — 8 —
311 800 224 224 224 128 50 2 1 1 4 — 8 —
312 800 256 160 256 128 50 2 1 1 4 — 8 —
313 800 256 192 256 96 50 2 1 1 4 — 8 —
314 800 256 224 256 64 50 2 1 1 4 — 8 —
315 800 256 256 256 32 50 2 1 1 4 — 8 —
(To be continued)

INST01-260
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-270

(Continued from the preceding page)

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
(*1, *2) (*1) 16G 128 256
316 832 224 192 224 192 52 2 1 1 4 — 8 —
317 832 224 224 192 192 52 2 1 1 4 — 8 —
318 832 224 224 224 160 52 2 1 1 4 — 8 —
319 832 256 160 256 160 52 2 1 1 4 — 8 —
320 832 256 192 256 128 52 2 1 1 4 — 8 —
321 832 256 224 256 96 52 2 1 1 4 — 8 —
322 832 256 256 256 64 52 2 1 1 4 — 8 —
323 864 224 224 224 192 54 2 1 1 4 — 8 —
324 864 256 192 256 160 54 2 1 1 4 — 8 —
325 864 256 224 256 128 54 2 1 1 4 — 8 —
326 864 256 256 256 96 54 2 1 1 4 — 8 —
327 896 224 224 224 224 56 2 1 1 4 — 8 —
328 896 256 192 256 192 56 2 1 1 4 — 8 —
329 896 256 224 256 160 56 2 1 1 4 — 8 —
330 896 256 256 256 128 56 2 1 1 4 — 8 —
331 928 256 224 256 192 58 2 1 1 4 — 8 —
332 928 256 256 256 160 58 2 1 1 4 — 8 —
333 960 256 224 256 224 60 2 1 1 4 — 8 —
334 960 256 256 256 192 60 2 1 1 4 — 8 —
335 992 256 256 256 224 62 2 1 1 4 — 8 —
336 1024 256 256 256 256 64 2 1 1 4 — 8 —

*1: Standard equipment.

*2: The required SM capacity shown in Table 6.1-1 (INST06-10) must be installed in CPEX-
0.

INST01-270
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-280

Table 1.1.2.2-6 Cache Memory Upgrade Table 

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
(*1, *2) (*1) 32G 128 256
1 128 64 0 64 0 4 0 1 0 2 0 4 0
2 192 128 0 64 0 6 0 1 0 2 0 4 0
3 256 64 64 64 64 8 2 1 1 4 0 8 0
4 256 128 0 128 0 8 0 1 0 2 0 4 0
5 256 192 0 64 0 8 0 1 0 2 0 4 0
6 320 128 64 64 64 10 2 1 1 4 0 8 0
7 320 192 0 128 0 10 0 1 0 2 0 4 0
8 320 256 0 64 0 10 0 1 0 2 0 4 0
9 384 128 64 128 64 12 2 1 1 4 0 8 0
10 384 128 128 64 64 12 2 1 1 4 0 8 0
11 384 192 0 192 0 12 0 1 0 2 0 4 0
12 384 192 64 64 64 12 2 1 1 4 0 8 0
13 384 256 0 128 0 12 0 1 0 2 0 4 0
14 384 320 0 64 0 12 0 1 0 1 1 2 2
15 448 128 128 128 64 14 2 1 1 4 0 8 0
16 448 192 128 64 64 14 2 1 1 4 0 8 0
17 448 256 64 64 64 14 2 1 1 4 0 8 0
18 448 320 0 128 0 14 0 1 0 1 1 2 2
19 448 384 0 64 0 14 0 1 0 1 1 2 2
20 512 128 128 128 128 16 2 1 1 4 0 8 0
21 512 192 64 192 64 16 2 1 1 4 0 8 0
22 512 192 128 128 64 16 2 1 1 4 0 8 0
23 512 192 192 64 64 16 2 1 1 4 0 8 0
24 512 256 0 256 0 16 0 1 0 2 0 4 0
25 512 256 128 64 64 16 2 1 1 4 0 8 0
26 512 320 0 192 0 16 0 1 0 1 1 2 2
27 512 320 64 64 64 16 2 1 1 3 1 6 2
28 512 384 0 128 0 16 0 1 0 1 1 2 2
29 512 448 0 64 0 16 0 1 0 1 1 2 2
30 576 192 128 128 128 18 2 1 1 4 0 8 0
31 576 192 128 192 64 18 2 1 1 4 0 8 0
32 576 192 192 128 64 18 2 1 1 4 0 8 0
33 576 256 128 128 64 18 2 1 1 4 0 8 0
34 576 256 192 64 64 18 2 1 1 4 0 8 0
35 576 320 0 256 0 18 0 1 0 1 1 2 2
(To be continued)

INST01-280
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-290

(Continued from the preceding page)

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
(*1, *2) (*1) 32G 128 256
36 576 320 128 64 64 18 2 1 1 3 1 6 2
37 576 384 0 192 0 18 0 1 0 1 1 2 2
38 576 384 64 64 64 18 2 1 1 3 1 6 2
39 576 448 0 128 0 18 0 1 0 1 1 2 2
40 576 512 0 64 0 18 0 1 0 1 1 2 2
41 640 192 128 192 128 20 2 1 1 4 0 8 0
42 640 192 192 128 128 20 2 1 1 4 0 8 0
43 640 192 192 192 64 20 2 1 1 4 0 8 0
44 640 256 64 256 64 20 2 1 1 4 0 8 0
45 640 256 128 128 128 20 2 1 1 4 0 8 0
46 640 256 192 128 64 20 2 1 1 4 0 8 0
47 640 256 256 64 64 20 2 1 1 4 0 8 0
48 640 320 0 320 0 20 0 1 0 0 2 0 4
49 640 320 128 128 64 20 2 1 1 3 1 6 2
50 640 320 192 64 64 20 2 1 1 3 1 6 2
51 640 384 0 256 0 20 0 1 0 1 1 2 2
52 640 384 128 64 64 20 2 1 1 3 1 6 2
53 640 448 0 192 0 20 0 1 0 1 1 2 2
54 640 448 64 64 64 20 2 1 1 3 1 6 2
55 640 512 0 128 0 20 0 1 0 1 1 2 2
56 704 192 192 192 128 22 2 1 1 4 0 8 0
57 704 256 128 256 64 22 2 1 1 4 0 8 0
58 704 256 192 128 128 22 2 1 1 4 0 8 0
59 704 256 192 192 64 22 2 1 1 4 0 8 0
60 704 256 256 128 64 22 2 1 1 4 0 8 0
61 704 320 128 128 128 22 2 1 1 3 1 6 2
62 704 320 192 128 64 22 2 1 1 3 1 6 2
63 704 320 256 64 64 22 2 1 1 3 1 6 2
64 704 384 0 320 0 22 0 1 0 0 2 0 4
65 704 384 128 128 64 22 2 1 1 3 1 6 2
66 704 384 192 64 64 22 2 1 1 3 1 6 2
67 704 448 0 256 0 22 0 1 0 1 1 2 2
68 704 448 128 64 64 22 2 1 1 3 1 6 2
69 704 512 0 192 0 22 0 1 0 1 1 2 2
70 704 512 64 64 64 22 2 1 1 3 1 6 2
(To be continued)

INST01-290
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-300

(Continued from the preceding page)

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
(*1, *2) (*1) 32G 128 256
71 768 192 192 192 192 24 2 1 1 4 0 8 0
72 768 256 128 256 128 24 2 1 1 4 0 8 0
73 768 256 192 192 128 24 2 1 1 4 0 8 0
74 768 256 192 256 64 24 2 1 1 4 0 8 0
75 768 256 256 128 128 24 2 1 1 4 0 8 0
76 768 256 256 192 64 24 2 1 1 4 0 8 0
77 768 320 64 320 64 24 2 1 1 2 2 4 4
78 768 320 192 128 128 24 2 1 1 3 1 6 2
79 768 320 192 192 64 24 2 1 1 3 1 6 2
80 768 320 256 128 64 24 2 1 1 3 1 6 2
81 768 320 320 64 64 24 2 1 1 2 2 4 4
82 768 384 0 384 0 24 0 1 0 0 2 0 4
83 768 384 128 128 128 24 2 1 1 3 1 6 2
84 768 384 192 128 64 24 2 1 1 3 1 6 2
85 768 384 256 64 64 24 2 1 1 3 1 6 2
86 768 448 0 320 0 24 0 1 0 0 2 0 4
87 768 448 128 128 64 24 2 1 1 3 1 6 2
88 768 448 192 64 64 24 2 1 1 3 1 6 2
89 768 512 0 256 0 24 0 1 0 1 1 2 2
90 768 512 128 64 64 24 2 1 1 3 1 6 2
91 832 256 192 192 192 26 2 1 1 4 0 8 0
92 832 256 192 256 128 26 2 1 1 4 0 8 0
93 832 256 256 192 128 26 2 1 1 4 0 8 0
94 832 256 256 256 64 26 2 1 1 4 0 8 0
95 832 320 128 320 64 26 2 1 1 2 2 4 4
96 832 320 192 192 128 26 2 1 1 3 1 6 2
97 832 320 256 128 128 26 2 1 1 3 1 6 2
98 832 320 256 192 64 26 2 1 1 3 1 6 2
99 832 320 320 128 64 26 2 1 1 2 2 4 4
100 832 384 192 128 128 26 2 1 1 3 1 6 2
101 832 384 192 192 64 26 2 1 1 3 1 6 2
102 832 384 256 128 64 26 2 1 1 3 1 6 2
103 832 384 320 64 64 26 2 1 1 2 2 4 4
104 832 448 0 384 0 26 0 1 0 0 2 0 4
105 832 448 128 128 128 26 2 1 1 3 1 6 2
(To be continued)

INST01-300
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-310

(Continued from the preceding page)

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
(*1, *2) (*1) 32G 128 256
106 832 448 192 128 64 26 2 1 1 3 1 6 2
107 832 448 256 64 64 26 2 1 1 3 1 6 2
108 832 512 0 320 0 26 0 1 0 0 2 0 4
109 832 512 192 64 64 26 2 1 1 3 1 6 2
110 896 256 192 256 192 28 2 1 1 4 0 8 0
111 896 256 256 192 192 28 2 1 1 4 0 8 0
112 896 256 256 256 128 28 2 1 1 4 0 8 0
113 896 320 128 320 128 28 2 1 1 2 2 4 4
114 896 320 192 192 192 28 2 1 1 3 1 6 2
115 896 320 192 320 64 28 2 1 1 2 2 4 4
116 896 320 256 192 128 28 2 1 1 3 1 6 2
117 896 320 256 256 64 28 2 1 1 3 1 6 2
118 896 320 320 128 128 28 2 1 1 2 2 4 4
119 896 320 320 192 64 28 2 1 1 2 2 4 4
120 896 384 64 384 64 28 2 1 1 2 2 4 4
121 896 384 192 192 128 28 2 1 1 3 1 6 2
122 896 384 256 128 128 28 2 1 1 3 1 6 2
123 896 384 256 192 64 28 2 1 1 3 1 6 2
124 896 384 320 128 64 28 2 1 1 2 2 4 4
125 896 384 384 64 64 28 2 1 1 2 2 4 4
126 896 448 0 448 0 28 0 1 0 0 2 0 4
127 896 448 192 128 128 28 2 1 1 3 1 6 2
128 896 448 192 192 64 28 2 1 1 3 1 6 2
129 896 448 256 128 64 28 2 1 1 3 1 6 2
130 896 448 320 64 64 28 2 1 1 2 2 4 4
131 896 512 0 384 0 28 0 1 0 0 2 0 4
132 896 512 256 64 64 28 2 1 1 3 1 6 2
133 960 256 256 256 192 30 2 1 1 4 0 8 0
134 960 320 192 320 128 30 2 1 1 2 2 4 4
135 960 320 256 192 192 30 2 1 1 3 1 6 2
136 960 320 256 256 128 30 2 1 1 3 1 6 2
137 960 320 256 320 64 30 2 1 1 2 2 4 4
138 960 320 320 192 128 30 2 1 1 2 2 4 4
139 960 320 320 256 64 30 2 1 1 2 2 4 4
140 960 384 128 384 64 30 2 1 1 2 2 4 4
(To be continued)

INST01-310
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-320

(Continued from the preceding page)

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
(*1, *2) (*1) 32G 128 256
141 960 384 192 192 192 30 2 1 1 3 1 6 2
142 960 384 256 192 128 30 2 1 1 3 1 6 2
143 960 384 256 256 64 30 2 1 1 3 1 6 2
144 960 384 320 128 128 30 2 1 1 2 2 4 4
145 960 384 320 192 64 30 2 1 1 2 2 4 4
146 960 384 384 128 64 30 2 1 1 2 2 4 4
147 960 448 192 192 128 30 2 1 1 3 1 6 2
148 960 448 256 128 128 30 2 1 1 3 1 6 2
149 960 448 256 192 64 30 2 1 1 3 1 6 2
150 960 448 320 128 64 30 2 1 1 2 2 4 4
151 960 512 0 448 0 30 0 1 0 0 2 0 4
152 960 512 320 64 64 30 2 1 1 2 2 4 4
153 1024 256 256 256 256 32 2 1 1 4 0 8 0
154 1024 320 192 320 192 32 2 1 1 2 2 4 4
155 1024 320 256 256 192 32 2 1 1 3 1 6 2
156 1024 320 256 320 128 32 2 1 1 2 2 4 4
157 1024 320 320 192 192 32 2 1 1 2 2 4 4
158 1024 320 320 256 128 32 2 1 1 2 2 4 4
159 1024 320 320 320 64 32 2 1 1 1 3 2 6
160 1024 384 128 384 128 32 2 1 1 2 2 4 4
161 1024 384 192 384 64 32 2 1 1 2 2 4 4
162 1024 384 256 192 192 32 2 1 1 3 1 6 2
163 1024 384 256 256 128 32 2 1 1 3 1 6 2
164 1024 384 320 192 128 32 2 1 1 2 2 4 4
165 1024 384 320 256 64 32 2 1 1 2 2 4 4
166 1024 384 384 128 128 32 2 1 1 2 2 4 4
167 1024 384 384 192 64 32 2 1 1 2 2 4 4
168 1024 448 64 448 64 32 2 1 1 2 2 4 4
169 1024 448 192 192 192 32 2 1 1 3 1 6 2
170 1024 448 256 192 128 32 2 1 1 3 1 6 2
171 1024 448 256 256 64 32 2 1 1 3 1 6 2
172 1024 448 320 128 128 32 2 1 1 2 2 4 4
173 1024 448 320 192 64 32 2 1 1 2 2 4 4
174 1024 448 448 64 64 32 2 1 1 2 2 4 4
175 1024 512 0 512 0 32 0 1 0 0 2 0 4
(To be continued)

INST01-320
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-330

(Continued from the preceding page)

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
(*1, *2) (*1) 32G 128 256
176 1024 512 384 64 64 32 2 1 1 2 2 4 4
177 1088 320 256 256 256 34 2 1 1 3 1 6 2
178 1088 320 256 320 192 34 2 1 1 2 2 4 4
179 1088 320 320 256 192 34 2 1 1 2 2 4 4
180 1088 320 320 320 128 34 2 1 1 1 3 2 6
181 1088 384 192 384 128 34 2 1 1 2 2 4 4
182 1088 384 256 256 192 34 2 1 1 3 1 6 2
183 1088 384 256 384 64 34 2 1 1 2 2 4 4
184 1088 384 320 192 192 34 2 1 1 2 2 4 4
185 1088 384 320 256 128 34 2 1 1 2 2 4 4
186 1088 384 320 320 64 34 2 1 1 1 3 2 6
187 1088 384 384 192 128 34 2 1 1 2 2 4 4
188 1088 384 384 256 64 34 2 1 1 2 2 4 4
189 1088 448 128 448 64 34 2 1 1 2 2 4 4
190 1088 448 256 192 192 34 2 1 1 3 1 6 2
191 1088 448 256 256 128 34 2 1 1 3 1 6 2
192 1088 448 320 192 128 34 2 1 1 2 2 4 4
193 1088 448 320 256 64 34 2 1 1 2 2 4 4
194 1088 448 448 128 64 34 2 1 1 2 2 4 4
195 1088 512 448 64 64 34 2 1 1 2 2 4 4
196 1152 320 256 320 256 36 2 1 1 2 2 4 4
197 1152 320 320 256 256 36 2 1 1 2 2 4 4
198 1152 320 320 320 192 36 2 1 1 1 3 2 6
199 1152 384 192 384 192 36 2 1 1 2 2 4 4
200 1152 384 256 256 256 36 2 1 1 3 1 6 2
201 1152 384 256 384 128 36 2 1 1 2 2 4 4
202 1152 384 320 256 192 36 2 1 1 2 2 4 4
203 1152 384 320 320 128 36 2 1 1 1 3 2 6
204 1152 384 320 384 64 36 2 1 1 1 3 2 6
205 1152 384 320 384 64 36 2 1 1 1 3 2 6
206 1152 384 384 192 192 36 2 1 1 2 2 4 4
207 1152 384 384 256 128 36 2 1 1 2 2 4 4
208 1152 384 384 320 64 36 2 1 1 1 3 2 6
209 1152 448 128 448 128 36 2 1 1 2 2 4 4
210 1152 448 192 448 64 36 2 1 1 2 2 4 4
(To be continued)

INST01-330
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-340

(Continued from the preceding page)

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
(*1, *2) (*1) 32G 128 256
211 1152 448 256 256 192 36 2 1 1 3 1 6 2
212 1152 448 320 192 192 36 2 1 1 2 2 4 4
213 1152 448 320 256 128 36 2 1 1 2 2 4 4
214 1152 448 320 320 64 36 2 1 1 1 3 2 6
215 1152 448 448 192 64 36 2 1 1 2 2 4 4
216 1152 512 64 512 64 36 2 1 1 2 2 4 4
217 1152 512 512 64 64 36 2 1 1 2 2 4 4
218 1216 320 320 320 256 38 2 1 1 1 3 2 6
219 1216 384 256 384 192 38 2 1 1 2 2 4 4
220 1216 384 320 256 256 38 2 1 1 2 2 4 4
221 1216 384 320 320 192 38 2 1 1 1 3 2 6
222 1216 384 320 384 128 38 2 1 1 1 3 2 6
223 1216 384 384 256 192 38 2 1 1 2 2 4 4
224 1216 384 384 320 128 38 2 1 1 1 3 2 6
225 1216 384 384 384 64 38 2 1 1 1 3 2 6
226 1216 448 192 448 128 38 2 1 1 2 2 4 4
227 1216 448 256 256 256 38 2 1 1 3 1 6 2
228 1216 448 256 448 64 38 2 1 1 2 2 4 4
229 1216 448 320 256 192 38 2 1 1 2 2 4 4
230 1216 448 320 320 128 38 2 1 1 1 3 2 6
231 1216 448 448 192 128 38 2 1 1 2 2 4 4
232 1216 448 448 256 64 38 2 1 1 2 2 4 4
233 1216 512 128 512 64 38 2 1 1 2 2 4 4
234 1216 512 512 128 64 38 2 1 1 2 2 4 4
235 1280 320 320 320 320 40 2 1 1 0 4 0 8
236 1280 384 256 384 256 40 2 1 1 2 2 4 4
237 1280 384 320 320 256 40 2 1 1 1 3 2 6
238 1280 384 320 384 192 40 2 1 1 1 3 2 6
239 1280 384 384 256 256 40 2 1 1 2 2 4 4
240 1280 384 384 320 192 40 2 1 1 1 3 2 6
241 1280 384 384 384 128 40 2 1 1 1 3 2 6
242 1280 448 192 448 192 40 2 1 1 2 2 4 4
243 1280 448 256 448 128 40 2 1 1 2 2 4 4
244 1280 448 320 256 256 40 2 1 1 2 2 4 4
245 1280 448 320 320 192 40 2 1 1 1 3 2 6
(To be continued)

INST01-340
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-350

(Continued from the preceding page)

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
(*1, *2) (*1) 32G 128 256
246 1280 448 320 448 64 40 2 1 1 1 3 2 6
247 1280 448 384 384 64 40 2 1 1 1 3 2 6
248 1280 448 448 192 192 40 2 1 1 2 2 4 4
249 1280 448 448 256 128 40 2 1 1 2 2 4 4
250 1280 448 448 320 64 40 2 1 1 1 3 2 6
251 1280 512 128 512 128 40 2 1 1 2 2 4 4
252 1280 512 192 512 64 40 2 1 1 2 2 4 4
253 1280 512 512 192 64 40 2 1 1 2 2 4 4
254 1344 384 320 320 320 42 2 1 1 0 4 0 8
255 1344 384 320 384 256 42 2 1 1 1 3 2 6
256 1344 384 384 320 256 42 2 1 1 1 3 2 6
257 1344 384 384 384 192 42 2 1 1 1 3 2 6
258 1344 448 256 448 192 42 2 1 1 2 2 4 4
259 1344 448 320 320 256 42 2 1 1 1 3 2 6
260 1344 448 320 448 128 42 2 1 1 1 3 2 6
261 1344 448 384 384 128 42 2 1 1 1 3 2 6
262 1344 448 384 448 64 42 2 1 1 1 3 2 6
263 1344 448 448 256 192 42 2 1 1 2 2 4 4
264 1344 448 448 320 128 42 2 1 1 1 3 2 6
265 1344 448 448 384 64 42 2 1 1 1 3 2 6
266 1344 512 192 512 128 42 2 1 1 2 2 4 4
267 1344 512 256 512 64 42 2 1 1 2 2 4 4
268 1344 512 512 256 64 42 2 1 1 2 2 4 4
269 1408 384 320 384 320 44 2 1 1 0 4 0 8
270 1408 384 384 320 320 44 2 1 1 0 4 0 8
271 1408 384 384 384 256 44 2 1 1 1 3 2 6
272 1408 448 256 448 256 44 2 1 1 2 2 4 4
273 1408 448 320 320 320 44 2 1 1 0 4 0 8
274 1408 448 320 448 192 44 2 1 1 1 3 2 6
275 1408 448 384 384 192 44 2 1 1 1 3 2 6
276 1408 448 384 448 128 44 2 1 1 1 3 2 6
277 1408 448 448 256 256 44 2 1 1 2 2 4 4
278 1408 448 448 320 192 44 2 1 1 1 3 2 6
279 1408 448 448 384 128 44 2 1 1 1 3 2 6
280 1408 448 448 448 64 44 2 1 1 1 3 2 6
(To be continued)

INST01-350
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-360

(Continued from the preceding page)

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
(*1, *2) (*1) 32G 128 256
281 1408 512 192 512 192 44 2 1 1 2 2 4 4
282 1408 512 256 512 128 44 2 1 1 2 2 4 4
283 1408 512 320 512 64 44 2 1 1 1 3 2 6
284 1408 512 512 320 64 44 2 1 1 1 3 2 6
285 1472 384 384 384 320 46 2 1 1 0 4 0 8
286 1472 448 320 448 256 46 2 1 1 1 3 2 6
287 1472 448 384 384 256 46 2 1 1 1 3 2 6
288 1472 448 384 448 192 46 2 1 1 1 3 2 6
289 1472 448 448 320 256 46 2 1 1 1 3 2 6
290 1472 448 448 384 192 46 2 1 1 1 3 2 6
291 1472 448 448 448 128 46 2 1 1 1 3 2 6
292 1472 512 256 512 192 46 2 1 1 2 2 4 4
293 1472 512 320 512 128 46 2 1 1 1 3 2 6
294 1472 512 384 512 64 46 2 1 1 1 3 2 6
295 1472 512 512 384 64 46 2 1 1 1 3 2 6
296 1536 384 384 384 384 48 2 1 1 0 4 0 8
297 1536 448 320 448 320 48 2 1 1 0 4 0 8
298 1536 448 384 384 320 48 2 1 1 0 4 0 8
299 1536 448 384 448 256 48 2 1 1 1 3 2 6
300 1536 448 448 320 320 48 2 1 1 0 4 0 8
301 1536 448 448 384 256 48 2 1 1 1 3 2 6
302 1536 448 448 448 192 48 2 1 1 1 3 2 6
303 1536 512 256 512 256 48 2 1 1 2 2 4 4
304 1536 512 320 512 192 48 2 1 1 1 3 2 6
305 1536 512 384 512 128 48 2 1 1 1 3 2 6
306 1536 512 448 512 64 48 2 1 1 1 3 2 6
307 1536 512 512 448 64 48 2 1 1 1 3 2 6
308 1600 448 384 384 384 50 2 1 1 0 4 0 8
309 1600 448 384 448 320 50 2 1 1 0 4 0 8
310 1600 448 448 384 320 50 2 1 1 0 4 0 8
311 1600 448 448 448 256 50 2 1 1 1 3 2 6
312 1600 512 320 512 256 50 2 1 1 1 3 2 6
313 1600 512 384 512 192 50 2 1 1 1 3 2 6
314 1600 512 448 512 128 50 2 1 1 1 3 2 6
315 1600 512 512 512 64 50 2 1 1 1 3 2 6
(To be continued)

INST01-360
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-370

(Continued from the preceding page)

Cache Cache Memory Capacity (GB) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
(*1, *2) (*1) 32G 128 256
316 1664 448 384 448 384 52 2 1 1 0 4 0 8
317 1664 448 448 384 384 52 2 1 1 0 4 0 8
318 1664 448 448 448 320 52 2 1 1 0 4 0 8
319 1664 512 320 512 320 52 2 1 1 0 4 0 8
320 1664 512 384 512 256 52 2 1 1 1 3 2 6
321 1664 512 448 512 192 52 2 1 1 1 3 2 6
322 1664 512 512 512 128 52 2 1 1 1 3 2 6
323 1728 448 448 448 384 54 2 1 1 0 4 0 8
324 1728 512 384 512 320 54 2 1 1 0 4 0 8
325 1728 512 448 512 256 54 2 1 1 1 3 2 6
326 1728 512 512 512 192 54 2 1 1 1 3 2 6
327 1792 448 448 448 448 56 2 1 1 0 4 0 8
328 1792 512 384 512 384 56 2 1 1 0 4 0 8
329 1792 512 448 512 320 56 2 1 1 0 4 0 8
330 1792 512 512 512 256 56 2 1 1 1 3 2 6
331 1856 512 448 512 384 58 2 1 1 0 4 0 8
332 1856 512 512 512 320 58 2 1 1 0 4 0 8
333 1920 512 448 512 448 60 2 1 1 0 4 0 8
334 1920 512 512 512 384 60 2 1 1 0 4 0 8
335 1984 512 512 512 448 62 2 1 1 0 4 0 8
336 2048 512 512 512 512 64 2 1 1 0 4 0 8

*1: Standard equipment.

*2: The required SM capacity shown in Table 6.1-1 (INST06-10) must be installed in CPEX-
0.

INST01-370
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-380

1.1.2.3 System Configurations and RAID Group Installation Order

1.1.2.3.1 Rough Time of Installation
Rough time of RAID Group installation becomes addition of the following A, B, C, D, and E.

Table 1.1.2.3.1-1 Rough time of installation

Process Time NOTE
A Chassis setting time 90min / 1chassis
B HDD setting time 1min / 1HDD
C Micro code overhead for Path 90sec × (The number of existing chassis + number *1
initialization of increase chassis)
D Micro code over head for 20sec × (number of increase HDD) *1
HDD spin up
E LDEV Formatting time Refer to THEORY 3.5

*1: Twice time at the high performance model are possessed.

INST01-380
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-390

1.1.2.3.2 System Configurations

(1) DKC Rack Configuration
There are eleven patterns of DKC rack configurations to install chassis. Only the eleven
patterns shown below are allowed. The other patterns are not allowed.
Installing the DKU (FBX) in the free space in Pattern A-5/A-8, or the DKU (SBX/UBX) in the
free space in Pattern A-7 is not allowed due to the DKC-F810I-RK42 Rack load limitation.
When installing the SBX/UBX/FBX at the same time, the FBX should be located as near the
DKC as possible to maximize the performance of FMDs.

Fig. 1.1.2.3.2-1 DKC Rack Configuration

INST01-390
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-400

(2) DKU Rack Configuration

There are nine patterns of DKU rack configurations to install chassis. Only the nine patterns
shown below are allowed. The other patterns are not allowed.
Installing the DKU (FBX) in the free space in Pattern B-2, or the DKU (SBX/UBX) in the free
space in Pattern B-3/B-4 is not allowed due to the lack for the outlets or current capacity of the
PDUs installed in the DKC-F810I-RK42 Rack.

Fig. 1.1.2.3.2-2 DKU Rack Configuration

INST01-400
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-410

(3) Single DKC Layout

Table 1.1.2.3.2-1 Single DKC Layout-1

Number of maximum
Number of Number of drive installations
No. Rack Layout
DKC DKU 2.5-inch 3.5-inch
HDD HDD

DKU-01

A1 DKU-00 1 2 384 192

DKC-0

DKU-01

A2 DKU-00 DKU-03 1 4 768 384

DKC-0 DKU-02

DKU-01

A3 DKU-00 DKU-03 DKU-05 1 6 1152 576

DKC-0 DKU-02 DKU-04

INST01-410
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-420

Table 1.1.2.3.2-2 Single DKC Layout-2

Number of Number of maximum
DKU drive installations
Number of
No. Rack Layout 2.5- 3.5-
DKC SBX/
FBX inch inch FMD
UBX
HDD HDD

DKU-01
B1 1 0 2 0 0 96
DKU-00

DKC-0

DKU-01
B2 1 1 1 192 96 48
DKU-00

DKC-0

DKU-01
B3 DKU-03 1 2 2 384 192 96
DKU-00
DKU-02
DKC-0

DKU-01
B4 DKU-03 1 3 1 576 288 48
DKU-00
DKU-02
DKC-0

DKU-01
B5 DKU-03 DKU-05 1 4 2 768 384 96
DKU-00
DKU-02 DKU-04
DKC-0

DKU-01
B6 DKU-03 DKU-05 1 5 1 960 480 48
DKU-00
DKU-02 DKU-04
DKC-0

INST01-420
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-430

(4) Twin DKC Layout

Table 1.1.2.3.2-3 Twin DKC Layout-1

Number of maximum
Number of Number of drive installations
No. Rack Layout
DKC DKU 2.5-inch 3.5-inch
HDD HDD

DKU-11 DKU-01

C1 DKU-10 DKU-00 2 4 768 384

DKC-1 DKC-0

DKU-11 DKU-01

C2 DKU-10 DKU-00 DKU-03 2 6 1152 576

DKC-1 DKC-0 DKU-02

DKU-11 DKU-01

C3 DKU-13 DKU-10 DKU-00 DKU-03 2 8 1536 768

DKU-12 DKC-1 DKC-0 DKU-02

DKU-11 DKU-01

C4 DKU-13 DKU-10 DKU-00 DKU-03 DKU-05 2 10 1920 960

DKU-12 DKC-1 DKC-0 DKU-02 DKU-04

DKU-11 DKU-01

C5 DKU-15 DKU-13 DKU-10 DKU-00 DKU-03 DKU-05 2 12 2304 1152

DKU-14 DKU-12 DKC-1 DKC-0 DKU-02 DKU-04

INST01-430
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-440

Table 1.1.2.3.2-4 Twin DKC Layout-2

Number of Number of maximum
DKU drive installations
Number of
No. Rack Layout 2.5- 3.5-
DKC SBX/
FBX inch inch FMD
UBX
HDD HDD

DKU-11 DKU-01
D1 2 2 2 384 192 96
DKU-10 DKU-00

DKC-1 DKC-0

DKU-11 DKU-01
D2 DKU-03 2 4 2 768 384 96
DKU-10 DKU-00

DKC-1 DKC-0 DKU-02

DKU-11 DKU-01
D3 DKU-13 DKU-03 2 6 2 1152 576 96
DKU-10 DKU-00
DKU-12 DKC-1 DKC-0 DKU-02

DKU-11 DKU-01
D4 DKU-13 DKU-03 DKU-05 2 8 2 1536 768 96
DKU-10 DKU-00
DKU-12 DKC-1 DKC-0 DKU-02 DKU-04

DKU-11 DKU-01
D5 DKU-15 DKU-13 DKU-03 DKU-05 2 10 2 1920 960 96
DKU-10 DKU-00
DKU-14 DKU-12 DKC-1 DKC-0 DKU-02 DKU-04

INST01-440
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-450

Table 1.1.2.3.2-5 Twin DKC Layout-3

Number of Number of maximum
DKU drive installations
Number of
No. Rack Layout 2.5- 3.5-
DKC SBX/
FBX inch inch FMD
UBX
HDD HDD

DKU-11 DKU-01
E1 2 0 4 0 0 192
DKU-10 DKU-00

DKC-1 DKC-0

DKU-11 DKU-01
E2 DKU-03 2 2 4 384 192 192
DKU-10 DKU-00

DKC-1 DKC-0 DKU-02

DKU-11 DKU-01
E3 DKU-13 DKU-03 2 4 4 768 384 192
DKU-10 DKU-00
DKU-12 DKC-1 DKC-0 DKU-02

DKU-11 DKU-01
E4 DKU-13 DKU-03 DKU-05 2 6 4 1152 576 192
DKU-10 DKU-00
DKU-12 DKU-02 DKU-04
DKC-1 DKC-0

DKU-11 DKU-01
E5 DKU-15 DKU-13 DKU-03 DKU-05 2 8 4 1536 768 192
DKU-10 DKU-00
DKU-14 DKU-12 DKC-1 DKC-0 DKU-02 DKU-04

INST01-450
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-460

(5) Dual DKC Layout

Table 1.1.2.3.2-6 Dual DKC Layout-1

Number of Number of maximum
DKU drive installations
Number
No. Rack Layout 2.5- 3.5-
of DKC SBX/
FBX inch inch FMD
UBX
HDD HDD

DKU-10

DKC-1
F1 2 0 2 0 0 96
DKU-00

DKC-0

DKU-10

DKC-1
F2 DKU-02 2 1 3 192 96 144
DKU-00

DKC-0 DKU-01

DKU-10

DKC-1
F3 DKU-12 DKU-02 2 2 4 384 192 192
DKU-00
DKU-11 DKC-0 DKU-01

DKU-10

DKC-1
F4 DKU-04 2 4 4 768 384 192
DKU-12 DKU-02
DKU-00
DKU-11 DKC-0 DKU-01 DKU-03

DKU-10

DKC-1
F5 DKU-14 DKU-04 2 6 4 1152 576 192
DKU-12 DKU-02
DKU-00
DKU-13 DKU-11 DKC-0 DKU-01 DKU-03

DKU-10

DKC-1
F6 DKU-14 DKU-04 2 7 4 1344 672 192
DKU-12 DKU-02
DKU-00
DKU-13 DKU-11 DKC-0 DKU-01 DKU-03 DKU-05

DKU-10

DKC-1
F7 DKU-14 DKU-04 2 8 4 1536 768 192
DKU-12 DKU-02
DKU-00
DKU-15 DKU-13 DKU-11 DKC-0 DKU-01 DKU-03 DKU-05

INST01-460
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-470

Table 1.1.2.3.2-7 Dual DKC Layout-2

Number of Number of maximum
DKU drive installations
Number
No. Rack Layout 2.5- 3.5-
of DKC SBX/
FBX inch inch FMD
UBX
HDD HDD

DKU-10

DKU-00
G1 2 0 2 0 0 96
DKC-1

DKC-0

DKU-10

DKU-00
G2 DKU-02 2 1 3 192 96 144
DKC-1

DKC-0 DKU-01

DKU-10

DKU-00
G3 DKU-12 DKU-02 2 2 4 384 192 192
DKC-1

DKU-11 DKC-0 DKU-01

DKU-10

DKU-00
G4 DKU-04 2 4 4 768 384 192
DKU-12 DKC-1 DKU-02

DKU-11 DKC-0 DKU-01 DKU-03

DKU-10

DKU-00
G5 DKU-14 DKU-04 2 6 4 1152 576 192
DKU-12 DKC-1 DKU-02

DKU-13 DKU-11 DKC-0 DKU-01 DKU-03

DKU-10

DKU-00
G6 DKU-14 DKU-04 2 7 4 1344 672 192
DKU-12 DKC-1 DKU-02

DKU-13 DKU-11 DKC-0 DKU-01 DKU-03 DKU-05

DKU-10

DKU-00
G7 DKU-14 DKU-04 2 8 4 1536 768 192
DKU-12 DKC-1 DKU-02

DKU-15 DKU-13 DKU-11 DKC-0 DKU-01 DKU-03 DKU-05

INST01-470
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-480

Table 1.1.2.3.2-8 Dual DKC Layout-3

Number of Number of maximum
DKU drive installations
Number of
No. Rack Layout 2.5- 3.5-
DKC SBX/
FBX inch inch FMD
UBX
HDD HDD

DKU-00
H1 2 0 2 0 0 96
DKC-1

DKU-10 DKC-0

DKU-01

DKU-00
H2 2 0 4 0 0 192
DKU-11 DKC-1

DKU-10 DKC-0

DKU-01

DKU-12 DKU-00
H3 DKU-03 2 3 4 576 288 192
DKU-11 DKC-1

DKC-0 DKU-02
DKU-10

DKU-01

DKU-12 DKU-00
H4 DKU-14 DKU-03 2 5 4 960 480 192
DKU-11 DKC-1
DKU-13 DKU-02
DKU-10 DKC-0

DKU-01

DKU-12 DKU-00
H5 DKU-14 DKU-03 DKU-05 2 7 4 1344 672 192
DKU-11 DKC-1
DKU-13 DKC-0 DKU-02 DKU-04
DKU-10

DKU-01

DKU-12 DKU-00
H6 DKU-14 DKU-03 DKU-05 2 8 4 1536 768 192
DKU-11 DKC-1
DKU-15 DKU-13 DKU-02 DKU-04
DKU-10 DKC-0

INST01-480
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-490

1.1.2.3.3 Connection of DKA to Drive Chassis

The DKA and the Drive Chassis connections are shown below.

DKC-F810I-CC1

to HDU-017 to HDU-017

HDU-007
SSW007-1 SSW007-2

to HDU-016 to HDU-016

SSW006-1 HDU-006 SSW006-2

to HDU-015 to HDU-015
HDU-005
SSW005-1 SSW005-2

to HDU-014 to HDU-014

HDU-004
SSW004-1 SSW004-2

to HDU-013 to HDU-013

HDU-003
SSW003-1 SSW003-2

to HDU-012 to HDU-012
HDU-002
SSW002-1 SSW002-2

to HDU-011 to HDU-011
HDU-001
SSW001-1 SSW001-2

to HDU-010 to HDU-010

SSW000-1 HDU-000 SSW000-2

DKU-00

SAS Cable Max.8 paths

Cluster 1 Cluster 2
0 0
1 DKA-0 DKA-0 1
2 2
3 3

DKC

Fig. 1.1.2.3.3-1 The SAS Connections Diagram of RACK-00

(SBX/UBX Standard Model)

INST01-490
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-500

to HDU-017 to HDU-017

HDU-007
SSW007-1 SSW007-2

to HDU-016 to HDU-016

SSW006-1 HDU-006 SSW006-2

to HDU-015 to HDU-015

HDU-005
SSW005-1 SSW005-2

to HDU-014 to HDU-014

HDU-004
SSW004-1 SSW004-2

to HDU-013 to HDU-013
HDU-003
SSW003-1 SSW003-2

to HDU-012 to HDU-012
HDU-002
SSW002-1 SSW002-2

to HDU-011 to HDU-011
HDU-001
SSW001-1 SSW001-2

to HDU-010 to HDU-010

SSW000-1 HDU-000 SSW000-2

DKU-00
SAS Cable Max.8 paths

Cluster 1 Cluster 2
0 0
1 DKA-0 DKA-0 1
2 2
3 3

0 0
1 DKA-1 DKA-1 1
2 2
3 3

DKC

Fig. 1.1.2.3.3-2 The SAS Connections Diagram of RACK-00

(SBX/UBX High Performance Model)

INST01-500
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-510
DKC-F810I-CC1

to HDU-016 to HDU-017 to HDU-016 to HDU-017

HDU-007

SSW003-1 HDU-006 SSW003-2

to HDU-014 to HDU-015 to HDU-014 to HDU-015

HDU-005

SSW002-1 HDU-004 SSW002-2

to HDU-012 to HDU-013 to HDU-012 to HDU-013

HDU-003

SSW001-1 HDU-002 SSW001-2

to HDU-010 to HDU-011 to HDU-010 to HDU-011

HDU-001

SSW000-1 HDU-000 SSW000-2

DKU-00
Max.8 paths
SAS Cable

Cluster 1 Cluster 2
0 0
1 DKA-0 DKA-0 1
2 2
3 3

DKC

Fig. 1.1.2.3.3-3 The SAS Connections Diagram of RACK-00 (FBX Standard Model)

INST01-510
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-520

to HDU-016 to HDU-017 to HDU-016 to HDU-017

HDU-007

SSW003-1 HDU-006 SSW003-2

to HDU-014 to HDU-015 to HDU-014 to HDU-015

HDU-005

SSW002-1 HDU-004 SSW002-2

to HDU-012 to HDU-013 to HDU-012 to HDU-013

HDU-003

SSW001-1 HDU-002 SSW001-2

to HDU-010 to HDU-011 to HDU-010 to HDU-011

HDU-001

SSW000-1 HDU-000 SSW000-2

DKU-00
Max.16 paths
SAS Cable

Cluster 1 Cluster 2
0 0
1 DKA-0 DKA-0 1
2 2
3 3

0 0
1 DKA-1 DKA-1 1
2 2
3 3

DKC

Fig. 1.1.2.3.3-4 The SAS Connections Diagram of RACK-00

(FBX High Performance Model)

INST01-520
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-530

The installation order of the DKA and Drive Chassis is as follows.

DKA → DKU-00 → DKU-01 → DKU-02 → DKU-03 → DKU-04 → DKU-05
The relation of DKA connection to HDU in the Drive Chassis is shown below.

HDU-017
HDU-016
HDU-015
HDU-014
HDU-013
HDU-012
HDU-011
HDU-010
HDU-037 HDU-057
DKU-01
HDU-036 HDU-056
HDU-007 HDU-035 HDU-055
HDU-006 HDU-034 HDU-054
HDU-005 HDU-033 HDU-053
HDU-004 HDU-032 HDU-052
HDU-003 HDU-031 HDU-051
HDU-002 HDU-030 HDU-050
HDU-001 DKU-03 DKU-05
HDU-000
HDU-027 HDU-047
DKU-00
HDU-026 HDU-046
CL1 CL2 HDU-025 HDU-045
HDU-024 HDU-044
DKA DKA HDU-023 HDU-043
-0 -0
HDU-022 HDU-042
HDU-021 HDU-041
DKA DKA
HDU-020 HDU-040
-1 -1
DKU-02 DKU-04
DKC-0

RACK-00 RACK-01 RACK-02

Fig. 1.1.2.3.3-5 Connection Order of Drive Chassis

INST01-530
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-540

1.1.2.3.4 System Configurations and Numbers of Options Required

The required options are shown below.

Table 1.1.2.3.4-1 Requisite Options for Standard Model

(Single and Twin DKC model)
Required Number of Options
No. DKC810I DKC-F810I- 2.5-inch 3.5-inch
FMD
-CBXA CBXB RK42 SBX UBX FBX SCA CC1 CC2 CC4 MOD5 HDD HDD
(*1)
(*1) (*1)
1 1 — 1 1 — 1 1 1 — — 192 — —
2 1 — 1 2 — 1 1 3 — — 384 — —
3 1 — 2 3 — 1 1 3 2 — 576 — —
4 1 — 2 4 — 1 1 5 2 — 768 — —
5 1 — 3 5 — 1 1 5 4 — 960 — —
6 1 — 3 6 — 1 1 7 4 — 1152 — —
7 1 1 4 7 — 2 2 8 4 1 1344 — —
8 1 1 4 8 — 2 2 10 4 1 1536 — —
9 1 1 5 9 — 2 2 10 6 1 1728 — —
10 1 1 5 10 — 2 2 12 6 1 1920 — —
11 1 1 6 11 — 2 2 12 8 1 2112 — —
12 1 1 6 12 — 2 2 14 8 1 2304 — —
13 1 — 1 — 1 1 1 1 — — — 96 —
14 1 — 1 — 2 1 1 3 — — — 192 —
15 1 — 2 — 3 1 1 3 2 — — 288 —
16 1 — 2 — 4 1 1 5 2 — — 384 —
17 1 — 3 — 5 1 1 5 4 — — 480 —
18 1 — 3 — 6 1 1 7 4 — — 576 —
19 1 1 4 — 7 2 2 8 4 1 — 672 —
20 1 1 4 — 8 2 2 10 4 1 — 768 —
21 1 1 5 — 9 2 2 10 6 1 — 864 —
22 1 1 5 — 10 2 2 12 6 1 — 960 —
23 1 1 6 — 11 2 2 12 8 1 — 1056 —
24 1 1 6 — 12 2 2 14 8 1 — 1152 —
25 1 — 1 — — 1 1 1 1 — — — — 48
26 1 — 1 — — 2 1 3 1 — — — — 96
27 1 1 2 — — 3 2 4 2 — 1 — — 144
28 1 1 2 — — 4 2 6 2 — 1 — — 192

*1: The maximum number of installable HDDs/FMDs includes the spare drive(s).

INST01-540
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-550

Table 1.1.2.3.4-2 Requisite Options for Standard Model (Dual DKC model)
Required Number of Options
No. DKC810I DKC-F810I- FMD Remarks
-CBXA CBXB RK42 FBX SCA CC1 CC2 CC4 FC5 MOD5 (*1)
1 1 1 1 2 2 2 2 — — 1 96 Table 1.1.2.3.2-6 (F1)
2 1 1 2 3 2 2 2 — 2 1 144 Table 1.1.2.3.2-6 (F2)
3 1 1 3 4 2 2 2 2 2 1 192 Table 1.1.2.3.2-6 (F3)
4 1 1 1 2 2 2 — — 2 1 96 Table 1.1.2.3.2-7 (G1)
5 1 1 2 3 2 2 — — 4 1 144 Table 1.1.2.3.2-7 (G2)
6 1 1 3 4 2 2 — 2 4 1 192 Table 1.1.2.3.2-7 (G3)
7 1 1 2 2 2 2 — — 2 1 96 Table 1.1.2.3.2-8 (H1)
8 1 1 2 3 2 4 — — 2 1 144 Table 1.1.2.3.2-8 (H2)
9 1 1 2 4 2 6 — — 2 1 192 Table 1.1.2.3.2-8 (H3)

*1: The maximum number of installable FMDs includes the spare drive(s).

INST01-550
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-560

Table 1.1.2.3.4-3 Requisite Options for High Performance Model

(Single and Twin DKC model)
Required Number of Options
No. DKC810I DKC-F810I- 2.5-inch 3.5-inch
FMD
HDD HDD
-CBXA CBXB RK42 SBX UBX FBX SCA CC1 CC2 CC4 MOD5 (*1)
(*1) (*1)
1 1 — 1 1 — — 2 — 2 — — 192 — —
2 1 — 1 2 — — 2 — 4 — — 384 — —
3 1 — 2 3 — — 2 — 4 2 — 576 — —
4 1 — 2 4 — — 2 — 6 2 — 768 — —
5 1 — 2 5 — — 2 — 6 4 — 960 — —
6 1 — 3 6 — — 2 — 8 4 — 1152 — —
7 1 1 3 7 — — 4 — 10 4 1 1344 — —
8 1 1 3 8 — — 4 — 12 4 1 1536 — —
9 1 1 4 9 — — 4 — 12 6 1 1728 — —
10 1 1 4 10 — — 4 — 14 6 1 1920 — —
11 1 1 5 11 — — 4 — 14 8 1 2112 — —
12 1 1 5 12 — — 4 — 16 8 1 2304 — —
13 1 — 1 — 1 — 2 — 2 — — — 96 —
14 1 — 1 — 2 — 2 — 4 — — — 192 —
15 1 — 2 — 3 — 2 — 4 2 — — 288 —
16 1 — 2 — 4 — 2 — 6 2 — — 384 —
17 1 — 2 — 5 — 2 — 6 4 — — 480 —
18 1 — 3 — 6 — 2 — 8 4 — — 576 —
19 1 1 3 — 7 — 4 — 10 4 1 — 672 —
20 1 1 3 — 8 — 4 — 12 4 1 — 768 —
21 1 1 4 — 9 — 4 — 12 6 1 — 864 —
22 1 1 4 — 10 — 4 — 14 6 1 — 960 —
23 1 1 5 — 11 — 4 — 14 8 1 — 1056 —
24 1 1 5 — 12 — 4 — 16 8 1 — 1152 —
25 1 — 1 — — 1 2 — 2 — — — — 48
26 1 — 1 — — 2 2 2 2 — — — — 96
27 1 1 2 — — 3 4 2 4 — 1 — — 144
28 1 1 2 — — 4 4 4 4 — 1 — — 192

*1: The maximum number of installable HDDs/FMDs includes the spare drive(s).

INST01-560
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-570

Table 1.1.2.3.4-4 Requisite Options for High Performance Model (Dual DKC model)
Required Number of Options
No. DKC810I DKC-F810I- FMD Remarks
-CBXA CBXB RK42 FBX SCA CC1 CC2 CC4 FC5 MOD5 (*1)
1 1 1 1 2 4 — 4 — — 1 96 Table 1.1.2.3.2-6 (F1)
2 1 1 2 3 4 — 4 — 2 1 144 Table 1.1.2.3.2-6 (F2)
3 1 1 3 4 4 — 4 2 2 1 192 Table 1.1.2.3.2-6 (F3)
4 1 1 1 2 4 — — — 4 1 96 Table 1.1.2.3.2-7 (G1)
5 1 1 2 3 4 — — — 6 1 144 Table 1.1.2.3.2-7 (G2)
6 1 1 3 4 4 — — 2 6 1 192 Table 1.1.2.3.2-7 (G3)
7 1 1 2 2 4 — — — 4 1 96 Table 1.1.2.3.2-8 (H1)
8 1 1 2 3 4 2 — — 4 1 144 Table 1.1.2.3.2-8 (H2)
9 1 1 2 4 4 4 — — 4 1 192 Table 1.1.2.3.2-8 (H3)

*1: The maximum number of installable FMDs includes the spare drive(s).

INST01-570
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-580

(1) In case of the twin DKC configuration that uses HDDs and FMDs
The storage system configuration and the number of required options for each model are
shown below.

RACK-00 RACK-01 RACK-02

DKC-F810I DKU-01 DKC-F810I-

-SBX DKC-F810I-
CC4/FC5/FC30/FC1J
CC4/FC5/FC30/FC1J
HDU
DKC-F810I DKC-F810I-
-CC2 CC4/FC5/FC30/FC1J

DKC-F810I DKU-00
-CC2 DKU-03 DKU-05
DKC-F810I
-SBX HDU
HDU HDU
DKC-F810I
-CC2 DKC-F810I
-CC2
DKC-F810I DKA 0 DKA 1
-CC2 DKU-02 DKU-04 DKC-F810I
DKC-0 -CC2
DKC-F810I
-SCA CPEX CPEX HDU HDU
0 1
DKC810I
-CBXA
DKC-F810I-MFC5/ DKC-F810I-CPEX DKC-F810I-CC4/FC5/FC30/FC1J
MFC30/MFC1J
DKC-F810I-MOD5/
MOD30/MOD1J RACK-12 RACK-11 RACK-10

DKU-11

DKC-F810I-CC4/ DKC-F810I-CC4/
FC5/FC30/FC1J HDU
FC5/FC30/FC1J
DKC-F810I
-CC2

DKU-10 DKC-F810I
DKU15 DKU-13 -CC2

HDU
HDU HDU DKC-F810I
DKC-F810I -CC2
-CC2
DKC-F810I
DKA 2 DKA 3 -CC2
DKC-F810I
-CC2 DKU-14 DKU-12
DKC-1 DKC-F810I
HDU HDU CPEX CPEX -CBXB
2 3
DKC-F810I
-CPEX
DKC-F810I-CC4/FC5/FC30/FC1J DKC-F810I-CC4/FC5/FC30/FC1J

Fig. 1.1.2.3.4-1 Twin DKC Configurations and Required I/F Cable Options
(High Performance Model)

INST01-580
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-590

RACK-10 RACK-00

DKU-11 DKU-01 DKC-F810I-FBX

FMD FMD
DKC-F810I-CC1 DKC-F810I-CC1

DKC-F810I-CC1
DKU-10 DKU-00 DKC-F810I-CC1

DKC-F810I-FBX
FMD FMD
DKC-F810I-CC2 DKC-F810I-CC2

DKC-F810I-CC2 DKC-F810I-CC2
DKA 2 DKA 3 DKA 0 DKA 1

DKC-F810I-SCA DKC-1 DKC-0 DKC810I-CBXA

CPEX CPEX CPEX CPEX
2 3 0 1
DKC-F810I-CPEX
DKC-F810I-CBXB

DKC-F810I-CPEX

DKC-F810I-MOD5/MOD30/MOD1J DKC-F810I-MFC5/MFC30/MFC1J

Fig. 1.1.2.3.4-2 Twin DKC Configuration and Required I/F Cable Options
(FMD High Performance Model)

INST01-590
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-600

(2) In case of the single DKC configuration that uses HDDs and FMDs

RACK-00 RACK-01 RACK-02

DKC-F810I
-FBX
DKU-01 DKC-F810I-
DKC-F810I CC4/FC5/
-CC2 FC30/FC1J
FMD
DKC-F810I
-CC2
DKC-F810I DKC-F810I
-UBX/SBX DKU-00 -UBX/SBX
DKU-03 DKU-05
HDD DKC-F810I
DKC-F810I HDD HDD -CC2
-CC1
(inner connection) DKC-F810I
DKC-F810I-CC2 -CC2
DKA
0 DKU-02 DKU-04
DKC-F810I-SCA DKC-F810I
FMD HDD -UBX/SBX
DKC-0
DKC810I-CBXA

DKC-F810I-CC4/FC5/
DKC-F810I-CC4/FC5/FC30/FC1J FC30/FC1J
DKC-F810I-CC4/FC5/FC30/FC1J

Fig. 1.1.2.3.4-3 Single DKC Configurations and Required I/F Cable Options
(Standard Model)

RACK-00 RACK-01

DKC-F810I-
CC4/FC5/FC30/FC1J
DKC-F810I
-CC1 DKC-F810I-
DKC-F810I-FBX CC4/FC5/FC30/FC1J
DKU-01

FMD DKU-03 DKC-F810I

-UBX/SBX
DKC-F810I-CC1
HDD
DKU-00
DKC-F810I-CC2
DKC-F810I-FBX
FMD
DKC-F810I-CC2

DKC-F810I-CC2
DKU-02
DKA 0
DKC-F810I-SCA HDD
DKC-F810I
DKC-0 -UBX/SBX
DKC810I-CBXA DKC-F810I-CC1
(inner connection)

Fig. 1.1.2.3.4-4 Single DKC Configuration and Required I/F Cable Options
(FMD Standard Model)
INST01-600
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-610

(3) In case of the dual DKC configuration that uses HDDs and FMDs
In the case of the dual DKC configurations, DKC-F810I-FC5 cables are required for DKC-
DKU connection.
Only in the case of the configuration shown in Fig. 1.1.2.3.4-5, DKC-F810I-CC2 cables can be
used for DKC-DKU connection.

RACK-10 RACK-00 RACK-01

DKU-10
DKC-F810I-FBX

FMD
DKC-F810I-CC2 DKC-F810I-CC2

DKC-F810I-MOD5 DKC-F810I-MFC5
DKC-F810I-CC4/ DKA 2 DKA 3
FC5/FC30/FC1J
DKC-1 DKC-F810I
DKC-F810I-CC4/
FC5/FC30/FC1J CPEX CPEX -FC5/FC30/FC1J
2 3
DKC-F810I
DKC-F810I-FBX
-FC5/FC30/FC1J
DKU-00
DKC-F810I
-SBX/UBX DKU-12 DKU-02 DKC-F810I
FMD -SBX/UBX
HDD HDD
DKC-F810I DKC-F810I
-CC2 -CC2
DKA 0 DKA 1
DKC-F810I DKC-F810I
-CC2 DKU-11 DKU-01
DKC-0 -CC2
CPEX CPEX DKC-F810I
DKC-F810I FMD FMD
0 1 -FBX
-FBX

DKC-F810I-CC2 DKC-F810I-CC2

Fig. 1.1.2.3.4-5 Dual DKC Configuration and Required I/F Cable Options-1

INST01-610
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-620

RACK-10 RACK-00 RACK-01

DKU-10
DKC-F810I-FBX
DKC-F810I-CC4/
FC5/FC30/FC1J FMD DKC-F810I-FC5

DKC-F810I-FC5 DKC-F810I
-FC5/FC30/FC1J
DKU-00
DKC-F810I-CC4/ DKC-F810I
FC5/FC30/FC1J -FC5/FC30/FC1J
FMD

DKC-F810I-FC5 DKC-F810I-FC5

DKC-F810I- DKC-F810I-
DKA-2 DKA-3 SBX/UBX
SBX/UBX DKU-12 DKU-02
DKC-1
DKC-F810I- CPEX CPEX DKC-F810I-
CC2 HDD HDD
2 3 CC2

DKC-F810I- DKC-F810I-
CC2 CC2
DKA-0 DKA-1
DKU-11 DKU-01
DKC-0
DKC-F810I-
DKC-F810I- FMD CPEX CPEX FMD FBX
FBX 0 1

DKC-F810I-MOD5 DKC-F810I-MFC5

Fig. 1.1.2.3.4-6 Dual DKC Configuration and Required I/F Cable Options-2

RACK-10 RACK-00 RACK-01

DKC-F810I-CC1
DKU-01 DKC-F810I-FBX
DKC-F810I-FC5
DKC-F810I- DKC-F810I-CC1
FMD
FC5/FC30/FC1J
DKC-F810I- DKC-F810I-CC4/
FC5/FC30/FC1J FC5/FC30/FC1J
DKC-F810I- DKU-00
SBX/UBX DKU-12 DKC-F810I-CC4/
FC5/FC30/FC1J
FMD
DKC-F810I-FC5
HDD

DKC-F810I- DKU-03
CC2 DKA-2 DKA-3 DKC-F810I-
SBX/UBX
DKC-F810I- DKU-11 HDD
DKC-1
CC2
CPEX CPEX
FMD 2 3 DKC-F810I-
CC2
DKC-F810I-
CC1 DKC-F810I-
DKA-0 DKA-1 DKU-02
CC2
DKC-F810I- DKU-10
CC1 DKC-0
HDD DKC-F810I-
DKC-F810I- FMD CPEX CPEX SBX/UBX
FBX 0 1

DKC-F810I-MOD5 DKC-F810I-MFC5

Fig. 1.1.2.3.4-7 Dual DKC Configuration and Required I/F Cable Options-3

INST01-620
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-630

(4) In case of the diskless configuration

In case of the diskless configuration, two controller chassis can be installed in the same rack.

DKC-Rack DKC-Rack

Other product Other product

space space

22U

32U

42U
DKC-0/1
DKC810I-CBXA/ 10U
DKC-F810I-CBXB

DKC-0 DKC-0
DKC810I-CBXA 10U DKC810I-CBXA 10U

Fig. 1.1.2.3.4-8 Diskless System Configurations

INST01-630
DKC810I
Copyright © 2013, Hitachi, Ltd.

INST01-640
The HDDs are installed from the location of 00 to 23 in turn per HDU-box.

Fig. 1.1.2.3.5-1 HDD Installation Order to the SFF Drive Chassis

HDU-007

HDU-006

HDU-005

HDU-004

HDU-003

HDU-002

HDU-001

HDU-000
(1) Order of HDD installation in SFF Drive Chassis

7-23 6-23 5-23 4-23 3-23 2-23 1-23 0-23

7-22 6-22 5-22 4-22 3-22 2-22 1-22 0-22
7-21 6-21 5-21 4-21 3-21 2-21 1-21 0-21
7-20 6-20 5-20 4-20 3-20 2-20 1-20 0-20
7-19 6-19 5-19 4-19 3-19 2-19 1-19 0-19
7-18 6-18 5-18 4-18 3-18 2-18 1-18 0-18

SFF Drive Chassis (Front View)

1.1.2.3.5 RAID Group Installation Order

7-17 6-17 5-17 4-17 3-17 2-17 1-17 0-17

7-16 6-16 5-16 4-16 3-16 2-16 1-16 0-16
7-15 6-15 5-15 4-15 3-15 2-15 1-15 0-15
7-14 6-14 5-14 4-14 3-14 2-14 1-14 0-14
7-13 6-13 5-13 4-13 3-13 2-13 1-13 0-13
7-12 6-12 5-12 4-12 3-12 2-12 1-12 0-12
7-11 6-11 5-11 4-11 3-11 2-11 1-11 0-11
7-10 6-10 5-10 4-10 3-10 2-10 1-10 0-10
7-09 6-09 5-09 4-09 3-09 2-09 1-09 0-09
7-08 6-08 5-08 4-08 3-08 2-08 1-08 0-08
7-07 6-07 5-07 4-07 3-07 2-07 1-07 0-07
7-06 6-06 5-06 4-06 3-06 2-06 1-06 0-06
7-05 6-05 5-05 4-05 3-05 2-05 1-05 0-05
7-04 6-04 5-04 4-04 3-04 2-04 1-04 0-04
Hitachi Proprietary

7-03 6-03 5-03 4-03 3-03 2-03 1-03 0-03

Rev.0 / Dec.2013

7-02 6-02 5-02 4-02 3-02 2-02 1-02 0-02

INST01-640

7-01 6-01 5-01 4-01 3-01 2-01 1-01 0-01

7-00 6-00 5-00 4-00 3-00 2-00 1-00 0-00
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-650

(2) Order of HDD installation in LFF Drive Chassis

The HDDs are installed from the location of 00 to 11 in turn per HDU.

7-08 7-09 7-10 7-11

7-04 7-05 7-06 7-07 HDU-007
7-00 7-01 7-02 7-03

6-08 6-09 6-10 6-11

6-04 6-05 6-06 6-07 HDU-006
6-00 6-01 6-02 6-03

5-08 5-09 5-10 5-11

5-04 5-05 5-06 5-07 HDU-005
5-00 5-01 5-02 5-03

4-08 4-09 4-10 4-11

4-04 4-05 4-06 4-07 HDU-004
4-00 4-01 4-02 4-03

3-08 3-09 3-10 3-11

3-04 3-05 3-06 3-07 HDU-003
3-00 3-01 3-02 3-03

2-08 2-09 2-10 2-11

2-04 2-05 2-06 2-07 HDU-002
2-00 2-01 2-02 2-03

1-08 1-09 1-10 1-11

1-04 1-05 1-06 1-07 HDU-001
1-00 1-01 1-02 1-03

0-08 0-09 0-10 0-11

0-04 0-05 0-06 0-07 HDU-000
0-00 0-01 0-02 0-03

LFF Drive Chassis (Front View)

Fig. 1.1.2.3.5-2 HDD Installation Order to the LFF Drive Chassis

INST01-650
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-660

(3) Order of FMD installation in FMD Chassis

The FMDs are installed from the location of 00 to 05 in turn per FBX-Box.

7-03 7-04 7-05

7-00 7-01 7-02 FBX Box
6-03 6-04 6-05
6-00 6-01 6-02

5-03 5-04 5-05

5-00 5-01 5-02 FBX Box
4-03 4-04 4-05
4-00 4-01 4-02

3-03 3-04 3-05

3-00 3-01 3-02 FBX Box
2-03 2-04 2-05
2-00 2-01 2-02

1-03 1-04 1-05

1-00 1-01 1-02 FBX Box
0-03 0-04 0-05
0-00 0-01 0-02

Fig. 1.1.2.3.5-3 FMD Installation Order to the FMD Chassis

INST01-660
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-670

1.1.2.4 Notes for Installing Flash Drives

The flash-drive that can be controlled with the single DKC model is 192 drives or less. (exclusive
of the spare drive)
However, the flash-drive that can be controlled with one port of the disk adapter (DKA) is 48 drives
or less.
The flash-drive that can be controlled with the twin DKC model is 384 drives or less. (exclusive of
the spare drive)
However, the flash-drive that can be controlled with one port of the DKA is 48 drives or less.

DKC-F810I-CBXB DKC810I-CBXA

HDD SSD SSD SSD SSD SSD SSD SSD SSD HDD

HDD SSD SSD SSD SSD SSD SSD SSD SSD HDD

HDD SSD SSD SSD SSD SSD SSD SSD SSD HDD
DKA2 DKA0

HDD SSD SSD SSD SSD SSD SSD SSD SSD HDD

HDD SSD SSD SSD SSD SSD SSD SSD SSD HDD

DKA2 DKA0
HDD SSD SSD SSD SSD SSD SSD SSD SSD HDD

HDD SSD SSD SSD SSD SSD SSD SSD SSD HDD

HDD SSD SSD SSD SSD SSD SSD SSD SSD HDD

192 SSDs per DKC-F810I-CBXB at a maximum. 192 SSDs per DKC810I-CBXA at a maximum.
(Not includes the spare drive.) (Not includes the spare drive.)

Fig. 1.1.2.4-1 Flash Drive Install Specifications

1.1.2.5 Notes for Installing Flash Module Drive Chassis

Up to two DKC-F810I-FBX (Flash Module Drive Chassis) can be connected to the DKC-0.
Similarly, up to two DKC-F810I-FBX (Flash Module Drive Chassis) can be connected to the
DKC-1.

Table 1.1.2.5-1 Maximum Number of Installable DKC-F810I-FBX and FMD

Maximum number of connectable Maximum number of installable
DKC type
DKC-F810I-FBX FMD (including spare drives)
DKC-0 (CBXA) 2 96
DKC-1 (CBXB) 2 96

INST01-670
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-680

1.1.3 Specifications
(1) Physical Specifications
The DKC810I physical specifications are shown in the following table:

Table 1.1.3-1 DKC810I Physical Specifications

No. Model Number Weight Heat Power Dimension (mm) Air Flow
(kg) Output Consumption Width Depth Height (m3/min.)
(W) (VA)
1 DKC810I-CBXA 141.7 483 *1 508 *1 445 823 436 16.7
2 DKC-F810I-CBXB 140.0 413 *1 435 *1 445 823 436 16.2
3 DKC-F810I-SBX 142.9 640 *1 674 *1 446 536 86 × 9.4
8 unit
4 DKC-F810I-UBX 135.8 640 *1 674 *1 446 536 86 × 6.2
8 unit
5 DKC-F810I-FBX 76.7 600 *1 640 *1 445 720 89 × 8.4
4 unit
6 DKC-F810I-RK42 110.0 — — 600 1,040 2,005 —
7 DKC-F810I-SCOV 33.6 — — — — — —
8 DKC-F810I-SCOVH 33.6 — — — — — —
9 DKC-F810I-DECO 4.4 — — — — — —
10 DKC-F810I-DECOP 4.4 — — — — — —
11 DKC-F810I-KYH 0.5 — — — — — —
12 DKC-F810I-KYP 0.4 — — — — — —
13 DKC-F810I-FDR 12.6 — — 594 45 1,927 —
14 DKC-F810I-FDH42 0.4 — — — — — —
15 DKC-F810I-TR42 1.8 — — — — — —
16 DKC-F810I-BCH 3.7 — — — — — —
17 DKC-F810I-BCP 3.7 — — — — — —
18 DKC-F810I-BUH 5.3 — — — — — —
19 DKC-F810I-BUP 5.3 — — — — — —
20 DKC-F810I-BFH 5.3 — — — — — —
21 DKC-F810I-BFP 5.3 — — — — — —
22 DKC-F810I-FIHT 0.2 — — — — — —
23 DKC-F810I-CRF42 3.6 — — — — — —
24 DKC-F810I-CRF3R 6.3 — — — — — —
25 DKC-F810I-SBBRAL 17.6 — — — — — —
26 DKC-F810I-FMDRAL 5.2 — — — — — —
(To be continued)

INST01-680
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-690

(Continued from the preceding page)

No. Model Number Weight Heat Power Dimension (mm) Air Flow
(kg) Output Consumption Width Depth Height (m3/min.)
(W) (VA)
27 DKC-F810I-PLUC 1.0 — — — — — —
28 DKC-F810I-PHUC 4.5 — — — — — —
29 DKC-F810I-PFUC 2.0 — — — — — —
30 DKC-F810I-PLEC 0.7 — — — — — —
31 DKC-F810I-PHEC 3.1 — — — — — —
32 DKC-F810I-PFEC 1.4 — — — — — —
33 DKC-F810I-PLCC 0.7 — — — — — —
34 DKC-F810I-PHCC 3.0 — — — — — —
35 DKC-F810I-PFCC 1.3 — — — — — —
36 DKC-F810I-SVP 4.0 75 79 — — — 0.54
37 DKC-F810I-HUB 2.3 10 11 — — — —
38 DKC-F810I-MOD5 2.0 1 1 — — — —
39 DKC-F810I-MOD30 3.5 1 1 — — — —
40 DKC-F810I-MOD1J 7.8 1 1 — — — —
41 DKC-F810I-MFC5 0.8 — — — — — —
42 DKC-F810I-MFC30 2.3 — — — — — —
43 DKC-F810I-MFC1J 6.5 — — — — — —
44 DKC-F810I-CC1 1.1 — — — — — —
45 DKC-F810I-CC2 1.7 — — — — — —
46 DKC-F810I-CC4 2.9 — — — — — —
47 DKC-F810I-FC5 — — — — — —
48 DKC-F810I-FC30 — — — — — —
49 DKC-F810I-FC1J — — — — — —
50 DKC-F810I-SCA 1.9 100 105 — — — —
51 DKC-F810I-MP 2.7 170 179 — — — —
52 DKC-F810I-CPEX 2.8 80 84 — — — —
53 DKC-F810I-CM16G 0.022 4 4 — — — —
54 DKC-F810I-CM32G 0.054 7 7 — — — —
55 DKC-F810I-BKMS 1.9 40 *2 42 *2 — — — —
56 DKC-F810I-BKML 0.8 50 *2 53 *2 — — — —
57 DKC-F810I-BMM128 0.08 4 *3 4 *3 — — — —
58 DKC-F810I-BMM256 0.07 4 *3 4 *3 — — — —
59 DKC-F810I-16FC8 2.0 110 116 — — — —
60 DKC-F810I-8FC16 2.4 110 116 — — — —
61 DKC-F810I-16MS8 2.4 120 126 — — — —
62 DKC-F810I-16ML8 2.4 120 126 — — — —
(To be continued)

INST01-690
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-700

(Continued from the preceding page)

No. Model Number Weight Heat Power Dimension (mm) Air Flow
(kg) Output Consumption Width Depth Height (m3/min.)
(W) (VA)
63 DKC-F810I-1PL8 0.02 — — — — — —
64 DKC-F810I-1PS8 0.02 — — — — — —
65 DKC-F810I-1PL16 0.02 — — — — — —
66 DKC-F810I-1PS16 0.02 — — — — — —
67 DKC-F810I-300KCM 0.3 8.6 *4 9.0 *4 — — — —
68 DKC-F810I-600JCM 0.3 8.0 *4 8.5 *4 — — — —
69 DKC-F810I-900JCM 0.3 9.0 *4 9.5 *4 — — — —
70 DKC-F810I-1R2JCM 0.3 — — — —
71 DKC-F810I-3R0H3M 0.83 14.0 *4 14.7 *4 — — — —
72 DKC-F810I-4R0H3M 0.83 — — — —
73 DKC-F810I-400MCM 0.13 2.6 *4 2.8 *4 — — — —
74 DKC-F810I-800MCM 0.13 6.7 *4 7.1 *4 — — — —
75 DKC-F810I-1R6FM 1.4 17.0 *4 18.0 *4 — — — —
76 DKC-F810I-3R2FM 1.4 18.0 *4 19.0 *4 — — — —

*1: Maximum values in case all the fans rotate at maximum.

*2: Maximum values in case the battery charge.
*3: Power is consumed during the battery backup time only.
*4: Actual values at a typical I/O condition. (Random Read and Write, 50 IOPSs for HDD,
2500 IOPSs for SSD/FMD, Data Length: 8Kbytes)
These values may increase for future compatible drives.
NOTE: The maximum power of the drive that DKC810I assumed is as follows.
SFF-Drive: 0.013kW/0.014kVA, LFF-Drive: 0.020kW/0.021kVA,
FMD: 0.034kW/0.036kVA.

INST01-700
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-710

1.1.4 Environmental Specifications

The environmental specifications are shown in the following table.

Item Condition
Operating (*1) Non-operation (*2) Shipping & Storage (*3)
Temperature (ºC) 16 to 32 -10 to 43 -25 to 60
-10 to 35 (*10)
Relative Humidity (%) (*4) 20 to 80 8 to 90 5 to 95
Max. Wet Bulb (ºC) 26 27 29
Temperature Deviation 10 10 20
(ºC/hour)
Vibration (*5) 5 to 10Hz: 0.25mm 5 to 10Hz: 2.5mm Sine Vibration: 4.9m/s2, 5min.
10 to 300Hz: 0.49m/s2 10 to 70Hz: 4.9m/s2 At the resonant frequency with
70 to 99Hz: 0.05mm the highest displacement found
99 to 300Hz: 9.8m/s2 between 3 to 100Hz (*6)
Random Vibration:
0.147m2/s3, 30min, 5 to
100Hz (*7)
Earthquake resistance up to 2.5 (*11) — —
(m/s2)
Shock — 78.4m/s2, 15ms Horizontal:
Incline Impact 1.22m/s (*8)
Vertical:
Rotational Edge 0.15m (*9)
Altitude -60 to 3,000m —

*1: The requirements for operating condition should be satisfied before the storage system is
powered on. Maximum temperature of 32°C should be strictly satisfied at air inlet portion.
The recommended operational room temperature is 21°C to 24°C.
*2: Non-operating condition includes both packing and unpacking conditions unless otherwise
specified.
*3: For shipping and storage, the product should be packed with factory packing.
*4: No condensation in and around the drive should be observed under any conditions.
*5: The vibration specifications apply to all three axes.
*6: See ASTM D999-01 The Methods for Vibration Testing of Shipping Containers.
*7: See ASTM D4728-01 Test Method for Random Vibration Testing of Shipping Containers.
*8: See ASTM D5277-92 Test Method for Performing Programmed Horizontal Impacts Using
an Inclined Impact Tester.
*9: See ASTM D6055-96 Test Methods for Mechanical Handling of Unitized Loads and
Large Shipping Cases and Crates.
*10: When FMDs (DKC-F810I-1R6FM/3R2FM) are installed.
*11: Time is 5 seconds or less in case of the testing with device resonance point (6 to 7Hz).
INST01-710
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-720

1.1.5 Power requirement

Specifications of the power facilities necessary to supply power to the storage system are shown
below.

1. Input Voltage and Input Frequency Requirements

The input voltage and input frequency are as follows.

Table 1.1.5-1 Requirements for Input Voltage and Input Frequency

Frequency Input Voltages (AC) Conditions Tolerance (%)
60Hz ± 2Hz 200V - 240V 1 Phase +6% or -8%
2 Wire + Ground
50Hz ± 3Hz 200V - 240V 1 Phase +6% or -8%
2 Wire + Ground

This unit does not apply to IT power system.

2. Circuit Breaker and Plug

Select a circuit breaker and a plug for the system configuration according to the specification
of following table.

Table 1.1.5-2 Input Power Specifications

Item Input Input Steady Leakage Inrush Current Power Cord
Power Current*1 Current*2 Current Plug Type
1st (0-p) 2nd (0-p) 1st (0-p)
Time
(-25%)
DKC PS 1-phase, 7.18A 3.59A 0.28mA 20A 15A 80ms IEC60320
UBX PS AC200V to 2.07A 1.04A 1.75mA 25A 20A 150ms C14
SBX PS AC240V 2.61A 1.31A 1.75mA 25A 20A 150ms
FBX PS 2.83A 1.42A 0.28mA 20A 10A 80ms

*1: The maximum current in case AC input is not a redundant configuration (in case of 184V
[200V -8%]).
*2: The maximum current in case AC input is a redundant configuration (in case of 184V
[200V -8%]).

3. Choice of PDU
Use the PDU with the circuit breaker.
When using the PDU without a circuit breaker, the current specification of the PDU must be
the same as the circuit breaker rating of PDP.

INST01-720
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-730

1.1.6 Service Clearance and Floor Cutout

Make sure that the service clearance is secured. Never utilize this space for the storage of any
article.
The service clearances and floor cutouts shown in this section are for the DKC-F810I-RK42 Rack.

(1) Single Rack Configuration

(Unit : mm)
Rear
*2
200 d
c

*1 *1
a 610 b
Recommended Rear
dimension : 300
*3
( 250 – 350 )
15
600

576
125

Recommended
75

59
dimension : 200
*3
( 200 – 250 )
839.5

1121
965
2721

1121

Rack-00 Rack (DKC)

(DKC)
81

156.5

580
1000

74 462
35 540
610
5 600 5
Front

Front
c

Floor cutout area for cables

Screw jack
Caster
Service clearance for parts replacement
Rack
(Variable) additional clearance
to endure load
G Grid panel (over 450mm × 450mm)

*1: Clearance (a+b) is based on the floor load rating and the clearance (c).
Floor load rating and required clearances are shown in Table 1.1.6-1.
*2: Clearance (d) is required over 200mm so as to open the rear door.
In case that clearance (d) is less than clearance (b), give priority to clearance (b).
*3: Dimensions in parentheses show allowable range of the floor cutout dimensions. Basically, position the floor
cutout in the center of the rack. However, the position may be off-center as long as the cutout allows smooth
entrance of an external cable (check the relation between the positions of the cutout and the opening on the
bottom plate of the rack) and it is within the allowable range.

Fig. 1.1.6-1 Service Clearance and Floor Cutouts for Single Rack Configuration
INST01-730
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-740

Table 1.1.6-1 Floor Load Rating and Required Clearances for Single Rack
Configuration
Floor Load Required Clearance (a+b) m
Rating Clearance (c) m
(kg/m2) C = -0.3 C=0 C = 0.2 C = 0.4 C = 0.6 C = 0.8 C = 1.0 C = 1.4
Over 700 0 0 0 0 0 0 0 0
600 0.1 0 0 0 0 0 0 0
500 0.3 0.2 0.1 0.1 0 0 0 0
450 0.4 0.3 0.3 0.2 0.1 0.1 0.1 0
400 0.6 0.5 0.4 0.3 0.3 0.2 0.2 0.1
350 0.9 0.7 0.6 0.6 0.5 0.4 0.4 0.3
300 1.4 1.1 1.0 0.9 0.8 0.7 0.6 0.5

NOTE1: Actual clearances for installation should be determined after consulting with
construction specialist responsible for installations in the building, as they could vary
depending on the size/layout of the system and building conditions.
NOTE2: When various configurations of storage systems are arranged in a row, clearance
values based on the largest storage system configuration should be used.
NOTE3: From the viewpoint of maintenance operations, it is suggested that Clearance (c) be
made as large as possible.

INST01-740
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-750

(2) Twin Rack Configuration (Single DKC Model)

(Unit : mm)
Rear *2
200 d

c
*1 *1
a 1210 b

Rear
*3
15 300 15 300 *3

600

576
125
75

125

59

75
200
839.5

1121
839.5

1121
965

2721
965

Rack-00 Rack-01 Rack

(DKC) (DKU) (DKU)
156.5

156.5

81
81

G G

580
1000

74 462 462 74
35 540 540 35
610
5 600 600 5
Front
Front
c

Floor cutout area for cables

Screw jack
Caster
Rack Rack Service clearance for parts replacement
(Variable) additional clearance
to endure load
G Grid panel (over 450mm × 450mm)

*1: Clearance (a+b) is based on the floor load rating and the clearance (c).
Floor load rating and required clearances are shown in Table 1.1.6-2.
*2: Clearance (d) is required over 200mm so as to open the rear door.
In case that clearance (d) is less than clearance (b), give priority to clearance (b).

Fig. 1.1.6-2 Service Clearances and Floor Cutouts for Twin Rack Configuration-1

INST01-750
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-760

Table 1.1.6-2 Floor Load Rating and Required Clearances for Two Rack
Configuration-1
Floor Load Required Clearance (a+b) m
Rating Clearance (c) m
(kg/m2) C = -0.3 C=0 C = 0.2 C = 0.4 C = 0.6 C = 0.8 C = 1.0 C = 1.4
Over 700 0 0 0 0 0 0 0 0
600 0.1 0 0 0 0 0 0 0
500 0.4 0.2 0.1 0 0 0 0 0
450 0.6 0.4 0.3 0.2 0.1 0 0 0
400 1.0 0.7 0.6 0.5 0.4 0.3 0.2 0
350 1.5 1.2 1.0 0.8 0.7 0.6 0.5 0.3
300 2.2 1.8 1.6 1.4 1.3 1.1 1.0 0.8

NOTE1: Actual clearances for installation should be determined after consulting with
construction specialist responsible for installations in the building, as they could vary
depending on the size/layout of the system and building conditions.
NOTE2: When various configurations of storage systems are arranged in a row, clearance
values based on the largest storage system configuration should be used.
NOTE3: From the viewpoint of maintenance operations, it is suggested that Clearance (c) be
made as large as possible.

INST01-760
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-770

(3) Twin Rack Configuration (Twin DKC Model)

(Unit : mm)
Rear *2
200 d

c
*1 *1
a 1210 b

15 300
*4
15 300 *4

600
125
125
75

59

75
200

839.5

1121

2721
965
839.5
965

Rack-10 Rack-00
(DKC) (DKC)
156.5

81
156.5
81

G G 1000

74 462 462 74
35 540 540 35
5 600 600 5

Front
*3
c + 300

Floor cutout area for cables

Screw jack
Caster
Rack Rack
Service clearance for parts replacement
(Variable) additional clearance
to endure load
G Grid panel (over 450mm × 450mm)

*1: Clearance (a+b) is based on the floor load rating and the clearance (c).
Floor load rating and required clearances are shown in Table 1.1.6-3.
*2: Clearance (d) is required over 200mm so as to open the rear door.
In case that clearance (d) is less than clearance (b), give priority to clearance (b).

Fig. 1.1.6-3 Service Clearances and Floor Cutouts for Twin Rack Configuration-2

INST01-770
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-780

Table 1.1.6-3 Floor Load Rating and Required Clearances for Twin Rack
Configuration-2
Floor Load Required Clearance (a+b) m
Rating Clearance (c) m
(kg/m2) C = -0.3 C=0 C = 0.2 C = 0.4 C = 0.6 C = 0.8 C = 1.0 C = 1.4
Over 700 0 0 0 0 0 0 0 0
600 0.2 0 0 0 0 0 0 0
500 0.6 0.4 0.2 0.1 0.1 0 0 0
450 0.8 0.6 0.5 0.4 0.3 0.2 0.1 0
400 1.2 0.9 0.8 0.6 0.5 0.4 0.3 0.2
350 1.8 1.4 1.2 1.1 0.9 0.8 0.7 0.5
300 2.6 2.2 1.9 1.7 1.5 1.4 1.2 1.0

NOTE1: Actual clearances for installation should be determined after consulting with
construction specialist responsible for installations in the building, as they could vary
depending on the size/layout of the system and building conditions.
NOTE2: When various configurations of storage systems are arranged in a row, clearance
values based on the largest storage system configuration should be used.
NOTE3: From the viewpoint of maintenance operations, it is suggested that Clearance (c) be
made as large as possible.

INST01-780
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-790

(4) Three Rack Configuration (Single DKC Model)

(Unit : mm)

c
Rear

*2
200 d

600
*1
a 1810 b
*1

1121

2721
Rack-00 Rack-01 Rack-02
(DKC) (DKU) (DKU)

G G G

1000

5 600 600 600 5

Front
c

Floor cutout area for cables

Screw jack
Rack Rack Rack Caster
Service clearance for parts replacement
(Variable) additional clearance to
endure load
G Grid panel (over 450mm × 450mm)

*1: Clearance (a+b) is based on the floor load rating and the clearance (c).
Floor load rating and required clearances are shown in Table 1.1.6-4.
*2: Clearance (d) is required over 300mm so as to open the rear door.
In case that clearance (d) is less than clearance (b), give priority to clearance (b).

Fig. 1.1.6-4 Service Clearance and Floor Cutouts for Three Rack Configuration-1

INST01-790
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-800

Table 1.1.6-4 Floor Load Rating and Required Clearances for Three Rack
Configuration-1
Floor Load Required Clearance (a+b) m
Rating Clearance (c) m
(kg/m2) C = -0.3 C=0 C = 0.2 C = 0.4 C = 0.6 C = 0.8 C = 1.0 C = 1.4
Over 700 0 0 0 0 0 0 0 0
600 0 0 0 0 0 0 0 0
500 0.5 0.2 0.1 0 0 0 0 0
450 0.9 0.5 0.4 0.2 0.1 0 0 0
400 1.3 1.0 0.8 0.6 0.4 0.3 0.2 0
350 2.0 1.6 1.3 1.1 0.9 0.8 0.6 0.4
300 3.1 2.6 2.2 2.0 1.7 1.5 1.3 1.0

NOTE1: Actual clearances for installation should be determined after consulting with
construction specialist responsible for installations in the building, as they could vary
depending on the size/layout of the system and building conditions.
NOTE2: When various configurations of storage systems are arranged in a row, clearance
values based on the largest storage system configuration should be used.
NOTE3: From the viewpoint of maintenance operations, it is suggested that Clearance (c) be
made as large as possible.

INST01-800
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-810

(5) Three Rack Configuration (Twin DKC Model)

(Unit : mm)

c
Rear

*2
200 d

600
*1
a 1810 b
*1

1121

2721
Rack-10 Rack-00 Rack-01
(DKC) (DKC) (DKU)

G G G

1000

5 600 600 600 5

Front
c

Floor cutout area for cables

Screw jack
Rack Rack Rack Caster
Service clearance for parts replacement
(Variable) additional clearance to
endure load
G Grid panel (over 450mm × 450mm)

*1: Clearance (a+b) is based on the floor load rating and the clearance (c).
Floor load rating and required clearances are shown in Table 1.1.6-5.
*2: Clearance (d) is required over 200mm so as to open the rear door.
In case that clearance (d) is less than clearance (b), give priority to clearance (b).

Fig. 1.1.6-5 Service Clearance and Floor Cutouts for Three Rack Configuration-2

INST01-810
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-820

Table 1.1.6-5 Floor Load Rating and Required Clearances for Three Rack
Configuration-2
Floor Load Required Clearance (a+b) m
Rating Clearance (c) m
(kg/m2) C = -0.3 C=0 C = 0.2 C = 0.4 C = 0.6 C = 0.8 C = 1.0 C = 1.4
Over 700 0 0 0 0 0 0 0 0
600 0.2 0 0 0 0 0 0 0
500 0.7 0.4 0.2 0.1 0 0 0 0
450 1.1 0.7 0.5 0.4 0.2 0.1 0 0
400 1.6 1.2 1.0 0.8 0.6 0.5 0.3 0.1
350 2.3 1.8 1.6 1.3 1.1 1.0 0.8 0.5
300 3.5 2.9 2.5 2.2 2.0 1.8 1.6 1.2

NOTE1: Actual clearances for installation should be determined after consulting with
construction specialist responsible for installations in the building, as they could vary
depending on the size/layout of the system and building conditions.
NOTE2: When various configurations of storage systems are arranged in a row, clearance
values based on the largest storage system configuration should be used.
NOTE3: From the viewpoint of maintenance operations, it is suggested that Clearance (c) be
made as large as possible.

INST01-820
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-830

(6) Four Rack Configuration (When Setting up DKC Racks in the Center)

(Unit : mm)

c
Rear

200 d
*3

600
*1 *1
a 2410 b

1121

2721
Rack-11 Rack-10 Rack-00 Rack-01
(DKU) (DKC) (DKC) (DKU)

G G G G

1000
5 600 600 600 600 5

Front
c

Floor cutout area for cables

Screw jack
Rack Rack Rack Rack
Caster
Service clearance for parts replacement
(Variable) additional clearance
to endure load
G Grid panel (over 450mm × 450mm)

*1: Clearance (a+b) is based on the floor load rating and the clearance (c).
Floor load rating and required clearances are shown in Table 1.1.6-6.
*2: Clearance (d) is required over 300mm so as to open the rear door.
In case that clearance (d) is less than clearance (b), give priority to clearance (b).

Fig. 1.1.6-6 Service Clearance and Floor Cutouts for Four Rack Configuration-1

INST01-830
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-840

Table 1.1.6-6 Floor Load Rating and Required Clearances for Four Rack
Configuration-1
Floor Load Required Clearance (a+b) m
Rating Clearance (c) m
(kg/m2) C = -0.3 C=0 C = 0.2 C = 0.4 C = 0.6 C = 0.8 C = 1.0 C = 1.4
Over 700 0 0 0 0 0 0 0 0
600 0.1 0 0 0 0 0 0 0
500 0.8 0.4 0.2 0 0 0 0 0
450 1.3 0.8 0.6 0.4 0.2 0.1 0 0
400 1.9 1.4 1.1 0.9 0.7 0.5 0.3 0.1
350 2.9 2.3 1.9 1.6 1.4 1.2 0.9 0.6
300 4.4 3.6 3.2 2.8 2.5 2.2 1.9 1.5

NOTE1: Actual clearances for installation should be determined after consulting with
construction specialist responsible for installations in the building, as they could vary
depending on the size/layout of the system and building conditions.
NOTE2: When various configurations of storage systems are arranged in a row, clearance
values based on the largest storage system configuration should be used.
NOTE3: From the viewpoint of maintenance operations, it is suggested that Clearance (c) be
made as large as possible.

INST01-840
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-850

(7) Four Rack Configuration (When Setting up DKC Racks on the Left)

(Unit : mm)

c
Rear

200 d
*2

600
*1 *1
a 2410 b

1121

2721
Rack-10 Rack-00 Rack-01 Rack-02
(DKC) (DKC) (DKU) (DKU)

G G G G

1000
5 600 600 600 600 5

Front
c

Floor cutout area for cables

Screw jack
Rack Rack Rack Rack
Caster
Service clearance for parts replacement
(Variable) additional clearance
to endure load
G Grid panel (over 450mm × 450mm)

*1: Clearance (a+b) is based on the floor load rating and the clearance (c).
Floor load rating and required clearances are shown in Table 1.1.6-7.
*2: Clearance (d) is required over 300mm so as to open the rear door.
In case that clearance (d) is less than clearance (b), give priority to clearance (b).

Fig. 1.1.6-7 Service Clearance and Floor Cutouts for Four Rack Configuration-2

INST01-850
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-860

Table 1.1.6-7 Floor Load Rating and Required Clearances for Four Rack
Configuration-2
Floor Load Required Clearance (a+b) m
Rating Clearance (c) m
(kg/m2) C = -0.3 C=0 C = 0.2 C = 0.4 C = 0.6 C = 0.8 C = 1.0 C = 1.4
Over 700 0 0 0 0 0 0 0 0
600 0.1 0 0 0 0 0 0 0
500 0.8 0.4 0.2 0 0 0 0 0
450 1.3 0.8 0.6 0.4 0.2 0.1 0 0
400 1.9 1.4 1.1 0.9 0.7 0.5 0.3 0.1
350 2.9 2.3 1.9 1.6 1.4 1.2 0.9 0.6
300 4.4 3.6 3.2 2.8 2.5 2.2 1.9 1.5

NOTE1: Actual clearances for installation should be determined after consulting with
construction specialist responsible for installations in the building, as they could vary
depending on the size/layout of the system and building conditions.
NOTE2: When various configurations of storage systems are arranged in a row, clearance
values based on the largest storage system configuration should be used.
NOTE3: From the viewpoint of maintenance operations, it is suggested that Clearance (c) be
made as large as possible.

INST01-860
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-870

(8) Five Rack Configuration

(Unit : mm)

c
Rear

*2
d 200

600
*1 *1
a 3010 b

1121

2721
Rack-11 Rack-10 Rack-00 Rack-01 Rack-02
(DKU) (DKC) (DKC) (DKU) (DKU)

G G G G G

1000
5 600 600 600 600 600 5

Front

Rack Rack Rack Rack Rack

Floor cutout area for cables Service clearance for parts replacement
Screw jack (Variable) additional clearance
Caster to endure load
G Grid panel (over 450mm × 450mm)

*1: Clearance (a+b) is based on the floor load rating and the clearance (c).
Floor load rating and required clearances are shown in Table 1.1.6-8.
*2: Clearance (d) is required over 300mm so as to open the rear door.
In case that clearance (d) is less than clearance (b), give priority to clearance (b).

Fig. 1.1.6-8 Service Clearance and Floor Cutouts for Five Rack Configuration

INST01-870
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-880

Table 1.1.6-8 Floor Load Rating and Required Clearances for Five Rack
Configuration
Floor Load Required Clearance (a+b) m
Rating Clearance (c) m
(kg/m2) C = -0.3 C=0 C = 0.2 C = 0.4 C = 0.6 C = 0.8 C = 1.0 C = 1.4
Over 700 0 0 0 0 0 0 0 0
600 0 0 0 0 0 0 0 0
500 0.8 0.3 0.1 0 0 0 0 0
450 1.4 0.9 0.6 0.3 0.1 0 0 0
400 2.2 1.6 1.2 0.9 0.7 0.5 0.3 0
350 3.3 2.6 2.2 1.8 1.5 1.2 1.0 0.6
300 5.2 4.2 3.7 3.2 2.8 2.5 2.2 1.6

NOTE1: Actual clearances for installation should be determined after consulting with
construction specialist responsible for installations in the building, as they could vary
depending on the size/layout of the system and building conditions.
NOTE2: When various configurations of storage systems are arranged in a row, clearance
values based on the largest storage system configuration should be used.
NOTE3: From the viewpoint of maintenance operations, it is suggested that Clearance (c) be
made as large as possible.

INST01-880
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-890

(9) Six Rack Configuration

(Unit : mm)

c
Rear

*2
d 200
*1

600
a
3610 b
*1

2721
1121
Rack-12 Rack-11 Rack-10 Rack-00 Rack-01 Rack-02
(DKU) (DKU) (DKC) (DKC) (DKU) (DKU)

G G G G G G

1000
5 600 600 600 600 600 600 5

Front

c
Rack Rack Rack Rack Rack Rack

Floor cutout area for cables Service clearance for parts replacement
Screw jack (Variable) additional clearance
Caster to endure load
G Grid panel (over 450mm × 450mm)

*1: Clearance (a+b) is based on the floor load rating and the clearance (c).
Floor load rating and required clearances are shown in Table 1.1.6-9.
*2: Clearance (d) is required over 300mm so as to open the rear door.
In case that clearance (d) is less than clearance (b), give priority to clearance (b).

Fig. 1.1.6-9 Service Clearance and Floor Cutouts for Six Rack Configuration

INST01-890
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-900

Table 1.1.6-9 Floor Load Rating and Required Clearances for Six Rack
Configuration
Floor Load Required Clearance (a+b) m
Rating Clearance (c) m
(kg/m2) C = -0.3 C=0 C = 0.2 C = 0.4 C = 0.6 C = 0.8 C = 1.0 C = 1.4
Over 700 0 0 0 0 0 0 0 0
600 0 0 0 0 0 0 0 0
500 1.0 0.4 0.1 0 0 0 0 0
450 1.7 1.1 0.7 0.4 0.2 0 0 0
400 2.6 1.9 1.5 1.2 0.9 0.6 0.3 0
350 4.0 3.1 2.6 2.2 1.8 1.5 1.2 0.7
300 6.2 5.1 4.4 3.9 3.4 3.0 2.6 2.0

NOTE1: Actual clearances for installation should be determined after consulting with
construction specialist responsible for installations in the building, as they could vary
depending on the size/layout of the system and building conditions.
NOTE2: When various configurations of storage systems are arranged in a row, clearance
values based on the largest storage system configuration should be used.
NOTE3: From the viewpoint of maintenance operations, it is suggested that Clearance (c) be
made as large as possible.

INST01-900
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-910

(10) Seven Rack Configuration

(Unit : mm)

c
Rear

*2
200 d
*1

600
a
4210 b
*1

2721
1121
Rack-12 Rack-11 Rack-10 Rack-00 Rack-01 Rack-02 Rack-03
(DKU) (DKU) (DKU) (DKC) (DKU) (DKU) (DKU)

G G G G G G G

1000
5 600 600 600 600 600 600 600 5

Front

c
Rack Rack Rack Rack Rack Rack Rack

Floor cutout area for cables Service clearance for parts replacement
Screw jack (Variable) additional clearance
Caster to endure load
G Grid panel (over 450mm × 450mm)

*1: Clearance (a+b) is based on the floor load rating and the clearance (c).
Floor load rating and required clearances are shown in Table 1.1.6-10.
*2: Clearance (d) is required over 200mm so as to open the rear door.
In case that clearance (d) is less than clearance (b), give priority to clearance (b).

Fig. 1.1.6-10 Service Clearance and Floor Cutouts for Seven Rack Configuration

INST01-910
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-920

Table 1.1.6-10 Floor Load Rating and Required Clearances for Seven Rack
Configuration
Floor Load Required Clearance (a+b) m
Rating Clearance (c) m
(kg/m2) C = -0.3 C=0 C = 0.2 C = 0.4 C = 0.6 C = 0.8 C = 1.0 C = 1.4
Over 700 0.3 0 0 0 0 0 0 0
600 1.1 0.6 0.3 0.1 0 0 0 0
500 2.1 1.5 1.2 0.9 0.7 0.4 0.2 0
450 2.9 2.2 1.8 1.5 1.2 1.0 0.7 0.4
400 4.0 3.2 2.7 2.3 2.0 1.7 1.4 1.0
350 5.6 4.6 4.0 3.5 3.1 2.7 2.4 1.9
300 8.0 6.7 6.0 5.4 4.9 4.4 4.0 3.3

NOTE1: Actual clearances for installation should be determined after consulting with
construction specialist responsible for installations in the building, as they could vary
depending on the size/layout of the system and building conditions.
NOTE2: When various configurations of storage systems are arranged in a row, clearance
values based on the largest storage system configuration should be used.
NOTE3: From the viewpoint of maintenance operations, it is suggested that Clearance (c) be
made as large as possible.

INST01-920
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-930

1.1.7 Dimensions
(1) DKC Rack

30
(Unit: mm)
TOP VIEW

1,112

1,040
5 600 5

42
FRONT VIEW REAR VIEW

8U

8U

2,006 8U
42U

8U

2U

8U

Fig. 1.1.7-1 Physical Dimensions of the DKC Rack

INST01-930
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-940

(2) DKU Rack

TOP VIEW (Unit: mm)

30
1,112

1,040

600
42

FRONT VIEW

8U

8U

8U
2,006

8U

8U

2U

Fig. 1.1.7-2 Physical Dimensions of the DKU Rack

INST01-940
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-950

(3) Six Rack Configuration

TOP VIEW (Unit: mm)

1,112

3,610

FRONT VIEW

2,006

DKU-Rack DKU-Rack DKC-Rack DKC-Rack DKU-Rack DKU-Rack

Fig. 1.1.7-3 Dimensions of the Six Rack Configuration

INST01-950
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST01-960

1.1.8 Facility grounding check

The storage system must meet all of the following three conditions of installation for
GROUNDING.

a. An insulated grounding conductor that is identical in size and insulation material and thickness
to the grounded and ungrounded branch-circuit supply conductors. It should be green, with or
without yellow stripes, and is to be installed as a part of the branch circuit that supplies the unit
or system.

b. The grounding conductor mentioned in item (a.), should be grounded to earth at the service
equipment or other acceptable building earth ground such as the building frame in the case of a
high rise steel-frame structure.

c. The attachment-plug receptacles in the vicinity of the unit or system are all to be a grounding
type. The grounding conductors serving these receptacles should be connected to earth ground at
the service equipment or other acceptable building earth ground such as the building frame in
the case of a high-rise steel-frame structure.

INST01-960
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-10

2. Installation and De-installation procedure

2.1 New Installation Procedure Table
NOTE: Perform the new installation in numerical order shown in the following table. Proceed
to the next work neglecting unnecessary ones.

When installing Storage system for the first time, perform all hardware installation procedures
before initiating the installation through SVP procedure. Skip the next procedure when the
procedure is not necessary.
If any problems arise during the following procedure, isolate failure part with analysis of SIM log
or SSB log. If neither SIM log nor SSB log has been created, re-check the general procedure and
see TROUBLE SHOOTING SECTION.

Table 2.1-1 New Installation Procedure Table

No. Working Item Model Page
Number
1 Unpacking and Inspection — INST03-02-10
2 Rack and Side Cover Installation  INST03-03-10 through 120
(DKC-F810I-RK42/SCOV/SCOVH)
3 Decoration Panel, Key Kit, Front Door, Front Door  INST03-18-10 through 160
Hinge Kit and PC Tray for RK42 Installation
(DKC-F810I-DECO/DECOP/KYH/KYP/FDR/
FDH42/TR42)
4 Controller Chassis Installation  INST03-04-10 through 230
(DKC810I-CBXA, DKC-F810I-CBXB/CRF42/
CRF3R/BCH/BCP)
5 DKC Power Cord Kit Installation  INST03-06-10 through 80
(DKC-F810I-PLUC/PLEC/PLCC)
6 Drive Chassis Installation  INST03-05-10 through 670
(DKC-F810I-UBX/SBX/FBX/SBBRAL/BUH/BUP/
FMDRAL/BFH/BFP)
7 DKU Power Cord Kit Installation  INST03-06-90 through 260
(DKC-F810I-PHUC/PHEC/PHCC/PFUC/PFEC/
PFCC)
8 Processor Blade, HUB, Cache Memory, Cache  INST03-07-10 through 900
Backup Module kit and Cache Flash Memory, Inter- (Module)
Controller Connecting Kit and Inter-Controller MP/HUB INST03-07A-10 through 150
Connecting Cable Installation
(DKC-F810I-MP/HUB/CM16G/CM32G/CPEX/
BKMS/BKML/BMM128/BMM256/MOD5/MOD30/
MOD1J/MFC5/MFC30/MFC1J)
(To be continued)

INST02-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-20

(Continued from the preceding page)

No. Working Item Model Page
Number
9 Channel Adapter Installation 16FC8/8FC16 INST03-08A-10 through 180
(DKC-F810I-16FC8/8FC16/16MS8/16ML8) (Only Hardware Procedure)
16MS8/16ML8 INST03-08B-10 through 190
(Only Hardware Procedure)
10 Changing of Fibre SFP Transceiver  INST03-09-10 through 70
(DKC-F810I-1PL8/1PS8/1PL16/1PS16)
11 Cache Memory, Cache Backup Module kit, Cache  INST03-10-10 through 920
Flash Memory and Inter-Controller Connecting (Only Hardware Procedure)
Cable
(DKC-F810I-CM16G/CM32G/CPEX/BKMS/BKML/
BMM128/BMM256/MFC5/MFC30/MFC1J)
12 Disk Adapter, Drive and DEV Interface Cable  INST03-11-10 through
Installation 03-11D-460
(DKC-F810I-SCA/CC1/CC2/CC4/300KCM/ (Only Hardware Procedure)
600JCM/900JCM/1R2JCM/3R0H3M/4R0H3M/
400MCM/800MCM/1R6FM/3R2FM)
13 Service Processor Installation  INST03-12-10 through 690
(DKC-F810I-SVP) (Only Hardware Procedure)
14 Filler Panel Installation (DKC-F810I-FIHT)  INST03-13-10 through 30
15 SVP “New Installation” Procedure — INST02-300
16 END — —

INST02-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-30

NOTE: The Maintenance Jumpers of the CE Mode Connectors (CEDT and CEMD).

2 1
M M
A A

Front View of DKC-0

MPB (MPB-1MA/2MA)

Connector
(CEDT)
Maintenance
Jumper
CEDT

CEMD Connector
(CEMD)

INST02-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-40

2.2 Non-Disruptive Installation Procedure Table

NOTE: A serious failure will occur if the works are not done in numerical order shown in the
table.
Perform the non-disruptive addition of the options in numerical order (from No.1 to
No.17) shown in the table below. Neglect a unnecessary work and proceed to the next
work.

Install additional non-disruptive options according to the flow shown below. This work is
completed by installing additional hardware for each option and performing SVP-controlled
installation.
If a fault occurs during or after additional installation, see INST02-110 to locate a faulty unit and
take action. If any other message than the list is displayed, see the SVP MESSAGE SECTION.

Precautions on Non-Disruptive Installation

• “Non-Disruptive” means that the storage system is connected to the host (OS). Non-Disruptive
Installation shall be done with the storage system power ON. However, the storage system may be
disconnected from the host (OS).

Table 2.2-1 Non-Disruptive Installation Procedure Table

No. Working Item Model Page
Number
1 Display the SVP initial screen  SVP01-10 through
2 Confirm the micro-version — OPTVER01-10
3 Rack and Side Cover Installation  INST03-03-10 through 120
(DKC-F810I-RK42/SCOV/SCOVH)
4 Decoration Panel, Key Kit, Front Door, Front Door  INST03-18-10 through 160
Hinge Kit and PC Tray for RK42 Installation
(DKC-F810I-DECO/DECOP/KYH/KYP/FDR/
FDH42/TR42)
5 Controller Chassis Installation  INST03-04-10 through 230
(DKC810I-CBXA, DKC-F810I-CBXB/CRF42/
CRF3R/BCH/BCP)
NOTE When adding DKC-1 in No.5, do not connect the power cord with DKCPS-10, DKCPS-11,
DKCPS-12 and DKCPS-13 in the procedure No.6.
The installation work will fail when the Inter-Controller Connecting kit (DKC-F810I-
MOD5/MOD1J) of No.7 is installed with the power of DKC-1 is on. Consequently, connect the
power cable of the DKCPS following the instructions of installation procedure for No. 7.
6 DKC Power Cord Kit Installation  INST03-06-10 through 80
(DKC-F810I-PLUC/PLEC/PLCC)
(To be continued)

INST02-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-50

(Continued from the preceding page)

No. Working Item Model Page
Number
7 Processor Blade, HUB, Cache Memory, Cache  INST03-07-10 through 900
Backup Module kit and Cache Flash Memory, Inter- (Module)
Controller Connecting Kit and Inter-Controller MP/HUB INST03-07A-10 through 150
Connecting Cable Installation
(DKC-F810I-MP/HUB/CM16G/CM32G/CPEX/
BKMS/BKML/BMM128/BMM256/MOD5/MOD30/
MOD1J/MFC5/MFC30/MFC1J)
8 Cache Memory, Cache Backup Module kit, Cache  INST03-10-10 through 920
Flash Memory and Inter-Controller Connecting
Cable
(DKC-F810I-CM16G/CM32G/CPEX/BKMS/BKML/
BMM128/BMM256/MFC5/MFC30/MFC1J)
9 Installation of SM Size without adding Cache  INST03-17-10 through 50
Memory (*1)
10 Channel Adapter Installation 16FC8/8FC16 INST03-08A-10 through 180
(DKC-F810I-16FC8/8FC16/16MS8/16ML8) 16MS8/16ML8 INST03-08B-10 through 190
11 Changing of Fibre SFP Transceiver  INST03-09-10 through 70
(DKC-F810I-1PL8/1PS8/1PL16/1PS16)
12 Drive Chassis Installation  INST03-05-10 through 670
(DKC-F810I-UBX/SBX/FBX/SBBRAL/BUH/BUP/
FMDRAL/BFH/BFP)
Perform the installation of the Extension Rack,
setting of the SSW switch, and connection of the
power cable.
13 DKU Power Cord Kit Installation  INST03-06-90 through 260
(DKC-F810I-PHUC/PHEC/PHCC/PFUC/PFEC/
PFCC)
14 Turn on the PDU breaker installed in the increased — INST03-14-30
RACK.
NOTE Caution: When performing addition of the data/spare Drive and Device Interface Cable that
accompanies the addition of the DKU, perform the works No. 3, 4, 7, 12, 13, and 14
beforehand.
15 Disk Adapter, Drive and DEV Interface Cable  INST03-11-10 through
Installation 03-11C-1450
(DKC-F810I-SCA/CC1/CC2/CC4/300KCM/
600JCM/900JCM/1R2JCM/3R0H3M/4R0H3M/
400MCM/800MCM/1R6FM/3R2FM)
16 Service Processor Installation (DKC-F810I-SVP)  INST03-12-10 through 690
17 Filler Panel Installation (DKC-F810I-FIHT)  INST03-13-10 through 30
18 END — —

INST02-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-60

*1: The function is only available when CM is in full configuration as follows.

 Module 0 configuration:
1 set of CPEXs and 32 sets of CM16Gs or/and CM32Gs are installed.
 Module 0 & 1 configuration:
2 sets of CPEXs and 64 sets of CM16Gs or/and CM32Gs are installed.

INST02-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-70

2.3 Non-Disruptive De-installation Procedure Table

NOTE: A serious failure occurs if the works are not done in numerical order shown in the
table.
Perform the non-disruptive removal of the options in numerical order (from No.1 to
No.15) shown in the table below. Neglect an unnecessary work and proceed to the
next work.

This work is completed by removing hardware for each option and performing SVP-controlled
removal.
When De-Installation has been all done, make sure that all the removed units are displayed as
“empty” and that the other units are normal. (See the SVP SECTION.)
If a fault occurs during or after removal, see INST02-200 to locate a faulty unit and take action. If
any other message than the list is displayed, see the SVP MESSAGE SECTION.

Precautions on Non-Disruptive De-Installation

• “Non-Disruptive” means that the storage system is connected to the host (OS). Non-Disruptive
De-Installation shall be done with the storage system power ON. However, the storage system
may be disconnected from the host (OS).

Table 2.3-1 Non-Disruptive De-installation Procedure Table

No. Working Item Model Page
Number
1 Display the SVP initial screen  SVP01-10 through
2 Filler Panel De-Installation (DKC-F810I-FIHT)  INST04-10-10 through 30
3 Disk Adapter, Drive and DEV Interface Cable De-  INST04-01-10 through
Installation 04-01C-1320
(DKC-F810I-SCA/CC1/CC2/CC4/300KCM/
600JCM/900JCM/1R2JCM/3R0H3M/4R0H3M/
400MCM/800MCM/1R6FM/3R2FM)
NOTE Proceed to the work No.4 after performing the work No.3.
The system goes down if the power supply of the Drive Chassis to be removed in the work
No.4 is turned off without performing an option removal work, that is, the work No.3.
4 Drive Chassis De-Installation  INST04-02-10 through 360
(DKC-F810I-UBX/SBX/FBX/SBBRAL/BUH/BUP/
FMDRAL/BFH/BFP)
Turn off the power supply of the Drive Chassis.
5 DKU Power Cord Kit De-Installation  INST04-09-90 through 250
(DKC-F810I-PHUC/PHEC/PHCC/PFUC/PFEC/
PFCC)
(To be continued)

INST02-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-80

(Continued from the preceding page)

No. Working Item Model Page
Number
6 Channel Adapter De-Installation 16FC8/8FC16 INST04-04A-10 through 160
(DKC-F810I-16FC8/8FC16/16MS8/16ML8) 16MS8/16ML8 INST04-04B-10 through 160
7 Changing of Fibre SFP Transceiver  INST03-09-10 through 70
(DKC-F810I-1PL/1PS/1PL16/1PS16)
8 Cache Memory, Cache Backup Module kit, Cache  INST04-03-10 through 800
Flash Memory and Inter-Controller Connecting
Cable
(DKC-F810I-CM16G/CM32G/CPEX/BKMS/BKML/
BMM128/BMM256/MFC5/MFC30/MFC1J)
9 De-Installation of SM Size without removing Cache  INST04-11-10 through 60
Memory (*1)
10 Processor Blade, HUB, Cache Memory, Cache  INST04-05-10 through 640
Backup Module kit and Cache Flash Memory, Inter- (Module)
Controller Connecting Kit and Inter-Controller MP/HUB INST04-05A-10 through 150
Connecting Cable De-Installation
(DKC-F810I-MP/HUB/CM16G/CM32G/CPEX/
BKMS/BKML/BMM128/BMM256/MOD5/MOD30/
MOD1J/MFC5/MFC30/MFC1J)
11 Service Processor De-Installation  INST04-08-10 through 210
(DKC-F810I-SVP)
12 DKC Power Cord Kit De-Installation  INST04-09-10 through 80
(DKC-F810I-PLUC/PLEC/PLCC)
13 Controller Chassis De-Installation  INST04-06-10 through 180
(DKC810I-CBXA, DKC-F810I-CBXB/CRF42/
CRF3R/BCH/BCP)
14 Decoration Panel, Key Kit, Front Door, Front Door  INST04-12-10 through 160
Hinge Kit and PC Tray for RK42 De-Installation
(DKC-F810I-DECO/DECOP/KYH/KYP/FDR/
FDH42/TR42)
15 Rack and Side Cover De-Installation — INST04-07-10 through 90
(DKC-F810I-RK42/SCOV/SCOVH)
Turn off the main breaker of the Extension
Rack.
16 END — —

*1: The function is only available when CM is in full configuration as follows.

 Module 0 configuration:
1 set of CPEXs and 32 sets of CM16Gs or/and CM32Gs are installed.
 Module 0 & 1 configuration:
2 sets of CPEXs and 64 sets of CM16Gs or/and CM32Gs are installed.

INST02-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-90

2.4 Disruptive Installation Procedure Table

NOTE: Perform the disruptive de-installation of options in numerical order shown in the
following table. Proceed to the next work neglecting unnecessary ones.

If a fault occurs during or after additional installation, see INST02-110 to locate a faulty unit and
take action. If any other message than the list is displayed, see the SVP MESSAGE SECTION.

Precautions on Disruptive Installation

• “Disruptive” means that the storage system is disconnected from the host (OS). Disruptive
Installation shall be done with the storage system power OFF.

Table 2.4-1 Disruptive Installation Procedure Table

No. Working Item Model Page
Number
1 Display the SVP initial screen  SVP01-10 through
2 Confirm the micro-version  OPTVER01-10
3 POWER OFF of Storage system  INST03-14-50 through 60
4 POWER ON of Storage system  INST03-14-10 through 20
5 END  

INST02-90
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-100

2.5 Disruptive De-installation Procedure Table

NOTE: Perform the disruptive de-installation of options in numerical order shown in the
following table. Proceed to the next work neglecting unnecessary ones.
Remove additional disruptive options according to the flow shown below.

When De-Installation has been all done, make sure that all the removed units are displayed as
“empty” and that the other units are normal. (See the SVP SECTION.)
If a fault occurs during or after removal, see INST02-200 to locate a faulty unit and take action. If
any other message than the list is displayed, see the SVP MESSAGE SECTION.

Precautions on Disruptive De-Installation

• “Disruptive” means that the storage system is disconnected from the host (OS). Disruptive De-
installation shall be done with the storage system power OFF.

Table 2.5-1 Disruptive De-installation Procedure Table

No. Working Item Model Page
Number
1 Display the SVP initial screen  SVP01-10 through
2 POWER OFF of Storage system  INST03-14-50 through 60
3 POWER ON of Storage system  INST03-14-10 through 20
4 END  

INST02-100
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-110

2.6 Trouble shooting for errors in install SVP procedure

2.6.1 ECC group + LDEV

START

Yes
Is ONL3349E displayed?
No
Refer to TRBL02-250 No Is any LDEV installed?

No Configuration match Yes

with what you want?
(*2)
Yes Is there any LDEV No
status abnormal? (*1)
No
Is Installation completed? Yes
(*3)
See SVP SECTION
Perform installation (*4) Yes for LDEV formatting.
with the same configuration.
Is there any PDEV No
status abnormal? (*1)
Is Auto Assignment Yes
Yes expectation? (*5)

See REPLACE SECTION No

for replacing failure PDEV.
See “Provisioning Guide
for Open Systems”
for setting Auto Assignment.

See MICRO-FC SECTION (*6)

for Configuration backup.

END

INST02-110
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-120

*1: Select (CL) [Maintenance] in the ‘SVP’ window.

*2: Select (CL) [Install]-[Refer Configuration] in the ‘SVP’ window.
*3: Wasn’t INS2450E displayed when select (CL) [Install]-[Change Configuration] in the
‘SVP’ window?
*4: There may be a case that you cannot change the type of spare drive.
In that case, install again with the same configuration except for the spare drive.
After completing the installation, uninstall the spare drive and install the spare drive again.
*5: Select (CL) [Components] in the ‘Storage Navigator’ window.
*6: Select (CL) [Install]-[Copy Config Files]-[Create Configuration Backup] in the ‘SVP’
window.

INST02-120
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-130

2.6.2 DKA

START

Is there any DKA No

status abnormal?
(*1)

Yes
See REPLACE SECTION
for replacing failure DKA.

Configuration match Yes

with what you want?
(*2)
No
Perform installation (*3)
with the same configuration.

See MICRO-FC SECTION (*4)

for Configuration backup.

END

*1: Select (CL) [Maintenance] in the ‘SVP’ window.

*2: Select (CL) [Install]-[Refer Configuration] in the ‘SVP’ window.
*3: The installation of the cluster 1 may be completed depending on the contents of the
installation failure. In this case, if the installation is performed again, processing will
begin from the cluster 2.
*4: Select (CL) [Install]-[Copy Config Files]-[Create Configuration Backup] in the ‘SVP’
window.

INST02-130
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-140

2.6.3 Number of Channel

START

Configuration match with Yes

what you want? (*2)

No
Perform installation
with the same configuration.

Is there any CHA status No

abnormal? (*1)
Yes
See REPLACE SECTION
for replacing failure PDEV.

See MICRO-FC SECTION (*3)

for Configuration backup.

END

*1: Select (CL) [Maintenance] in the ‘SVP’ window.

*2: Select (CL) [Install]-[Refer Configuration] in the ‘SVP’ window.
*3: Select (CL) [Install]-[Copy Config Files]-[Create Configuration Backup] in the ‘SVP’
window.

INST02-140
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-150

2.6.4 Cache Capacity

START

Cache PCB installation Yes

failed as [ONL4465E]
was displayed?
See INSTALLATION SECTION
No for removal of the Cache PCB.

Is there any No
CACHE and BKM status
abnormal? (*1)
Yes
In the case of 2 module configuration,
check MFC cables are connected
correctly. (Refer to LOC05-130)

See REPLACE SECTION (*6)

for replacing failure CACHE.

Is there any No
CACHE status abnormal?
(*1) Cache capacity and
Yes
Yes SM capacity match with
what you want? (*2)
In the case of 2 module configuration,
check MFC cables are connected
correctly. (Refer to LOC05-130) No
Perform installation (*3)
See REPLACE SECTION (*7) with the same configuration.
for replacing failure CACHE.

Is it installing No
Is there any No CACHE to new CLPR?
BKM status abnormal? (*2)
(*1) Yes
Yes Allocate the extended Using CACHE (*4)
See REPLACE SECTION size of CLPR0 to Target CLPR.
for replacing failure BKM.
See MICRO-FC SECTION (*5)
for Configuration backup.

END

INST02-150
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-160

*1: Select (CL) [Maintenance] in the ‘SVP’ window.

*2: Select (CL) [Install]-[Refer Configuration] in the ‘SVP’ window.
*3: The installation of the cluster 1 may be completed depending on the contents of the
installation failure. In this case, if the installation is performed again, processing will
begin from the cluster 2.
*4: Select (CL) [Settings]-[Environmental Setting]-[Partition Definition...] in the ‘Storage
Navigator’ window. Extend Cache memory reference to “Performance Guide” - “Creating
a CLPR”.
*5: Select (CL) [Install]-[Copy Config Files]-[Create Configuration Backup] in the ‘SVP’
window.
*6: When diagnosis error of BKM occurs, see DIAGNOSIS SECTION “5.1.3 INLINE CUDG
Trouble shooting”.
*7: When work stops it by SVP reboot, please perform self-replacement of CACHE-
1CA/2CA.

INST02-160
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-170

2.6.5 MPB + Module

START

Configuration match with No

what you want? (*1) Perform installation
with the same configuration.
Yes

Module installation
failed as [ONL4357E] or Yes
[ONL4465E] was
displayed? See INSTALLATION SECTION
for removal of the Module.
No

Is there any Yes

MPB status abnormal?
(*2) See REPLACE SECTION
No for replacing failure MPB.

Is there any Yes

Path status abnormal?
(*3) See REPLACE SECTION
for replacing failure CACHE.
No

Is there any Yes

Path status abnormal?
(*3)
No Check the SIM and replace
the displayed PCB.
Is there any
SSVPMN status Yes
abnormal? (*2) See REPLACE SECTION
for replacing failure SSVPMN.
No

Is Auto Assignment Yes

expectation?
(*4)
No
See “Provisioning Guide
for Open Systems”
for setting Auto Assignment.

See MICRO-FC SECTION (*5)

for Configuration backup.

END

INST02-170
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-180

*1: Select (CL) [Install]-[Refer Configuration] in the ‘SVP’ window.

*2: Select (CL) [Maintenance] in the ‘SVP’ window.
*3: Select (CL) [Maintenance]-[Inter-PCB Logical Path Status] in the ‘SVP’ window.
*4: Select (CL) [Components] in the ‘Storage Navigator’ window.
*5: Select (CL) [Install]-[Copy Config Files]-[Create Configuration Backup] in the ‘SVP’
window.

INST02-180
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-190

2.6.6 SVP

START

Configuration match with Yes

what you want? (*1)

No

Perform installation
with the same configuration.

Yes
Is an IP Address right?
(*1)
No

See SVP SECTION

for Set IP Address.

See MICRO-FC SECTION (*2)

for Configuration backup.

END

*1: Select (CL) [Install]-[Set IP Address] in the ‘SVP’ window.

*2: Select (CL) [Install]-[Copy Config Files]-[Create Configuration Backup] in the ‘SVP’
window.

INST02-190
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-200

2.7 Trouble shooting for errors in remove SVP procedure

2.7.1 ECC group + LDEV

START

Configuration match with No

what you want? (*1)

Yes

No
Is removal completed?
(*2)
Perform removal
Yes with the same configuration.

Was SSW replace No

directions screen is displayed
into remove?

Yes
See REPLACE SECTION
for replacing object SSW.

See MICRO-FC SECTION (*3)

for Configuration backup.

END

*1: Select (CL) [Install]-[Refer Configuration] in the ‘SVP’ window.

*2: Wasn’t INS2450E displayed when select (CL) [Install]-[Change Configuration] in the
‘SVP’ window?
*3: Select (CL) [Install]-[Copy Config Files]-[Create Configuration Backup] in the ‘SVP’
window.

INST02-200
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-210

2.7.2 DKA

START

Is there any DKA No

status abnormal? (*1)
Yes
See REPLACE SECTION
for replacing failure DKA.

Configuration match Yes

with what you want? (*2)
No
See MICRO-FC SECTION (*4)
Perform removal (*3) for Configuration backup.
with the same configuration.

END

*1: Select (CL) [Maintenance] in the ‘SVP’ window.

*2: Select (CL) [Install]-[Refer Configuration] in the ‘SVP’ window.
*3: The removal of the cluster 1 may be completed depending on the contents of the de-
installation failure. In this case, if the de-installation is performed again, processing will
begin from the cluster 2.
*4: Select (CL) [Install]-[Copy Config Files]-[Create Configuration Backup] in the ‘SVP’
window.

INST02-210
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-220

2.7.3 Number of Channel

START

Configuration match with Yes

what you want? (*1)
No See MICRO-FC SECTION (*2)
for Configuration backup.
Perform removal
with the same configuration.

END

*1: Select (CL) [Install]-[Refer Configuration] in the ‘SVP’ window.

*2: Select (CL) [Install]-[Copy Config Files]-[Create Configuration Backup] in the ‘SVP’
window.

INST02-220
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-230

2.7.4 Cache Capacity

START

Is Option
installed only on cluster 2 Yes
sides in two module
(*7)
configuration?
If MPB is blocked, recover it by
No replacement, and then perform removal
again in the same configuration.
Is there any
No
CACHE and BKM status
abnormal? (*1)
Yes
In the case of 2 module
configuration, check MFC cables
are connected correctly. Is there any BKM No
(Refer to LOC05-130) status abnormal? (*1)
See REPLACE SECTION (*6) Yes
for replacing failure CACHE.
See REPLACE SECTION
for replacing failure BKM.

Is there any CACHE No

status abnormal? (*1)
Configuration match Yes
Yes
with what you want? (*2)
In the case of 2 module
configuration, check MFC cables No
are connected correctly.
Perform removal See MICRO-FC SECTION
(Refer to LOC05-130)
with the same configuration. for Configuration backup.
See REPLACE SECTION (*5) (*3) (*4)
for replacing failure CACHE.

END

*1: Select (CL) [Maintenance] in the ‘SVP’ window.

*2: Select (CL) [Install]-[Refer Configuration] in the ‘SVP’ window.
*3: The removal of the cluster 1 may be completed depending on the contents of the de-
installation failure. In this case, if the de-installation is performed again, processing will
begin from the cluster 2.
*4: Select (CL) [Install]-[Copy Config Files]-[Create Configuration Backup] in the ‘SVP’
window.
*5: When the procedure is interrupted by a SVP reboot, perform self-replacement for both
1CA and 2CA.
*6: When diagnosis error of BKM occurs, see DIAGNOSIS SECTION “5.1.3 INLINE CUDG
Trouble shooting”.
*7: CACHE-2CB/2CD are installed, but CACHE-1CB/1CD are not.

INST02-230
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-240

2.7.5 MPB + Module

START

Configuration match with Yes

what you want? (*1)
In case of Module de-installation,
No remove MODCON cable.
(Refer to page INST04-05-360)

In case of Module de-installation,

remove CM and BKM.
(Refer to page
INST04-05-110, INST04-05-260)

Remove MPB and HUB Kit.

(Refer to page
INST04-05-390, INST04-05-430)

In case of Module de-installation,

Remove Inter-Controller
Connecting Kit.
(Refer to page INST04-05-470)

Perform removal See MICRO-FC SECTION (*2)

with the same configuration. for Configuration backup.

END

*1: Select (CL) [Install]-[Refer Configuration] in the ‘SVP’ window.

*2: Select (CL) [Install]-[Copy Config Files]-[Create Configuration Backup] in the ‘SVP’
window.

INST02-240
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-250

2.7.6 SVP

START

Configuration match with Yes

what you want? (*1)

No See MICRO-FC SECTION (*2)

Perform removal for Configuration backup.
with the same configuration.

END

*1: Select (CL) [Install]-[Set IP Address] in the ‘SVP’ window.

*2: Select (CL) [Install]-[Copy Config Files]-[Create Configuration Backup] in the ‘SVP’
window.

INST02-250
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-260

2.8 Availability of Installation and De-installation

The pair can be suspended if the ESTPAIR or paircreate (pairesync) command is issued during the
HDD Canister or the Cache PCB installation/de-installation. Please ask your customer before the
online maintenance operation.

HDD Canister Cache

CHA DKA MP
DATA SPARE PCB
P.P. Status Installation/ Installation/ Installation/ Installation/
De- De-
Installation De- De- Installation De- De-
installation installation
installation installation installation installation
TC- TC-MF MCU   (*1)    SVP4280W  
MF/ path
TC established RCU        
(*5) SVP2031W
During MCU   SVP2059W  (*2) SVP4280W  
(*1)
initial copy
RCU  SVP2034W  SVP2079W  (*2) SVP2038W  
After SVP2031W
MCU     (*2) SVP4280W  
completing (*1)
initial copy RCU  SVP2034W    (*2) SVP2038W  
SVP2031W
MCU     (*2) SVP4280W  
Suspend (*1)
RCU  SVP2034W    (*2) SVP2038W  
UR TC-MF MCU
(JNL- path        
GROUP)
established RCU
MCU
Initial  SVP3825W      
RCU
MCU
Active  SVP3825W      
RCU
MCU
Halting  SVP3825W      
RCU
MCU
Stop  SVP3825W      
RCU
MCU
Stopping  SVP3825W      
RCU
(To be continued)

INST02-260
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-270

(Continued from the preceding page)

HDD Canister Cache
CHA DKA MP
DATA SPARE PCB

De-installation

De-installation

De-installation

De-installation

De-installation
De-installation

Installation/

Installation/

Installation/

Installation/
Installation

Installation
P.P. Status

SI- Pending/ S-VOL

MF Resync/  SVP2485W     (*7)  
SP-Pend T-VOL
S-VOL
Duplex  SVP2485W     (*7)  
T-VOL
S-VOL
Split  SVP2485W     (*7)  
T-VOL
S-VOL
Suspend  SVP2485W     (*7)  
T-VOL
FCv2 S-VOL
During copy  SVP2485W     
T-VOL
S-VOL
NOCOPY  SVP2485W     
T-VOL
Incremental S-VOL
 SVP2485W     
FlashCopy T-VOL
XRC During initial Primary  (*3)  (*4)   (*4)
copy Secondary  (*3)     
Primary  (*3)  (*4)   (*4)
Established
Secondary  (*3)     
Primary  (*3)  (*4)   (*4)
Suspend
Secondary  (*3)     
(To be continued)

INST02-270
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-280

(Continued from the preceding page)

HDD Canister Cache
CHF CHM DKA MP
DATA SPARE PCB

De-installation

De-installation

De-installation

De-installation

De-installation

De-installation
De-installation

Installation/

Installation/

Installation/

Installation/
Installation

Installation

Installation
P.P. Status

UR TC-MF MCU          
(DATA- path
VOL)
established RCU      SVP4280W    
MCU  SVP2031W  SVP2059W  SVP3848W    
During
SVP4291W
initial copy RCU  SVP2034W  SVP2079W  SVP4280W   
(*6)
After MCU  SVP2031W    SVP3848W    
completing SVP4291W
initial copy RCU  SVP2034W    SVP4280W   
(*6)
MCU  SVP2031W    SVP3848W    
Suspend
RCU  SVP2034W    SVP4280W    
MCU  SVP2031W    SVP3848W    
Suspending SVP4291W
RCU  SVP2034W    SVP4280W   
(*6)
MCU  SVP2031W    SVP3848W    
Deleting SVP4291W
RCU  SVP2034W    SVP4280W   
(*6)

 : Maintenance is available.
SVPXXXXW : Maintenance is not available based on the specification. Refer to SVP
MESSAGE SECTION.
*1: If CU which all HDEV’s are deleted from by this operation exists and there is registration
of RCU in this CU, SVP will display a warning message with SVP2466W.
*2: When the different ‘DKC – Emulation – Type’ of CHA is installed, SVP displays a
warning message with SVP3289W.
*3: When a maintenance operation is needed while XRC is being used, XRC should be
stopped before the maintenance operation.

INST02-280
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-290

*4: When a maintenance operation is needed while XRC is being used, I/O’s for XRC pair
volumes or XRC itself should be stopped before the maintenance operation.
If the maintenance operation must be done while XRC is being used, you must confirm
that the usage of Sidefile monitor is less than 20% of total Cache capacity by monitoring
each combination of MPPK and CLPR usage before you start the maintenance operation.
Only when the usage of Sidefile monitor is less than 20% of total Cache capacity, you can
proceed the maintenance operation.
Refer to SVP SECTION “2.4 Monitoring” (SVP02-04-10) about Sidefile monitor.
Select the [Monitor] icon in the ‘SVP’ window.
Next select the [Monitor] menu in the ‘Information’ window and select [start...].
Next select the ‘Sidefile’ box in the ‘Item’ menu in the ‘Monitoring’ window and select
[OK].
*5: It is impossible to change the DKC No, SSID, or DKC Emulation type by system tuning
when TrueCopy for Mainframe or TrueCopy is used.
*6: In this operation, when all of CHM were set down, the warning message of ‘SVP4291W’
will be outputted.
*7: In the case of SI-MF, when all CHM is specified to de-install with pair includes 3390-A
volume, the alert message of ‘SVP4313W’ is shown.

INST02-290
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-300

2.9 New Installation procedures without the pre-installation at a customer site

2.9.1 Application
These procedures are applied to a new installation without the pre-installation at a customer site or
the pre-installation at the warehouse as shown below.

• Installing the micro programs into the storage system. Its version must be appropriate one.
• Installing the configuration information which is appropriate to the customer.

If these procedures are used in other cases, their processes are not assured.

INST02-300
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-310

2.9.2 Conditions to use these procedures

These procedures can be used in the following conditions:

 The installation of the Hardware parts (for example, the connections of cables, power supplies
and so on) have been finished. (For the Hardware installation, refer to “2.1 New Installation
Procedure Table” (INST02-10 ~ INST02-20))

 The PC (SVP) is installed and can be used. (For the SVP installation, refer to REP03-21-210 ~
REP03-21-670)

INST02-310
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-320

2.9.3 Procedures
(1) Summary
The procedures are divided roughly into 3 processes.
 Pre-processing (the installation of the micro-programs into the SVP HD : (1)-(8) in the
following flow)
 Execution of “Define Configuration and Install” by the SVP.(By this procedure, the
customer’s configurations are defined, and the micro-programs are installed.) : ((9)-(12) in
the following flow)
 Others ((13)-(33) in the following flow)

(2) Processing Flow

The processing flow of the new installation is as follow:

INST02-320
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-330

START

(1)-0 Backup the current Config in the Config media of the same value.
(1)-1 Check the size of the Cache, CM DIMM, CU number and IP address with the DKC and remember them for
later use in step (12)-1, (12)-2.
(1)-2 Turn off the “POWER ON/OFF” switch on the DKCPANEL.
(1)-3 Make sure the breaker is off (DKU and DKC). (If it is “on”, turn off the breaker after the SVP is shut down.)
[Breaker: INST03-14-80, SVP Shut Down: SVP01-170]
(1)-4 If the PUBLIC (SNMP Web Console) or INTERNAL (ASSIST) cables in the SVP are connected, disconnect
them. Do not disconnect other cables. [LOC04-40]

(2) Turn on the breaker (DKU and DKC) and wait for the SVP ready to use.
(Don’t turn on the “POWER ON/OFF” switch on the DKCPANEL.)
[Power ON Procedure of Storage system: INST03-14-10]

(3) Set the SVP PS ON/OFF INH switch (SVP RAS SW #1) on the SVP to ON (lower position).
When the Additional SVP is installed, set the SVP PS ON/OFF INH switch (SVP RAS SW #1) on the SVP-
OPTION to ON (lower position).
[LOC03-120]

(SVP procedure)
(4) Set TOD
(At this time, “Communication Error” may occur. You can ignore the error.)
[INST05-02-10 ~ INST05-02-30]

INST02-330
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-340

(SVP procedure)
(5) Execute the following procedures: (*9)
[Install micro-programs and configuration to the HD to the SVP]
[REP03-21-240 ~ REP03-21-510]
step0: Connect to the SVP display from the Maintenance PC by the remote desktop.

step1: Prepare the 1st and 2nd CD-ROM. (*1)

step2: Uninstall any additional software installed on the SVP such as Hi-Track/C-Track and Anti-Virus
client.

step3: Click “START” on the task bar and select “Control Panel”-“Programs and Features”.
Uninstall Apache, Tomcat, JRE:Java(TM) + Java(TM) SE Development Kit, Perl and Flash. Do not
reboot after each uninstall. Stop any services that are coming out in the Warning messages.
REP03-21-250 1. Apache (launch the uninstallation batch)
Select “Start”-“All Programs”-“Accessories”-
“Command Prompt (right click to administrator)”
and enter the following command:
\\tsclient\e\JavaAp\Apache\ApacheUnInst.bat (enter)
Remove CD-ROM from Maintenance PC’s drive.

REP03-21-260 2. Apache Tomcat uninstall from “Control Panel”-“Programs and Features”.

During uninstall the following message is displayed:
“Remove all files in your Tomcat directory?
If you have anything you created you want to keep, click No.”
Select Yes.
Do NOT allow Reboot!

REP03-21-290 3. Java SE Development Kit uninstall from “Control Panel”-

“Programs and Features”.
Do NOT allow Reboot!

4. Java Update uninstall from “Control Panel”-“Programs and Features”.

Do NOT allow Reboot!

REP03-21-340 5. Perl uninstall from “Control Panel”-“Programs and Features”.

Do NOT allow Reboot!

REP03-21-360 6. Flash uninstall from “Control Panel”-“Programs and Features”.

Do NOT allow Reboot!

step4: Insert the 1st CD-ROM disk into the Maintenance PC’s drive.

INST02-340
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-350

step5: Enter the following command: \\tsclient\E\setup.exe (enter).

* In the case Maintenance PC’s CD-ROM drive is “E:”.

Message is displayed:
“(SUP4186W) Initializing the SVP that is currently operating. Do you want to continue?”
Select Yes.
The following message is displayed:
“The SVP is running. The PC will be rebooted to stop the SVP. Please retry the setup after the PC
reboots.”
Select Finish after check Yes in radio buttons.
SVP reboots....
After reboot 2 icons are displayed (RAID ADMIN and OTHER USER) Switch to OTHER USER
icon and enter “Administrator” (user) and “r41d-administrate-admin” (password). Follow the
process on the
screen.

Select [CD-R] to install configuration information from CD-R, when the message CNF4061i.
Enter the key code of the configuration information when the message CNF4055i, and then click
[OK]. (*11)
Insert the second CD-R (OSS), when requested and select [OK].

Java, Perl, Apache Tomcat and Flash is being installed at this step.
Do not change any parameters during install (leave unchanged values).

step6: Remove the CD-ROM from the Maintenance PC’s drive.

This operation causes the “SVP Reboot”. Then wait few minutes and reconnect by the remote desktop.

(SVP procedure)
(6) Set IP Address
IP Address must be 126.255.254.15 and Subnet mask must be 255.0.0.0. Also, “Target” must be “SVP”.
(Don’t select “SVP and DKC” as the “Target”. [INST05-02-40 ~ INST05-02-70] (*2)
Besides, do not select “Use Duplex SVP” in the “External IP Address” box.
Config BackUp is accompanies.

INST02-350
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-360

(SVP procedure)
(7) Delete LOGs.
[Log Delete: SVP02-03-10 ~ SVP02-03-20, SIM Log Complete: SVP02-08-10 ~ SVP02-08-20] (*3)

(8) Set the SVP PS ON/OFF INH switch on the SVP to OFF (upper position).
When the Additional SVP is installed, set the SVP PS ON/OFF INH switch on the SVP-OPTION to OFF
(upper position).

(9) Set all packages to be installed.

Set the packages (CHA, DKA, MPB and so on) to be installed to their locations of CL1 and CL2. The same
kind of package must be set to the same location of each CL (CL1 and CL2).
[LOC02-90 ~ LOC02-120] (*3-1)

(10) Set the Maintenance Jumpers to CE Mode connectors (CEMD) and (CEDT) on the only MPB-1MA and
MPB-2MA. (*4) For two Modules, insert Jumpers in the MPB-1MC and MPB-2MC of Module 1 too.
NOTE: Don’t pull out these Jumpers until (14). [INST02-30]

(11) Turn on the “POWER ON/OFF” switch on the DKCPANEL. [INST03-14-20]

INST02-360
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-370

Change the SVP mode to “Initial Setting”. (*5)

(SVP procedure) -- (Execution of Define Configuration and Install)
(12)-1 Execution of Config Exchange Procedure.
Select the “Install” in the “SVP” window and select “Copy Config Files” in the “Install” window. And select
“All Configuration Files” in the “Copy Config Files” window.
[MICRO07-60 ~ MICRO07-70]
(12)-2 Define the configuration information that you want to install now for this storage system.
Then, the defined size of the Cache and CM DIMM must be equal to ones of the Cache and CM DIMM
equipped for the storage system. (*6) (*10)
The configuration information must be defined according to the SVP guidance. Especially, you must not
forget the definition of the following information.
 DKC Serial No., IP Address.  Host Interface Configuration:
 Cache Configuration  PDEVs, LDEVs, etc. [INST05-02-80 ~ INST05-02-470]

(13) Turn off the “POWER ON/OFF” switch on the DKCPANEL. [INST03-14-50 ~ INST03-14-60]

(14) Pull out the Maintenance Jumpers from all the MP PCBs. (*4)

(15) Set the Volatile Jumpers on all the CM PCBs.

NOTE: Don’t pull out these Jumpers until (27).

INST02-370
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-380

(16) Delete error logs.

[Log Delete: SVP02-03-10 ~ SVP02-03-20, SIM Log Complete: SVP02-08-10 ~ SVP02-08-20] (*3)

(17) Connect the LAN cables disconnected at (1)-4, if it is necessary.

(18) Turn on the “POWER ON/OFF” switch on the DKCPANEL. [INST03-14-20]

(19) Wait till the READY LED is lit and Power Event Log (SYSTEM ON) is reported
from all installed MPs.

(20) STORAGE SYSTEM Yes (21) Perform operations according to

ALARM LED lit? SIM/SSB indications.

No

(22) Power (23)

Event Log reported from No No
Wait for 20 minutes.
all installed MPs?

Yes Yes (24) Perform operations according to

SIM/SSB indications.

(25) Make sure that the status shows the configuration which was defined in (12)-1, (12)-2. (*7)
[SVP03-01-10]

(26) Turn off the “POWER ON/OFF” switch on the DKCPANEL. [INST03-14-50]

(27) Pull out the Volatile Jumpers from all the CM PCBs.

(28) Turn on the “POWER ON/OFF” switch on the DKCPANEL. [INST03-14-50 ~ INST03-14-60]

(SVP procedure)
(29) Execute DKU Path inline test (A0/A3 routine test) [INST05-02-500 step 2]
[DKU PATH INLINE Test Procedure: DIAG04-130]
(30) Check storage system status and micro-versions of each MP.
[INST05-02-500 step 3 (Activating and Terminating STATUS: [SVP03-01-10])]
(31) Format LDEV [INST05-02-510]
(32) Execute the “On-line Micro-program Exchange” for the SSVP, CMBK, BTCL, Expander, Expander(FMU)
and CFM. [MICRO04-10]
(33) Check storage system status.
[INST05-02-530 step 5 (Activating and Terminating STATUS: [SVP03-01-10])]

INST02-380
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-390

(34) Execute the “Online Micro program Exchange” for the HDD.
[MICRO04-10]

(35)
Is the SVP High Yes
Reliability Kit
installed?
(36)-1 Execute the SVP Operation. [INST03-12-30 ~ 140]
No [INST03-12-150 ~ 530]
NOTE: However, the IP address used for access is not 126.255.254.15.
Please use IP address of the Additional SVP.
(36)-2 Execute the SVP Operation. [INST03-12-540 ~ 590]
(36)-3 Execute the SSVP Reset. [INST03-12-600]
(36)-4 Execute the SVP Operation. [INST03-12-610 ~ 690]

(SVP procedure)
(37) Delete error logs.
[Log delete: SVP02-03-10 ~ SVP02-03-20, SIM Log Complete: SVP02-08-10 ~ SVP02-08-20] (*3)

END

INST02-390
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-400

*1 : The 1st CD-ROM includes the micro-programs and configuration information and Storage
Navigator to be installed into the storage system.
The 2nd CD-ROM (OSS) includes Apache, Perl, Java and Tomcat.
*2 : Even if the “IP Address” is “126.255.254.15” and the “Subnet Mask” is “255.0.0.0” on the
screen of “Set IP Address”, be sure to select “OK” and reply “OK” to the message “This
will reboot SVP.”.
*3 : It’s necessary to execute the procedure of “SIM Log Complete” before deleting the SIM
data.
*3-1: At least, a pair of MP PCBs must be installed in the CL1 and CL2 PCB locations.
*4 : Refer to the following about the Maintenance Jumpers.
• INST02-30 “NOTE”
*5: Press the following keys at the same time to change the mode to “Initial Setting”.
[SHIFT], [CTRL], [I]
And input the password. (*8)
*6: In this definition, specify the actual DKC Serial Number.
Also, “IP Address” should be specified as follows:
 Specifying the IP Address according to the DKC Serial Number Select “Based on
Serial Number”, and the IP Address will be assigned automatically.
 Specifying in option
Select “Specified” and specify the optional address for the IP Address.
And, the defined value for the size of the Cache and CM DIMM should be equal to the
value that was confirmed at (1) in the processing flow. After the configuration
information is defined, Turn on the “POWER ON/OFF” switch of the DKCPANEL
and the reboot of the SVP will be executed.
*7: Surely, check the following status:
(1) the condition of each PCB status.----- PCB Kind/Normal or not/etc
(2) the micro-program version
*8: For the password, ask the technical support division. And use it with their approval.

INST02-400
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-410

*9: The SIM = BF85A3 (Basic SVP: SVP RAS Switch#1 remains (SVP PS ON/OFF INH
SW)) may be reported. When the SVP high-reliability kit is installed, the SIM = BF86A3
(Optional SVP: SVP RAS Switch#1 remains (SVP PS ON/OFF INH SW)), BFE3A2
(SVP duplication setting defect) and 7FF201 (standby SVP failure detection) may occur
but there is no problem because they occur in process of the SVP replacement.
*10: Select (CL) the [All Microprograms] and select (CL) the [OK] button. (INST05-02-440)

*11: The Following tables show all the configuration key codes.

Type Configuration key code

/00 VSPG
/10 XP7

INST02-410
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-420

2.10 Obstacle part replacement procedure in install

2.10.1 Replacement procedure when PCB could not be restoring
(1)
The following messages are displayed when
PCB could not be restoring.
When “The PCB could not be restored
because the PCB type was incorrect. Target
PCB : ****” is displayed, please check the
PCB type. (The target PCB location is
displayed on Target PCB : ****.)

Please select(CL) [OK] after a check.

When “The PCB(s) could not be restored.

Target PCB : **** If this message is
displayed during MPB restore, please check
the HUBBOX” is displayed, please check the
PCB. (The target PCB location is displayed
on Target PCB : ****.)

Please select(CL) [OK] after a check.

NOTE: When “ONL4356E”, “ONL4357E” are displayed after the message, please remove
the Module according to the message.

(2)
“Are you sure you want to replace the PCB(s)
that could not be restored?” is displayed.

When the maintenance parts to replace exist,

please select (CL) [Yes]. → Go to (3).
When the maintenance parts to replace do not
exist, please select (CL) [No] and refer to
trouble shooting for errors in install. (INST02-110, INST02-150)

INST02-420
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-430

(3)
“Please replace the PCB(s), and then select
[OK]. Target PCB : ****” is displayed.
(The target PCB location is displayed on
Target PCB : ****.)

Please select (CL) [OK], after replacing the

target PCB.

It returns to the former INSTALLATION SECTION.

INST02-430
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-440

2.11 Trouble shooting at the time of new installation

(1) When the ALARM LED comes on
START

Dump or get a log.

(See page SVP02-09-10.)

Check the Power Event Log.

(See page SVP02-02-120.)

Yes
Is the Power Event Log reported
with all MP?

No

No
Is there no Power Event Log?

Yes
Power OFF
(See page INST03-14-50.)

Exchange the PCB(s) which have the

processor(s) that did not report the Power
Event Log with service parts.
(*1, *2)

Execute the New installation work again.

(See page INST02-10.)

Is the execution of No
a new installation a normal
termination?
Dump or get a log.
Yes (See page SVP02-09-10.)

END T.S.D. call

*1: Pulling out of the processor PCB

Refer to page INST04-05-390.
*2: Insertion of the processor PCB
Refer to page INST03-07-850.

INST02-440
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST02-450

(2) When the Logical path is detached

START

Dump or get a log.

(See page SVP02-09-10.)

Power OFF
(See page INST03-14-50.)

Set the Volatile Jumpers

on all the CM PCBs.

Refer to the SIM log regarding

the path detachment.

Replace the one PCB that is shown in the ACC in the state in
which the power is not applied to the PCB.

MP PCB: See page REP03-11-10.

CHA (Fibre channel): See page REP03-12-10.
CHA (Mainframe fibre channel): See page REP03-13-10.
DKA: See page REP03-14-10.
Cache: See page REP03-10-10.
However, the pre-processing and post-processing is not needed.

Power ON (PS ON).

(See page INST03-14-10.)

Is the Logical path detached? No

(See page SVP03-11-10.)

Yes Pull out the Volatile Jumpers

from all the CM PCBs.
Power OFF
(See page INST03-14-50.)
Erase the dump/log.
(See page SVP02-03-10.)
Did you perform
No the operation above for all the PCBs END
shown in the ACC?

Yes

T.S.D. call

INST02-450