Product Data Sheet

Metal Silicone 2* Sealant

Product Description
Metal Silicone 2 sealant is 100% waterproof and ideal for sealing metal substrates and
weatherproofing. This high performance and durable sealant offers a fast cure and can be
exposed to rain or water in as little as 30 minutes. Metal Silicone 2 sealant is permanently flexible,
shrink-proof, and crack-proof. It offers strong adhesion to metal substrates and will not blemish
most metal finishes. It can be applied to either wet or dry surfaces, is sun-proof and freeze-proof,
and will not breakdown or wash away. Backed by a lifetime guarantee.

Product Attributes
• Fast cure: 30-minute tack free and 24-hour full cure(1)
• 30-minutes rain and water exposure(1)
• 100% weatherproof, freeze-proof and sun-proof, will not degrade in harsh climates
• Meets ASTM C-920 Class 25 specifications
• Permanently flexible to keep gaps sealed, shrink-proof and crack-proof
• Will never break down due to extreme weather conditions
• Resist mold(2) with 10-year mold-free product protection
• Excellent adhesion for wet or dry applications(3)
• Will not blemish high-end metal finishes such as chrome, bronze and nickel
• Neutral curing sealant adheres to more surfaces including most metals, aluminum, and
stainless steel
• Freeze/thaw stability
• Non-paintable

(1) 3 0-minute tack free time, 24-hour full cure and exposure to rain or water possible in as little as 30 minutes with bead size
max 3/16”, temperature min 65°F and humidity min 50%. Otherwise, sealant should not be exposed to water for 8 hours.
Do not touch or clean caulk for 24 hours
(2) Cured sealant is resistant to stain-causing mold & mildew. Regular cleaning of sealant is required, however, as soap and
other residue can cause secondary mold and mildew growth
(3) For wet surface application, wipe off excess water before applying
* Silicone 2 is a trademark of Momentive Performance Materials Inc.
Page 1 of 6
 Product Data Sheet

Basic Uses
Metal Silicone 2* sealant is used in a wide variety of applications including, but not limited to steel sheds, metal roofs, trailers, recreational
vehicles, gutters, windows, doors, siding, trim, vents, pipes and other metal surfaces.

Adheres To
Common building materials including most metals, stainless steel, aluminum, copper, composites, brick, stone, stucco, concrete, cement,
masonry, cement board, most woods, glass, porcelain, ceramic tile, drywall, plaster, vinyl siding, PVC, fiberglass, and painted surfaces.
Excellent for most metal finishes such as chrome, bronze & nickel.

Metal Silicone 2 sealant should not be considered:

• For structural repairs
• For use underwater or in other applications where the product will be in continuous contact with water
• For use in food contact applications
• When painting of the cured sealant is desired
• For use on aquariums
• For use on surfaces with special coatings, such as mirrors, without approval of the article’s manufacturer
• Under exceedingly hot or cold conditions (see Sealant Application section for additional information)
• On frozen or contaminated surfaces
• On excessively basic or acidic substrates
• For use on surfaces that are above 120°F (49°C)

Packaging
Metal Silicone 2 sealant is currently available in 10.1 fl. oz. (299 mL) plastic caulking cartridges and 2.8 fl. oz. (82.8 mL) plastic squeeze tubes.
Plastic cartridges and squeeze tubes are packaged as 12 units in cardboard boxes. Cartridges are dispensed using a single component hand
or air-pressured caulking gun.

Metal Silicone 2 Sealant

Stock # Model # Color Product UPC Size Carton Size Coverage (3/16” bead)
GESIL2METAL GE5050 Metallic Gray 077027050509 10.1 fl. oz 12 each 51 Linear Feet
SIL2METAL GE285 Metallic Gray 077027002850 2.8 fl. oz 12 each 13 Linear Feet

Metallic Gray

* Silicone 2 is a trademark of Momentive Performance Materials Inc.

Page 2 of 6
 Product Data Sheet

Typical Properties
Typical physical property values of Metal Silicone 2* sealant as supplied and cured are set forth in the tables below.

Typical Properties Information – Supplied

Property Value Test Method
Consistency Paste
VOC (ex. water & exempt) < 28 g/L WPSTM C1454
CARB Chem Curing (n.a.) VOC < 3.0 wt%
Odor Light Ammonia
Work Life (tooling time) 5-10 minutes
Tack Free Time (@ 72°F (22°C), 50% RH) 30 minutes ASTM C679
Rain-Ready 30 minutes
Sag/Slump < 0.2 inches ASTM D2202

Typical Properties – Cured

Property Value Test Method
Hardness, Durometer (Type A Indenter) 15 ASTM D2240
Tensile Strength 145 psi ASTM D412
Elongation 347% ASTM D412
Specific Gravity 1.00
Joint Movement Capability ±25% ASTM C719
Service Temperature Range (after cure) -60°F to +400°F (-51°C to 204°C)
Weathering and U.V. Resistance Excellent 30 year Study
Full Cure Time 24 hours

Typical properties are average data and are not to be used as or to develop specifications.

Surface Preparation
• Surfaces must be clean, dry and sound prior to application of the sealant. All contaminants, impurities, or other adhesion inhibitors
(such as moisture/frost, oils, old sealants, soaps and other surface treatments, etc.) must be removed from the surfaces to which the
sealant is intended to adhere.
• For cleaning, a solvent-dampened clean rag usually produces the desired result. Isopropyl Alcohol (IPA) is a commonly used solvent and has
proven useful for most non-porous substrates. When handling solvents, refer to manufacturer’s SDS for information on handling, safety and
personal protective equipment.
• Architectural coatings, paints and plastics should be cleaned with a solvent approved by the manufacturer of the product or which does not
harm or alter the finish.
• Since porous materials can absorb and retain moisture, it is important to confirm that substrates are dry prior to application of the sealant.
• Cleaning of surfaces should be done within 1 to 2 hours of when the sealant is to be applied.

* Silicone 2 is a trademark of Momentive Performance Materials Inc.

Page 3 of 6
 Product Data Sheet

Masking
The use of masking tape is recommended where appropriate to ensure a neat job and to protect adjoining surfaces from over-application of
sealant. Masking tape should be removed immediately after tooling the sealant and before the sealant begins to skin over (tooling time).

Method of Application
Metal Silicone 2* sealant is easily dispensed from cartridges using standard caulk guns or air operated guns. Maximum recommended
pressure for air operated guns is 45 psi (3.2kgs/cm2). Mixing, heating and refrigeration not required.

Instructions
 emove dirt, grease, moisture, soap residue & old caulk from area to be sealed. Use backer rod for gaps larger than 1/2” X 1/2”
1. R
(12.7mm x 12.7mm)(1).
2. Cut nozzle to obtain desired bead size.
3. PIERCE INNER FOIL SEAL.
4. Using caulk gun, apply sealant into gap. Smooth the sealant into gap.
5. Wipe hands & tools thoroughly before washing.
6. Allow a minimum of 30 minutes before exposing sealant to water.
(1) S
 ealant depth should be controlled with a closed cell, non- gassing type backer rod. Backer rod should be slightly larger in diameter (25 to 50%) than the joint width.

Sealant Application
• Apply sealant in a continuous operation applying a positive pressure adequate to properly fill and seal the seam, cavity or joint.
• Tool or strike the sealant with a concave tool, applying light pressure to spread the material against the joint surfaces to ensure a
void-free application.
• When tooling, use care not to spread the sealant over the face of the substrates adjacent to the joint or masking as the silicone can be
extremely difficult to remove on rough or porous substrates. Excess sealant should be cleaned from glass, metal and plastic surfaces while
still uncured. On porous surfaces the excess sealant should be allowed to progress through the initial cure or set-up. It should then be
removed by abrasion or other mechanical means.
• If sealant is applied when the temperature is below 32°F (4°C) or if frost or moisture is present on the surfaces to be sealed, the rate of cure
will slow. For standard cure speed, apply in temperatures above 32°F.
• The cure rate of this product is dependent upon temperature and the availability of atmospheric moisture. Under average conditions
(relative humidity of 50 ±5% at an air temperature of 73.4 ±2°F [23 ±1°C]) this material can attain a cured thickness of 2-3 mm per 24 hours
(assuming ample access to atmospheric moisture). As temperature decreases, the cure rate slows down (and vice versa). Low moisture
environments will also reduce the cure rate. Near-confined spaces, which limit the overall access to atmospheric moisture, will cure only
from that surface which has access to the atmosphere.

Note:
• This material requires atmospheric moisture to cure from paste to rubber and may not attain its listed final cured rubber properties when
used in designs or applications where the silicone is encapsulated and without access to atmospheric moisture.
• Some materials that bleed plasticizers or oils can cause a discoloration on the surface of sealants. When sealing to or over items such as:
rubberized gaskets, bituminous based materials, butyl or oil-based products, oily woods, tapes, etc., compatibility testing prior to use
is recommended.
• Silicone materials are hydrophobic in nature and if inadvertently over-applied onto adjacent joint surfaces (even if removed immediately),
can create a waterproofing effect of a substrate when the substrate is wet. See section on Masking.

* Silicone 2 is a trademark of Momentive Performance Materials Inc.

Page 4 of 6
 Product Data Sheet

Specifications
Meets ASTM C-920, Type-S, NS, Class 25, Use NT, M, G, A & O Test Requirements.
Federal Specification TT-S-00230C, TT-S-001543A

Suggested References
In addition to the guidelines provided herein, Momentive Performance Materials recommends that designers and users of Metal Silicone 2*
sealant familiarize themselves with the latest editions of following industry guidelines and best practices:
1.) ASTM C1193 Standard Guide for Use of Joint Sealants.

Product Safety, Handling and Storage

Customers considering the use of this product should review the latest Safety Data Sheet and label for product safety information, handling
instructions, personal protective equipment if necessary, and any special storage conditions required. Safety Data Sheets are available at
www.GEsealants.com or, upon request, from any MPM representative. Use of other materials in conjunction with MPM sealants products
(for example, primers) may require additional precautions. Please review and follow the safety information provided by the manufacturer of
such other materials.

Patent Status
Nothing contained herein shall be construed to imply the nonexistence of any relevant patents or to constitute the permission, inducement
or recommendation to practice any invention covered by any patent, without authority from the owner of the patent.

Limitations
Customers must evaluate Momentive Performance Materials products and make their own determination as to fitness of use in their
particular application.

* Silicone 2 is a trademark of Momentive Performance Materials Inc.

Page 5 of 6
 Product Data Sheet

Customer Service Centers

Americas +1 (866) 275-4372

Email: [email protected]

Visit us at www.GEsealants.com

THE MATERIALS, PRODUCTS AND SERVICES OF MOMENTIVE PERFORMANCE MATERIALS INC. AND ITS SUBSIDIARIES AND AFFILIATES (COLLECTIVELY “SUPPLIER”), ARE
SOLD SUBJECT TO SUPPLIER’S STANDARD CONDITIONS OF SALE, WHICH ARE INCLUDED IN THE APPLICABLE DISTRIBUTOR OR OTHER SALES AGREEMENT, PRINTED ON THE
BACK OF ORDER ACKNOWLEDGMENTS AND INVOICES, AND AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION, RECOMMENDATIONS, OR ADVICE CONTAINED HEREIN
IS GIVEN IN GOOD FAITH, SUPPLIER MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (i) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE
CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING ITS PRODUCTS, MATERIALS, SERVICES, RECOMMENDATIONS OR ADVICE. EXCEPT
AS PROVIDED IN SUPPLIER’S STANDARD CONDITIONS OF SALE, SUPPLIER AND ITS REPRESENTATIVES SHALL IN NO EVENT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM
ANY USE OF ITS MATERIALS, PRODUCTS OR SERVICES DESCRIBE HEREIN. Each user bears full responsibility for making its own determination as to the suitability of Supplier’s
materials, services, recommendations, or advice for its own particular use. Each user must identify and perform all tests and analyses necessary to assure that its finished
parts incorporating Supplier’s products, materials, or services will be safe and suitable for use under end-use conditions. Nothing in this or any other document, nor any
oral recommendation or advice, shall be deemed to alter, vary, supersede, or waive any provision of Supplier’s standard Conditions of Sale or this Disclaimer, unless any such
modification is specifically agreed to in a writing signed by Supplier. No statement contained herein concerning a possible or suggested use of any material, product, service
or design is intended, or should be construed, to grant any license under any patent or other intellectual property right of Supplier covering such use or design, or as a
recommendation for the use of such material, product, service or design in the infringement of any patent or other intellectual property right.

GE is a trademark of General Electric company. Used under trademark license.

Momentive and the Momentive logo are trademarks of Momentive Performance Materials Inc.
*Silicone 2 is a trademark of Momentive Performance Materials Inc.
Copyright 2020 Momentive Performance Materials Inc. All rights reserved.

GEsealants.com

CDS: DataMetalSilicone2Sealant (02/20) 161-163-00E-GL Page 6 of 6