USER MANUALS

C-SERIES 2

M-SERIES 3

R-SERIES 4

T40 5-6

T40X 7-8

T-SERIES Aadapters 9-11

OMS 12-13

Leg Platform 14

Paddle GEN II 15

X3 Adapter 16
 C-SERIES ASSEMBLY INSTRUCTIONS

C
-S
E
R
IE
S
CAUTION! Do not adjust the platform or make any
changes to it, while there is a firearm in the holster.

All of our attachments can be used with any of our holsters.

Use the following instructions to assemble your attachments

Molle Paddle Paddle Gen II Belt Loop Low Ride

ORPAZ ATTACHMENTS INSTALLATION

1. Align the holster mounting inserts 2. Firmly hand tighten the screws.
with the holes on the attachment.

3. Adjust the rotation of the holster to 4. Use the retention screw to set the
your desired position and than tighten retention of the holster.
the screw.

Contact us at : [email protected]
WWW.ORPAZDEFENSE.COM
 M-SERIES ASSEMBLY INSTRUCTIONS

M
-S
E
R
IE
S
CAUTION! Do not adjust the platform or make any
changes to it, while there is a firearm in the holster.

Molle Paddle Paddle Gen II Belt Loop Low Ride

ORPAZ M-SERIES - OWB INSTALLATION

1. Use an allen key to loosen the IWB 2. Take off the back surface cover. 3.Align the holster mounting inserts with
Clip. Take off the back surface cover. Attach it at the front - This will cover the the holes on the attachment.
front mounting inserts

4. Adjust the rotation of the holster to 5.Use the retention screw to set the
your desired position. retention of the holster.
Than Firmly hand tighten the screws.

Contact us at : [email protected]
WWW.ORPAZDEFENSE.COM
 ASSEMBLY INSTRUCTIONS

R
-S
E
R
IE
S
CAUTION! Do not adjust the platform or make any
changes to it, while there is a firearm in the holster.

All of our attachments can be used with any of our holsters.

Use the following instructions to assemble your attachments

Molle Paddle Paddle Gen II Belt Loop Low Ride

ORPAZ ATTACHMENTS INSTALLATION

1. Align the holster mounting inserts 2. Firmly hand tighten the screws.
with the holes on the attachment.

3. Adjust the rotation of the holster to 4. Use the retention screw to set the
your desired position and than tighten retention of the holster.
the screw.

Contact us at : [email protected]
WWW.ORPAZDEFENSE.COM
 ASSEMBLY INSTRUCTIONS

WARNING : Read and understand the instructions

thoroughly before adjusting your holster
Before adjusting your orpaz holster, make sure to engage
the safety, remove the magazine and make sure that
the weapon is unloaded with no magazine in the well.
Be certain the pistol is pointed in a SAFE direction so
that no other persons are endangered. ensure that your
fingers or other parts of the hands and face are kept away
from the slide.

1
 ASSEMBLY INSTRUCTIONS

Before adjusting your Orpaz holster, make sure your pistol is

checked clear and safe

The T40 can be used with All of our attachments.

Follow the instructions to assemble your attachments.

Molle Paddle Paddle Gen II Belt Loop Low Ride

To set the retention of your Orpaz T-40, place your pistol Use an Allen key to loosen the back screws and adjust the
1 firmly into the holster. The barrel of your pistol will touch 2 width of the holster
the magnet

Use an Allen key to adjust the spring screw, This will adjust the Be aware while adjusting the height of the holster to keep at least
3 height of the holster. 2mm between the slide of your pistol and the flipper.

B
A

Attachment installation - Align the attachment with the mounting

5 holse on the holster-Firmly hand tighten both screws

2
 ASSEMBLY INSTRUCTIONS

Before adjusting your Orpaz holster, make sure your pistol is

checked clear and safe

The T40X can be used with All of our attachments.

Follow the instructions to assemble your attachments.

Molle Paddle Paddle Gen II Belt Loop Low Ride

To set the retention of your Orpaz T-40X, place your pistol

Use an Allen key to loosen the back screws and adjust the width of
1 firmly into the holster. The barrel of your pistol will touch
the magnet
2 the holster

Use an Allen key to adjust the spring screw, This will adjust the Be aware while adjusting the height of the holster to keep at least
3 height of the holster. 2mm between the slide of your pistol and the flipper.

B
A

Attachment installation - Align the attachment with the

4 Adjust the lower back spring screw to secure your flashlight 5 mounting holse on the holster-Firmly hand tighten both screws

2
 ASSEMBLY INSTRUCTIONS

LEG-PLATFORM ADAPTER

Connect the adapter between the holster and the leg platform. Place the screws in the correct order, tighten both screws firmly
1 Ensure that the position and orientation are correct 2 Do not overtighten

Parts

Pan head Pan head

screw with meson screw

FLASHLIGHT ADAPTER
If you are using a TLR1 / Surefire X300 or a similar dimension flashlight (height less than 1.83 in. (4.64 cm),
the attached spacer will keep your flashlight secure and prevent movement in your holster.

1. Take out the screws from the spacer.(A) Once both pins are in place, and the spacer is stable, Firmly
1 Make sure the spacer orientation is correct. (B) 2 hand tighten both screws
Insert the spacer firmly into its place. (C)

A B C Parts

Screw*2

Spacer

SUB COMPACT PISTOLS EXTENTION

If you're using a subcompact pistol, this extension is necessary to ensure a good fit

Insert the magnet into the extension, then connect everything

1 Loosen the Phillips screw and take out the magnet. 2 together using the long Phillips screw.

Parts

Magnet

Adapter

M4-20mm
Phillips screw

Contact us at : [email protected]
WWW.ORPAZDEFENSE.COM

3
 ORPAZ T-SERIES ADAPTERS

USER MANUAL

CAUTION : This manual contains important information on proper assembly, fit, and replacement of
parts. Read and follow the instructions carefully before installing the
adapters. Incorrectly installing will harm the gear or may cause minor injury to the user Ensure there is
no firearm in the holster when installing, modify, disassemble or remove any part from the Holster.

Orpaz Holster designs vary according to specific firearms.Users have to verify that the holster fits their
firearm. Before using the holster make sure your pistol is checked, clear,and safe, with no magazine in the
well. Do not use a loaded handgun with any ORPAZ Holster without first testing in the unloaded condition,
Do not carry any pistol with a round in the chamber unless you have received professional training. When
drawing, testing or adjusting your holster, keep your
finger away from the trigger, Be sure your safety is engaged, and keep the gun pointed in a safe direction.
Drawing and holstering a firearm can be dangerous with risk of personal injury or death. You must seek
proper instruction and training, Always use your firearm as recommended by the manufacturer.

Contact us at : [email protected]
WWW.ORPAZDEFENSE.COM
 T-SERIES ADAPTERS

SUB COMPACT PISTOLS EXTENTION

TO BE USED WITH : T40 | T40X

If you're using a subcompact pistol, this extension is

necessary to ensure a good fit in your holster.

Loosen the Phillips screw and take out the magnet. Insert the magnet into the sub compact extention, then connect
everything together using the long Phillips screw.
Parts

Magnet

Adapter

M4-25mm
Phillips screw

LEG PLATFORM ADAPTER

TO BE USED WITH : T40 | T40X | T41

The adapter is required when mounting a T-series holster on a Leg

platform. It makes contact between the components and creates a
space between the holster and the Leg platform.

1. Connect the adapter between the holster and the leg platform. 2.Place the screws in the correct order, and tighten both
Ensure that the position and orientation are correct. (FIG. 1&2) screws firmly. (FIG.3) Do not overtighten.
Parts

Pan head
screw

Pan head
with meson screw
Fig.2
Fig.1

Fig.3

T40X FLASHLIGHT SPACER

TO BE USED WITH : T40X

If you are using a TLR1 / Surefire X300 or a similar dimension

flashlight (height less than 1.83 in. (4.64 cm), the attached spacer will
keep your flashlight secure and prevent movement in your holster.

1. Take out the screws from the spacer.(A)

Make sure the spacer orientation is correct (look for “UP”). (B) 2. Once both pins are in place, and the spacer is stable,
Insert the spacer firmly into its place. (C) firmly hand tighten both screws.
B C Parts

Screws

Spacer
 T-SERIES ADAPTERS

PASSIVE RETENTION MECHANISM REPLACEMENT

TO BE USED WITH : T40 | T40X

The replacement of the Passive retention mechanism enables

you to perfectly customize your holster to fit your needs.

(A) Using the Allen key, loosen the (B) Put the magnet (C) Assemble the screw and (D) Slide it to the correct position, and tighten
bottom hex cap screw. The magnet aside, and keep the the spring respectively onto it firmly by hand. Adjust the height according
retention unit will come out. screw and spring. the new retention adapter. to the assembly instructions.

B C D

PASSIVE RETENTION TYPES

PASSIVE RETENTION ADAPTER SAFETY ADAPTER
If you wish to remove the magnetic The safety adapter enables you to use
retention, this adapter will keep your your holster while training with a safety
pistol secure by using a plug. Chamber Plug Installed on your pistol.

MAGNET RETENTION ADAPTER THREADED BARREL EXTENTION

The default magnetic retention holds For guns with threaded barrels and pistols with
your pistol firmly and provides optimal longer slide lengths than 7.5”, This extension allows
security in your holster. you to carry longer pistols in the holster.
 OMS USER MANUAL OMS RECEIVERS

Read and understand entire manual before using this product The OMS receivers are designed to accept any accessory with
WARNING Orpaz Holster designs vary according to specific firearms, Users must
an OMS insert. Each receiver is specially designed to meet
verify that the holster fits their firearm. Before using the holster make sure your pistol specific needs and gives you the freedom to rearrange your gear
is checked, clear, and safe, with no magazine in the well. Do not use a loaded on different mounting points without the use of tools. Remove,
handgun with any ORPAZ accessory without first testing in the unloaded condition, Do change, and attach it according to your needs within seconds.
not carry any pistol with a round in the chamber unless you have received professional
training. When drawing, replacing, or holstering your gun on different mounting
locations, keep your finger away from the trigger, Be sure your safety is engaged, and
keep the gun pointed in a safe direction. Drawing and holstering a firearm can be
dangerous with risk of personal injury or death. You must seek proper instruction and OMS Paddle
training, Always use your firearm as recommended by the manufacture. Do not modify
disassemble or remove any part from the OMS or any Orpaz holsters. Slightly curved to the natural shape of
your body, with minimal footprint and
grips to hold tightly to your belt. The
OMS Paddle Receiver is a classic OWB
OMS INSERTS carry option.

The OMS features two types of inserts:

1.OMS Holster insret OMS Belt Loop

The OMS Insert can be attached to any Orpaz Orpaz classic OWB carry option, Fits
accessory with a matching hole pattern such as on all belts up to 2’, designed with
Holsters, Magazine pouches, Law enforcement minimal footprint and grips to hold
gear etc’. It will mount on any OMS Receiver and tightly to your belt.
features a special locking release mechanism
and adjustable cant. Customize and transfer
your gear to different mounting locations within
seconds.
OMS Molle
Transform your Molle platform to be
versatile and customizable. Compatible
with all MOLLE systems
Attach any accessory you want quickly
and easily without having to deal with
Molle straps.

OMS Low Ride

Specially designed ergonomic structure,
2.OMS Molle insret allows you to mount your Holster at lower
The OMS Molle insert can be attached to any gear level and allows a quick draw when
with the Molle mil-spec system, such as bags, needed. Commonly picked by tactical
pouches, first-aid kits etc, and transforms them and Law enforcement units.
to be versatile and modular. Mount your MOLLE
equipment on any OMS Receiver you want,
without having to deal with Molle straps,
configure it only once, and you're ready for any
mission.

OMS Leg Platform

Secure, ergonomic, adjustable with
minimal footprint and maximum
functionality.
Designed to meet tactical needs
and mobility.
 OMS ASSEMBLY INSTRUCTIONS QUICK START GUIDE

OMS Holster Insert How to mount your gear on an OMS receiver.

1.Align the holster mounting inserts 2.Make sure the cant is set to your
with the holes on the OMS Insert. preference and firmly hand tighten 1.Pull the latch while turning it sideways, so it remains open.
Firmly hand tighten the screws. the screws.

2. Align the insert with the receiver's locking holes (A) Slide
the insert down until it stops in place.(B)
OMS Molle Insert A
How to attach your OMS MOLLE insert to a MOLLE-compatible equipment
( pouches, carriers, First-aid kits, pouches etc)

Thread all four edges of the insert underneath the MOLLE webbing at the
same time- All four edges must be threaded properly.

4. Push the latch back in place to lock the insert into the
receiver.

The safety locking adapter locks the insert securely to the Molle webbing.
(A)- Thread it under the webbing .
(B)- Align it with the Insert's Locking hole, and slide it into place

A B B

We value the relationships we have with our consumers, and

we encourage you to contact us with any questions,
comments, or feedback you have.

Contact us at : [email protected]
WWW.ORPAZDEFENSE.COM
 ASSEMBLY INSTRUCTIONS

ORPAZ LEG PLATFORM

DOUBLE MAGAZINE EXTENTION
CAUTION! DO NOT adjust the platform or make any
changes to it, while there is a firearm in the holster.

1.Start by loosening the upper LEG PLATFORM HOLSTER INSTALLATION

strap.
2.Make sure you have access to 3. Remove the nuts from 4. Align the holster mounting
the screws. the screws. inserts with the holes on the
platform. Firmly hand tighten
the screws.

LEG PLATFORM DOUBLE MAGAZINE EXTENTION INSTALLATION

2.Start by detaching the nuts 3. Separate the fabric platform 4. Firmly hand tighten the
and the screws of the double and the plastic. screws.
magazine Extension. Align the mounting holes with the
holes on the Leg platform.

BUY NOW

Double magazine
Extension

Contact us at : [email protected]
WWW.ORPAZDEFENSE.COM
 ASSEMBLY INSTRUCTIONS

CAUTION! Do not adjust the platform or make any

changes to it, while there is a firearm in the holster.

PADDLE GEN II
The Paddle Gen II attachment can holds any two Orpaz accessories

1. Align the holster or any other Orpaz accessorie mounting inserts with
the holes on the paddle Gen II

2. Firmly hand tighten the screws.

PARTS

M5 -7mm ×3

Allen Key

Disk×2
-Upper holes only

Contact us at : [email protected]
WWW.ORPAZDEFENSE.COM
 ASSEMBLY INSTRUCTIONS

CAUTION! Do not adjust the platform or make any

changes to it, while there is a firearm in the holster.

ADAPTER X3
Attach any combination of accessories that you want
to your belt with the X3 Adapter.

1 . Align your accessories with the Adapter X3 according to

your preference. The mounting inserts should line up with the
holes on the Adapter X3.
PARTS

M5 -7mm ×3 M5 -12mm ×1

Disk×2 Allen Key

Upper holes only

2.Tighten all screws firmly by hand.

Contact us at : [email protected]
WWW.ORPAZDEFENSE.COM