Programming of Gearless Elevator Control Boards

- Press (+ or -) to select the mode

Basic Programming Program P4 : Door Type P4> DOOR TYPE
(On) or (Off).
Program P14 : CAM Trials P14>CAM Trials Program P20 : Active Floor P20>Active Floor Program P25 : Restore Selector P25>Restore Sel.
- Press RESET button for 2 This program is used to select the used door type. This program adjusts the number of CAM trials This program is supposed to correct the selector
ULTIMATRUE - The supervisor mode (On) will Supervisor
This program can enable or disable every landing
seconds, and then press and hold
XC-8GL Y20M8 V7.30 - Press ENTER to access this keep the control board out of 1 on after which the control board will suspend operation. or car call button independently.This function is counter by going to the ground floor when the
ENTER during the appearance of Door: Manual
program or (+ or -) to select function displaying fast time error Selecting ‘0’, means that the control board will useful for intentionally making certain floor(s) out power is off and back again
welcome message. The second another program. drop all calls after the default CAM action and the of service. EXTERNAL stands for landing calls
line contains production and
even if the board is reset, while Supervisor - Press ENTER to access this
- After accessing this program, supervisor mode (Off) will make 0 off
control board can accept reregistering calls and while INTERNAL stands for car calls. program or (+ or -) to select another Restore selector
version information. Door:
press (+ or -) to select the used Wait- Close the control board work normally if it repeating the CAM action indefinitely. - Press ENTER to access this program. 0 off
When the next screen appears, door type. is reset. - Press ENTER to access this program or (+ or -) program or (+ or -) to select - After accessing this program,
release the ENTER button then PRESS (+) KEY - When finished, press ENTER Door: To quit the supervisor mode (On) and return to to select another program. another program. press (+ or -) to select the mode Restore selector
Press (+) button to go to the Wait- Open After accessing this program, (On) or (Off). 1 on
to save and go to next program. normal mode of operation, the board must enter the -After accessing this program, Floor 0:external
password screen: maintenance mode and exit it. press (+ or -) to set the required Cam trials:0 press (+ or -) to set the required 0 off - When finished, press ENTER to
Program P5 : System Type P5> SYSTEM TYPE This action ensures that a qualified person CAM trials from 0 to 10 times. parameter as preferred. save.
- Enter the password using (+) or ENTER
supervised the cause of fast time error before Floor 0:external
PASSWORD This program is used to select - When finished, press ENTER to save and go to OFF: indicated floor number call Program P26: Service Control P26>SERVICE CTRL
(-) buttons. To go to next digit, getting the elevator in normal operation again. 1 on
00000 the system type. next program. button will be disabled internally
press ENTER.
- When finished, press ENTER to save and go to or externally. This program enables the operator to control the
Notice: Factory setting password is (00000). - Press ENTER to access this Program P15 : Fork Time P15>Fork Time elevator in service mode using programming
System:
next program. ON: indicated floor number call
- After entering the correct password and press- program or (+ or -) to select buttons, so that (+) button is used to move the car
ing ENTER, the user will be directed to the basic Two Speed This program adjusts the time duration where the button will be enabled internally
another program. Program P11 : in the UP direction and (-) button is used to move
P11> LAMP TIME elevator remains idle and there is registered calls or externally. Floor 0:external
program mode. - After accessing this program, System: Time of Cabin Lighting the car in the DOWN direction
and the door contact is open. After this time, all Press code
Program P1 : Floor Number P1>Floor Number press (+ or -) to select the Three Speed - After choosing, press ENTER
calls are canceled. - Press ENTER to access this
used system type. This program adjusts the time for the car light. then press (+ and -) together to
Determining number of active doors (stops). - Press ENTER to access this program or (+ or -) - Press ENTER to access this program or (+ or -) confirm selection. program or (+ or -) to select another
Number of active doors can be determined up to - When finished, press ENTER to select another program. to select another program. program.
to save and go to next - When finished all floors, press
16 doors (stops). - After accessing this program After accessing this program,
program. Fork Time:4 ENTER to save and go to next - After accessing this program, MANUAL SERVICE
- Press ENTER to access this program or (+ or -) press (+ or -) to set the required Lamp Time: 8 press (+ or -) to set the required program. press (+) to activate this program, 0 OFF
to select another program. Program P6 : Collective P6> COLLECTIVE time from 1 to 90 seconds. time from 1 to 4 minutes. press Enter to save, then this
- When finished, press ENTER to save and go to Program P21 : Lock Error P21>Lock Error MANUAL SERVICE
- Press (+ or -) to determine number of floors, and - When finished, press ENTER to save and go to screen will appear:
1 ON
This program is used to select the method of next program.
then press ENTER after selection for saving. next program. This program can enable or disable the lock error - Press ENTER to switch the speed
serving landing calls
- Floor numbers start from zero, thus for - PressENTER to access this program or (+ or -) Program P12 : Emergency P12>EMERGENCY Program P16 : Park Time P16>Park Time function This function is useful for continuously of the elevator before moving the F2 S4 SLOW : :
monitoring the lock contact during each call ERR: SERV 8
programming 8 floors (stops) select 7, and for car.
to select another program. This program adjusts the period of time during
This program adjusts the preference of using built service at any Floor. For moving the car, (+) or (-)
programming 16 floors (stops) select 15. - After accessing this program, press (+ or -) to which the elevator remains idle with no registered F2 S4 FAST : :
in emergency actions that will control the inverter This feature is supposed to ensure safety of the buttons are used according to the
Floor No.: 7 calls. After this period, the elevator will move ERR: SERV 8
select the required collective type. in case of power loss. door lock when activated. desired direction.
Program P2 : Display Mode automatically to a preset parking f loor.To cancel
P2> DISPLAY MODE DOWN COLL.: serving calls in down Collective: - Press ENTER to access this program or (+ or -) to In this sense, it is necessary to open lock contact
- When finished, press RESET to
this feature, adjust the park time to a value more at every time the car stops on a floor. In case of
direction only. Down coll. select another program. exit this mode.
Determine type of display used with points A~H. than 29 minutes. The screen will show ‘0 OFF’
SEMI COLL. : serving calls in up and Collective: - After accessing this program, press (+ or -) to
not opening of the lock contact, the car will not
- Press ENTER to access this program or (+ or -) down directions.
message. move to ensure passengers safety. Important Notes
Semi coll. select the mode (On) or (Off). - Press ENTER to access this program or (+ or -)
to select another program. APB: serving one request at a time. - Press ENTER to access this
Display: Collective: - After selecting the (On) mode, to select another program. - All numbers on the screen are pre-factory
- After accessing this program, 7SEGMENT - When finished, press ENTER to Emergency: program or (+ or -) to select Lock error:
APB
press (+ or -) to select the suitable save and go to next program. press (Enter) to set the time which 1 ON - After accessing this program another program. After access- 0 off settings
park time:4
the board waits after the power is press (+ or -) to set the required ing this program, press (+ or -) to
display mode that will be used. Emergency: 1 on
In case of selecting 7segment or Program P7 : Wait Time P7> WAIT TIME off and start to turn on the RN time from 1 to 29 minutes. set the required parameter as
0 OFF Lock error:
Display: Relay, press (+) or (-) to set this - When finished, press ENTER park floor:0 preferred.
binary display mode, the floor 1 on
Floor Wire This program adjusts the time that the car will wait time from 4 to 50 seconds. to save and go to next program.
coordination screen will appear so
when arriving at a f loor before moving again to - After choosing, press ENTER
that the user will adjust the required - When finished, press (Enter) to then press (+ and -) together to Lock error:
serve the next call. set the time between operating the Program P17 : P17>OPER.TIMEOUT Press code
number to be displayed when the EMR Time: 4 confirm selection.
Display: - Press ENTER to access this program or (+ or -) RN Relay and the start of the OPER.TIMEOUT
car is at this floor.
Binary NEG to select another program. - When finished, press ENTER
- Note that the left side digit emergency signal, RN EMR: 5 sec
This program adjusts the period of time after
to save and go to next program.
(tens) can be assigned a value of - After accessing this program, press - press (+) or (-) to set this time which the control board will stop working.
Wait time: 4 EMR UP: 2 sec
‘none’ or ‘1’, while the right side Display: (+ or -) to set the required time from 2 from 1 to 20 seconds. This function is useful for forced routine Program P22 : Max Calls P22>Max Calls
digit (units) can be assigned a Binary POS to 30 seconds. - When finished, press (Enter) to set the time
maintenance check.
This program can select the maximum number of
value from these characters ‘0, 1, - Press ENTER to access this program or (+ or -)
- When finished, press ENTER to between operating the emergency signal and car calls that can be registered at a time.
2, 3, 4, 5, 6, 7, 8, 9, F, G, P, - or save and go to next program. starting to operate the UP-direction signal, press (+)
to select another program.
This feature is supposed to secure the elevator
space’. or (-) to set this time from 0 to 20 seconds. - After accessing this program,press from mess of kids, where registering of car calls
Oper.timeout:
Program sequence is as follows: Program P8 : CAM Time P8> CAM TIME (+ or -) to set the required parameter. 0 off more than the preset max calls cannot be
- When finished, press ENTER to save and go to OFF: board will operate indefinitely.
- Press (+) or (-) to change the left digit. This program adjusts the waiting time from the next program. accepted.
ON: board will operate for the Oper.timeout: - Press ENTER to access this program
- Press ENTER to go to the right digit. Floor 0: 0 beginning of CAM working till lock closure. defined period. 1 on
Program P13 : KeyCode P13> KeyCode or (+ or -) to select another program. Max calls:
- Press (+) or (-) to change the right digit. - Press ENTER to access this program The ON selection will initiate the After accessing this program, press 0 off
or (+ or -) to select another program. period screen to adjust the Period:
- When finished, press ENTER and a ‘Store’ This program adjusts the preference of using built 1 month
(+ or -) to set the required parameter
message will appear temporarily. - After accessing this program, in car call buttons as a three digit access control operation period from 1 to 6 months. as preferred.
Max calls:
- Press ENTER again to save the number and go press (+ or -) to set the required code entry keypad. RESTART: operation time will be - After choosing, press ENTER then 4 calls
to next floor or (+ or -) if you want to readjust the time from 2 to 10 seconds for manual Cam Time: 3 The selected code sequence should be selected reset and disabled. Oper.timeout: press (+ and -) together to confirm
doors. 2 restart
same floor. within the range of operating doors (car call - When finished, press ENTER to selection.
For Automatic doors, the user can Cam Open: 3
- Repeat the previous steps, until all floors are buttons). save and go to next program. - When finished, press ENTER to Max calls:
assigned the required display pattern. select different periods of time for Cam Close: 3 Press code
- Press ENTER to access this program or (+ or -) save and go to next program.
opening and closing the door. Program P18 : Service Tel. P18>Service Tel.
to select another program. Program P23 : Fire Man P23>Fire Man
Program P3 : Serial Display P3> LED MATRIX - When finished, press ENTER to - After accessing this program, press (+ or -) to This program adjusts the service company
This program is used for assigning the required save and go to next program. select the mode (On) or (Off). telephone number so that it can be displayed on This program can enable/disable the fireman
two character alphanumeric combination for the board LCD in case of errors that stops the actions taken in case of fire alarm signal. The fire
Program P9 : Slow Time P9> SLOW TIME - When selecting (On) mode, you
floor is the default floor that the elevator
each floor that will be used with the RS232 serial will be directed to a screen to adjust elevator from working normally.
display. This program adjusts the maximum time for moving KeyCode - Press ENTER to access this program or (+ or -) automatically will go to in case of fire.
the required access sequence. 0 OFF
the car with the slow speed, after which the car will be to select another program. Press ENTER to access this program or (+ or -) to
Note : that only ULTIMATRUE’S serial display can Press (+ or -) to change the first digit,
select another program.
stopped automatically. and then press ENTER to move and KeyCode
be used. 1 ON
- After accessing this program, Service tel.
- Press ENTER to access this program or (+ or -) - Press ENTER to access this program adjust the second and third digit. press (+ or -) to set the required 000000000000 - After accessing this program, press
fire floor:0
telephone digit by digit. (+ or -) to set the required parameter
to select another program. or (+ or -) to select another program. - When finished, press ENTER to
as preferred.
- When using the serial display, - After accessing this program, press save and go to next program. - When finished, press ENTER to fire man:
- After choosing, press ENTER then
complete ASCII printable characters (+ or -) to set the required time from 4 Slow Time: 8 save and go to next program. 1 on
are available for assigment to each of
Floor 0: 0 to 25 seconds. Advanced Programming press (+ and -) together to confirm
the two digits,thus offering a very big Program P19 : Set Password P19>Set Password selection.
- When finished, press ENTER to save - Press RESET button for 2
symbol/character combination for any seconds, and then press and hold ULTIMATRUE This program enables you to change the password - When finished, press ENTER to fire man:
floor. and go to next program. XC-8GL Y20M8 V7.30 save and go to next program. Press code
ENTER during the appearance of to log into the two programming modes.
- After accessing this program, press (+ or -) to welcome message. The second - Press ENTER to access this program or (+ or -)
adjust each digit location as follows: Program P10 : Fast Time P10> FAST TIME line contains production and to select another program. Program P24 : Factory Set P24>Factory Set

- Press (+) or (-) to change the left digit. This program adjusts the maximum time for version information. - After accessing this program, This program is used to restore all control board
moving the car with the fast speed, after which - When the next screen appears, press (+ or -) to set the first digit of settings to its factory defaults.
- Press ENTER to go to the right digit. Basic password
the car will be stopped automatically. release the ENTER button then PRESS (+) KEY the basic password. >>00000<< - Press ENTER to access this
- Press (+) or (-) to change the right digit. Factory set:
- Press ENTER to access this Press and hold (-) button then - Press ENTER to move to the program or (+ or -) to select another Press code
- When finished, press ENTER and a ‘Store’ program or (+ or -) to select press the (+) button to go to the next digit and adjust it. program.
message will appear temporarily. another program. password screen:
- Repeat the same sequence for Advanced - After accessing this program,
- Press ENTER again to save the number and - After accessing this program, - Enter the password using (+) or ENTER the five digits. password
press (+ and -) together to confirm Factory set:ok
go to next floor or (+ or -) if you want to readjust Fast Time: 15 (-) buttons. To go to next digit, PASSWORD >>00000<<
press (+ or -) to set the required 00000 - Press ENTER to save and go to selection.
the same floor. time from 10 to 90 seconds. press ENTER. - When finished, press ENTER
advanced password setting.
- Repeat the previous steps, until all floors are - By pressing ENTER you will go to supervisor step Notice: Factory setting password is (00000). to save and go to next program. www.ultimatrue.com
assigned the required display pattern. selection to specify how to get back to the normal - After entering the correct password and press- Enter the required password in the same manner [email protected]
mode of operation in case of fast time error. ing ENTER, the user will be directed to the of the basic password.
advanced program mode. - When finished, press ENTER to save and go to
next program.
 ‫ﺑﺮﻣﺠﺔ ﻛﺮوت اﻟﺘﺤﻜﻢ ﻓﻰ اﻟﻤﺼﺎﻋﺪ اﻟﺠﯿﺮﻟﺲ‬

‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P26 (26‬اﻟﺘﺤﻜﻢ ﻓﻲ ﺻﯿﺎﻧﺔ اﻟﻤﺼﻌﺪ‬ ‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P20 (20‬إﻟﻐﺎء دور ﻣﻦ اﻟﺨﺪﻣﺔ‬ ‫اﻟﺒﺮﻣﺠﺔ اﻟﻤﺘﻘﺪﻣﺔ‬ ‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P8 (8‬زﻣﻦ ﻋﻤﻞ اﻟﻜﺎﻣﺔ‬ ‫اﻟﺒﺮﻣﺠﺔ اﻷﺳﺎﺳﯿﺔ‬
‫وﺑﺗﻔﻌﯾل ھذا اﻟﺑرﻧﺎﻣﺞ ﯾﻣﻛن ﺗﺣرﯾك اﻟﻣﺻﻌد‬ ‫‪P20>ACTIVE FLOOR‬‬ ‫ﯾﻣﻛن إﻟﻐﺎء دور أو أﻛﺛر ﻣن اﻟﺧدﻣﺔ‬ ‫‪P8> CAM TIME‬‬ ‫وھو اﻟزﻣن ﺑﯾن ﺑداﯾﺔ ﺷد اﻟﻛﺎﻣﺔ‬ ‫اﺿﻐط ﻋﻠﻰ زر ‪ RESET‬ﻟﻣدة ﺛﺎﻧﯾﺗﯾن ﺛم اﺿﻐط ﻋﻠﻰ زر ‪ENTER‬‬
‫اﺿﻐط ﻋﻠﻰ زر ‪ RESET‬ﻟﻣدة ﺛﺎﻧﯾﺗﯾن ﺛم اﺿﻐط ﻋﻠﻰ زر ‪ENTER‬‬
‫‪P26> SERVICE CTRL‬‬ ‫ﺻﯾﺎﻧﺔ ﺑﺎﺳﺗﺧدام أزرار اﻟﺑرﻣﺟﺔ‬ ‫ﻋن طرﯾﻖ ﻋدم اﻻﺳﺗﺟﺎﺑﺔ ﻟطﻠب اﻟﻣﺳﺗﺧدم ﻋﻧد‬ ‫واﻧﺗظﺎر ﻏﻠﻖ اﻟﻛﺎﻟون‪.‬‬ ‫أﺛﻧﺎء ظﮭور ﺷﺎﺷﺔ اﻟﺗرﺣﯾب اﻟﻣوﺿﺣﺔ ﺑﺎﻟﺷﻛل‪.‬‬
‫أﺛﻧﺎء ظﮭور ﺷﺎﺷﺔ اﻟﺗرﺣﯾب اﻟﻣوﺿﺣﺔ ﺑﺎﻟﺷﻛل‪.‬‬
‫‪-‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول إﻟﻰ اﻟﺑرﻧﺎﻣﺞ‪،‬‬ ‫ﺗﺳﺟﯾل ھذه اﻟطﻠﺑﺎت اﻟداﺧﻠﯾﺔ أو اﻟﺧﺎرﺟﯾﺔ وﯾﻣﻛن‬ ‫‪ULTIMATRUE‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺳﺗظﮭر اﻟﺷﺎﺷﺔ‬ ‫ﺳﺗظﮭر اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪-:‬‬
‫ﺳﺗظﮭر اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪-:‬‬ ‫‪ULTIMATRUE‬‬
‫ﺳﺗظﮭر اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪:‬‬ ‫إﻋﺎدة ﺗﺷﻐﯾﻠﮭﺎ ﻣرة أﺧرى‪.‬‬ ‫‪XC-8GL Y20M8 V7.30‬‬
‫‪Cam Time: 3‬‬ ‫اﻵﺗﯾﺔ‪:‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ زر ) ‪ ( +‬ﺳوف ﺗظﮭر ﺷﺎﺷﺔ ‪XC8-GL Y20M8 V7.30‬‬
‫‪ -‬اﺿﻐط ﻋﻠﻰ زر )‪ (-‬ﺛم )‪ (+‬ﻣﻌﺎ ﺳوف ﺗظﮭر‬
‫وھذه اﻟﺷﺎﺷﺔ ﺗﻌﻧﻲ أن اﻟﺧﺎﺻﯾﺔ ﻏﯾر ﻣﻔﻌﻠﺔ‪.‬‬ ‫ﯾﺗم ﺑرﻣﺟﺔ اﻟطﻠﺑﺎت اﻟﺧﺎرﺟﯾﺔ ‪ External‬أوﻻ‪:‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﺣدﯾد اﻟزﻣن ﻣن‬ ‫إدﺧﺎل اﻟرﻗم اﻟﺳرى‪.‬‬
‫‪MANUAL SERVICE‬‬ ‫ﺷﺎﺷﺔ إدﺧﺎل اﻟرﻗم اﻟﺳرى‬
‫‪0‬‬ ‫‪OFF‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬ﻟﺗﻔﻌﯾل اﻟﺧﺎﺻﯾﺔ وﺟﻌﻠﮭﺎ‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺳﺗظﮭر‬ ‫‪PRESS (+) KEY‬‬ ‫‪ 2‬إﻟﻰ ‪ 10‬ﺛواﻧﻰ ‪.‬‬ ‫‪ -‬أدﺧل اﻟرﻗم اﻟﺳرى ﺑﺎﺳﺗﺧدام )‪ (-‬أو )‪(+‬‬
‫‪ -‬أدﺧل اﻟرﻗم اﻟﺳرى ﺑﺎﺳﺗﺧدام )‪ (-‬أو )‪(+‬‬ ‫‪PRESS (+) KEY‬‬
‫‪ ON‬وﺳﺗظﮭر اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪:‬‬ ‫اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪-:‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر ﻟﻠﺣﻔظ‪.‬‬ ‫ﺛم اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻼﻧﺗﻘﺎل إﻟﻰ اﻟرﻗم‬
‫ﺛم اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻼﻧﺗﻘﺎل‬
‫‪MANUAL SERVICE‬‬ ‫‪ -‬ﻗم ﺑﺣﻔظ اﻻﺧﺗﯾﺎر ﻋن طرﯾﻖ اﻟﺿﻐط ﻋﻠﻰ‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﻼﺧﺗﯾﺎر‬ ‫وﻓﻲ ﺣﺎﻟﺔ ﻣﺎ ﯾﻛون اﻟﺑﺎب أﺗوﻣﺎﺗﯾك وﺑﺎﻟدﺧول ﻋﻠﻰ‬ ‫اﻟﺗﺎﻟﻲ ﻟﻠرﻗم اﻟﺳرى‪.‬‬
‫‪ENTER PASSWORD‬‬ ‫إﻟﻰ اﻟرﻗم اﻟﺗﺎﻟﻰ ﻟﻠرﻗم اﻟﺳرى‪.‬‬ ‫‪ENTER PASSWORD‬‬
‫‪1‬‬ ‫‪ON‬‬ ‫‪ ،ENTER‬ﺳﺗظﮭر اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪:‬‬ ‫ﺑﯾن ﺗﺷﻐﯾل ﺗﺳﺟﯾل اﻟدور ‪ ON‬أو إﻟﻐﺎء ﺗﺳﺟﯾل‬ ‫‪00000‬‬ ‫‪Cam Open: 3‬‬ ‫ھذه اﻟﺧطوة ﺳﺗظﮭر اﻟﺷﺎﺷﺔ اﻟﺗﺎﻟﯾﺔ ‪-:‬‬ ‫‪00000‬‬ ‫)‪.(00000‬‬ ‫ھو‬ ‫اﻟﻣﺻﻧﻊ‬ ‫ﺿﺑط‬ ‫ﻣﻠﺣوظﺔ‪ :‬رﻗم‬
‫ﻣﻠﺣوظﺔ‪ :‬رﻗم ﺿﺑط اﻟﻣﺻﻧﻊ ھو )‪.(00000‬‬
‫وھذا ﯾﻌﻧﻲ أن اﻟﻣﺻﻌد ﻓﻲ وﺿﻊ اﻟﺻﯾﺎﻧﺔ ﻋﻠﻰ‬ ‫اﻟدور ‪OFF‬‬ ‫وھو زﻣن ﻓﺗﺢ اﻟﺑﺎب اﻷﺗوﻣﺎﺗﯾك‬
‫‪F2 S4 SLOW : :‬‬ ‫‪Floor 0: EXTERNAL‬‬ ‫اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﺣدﯾد ھذا اﻟزﻣن‬
‫‪ERR: SERV 8‬‬ ‫اﻟﺳرﻋﺔ اﻟﺑطﯾﺋﺔ‪.‬‬ ‫‪ -‬ﻓﻰ ﺣﺎﻟﺔ اﺧﺗﯾﺎر ‪ OFF‬ﺳوف‬ ‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P1 (1‬ﺗﺤﺪﯾﺪ ﻋﺪد اﻷﺑﻮاب اﻟﻌﺎﻣﻠﺔ‬
‫‪1 ON‬‬ ‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P14 (14‬ﻋﺪد ﻣﺮات ﻣﺤﺎوﻻت اﻟﻜﺎﻣﺔ‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر ﻟﻠﺣﻔظ‬
‫‪ -‬ﻛﻣﺎ ﯾﻣﻛن ﻓﻲ ھذه اﻟﺣﺎﻟﺔ اﻻﺧﺗﯾﺎر ﺑﯾن ﺗﺣرﯾك‬ ‫ﯾظﮭر ﻟك ﺷﺎﺷﺔ إدﺧﺎل اﻟﻛود‪.‬‬
‫‪Floor 0: EXTERNAL‬‬ ‫ھو ﻟﺗﺣدﯾد ﻋدد اﻟﻣﺣﺎوﻻت اﻟﺗﻲ ﯾﻘوم ﺑﮭﺎ‬ ‫وﺑﻌد ذﻟك ﺳﺗظﮭر اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪-:‬‬ ‫‪P1>Floor Number‬‬ ‫ﯾُﺿﺑط ﻋدد اﻷﺑواب اﻟﻌﺎﻣﻠﺔ ﺣﺗﻰ‪ 16‬ﺑﺎﺑًﺎ )وﻗﻔﺔً(‪.‬‬
‫‪F2 S4 FAST : :‬‬ ‫اﻟﻣﺻﻌد ﺑﺎﻟﺳرﻋﺔ اﻟﺳرﯾﻌﺔ أو اﻟﺳرﻋﺔ اﻟﺑطﯾﺋﺔ‬ ‫ﻗم ﺑﺎﻟﺿﻐط ﻋﻠﻰ )‪ +‬ﻣﻊ –( ﻓﻰ‬ ‫‪P14> CAM TRIALS‬‬ ‫‪Cam Close: 3‬‬
‫‪0 OFF‬‬ ‫اﻟﻛﺎرت ﻟﻐﻠﻖ اﻟﻛﺎﻟون ﻋن طرﯾﻖ ﺷد اﻟﻛﺎﻣﺔ‬ ‫وھو زﻣن ﻏﻠﻖ اﻟﺑﺎب اﻷﺗوﻣﺎﺗﯾك اﺿﻐط ﻋﻠﻰ‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺳﺗظﮭر‬
‫‪ERR: SERV 8‬‬ ‫ﺑﺎﻟﺿﻐط ﻋﻠﻰ زر ‪ ENTER‬ﻛﻣﺎ ﺑﺎﻟﺷﺎﺷﺔ‪.‬‬ ‫ﻧﻔس اﻟوﻗت ﻟﺗﺄﻛﯾد اﻻﺧﺗﯾﺎر وذﻟك‬
‫‪Floor 0: EXTERNAL‬‬ ‫وﺑﻌدھﺎ ﯾﻘوم ﺑﺈﺳﻘﺎط ﻛﺎﻓﺔ اﻟطﻠﺑﺎت و إﯾﻘﺎف‬ ‫)‪ (+‬أو )‪ (-‬ﻟﺗﺣدﯾد ھذا اﻟزﻣن‬ ‫اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪-:‬‬
‫ﻟﺗﺄﻣﯾن ﻋدم اﻻﺧﺗﯾﺎر اﻟﺧﺎطﺊ‪.‬‬
‫‪Press Code...‬‬ ‫اﻟﻛﺎرت ﻋن اﻟﻌﻣل ﻟﻠﺣﻔﺎظ ﻋﻠﻰ اﻟﻛﺎﻣﺔ ﻣن اﻟﺗﻠف وﻓﻰ ﺣﺎﻟﺔ ﻋدم اﻟرﻏﺑﺔ‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر ﻟﻠﺣﻔظ‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﺣدﯾد ﻋدد اﻷدوار ﺛم‬
‫‪ -‬ﯾﻣﻛن اﺧﺗﯾﺎر اﺗﺟﺎه اﻟﺣرﻛﺔ ﻋن طرﯾﻖ اﻟﺿﻐط‬ ‫اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﺑرﻣﺟﺔ اﻟدور اﻟﺗﺎﻟﻲ‪.‬‬
‫ﻓﻰ ﺗﻔﻌﯾل ھذه اﻟﺧﺎﺻﯾﺔ ‪ ،‬ﯾﺗم اﺧﺗﯾﺎر اﻟرﻗم ﺻﻔر‪.‬‬ ‫‪Floor No.: 7‬‬ ‫اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر ﻟﻠﺣﻔظ‪.‬‬
‫ﻋﻠﻰ زر )‪ (+‬ﻟﻠﺣرﻛﺔ ﻓﻲ اﺗﺟﺎه اﻟﺻﻌود أو )‪(-‬‬ ‫‪ -‬ﻛرر اﻟﺧطوات اﻟﺳﺎﺑﻘﺔ ﺣﺗﻰ ﺗﻧﺗﮭﻲ ﻣن ﺟﻣﯾﻊ‬ ‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P9 (9‬أﻗﺼﻰ زﻣﻦ ﻟﻠﺴﺮﻋﺔ اﻟﺒﻄﯿﺌﺔ‬
‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺳﺗظﮭر اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪-:‬‬ ‫ﻣﺛﺎل‪:‬‬
‫ﻟﻠﺣرﻛﺔ ﻓﻲ اﺗﺟﺎه اﻟﻧزول‪.‬‬ ‫اﻷدوار‪.‬‬
‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﺣدﯾد ﻋدد اﻟﻣﺣﺎوﻻت‪.‬‬ ‫‪P9> SLOW TIME‬‬ ‫وھو أﻗﺻﻰ زﻣن ﻟﺗﺣرك اﻟﻛﺎﺑﯾﻧﺔ ﺑﺎﻟﺳرﻋﺔ‬ ‫ﻟﻌدد ‪ 8‬أدوار )وﻗﻔﺎت( أدﺧل اﻟرﻗم ‪7‬‬
‫‪ -‬وﻟﻠﺧروج ﻗم ﺑﺎﻟﺿﻐط ﻋﻠﻰ زر ‪.Reset‬‬ ‫ﻓﻲ اﻟﻧﮭﺎﯾﺔ اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠﺣﻔظ‪.‬‬ ‫‪Cam Trial: 0‬‬
‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر ﻟﻠﺣﻔظ‪.‬‬ ‫اﻟﺑطﯾﺋﺔ وﺑﻌد اﻧﺗﮭﺎﺋﮫ ﯾﺗم إﯾﻘﺎف اﻟﻛﺎﺑﯾﻧﺔ أﺗوﻣﺎﺗﯾﻛﯾﺎ‪.‬‬ ‫ﻟﻌدد ‪ 10‬أدوار )وﻗﻔﺎت( أدﺧل اﻟرﻗم ‪9‬‬
‫‪ -‬ﻗم ﺑﺑرﻣﺟﺔ اﻟطﻠﺑﺎت اﻟداﺧﻠﯾﺔ ‪INTERNAL‬‬
‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺳﺗظﮭر‬
‫ﺑﻧﻔس اﻟطرﯾﻘﺔ وﻓﻰ اﻟﻧﮭﺎﯾﺔ اﺿﻐط ﻋﻠﻰ‬ ‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P15 (15‬زﻣﻦ اﻟﺸﻮﻛﺔ‬ ‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ - : P2 (2‬ﺗﺤﺪﯾﺪ ﻧﻮع اﻟﻤﺒﯿﻦ‬
‫اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪-:‬‬
‫ﻣﻠﺤﻮﻇﺔ‪ :‬ﺟﻤﯿﻊ اﻷرﻗﺎم اﻟﻤﻮﺟﻮدة ﻋﻠﻰ اﻟﺸﺎﺷﺎت ھﻰ أرﻗﺎم ﺿﺒﻂ اﻟﻤﺼﻨﻊ‬ ‫‪ ENTER‬ﻟﻠﺣﻔظ‪.‬‬
‫ﺳﯾﺗم إﺳﻘﺎط ﻛﺎﻓﺔ اﻟطﻠﺑﺎت وﻏﻠﻖ ﻧور اﻟﻛﺎﺑﯾﻧﺔ‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﺣدﯾد اﻟزﻣن ﻣن ‪4‬‬ ‫‪P2> DISPLAY MODE‬‬ ‫ﻟﺗﺣدﯾد ﻧوع اﻟﻣﺑﯾن اﺿﻐط ﻋﻠﻰ ‪ENTER‬‬
‫‪P15> FORK TIME‬‬ ‫‪Slow Time: 8‬‬
‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P21 (21‬ﺑﺮﻣﺠﺔ أﻣﺎن ﺷﻮﻛﺔ اﻟﻜﺎﻟﻮن‬ ‫وذﻟك ﻓﻰ ﺣﺎﻟﺔ ﻓﺗﺢ اﻟﺷوﻛﺔ اﻟﺧﺎﺻﺔ ﺑﺎﻟﺑﺎب‬ ‫إﻟﻰ ‪ 25‬ﺛﺎﻧﯾﺔ‪.‬‬ ‫ﻟﻠدﺧول ﺛم اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻻﺧﺗﯾﺎر ﻧوع اﻟﻣﺑﯾن اﻟﻣطﻠوب‪.‬‬
‫وھذه اﻟﺧﺎﺻﯾﺔ ﺗﻘوم ﺑﺎﻟﺗﺄﻛد ﻣن‬ ‫اﻟﺧﺎرﺟﻰ طوال ھذا اﻟزﻣن‪.‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر ﻟﻠﺣﻔظ‪.‬‬
‫‪P21> LOCK ERROR‬‬
‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺳﺗظﮭر‬ ‫‪Display:‬‬ ‫‪Display:‬‬
‫ﺳﻼﻣﺔ أﻣﺎن اﻟﻛﺎﻟون ﻋﻧد ﺗﺷﻐﯾﻠﮭﺎ‪.‬‬ ‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P10 (10‬أﻗﺼﻰ زﻣﻦ ﻟﻠﺴﺮﻋﺔ اﻟﺴﺮﯾﻌﺔ‬ ‫‪7SEGMENT‬‬ ‫‪Floor Wire‬‬
‫ﺑﻣﻌﻧﻰ أﻧﮫ ﻻ ﺑد ﻣن ﻓﺗﺢ أﻣﺎن ﺷوﻛﺔ اﻟﻛﺎﻟون ﻋﻧد ﻛل ﺗوﻗف ﻟﻠﻛﺎﺑﯾﻧﺔ ﻋﻠﻰ‬ ‫‪Fork Time: 4‬‬
‫اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪-:‬‬
‫‪1 ON‬‬ ‫ﻣن‬ ‫اﻟزﻣن‬ ‫ﻟﺗﺣدﯾد‬ ‫)‪(-‬‬ ‫أو‬ ‫)‪(+‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ‬ ‫‪P10> FAST TIME‬‬ ‫وھو أﻗﺻﻰ زﻣن ﻟﺗﺣرك اﻟﻛﺎﺑﯾﻧﺔ ﺑﺎﻟﺳرﻋﺔ‬ ‫اﻟﻣﺑﯾـن اﻟﺳﺑـﺎﻋـﻲ‬ ‫ﻓـردة ﻛـل دور‬
‫اﻟدور‪ ،‬وﻓﻲ ﺣﺎﻟﺔ ﻋدم ﻓﺗﺢ أﻣﺎن اﻟﻛﺎﻟون ﻟن ﺗﺗﺣرك اﻟﻛﺎﺑﯾﻧﺔ وذﻟك ﻟﺗﺄﻣﯾن‬
‫دﻗﯾﻘﺔ إﻟﻰ ‪ 4‬دﻗﺎﺋﻖ‪.‬‬ ‫اﻟﺳرﯾﻌﺔ وﺑﻌد اﻧﺗﮭﺎﺋﮫ ﯾﺗم إﯾﻘﺎف اﻟﻛﺎﺑﯾﻧﺔ‪.‬‬
‫ﻋدم إﻟﻐﺎء أﻣﺎن اﻟﻛﺎﻟون أو ﻓﻲ ﺣﺎﻟﺔ ﻋطل رﯾﻼي اﻟﻛﺎﻟون داﺧل ﻟوﺣﺔ‬ ‫‪Display:‬‬ ‫‪Display:‬‬
‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر ﻟﻠﺣﻔظ‪.‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺳﺗظﮭراﻟﺷﺎﺷﺔ‬
‫اﻟﻛﻧﺗرول ‪.‬‬ ‫‪Binary NEG‬‬ ‫‪Binary POS‬‬
‫اﻵﺗﯾﺔ‪-:‬‬
‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺳﺗظﮭر اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪-:‬‬ ‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P16 (16‬زﻣﻦ ودور اﻟﺘﺠﺮﯾﺶ‬ ‫‪Fast Time: 15‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﺣدﯾد اﻟزﻣن ﻣن ‪10‬‬ ‫ﻣﺒﯿﻦ ﺛﻨﺎﺋﻲ ذو ﻃﺮف إﺷﺎرة ﺳﺎﻟﺐ‬ ‫ﻣﺒﯿﻦ ﺛﻨﺎﺋﻲ ذو ﻃﺮف إﺷﺎرة ﻣﻮﺟﺐ‬
‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﻼﺧﺗﯾﺎر ﺑﯾن إﻟﻐﺎء أﻣﺎن ﺷوﻛﺔ اﻟﻛﺎﻟون ‪OFF‬‬
‫وھو اﻟزﻣن اﻟذي ﯾﺗم ﺗﺣرﯾك اﻟﻛﺎﺑﯾﻧﺔ ﺑﻌد‬ ‫إﻟﻰ ‪ 90‬ﺛﺎﻧﯾﺔ‪.‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر ﻟﻠﺣﻔظ‪.‬‬
‫أو ﺗﺷﻐﯾل أﻣﺎن ﺷوﻛﺔ اﻟﻛﺎﻟون ‪. ON‬‬ ‫‪P16> PARK TIME‬‬
‫اﻧﺗﮭﺎﺋﮫ إﻟﻰ اﻟدور اﻟﻣﺣدد ﻟﻠﺟراج ﻓﻲ ﺣﺎﻟﺔ‬ ‫‪ -‬ﺑﺎﻟﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺳﺗدﺧل ﻋﻠﻰ ﺧطوة‬ ‫ﻋﻧد اﺧﺗﯾﺎر اﻟﻣﺑﯾـن اﻟﺳﺑـﺎﻋـﻲ ‪ 7-segment‬أو اﻟﺛﻧﺎﺋﻲ ﺑﻧوﻋﯾﮫ‪ ،‬ﺑﻌد‬
‫‪LOCK ERROR:‬‬ ‫‪LOCK ERROR:‬‬ ‫‪ Supervisor‬ﻟﺗﺣدﯾد ﻛﯾﻔﯾﺔ اﻟرﺟوع إﻟﻰ‬
‫ﻋدم اﺳﺗﺧدام اﻟﻣﺻﻌد‪.‬‬ ‫‪Floor 0: 0‬‬ ‫اﻟﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺳﺗظﮭر اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪-:‬‬
‫‪0 OFF‬‬ ‫‪1 ON‬‬ ‫اﻟوﺿﻊ اﻟطﺑﯾﻌﻲ ﻟﻠﻌﻣل ﻓﻲ ﺣﺎﻟﮫ ﺣدوث أﻗﺻﻰ‬
‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺳﺗظﮭر‬ ‫ﯾﻼﺣظ إﻣﻛﺎﻧﯾﺔ ﻛﺗﺎﺑﺔ رﻗم اﻟدور ﻋﻠﻰ رﻗﻣﯾن‪ ،‬اﻟرﻗم اﻷول ﻋﻠﻰ اﻟﯾﺳﺎر إﻣﺎ‬
‫‪Supervisor‬‬ ‫زﻣن ﻟﻠﺳرﻋﺔ اﻟﺳرﯾﻌﺔ‪.‬‬
‫وﻓﻰ ﺣﺎﻟﺔ اﺧﺗﯾﺎر اﻟوﺿﻊ ‪ ON‬ﺳﺗظﮭر‬ ‫اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪-:‬‬ ‫‪0 OFF‬‬ ‫) ‪ 1‬أو ﻻ ﯾوﺟد رﻗم( أﻣﺎ اﻟرﻗم اﻟﺛﺎﻧﻲ ﻋﻠﻰ اﻟﯾﻣﯾن ﻓﯾﻣﻛن ﺗﻐﯾﯾره ﻷرﻗﺎم أو‬
‫ﻟك ﺷﺎﺷﺔ إدﺧﺎل اﻟﻛود‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﻐﯾﯾر اﻟزﻣن‪.‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻻﺧﺗﯾﺎر اﻟوﺿﻊ‬
‫‪LOCK ERROR:‬‬ ‫ﺣروف أو ﻋﻼﻣﺎت ﺣﺳب اﻟﻣﺗﺎح ﺑﺎﻟﺑرﻧﺎﻣﺞ‪.‬‬
‫‪Press Code...‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ) ‪ +‬ﻣﻊ – ( ﻓﻰ ﻧﻔس‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر‬ ‫‪ ON‬أو ‪.OFF‬‬
‫‪Park time: XX‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﻐﯾﯾر اﻟرﻗم اﻷول‪.‬‬
‫اﻟوﻗت ﻟﺗﺄﻛﯾد اﻻﺧﺗﯾﺎر وذﻟك ﻟﺗﺄﻣﯾن‬ ‫ﻟﻠﺣﻔظ‪..‬‬ ‫ﻓﻲ ﺣﺎﻟﺔ اﺧﺗﯾﺎرك ‪، OFF‬ﺗﻠﻐﻰ ھذه اﻟﺧﺎﺻﯾﺔ‬
‫‪0 OFF‬‬ ‫‪ -‬اﺿﻐط ‪ ENTER‬ﻹﻋداد اﻟرﻗم اﻟﺛﺎﻧﻲ‪.‬‬
‫ﻋدم اﻻﺧﺗﯾﺎر اﻟﺧﺎطﺊ‪.‬‬ ‫ﻣﻠﺣوظﺔ‪ :‬ﯾﺗم ﺗﺣدﯾد زﻣن اﻟﺗﺟرﯾش ﻣن دﻗﯾﻘﺔ‬ ‫وﯾﺗم إﻋﺎدة اﻟﻛﺎرت ﻟوﺿﻊ اﻟﺗﺷﻐﯾل اﻟطﺑﯾﻌﻲ ﻋﻧد‬
‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﻐﯾﯾر اﻟرﻗم اﻟﺛﺎﻧﻲ‪.‬‬
‫‪Park Time: 29‬‬ ‫إﻟﻰ ‪ 29‬دﻗﯾﻘﺔ أﻣﺎ ﻓﻲ ﺣﺎﻟﺔ اﻟﺿﻐط ﻋﻠﻰ )‪(+‬‬ ‫‪Supervisor‬‬ ‫اﻟﺿﻐط ﻋﻠﻰ زر ‪ reset‬أو ﻓﺻل اﻟﻛﮭرﺑﺎء‬
‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -:P22 (22‬ﺑﺮﻧﺎﻣﺞ أﻗﺼﻰ ﻋﺪد ﻟﻠﻄﻠﺒﺎت اﻟﺪاﺧﻠﯿﺔ‬ ‫‪ -‬ﻋﻧد اﻻﻧﺗﮭﺎء اﺿﻐط ﻋﻠﻰ ‪ ، ENTER‬ﺳوف ﺗظﮭر ﻛﻠﻣﺔ ?‪.Store‬‬
‫‪1 ON‬‬ ‫ﻟﻌدد أﻛﺑر ﻣن )‪ 29‬دﻗﯾﻘﺔ( ﯾﻠﻐﻰ اﻟﺟراج‬ ‫‪1 ON‬‬ ‫وإﻋﺎدﺗﮭﺎ ‪.‬‬
‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻣرة أﺧرى ﻟﺣﻔظ اﻟرﻗم أو )‪ (+‬أو )‪ (-‬ﻓﻰ ﺣﺎﻟﺔ‬
‫‪P22> MAX CALLS‬‬ ‫وھذه اﻟﺧﺎﺻﯾﺔ ﺗﻘوم ﺑﺗﺄﻣﯾن اﻟﻣﺻﻌد‬ ‫ﻓﻲ ﺣﺎﻟﺔ اﺳﺗﺧدام زﻣن ﻟﻠﺟراج ﺳﺗظﮭر ﺷﺎﺷﺔ‬ ‫‪ -‬ﻓﻲ ﺣﺎﻟﺔ اﺧﺗﯾﺎرك ‪ON‬‬
‫‪Park Floor: 0‬‬ ‫اﻟرﻏﺑﺔ ﻓﻰ إﻋﺎدة اﻟﺿﺑط ﻟﻧﻔس اﻟدور‪.‬‬
‫ﻣن ﻋﺑث اﻷطﻔﺎل ﺑﺣﯾث ﻻ ﯾﺗم ﻗﺑول ﺗﺳﺟﯾل ﻋدد طﻠﺑﺎت داﺧﻠﯾﺔ أﻛﺛر ﻣن‬ ‫إدﺧﺎل اﻟدور اﻟﻣطﻠوب ﻟﻠﺟراج‬ ‫‪،‬ﺗﻔﻌل ھذه اﻟﺧﺎﺻﯾﺔ وﯾﺗم إﻋﺎدة اﻟﻛﺎرت ﻟوﺿﻊ‬
‫‪ -‬ﻛرر اﻟﺧطوات اﻟﺳﺎﺑﻘﺔ ﺣﺗﻰ ﯾﺗم اﻻﻧﺗﮭﺎء ﻣن ﻛل اﻷدوار‬
‫اﻟﻌدد اﻟذى ﺗم ﺑرﻣﺟﺗﮫ اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺳﺗظﮭر اﻟﺷﺎﺷﺔ‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﺣدﯾد دور‬ ‫اﻟﺗﺷﻐﯾل اﻟطﺑﯾﻌﻲ ﻋﻧد اﻟدﺧول ﻓﻲ وﺿﻊ اﻟﺻﯾﺎﻧﺔ‬
‫اﻟﺟراج‪.‬‬ ‫ﺛم اﻟﺧروج ﻣﻧﮫ‪.‬‬ ‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P3 (3‬اﻟﻤﺒﯿﻦ اﻟﺴﺮﯾﺎل ) اﻟﺠﺮاى (‬
‫اﻵﺗﯾﺔ‪-:‬‬
‫‪MAX CALLS:‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر ﻟﻠﺣﻔظ‪.‬‬ ‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P11 (11‬زﻣﻦ إﺿﺎءة اﻟﻜﺎﺑﯿﻨﺔ‬ ‫‪P3> LED MATRIX‬‬
‫‪(OFF) -‬إﻟﻐﺎء ھذه اﻟﺧﺎﺻﯾﺔ ‪.‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول‪.‬‬
‫‪OFF‬‬
‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P17 (17‬زﻣﻦ اﻟﺼﯿﺎﻧﺔ اﻹﺟﺒﺎري‬ ‫وھو زﻣن اﻹﺿﺎءة اﻟذي ﺑﻌد اﻧﺗﮭﺎﺋﮫ‬ ‫‪ -‬ﯾﻣﻛن ﺗﻐﯾﯾر اﻷرﻗﺎم )اﻷول واﻟﺛﺎﻧﻲ( إﻟﻰ أرﻗﺎم أو ﺣروف أو ﻋﻼﻣﺎت‪.‬‬
‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻻﺧﺗﯾﺎر أﻗﺻﻰ ﻋدد ﻟﺗﺳﺟﯾل اﻟطﻠﺑﺎت‬ ‫‪P11> LAMP TIME‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﻐﯾﯾر اﻟرﻗم اﻷول‪.‬‬
‫ﺗﻧطﻔﻰء إﻧﺎرة اﻟﻛﺎﺑﯾﻧﺔ ﻓﻲ ﺣﺎﻟﺔ ﺳﻛون‬
‫)‪ 4‬أو ‪ 6‬أو ‪( 8‬‬ ‫‪P17> OPER.TIMEOUT‬‬
‫ھو اﻟزﻣن اﻟذي ﺑﻌد اﻧﺗﮭﺎﺋﮫ ﺳوف‬ ‫اﻟﻣﺻﻌد‪.‬‬ ‫‪ -‬اﺿﻐط ‪ ENTER‬ﻹﻋداد اﻟرﻗم اﻟﺛﺎﻧﻲ‪.‬‬
‫‪MAX CALLS‬‬ ‫‪ -‬اﺿﻐط ‪ ENTER‬ﺳﺗظﮭر ﺷﺎﺷﺔ إدﺧﺎل اﻟﻛود‪.‬‬ ‫ﯾﺗوﻗف اﻟﻛﺎرت ﻋن اﻟﻌﻣل‪.‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺳﺗظﮭر اﻟﺷﺎﺷﺔ‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﻐﯾﯾر اﻟرﻗم اﻟﺛﺎﻧﻲ‪.‬‬
‫‪4 CALLS‬‬ ‫‪ -‬ﻗم ﺑﺎﻟﺿﻐط ﻋﻠﻰ )‪ +‬ﻣﻊ –( ﻓﻰ ﻧﻔس‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺳﺗظﮭر‬ ‫‪ -‬ﻋﻧد اﻻﻧﺗﮭﺎء اﺿﻐط ﻋﻠﻰ ‪ ، ENTER‬ﺳوف ﺗظﮭر ﻛﻠﻣﺔ ?‪.Store‬‬
‫اﻵﺗﯾﺔ‪-:‬‬
‫‪MAX CALLS‬‬ ‫اﻟوﻗت ﻟﺗﺄﻛﯾد اﻻﺧﺗﯾﺎر وذﻟك ﻟﺗﺄﻣﯾن‬ ‫اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪-:‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ) ‪ +‬أو ‪ ( -‬ﻟﺗﺣدﯾد اﻟزﻣن ﻣن ‪1‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻣرة أﺧرى ﻟﺣﻔظ اﻟرﻗم أو )‪ (+‬أو )‪ (-‬ﻓﻰ ﺣﺎﻟﺔ‬
‫ﻋدم اﻻﺧﺗﯾﺎر اﻟﺧﺎطﺊ‪.‬‬ ‫‪Oper . Timeout:‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ)‪ (+‬أو)‪ (-‬ﻟﻼﺧﺗﯾﺎر‪.‬‬ ‫‪Lamp Time: 8‬‬ ‫اﻟرﻏﺑﺔ ﻓﻰ إﻋﺎدة اﻟﺿﺑط ﻟﻧﻔس اﻟدور‪.‬‬
‫…‪Press Code‬‬ ‫إﻟﻰ ‪ 90‬ﺛﺎﻧﯾﺔ‪.‬‬
‫‪0 OFF‬‬ ‫‪ -‬ﻛرر اﻟﺧطوات اﻟﺳﺎﺑﻘﺔ ﺣﺗﻰ ﯾﺗم اﻻﻧﺗﮭﺎء ﻣن ﻛل اﻷدوار‪.‬‬
‫وﯾﻣﻛﻧك ﻓﻲ ھذا اﻟﺑرﻧﺎﻣﺞ‪:‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر ﻟﻠﺣﻔظ‬
‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P23 (23‬ﺑﺮﻧﺎﻣﺞ اﻟﺤﺮﯾﻖ‬ ‫‪Oper . Timeout:‬‬ ‫‪ -‬اﺧﺗﯾﺎر ‪OFF‬ﻹﯾﻘﺎف ﻋداد اﻟزﻣن‪ ،‬ﻓﯾﻌﻣل‬ ‫‪Floor 0: 0‬‬
‫‪1 ON‬‬ ‫اﻟﻛﺎرت ﺑدون ﺗوﻗف إطﻼﻗﺎ‪.‬‬ ‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P12 (12‬اﻟﻄﻮارئ‬
‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺳﺗظﮭر‬ ‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P4 (4‬اﺧﺘﯿﺎر ﻧﻮع اﻟﺒﺎب‬
‫‪P23> FIREMAN‬‬ ‫‪Oper . Timeout:‬‬ ‫‪ -‬اﺧﺗﯾﺎر ‪ ON‬ﻟﺗﺷﻐﯾل ﻋداد اﻟزﻣن‪.‬‬ ‫‪P12> EMERGENCY‬‬ ‫ﯾﺗم اﻻﺧﺗﯾﺎر ﺑﯾن إﯾﻘﺎف أو ﺗﺷﻐﯾل ﺧﺎﺻﯾﺔ‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺛم اﺿﻐط‬
‫اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪-:‬‬ ‫‪2 Restart‬‬ ‫‪ -‬اﺧﺗﯾﺎر ‪ Restart‬ﻟﺗﺻﻔﯾر ﻋداد اﺣﺗﺳﺎب‬ ‫‪P4> DOOR TYPE‬‬
‫اﻟطوارئ ﺑﺎﻟﻛﺎرت ‪.‬‬ ‫ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻻﺧﺗﯾﺎر ﻧوع اﻟﺑﺎب‪:‬‬
‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﻼﺧﺗﯾﺎر ﺑﯾن‬ ‫اﻟزﻣن وﻏﻠﻖ اﻟﻌداد‪.‬‬
‫‪Fireman‬‬ ‫اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺳﺗظﮭر‬
‫‪0 OFF‬‬ ‫ﺗﺷﻐﯾل ﻧﻘطﺔ إﻧذار اﻟﺣرﯾﻖ ‪ON‬أو‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر ﻟﻠﺣﻔظ‪.‬‬ ‫اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪-:‬‬ ‫‪Door: Manual‬‬
‫إﻟﻐﺎﺋﮭﺎ ‪. OFF‬‬ ‫‪Period: 1 month‬‬ ‫‪ -‬ﻓﻰ ﺣﺎﻟﺔ اﺧﺗﯾﺎر اﻟوﺿﻊ ‪ ON‬ﺛم اﻟﺿﻐط ﻋﻠﻰ‬
‫‪Fireman‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﻼﺧﺗﯾﺎر‬ ‫ﻋــﺎدى‬
‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر ﻟﻠﺣﻔظ‪.‬‬ ‫‪ ENTER‬ﺳﺗظﮭر ﺷﺎﺷﺔ ﺗﺣدﯾد اﻟﻣدة ﻣن ﺷﮭر‬
‫‪1 ON‬‬ ‫‪Emergency:‬‬ ‫ﺑﯾن ﺗﺷﻐﯾل اﻟﺧﺎﺻﯾﺔ ﻋﻠﻰ وﺿﻊ ‪ON‬‬ ‫‪Door: Wait- Close‬‬ ‫‪Door: Wait- Open‬‬
‫‪ -‬ﻓﻰ ﺣﺎﻟﺔ اﺧﺗﯾﺎر ‪ ON‬ﺳﺗظﮭر ﺷﺎﺷﺔ إدﺧﺎل‬ ‫إﻟﻰ ‪ 6‬أﺷﮭر‬ ‫‪1‬‬ ‫‪ON‬‬ ‫أو إﻟﻐﺎﺋﮭﺎ ﻋﻠﻰ وﺿﻊ ‪OFF‬‬ ‫أﺗﻮﻣﺎﺗﯿﻚ ﻣﻘﻔﻮل‬ ‫أﺗﻮﻣﺎﺗﯿﻚ ﻣﻔﺘﻮح‬
‫اﻟﻛود‪.‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر ﻟﻠﺣﻔظ‪.‬‬
‫‪Fireman‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠﺣﻔظ‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر ﻟﻠﺣﻔظ‪.‬‬
‫‪ -‬ﻗم ﺑﺎﻟﺿﻐط ﻋﻠﻰ )‪ +‬ﻣﻊ –( ﻓﻰ ﻧﻔس‬ ‫‪Emergency:‬‬
‫… ‪Press Code‬‬ ‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P18 (18‬إدﺧﺎل رﻗﻢ ﺗﻠﯿﻔﻮن ﻣﺮﻛﺰ اﻟﺼﯿﺎﻧﺔ‬ ‫‪0 OFF‬‬ ‫‪ -‬ﻋﻧد اﺧﺗﯾﺎر اﻟوﺿﻊ‪ ON‬اﺿﻐط ‪ENTER‬‬
‫اﻟوﻗت ﻟﺗﺄﻛﯾد اﻻﺧﺗﯾﺎر وذﻟك ﻟﺗﺄﻣﯾن ﻋدم اﻻﺧﺗﯾﺎر‬
‫ﯾﻣﻛﻧك ﻣن ﺧﻼل ھذا اﻟﺑرﻧﺎﻣﺞ ﺗﺧزﯾن رﻗم‬ ‫ﻟﺗﺣدﯾد اﻟزﻣن اﻟذي ﯾﻧﺗظره اﻟﻛﺎرت ﺑﻌد اﻧﻘطﺎع‬
‫اﻟﺧﺎطﺊ‪.‬‬ ‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P5 (5‬اﺧﺘﯿﺎر ﻧﻈﺎم ﺗﺸﻐﯿﻞ اﻟﻤﺼﻌﺪ‬
‫اﻟﺗﻠﯾﻔون اﻟﻣراد اﻻﺗﺻﺎل ﺑﮫ ﻋﻧد اﻧﺗﮭﺎء اﻟزﻣن ‪P18> SERVICE TEL.‬‬ ‫اﻟﺗﯾﺎر واﻟﺑدء ﻓﻲ ﺗﺑدﯾل وﺿﻊ ﺗﻐذﯾﺔ اﻻﻧﻔرﺗر‬
‫‪ -‬ﺳﺗظﮭر ﺷﺎﺷﺔ ﺿﺑط رﻗم اﻟدور اﻟﻣراد ﺗوﺟﮫ‬ ‫‪-‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺛم اﺿﻐط‬
‫اﻟﻣﺣدد ﻟﻠﺻﯾﺎﻧﺔ اﻹﺟﺑﺎرﯾﺔ‪.‬‬ ‫)أو ﺗﺷﻐﯾل رﯾﻼي ‪. (RN‬‬ ‫‪P5> SYSTEM TYPE‬‬
‫‪FireFLoor : 0‬‬ ‫اﻟﻛﺎﺑﯾﻧﺔ ﻧﺣوه ﻋﻧد ﺣدوث ﺣرﯾﻖ‪.‬‬ ‫ﻋﻠﻰ )‪ (+‬أو )‪(-‬ﻻﺧﺗﯾﺎر ﻧظﺎم اﻟﺗﺷﻐﯾل‪:‬‬
‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺳﺗظﮭر‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﺣدﯾد اﻟزﻣن ﻣن‬
‫‪ -‬اﺧﺗر رﻗم اﻟدورﻋن طرﯾﻖ اﻟﺿﻐط ﻋﻠﻰ )‪(+‬‬
‫اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪-:‬‬ ‫‪ 4‬إﻟﻰ ‪ 50‬ﺛﺎﻧﯾﺔ‪.‬‬
‫أو )‪ (-‬ﺛم اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر‬ ‫‪System: 2 Speed‬‬ ‫‪System: 3 Speed‬‬
‫ﻟﻠﺣﻔظ‪.‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﻐﯾﯾر اﻟرﻗم‬ ‫‪EMR Time: 4‬‬ ‫‪ -‬اﺿﻐط ‪ ENTER‬ﺳﺗظﮭراﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪:‬‬
‫‪SERVICE TEL.‬‬ ‫ﻣوﺗور ﺳرﻋﺗﯾن‬ ‫ﻣوﺗور ‪ 3‬ﺳرﻋﺎت‬
‫‪00000000000‬‬ ‫اﻷول‪ ،‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠﺣﻔظ‬ ‫وھو اﻟزﻣن ﻣﺎ ﺑﯾن ﺗﺷﻐﯾل رﯾﻼي ‪ RN‬واﻟﺑدء‬
‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P24 (24‬إﻋﺎدة ﺿﺒﻂ اﻟﻤﺼﻨﻊ‬
‫واﻻﻧﺗﻘﺎل إﻟﻰ اﻟرﻗم اﻟﺛﺎﻧﻲ ‪.‬‬ ‫ﻓﻲ ﺗﺷﻐﯾل إﺷﺎرة اﻟطوارئ‪.‬‬
‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺳﺗظﮭر‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر ﻟﻠﺣﻔظ‪.‬‬
‫‪P24> FACTORY SET‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﻐﯾﯾر اﻟرﻗم اﻟﺛﺎﻧﻲ‪.‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﺣدﯾد اﻟزﻣن ﻣن‬
‫اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪-:‬‬ ‫‪ 1‬إﻟﻰ ‪ 20‬ﺛﺎﻧﯾﺔ‪.‬‬ ‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P6 (6‬اﺧﺘﯿﺎر ﻧﻮع اﻟﺘﺠﻤﯿﻊ‬
‫…‪Press Code‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠﺣﻔظ واﻻﻧﺗﻘﺎل إﻟﻰ اﻟرﻗم اﻟﺛﺎﻟث‪.‬‬
‫ﻗم ﺑﺎﻟﺿﻐط ﻋﻠﻰ )‪ +‬ﻣﻊ –( ﻓﻰ ﻧﻔس اﻟوﻗت‬ ‫‪ -‬ﻛرر اﻟﺧطوات اﻟﺳﺎﺑﻘﺔ ﺣﺗﻰ ﺗﻧﺗﮭﻲ ﻣن إدﺧﺎل اﻟرﻗم ﺑﺎﻟﻛﺎﻣل‪.‬‬ ‫‪P6> COLLECTIVE‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺛم‬
‫‪ -‬اﺿﻐط ‪ ENTER‬ﺳﺗظﮭراﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪:‬‬
‫ﻟﺗﺄﻛﯾد اﻻﺧﺗﯾﺎر وذﻟك ﻟﺗﺄﻣﯾن ﻋدم اﻻﺧﺗﯾﺎر‬ ‫ﻓﻲ اﻟﻧﮭﺎﯾﺔ اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠﺣﻔظ‪.‬‬ ‫‪RN‬‬ ‫‪EMR: 5 sec‬‬ ‫اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻻﺧﺗﯾﺎر ﻧوع اﻟﺗﺟﻣﯾﻊ‪:‬‬
‫وھو اﻟزﻣن ﻣﺎ ﺑﯾن دﺧول إﺷﺎرة اﻟطوارئ‬
‫‪Press Code...‬‬ ‫اﻟﺧﺎطﺊ ﺳﺗظﮭر اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪.‬‬
‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P19 (19‬ﺗﻐﯿﯿﺮ اﻟﺮﻗﻢ اﻟﺴﺮي‬ ‫واﻟﺑدء ﻓﻲ ﺗﺷﻐﯾل إﺷﺎرة اﻻﺗﺟﺎه‪.‬‬ ‫‪Collective:‬‬ ‫‪Collective:‬‬ ‫‪Collective:‬‬
‫‪FACTORY SET OK‬‬ ‫‪EMR‬‬ ‫‪UP: 2 sec‬‬
‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﺣدﯾد اﻟزﻣن ﻣن‬ ‫‪Semi coll.‬‬ ‫‪Down coll.‬‬ ‫‪APB coll‬‬
‫ﯾﺳﺗﺧدم ھذا اﻟﺑرﻧﺎﻣﺞ ﻟﺗﻐﯾﯾر اﻟرﻗم اﻟﺳري‬ ‫‪ 0‬إﻟﻰ ‪ 20‬ﺛﺎﻧﯾﺔ‪.‬‬
‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P25 (25‬ﺗﺼﺤﯿﺢ ﻋﺪاد اﻟﺴﯿﻠﯿﻜﺘﻮر‬ ‫ﻟﻠدﺧول ﻋﻠﻰ اﻟﺑرﻧﺎﻣﺞ‪.‬‬ ‫ﺗﺠﻤﯿﻊ ﻛﻠﻰ‬ ‫ﺗﺠﻤﯿﻊ ﻧﺰول‬ ‫ﻃﻠﺐ واﺣﺪ‬
‫‪P19> SET PASSWORD‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر ﻟﻠﺣﻔظ‪.‬‬
‫‪P25> RESTORE SEL.‬‬‫وھﻲ ﺧﺎﺻﯾﺔ ﻟﺗﺻﺣﯾﺢ ﻋداد اﻟﺳﯾﻠﻛﺗور‬ ‫اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر ﻟﻠﺣﻔظ‪.‬‬
‫ﺑﺎﻟﻧزول إﻟﻰ اﻟدور اﻷرﺿﻲ وذﻟك ﻋﻧد‬ ‫ﺳﺗظﮭر اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪-:‬‬ ‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P13 (13‬ﻛﻮد ﺗﺸﻐﯿﻞ اﻟﻄﻠﺒﺎت اﻟﺪاﺧﻠﯿﺔ‬
‫اﻧﻘطﺎع اﻟﺗﯾﺎر اﻟﻛﮭرﺑﻲ وﻋودﺗﮫ ﻣرة‬ ‫‪ -‬ﻟﺗﻐﯾﯾراﻟرﻗم اﻟﺳرى ﻟﻠﺑرﻣﺟﺔ اﻷﺳﺎﺳﯾﺔ‬ ‫اﻟﺒﺮﻧﺎﻣﺞ رﻗﻢ )‪ -: P7 (7‬زﻣﻦ اﻟﺘﻮﻗﻒ ﻋﻠﻰ اﻟﺪور‬
‫‪P13> KeyCode‬‬ ‫ﯾﺗم اﻻﺧﺗﯾﺎر ﺑﯾن ﺗﺷﻐﯾل أو إﻟﻐﺎء ﺧﺎﺻﯾﺔ اﻟﻛود‬
‫اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﻐﯾﯾر اﻟرﻗم اﻷول ‪BASIC PASSWORD‬‬ ‫وھو اﻟزﻣن اﻟذي ﺗﻧﺗظره اﻟﻛﺎﺑﯾﻧﺔ ﺑﻌد ﺗﻣﺎم اﻟوﻗوف‬
‫أﺧرى‪.‬‬ ‫اﻟﺳرى وھو اﻟﺑدﯾل اﻷﻣﺛل ﻟﻣﻔﺗﺎح اﻟﻛﺎﺑﯾﻧﺔ أو‬ ‫‪P7> WAIT TIME‬‬
‫<<‪>>00000‬‬ ‫ﺛم اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠﺣﻔظ واﻻﻧﺗﻘﺎل‬
‫ﻟﻠدﺧول‬ ‫‪ENTER‬‬ ‫اﻟـ‬ ‫ﻋﻠﻰ‬ ‫ﻧﺿﻐط‬ ‫‪-‬‬ ‫اﻟﻛروت اﻟﻣﻛودة‪.‬‬ ‫ﻋﻠﻰ اﻟدور وﻗﺑل اﻟﺗﺣرك ﻣرة أﺧرى‪.‬‬
‫‪RESTORE SELECTOR‬‬
‫‪OFF‬‬ ‫‪0‬‬ ‫ﺳﺗظﮭر اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪-:‬‬ ‫إﻟﻰ اﻟرﻗم اﻟﺛﺎﻧﻲ‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺳﺗظﮭر‬
‫‪ -‬ﻋن طرﯾﻖ اﻟﺿﻐط ﻋﻠﻰ )‪ (+‬أو‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﻐﯾﯾر اﻟرﻗم اﻟﺛﺎﻧﻲ‬ ‫‪Wait time: 4‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠدﺧول ﺳﺗظﮭر اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪-:‬‬
‫اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪-:‬‬
‫)‪ (-‬ﻧﻘوم ﺑﺗﻔﻌﯾل ھذه اﻟﺧﺎﺻﯾﺔ وﺟﻌﻠﮭﺎ‬ ‫‪ADVANCED PASSWORD‬‬ ‫ﺛم اﺿﻐط ﻋﻠﻰ ‪ENTER‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﻼﺧﺗﯾﺎر ﺑﯾن ﺗﺷﻐﯾل‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﺣدﯾد اﻟزﻣن ﻣن ‪ 2‬إﻟﻰ ‪ 30‬ﺛﺎﻧﯾﺔ‪.‬‬
‫‪RESTORE SELECTOR‬‬ ‫<<‪>>00000‬‬ ‫ﻟﻠﺣﻔظ واﻻﻧﺗﻘﺎل إﻟﻰ اﻟرﻗم اﻟﺛﺎﻟث‬
‫‪ON‬‬ ‫‪1‬‬
‫‪ ON‬أو إﻟﻐﺎﺋﮭﺎ وﺟﻌﻠﮭﺎ ‪OFF‬‬ ‫‪KeyCode‬‬ ‫‪ ON‬أو إﻟﻐﺎء ‪.OFF‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر ﻟﻠﺣﻔظ‪.‬‬
‫ﺛم ﻧﺿﻐط ﻋﻠﻰ اﻟـ ‪ ENTER‬ﺑﻌد‬ ‫‪ -‬ﻛرر اﻟﺧطوات اﻟﺳﺎﺑﻘﺔ ﺣﺗﻰ ﺗﻧﺗﮭﻲ ﻣن إدﺧﺎل اﻟرﻗم ﺑﺎﻟﻛﺎﻣل ﺣﺗﻲ ﺗظﮭر‬ ‫‪0 OFF‬‬ ‫‪ -‬ﻋﻧد اﺧﺗﯾﺎر اﻟوﺿﻊ ‪ ON‬اﺿﻐط ‪Enter‬‬
‫‪www.ultimatrue.com‬‬ ‫ﻛﻠﻣﺔ ‪ Store‬ﻓﻰ اﻟﻧﮭﺎﯾﺔ اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﻟﻠﺣﻔظ‬
‫اﻻﺧﺗﯾﺎر ﻟﻠﺣﻔظ‪.‬‬ ‫‪KeyCode‬‬ ‫ﺳﺗظﮭر اﻟﺷﺎﺷﺔ اﻵﺗﯾﺔ‪:‬‬
‫‪[email protected]‬‬ ‫‪ -‬اﺿﻐط ‪ Enter‬ﻟﺗﻐﯾﯾر اﻟرﻗم اﻟﺳري ﻟﻠﺑرﻣﺟﺔ اﻟﻣﺗﻘدﻣﺔ‪.‬‬ ‫‪1 ON‬‬ ‫‪ -‬اﺿﻐط ﻋﻠﻰ )‪ (+‬أو )‪ (-‬ﻟﺗﻐﯾﯾر اﻟرﻗم اﻷول ﺛم‬
‫ﻛرر اﻟﺧطوات اﻟﺳﺎﺑﻘﺔ ﺣﺗﻰ ﺗﻧﺗﮭﻲ ﻣن إدﺧﺎل اﻟرﻗم ﺑﺎﻟﻛﺎﻣل ﺣﺗﻲ ﺗظﮭر‬
‫ﻛﻠﻣﺔ ?‪ Store‬ﻓﻰ اﻟﻧﮭﺎﯾﺔ‪.‬‬ ‫اﺿﻐط ‪ ENTER‬وﻛرر ﻣﺎ ﺳﺑﻖ ﻟﺗﻐﯾﯾر ﺑﺎﻗﻲ ‪SET KEY CODE‬‬
‫>>‪<<123‬‬ ‫اﻷرﻗﺎم‪.‬‬
‫‪ -‬اﺿﻐط ﻋﻠﻰ ‪ ENTER‬ﺑﻌد اﻻﺧﺗﯾﺎر ﻟﻠﺣﻔظ ‪.‬‬
‫ﻣﻠﺣوظﺔ‪ :‬ﯾﺟب اﺧﺗﯾﺎر اﻟرﻗم اﻟﺳرى ﺿﻣن ﻧطﺎق‬
‫اﻷدوار اﻟﻌﺎﻣﻠﺔ‪.‬‬