MD03 - 24Volt 20Amp H Bridge Motor Drive

Overview
The MD03 is a medium power motor driver, designed to supply power beyond that of any of the low power
single chip H-Bridges that exist. Main features are ease of use and flexibility. The motor's power is controlled
by Pulse Width Modulation (PWM) of the H-Bridge at a frequency of 15khz ( 7.5khz before version 12).
The 15v MOSFET drive voltage is generated onboard with a charge pump, so the module requires only two
supply voltages;
1. A standard 5V supply for the control logic, only 50mA maximum is required.
2. The H-Bridge has a rating of 60v allowing Motor voltages up to 24vdc.
Control of the module can be any of;
a. I2C bus, up to 8 MD03 modules, switch selectable addresses.
b. 0v-2.5-5v analog input. 0v full reverse, 2.5v center stop, 5v full forward.
c. 0v-5v analog input with separate direction control
d. RC mode. Controlled directly from the RC receiver output.
e. PWM. A simple onboard filter means you can use a 0%-100% 20khz or greater instead of analog.

Motor connections

Note - There is no fuse on

the PCB. You should
provide a 25/30A fuse in
line with the +v battery
terminal.

Don't Ignore this, High

currents can be
dangerous!

Be sure to use cable rated for at least 25/30A for the Battery, Fuse and Motor leads.

Motor Noise Suppression

Please note that using motors with the MD03 as with any other electronic device requires suppression of noise.
This is easily achieved by the addition of a 10n snubbing capacitor across the motor. The capacitor should also
be capable of handling a voltage of twice the drive voltage to the motor.

Control Connections

The connections for use with

the I2C Bus are marked on the
PCB.

See text below for details of

the other modes.
Analog Mode - 0v-2.5v-5v
In this mode the motor is controlled by a 0v to 5v analog signal only on the SDA line. Pin SCL is unused and
should be connected to either +5v or 0v.
0v is maximum reverse power
2.5v is the center stop position
5v is full forward power
The is a small (2.7%) dead band around 2.5v to provide a stable off position. Input impedance is 47k.

Analog Mode - 0v-5v

In this mode the motor is controlled by a 0v to 5v analog signal on the SDA line and direction on SCL.
0v is stop position
5v is full power
Pin SCL is the logic level (ttl) direction control. logic 0 for reverse direction and logic 1 for forward direction.

You may also use a PWM signal instead of an analog voltage on the SDA line. There is a simple
resistor/capacitor filter on the module which will generate the analog voltage from the incoming PWM signal.
your PWM signal should be 20khz or greater in frequency and ideally, come from a CMOS gate (0-5v) rather
than ttl (0-3.5v ish). a 0% duty cycle will represent 0v and a 100% duty cycle representing 5v. This applies to
both the above analog modes. Note that the PWM input is not the same as the PWM motor drive which is
generated seperately.

RC Mode
This mode allows direct connection to standard model radio control receivers. Most receivers work from a
4.8v-6v battery pack and can be powered by 5v supply that powers the MD03 logic. The control pulse (Yellow)
from the receiver should be connected to the SDA terminal. The SCL terminal is unused and should be
connected to either +5v or 0v. Connect the receiver supply (Red) to +5v logic supply and the receiver 0v
ground (Black) to the MD03 logic ground. The output from an RC receiver is a high pulse 1.5mS wide when
the joystick is central. This varies down to 1.1mS and up to 1.9mS as the joystick is moved. This range can be
shifted by the centering control by +/-100uS from 1mS-1.8mS to 1.2mS-2mS. The MD03 provides full control
in the range 1.1mS to 1.9mS with 1.5mS being the center off position. There is a 7uS dead zone centered on
1.5mS for the off position. The Radio Transmitter centering control should be adjusted so that the motor is off
when the joystick is released.

RC Mode With Timeout (from version 12)

An extra mode has been added and operates in much the same way as the normal RC control. The difference is
the addition of a new timeout feature. If a RC pulse is not detected for a period in excess of 200ms, then the
motor will be stop being driven until a valid RC signal is received

I2C Mode
I2C mode allows the MD03 to be connected to popular controllers such as the PICAXE, OOPic and BS2p, and
a wide range of micro-controllers like PIC's, 8051's and H8's. There are instructions for connecting the MD03
to the OOPic here. If you're writing your own code in C, then we have some downloadable software to
communicate with the CMPS03 compass module, SRF08 sonar and MD03 motor driver here.

I2C communication protocol with the MD03 module is the same as popular eeprom's such as the 24C04. To
read one or more of the MD03 registers, first send a start bit, the module address (0XB0 is the base address)
with the read/write bit low, then the register number you wish to read. This is followed by a repeated start and
the module address again with the read/write bit high (0XB1). You now read one more registers. The MD03
has 8 registers numbered 0 to 7 as follows;

Register
Name Read/Write Description
Address
Write 01 Forwards - 02 Reverse
0 Command R/W
(00 for instant stop - Rev9 firmware only)
1 Status Read only Acceleration, Temperature and Current Status
2 Speed R/W Motor Speed 0-255 (0x00 - 0xFF)
3 Acceleration R/W Motor Acceleration 0-255 (0x00 - 0xFF)
4 Temperature Read only Module temperature
5 Motor Current Read only Motor Current
6 Unused Read only Read as zero
Software
7 Read only Software Revision Number- Currently 9
Revision

Command Register
Controls the motor start, stop and direction. Write 1 to drive forwards, Write 2 to reverse, Write 0 to stop
instantly (Rev 9 only). Be sure to have set the speed and acceleration before issuing these commands. Do not
write 0 to the command register to stop on firmware revisions earlier than 9.
Note - On all revisions the way to stop the motor is the same as other speed changes, write the new speed to the
speed register and re-issue the direction command. This will cause the motor to decelerate to a stop at the rate
set by the acceleration register. On Rev 9 firmware, writing zero the command register will stop the motor
instantly, bypassing the acceleration value.

Status Register
Shows the status of the MD03

Bit 7
6 5 4 3 2 1 Bit 0 (lsb)
(msb)
over- over-
Acceleration
Busy - - - - temperature current
in progress
limiter limiter

Bit 0 is read as high when the drive is still accelerating the motor to the requested speed. It will be cleared
when the requested speed is achieved or the over current or over temperature limiters are active.
Bit 1 set high indicates that the current through the motor has reached 20Amps and is being limited to that
value. The Red LED will be illuminated when this happens.
Bit 2 set high indicates that the over temperature limiter is active. Above a preset threshold, the motor current
will be reduced in proportion to the MD03 temperature. The module can still be used but the motor power will
be limited. The Red LED will be illuminated when this happens. It should be noted that a few minutes of
running continuously at 20A will cause the heatsink to get hot - watch your fingers!
Bit 7 is the busy flag. It is set high when you issue a new command to the module. It is cleared very quickly
and you are unlikely ever to see it set.

Speed Register
Sets the maximum speed that the motor will accelerate to. It is actually the 8-bit value sent to the modules
PWM controller. Write a value of 0 to 243 (numbers from 243 to 255 are clamped to 243) . The larger the
number, the more power is applied to the motor.

Acceleration Register
This sets the rate at which the motor accelerates or decelerates from where it is towards the new speed set by
the speed register. Write a value of 0 to 255, the larger the number the longer the module will take to reach the
new speed. Writing zero to the acceleration register will allow maximum acceleration of 0 to full in 0.187
seconds. This value actually controls a timer which steps the current motor speed towards the requested motor
speed. It does this every (((acceleration register)*125)+768)uS. A value of zero gives 768uS/step or
243*768=186624uS (0.187s) to accelerate from 0 to full. A value of 255 is ((255*125)+768)*243=7932249uS
or just under 8 seconds.

Temperature Register
This is the value used internally to limit the motor current if the module gets too hot. You do not need to read
or do anything with it. It does not read degrees, in fact the number goes down as the temperature goes up! It is
actually reading the forward voltage drop of a diode located under the 0.003R current sense resistor. The
number drops by 1 count approx. every 1.42 degrees C.

Motor Current
This is the value used internally to limit the motor current to 20A. You do not need to read or do anything with
it. The value is proportional to motor current, with a value of 186 representing the 20A limit.

Software Revision number

The revision number of the software in the modules PIC16F872 controller - currently 13 as of 1st August 2005.

Mode Switches
The 4 mode switches set the operating mode of the MD03. They are read once only when the module is
powered up. You cannot switch modes while the unit is on.

Mode Switch 1 Switch 2 Switch 3 Switch 4

I2C Bus - address 0xB0 On On On On
I2C Bus - address 0xB2 Off On On On
I2C Bus - address 0xB4 On Off On On
I2C Bus - address 0xB6 Off Off On On
I2C Bus - address 0xB8 On On Off On
I2C Bus - address 0xBA Off On Off On
I2C Bus - address 0xBC On Off Off On
I2C Bus - address 0xBE Off Off Off On
0v - 2.5v - 5v Analog On On On Off
0v - 5v Analog + Direction Off On On Off
Radio Control On Off On Off

New Mode (from version 12)

Radio Control, timeout on Off Off On Off

All other combinations are invalid, the LED will blink and nothing else will happen.
Note that I2C addresses are the upper 7 bits. Bit 0 the the read/write bit, so addresses 0xB0/0xB1 are write/read
respectively to the same address.

General Usage
The MD03 can handle high currents, and you will need to take a few precautions with wiring. It is very
important that you do not allow motor current to flow in the logic ground path. Don't assume that just because
the Battery, MD03 and Controller grounds are all together, that all is well. If at all possible, use two batteries,
one for the logic and and the other for the motor power. Don't connect the battery grounds together, that is
already done on the MD03. If you do, then you will only create a ground loop - and problems. The diagram
below shows the general idea on keeping the logic and power sides electrically and physically separate from
each other.

PCB Drill Plan

The following drawing shows the MD03 mounting hole positions.

Schematics
The MD03 schematics in GIF format md03sch1 md03sch2

CPU Code
For those who wish to, and are able to re-flash the PIC16F872, here is the Hex (Revision 13)