SEAT NO.

_______

PREBOARD EXAMINATION NO.2

MACHINE DESIGN, MATERIALS AND SHOP PRACTICE A. Flank C. Lips
SET A B. Fillet D. Flutes
14. The inside diameter of an air cylinder is 50 mm
INSTRUCTION: Select the correct answer for each and can handle a pressure of 10 Mpa. Assuming
of the following questions. Mark only one answer an allowable tensile stress of the cylinder
for each item by shading the box corresponding material of 50 Mpa, determine the required
to the letter of your choice on the answer sheet thickness of this cylinder.
provided. STRICTLY NO ERASURES ALLOWED. A. 5.61 mm C. 4.61 mm
B. 5.01 mm D. 4.01 mm
1. A 100 inches long aluminum bar is subjected to 15. Find the force required to punch a 25-mm hole
a tensile stress of 25,000 psi. Find the in a 20-gage (0.9525 mm) steel plate if the
elongation if E = 10 x 10^6 psi. shearing strength of the material is 400
A. 0.025 in C. 0.45 in MN/m(squared).
B. 0.25 in D. 0.65 in A. 29.9 kN C. 32.4 kN
2. A double threaded bolt having a 5 threads per B. 22.4 kN D. 24.5 kN
inch. Compute the lead, in inches, of a screw 16. What is a unique form of cast iron with worm
in one turn. shaped graphite particles?
A. 0.2 C. 0.5 A. Wrought iron
B. 0.4 D. 1.0 B. Mottled cast iron
3. A flywheel has diameter of 1.5 m and a mass of C. Compacted graphitic iron
1000 kg. What torque is needed to produce an D. Malleable cast iron
angular acceleration of 120 revolutions per 17. How long will it take to drill a hole through a
minute, per second? 10 cm thick steel plate if the drill feed is 0.1
A. 3534 J C. 3345 J mm per rev and a ¼ in diameter drill is turning
B. 3354 J D. 3453 J at 750 rpm?
4. Determine the power developed by the shaft A. 80 sec C. 500 sec
rotating at 1200 rpm and the twisting moment of B. 100 sec D. 1000 sec
1050 in-lb. Shear stress of the shaft is 6500 18. A flanged coupling is designed to use 6 bolts
psi. on a 4-in diameter bolt circle. The allowable
A. 10 HP C. 18 HP stress in shear is 12,000 psi; the maximum
B. 15 HP D. 20 HP torqued is 50 ft-lbf. Find the diameter of the
5. 120 tooth gear 14 ½ degree involute pressure bolt required.
angle of unknown speed meshed with a 36 tooth A. 0.032 in. C. 0.073 in.
pinion turning at 300 rpm. Determine the unknown B. 0.064 in. D. 0.086 in.
speed of the gear if the power transmitted is 19. If a car wheel is 60 cm diameter and a rim Is
15 kW and tooth thickness of 20 mm. 0.90 mm smaller ID, to what temperature would
A. 1000 rpm C. 90 rpm it be necessary to heat the rim to provide a
B. 100 rpm D. 45 rpm 0.100 mm clearance to assemble the rim on the
6. A cantilever beam is 5 ft long and square cross- wheel? Both members are made of steel. Dry Ice
section, 2 inches on each side, is loaded at its at negative 79 deg C is available to cool the
end by a vertical force of magnitude 500 lbs. wheel. Ambient temperature is 20 deg. C.
Find the radius of gyration of the beam. A. 45.6 deg.C C. 32.5 deg.C
A. 1 inch C. 1.33 inch B. 43.4 deg. C D. 63.4 deg. C
B. 0.576 inch D. 2 inches 20. Calculate the cutting speed in feet per minute
7. Determine the length of a square key for gear if the spindle speed of a 3/4 in drill is 400
driven shaft transmits 40 kW at 300 rpm. The rpm.
shaft diameter is 60 mm with design stress of A. 157 fpm C. 15.24 fpm
70 Mpa in shear, the thickness and width of the B. 36 fpm D. 78.5 fpm
key is 3/8 in. 21. That surface on a drill point which extends
A. 43 mm C. 64 mm behind the lip to the following flute.
B. 56 mm D. 72 mm A. Grub C. Quill
8. A key that allows the hub to move along the B. Flank D. Crest
shaft but prevents the rotation of the shaft. 22. A draft horse walks at the rate of 5 km/hr. What
A. Woodruff key C. Gibs key uniform force in Newton must he exert if the
B. Feather key D. Square key output power is exactly two kilowatt?
9. Determine the maximum permissible velocity V in A. 1.44 kN C. 0.720 kN
a cast iron rim of a flywheel the maximum B. 3.4 Kn D. 720 kN
allowable tensile stress in cast iron is 4000 23. A 150 hp motor turns a shaft at 2400 rpm. The
psi. The cast iron weighs 0.255 lb/cu in. shaft steps down in diameter from 3.0 to 2.5
A. 54.5 m/s C. 62.5 m/s inches. Calculate the maximum torsional shear
B. 205 m/s D. 125 m/s stress if the stress concentration factor is
10. A steel rod 30 ft long used in a control given to be 1.3.
mechanism must transmit a tensile force of 980 A. 1800 psi C. 1720 psi
lb without stretching more than 1/8 in, nor B. 1670 psi D. 1140 psi
exceeding an allowable stress of 20,000 psi. 24. A gear of 80 teeth and a pinion of 20 teeth has
What must be the diameter f the rod be? (E = 30 a gear and pinion ratio of 4. Find the diametral
x 10^6 psi) pitch of these gears if the center distance is
A. ¼ in C. ½ in 20.
B. 3/8 in D. ¾ in A. 2.0 C. 3.0
11. The diameter of a solid shaft that rotates 100 B. 2.5 D. 3.5
rpm and transmits 1.2 hp is 7/8 inch. Calculate 25. Which type of key is used for mounting shifting
the design stress (for shear) if the shaft is gears in gear boxes?
subjected to torsion only. A. Splines C. Square
A. 7000 psi C. 8000 psi B. Saddle D. Flat
B. 6000 psi D. 5000 psi 26. A pulley 2, 24 inches in diameter and keyed to
12. A multiple-disc clutch consists of 10 steel a shaft A turning 360 rpm, has belt connected
discs and 9 bronze discs. The effective outside to a pulley 4, 36 inches in diameter, on another
and inside diameters are 8 inches and 6 inches shaft B. Find the speed of the pulley 4.
respectively. If an axial force 120 lb is A. 240 rpm C. 360 rpm
applied and the shaft turns at 1000 rpm, find B. 180 rpm D. 120 rpm
the horsepower capacity. Assume the coefficient 27. A jackscrew has a pitch of 3 mm and handle 600
of friction of 0.35 and uniform wear. mm long. A force of 60 N must be applied when a
A. 42 hp C. 55 hp load of 25 kN is being lifted. Calculate the
B. 25 hp D. 20 hp Ideal Mechanical Advantage.
13. Grooves in the body of the drill which provide A. 1257 C. 0.33
lips and permit the remove of chips and allow B. 2.4 D. 416.67
cutting fluid to reach the lips.
Continued on Page 2
 SEAT NO._______

PREBOARD EXAMINATION NO.2

28. A flywheel weighing 6 kN has a mean diameter of B. 25.2 hp D. 15.7 hp
90 cm. The maximum speed of the flywheel is 7 41. The axial force required is 150 N when the
rev/sec down to 4 rev/sec during the shearing capacity of the clutch is 8 kW at 500 rpm. What
process. Determine the energy released by the is the mean diameter of the active conical
flywheel. sections when the cone clutch has an angle of
A. 7856 kg-m C. 9872 kg-m 10 degrees and coefficient of friction of 0.5?
B. 8145 kg-m D. 8241 kg-m A. 508 mm C. 608 mm
29. Part of the drill bit that fits into the holding B. 808 mm D. 708 mm
device. 42. The train value of gear train is _________.
A. shank C. Flute A. equal to the speed ratio
B. tang D. point B. double the speed ratio
30. A 2-ft inside diameter spherical vessel has a C. half of the speed ratio
wall thickness of 3 inches. Compute for the D. reciprocal of the speed ratio
tensile at its inner surface as caused by an 43. What is the length of a piece of stock with
internal pressure of 1500 psi and an external taper per inch of 3/16 if has a diameter of 3
pressure of 300 psi. inches at one end and 1.5 inches at the other
A. 3123.87 psi C. 1833.33 psi end?
B. 4113.38 psi D. 1244.25 psi A. 4 in C. 8 in
31. When a column is subjected to an eccentric load, B. 10 in D. 6 in
the stress induced in the column will be 44. A short cylindrical cast iron post supports a
_______. compressive load of 20 tons. Compute the
A. both direct and bending stress diameter of the post if the factor of safety is
B. shearing stress only 10 and the compressive stress as given in the
c. bending stress only table is 80 ksi.
D. direct stress only A. 6.41 cm C. 25.2 mm
32. A 2 ft diameter solid disc flywheel weighs 200 B. 2.52 cm D. 6.41 in
lbs and is designed to handle 1600 ft-lb kinetic 45. Is the irregularities or departures from nominal
energy change. Its upper speed is 40 fps. Find surface of greater spacing than roughness.
the coefficient of regulation. A. smoothness C. waviness
A. 0.491 C. 0.419 B. lay D. roughness
B. 0.194 D. 0.149 46. A coil spring 4 cm in outside diameter made of
33. A pair of mating spur gears have 14 ½ deg. Full 5 mm wire is to support a mass of 45 kg,
depth involute teeth of 2.5 diametral pitch. The calculate the spring stress concentration
pitch diameter of the smaller gear is 6.4 factor.
inches. If the transmission ratio 3 to 2. A. 1.213 C. 1.143
Calculate the addendum. B. 1.718 D. 1.071
A. 0.462 in. C. 0.4 in. 47. During a stress-strain test, since the given
B. 0.862 in. D. 0.57 in. stresses are below the proportional limit, the
34. An 8-ft-diameter spherical pressure vessel is unit deformation at a stress of 35 MPa was
made by bolting two hemispherical flanged observed to be 123 x 10 to the minus 6 m/m and
sections together. How many 1-in diameter bolts a stress of 135 MPa, it was 321 x 10 to the
are required to secure two halves if the minus 6 m/m. If the proportional limit was 150
pressure within the vessel is 25 psi? Use MPa, compute for the strain in in/ in
working stress of 15,000 psi and a cross- corresponding to the stress of 100 000 kPa.
sectional area of 0.551 sq in for the bolts. Express your answer in three significant digits.
A. 24 C. 20 A. 2.68 x 10 to the minus 4 in/ in
B. 22 D. 28 B. 3.18 x 10 to the minus 4 in/ in
35. Which of the following superalloys is age- C. 4.67 x 10 to the minus 4 in/ in
hardenable? D. 1.89 x 10 to the minus 4 in/ in
A. Stellite C. Nimonic 48. Is the direction of the predominant surface
B. Incoloy D. Inconel pattern
36. A mass, m, of 0.020 kg is hanging from a spring A. smoothness C. waviness
whose spring constant, k, 0.44 N/m. If the mass B. lay D. roughness
is pulled down and released, what is the period 49. The backbone of the drill bit and it is the
of oscillation? narrow section between the flutes.
A. 1.34 s C. 1.5 s A. Body C. Cone
B. 0.50 s D. 2.1 s B. Web D. Margin
37. A 100-ton hydraulic jack has an 8-in diameter 50. An 18-tooth straight spur gear transmits a
piston and a cylinder thickness of t. Find the torque of 1200 N-mm. The pitch circle diameter
appropriate wall thickness if the cylinder is is 19 mm, and the pressure angle is 14.5 ½. What
fabricated from high-strength steel having a is the radial force on the gear?
permissible working stress of 40,000 psi in A. 126.32 N C. 133.3 N
tension. B. 66.7 N D. 63.15 N
A. 0.54 in C. 0.40 in 51. Which of the following is a single crystal grown
B. 0.30 in D. 0.36 in by vapor deposition?
38. A wet, steel-backed asbestos clutch with A. Glass C. Ceramics
hardened steel plates is being designed to B. Roving D. Whisker
transmit 33 N-m. The coefficient of friction is 52. Two extension springs are hooked in parallel and
0.12. Slip will occur at 300% of the rated support a load of 100 lb. One spring has a
torque. The maximum and minimum friction surface constant of 50 lb/in and the other a constant
diameters are 115 mm and 65 mm respectively. The of 100 lb/in. What is the deflection of the
contact pressure is 700 kPa. How many plates are load?
needed? A. 16.94 mm C. 0.667 mm
A. 4 C. 3 B. 76.3 mm D. 66.7 mm
B. 6 D. 5 53. What is the outside diameter of a hollow shaft
39. The groove of the drill bit and carries out the replacing a 150 mm diameter solid shaft with
chips and admits the coolant. equal torsional strength and 50% weight saved?
A. flute C. lips A. 180 mm C. 160 mm
B. Body D. point B. 190 mm D. 170 mm
40. A multiple-disc clutch consists of 10 steel 54. What is the circular pitch of a spur gear with
discs a d 9 bronze discs. The effective outside clearance of 0.05 in?
and inside diameters are 8 inches and 6 inches A. 2 C. 3
respectively. If an axial force 100 1b is B. 4 D. 1
applied and the shaft turns at 1000 rpm, find 55. A grindstone has a moment of inertia of 1.6 x
the horsepower capacity. Assume the coefficient 10 kg.m (squared). When a constant torque is
of friction of 0.25 and uniform pressure. applied, the flywheel reaches an angular
A. 32.5 hp C. 43.7 hp velocity of 1200 rpm in 15 seconds. Assuming it
Continued on Page 3
 SEAT NO._______

PREBOARD EXAMINATION NO.2

started from rest, find its angular acceleration 0.12. Find the tangential force on the gear in
in rad/s(squared)? lbs.
A. 8.38 C. 6.42 A. 548 lbs C. 821.74 lbs
B. 3.24 D. 7.48 B. 730.43 lbs D. 620 lbs
56. Is the relatively finely spaced irregularities 70. A double threaded right- handed worm gear
of the surface. transmits 15 Hp at 1150 rpm. The pitch of the
A. smoothness C. waviness worm is 3/4 inches and pitch diameter of 3
B. lay D. roughness inches. The pressure angle is 14 " degrees and
57. A helical coil spring has a mean coil diameter the coefficient of friction is 0.12. Compute for
of 1 in. and a wire diameter of 1/10 inch. the tangential force on the worm, express the
Determine the curve correction factor of the answer in pounds.
spring. A. 840 C. 498
A. 1.1414 C. 1.0903 B. 950 D. 548
B. 1.1144 D. 1.3090 71. Surface hardening is desirable for a product
58. Which of the following is available in five that subject to _________.
slightly different nominal composition for A. fatigue C. high shear loads
applications which require high strength, good B. high impact loads D. high tensile loads
fabricating and fusing qualities, immunity to 72. The energy of recoil of a rocket launcher of
rust, free machining and a corrosion resistance mass 4536 kg is absorbed in a recoil spring. At
equivalent to copper? the end of the recoil, a damping dashpot engages
A. Everdur C. Dynavar sq that the launcher returns to the firing
B. Silicon D. Titanium position without any oscillation (critical
59. A solid transmission shaft is 3.5 inches in damping). The launcher recoils 3 m with an
diameter. It is desired to replace it with a initial speed of 12 m/s. Compute the recoil
hollow shaft of the same material and the same spring constant.
torsional strength, but its weight should only A. 40.5 kN/m C. 30.5 kN/m
be half as much of the solid shaft. Find the B. 25.3 kN/m D. 72.5 kN/m
difference of the outside and inside diameter 73. A 1/4 inch cone pointed setscrew Is spotted one-
of the hollow shaft in mm. half of the length of the cone. The cone angle
A. 20.34 mm C. 16.15 mm is 118 degrees and the allowable shearing stress
B. 10.99 mm D. 34.02 mm of the setscrew material is 10,000 psi. Find the
60. The most common flux to use when soldering holding power of the setscrew when it is
brass, copper or tin is: securing a pulley to a 1/2 inch shaft.
A. hallow C. borax A. 490.87 lbs C. 1963.50 lbs
B. rosin D. salt ammonia B. 245.44 lbs D. 122.72 lb
61. The engineering stress in a solid tension member 74. How many revolutions are needed to lift table
was 324 MPa at a failure. The reduction in area of height 300 mm if a machine table is lifted
was 80%. What was the true strain at failure? by means of a two start screw thread which has
A. 1.61 C. 1.24 a pitch of 6 mm?
B. 1.16 D. 1.42 A. 20 C. 30
62. Steels containing large amounts of mild nickel B. 50 D. 40
and chromium: 75. When crank rotates with uniform speed, it has
A. carbon steel C. alloy steel _________ acceleration only.
B. stainless steel D. cast steel A. tangential C. coriolis
63. Two sheets of aluminum on an aircraft wing are B. radial D. gyroscopic
to be held together by aluminum rivets of cross- 76. A helical extension spring is wound from 0.07
sectional area of 0.25 sq. in. The shearing in.-diameter wire with a mean diameter of helix
stress on each rivet must not exceed one-tenth of 0.75 inch. Find the approximate value of the
of the elastic limit for aluminum. How many load that the spring can sustain before
rivets are needed if each rivet supports the noticeable deflection occur. Note: shearing
same fraction of a total shearing force of stress is 21,000 psi.
25,000 lbs? Assume that the elastic limit stress A. 2.78 lb C. 3.57 lb
is 131 Mpa. B. 4.37 lb D. 5.76 lb
A. 10 rivets C. 35 rivets 77. A single threaded trapezoidal metric thread has
B. 20 rivets D. 53 rivets a pitch of 4mm, and a mean diameter of 18mm. It
64. What do you call the difference between the is used as a translation screw in conjunction
higher limit and lower limit of size? with a collar having an outside diameter of 37mm
A. Allowance C. Interference zone and an inside diameter of 27mm. Find the
B. Tolerance D. Deviation required torque in N-m to raise a load of 400kg
65. A solid steel machine shaft with a safe shearing if the coefficient of friction is 0.3 for both
stress of 7000 psi transmits a torque of 15,500 thread and collar.
in-lb. What is the length of the square key if A. 52.6 C. 33.2
it 1.5 times the diameter of the shaft? B. 45.8 D. 32.6
A. 2.0 in C. 1.75 in 78. In the LRT II project, steel railroad rails of
B. 2.5 in D. 3 in 10 meters long are to be installed. If lowest
66. A ¼ -in fillet weld 2 in long carries a steady temperature considered is 16degC, and a maximum
load of 3,000 lb lying along the weld. The weld temperature of 36C is designed, assuming
metal has a yield strength of 50, 000 psi. Find coefficient of thermal expansion of steel to be
the value of the factor or safety. 11.6 x 10^-6 m/m-C and modulus of elasticity of
A. 1.75 C. 1.45 steel to be 207 Gpa, determine the clearance
B. 2.95 D. 3.2 between rails such that the adjoining rail will
67. What is most nearly the elongation of the just touch at maximum design temperature.
aluminum bar of length 2.5 ft (cross section of A. 1.32 mm C. 3.32 mm
3 cm x 3 cm) when loaded to its yield point? E B. 2.32 mm D. 4.32 mm
= 69 Gpa, and Syield = 255 Mpa. Neglect the 79. A double thread worm has a pitch diameter of 3
weight of the bar. inches. The wheel has 22 teeth and a pitch
A. 12 mm C. 2.8 mm diameter of 5. Find the gear helix angle?
B. 15 mm D. 9.3 mm A. 9.46 deg C. 8.61 deg
68. In a pressure vessel, the ratio of minimum B. 4.69 deg D. 6.18 deg
strength of joint to the strength of solid joint 80. What accounts for the backlash of spur gears?
is known as A. Both module and pitch line velocity
A. efficiency C. joint efficiency B. Pitch line velocity
B. Performance factor D. relative strength C. Module
69. A double threaded right hand 3.0 in worm gear D. Tooth profile
transmit 20 hp at 1,550 rpm. The pressure angle 81. A clutch system is going to transmit 40 hp
is 14.5 deg. and the coefficient of friction is between two shafts. One of the shafts is not
rotating at the time of coupling. The speed of
Continued on Page 4
 SEAT NO._______

PREBOARD EXAMINATION NO.2

the rotating shafts is 1000 rpm. The clutch stress in the rails if during high summer
diameters of the disk are 2 inches and 8 inches. temperature of 40C occur.
The total mass moment of inertia of the system A. 2.5 Mpa C. 9.6 Mpa
is 20 lb-in-s(square). Find the axial force for B. 5.4 Mpa D. 6.9 Mpa
successful coupling based on uniform pressure. 94. A body hangs from an ideal spring. What is the
The friction coefficient between linings is frequency of oscillation of the body if its
0.30. mass, m, 0.015 kg, and k is 0.50 N/m?
A. 4000 lb C. 3000 lb A. 0.66 Hz C. 0.78 Hz
B. 3540 lb D. 2643 lb B. 0.92 Hz D. 0.351 Hz
82. A heavy-duty sleeve bearing is used with good 95. A 4-mm fillet weld 50 mm long carries a steady
ventilation. The bearing has a diameter of 2 in load P lying along the weld. IF the working
and a length of 4 in. The load on the bearing stress in shear is taken as 78 Mpa. Calculate
is 2200 lb. A shaft rotates 200 rpm in the the load it can carry.
bearing. Find the heat radiating capacity. The A. 18 kN C. 15 kN
coefficient of friction is 0.02. B. 11 kN D. 20 kN
A. 0.7404 Btu/min-sq.in 96. A flywheel weighing 4,480 lbs has a radius of
B. 0.8765 Btu/min-sq.in gyration of 3 feet. If there is a driving torque
C. 0.7654 Btu/min-sq.in of 600 ft-lb and a resisting torque of 250 ft-
D. 0.8043 Btu/min-sq.in lbf, find the time required to increase the
83. Sevolute functions are used in calculating the speed from 20 to 80 revolution per minute.
form diameter of involute splines. What is the A. 22.5 s C. 15.4 s
sevolute of 20 degrees? B. 20.5 s D. 12.5 s
A. 2.77 C. 0.636 97. The center of a wheel with an outer: diameter
B. 1.049274 D. 0.0149 of 610 mm is moving at 12.5 m/ s. There is no
84. Which type of gears are used for shaft axes slippage between the wheel and the surface. A
having an offset? valve stem is mounted 150 mm from the center.
A. Hypoid gear C. Zerol gear What is the velocity of the valve stem when it
B. Spiral Bevel gear D. Mitre gear is 45 degrees from the horizontal?
85. The shearing stress in a piece of structural A. 12.5 m/s C. 20.62 m/s
steel s 14.51 ksi. If the modulus of rigidity G B. 17.4 m/s D. 40.98 m/s
is 85 Gpa, find the shearing strain. 98. A flywheel on a press rotating at 120 rpm is
A. 0.00231 C. 0.00117 slower down to 102 rpm during a punching
B. 0.00542 D. 0.850 operating that requires ¾ second for the
86. A solid machine shaft with a safe shearing punching portion of the cycle. What angular
stress of 7000 psi transmits a torque of 10,500 deceleration does the flywheel experience in
in-lb. A square key is used whose width is equal radians per sec per sec?
to the shaft diameter and whose length is A. -2.52 C. 2.52
1.5times the shaft diameter. What is the length B. -2.25 D. 2.25
of the key? 99. How long in minutes will it take to saw a
A. 7.5 cm C. 4.9 cm rectangular piece of aluminum plate 8 inches
B. 2.9 cm D. 1.9 cm wide and 1.5 inches thick if the length of the
87. The cutting speed for turning a 4-inch diameter cut is 8 inches? The power hacksaw makes 2.5
bar has been found to be 545 fpm. Calculate the revolutions per second and the average feed per
lathe spindle speed? stroke is 0.006 inch.
A. 549 rpm C. 520 rpm A. 9.78 min C. 10.78 min
B. 600 rpm D. 750 rpm B. 8.89 min D. 5.29 min
88. Which of the following device is used for 100. A 1000 lbs flywheel has a torque capacity of
transmitting energy in CNC Machine tools? 2600 ft lb. The speed is to be maintained between
A. Recirculating ball screw and nut assembly 100 and 120 rpm. The effect of the arms and hub
B. Screw and nut assembly accounts for 10% of the rim weight. Find the
C. Pulley and belt mean diameter of the flywheel.
D. Gears A. 35.36 in C. 38.63 in
89. Two shafts are connected by spur gears. The B. 44.65 in D. 42.78 in
pitch radii of gears A and B are 4 inches and
20 inches respectively. If shaft A makes 800 rpm
and is subject to twisting moment of 1000 inch- ***END***
pound. What is the tooth pressure of gear B?
A. 250 lb C. 320 lb
B. 150 lb D. 100 lb WARNING: Failure to submit your Test Questions
90. A slab-milling operation is being carried out (Complete) set will cause the cancellation of your
on 12-in long, 4-in wide annealed mild-steel Test-Results for the subject.
block at a feed 0.01 in/ tooth and a depth of
cut 1/8 in. The cutter is 2 inches in diameter,
has 20 straight teeth, rotates at 100 rpm, and
is wider that the block to be machined.
Calculate the linear speed of the work piece.
A. 50 in/min C. 25 in/min
B. 40 in/min D. 20 in/min
91. A plate clutch with a single friction surface
is 10 inches O.D. and 4 inches I.D. If the
uniform wear is valid, find the torque for
maximum pressure of 100 psi. (Friction Coef. =
0.2)
A. 3249 in-lbf C. 3124 in-lbf
B. 2344 in-lbf D. 2639 in-lbf
92. A 40-tooth steel gear has a diametral pitch of
2. The pressure angle is 14 ½ degrees. Find the
circular pitch.
A. 0.50 C. 1.571
B. 1.5 pi D. 0.579
93. In the LRT II project, steel railroad rails of
10 meters long are to be installed. If lowest
temperature considered is 16degC, and a maximum
temperature of 36C is designed, assuming
coefficient of thermal expansion of steel to be
11.6 x 10^-6 m/m-C and modulus of elasticity of
steel to be 207 Gpa, determine the induced