Scribd
Upload
48 views9 pages

Elnvip Manual

The document provides installation and operation instructions for an electrical multimeter device. It details mechanical installation, wiring, specifications, settings for current and voltage transformers, viewing electrical values, minimum/maximum readings, voltage indications, and no voltage/phase order alarms.

Uploaded by

petitaland
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
48 views9 pages

Elnvip Manual

The document provides installation and operation instructions for an electrical multimeter device. It details mechanical installation, wiring, specifications, settings for current and voltage transformers, viewing electrical values, minimum/maximum readings, voltage indications, and no voltage/phase order alarms.

Uploaded by

petitaland
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

ElNet VIP

Current & Power Multimeter


Rev 1.7
Table of Contents

1. Mechanical Installation ................................ ..................... 3


2. Wiring diagram ................................ ................................ .. 4
3. Specifications ................................ ................................ ..... 5
1.3 Technical Specifications ................................ ............. 5
3.2 Measuring Specifications................................ ........... 5
4. Current transformer ratio settings ................................ .... 6
5. Voltage transformer ratio settings ................................ ..... 6
6. Electrical values display ................................ .................... 7
7. Electrical values display ................................ .................... 7
8. Minimum \ Maximum values display ................................ 8
9. Indication led ................................ ................................ ..... 8
10. No volt relay ................................ ................................ ....... 9
10.1 General: ................................ ................................ ..... 9
10.2 No volt alarm setting: ................................ ............... 9
10.3 Phase order alarm: ................................ ................... 9

2
Dear customer, thank you for selecting the VIP Multimeter
for measurements of voltage, current, power and power
factor.

1. Mechanical Installation

Comment: Please do not install the VIP Multimeter close to


electrical bars.
Please leave enough space for approaching the device from its
back side for providing technical support.

1.1 Please choose the proper place for installation in panel and prepare
a square hole according to exhibit below.

Height
90 mm
Width
NOTE! 90 mm

Space in the electrical panel

1.2 Please insert the VIP Multimeter into the suitable space which is
to be prepared in advance. Make sure that the device is inserted in
the right direction. The device has a plastic knob which adjusts
itself for installation in electrical panels. The thickness of the
panel door should be less than 4 mm.

3
2. Wiring diagram

4
3. Specifications

3.1 Technical Specifications

Item Description
Power requirements 110 or 220 VAC ± 10%, 60/50 Hz, 20VA
Dimensions (HxWxD) 96x96x80 mm
Shipping Weight 514 gr.
Voltage limits 1000VAC
Current limits 50A
Enclosure material ABS + Antiflame
Operating temperature -20 - + 70 C
Storage temperature -20 - + 80 C
Humidity 0- 90 RH%
Voltage input terminals VL – E10 1708
Mounting Front panel mounting
Digital Output (optional) Dry contact

3.2 Measuring Specifications

Measurement Parameter Display Range Measuring in Display Range


in direct direct
connection connection
(scaling factor 1) (scaling factor 1)
Current 0.01 – 6A 0.01 – 6A 0.01 – 999KA
Neutral Current 0.01 – 6A 0.01 – 6A 0.01 – 999KA
(calculated )
Voltage L-N 0.00 – 650 V 0.00 – 650 V 0.01 – 999KV
Voltage L-L 0.00 – 650 V 0.00 – 650 V 0.01 – 999KV
Frequency (Hz) 45.1-65.1 Hz 45.1-65.1 Hz 45.1-65.1 Hz
Active power total\phase 0.00W – 999KW
Reactive power 0.00VAR -
total\phase 999KVAR
Apparent power 0.00VA -
total\phase 999KVA
Power Factor (cap.\ind.) -1.00 ÷ 1.00 -1.00 ÷ 1.00 -1.00 ÷ 1.00

5
4. Current transformer ratio settings

4.1 Press the "Enter" button for about 6 seconds.


4.2 The enter password screen will appear: "COD".
4.3 Use ↑ ↓ button to change the code to "1" and press Enter.
4.4 The current transformer set screen will appear, on the second line
the secondary value of current transformer (5A).

4.5 The headline "SET" will be displayed on the screen, on the


second line the secondary value of current transformer (5A), the
third line allows to define the value of the primary current
transformers with the "↑ ↓" buttons. At the end press Enter.

5. Voltage transformer ratio settings

5.1 In order to set the voltage transformer repeat the steps that
mentioned in paragraph 4. Instead entering code “1” enter the
code”11”. On the second line the secondary value of voltage
transformer (110V).

6
6. Electrical values display

6.1 Click on the “V/I/P” button, each additional click will zoom to
the next measured item or use the "↑ ↓" buttons (each click scrolls
the screens circularly), it is possible to browse among all the
display screens including three-phase display of voltage, current,
power, frequency, power factor. For automatically swapping
displays click on the “V/I/P” and hold for 6 seconds until the
automatically swapping mode will begin.

7. Electrical values display

7.1 Click on the “V+I+P” button, each additional click will zoom to
the next measured item or use the "↑ ↓" buttons (each click scrolls
the screens circularly) to scroll between combined screens of
voltage, current and power factor for each phase. For
automatically swapping displays click on the “V+I+P” and hold
for 6 seconds until the automatically swapping mode will begin.

7
8. Minimum \ Maximum values display

8.1 Clicking on the “Min/Max” button will zoom to the next


Min\Max item or use the "↑ ↓" buttons (each click scrolls the
screens circularly). The first screens present the highest measured
values of voltage and current (Hi); the next screens present the
lowest measured values of voltage and current (Lo) and then
respectively high and low frequency and power factor for each
phase.

9. Indication led

9.1 The indication led easily enables to identify whether there is


voltage in phases L1, L2, L3. In case there is voltage in phases
connections the led will be turned on (50 VAC at least).

8
10. No volt relay

10.1 General:
When the voltage is proper (above 50VAC, adjustable) and the
phases' order is proper the indication relay is closed, as appears
at the wiring diagram. The maximum current that is possible to
transfer through this relay is 150ma which is enough to operate
a regular control relay.

10.2 No volt alarm setting:


10.2.1 In order to set the minimum voltage value for the no
volt relay press the "Enter" button for about 6 seconds.
10.2.2 Use the "↑ ↓" buttons to change the password to "code
21" and press "Enter".
10.2.3 "SET AL" will appear and it would be possible to set
the min. voltage ratio by using the "↑ ↓". After setting
this value save it by pressing the "Enter" button.

10.3 Phase order alarm:


10.3.1 In order to turn ON/OFF the phase order relay, press
the "Enter" button for about 6 seconds.
10.3.2 Use the "↑ ↓" buttons to "code 31" and press Enter.
10.3.3 The phase order screen will appear and it would
enable you to select YES/NO (equivalent to
ON/OFF). After setting the desirable option save it
by pressing the "Enter" button.

You might also like