Scribd
Upload
72 views3 pages

BEC303 Set1

The document outlines a model question paper for an electronics principles and circuits course. It includes 10 questions across 5 modules covering topics like biasing circuits, MOSFET amplifiers, DACs, filters, thyristors, and feedback amplifiers. Students must answer 5 questions total, with at least 1 from each module. Questions involve circuit analysis, design specifications, derivations of expressions, and explanations of circuit operations.

Uploaded by

vedd22ece
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
72 views3 pages

BEC303 Set1

The document outlines a model question paper for an electronics principles and circuits course. It includes 10 questions across 5 modules covering topics like biasing circuits, MOSFET amplifiers, DACs, filters, thyristors, and feedback amplifiers. Students must answer 5 questions total, with at least 1 from each module. Questions involve circuit analysis, design specifications, derivations of expressions, and explanations of circuit operations.

Uploaded by

vedd22ece
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

BEC303

Model Question Paper-I with effect from 2023-24 (CBCS Scheme)


USN

Third Semester B.E. Degree Examination


Electronic Principles and circuits
TIME: 03 Hours Max. Marks: 100

Note: 01. Answer any FIVE full questions, choosing at least ONE question from each MODULE.

Bloom’s
Q.No Question Marks
Level
MODULE-1
1 a. Develop an expression for the operating point IC and VCE for the voltage 10 L3
divider bias circuit using approximate analysis. Also Calculate the
operation point for the VDB circuit given Vcc=10V, R1=10KΩ, R2=
2.2KΩ, Rc= 3.6KΩ, RE= 1KΩ
b. For the circuit shown in Fig 1b, determine the voltage gain and ac 10 L3
load voltage if β = 150

Fig 1b

OR
2 a. Design the voltage divider bias circuit to meet the following specifications 10 L3
Vcc=10V, VCE at mid point, stiff voltage divider, collector current 1mA,
βdc = 70 -200
b. For the circuit shown below in Fig 2b, the ac generator has an 10 L3
internal resistance of 600Ω for a voltage divider circuit. Determine
the output voltage if β = 300

Fig 2b

MODULE-2
3 a. With neat circuit diagrams, explain biasing of MOSFET by fixing the 10 L3

Page 01 of 02
BEC303
gate voltage
b. With neat circuit diagram, develop an expression for voltage gain, 10 L3
input impedance and output impedance for common gate amplifier.
OR
4 a. Develop an expression for drain to source voltage for a MOSFET 10 L3
amplifier using drain to gate feedback resistor.
b. Develop an expression for transconductance in terms of drain current and 4 L3
overdrive voltage.
c. With neat circuit diagram, develop an expression for voltage gain, input 6 L3
impedance and output impedance for common source amplifier without
source resistance.
MODULE-3
5 a. With neat circuit diagram, explain the operation of R-2R DAC 7 L2
b. For the circuit shown in Fig 5b, the input voltage is a sine wave with peak 7 L3
value of 10V. Determine the trip point. Also plot the input output
waveform

Fig 5b

c. With neat circuit diagram, explain the operation of Schmitt trigger. 6 L2


OR
6 a. With neat circuit diagram, internal diagram of 555 timer and 10 L3
waveforms explain the operation of astable multivibrator.
b. With neat circuit diagram, explain the operation of wein bridge 10 L3
oscillator
MODULE-4
7 a. Classify negative feedback amplifiers and explain each with neat 10 L3
block diagram.
b. Calculate the feedback fraction, ideal closed loop gain, percentage error 5 L3
and exact closed loop voltage gain. Use AOL = 100,000 for 741C

c. With neat circuit diagram and expressions, explain current 5 L3


amplifiers.
OR
8 a. Classify the filters and explain the ideal response for each of the 10 L3

Page 02 of 02
BEC303
filters.
b. With neat circuit diagrams, explain the operation of first order low pass 10 L3
filter and high pass filter
MODULE-5
9 a. With neat circuit diagram and waveform explain SCR phase control 10 L3
using RC circuit
b. With neat circuit diagram, explain the operation of UJT and hence 10 L3
explain how it is used as relaxation oscillator.
OR
10 Make use of break over characteristics to explain the operation of 4 10 L3
layer diode
Write short notes on IGBT 5 L3
Explain bi-directional thyristors in brief. 5 L3

Page 03 of 02

You might also like