190CW7

19 inch TFT WXGA LCD Colour Monitor Chassis: HUDSON7
190CW7CS/00
190CW7CS/27
190CW7CS/69
190CW7CS/75
190CW7CS/93
190CW7CS/96
190CW7CB/69
190CW7CB/93
190WV7CS/00
Horizontal frequencies
30 - 83 kHz
TABLE OF CONTENTS
Description Page Description Page
Important Safety Notice-----------------------------------2 Failure Mode Of Panel- ---------------------------------28
Technical Data----------------------------------------------3 Wiring Diagram------------------------------------------29
Installation---------------------------------------------------4 Block Diagram--------------------------------------------30
Troubleshooting--------------------------------------------5 Scaler Diagram&C.B.A. ---------------------------31~37
On Screen Display--------------------------------------6~7 Power Diagram & C.B.A. --------------------------38~41
Lock/unlock,Aging,Factory mode-----------------------8 Control Diagram&C.B.A. --------------------------42~43
Philips Pixel Defect Policy -------------------------------- 9 General product specification--------------------44~65
Mechanical Instructions ----------------------------10~11 Exploded View -------------------------------------------66
Color adjustment -----------------------------------------12 Repair tips--------------------------------------------67~68
FAQs (Frequently Asked Questions)-------------13~14 Repair Flow chart-----------------------------------69~71
Electrical instruction --------------------------------15~16 Safety Test Requirments-------------------------------72
DDC Instructions&Serial Number ----------------17~23 Spare/ Recommended P arts List-----------------73~77
DDC DATA --------------------------------------------24~25 Different Parts List----------------------------------78~83
Firmware Upgrade for CPU- -----------------------26~27 Revision List----------------------------------------------84
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC
EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING.
REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES
Published by BCU Monitors Printed in Suzhou Copyright reserved Subject to modification K Jul. 27 2006 GB 3138 106 10544
2 190CW7 LCD Important Safety Notice
Proper service and repair isimportant to the safe, reliable

FOR PRODUCTS CONTAINING LASER :
operation of all HPConsumer Electronics Company**
Equipment. The service procedures recommended by HP and DANGER- Invisible laser radiation when open.
described in this service manual are effective methods of AVOID DIRECT EXPOSURE TO BEAM.
performing service operations. Some ofthese service CAUTION- Use of controls or adjustments or
operations require the use of tools specially designed for the performance of procedures other than
purpose. The special tools should be used when and as those specified herein may result in
recommended. hazardous radiation exposure.
It is important to note that this manual contains various CAUTION- The use of optical instruments with this
CAUTIONS and NOTICES which should be carefully read in product will increase eye hazard.
order to minimize the risk of personal injury to service

personnel. The possibility exists that improper service
methods may damage the equipment. It is also important to
understand that these CAUTIONS and NOTICES ARE NOT TO ENSURE THE CONTINUED RELIABILITY OF THIS
EXHAUSTIVE. HP could not possibly know, evaluate and PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
advise the service trade of all conceivable ways in which REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART
service might be done or of the possible hazardous NUMBERS IN THE PARTS LIST SECTION OF THIS
consequences of each way. Consequently, HP has not SERVICE MANUAL.
undertaken any such broad evaluation. Accordingly, a
servicer who uses a service procedure or tool which is not
recommended by HP must first satisfy himself thoroughly that
neither his safety nor the safe operation of the equipment will
be jeopardized by the service method selected.
* * Hereafter throughout this manual, HP Consumer Take care during handling the LCD module with backlight
Electronics Company will bereferred to as HP. unit
- Must mount the moduleusing mounting holes arranged infour
WARNING
corners.
- Do not press onthe panel, edge of theframe strongly or electric
Critical components having special safety characteristics are
shock as this will result in damage to the screen.
identified with a bythe Ref. No. inthe parts list and
- Do not scratch orpress on the panel withany sharp objects, such
enclosed within a broken line*
as pencil or pen asthis may result in damage to the panel.
(where several critical components are grouped in one area)
- Protect the module fromthe ESD as it maydamage the electronic
along with the safety symbol on the schematics or
circuit (C-MOS).
exploded views.
- Make certain that treatment person s body are grounded through
Use of substitute replacement parts which do not have the
wrist band.
same specified safety characteristics may create shock, fire,
- Do not leave themodule in high temperature andin areas of high
or other hazards.
humidity for a long time.
Under no circumstances should the original design be
- Avoid contact with water as it may ashort circuit within the module.
modified or altered without written permission from Philips.
- If the surface ofpanel become dirty, please wipe it off with a soft
Philips assumes no liability, express or implied, arising out of
material. (Cleaning with a dirty or rough cloth may damage the
any unauthorized modification of design.
panel.)
Servicer assumes all liability.
* Broken Line
Technical Data 190CW7 LCD 3
LCD panel Input DVI-D connector pin
Type NR. : M190A1

Outside dimensions : 427.2(w)*277.4(h)*17.0(d) (Typ) mm
Pitch ( mm ) : 0.285 mm x 0.285 mm
Color pixel arrangement : RGB vertical stripes
Display surface : low reflection, antiglare with hard coating
Color depth : 16.2M colors (6 bits+FRC)
Pin No. Description
Backlight : CCFL edge light system
Active area(WxH) : 410.4 x 256.5mm (19.05" diagonal) 1 T.M.D.S. data2-
View angle (CR>10) : 75/75 (min), 85/85 (typ) for Horizontal & 70/ 2 T.M.D.S. data2+
70 (min), 80/80 (typ) for Vertical 3 T.M.D.S. data2 shield
Contrast ratio : 850:1(Typ.) 500:1(Min.) 4 No Connect
White luminance : Original color 230 nits (Min), 300 nits (Typ.)
5 No Connect
Response time : 5ms (typ)
Scanning frequencies 6 DDC clock
Hor. : 30 - 83 K Hz 7 DDC data
Ver. : 55 - 75Hz 8 No Connect
Video dot rate : <140 MHz 9 T.M.D.S. data1-
Power input : 90-264 V AC, 50/60 ± 2 Hz
10 T.M.D.S. data1+
Power consumption : < 36W(typ.) maximum
Ambient temperature : 0 °C - 35 °C 11 T.M.D.S. data1 shield
12 No Connect
Power input connection 13 No Connect
Power cord length : 1.8 M
14 +5V Power
Power cord type : 3 leads power cord with
protective earth plug. 15 Ground (for +5V) - Cable detect
Power management 16 Hot plug detect
The monitor must comply with the Microsoft On Now specification, with 17 T.M.D.S. data0-
two power management states, as defined by the VESA DPMS document. 18 T.M.D.S. data0+
The monitor must appropriately display the DPMS state.
19 T.M.D.S. data0 shield
20 No Connect
Mode HSYNC VSYNC Video Pwr-cons. Indication Rec.
21 No Connect
time 22 T.M.D.S clock shield
23 T.M.D.S. clock+
Power- On On active < 36 W(typ..) Green LED --
24 T.M.D.S. clock-
On 34 W (typ.)
Susceptibility of display to external environment
Off Off Off blanked <1W Amber LED < 3
Operating
s - Temperature : 0 to 40 degree C
- Humidity : 80% max
DC N/A <1W LED Off - Altitude : 0-3658m
- Air pressure : 600-1100 mBAR
Power Off
Storage
- Temperature : -20 to 60 degree C
Pin Assignment
- Altitude : 0-12192m
Pin No. Assignment Pin No. Assignment

1 Red video input 9 DDC +3.3V OR +5V
2 Green video input 10 GND
3 Blue video input 11 GND
4 GND 12 Serial data line (SDA)
5 Cable detect 13 H-sync
6 Red video GND 14 V-sync
7 Green video GND 15 Data clock line (SCL)
8 Blue video GND
4 190CW7 LCD Installation
Front View Accessory Pack

Item Description
Power cord
VGA signal cable
EDFU pack
Connecting to Your PC
1) Connect the power cord to the back of the monitor firmly.
1 To switch monitor's power On and Off
Notes:If you use an Apple Macintosh , you need to connect the

TM
2 MENU To access OSD menu / to confirm special Mac adapter to one end of the monitor signal cable.
3
To move the adjust
4
To adjust brightness of the display
5
To adjust contrast of the display
6 AUTO Automatically adjust the horizontal position,

vertical position, phase and clock setting
Rear View
2) Connect to PC
(a) Turn off your computer and unplug its power cable.
(b) Connect the monitor signal cable to the video connector on the
back of your computer.
(c) Plug the power cord of your computer and your monitor into a
nearby outlet.
(d) Turn on your computer and monitor. If the monitor displays an
image, installation is complete.
1 Kensington anti-thief lock

2 AC power input
3 DVI-D input
4 VGA input
Troubleshooting 190CW7 LCD 5
This page deals with problems that can be corrected by a user. If the problem still persists after you have tried thesesolutions, contact Philips
customer service representative.
Common Problems
Having this problem Check these items
No Picture 1.Make sure the power cord is plugged into the power outlet and into the back of the
(Power LED not lit) monitor.
2.First, ensure that the power button on the front of the monitor is in the OFF position,
then press it to the ON position.
No Picture 1.Make sure the computer is turned on.
(Power LED is amber or yellow) 2. Make sure the signal cable is properly connected to your computer.
3.Check to see if the monitor cable has bent pins.
4.The Energy Saving feature may be activated
Screen says 1. Make sure the monitor cable is properly connected to your computer. (Also refer
to the Quick Set-Up Guide).
ATTENTION 2.Check to see if the monitor cable has bent pins.
3. Make sure the computer is turned on.
CHECK CABLE CONNECTION
AUTO button not working properly 1.The Auto Function is designed for use on standard Macintosh or IBM-compatible
PCs running Microsoft Windows.
2. It may not work properly if using nonstandard PC or video card.
Imaging Problems
Display position is incorrect 1.Press the Auto button.

2. Adjust the image position using the Horizontal Position and/or Vertical
Position in OSD Main Controls.
Image vibrates on the screen Check that the signal cable is properly connected to the graphics board or PC.
Vertical flicker appears 1. Press the Auto button.

2. Eliminate the vertical bars using the More Settings of Phase/Clock in OSD Main
Controls.
Horizontal flicker appears 1. Press the Auto button.

2. Eliminate the vertical bars using the More Settings of Phase/Clock in OSD Main
Controls.
The screen is too bright or too dark Adjust the contrast and brightness on OSD Main Controls. (The backlight of the
LCD monitor has a fixed life span. When the screen becomes dark or begins to
flicker, please contact your dealer).
An after-image appears If an image remains on the screen for an extended period of time, it may be
imprinted in the screen and leave an afterimage. This usually disappears after a
few hours.
An after-image remains after the power This is characteristic of liquid crystal and is not caused by a malfunction or
has been turned off. deterioration of the liquid crystal. The after-image will disappear after a peroid
of time.
Green, red, blue, dark, and white dots The remaining dots are normal characteristic of the liquid crystal used in
Remains today's technology.
6 190CW7 LCD On Screen Display
Description of the On Screen Display
This is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance of the monitors directly through an
on-screen instruction window. The user interface provides userfriendliness and ease-of-use when operating the monitor.
Basic and simple instruction on the control keys.
When you press "menu" button on the front control of your monitor, the On-Screen Display (OSD) Main Controls window will pop up and
you can then start making adjustments to your monitor's various features. Use the keys to make your adjustments.
The OSD Tree
Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the
different adjustments later on.
On Screen Display 190CW7 LCD 7
8 190CW7 LCD Lock/Unlock,Aging,Factory Mode
Front Control After 15 seconds,

bring up:
ATTENTION
AGING...
----------
----------
repeatly
Connect Signal cable again=> go back to normal display
Access Factory Mode
1). Turn off monitor.

2). [Push "AUTO" & "MENU" buttons at the same time and hold them]
To Lock/Unlock OSD FUNCTION(User Mode) +[Press "power" button untill comes out "Windows screen" ]
The OSD function can be locked by pressing"OK"button(1) for more => then release all buttons
than 10 seconds, the screen shows following windows for 4 seconds. 3).Press "MENU" button, wait until the OSD menu with
Everytime when you press"OK" button, this message Characters "HUDSON 190CW7 V0.15 2006-06-26" (below OSD
appears on the screen automatically. menu) come on the Screen of the monitor.
ATTENTION SIGNAL
OSD MAIN CONTROLS

LOCKED
Unlock OSD function

Unlocked OSD function can be released by pressing "OK" button for
more than 10 seconds again.
ATTENTION SIGNAL
OSD MAIN CONTROLS

UNLOCKED
Factory Mode indicator
Access Aging Mode Factory Menu

Step 1 : Disconnect Interface Cable between Monitor and PC. Cursor can move on gray color area
Step 2 : Turn off LCD monitor.Then [Push "AUTO" & " MENU " buttons Hot key function: by pressing " LEFT " and " RIGHT " key
at the same time and hold them]+[Press power " " button untill comes Simultaneously at User Mode (or Factory Mode)
out " AGING screen"] => then release all buttons. (PS: The Offset R G B function can be used on reduce or eliminate
Bring up: snowy noise on the background when the resolution of video signal
is 1440*900 vertical 60Hz. Slightly increase or decrease the value
until snowy noise completely disappear.
ATTENTION
AGING...
After 15 seconds,
bring up: ATTENTION
AGING...
After 15 seconds,
bring up: ATTENTION
AGING...
Philips Pixel Defect Policy 190CW7 LCD 9
Philips' Flat Panel Monitors Pixel Defect Policy Black Dot Defects Black dot defects appear as pixels or sub
pixels that are always dark or 'off'. These are the types of black
Philips strives to deliver the highest quality products. We dot defects:
use some of the industry's most advanced manufacturing
processes and practice stringent quality control. However,
pixel or sub pixel defects on the TFT LCD panels used in
flat panel monitors are sometimes unavoidable. No
manufacturer can guarantee that all panels will be free
from pixel defects, but Philips guarantees that any monitor
with an unacceptable number of defects will be repaired or
replaced under warranty. This notice explains the different
types of pixel defects and defines acceptable defect levels
for each type. In order to qualify for repair or replacement
under warranty, the number of pixel defects on a TFT LCD
panel must exceed these acceptable levels. For example,
One dark sub pixel Two or three adjacent dark sub pixels
no more than 0.0004% of the sub pixels on a 15" XGA
monitor may be defective. Furthermore, Philips sets even
higher quality standards for certain types or combinations Proximity of Pixel Defects
of pixel defects that are more noticeable than others. This
policy is valid worldwide. Because pixel and sub pixels defects of the same type that are
near to one another may be more noticeable, Philips also specifies
tolerances for the proximity of pixel defects.
Pixel Defect Tolerances
In order to qualify for repair or replacement due to pixel defects

during the warranty period, a TFT LCD panel in a Philips flat panel
monitor must have pixel or sub pixel defects exceeding the
tolerances listed in the following tables.
BRIGHT DOT DEFECTS ACCEPTABLE LEVEL
MODEL 190CW7
Pixels and Sub pixels 1 lit subpixel 3 or fewer
A pixel, or picture element, is composed of three sub pixels 2 adjacent lit subpixels 1 or fewer
in the primary colors of red, green and blue. Many pixels
3 adjacent lit subpixels (one white
together form an image. When all sub pixels of a pixel are lit, 0
pixel)
the three colored sub pixels together appear as a single
white pixel. When all are dark, the three colored sub pixels Distance between two bright dot
together appear as a single black pixel. Other combinations defects*
25mm or more
of lit and dark sub pixels appear as single pixels of other
colors. 3 or fewer
Total bright dot defects of all types
Types of Pixel Defects BLACK DOT DEFECTS ACCEPTABLE LEVEL
Pixel and sub pixel defects appear on the screen in different MODEL 190CW7
ways. There are two categories of pixel defects and several
types of sub pixel defects within each category. Bright dot 1 dark subpixel 5 or fewer
defects appear as pixels or sub pixels that are always lit or
2 adjacent dark subpixels 2 or fewer
'on'. These are the types of bright dot defects:
3 adjacent dark subpixels(one white pixel) 0
Distance between two black dot defects* 15 mm or more
Total black dot defects of all types 5 or fewer
TOTAL DOT DEFECTS ACCEPTABLE LEVEL

Two adjacent lit
One lit red, Three adjacent lit MODEL 190CW7
sub pixels:
green or - Red + Blue = Purple
sub pixels
blue sub pixel - Red + Green = Yellow (one white pixel) Total bright or black dot defects of all types 5 or fewer
- Green + Blue = Cyan
(Light Blue)
Note:
* 1 or 2 adjacent sub pixel defects = 1 dot defect
10 190CW7 LCD Mechanical Instruction
Front view 2: Remove the Back Cover Assy

a. Unscrew 1 screws as shown in Fig.6.
b. Open 10 clicks on right and left side as shown in Fig.7 and Fig.8.
c. Open 7 clicks on bottom side as shown in Fig.9.
d. Open 7 clicks on top side as shown in Fig.10.
e. Remove the BACK COVER ASSY in Fig.11.
Fig.1
Fig.6
Back view
Fig.7
Fig.2
1. Remove the base.
a: Place the monitor face down on a smooth surface as Fig.3.

Be carefully to prevent the scratch and injury during the
uninstallation. Press the botton and push the base as Fig.3.
Base
Botton
Fig.8
Fig.3
b: Drag the click to left and slip the stand bottom to left at the same time
as Fig.4.
Fig.9
Fig.4
c: Remove the three screws and remove the hinge and stand top as
Fig.5.
Fig.10
Fig.5
Fig.11
Mechanical Instruction 190CW7 LCD 11
3. Remove the Key board and bezel.

a. Unscrew the 2 screws and disconnect the 1 cable to remove the
Key board as Fig.11.
b. Unscrew the 2 screws to remove the bezel as Fig. 12.
Fig. 18
Fig.12
4. Remove the SHIELDING ASSY , Scaler , Power board.

a. Unscrew the 4 screws on left and right side as Fig.13~14.
b. Disconnect the 1 cable carefully and turn the SHIELDING ASSY to
right as Fig.15~16.
c. Unscrew the 14 screws to remove the SHIELDING ASSY as
Fig. 17~18. Fig. 19
d. Disconnect the 4 cables to remove the Scaler and Power board.
Fig. 20
Fig.13
In warranty, it is not allowed to disassembly the LCD panel, even the
backlight unit defect.
Out of warranty, the replacment of backlight unit is a correct way
when the defect is cused by backlight (CCFL,Lamp).
Fig.14
Fig.15
Fig. 16
Fig. 17
12 190CW7 LCD Color Adjustment
Alignment procedure Clear image

1. Turn on the LCD monitor.
2.Turn on the Timing/pattern generator. See Fig.1
3. Preset LCD color Analyzer CA-110
-Remove the lens protective cover of probe CA-A30.
-Set measuring/viewing selector to measuring position for reset
analyzer.(zero calibration) as Fig.2
- Turn on the color analyzer (CA-110) Measurement/viewing selector
-Press 0-CAL button to starting reset analyzer.
Fig.5
5.Display
Press "LEFT" or "RIGHT" button to select . Change the value
by "LEFT" or "RIGHT" key until the X,Y co-ordinates as below
5.1 White color adjustment

Cover (black)
There are three factory preset white color 9300K, 6500K, sRGB.
Apply full white pattern, with brightness in 100 % position
and the contrast control at 50 % position.
Measurement viewing selector The 1931 CIE Chromaticity (color triangle) diagram (x,y)
Fig. 2 coordinate for the screen center should be:
Fig. 1
Product spec.
9300K CIE coordinates X = 0.283 ± 0.02
4. Access Factory Mode Y = 0.297 ± 0.02
1). Turn off monitor. 6500K/ sRGB CIE coordinates X = 0.313 ± 0.02
2). [Push "AUTO" & "MENU" buttons at the same time and hold them] Y = 0.329 ± 0.02
+[Press "power" button untill comes out "Windows screen" ]
=> then release all buttons sRGB CIE coordinates X = 0.313 ± 0.02
3).Press "MENU " button, wait until the OSD menu with Y = 0.329 ± 0.02
Characters" HUDSON 190CW7 V0.15 2006-06-26" (below OSD Production alignment spec.
menu) come on the Screen of the monitor. as shown in Fig3.
Y = 0.297 ± 0.005
6500K/ sRGB CIE coordinates X = 0.313 ± 0.005

Y = 0.329 ± 0.005
sRGB CIE coordinates X = 0.313 ± 0.005

Y = 0.329 ± 0.005
Quality Inspection spec.

Y = 0.297 ± 0.015

Y = 0.329 ± 0.015
Factory Mode indicator sRGB CIE coordinates X = 0.313 ± 0.015

Y = 0.329 ± 0.015
Fig. 3
4). Press "MENU" button, then select factory mode indicator by"LEFT"
or "RIGHT" button .Press"MENU" button to bring up submenu
windows as below:
Fig. 4
FAQs (Frequently Asked Questions) 190CW7 LCD 13
General FAQs
Q: When I install my monitor what should I do if the screen shows 'Cannot display this video
mode'?
A: Recommended video mode for Philips 19 " : 1440 x 900 @60Hz.
1. Unplug all cables, then connect your PC to the monitor that you used previously.
2. In the Windows Start Menu, select Settings/Control Panel. In the Control Panel Window, select the Display icon. Inside the Display Control Panel,
select the 'Settings' tab. Under the setting tab, in box labeled 'desktop area', move the slidebar to 1440 x 900 pixels (19").
3. Open 'Advanced Properties' and set the Refresh Rate to 60Hz, then click OK.
4. Restart your computer and repeat step 2 and 3 to verify that your PC is set at 1440 x 900@60Hz (19").
5. Shut down your computer, disconnect your old monitor and reconnect your Philips LCD monitor.
6. Turn on your monitor and then turn on your PC.
Q: What does 'refresh rate' mean in connection with an LCD monitor?

A: The refresh rate is of much less relevance for LCD monitors. LCD monitors display a stable, flicker-free image at 60Hz. There is no visible
difference between 85Hz and 60Hz
Q: What are the .inf and .icm files on the CD-ROM? How do I install the drivers (.inf and . icm)?
A: These are the driver files for your monitor. Follow the instructions in your user manual to install the drivers. Your computer may ask you for monitor
drivers (.inf and . icm files) or a driver disk when you first install your monitor. Follow the instructions to insert the ( companion CD-ROM) included in
this package. Monitor drivers (.inf and . icm files) will be installed automatically.
Q: How do I adjust the resolution?

A: Your video card/graphic driver and monitor together determine the available resolutions. You can select the desired resolution under Windows®
Control Panel with the "Display properties".
Q: What if I get lost when I am making monitor adjustments?

A: Simply press the MENU button, then select 'Reset' to recall all of the original factory settings.
Q: What is the Auto function?

A: The AUTO adjustment key restores the optimal screen position, phase and clock settings by pressing of a single button – without the need to
navigate through OSD (On Screen Display) menus and control keys.
Note: Auto function is available in selected models only.
Q: My Monitor has no power (Power LED does not light up). What should I do?
A: Make sure the AC power cord is connected between the monitor and AC outlet, and click a key on keyboard/mouse to wake up the PC.
Q: Will the LCD monitor accept an interlaced signal under PC models?

A: No. If an Interlace signal is used, the screen displays both odd and even horizontal scanning lines at the same time, thus distorting the picture.
Q: What does the Refresh Rate mean for LCD?

A: Unlike CRT display technology, in which the speed of the electron beam is swept from the top to the bottom of the screen determines flicker, an
active matrix display uses an active element (TFT) to control each individual pixel and the refresh rate is therefore not really applicable to LCD
technology.
Q: Will the LCD screen be resistant to scratches?

A: A protective coating is applied to the surface of the LCD, which is durable to a certain extent (approximately up to the hardness of a 2H pencil). In
general, it is recommended that the panel surface is not subject to any excessive shocks or scratches.
Q: How should I clean the LCD surface?

A: For normal cleaning, use a clean, soft cloth. For extensive cleaning, please use isopropyl alcohol. Do not use other solvents such as ethyl alcohol,
ethanol, acetone,hexane, etc.
Q:Can I change the color setting of my monitor?

A:Yes, you can change your color setting through OSD control as the following procedures,
1. Press "MENU" to show the OSD (On Screen Display) menu.
2. Press "Left Arrow" to select the option "color" then press "MENU" to enter color setting, there are five settings as below.
a. 6500K; this setting features the panel closed to red-white color tone.
b. 9300K; this setting features the panel closed to blue-white color tone.
c. Original; this setting load the default panel setting in terms of color tone. (Note: different panel maker may feature a different color temperature*)
d. User Define; the user can choose his/her preference color setting by adjusting red, green, blue color.
e. sRGB; this is a standard setting for ensuring correct exchange of colors between different device (e.g. digital cameras, monitors, printers,
scanners, etc.)
Q: Can the Philips LCD Monitor be mounted on the wall?

A: Yes. Philips LCD monitors have this optional feature. For standard VESA mount holes on the rear cover allows the user to mount the Philips
monitor on most of the VESA standard arms or accessories. We recommend to contact your Philips sales representative for more information.
Screen Adjustments
Q: What is the FPadjust program on the CD-ROM?

A: The FPadjust program generates alignment patterns that help you adjust monitor settings such as Contrast, Brightness, Horizontal Position,
Vertical Position, Phase and Clock for optimal performance.
Q: When I install my monitor, how do I get the best performance from the monitor?
A:1. For best performance, make sure your display settings are set at 1440 x 900@60Hz for 19". Note: You can check the current display settings
by pressing the OSD MENU button once. The current display mode is shown in OSD first page.
14 190CW7 LCD FAQs (Frequently Asked Questions)
2. To install the Flat Panel Adjust (FPadjust) program located on the monitor setup CD-ROM, open the CD-ROM and double-click the FP_setup4.3.exe icon.
This will install FP Adjust automatically and place a shortcut on your desktop.
3. Run FPadjust by double clicking the shortcut. Follow the instructions step by step to optimize image performance with your system's video controller.
Q: How do LCDs compare to CRTs in terms of radiation?

A: Because LCDs do not use an electron gun, they do not generate the same amount of radiation at the screen surface.
Compatibility with other Peripherals
Q: Are Philips LCD monitors Plug-and-Play?

A: Yes, the monitors are Plug-and-Play compatible with Windows 95, 98, 2000 and XP.
Q: What is USB (Universal Serial Bus)?

A: Think of USB as a smart plug for PC peripherals. USB automatically determines resources (like driver software and bus bandwidth) required by peripherals.
USB makes necessary resources available without user intervention. There are three main benefits of USB. USB eliminates "case anxiety," the fear of
removing the computer case to install circuit board cards -- that often requires adjustment of complicated IRQ settings -- for add-on peripherals. USB does
away with "port gridlock." Without USB,PCs are normally limited to one printer, two Com port devices (usually a mouse and modem), one Enhanced Parallel
Port add-on (scanner or video camera, for example), and a joystick. More and more peripherals for multimedia computers come on the market every day.
With USB, up to 127 devices can run simultaneously on one computer. USB permits "hot plug-in." No need to shut down, plug in, reboot and run set up to
install peripherals. No need to go through the reverse process to unplug a device. Bottom line: USB transforms today's "Plug-and-Pray" into true
Plug-and-Play! Please refer to glossary for more information about USB.
Q: What is a USB hub ?

A: A USB hub provides additional connections to the Universal Serial Bus. A hub's upstream port connects a hub to the host, usually a PC. Multiple
downstream ports in a hub allows connection to another hub or device, such as a USB keyboard, camera or printer.
LCD Panel Technology

Q: What is a Liquid Crystal Display?
A: A Liquid Crystal Display (LCD) is an optical device that is commonly used to display ASCII characters and images on digital items such as watches,
calculators, portable game consoles, etc. LCD is the technology used for displays in notebooks and other small computers. Like light-emitting diode and
gas-plasma technologies, LCD allows displays to be much thinner than cathode ray tube(CRT) technology.LCD consumes much less power than LED and
gas-displays because it works on the principle of blocking light rather than emitting it.
Q: What differentiates passive matrix LCDs from active matrix LCDs?

A: An LCD is made with either a passive matrix or an active matrix display grid. An active matrix has a transistor located at each pixel intersection, requiring
less current to control the luminance of a pixel. For this reason, the current in an active matrix display can be switched on and off more frequently, improving
the screen refresh time (your mouse pointer will appear to move more smoothly across the screen, for example). The passive matrix LCD has a grid of
conductors with pixels located at each intersection in the grid.
Q: What are the advantages of TFT LCD compared with CRT?

A: In a CRT monitor, a gun shoots electrons and general light by colliding polarized electrons on fluorescent glass. Therefore, CRT monitors basically operate
with an analog RGB signal. A TFT LCD monitor is a device that displays an input image by operating a liquid crystal panel. The TFT has a fundamentally
different structure than a CRT: Each cell has an active matrix structure and independent active elements. A TFT LCD has two glass panels and the space
between them is filled with liquid crystal. When each cell is connected with electrodes and impressed with voltage, the molecular structure of the liquid
crystal is altered and controls the amount of inlet lighting to display images. A TFT LCD has several advantages over a CRT, since it can be very thin and no
flickering occurs because it does not use the scanning method.
Q: Why is vertical frequency of 60Hz optimal for an LCD monitor?

A: Unlike a CDT monitor, the TFT LCD panel has a fixed resolution. For example, an XGA monitor has 1024x3 (R, G, B) x 768 pixels and a higher resolution
may not be available without additional software processing. The panel is designed to optimize the display for a 65MHz dot clock, one of the standards for
XGA displays. Since the
Q: What kind of wide-angle technology is available? How does it work?

A: The TFT LCD panel is an element that controls/displays the inlet of a backlight using the dual-refraction of a liquid crystal. Using the property that the
projection of inlet light refracts toward the major axis of the liquid element, it controls the direction of inlet light and displays it. Since the refraction ratio of
inlet light on liquid crystal varies with the inlet angle of the light, the viewing angle of a TFT is much narrower than that of a CDT. Usually, the viewing angle
refers to the point where the contrast ration is 10. Many ways to widen the viewing angle are currently being developed and the most common approach is to
use a wide viewing angle film, which widens the viewing angle by varying the refraction ratio. IPS (In Plane Switching) or MVA (Multi Vertical Aligned) is
also used to give a wider viewing angle.
Q: Why is there no flicker on an LCD Monitor?

A: Technically speaking, LCDs do flicker, but the cause of the phenomenon is different from that of a CRT monitor -- and it has no impact of the ease of
viewing. Flickering in an LCD monitor relates to usually undetectable luminance caused by the difference between positive and negative voltage. On
the other hand, CRT flickering that can irritate the human eye occurs when the on/off action of the fluorescent object becomes visible. Since the reaction
speed of liquid crystal in an LCD panel is much slower, this troublesome form of flickering is not present in an LCD display.
Q: Why is an LCD monitor virtually low of Electro Magnetic Interference?

A: Unlike a CRT, an LCD monitor does not have key parts that generate Electro Magnetic Interference, especially magnetic fields. Also, since an LCD
display utilizes relatively low power, its power supply is extremely quiet.
Ergonomics, Ecology and Safety Standards
Q: What is the CE mark?

A: The CE (Conformite Europeenne) mark is required to be displayed on all regulated products offered for sale on the European market. This 'CE' mark
means that a product complies with the relevant European Directive. A European Directive is a European 'Law' that relates to health, safety, environment
and consumer protection, much the same as the U.S. National Electrical Code and UL Standards.
Q: Does the LCD monitor conform to general safety standards?

A: Yes. Philips LCD monitors conform to the guidelines of MPR-II and TCO 99/03 standards for the control of radiation, electromagnetic waves, energy
reduction, electrical safety in the work environment and recyclability. The specification page provides detailed data on safety standards.
Electrical Instructions 190CW7 LCD 15
1 Electrical characteristics
1.1 Interface signals
1). D-Sub Analog

Input signal : Video, Hsync., Vsync
Video : 0.7 Vp-p, input impedance, 75 ohm @DC
Sync. : Separate sync TTL level , input impedance 2.2k ohm terminate
Hsync Positive/Negative
Vsync Positive/Negative
Composite sync TTL level, input impedance 2.2k ohm terminate(Positive/Negative)
Sync on green video 0.3 Vp-p Negative (Video 0.7 Vp-p Positive)
2). Intel DVI Digital
Input signal : Four channel TMDS signal
1.2 Interface
1.2.1 D-Sub Cable

Length : 1.8 M +/- 50 mm (fixed) , fix in monitor and with transplant pin protect cover.
Connector type : D-Sub male with DDC2B pin assignments.
Blue connector thumb-operated jack screws
1.3 Timing requirement
1.3.1 Mode storing capacity
Factory preset modes : 17

Preset modes : 40
User define modes : 24
Note: 1. Screen displays perfect picture at 17 factory-preset modes.
1.3.2Factory preset modes (17 modes)
Item H.Freq. Mode Resolution V.Freq. Item H.Freq. Mode Resolution V.Freq.
1 31.469 DOS 720x400 70.087 11 60.023 VESA 1024x768 75.029
2 31.469 VESA 640x480 59.940 12 67.500 VESA 1152x864 75.000
3 37.861 VESA 640x480 72.809 13 47.712 VESA 1360x768 60.015
4 37.500 VESA 640x480 75.000 14 55.935 VESA 1440x900 59.887
5 35.156 VESA 800x600 56.250 15 70.635 VESA 1440x900 74.984
6 37.879 VESA 800x600 60.317 16 35.000 MACINTOSH 640x480 67.000
8 46.875 VESA 800x600 75.000 18
9 48.363 VESA 1024x768 60.004 19
10 56.476 VESA 1024x768 70.069 20

16 190CW7 LCD Electrical Instructions
2 White color adjustment
There are three factory preset white color 9300K, 6500K, sRGB. Apply full white pattern, with brightness in 100 % position
and the contrast control at 50 % position. The 1931 CIE Chromaticity (color triangle) diagram (x,y) coordinate for the screen center
should be:
Product spec.
Y = 0.297 ± 0.02

Y = 0.329 ± 0.02

Y = 0.329 ± 0.02
Production alignment spec.

Y = 0.297 ± 0.005

Y = 0.329 ± 0.005

Y = 0.329 ± 0.005

Y = 0.297 ± 0.015

Y = 0.329 ± 0.015

Y = 0.329 ± 0.015
DDC Instructions 190CW7 LCD 17
Note: The alignment box has already build-in a batteries socket for
General using batteries (8~12V) as power source. Pull out the socket by
DDC Data Re-programming remove four screws at the rear of box. Please do not forget that
In case the DDC data memory IC or main EEPROM which storage all remove batteries after programming. The energy of batteries can
factory settings were replaced due to a defect, the serial numbers have only drive circuits for a short period of time.
to be re-programmed "Analog DDC IC, Digital DDC IC & EEPROM".
It is advised to re-soldered DDC IC and main EEPROM from the old
board onto the new board if circuit board have been replaced, in this case To Printer port
the DDC data does not need to be re-programmed.
DC 8~12V
Additional information To Monitor

Additional information about DDC (Display Data Channel) may be D-sub/DVI cable
obtained from Video Electronics Standards Association (VESA).
Extended Display Identification Data(EDID) information may be also
Power
obtained from VESA. indicator
System and equipment requirements

1. An i486 (or above) personal computer or compatible.
2. Microsoft operation system Windows 95/98 .
You have to Install the EDID_PORT_Tool under Win2000/XP . As Fig. 3
Fig. 1 .
Fig. 1
Pin assignment
A. 15-pin D-Sub Connector
PIN No. SIGNAL

1 Red video input
2 Green video input / sync on green
3 Blue video input
4 GND
5 GND - Cable detect
6 Red video GND
7 Green video GND
8 Blue video GND
9 DDC +3.3V or +5V
10 Logic GND
A. Cody the "UserPort.sys" to C:\WINNT\system32\drivers(win2000) 11 GND
12 Serial data line (SDA)
C:\WINDOWS\system32\drivers(winXP) 13 H-sync / H+V

14 V-sync
15 Data clock line (SCL)
B. Running " io.exe" everytime, Before you start to programming
edid data . B. Input DVI -D Connector pin
3. EDID46.EXE program
4. A/D Alignment kits (12NC: 3138 106 10396):

inclusion : a. Alignment box x1 (Fig. 2)
Pin No. Description
1 T.M.D.S. data2-
2 T.M.D.S. data2+
4 No Connect
5 No Connect
6 DDC clock
7 DDC data
8 No Connect
9 T.M.D.S. data1-
Fig. 2 10 T.M.D.S. data1+
12 No Connect
13 No Connect
14 +5V Power
15 Ground (for +5V) - Cable detect
16 Hot plug detect
17 T.M.D.S. data0-
18 T.M.D.S. data0+
b. Printer cable x1 19 T.M.D.S. data0 shield
c. (D-Sub) to (D-Sub) cable x1 20 No Connect
D. (D-Sub) to (DVI) cable x1 21 No Connect
22 T.M.D.S clock shield
23 T.M.D.S. clock+
24 T.M.D.S. clock-
18 190CW7 LCD DDC Instructions
Configuration and procedure 3. At the submenu, type the letter of your computer's hard disk drive
followed by :EDID46 (for example, C:\EDID46, as shown in Fig. 6).
There is no Hardware DDC (DDC IC) anymore. Main EEPROM stores
all factory settings and DDC data (EDID code) which is also called
Software DDC. The following section describes the connection and
procedure for Software DDC application. The main EEPROM can be re-
programmed by enabling '' factory memory data write'' function on the
DDC program (EDID46.EXE).
Initialize alignment box

1
In order to avoid that monitor entering power saving mode due
to sync will cut off by alignment box, it is necessary to initialize
alignment box before running programming software
(EDID46.EXE). Following steps show you the procedures and Fig. 6
connection.
4. Click OK button. The main menu appears (as shown in Fig. 7).
Step 1: Supply 8-12V DC power source to the Alignment box by This is for initialize alignment box.
plugging a DC power cord .
Step 2: Connecting printer cable and D-Sub cable of monitor as Fig. 4
1=Power connector
PC 2=D-SUB connector
To printer port (LTP1)
DC Power
8-12 V
----->
----->
1 2
To
Monitor
Printer
Port Fig. 7
To PC Fig. 4
Note 1: If the connection is improper, you will see the following error
message (as shown in Fig. 8) before entering the main menu.
Step 3: Installation of EDID46.EXE
Meanwhile, the (read EDID) function will be disable. At this
time, please make sure all cables are connected correctly and
Method 1: Start on DDC program fixedly, and the procedure has been performed properly.
Start Microsoft Windows.
1. The Program"EDID46.EXE" in service manual cd-rom be copyed to C:\ .
2. Click , choose Run at start menu of Windows as shown
In Fig. 5.
Fig. 8
Note 2: During the loading, EDID46 will verify the EDID data which just
loaded from monitor before proceed any further function, once
the data structure of EDID can not be recognized, the following
error message will appear on the screen as below. Please
confirm following steps to avoid this message.
Fig. 5
1. The data structure of EDID was incorrect.
2. DDC IC that you are trying to load data is empty.
3. Wrong communication channel has set at configuration setup
windows.
4. Cables loosed or poor contact of connection.
Fig. 9
Re-programming Analog DDC IC
Step 1: After initialize alignment box, connecting all

cables and box as shown in Fig. 10.
1=Power connector
PC 2=D-SUB connector
Fig. 13
DC Power
----->
----->
8-12V
1 2
To
Printer
Monitor Step 3: Modify DDC data (verify EDID version, week,
Port
Fig. 10 year)
To PC
Click (new function) icon from the tool bar, bring up

Step 1 of 9 as shown in Fig. 14 .
To PC Video port (D-sub)
EDID46 DDC application provides the function selection and
Step 2: Read DDC data from monitor
1. Click icon as shown in Fig. 11 from the tool bar to bring up
the Channels "Configuration Setup" windows as shown in Fig. 11.
=====>
Click this button
Fig. 11
Select and fill out,

If necessary.
Fig. 14
2. Select the DDC2Bi as the communication channel.
As shown in Fig. 12.
Step 4: Modify DDC data (Monitor Serial No.)

1. Click Next , bring up Fig. 15.
Fig. 12
Fig. 15
3. Click OK button to confirm your selection.

4. Click icon (Read EDID function) to read DDC EDID data from
monitor. The EDID codes will display on screen as shown in Fig. 13.
2. Click Next , bring up Fig.16.

Fig. 19
Fig. 16

3. Click Next , bring up Fig.17. In this step, please confirm the Descriptor Data Type is
Monitor Range Limits, and all the items are same as below.
Fig. 17
Fig. 20

Fig. 18 Fig. 21
8. Click Next , bring up Fig. 22. Step 8: Modify serial number in OSD
- Click Finish to exit the Step window. 1. Unzip the serial number.zip to your computer, then open the folder
- Serial number can be filled up at this moment (for example, TY as shown in Fig.27.
123456). 2. If use Win98 OS, you can execute SN.exe directly.
If use Win2000 or XP OS, first, you must execute install.bat, then
NOTE: You must modify the Serial NO. In step 9, otherwise the Serial execute SN.exe
NO. In OSD Couldn't be modified correctly. 3. Set I2C bus(press the left-top button of operating window) as shown
in Fig.28, then press " SET" button.
Step 5: Write DDC data 4. Set Block2 as shown in Fig.29
1. Configuration should be as Fig. 23. And press OK. 5. key in new serial number, then press " Write" button as shown in
Fig.29 , Click " WRITE" button.
6. It will appear "Serial Number Write OK" , Click "Enter" to finish it.
Fig. 22 Fig. 23
2. Access Factory Mode Fig.27

=> then release all buttons
3).Press "MENU" button, wait until the OSD menu with Characters
"HUDSON 190CW7 V0.15 2006-06-26" (below OSD menu) come
on the Screen of the monitor. as shown in Fig24.
Fig.28
TY 123456
Fig. 24
Factory Mode indicator Fig.29

3) Push "Menu" to exit OSD menu.
Step9:
4). Click (Write EDID) icon from the tool bar to write DDC data. 1. Disconnect the monitor power cord and connect it again.
Then wait for 20-30 seconds ,DDC data will be finished Writing. 2. Press the OK button to bring up the OSD main manu.
3. Re-confirm the serial Number is updated as shown in Fig.30.
Step 6: Save DDC data
Sometimes, you may need to save DDC data as a text file for
using in other IC chip. To save DDC data, follow the steps below:
1. Click (Save) icon (or click "file"-> "save as") from the tool bar
and give a file name as shown in Fig. 25.
The file type is EDID46 file (*.ddc) which can be open in WordPad.
By using WordPad, the texts of DDC data & table (128 bytes, hex
code) can be modified. If DDC TEXTS & HEX Table ar completely TY 123456
correct, it can be saved as .ddc flie to re-load it into DDC IC for DDC
Data application.
Fig.30
Fig. 25
Fig. 26
2. Click Save.
Step 7: Exit DDC program
Pull down the File menu and select Exit as shown in Fig. 26.
Re-programming Digital DDC IC
Step 1: After initialize alignment box, connecting all

cables and box as shown in Fig. 31.
PC 1=DVI-D connector
2=D-sub connector
3=Power Plug
Select and fill out,

If necessary.
To video card
DC Power Fig. 35 Fig. 36

8~12V
3
Step 4: Modify DDC data (Monitor Serial No.)
D-sub to DVI-D cable 1. Click Next , bring up Fig. 36.
To 1 2
Monitor 2. Click Next , bring up Fig. 37.
Printer
Port 3. Click Next , bring up Fig. 38.
D-sub cable
Step 2: Read DDC data from monitor Fig. 31
1. Click icon as shown in Fig. 11 from the tool bar to bring up

the Channels "Configuration Setup" windows as shown in Fig. 32.
=====>
Click this button
Fig. 37 Fig. 38
Fig. 32 4. Click Next , bring up Fig. 39.

2. Select the DDC2Bi as the communication channel.

As shown in Fig. 33.
Fig. 39 Fig. 40

In this step, please confirm the Descriptor Data Type is
Fig. 33 Fig. 34 Monitor Range Limits, and all the items are same as below.
3. Click OK button to confirm your selection.
4. Click icon (Read EDID function) to read DDC EDID data from
monitor. The EDID codes will display on screen as shown in Fig. 34. Philips 190CW
Step 3: Modify DDC data (verify EDID version, week,

year)
Click (new function) icon from the tool bar, bring up

Step 1 of 9 as shown in Fig. 35 .
EDID46 DDC application provides the function selection and
text change (select & fill out) from Step 1 to Step 9.
Fig. 41 Fig. 42
8. Click Next , bring up Fig. 43. 2. Click Save.

- Click Finish to exit the Step window.
- Serial number can be filled up at this moment (for example, TY Step 7: Exit DDC program
123456).
NOTE: You must modify the Serial NO. In step 9, otherwise the Serial Pull down the File menu and select Exit as shown in Fig. 47.
NO. In OSD Couldn't be modified correctly.
Fig. 43 Fig. 44
Fig. 47
Step 5: Write DDC data
1. Configuration should be as Fig. 40. And press OK.
Step 8: Turn off the monitor, exit the factory mode.
2. Access Factory Mode
=> then release all buttons
3).Press "MENU" button, wait until the OSD menu with Characters
"HUDSON 190CW7 V0.15 2006-06-26" (below OSD menu) come
on the Screen of the monitor. as shown in Fig24.
Serial Number Definition
BOM Code
Panel Supplier CODE
TY 123456
AUO 1
CPT 2
LPL(LG) 3
QDI 4
Factory Mode indicator CMO 5
Fig. 45
3) Push "Menu" to exit OSD menu. BZ1A0625000001
3. Click (Write EDID) icon from the tool bar to write DDC data. SERIAL NO
Then wait for 20-30 seconds ,DDC data will be finished Writing.
YEAR/WEEK
Step 6: Save DDC data
Sometimes, you may need to save DDC data as a text file for using SERVICE VERSION CHANGE CODE
in other IC chip. To save DDC data, follow the steps below:
1. Click (Save) icon (or click "file"-> "save as") from the tool bar and BOM CODE(BILL OF MATERIAL)CODE
give a file name as shown in Fig. 46.
The file type is EDID46 file (*.ddc) which can be open in WordPad. By SITE CODE(PRODUCTION CENTER)
using WordPad, the texts of DDC data & table (128 bytes, hex BZ CODE(AR-CZECH REPUBLIC
code) can be modified. If DDC TEXTS & HEX Table ar completely VN-HUNGARY(SZR),BZ-SUZHOU
correct, it can be saved as *.ddc flie to re-load it into DDC IC for DDC DS-DONGGUAN)
Data application.
Fig.46
24 190CW7 LCD DDC DATA
THE DISPLAY DATA CHANNEL (DDC_2B) CONTENT INCLUDING: Standard Timing Identification #3
(FOR 190CW7 ANALOG FOR CMO PANEL) Horizontal active pixels : 1440
Aspect Ratio : 16:10
********************************************************************** Refresh Rate : 60
EDID log file
********************************************************************** Standard Timing Identification #4
Vendor/Product Identification Horizontal active pixels : 1440
ID Manufacturer Name : PHL
Aspect Ratio : 16:10
ID Product Code : 084A (HEX.)
Refresh Rate : 75
ID Serial Number : 36F02 (HEX.)
Week of Manufacture : 27
Year of Manufacture : 2006 Detailed Timing #1
Pixel Clock (MHz) : 106.5
EDID Version, Revision H Active (pixels) : 1440
Version : 1 H Blanking (pixels) : 464
Revision : 3 V Active (lines) : 900
V Blanking (lines) : 34
Basic Display Parameters/Features H Sync Offset (F Porch) (pixels): 80
Video Input Definition : Analog Video Input H Sync Pulse Width (pixels) : 152
0.700V/0.300V (1.00Vpp) V Sync Offset (F Porch) (lines) : 3
without Blank-to-Black Setup V Sync Pulse Width (lines) : 6
Separate Sync H Image Size (mm) : 408
Composite Sync V Image Size (mm) : 255
Sync on Green H Border (pixels) : 0
no Serration required V Border (lines) : 0
Flags : Non-interlaced
Maximum H Image Size : 40 : Normal Display, No stereo
Maximum V Image Size : 25 : Digital Separate sync.
: Positive Vertical Sync.
Display Transfer Characteristic : 2.2
: Negative Horizontal Sync.
(gamma)
Feature Support (DPMS) : no Standby Monitor Descriptor #2

no Suspend Monitor Range Limits
Active Off Min. Vt rate Hz : 55
Max. Vt rate Hz : 75
Display Type : RGB color display Min. Horiz. rate kHz : 30
Preferred Timing Mode : Detailed timing block 1 Max. Horiz. rate kHz : 83
Max. Supported Pixel : 140
Color Characteristics
Red X coordinate : 0.64 No secondary GTF timing formula supported.
Red Y coordinate : 0.334
Green X coordinate : 0.285 Monitor Descriptor #3
Green Y coordinate : 0.599 Monitor Name : Philips 190CW
Blue X coordinate : 0.153
Blue Y coordinate : 0.076 Monitor Descriptor #4
White X coordinate : 0.313 Serial Number : TY 12345
White Y coordinate : 0.328
Extension Flag : 0
Established Timings
Established Timings I : 720 x 400 @70Hz (IBM,VGA)
Check sum : 6A (HEX.)
640 x 480 @60Hz (IBM,VGA)
640 x 480 @67Hz (Apple,Mac II)
640 x 480 @72Hz (VESA)
640 x 480 @75Hz (VESA) **********************************************************************
800 x 600 @56Hz (VESA) EDID data (128 bytes)
800 x 600 @60Hz (VESA) **********************************************************************
Established Timings II : 800 x 600 @72Hz (VESA) 0: 00 1: ff 2: ff 3: ff 4: ff 5: ff 6: ff 7: 00

800 x 600 @75Hz (VESA) 8: 41 9: 0c 10: 4a 11: 08 12: 02 13: 6f 14: 03 15: 00
832 x 624 @75Hz (Apple,Mac II) 16: 1b 17: 10 18: 01 19: 03 20: 0e 21: 28 22: 19 23: 78
1024 x 768 @60Hz (VESA) 24: 2a 25: e1 26: 60 27: a3 28: 55 29: 49 30: 99 31: 27
1024 x 768 @70Hz (VESA) 32: 13 33: 50 34: 54 35: bf 36: ee 37: 80 38: 71 39: 4f
1024 x 768 @75Hz (VESA) 40: 81 41: 40 42: 95 43: 00 44: 95 45: 0f 46: 01 47: 01
48: 01 49: 01 50: 01 51: 01 52: 01 53: 01 54: 9a 55: 29
Manufacturer's timings : 1152 x 870 @75Hz (Apple,Mac II) 56: a0 57: d0 58: 51 59: 84 60: 22 61: 30 62: 50 63: 98
64: 36 65: 00 66: 98 67: ff 68: 10 69: 00 70: 00 71: 1c
Standard Timing Identification #1 72: 00 73: 00 74: 00 75: fd 76: 00 77: 37 78: 4b 79: 1e
Horizontal active pixels : 1152 80: 53 81: 0e 82: 00 83: 0a 84: 20 85: 20 86: 20 87: 20
Aspect Ratio : 4:3 88: 20 89: 20 90: 00 91: 00 92: 00 93: fc 94: 00 95: 50
Refresh Rate : 75
96: 68 97: 69 98: 6c 99: 69 100: 70 101: 73 102: 20 103: 31
104: 39 105: 30 106: 43 107: 57 108: 00 109: 00 110: 00 111: ff
Standard Timing Identification #2
112: 00 113: 54 114: 59 115: 20 116: 31 117: 32 118: 33 119: 34
Horizontal active pixels : 1280
Aspect Ratio : 4:3 120: 35 121: 0a 122: 20 123: 20 124: 20 125: 20 126: 00 127: 6a
Refresh Rate : 60
DDC DATA 190CW7 LCD 25
THE DISPLAY DATA CHANNEL (DDC_2B) CONTENT INCLUDING: Standard Timing Identification #3
(FOR 190CW7 DIGITAL FOR CMO PANEL) Horizontal active pixels : 1440
********************************************************************** Aspect Ratio : 16:10
EDID log file Refresh Rate : 60
**********************************************************************
Standard Timing Identification #4
Vendor/Product Identification Horizontal active pixels : 1440
ID Manufacturer Name : PHL Aspect Ratio : 16:10
ID Product Code : 084A (HEX.) Refresh Rate : 75
ID Serial Number : 36F02 (HEX.)
Week of Manufacture : 27
Detailed Timing #1
Year of Manufacture : 2006
Pixel Clock (MHz) : 106.5
EDID Version, Revision H Active (pixels) : 1440
Version : 1 H Blanking (pixels) : 464
Revision : 3 V Active (lines) : 900
V Blanking (lines) : 34
Basic Display Parameters/Features H Sync Offset (F Porch) (pixels): 80
Video Input Definition : Digital Video Input H Sync Pulse Width (pixels) : 152
V Sync Offset (F Porch) (lines) : 3
Maximum H Image Size : 40 V Sync Pulse Width (lines) : 6
Maximum V Image Size : 25 H Image Size (mm) : 408
V Image Size (mm) : 255
Display Transfer Characteristic : 2.2 H Border (pixels) : 0
(gamma) V Border (lines) : 0
Flags : Non-interlaced
Feature Support (DPMS) : no Standby : Normal Display, No stereo
no Suspend : Digital Separate sync.
Active Off : Positive Vertical Sync.
: Negative Horizontal Sync.
Display Type : RGB color display
Preferred Timing Mode : Detailed timing block 1
Monitor Descriptor #2
Monitor Range Limits
Color Characteristics
Red X coordinate : 0.64 Min. Vt rate Hz : 55
Red Y coordinate : 0.334 Max. Vt rate Hz : 75
Green X coordinate : 0.285 Min. Horiz. rate kHz : 30
Green Y coordinate : 0.599 Max. Horiz. rate kHz : 83
Blue X coordinate : 0.153 Max. Supported Pixel : 140
Blue Y coordinate : 0.076
White X coordinate : 0.313 No secondary GTF timing formula supported.
White Y coordinate : 0.328
Monitor Descriptor #3
Established Timings Monitor Name : Philips 190CW
Established Timings I : 720 x 400 @70Hz (IBM,VGA)
640 x 480 @60Hz (IBM,VGA) Monitor Descriptor #4
640 x 480 @67Hz (Apple,Mac II) Serial Number : TY 123456
640 x 480 @72Hz (VESA)
640 x 480 @75Hz (VESA) Extension Flag : 0
800 x 600 @56Hz (VESA)
800 x 600 @60Hz (VESA) Check sum : E2 (HEX.)
Established Timings II : 800 x 600 @72Hz (VESA)
800 x 600 @75Hz (VESA)
********************************************************
832 x 624 @75Hz (Apple,Mac II)
1024 x 768 @60Hz (VESA) EDID data (128 bytes)
1024 x 768 @70Hz (VESA) ********************************************************
1024 x 768 @75Hz (VESA)
0: 00 1: ff 2: ff 3: ff 4: ff 5: ff 6: ff 7: 00
Manufacturer's timings : 1152 x 870 @75Hz (Apple,Mac II) 8: 41 9: 0c 10: 4a 11: 08 12: 02 13: 6f 14: 03 15: 00
16: 1b 17: 10 18: 01 19: 03 20: 80 21: 28 22: 19 23: 78
Standard Timing Identification #1 24: 2a 25: e1 26: 60 27: a3 28: 55 29: 49 30: 99 31: 27
Horizontal active pixels : 1152 32: 13 33: 50 34: 54 35: bf 36: ee 37: 80 38: 71 39: 4f
Aspect Ratio : 4:3 40: 81 41: 40 42: 95 43: 00 44: 95 45: 0f 46: 01 47: 01
Refresh Rate : 75 48: 01 49: 01 50: 01 51: 01 52: 01 53: 01 54: 9a 55: 29
56: a0 57: d0 58: 51 59: 84 60: 22 61: 30 62: 50 63: 98
Standard Timing Identification #2 64: 36 65: 00 66: 98 67: ff 68: 10 69: 00 70: 00 71: 1c
Horizontal active pixels : 1280 72: 00 73: 00 74: 00 75: fd 76: 00 77: 37 78: 4b 79: 1e
Aspect Ratio : 4:3 80: 53 81: 0e 82: 00 83: 0a 84: 20 85: 20 86: 20 87: 20
Refresh Rate : 60 88: 20 89: 20 90: 00 91: 00 92: 00 93: fc 94: 00 95: 50
96: 68 97: 69 98: 6c 99: 69 100: 70 101: 73 102: 20 103: 31
104: 39 105: 30 106: 43 107: 57 108: 00 109: 00 110: 00 111: ff
112: 00 113: 54 114: 59 115: 20 116: 31 117: 32 118: 33 119: 34
120: 35 121: 36 122: 0a 123: 20 124: 20 125: 20 126: 00 127: e2
26 190CW7 LCD Firmware Upgrade for CPU
Configuration and procedure

"Easywriter " The software is provided by Novatek to upgrade the
firmware of CPU.
It is a windows-based program, which cannot be run in MS-DOS.
DDC2BI_ISP TOOL (3138 149 53161) is for the interface between
"Parallel Port of PC" and "15 pin-D-SUB connector of Monitor".
System and equipment requirements

1. An i486 (or above) personal computer or compatible.
2. Microsoft operation system Windows 95/98/2000/XP.
3. ISP Software " Easywrite "
4. DDC2BI_ISP TOOL (3138 106 10396) as shown in Fig. 1 Fig. 4
Step 5 :Copy the 190CW7_NT68663_M190A1_EU_4C70_Org_V015

to C:\190CW7 as shown in Fig. 5 .
D-SUB to monitor
Parallel Port to Print Port in PC
Fig. 1
Fig. 5
5. Connect DDC2BI_ISP TOOL and Mains cord to Monitor as shown

in Fig. 2. Update the firmware
1. Double click the Easywriter.exe icon in desktop then appears
PC window as shown in Fig.7 .
190CW7-Monitor (B)
Monitor (A) D-Sub

- - - - - - - - - - - - - - - ->
To video card
Connect to Mains
Connect to cord at this moment.
Mains cord
ISP box
Video cable
Fig.2
6. Install and setup the Easywriter program
Step 1 : Make a folder in your PC as shown in Fig. 3. Fig. 6

For example : C:\190CW7
Step 2 : Copy ISP Software Easywriter.zip into your folder
as shown in Fig.3.
Step 3 : Unzip Easywriter.zip into your folder as shown in Fig. 3.
Step 4 : Double click the EasyWriterV2.10p2 icon to install the

Application as Fig. 4.
Fig. 3 Fig. 7
2. Press the Load hex then select the hex as shown in Fig. 8.
Firmware Upgrade for CPU 190CW7 LCD 27
If there is a warring message coming as shown in Fig 12. , you

have to check the AC power, Video cable, or Novatek MCU.
Fig. 8
3 Press the AUTO to running program , the firmware be updated

as shown in Fig. 9~10.
Fig. 12
5 Check the firmware version

Fig. 9 2). [Push "AUTO" & "MENU" buttons at the same time and hold them]
=> then release all buttons.
3).Press "MENU" button, wait until the OSD menu come on the
Screen of the monitor.You will find, after upgrade, the version
have already changed from The former"HUDSON 190CW7
V0.06 2006-06-01" to the Present "HUDSON 190CW7 V0.15
2006-06-26 as shown in Fig. 13 and Fig. 14.
Fig. 10
4 Press the file --> exit to end program , as shown in Fig. 11.
Factory Mode indicator Fig. 13
Fig. 11
Factory Mode indicator Fig. 14
4) Turn off the monitor, exit the factory mode.

28 190CW7 LCD Failure Mode Of Panel
Go to cover page
Quick reference for failure mode of LCD panel
this page presents problems that could be made by LCD panel.

It is not necessary to repair circuit board. Simply follow the mechanical
Polarizer has bubbles
instruction on this manual to eliminate failure by replace LCD panel.
Failure description Phenomenon
Vertical block defect

Polarizer has bubbles
Vertical dim lines
Foreign material inside

polarizer. It shows liner or
dot shape.
Vertical lines defect

(Always bright or dark)
Concentric circle formed
Horizontal block defect
Bottom back light of LCD is

brighter than normal
Horizontal dim lines
Back light un-uniformity
Horizontal lines defect

(Always bright or dark)
Backlight has foreign material.

Black or white color, liner or
Has bright or dark pixel circular type
Wiring Diagram 190CW7 LCD 29
CN801
CN802
12
CN902
29 1
1
12
CN406
CN701
CN803
18 1
CN403
CN804
1
12 1
CN101
30 190CW7 LCD Block Diagram
Scaler Diagram-1 190CW7 LCD 31
32 190CW7 LCD Scaler Diagram-2
34 190CW7 LCD Scaler Diagram-4
36 190CW7 LCD Scaler Board C.B.A.-1
Scaler Board C.B.A.-2 190CW7 LCD 37
38 190CW7 LCD Power Diagram-1
Power Diagram-2 190CW7 LCD 39
40 190CW7 LCD Power Board C.B.A.-1
715G1899-B-PHI
715G1899-B-PHI
Power Board C.B.A.-2 190CW7 LCD 41
715G1899-B-PHI
715G1899-B-PHI
42 190CW7 LCD Control Diagram
Control Board C.B.A. 190CW7 LCD 43
44 190CW7 LCD GENERAL PRODUCT SPECIFICATION
HUDSON7-190CW7
GENERAL PRODUCT
SPECIFICATION
. ANALOG AND DIGITAL DUAL INPUT
. AUTO PICTURE ADJUSTMENT
. 17 FACTORY PRESET MODES AND 40 PRESET MODES WHICH

CAN BE RECOVERED TO PRESET MODES, 24 USER MODES.
. USER FRIENDLY OSD DISPLAY FOR MODE IDENTIFICATION

/ADJUSTMENT
. MAX. RESOLUTION WXGA+ ( 1440 * 900 ) NON-INTERLACED AT 75 HZ
. 19"W COLOR TFT LCD FLAT PANEL
. EASY TILT BASE
. FULL RANGE POWER SUPPLY 100 - 240 VAC
. CE ENVIRONMENTAL POLICY
. ANTI-GLARE TO REDUCE LIGHT REFLECTION
. POWER MANAGEMENT CAPABILITY
. SOG SUPPORT
. TCO 03 99
. SMART CONTROL & SMART MANAGEMENT REQUIREMENT
. WEEE REQUIREMENT
. RoHS REQUIREMENT
19 inch TFT WXGA LCD Monitor

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 1
2006-06-22
GENERAL PRODUCT SPECIFICATION(Continued) 190CW7 LCD 45
CONTENTS
1 FOREWORD
2 PRODUCT PROFILE
2.1 LCD
2.2 SCANNING FREQUENCIES
2.3 A MBIENT TEMPERATURE : 0 °C - 35 °C
3 ELECTRICAL CHARACTERISTICS
3.1 INTERFACE SIGNALS

3.2 INTERFACE
3.3 TIMING REQUIREMENT
3.4 HORIZONTAL SCANNING
3.5 VERTICAL SCANNING
3.6 POWER INPUT CONNECTION
3.7 POWER MANAGEMENT
3.8 DISPLAY IDENTIFICATION
4 VISUAL CHARACTERISTICS
4.1 TEST CONDITIONS

4.2 B RIGHTNESS
4.3 IMAGE SIZE
4.4 B RIGHTNESS UNIFORMITY
4.5 CHECK CROSS TALK (S)
4.6 WHITE COLOR ADJUSTMENT
5 MECHANICAL CHARACTERISTICS
5.1 COSMETIC - PHILIPS TPV ID

5.2 MECHANICAL DATA FILES - PROE FILES REQUIRED
5.3 L OCATION OF PHILIPS LOGO - PER PHILIPS MAKE-UP SHEET
GAP BETWEEN PANEL AND FRONT BEZEL < 1.2 MM
L OCATION OF CONTROL ICONS - PER PHILIPS GRAPHIC SHEET
5.4 COLOR FOR RESIN/PAINT - PER PHILIPS MAKE-UP SHEET
5.5 RESINS
5.6 IF PAINT IS USED
5.7 PLASTIC MOLD TOOLING
5.8 PLASTICS FLAMMABILITY
5.9 TEXTURE/GLOSSING OF HOUSING
5.10 TILT AND SWIVEL BASE
5.11 L ABEL
5.12 PRODUCT DIMENSION / WEIGHT
5.13 TRANSPORTATION

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 2
2006-06-22
46 190CW7 LCD GENERAL PRODUCT SPECIFICATION(Continued)
GAP BETWEEN PANEL AND FRONT BEZEL < 1.2 MM

L OCATION OF CONTROL ICONS - PER PHILIPS GRAPHIC SHEET
5.4 COLOR FOR RESIN/PAINT - PER PHILIPS MAKE-UP SHEET
5.5 RESINS
5.6 IF PAINT IS USED
5.7 PLASTIC MOLD TOOLING
5.8 PLASTICS FLAMMABILITY
5.9 TEXTURE/GLOSSING OF HOUSING
5.10 TILT AND SWIVEL BASE
5.11 L ABEL
5.12 PRODUCT DIMENSION / WEIGHT
5.13 TRANSPORTATION
5.14 PALLET / CONTAINER LOADING
6 ENVIRONMENTAL CHARACTERISTICS
6.1 SUSCEPTIBILITY OF DISPLAY TO EXTERNAL ENVIRONMENT

6.2 TRANSPORTATION TESTS
6.3 DISPLAY DISTURBANCES FROM EXTERNAL ENVIRONMENT
6.4 DISPLAY DISTURBANCES TO EXTERNAL ENVIRONMENT
7 RELIABILITY
7.1 MEAN TIME B ETWEEN FAILURES
8 QUALITY ASSURANCE REQUIREMENTS
8.1 A CCEPTANCE TEST

9 Philips' Flat Panel Monitors Pixel Defect Policy

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 3
2006-06-22
1 FOREWORD
This specification describes a 19"W WXGA+ multi-scan color TFT LCD monitor with max. resolution up to
1440*900/76 75Hz non-interlaced.
All optical characteristics (including WHITE-D, Brightness, and so on) are determined according to panel
specification after warming up approximate 30 minutes that brightness stability is optimal, and follow strictly after
panel specification.
2 PRODUCT PROFILE
This display monitor unit is a color display monitor enclosed in PHILIPS global styling cabinet which has an
integrated tilt base.
2.1 LCD
2.1.1 Type NR. : M190A1
Outside dimensions : 427.2(w)*277.4(h)*17.0(d) (Typ) mm
Pitch ( mm ) : 0.285 mm x 0.285 mm
Color pixel arrangement : RGB vertical stripes
Display surface : low reflection, antiglare with hard coating
Color depth : 16.2M colors (6 bits+FRC)
Backlight : CCFL edge light system
Active area(WxH) : 410.4 x 256.5mm (19.05" diagonal)
View angle (CR>10) : 75/75 (min), 85/85 (typ) for Horizontal & 70/70 (min), 80/80 (typ) for Vertical
Contrast ratio : 850:1(Typ.) 500:1(Min.)
White luminance : Original color 230 nits (Min), 300 nits (Typ.)
Gate IC :
Source IC :
Response time : 5ms (typ)
2.2 Scanning frequencies

Hor. : 30 - 83 K Hz
Ver. : 55 - 75Hz
Video dot rate : <140 MHz
Power input : 90-264 V AC, 50/60 ± 2 Hz
Power consumption : < 36W(typ.) maximum
2.3 Ambient temperature : 0 °C - 35 °C
3 Electrical characteristics
3.1 Interface signals
1). D-Sub Analog
Input signal : Video, Hsync., Vsync
Video : 0.7 Vp-p, input impedance, 75 ohm @DC
Sync. : Separate sync TTL level , input impedance 2.2k ohm terminate
Hsync Positive/Negative
Vsync Positive/Negative
Composite sync TTL level, input impedance 2.2k ohm terminate (Positive/Negative)
Sync on green video 0.3 Vp-p Negative (Video 0.7 Vp-p Positive)

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 4
2006-06-22
2). Intel DVI Digital
Input signal : Four channel TMDS signal
3.2 Interface
3 .2.1 D-Sub Cable
Length : 1.8 M +/- 50 mm (fixed) , fix in monitor and with transplant pin
protect cover.
Connector type : D-Sub male with DDC2B pin assignments.
Blue connector thumb-operated jack screws
pin assignment :
PIN No. SIGNAL

1 Red
2 Green/ SOG
3 Blue
4 Sense (GND)
5 Cable Detect (GND)
6 Red GND
7 Green GND
8 Blue GND
9 DDC +3.3V or +5V
10 Logic GND
11 Sense (GND)
12 Bi-directional data
13 H/H+V sync
14 V-sync
15 Data clock
3.2.2 DVI Cable
The input signals are applied to the display through DVI-D cable.
Length : 1.8 M +/- 50mm (fixed)
Connector type : DVI-D male with DDC2B pin assignments
White connector thumb-operated jack screws
pin assignment :

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 5
2006-06-22
Note the mark "*" for DVI-I to Dsub only
Pin No. Description

1 TMDS data2-
2 TMDS data2+
3 TMDS data2 shield
4 NC
5 NC
6 DDC clock
7 DDC data
8 * Analog V-sync
9 TMDS data1-
10 TMDS data1+
11 TMDS data1 shield
12 NC
13 NC
14 +5V
15 Ground(return for +5V and H/V-sync)(Cable Detect)
16 Hot plug detect
17 TMDS data0-
18 TMDS data0+
19 TMDS data0 shield
20 NC
21 NC
22 TMDS clock shield
23 TMDS clock+
24 TMDS clock-
C1 * Analog R
C2 * Analog G
C3 * Analog B
C4 * Analog H-sync
C5 * Analog GND (Analog R, G, B return)
3.2.3 Software control functions via OSD/control adjustable functions:

OSD control bottom sequence.
Auto - Left (Brightness) - Power - Right (Contrast) - Menu

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 6
2006-06-22
(1) PC Analog Signal Input Mode
Adjustable functions:
1st LEVEL 2nd LEVEL 3rd LEVEL
MONITOR SETUP
Exit
Brightness & Contrast Brightness

Contrast
Color Original Color, 9300K,6500K, sRGB, User
Define
Position Horizontal
Vertical
Input Selection Analog [ Digital ]
More Settings Language /00,/05 : English, Spanish, French,

German, Italian and Russian
/27 : English, French, Spanish,
Portuguese & S. Chinese
/69,/75,/93,/96 : English, Spanish,
French, German, Italian and S. Chinese
Phase/ Clock Phase
Clock
OSD Settings Horizontal
Vertical
Reset No
Yes
Serial No.:
(Serial No.)
Timing Mode
Up/Down left / right to Move

and to Adjust,ok menu to
Confirm

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 7
2006-06-22
(2) Digital interface OSD :
Adjustable functions:
1st LEVEL 2nd LEVEL 3rd LEVEL
MONITOR SETUP
Exit
Brightness & Contrast Brightness

Contrast
Color Original Color, 9300K,6500K, sRGB, User
Define
Position Horizontal
Vertical
Input Selection Analog,[ Digital]
More Settings Language /00 : English, Espanol, Frencais,

Deutsch, Italiano, , Russian
/27 : English, Espanol, Frencais,
Portuguess, S-Chinese
/69,/75,/93,/96 : English, Espanol,
Frencais, Deutsch, Italiano, , S-Chinese
Phase/ Clock Phase
Clock
OSD Settings Horizontal
Vertical
Reset No
Yes
Serial No.:
(Serial No.)
Timing Mode
Up/Down left / right to

Move and to Adjust,ok
menu to Confirm
Remark : < to Adjust > / < to Move > - < to Confirm >
Remark : Color Temperature factory default setting = see 190CW7 SKU.

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 8
2006-06-22
3.3 Timing requirement
3.3.1 Mode storing capacity
Factory preset modes : 17

Preset modes : 40
User define modes : 24
Note: 1. Screen displays perfect picture at 17 factory-preset modes.

2. Screen displays visible picture with OSD warning when input modes are the
33 preset modes
3.3.2 Factory preset modes (17 modes)
Item H.Freq. Mode Resolution V.Freq. Item H.Freq. Mode Resolution V.Freq.
(KHz) (Hz) (KHz) (Hz)
1 31.469 DOS 720x400 70.087 11 60.023 VESA 1024x768 75.029
2 31.469 VESA 640x480 59.940 12 67.500 VESA 1152x864 75.000
3 37.861 VESA 640x480 72.809 13 47.712 VESA 1360x768 60.015
4 37.500 VESA 640x480 75.000 14 55.935 VESA 1440x900 59.887
5 35.156 VESA 800x600 56.250 15 70.635 VESA 1440x900 74.984
8 46.875 VESA 800x600 75.000 18
9 48.363 VESA 1024x768 60.004 19
10 56.476 VESA 1024x768 70.069 20

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 9
2006-06-22
3.3.3 Preset Modes (33 40 modes)
MODE NO. 1 2 3 4
RESOLUTION 640 x 350 720 x 400 640 x 480 640 x 480
Dot clock(MHz) 25.175 28.321 25.175 30.24

fh 31.469kHz 31.468kHz 31.5kHz 35 kHz
A ( us ) 31.778(800 dots) 31.78(900dots) 31.778(800 dots) 28.571 (864 dots)
B ( us ) 3.813(96 dots) 3.813(108dots) 3.813( 96 dots) 2.116 ( 64 dots)
C ( us ) 1.907(48 dots) 1.907(54dots) 1.907( 48 dots) 3.175( 96 dots)
D ( us ) 25.422(640 dots) 25.42(720dots) 25.422( 640 dots) 21.164( 640 dots)
E ( us ) 0.636(16 dots) 0.636(18dots) 0.636( 16 dots) 2.116( 64 dots)
fv 70Hz(70.09) 70Hz(70.085) 60Hz 67Hz
O (ms ) 14.27(449 lines) 14.27(449 lines) 16.683 (525 lines) 15 (525 lines)
P ( ms ) 0.064(2 lines) 0.064(2 lines) 0.064 ( 2 lines) 0.086( 3 lines)
Q (ms ) 1.907(60 lines) 1.080(34 lines) 1.049 ( 33 lines) 1.114( 39 lines)
R ( ms ) 11.12(350 lines) 12.71(400 lines) 15.253 (480 lines) 13.714(480 lines)
S ( ms ) 1.175(37 lines) 0.381(13 lines) 0.317 ( 10 line ) 0.086( 3 line )
SYNC. H/V +/- -/+ -/- -/-
POLARITY
SEP . SYNC Y Y Y Y
MODE NO. 5 6 7 8
RESOLUTION 640 x 480 640 x 480 640x480 800 x 600
Dot clock(MHz) 31.500 31.501 36 36
fh 37.861kHz 37.5kHz 36kHz 35.2kHz

A ( us ) 26.413(832 dots) 26.667 (840 dots) 23.111 (832 dots) 28.444(1024 dots)
B ( us ) 1.270(40 dots) 2.032 ( 54 dots) 1.556 (56 dots) 2.000 ( 72 dots)
C ( us ) 3.810(120 dots) 3.81 ( 120 dots) 2.222 ( 80 dots) 3.556 ( 128 dots)
D ( us ) 20.317(640 dots) 20.317 (640 dots) 17.778 (640 dots) 22.222( 800 dots)
E ( us ) 1.016(32 dots) 0.508 ( 26 dots) 1.555 (56 dots) 0.666 ( 24 dots)
fv 72.809Hz 75Hz 85Hz 56Hz

O (ms ) 13.735(520 lines) 13.333 (500 lines ) 11.763 (509 lines ) 17.778 (625 lines)
P ( ms ) 0.079(3 lines) 0.08 ( 3 lines ) 0.069 ( 3 lines ) 0.057 ( 2 lines)
Q (ms ) 0.528(20 lines) 0.427 ( 16 lines ) 0.578 ( 25 lines ) 0.626 ( 22 lines)
R ( ms ) 12.678(480 lines) 12.8 (480 lines ) 11.093 (480 lines ) 17.066 (600 lines)
S ( ms ) 0.45(17 lines) 0.026 ( 1 lines) 0.023 ( 1 lines) 0.029 ( 1 line )
SYNC. H/V -/- -/- -/- +/+
POLARITY
SEP . SYNC Y Y Y Y

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 10
2006-06-22
MODE NO. 9 10 11 12
RESOLUTION 800 x 600 800 x 600 800 x 600 800 x 600
Dot clock(MHz) 40 50 49.498 56.251
fh 37.9kHz 48.077kHz 46.9kHz 53.7kHz

A ( us ) 26.4 (1056 dots) 20.80 (1040dots) 21.333 (1056 dots) 18.631 (1048 dots)
B ( us ) 3.2 ( 128 dots) 2.400 ( 120 dots) 1.616 ( 80 dots) 1.138 ( 64 dots)
C ( us ) 2.2 ( 88 dots) 1.280 ( 64 dots) 3.232 ( 160 dots) 2.702 ( 152 dots)
D ( us ) 20 ( 800 dots) 16.00 ( 800 dots) 16.162 ( 800 dots) 14.222 ( 800 dots)
E ( us ) 1 ( 40 dots) 1.120 ( 56 dots) 0.323 ( 16 dots) 0.569 ( 32 dots)
fv 60Hz 72Hz ( 72.188) 75Hz 85Hz

O (ms ) 16.579 (628 lines) 13.85 (666 lines) 13.333 (625 lines) 11.756(631 lines)
P ( ms ) 0.106 ( 4 lines) 0.125 ( 6 lines) 0.064 ( 3 lines) 0.056 ( 3 lines)
Q (ms ) 0.607 ( 23 lines) 0.478 ( 23 lines) 0.448 ( 21 lines) 0.503 ( 27 lines)
R ( ms ) 15.84 (600lines) 12.48 (600 lines) 12.8 (600 lines) 11.179 (600 lines)
S ( ms ) 0.026 ( 1 line ) 0.770 ( 37 line ) 0.021 ( 1 line ) 0.018 ( 1 lines)
SYNC. H/V +/+ +/+ +/+ +/+
POLARITY
SEP . SYNC Y Y Y Y
MODE NO. 13 14 15 16
RESOLUTION 832 x 624 1024 x 768 1024 x 768 1024 x 768
Dot clock(MHz) 57.28 65 75 78.75
fh 49.7kHz 48.363kHz 56.5kHz 60kHz

A ( us ) 20.11(1152 dots) 20.677(1344 dots) 17.707(1328 dots) 16.66 (1312dots)
B ( us ) 1.117(64 dots) 2.092(136 dots) 1.813(136 dots) 1.219 ( 96 dots)
C ( us ) 3.91(224 dots) 2.462(160 dots) 1.920(144 dots) 2.235 ( 176 dots)
D ( us ) 14.52(832 dots) 15.754(1024 dots) 13.653(1024 dots) 13.003 ( 1024 dots)
E ( us ) 0.563(32 dots) 0.369(24 dots) 0.321 (24 dots) 0.203 ( 16 dots)
fv 75Hz 60.004Hz 70.004Hz 75Hz ( 75.000)

O (ms ) 13.41(667 lines) 16.666(806 lines) 14.272(806 lines) 13.328 (800 lines)
P ( ms ) 0.06(3 lines) 0.124(6 lines) 0.106(6 lines) 0.05( 3 lines)
Q (ms ) 0.784(39 lines) 0.600(29 lines) 0.514(29 lines) 0.446 ( 28 lines)
R ( ms ) 12.55(624 lines) 15.880(768 lines) 13.599(768 lines) 12.80 (768 lines)
S ( ms ) 0.016(1 lines) 0.062(3 lines) 0.053(3 lines) 0.017 ( 1 line )
SYNC. H/V +/+ -/- -/- +/+
POLARITY
SEP . SYNC Y Y Y Y
MODE NO. 17 18 19 20
RESOLUTION 1024 x 768 1024 x 768 1152 x 864 1152 x 864
Dot clock(MHz) 83.096 94.5 79.9 94.5
fh 61.1kHz 68.7kHz 54.0kHz 63.9kHz

A ( us ) 16.367 (1360dots) 14.561 (1376 dots) 18.523(1480 dots) 15.661(1480 dots)
B ( us ) 1.348 ( 112 dots) 1.016 ( 96 dots) 1.952(156 dots) 1.016(96 dots)
C ( us ) 2.022 ( 168 dots) 2.201 ( 208 dots) 1.352(108 dots) 1.116(105 dots)
D ( us ) 12.323 ( 1024 dots) 10.836 ( 1024 dots) 14.418(1152 dots) 12.19(1152 dots)
E ( us ) 0.674 ( 56 dots) 0.508 ( 48 dots) 0.801(64 dots) 1.339(127 dots)
fv 76Hz 85Hz 60Hz 70Hz

O (ms ) 13.142 (803 lines) 11.765 (808 lines) 16.671(900lines) 14.283(912lines)
P ( ms ) 0.049 ( 3 lines) 0.044 ( 3 lines) 0.148(8 lines) 0.047(3lines)
Q (ms ) 0.507 ( 31 lines) 0.524 ( 36 lines) 0.445(24 lines) 0.689(44 lines)
R ( ms ) 12.57 (768 lines) 11.183 (768lines) 16.004(864 lines) 13.531(864 lines)
S ( ms ) 0.016 ( 1 line ) 0.014 ( 1 line ) 0.074(4 lines) 0.016(1 lines)
SYNC. H/V +/+ +/+ +/+ +/+
POLARITY
SEP . SYNC Y Y Y Y

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 11
2006-06-22
MODE NO. 21 22 23 24
RESOLUTION 1152 x 864 1152 x 870 1152 x 900 1152 x 900
Dot clock(MHz) 108 100 94.5 108
fh 67.5kHz 68.7kHz 61.8kHz 71.8kHz
A ( us ) 14.815 (1600 dots) 14.56 (1456 dots) 16.169 (1528 dots) 13.926 (1054dots)
B ( us ) 1.185 ( 128 dots) 1.28 ( 128 dots) 1.354 ( 128 dots) 1.185 ( 128 dots)
C ( us ) 2.37 ( 256 dots) 1.44( 144 dots) 2.201 ( 208 dots) 1.778 ( 192 dots)
D ( us ) 10.667 ( 1152 dots) 11.52 ( 1152 dots) 12.19 ( 1152 dots) 10.667 ( 1152 dots)
E ( us ) 0.593 ( 64 dots) 0.32 ( 32 dots) 0.424 ( 40 dots) 0.296 ( 32 dots)
O (ms ) 13.333 (900 lines) 13.333 (916 lines) 15.151 (937lines) 13.132 (943 lines)
P ( ms ) 0.044 ( 3 lines) 0.044 ( 3 lines) 0.065 ( 4 lines) 0.111 ( 8 lines)
Q (ms ) 0.474 ( 32 lines) 0.568( 39 lines) 0.501 ( 31 lines) 0.46 ( 33 lines)
R ( ms ) 12.8 (864 lines) 12.678 (870 lines) 14.552 (900lines) 12.533 (900 lines)
S ( ms ) 0.015 ( 1 lines) 0.043 ( 4 line ) 0.033 ( 2 line ) 0.028 ( 2 lines)
SYNC. H/V -/- -/- Serr- +/+
POLARITY
SEP . SYNC Y Y Y Y
MODE NO. 25 26 27 28
RESOLUTION 1280 x 960 1280 x 960 1280 x 1024 1280 x 1024
Dot clock(MHz) 108 129.895 108 117
fh 60kHz 75kHz 64kHz 71.7kHz
A ( us ) 16.667(1800 dots) 13.307 (1728 dots) 15.63 (1688 dots) 13.949 (1632 dots)
B ( us ) 1.037(112 dots) 1.047 ( 136 dots) 1.037 ( 112 dots) 0.957 (112 dots)
C ( us ) 2.889(312 dots) 1.725 ( 224 dots) 2.296 ( 248 dots) 1.915 (224 dots)
D ( us ) 11.852(1280 dots) 9.857 ( 1280 dots) 11.852 ( 1280 dots) 10.94 (1280 dots)
E ( us ) 0.889(96 dots) 0.678 ( 88 dots) 0.445 ( 48 dots) 0.137 (16 dots)
O (ms ) 16.667(1000 lines) 13.333 (1002 lines) 16.661 (1066 lines) 14.883 (1067lines)
P ( ms ) 0.05(3 lines) 0.039 ( 3 lines) 0.047 ( 3 lines) 0.112 ( 8 lines)
Q (ms ) 0.600(36 lines) 0.48 ( 36 lines) 0.594 ( 38 lines) 0.46 ( 33 lines)
R ( ms ) 16(960 lines) 12.774 (960 lines) 16.005 (1024 lines) 14.283 (1024 lines)
S ( ms ) 0.017(1 lines) 0.04 ( 3 lines ) 0.015 ( 1 line) 0.028 (2 lines )
SYNC. H/V +/+ +/+ +/+ +/+
POLARITY
SEP . SYNC Y Y Y Y
MODE NO. 29 30 31 32
RESOLUTION 1280 x 1024 1280 x 1024 1280 x 1024 1360 x 768
Dot clock(MHz) 130.223 135 138.008 85.5
Fh 76kHz 80kHz 81.1kHz 47.712kHz
A ( us ) 13.158 (1712 dots) 12.504(1688 dots) 12.326 (1664 dots) 20.959(1792 dots)
B ( us ) 1.024 ( 133 dots) 1.067(144 dots) 0.474 (64 dots) 1.31(112 dots)
C ( us ) 1.905 ( 248 dots) 1.837(248 dots) 2.133 (288 dots) 2.994(256 dots)
D ( us ) 9.83 ( 1280 dots) 9.481(1280 dots) 9.481 (1280 dots) 15.906(1360 dots)
E ( us ) 0.399( 51 dots) 0.119(16 dots) 0.238 (32 dots) 0.749(64 dots)
Fv 72Hz 75Hz 76Hz 60.015Hz
O (ms ) 14 (1064 lines) 13.329(1066 lines) 13.139 (1066 lines) 16.662(795 lines)
P ( ms ) 0.02 ( 2 lines) 0.038(3 lines) 0.099 ( 8 lines) 0.126(6 lines)
Q (ms ) 0.5 ( 38 lines) 0.475(38 lines) 0.394 ( 32 lines) 0.377(18 lines)
R ( ms ) 13.468 (1024 lines) 12.804(1024 lines) 12.622 (1024 lines) 16.097(768 lines)
S ( ms ) 0.012 ( 0 line) 0.012 (1 line) 0.024( 2 lines ) 0.063(3 lines)
SYNC. H/V +/+ +/+ -/- +/+
POLARITY
SEP . SYNC Y Y Y Y

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 12
2006-06-22
MODE NO. 33 34 35 36
RESOLUTION 1440 x 900 1440 x 900 1280x720 1280x720
Dot clock(MHz) 106.50 136.75 74.5 89.04
Fh 55.935kHz 70.635kHz 44.772KHz 52.5KHz

A ( us ) 17.878(1904 dots) 14.157(1936 dots) 22.335 19.048
B ( us ) 1.427(152 dots) 1.112(152 dots) 1.718 1.527
C ( us ) 2.718(232 dots) 1.814(248 dots) 2.577 2.336
D ( us ) 13.521(1440 dots) 10.53(1440 dots) 17.181 14.376
E ( us ) 0.751(80 dots) 0.702(96 dots) 0.859 0.809
Fv 59.887Hz 74.984Hz 59.855 70

O (ms ) 16.698(934 lines) 13.336(942 lines) 16.707 14.286
P ( ms ) 0.107(6 lines) 0.085(6 lines) 0.112 0.057
Q (ms ) 0.447(25 lines) 0.467(33 lines) 0.447 0.495
R ( ms ) 16.09(900 lines) 12.741(900 lines) 16.082 13.714
S ( ms ) 0.054(3 lines) 0.042(3 lines) 0.067 0.019
SYNC. H/V -/+ -/+ -/+ -/+
POLARITY
SEP . SYNC Y Y Y Y
MODE NO. 37 38 39 40
RESOLUTION 1280x720 1280 x 768 1280 x 768 1280 x 768
Dot clock(MHz) 95.75 79.5 94.976 102.25
Fh 56.456KHz 47.776kHz 56kHz 60.289kHz

A ( us ) 17.713 20.931 17.857 16.587
B ( us ) 1.337 1.61 1.432 1.252
C ( us ) 2.172 2.415 2.19 2.034
D ( us ) 13.368 16.101 13.477 12.518
E ( us ) 0.836 0.805 0.758 0.782
Fv 74.777 59.87Hz 70Hz 74.893Hz

O (ms ) 13.373 16.703 14.286 13.352
P ( ms ) 0.089 0.147 0.054 0.116
Q (ms ) 0.478 0.419 0.5 0.448
R ( ms ) 12.753 16.075 13.714 12.739
S ( ms ) 0.053 0.063 0.018 0.05
SYNC. H/V -/+ -/+ -/+ -/ +
POLARITY
SEP . SYNC Y Y Y Y

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 13
2006-06-22
3.4 Horizontal scanning
Sync polarity : Positive or Negative

Scanning frequency : 30 - 83 K Hz
3.5 Vertical scanning
Sync polarity : Positive or Negative

Scanning frequency : 55 - 75 Hz
3.6 Power input connection
Power cord length : 1.8 M

Power cord type : 3 leads power cord with
protective earth plug.
3.7 Power management
The monitor must comply with the Microsoft On Now specification, with two power management
states, as defined by the VESA DPMS document. The monitor must appropriately display the
DPMS state.
Mode HSYNC VSYN Video Pwr-cons. Indication Rec.

C time
Power-On On On active < 36 W(typ..) Green LED --
34 W (typ.)
Off Off Off blanked <1W Amber LED <3s
DC Power N/A <1W LED Off

Off
3.8 Display identification
In accordance with VESA Display Channel Standard Ver.1.0 and having DDC 2B capability
4 Visual characteristics
4.4 Test conditions
Unless otherwise specified, this specification is defined

under the following conditions.
(1) Input signal : As defined in 3.3, 1440 x 900

non-interlaced mode ( 56K/60Hz ), signal
sources must have 75 ohm output impedance.
(2) Luminance setting : controls to be set to 300 nits with

full screen 100 % duty cycle white signal
(3) Warm up: more than 30 minutes after power on with signal supplied.
(4) Ambient light : 400 -- 600 lux.
(5) Ambient temperature : 20 ± 5 °C
4.5 Brightness
> 300 nits (at panel color temperature, at center of the screen, set contrast
and brightness at maximum. )

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 14
2006-06-22
4.3 Image size
Actual display size 410.4 x 256.5mm
4.4 Brightness uniformity
Set contrast at 100% and turn the brightness to get average above 300 nits
at centre of the screen.
Apply the Fig 1, it should comply with the following formula:
B_min
X 100% >75%
B_max
Where B_max =Maximum brightness

B_min = Minimum brightness
4.5 Check Cross talk (S)
Apply Pattern 2. Set contrast and brightness at 100 %.

Measure YA. Then output Pattern 3 and measure YB.
the cross talk value :
ABS( YA - YB )
¾¾¾¾¾¾¾¾¾ X 100% < 1.5 %
YA
4.6 White color adjustment
There are three factory preset white color 9300K, 6500K, sRGB.
Apply full white pattern, with brightness in 100 % position

and the contrast control at 50 % position.
The 1931 CIE Chromaticity (color triangle) diagram (x,y)
coordinate for the screen center should be:
Product spec.
Y = 0.297 ± 0.02

Y = 0.329 ± 0.02

Y = 0.329 ± 0.02
Production alignment spec.

Y = 0.297 ± 0.005

Y = 0.329 ± 0.005

Y = 0.329 ± 0.005

Y = 0.297 ± 0.015

Y = 0.329 ± 0.015

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 15
2006-06-22

Y = 0.329 ± 0.015
5 Mechanical characteristics
5.1 Cosmetic - Philips TPV ID
5.2 Mechanical data files - ProE files required
5.3 Location of Philips logo - Per Philips make-up sheet
Gap between panel and front bezel < 1.2 mm
Location of Control icons - Per Philips Graphic Sheet
Front side: Per Philips graphic sheet

Rear : Per Philips graphic sheet
5.4 Color for resin/paint - Per Philips make-up sheet
5.5 Resins
· RoHS required
· WEEE required.
· Resin type/selection refer to Project Book Section 7.2 Plastic material.
5.6 If paint is used
· RoHS required
· WEEE require
5.7 Plastic mold tooling
· Tooling to be designed to minimize cosmetic defects induced by molding process (sink, blush, weld
lines, gate marks, ejector marks, etc.).
· Painting to cover up cosmetic defects due to molding is strongly discouraged.
5.8 Plastics flammability
· All Plastics to be Flame Retardant UL 94-V0 or Better (if monitor weighs less than 18kg; UL94-V0 is
OK).
· All major plastic parts (bezel, back cover ) need to be molded from same resin.
5.9 Texture/Glossing of housing
· The texture area and texture no should follow Philips make-up sheet TPV Spec.
· The exterior surfaces shall have a uniform texture.
· Philips must approve the mold texturing.
· Detail document for texture refer to UAN-D249.
· < = 20 gloss units

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 16
2006-06-22
5.10 Tilt and swivel base
· Tilt angle : -5 ° max.(forward) and +20° min.(backward )

5.11 Label
· Regulatory label / Carton label should follow Philips requirement.

· Detail document refer to Philips Engineering Reference Book.
5.12 Product dimension / Weight
· Unit dimension (incl. pedestal) : 438.5(W) * 358 (H) * 211 (D) mm

· Packed unit dimension (WW carton) : 520W* 190 H* 392 Dmm)
· Packed unit dimension ( China carton ) :
· Net weight : 5.0Kg
· Gross weight : 6.7Kg
·
5.13 Transportation
Transportation standards refer to TYE-M0002

5.13.1Transportation packages
Packaging and wrapping shall be sufficient to protect the product against damage or loss
during shipment from the supplier to the destination specified in the purchase order. All
packaging materials are subject to test and evaluation per TYE-M0002. The cushion material
shall be constructed using EPS material.
5.13.2 Transportation Test
The overall test refer to TYE-M0002.

Vibration, drop test should be performed at ambient temperature(20oC to 23oC) and relative humidity
(40% to 65% ).
A. Transportation test specification for all regions except China/India
· Package test
1. Random Vibration test
2. Drop test
3. Cold Drop test (for design reference)
· Un-package test
1. Half sine shock test (non operation)
B. Transportation test specification for China/India
· Package test
1. Random Vibration test
2. Drop test
3. Cold Drop test (for design reference)
· Un-package test
1. Sine vibration (operating)
2. Half sine shock test (non operation)

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 17
2006-06-22
5.14 Pallet / Container loading

Except China
Transportation standards refer to TYE-M0002. Pallet Slip sheet
· Air shipment - ---
· Sea container 20'(pallet/slip sheet) - 660 ---
· Sea container 40'(pallet/slip sheet) - 1386 ---
· Sea container 40' High Cube (pallet/slip sheet) - 1008 1008
· Truck shipment- tbc
A. Air shipment
B. Container loading for other regions
C. Truck loading for other regions
6 Environmental characteristics
The following sections define the interference and

susceptibility condition limits that might occur
between external environment and the display device.
6.1 Susceptibility of display to external environment
Operating
- Temperature : 0 to 40 degree C
Storage
- Temperature : -20 to 60 degree C
Note: recommend at 5 to 35°C, Humidity less than 60 %
6.2 Transportation tests
Refer to 5.15.2
6.3 Display disturbances from external environment
According to IEC 801-2 for ESD disturbances
6.4 Display disturbances to external environment
7 Reliability
7.1 Mean Time Between Failures
System MTBF (Including the LCD panel and CCFL) : 50,000 hrs
8 Quality assurance requirements

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 18
2006-06-22
8.1 Acceptance test
According to MIL-STD-105D Control II level
AQL: 0.4 (major)

1.5 (minor)
(Please also refer to annual quality agreement)
Customer acceptance criteria: UAW0377/00
9 Philips' Flat Panel Monitors Pixel Defect Policy
Philips' Flat Panel Monitors Pixel Defect Policy

BRIGHT DOT DEFECTS ACCEPTABLE LEVEL
190CW7
MODEL
1 lit sub-pixel 2 3
2 adjacent lit sub-pixels 0 1
3 adjacent lit sub-pixels (one white pixel) 0
Distance between two bright dot defects* 25mm or more
15mm
25mm
Bright dot defects within 20 mm circle 0
Total bright dot defects of all type 3
BLACK DOT DEFECTS ACCEPTABLE LEVEL

190CW7
MODEL
1 dark sub-pixel 4 5
2 adjacent dark sub-pixels 2 12
3 adjacent dark sub-pixels (one white pixel) 0
Distance between two black dot defects* 15mm or
More
15mm
Black dot defects within 20 mm circle* 1

Total black dot defects of all type 4 5
TOTAL DOT DEFECTS ACCEPTABLE LEVEL

190CW7
MODEL
Total bright or black dot defects of all type 5
* 1 or 2 adjacent sub-pixel defects = 1 dot defect

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 19
2006-06-22
Fig 1: Brightness Uniformity
320 640 960 PIXEL
256
P2 P6 P3
512
P7 P1 P8
768
P4 P9 P5
Fig 2: Cross talk pattern

Gray level 46 (64 Gray level)
1/6
1/2
YA
1/2

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 20
2006-06-22
Fig 3: Cross talk Pattern

Center at Gray level 0 (Black)
1/3 1/3 1/6
1/3
1/2
1/3
YB
1/2
1/3

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 21
2006-06-22
SEPARATE SYNC.
VIDEO
C D E
HORIZONTAL
B
A
VIDEO
Q R S
VERTICAL
P
O
COMPOSITE SYNC.
VIDEO
C D E
HORIZONTAL
B
A
FIG-4 TIMING CHART -1

TYPE : 190CW7CS/00 8639 000 17256
BRAND : PHILIPS
2006-06-22
22 590 22
2006-06-22
9965 000 39716 9965 000 39713 9965 000 39717
66
A33G0067VO1T 750GLM90A1211N A34G0051VB1T
KEY BUTTON PANEL LCD 19" A1-L02 CMO REAR COVER
5
2
9965 000 39714 9965 000 39721 Type: 190CW7CS/00

A33G00601C CBPC6MNNPHA
POWER LENS CONVERSION BOARD
190CW7 LCD
9965 000 39723

PWPC942MR1P
POWER BOARD ASSY
9965 000 39720

A37G00071
HINGE
Exploded View
9965 000 39722

KEPC6AP1
KEY BOARD 6
9965 000 39718
A34G0053VB1B
STAND TOP
7
1
9965 000 39719
9965 000 39715 A34G0054VB1B
A34G0112VOA2T STAND BOTTOM
FRONT BEZEL PHILIPS
8
9965 000 39710
034G1844VB1B
BASE
Repair Tips 190CW7 LCD 67
0. Warning preferably be equipped with a thermal control (soldering

All ICs and many other semi-conductors are susceptible to temperature: 225 to 250 C).
electrostatic discharges (ESD). Careless handling during - The chip, once removed, must never be reused.
repair can reduce life drastically. When repairing, make sure 1.4 Attachment of SMDs
that you are connected with the same potential as the mass - Locate the SMD on the solder lands by means of tweezers
of the unit via a wrist wrap with resistance. Keep components and solder the component on one side. Ensure that the
and tools also at the same potential ! component is positioned correctly on the solder lands (see Fig.2A).
1. Servicing of SMDs (Surface Mounted Devices) - Next complete the soldering of the terminals of the
1.1 General cautions on handling and storage component (see Fiq. 2B).
- Oxidation on the terminals of SMDs results in poor soldering.

Do not handle SMDs with bare hands.
- Avoid using storage places that are sensitive to oxidation
such as places with sulphur or chlorine gas, direct sunlight,
high temperatures or a high degree of humidity. The
capacitance or resistance value of the SMDs may be
affected by this.
- Rough handling of circuit boards containing SMDs may
cause damage to the components as well as the circuit
boards. Circuit boards containing SMDs should never be
bent or flexed. Different circuit board materials expand and
contract at different rates when heated or cooled and the 2. Caution when attaching SMDs
components and/or solder connections may be damaged - When soldering the SMD terminals, do not touch them
due to the stress. Never rub or scrape chip components as directly with the soldering iron. The soldering should be
this may cause the value of the component to change. done as quickly as possible, care must be taken to avoid
Similarly, do not slide the circuit board across any surface. damage to the terminals of the SMDs themselves.
- Keep the SMD's body in contact with the printed board when
1.2 Removal of SMDs soldering.
- Heat the solder (for 2-3 seconds) at each terminal of the - The soldering iron to be used (approx. 30 W ) should
chip. By means of litz wire and a slight horizontal force, preferably be equipped with a thermal control (soldering
small components can be removed with the soldering iron. temperature: 225 to 250 C).
They can also be removed with a solder sucker (see Fig. - Soldering should not be done outside the solder land.
1A) - Soldering flux (of rosin) may be used, but should not be
acidic.
- After soldering, let the SMD cool down gradually at room
temperature.
- The quantity of solder must be proportional to the size of the
solder land. If the quantity is too great, the SMD might
crack or the solder lands might be torn loose from the
printed board (see Fig. 3).
While holding the SMD with a pair of tweezers, take it off gently using the
Right
soldering iron's heat applied to each terminal (see Fig. 1 B).
- Remove the excess solder on the solder lands by means of
Fig.3 Examples
litz wire or a solder sucker (see Fig. 1C).
1.3 Caution on removal

- When handling the soldering.iron. use suitable pressure and be careful.
- When removing the chip, do not use undue force with the pair of tweezers.
- The soldering iron to be used (approx. 30 W) should
68 190CW7 LCD Repair Tips
3. Lead-free product identification
You can identify lead-free product by Philips-lead-free logo on PCB.
4. Lead-free product repair instruction
4.1 Use only lead-free Solder Alloy 0622 149 00106(1.2mm SAC305) or 0622 14900108(1.0mm SAC305).
Remark: For lead free soldering material, please visit www.alphametals.com website for details. This is recommended by Philips.
4.2 Use only adequate solder tools applicable for lead-free soldering-tin. The solder tool must be able to reach at least a
solder-temperature of 400 , to stabilize the adjusted temperature at the solder-tip and to exchange solder-tips for different applications.
Small Passives/Actives to be removed with thermal tweezers
Automated system for IC and BGA repair (Microscope, Camera, Beam split optics, Computer, Programmer, Heat controllers, Vacuum
system, Laser pointer) Solder Hand-Tool (Adjustable in temperature height, Temperature shall be held constant,Flexible tips)
4.3 Adjust your solder tool so that a temperature around 360 -380 is reached and stabilized at the solder joint.
Heating-time of the solder-joint should not exceed ~ 4 sec. Avoid temperatures above 400 otherwise wear-out of tips will rise drastically
and flux-fluid will be destroyed.Corrosion of Tool-Spikes can be avoided when using SAC305 and a temperature of less than 400 .
4.4 Mix of lead-free solder-tin/parts with leaded soldering-tin/parts is possible but not recommended. If not to avoid clean carefully the
solder-joint from old tin and re-solder with new tin.
4.5 Use only original spare-parts listed in the Service-Manuals. Standard-material(consumables) can also be purchased at external
companies.
4.6 Special information for lead-free BGA-ICs: this ICs will be delivered in so-called dry-packaging to protect the IC against moisture and
with lead-free logo on it. This packaging may only be opened shortly before it is used (soldered). Otherwise the body of the IC gets wet
inside and during the heating time the structure of the IC will be destroyed due to high (steam-)pressure. If the packaging was opened
before usage the IC has to be heated up for some hours (around 90 ) for drying (Take attention for ESD-protection!)
5. Rework on BGA (Ball Grid Array) ICs
General
Although (LF)BGA assembly yields are very high, there may still be a requirement for component rework. By rework, we
mean the process of removing the component from the PWB and replacing it with a new component. If an (LF)BGA is
removed from a PWB, the solder balls of the component are deformed drastically so the removed (LF)BGA has to be
discarded.
Device Removal
As is the case with any component that, it is essential when removing an (LF)BGA, the board, tracks, solder lands, or
surrounding components are not damaged. To remove an (LF)BGA, the board must be uniformly heated to a temperature
close to the reflow soldering temperature. A uniform temperature reduces the chance of warping the PWB.
To do this, we recommend that the board is heated until it is certain that all the joints are molten. Then carefully pull the
component off the board with a vacuum nozzle. For the appropriate temperature profiles, see the IC data sheet.
Area Preparation
When the component has been removed, the vacant IC area must be cleaned before replacing the (LF)BGA.
Removing an IC often leaves varying amounts of solder on the mounting lands. This excessive solder can be removed with
either a solder sucker or solder wick. The remaining flux can be removed with a brush and cleaning agent. After the board
is properly cleaned and inspected, apply flux on the solder lands and on the connection balls of the(LF)BGA
Note: Do not apply solder paste, as this has shown to result in problems during re-soldering.
Device Replacement
The last step in the repair process is to solder the new component on the board. Ideally, the (LF)BGA should be
aligned under a microscope or magnifying glass. If this is not possible, try to align the (LF)BGA with any board markers.
To reflow the solder, apply a temperature profile according to the IC data sheet. So as not to damage neighbouring
components, it may be necessary to reduce some temperatures and times.
More Information
For more information on how to handle BGA devices, visit this URL: http://www.atyourservice.ce.philips.com (needs
subscription). After login, select Magazine , then go to Workshop Information . Here you will find Information on how
.to deal with BGA-ICs.
Repair Flow Chart 190CW7 LCD 69
AC IN
Power Board
Control Board Scaler Board
LCD Panel
No power
(power indicator off)
NG
Check 18V/12V/5V Bad power board
OK
NG
Bad Scaler Board Check Scaler Board
OK
Check Control Board OK Check Control Wires
Check LCD Panel

70 190CW7 LCD Repair Flow Chart
NG
Power Board Bad Power Board
OK
OK
OK
Check Scaler Board Bad Scaler Board
OK
OK
Repair Flow Chart 190CW7 LCD 71
18V/12V/5V DC
OK
NO
OK
Check
Power Board
OK
Check LCD Panel
Control Board
OK
OK
Board
72 190CW7 LCD Safety Test Requirements
All units that are returned for service or repair must pass the 3. Equipments and Connection
original manufactures safety tests. Safety testing requires both
Hipot and Ground Continuity testing. 3.1. Equipments
For example :
HI-POT TEST INSTRUCTION - ChenHwa 9032 PROGRAMMABLE AUTO SAFETY
1.Application requirements TESTER
- ChenHwa 510B Digital Grounding Continuity Tester
1.1 All mains operated products must pass the Hi-Pot test as - ChenHwa 901 (AC Hi-pot test), 902 (AC, DC Hi-pot test)
described in this instruction. Withstanding Tester
1.2 This test must be performed again after the covers have
been refitted following the repair, inspection or modification 3.2. Connection
of the product. * Turn on the power switch of monitor before Hipot and
Ground Continuity testing.
2. Test method
2.1 Connecting conditions Clip
2.1.1 The test specified must be applied between the parallel-

blade plug of the mainscord and all accessible metal
parts of the product.
2.1.2 Before carrying out the test, reliable conductive
connections must be ensured and thereafter be
maintained throughout the test period. Clip
2.1.3 The mains switch(es) must be in the "ON" position.
2.2 Test Requirements

All products should be HiPot and Ground Continuity tested as
follows:
Condition HiPot Test for HiPot Test for Ground Continuity

products where products where Test requirement
the mains input the mains input is
range is Full 110V AC(USA
range(or 220V type)
AC)
Test 2820VDC 1700VDC Test current: (ChenHwa 9032 tester)
voltage (2000VAC) (1200VAC) 25A,AC Video cable
Test time:
Test time 3 seconds 1 second 3 seconds(min.)
(min.) Resistance
required:
Trip set at 100 uA 5 mA <=0.09+Rohm, Connect the "video cable"
current for Max. R is the or "grounding screw"
to the CLIP on your tester.
(Tester) limitation; set resistance of
at 0.1 uA for the mains cord.
Min. Limitation
Ramp set at 2
time seconds
(Tester) Grounding screw
2.2.1 The minimum test duration for Quality Control Inspector

must be 1 minute.
Connect the power cord
2.2.2 The test voltage must be maintained within the specified
to the monitor.
voltage + 5%.
2.2.3 There must be no breakdown during the test.
2.2.4 The grounding blade or pin of mains plug must be

conducted with accessible metal parts. Power outlet
4. Recording (Rear view of monitor)
Hipot and Ground Continuity testing records have to be kept

for a period of 10 years.
Recommended Parts List 190CW7 LCD 73
Recommended Parts List
TYPE:190CW7CS/00(CMO)
Item Philips 12NC DESCRIPTION TPV 18NC

9965 000 39710 BASE 034G1844VB1B
9965 000 39714 POWER LENS A33G00601C
9965 000 39715 FRONT BEZEL PHILIPS A34G0112VOA2T
9965 000 39716 KEY BUTTON A33G0067VO1T
9965 000 39717 REAR COVER A34G0051VB1T
9965 000 39718 STAND TOP A34G0053VB1B
9965 000 39719 STAND BOTTOM A34G0054VB1B
9965 000 39720 HINGE A37G00071
IC801 9965 000 36059 0Z9938 056G60810
IC901 9965 000 39747 LD7575PS SOP-8 056G37961
IC902 9965 000 36055 PC123Y22FZOF 056G1393A
IC903 9965 000 36054 KIA431A-AT/P TO-92 056G15812
U401 9965 000 41346 MCU ASSY 705GP9K056005
U403 9965 000 41345 EEPROM ASSY 705GP9K056006
U404 9965 000 35965 M24C02-WMN6TP 056G113334
U405 9965 000 35965 M24C02-WMN6TP 056G113334
U701 9965 000 37095 AIC1084-33PM 056G5637
U702 9965 000 35963 AI1117D-1.8-EI 056G56331
74 190CW7 LCD Spare Parts List
Model: 190CW7CS/00(CMO) 12NC: 8639 000 17256 C447 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R 065G060310412
C448 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R 065G060310412
C449 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R 065G060310412
C450 9965 000 38992 CHIP 1UF 16V X7R 0603 065G060310512
C454 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R 065G060310412
Mechanical Parts
C455 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R 065G060310412
C456 9965 000 36917 CHIP 1000PF 50V NPO 065G060310231
9965 000 39710 BASE 034G1844VB1B
C457 9965 000 36917 CHIP 1000PF 50V NPO 065G060310231
9965 000 39714 POWER LENS A33G00601C
C458 9965 000 36917 CHIP 1000PF 50V NPO 065G060310231
9965 000 39715 FRONT BEZEL PHILIPS A34G0112VOA2T
C459 9965 000 36917 CHIP 1000PF 50V NPO 065G060310231
9965 000 39716 KEY BUTTON A33G0067VO1T
C460 9965 000 36917 CHIP 1000PF 50V NPO 065G060310231
9965 000 39717 REAR COVER A34G0051VB1T
C461 9965 000 36917 CHIP 1000PF 50V NPO 065G060310231
9965 000 39718 STAND TOP A34G0053VB1B
C462 9965 000 36917 CHIP 1000PF 50V NPO 065G060310231
9965 000 39719 STAND BOTTOM A34G0054VB1B
C463 9965 000 36917 CHIP 1000PF 50V NPO 065G060310231
9965 000 39720 HINGE A37G00071
C464 9965 000 36917 CHIP 1000PF 50V NPO 065G060310231
C465 9965 000 36917 CHIP 1000PF 50V NPO 065G060310231
Accessory
C466 9965 000 36917 CHIP 1000PF 50V NPO 065G060310231
C467 9965 000 36917 CHIP 1000PF 50V NPO 065G060310231
9965 000 35910 POWER CORD 089G404A18NLS
C468 9965 000 36917 CHIP 1000PF 50V NPO 065G060310231
C469 9965 000 36917 CHIP 1000PF 50V NPO 065G060310231
miscellanea
C470 9965 000 37517 1000PF -10% 50V X7R 065G060310232
C701 9965 000 37517 1000PF -10% 50V X7R 065G060310232
9965 000 39709 RUBBER 012G62161
C702 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R 065G060310412
9965 000 39711 SIGNAL CABLE 089G728GAA901
C703 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R 065G060310412
9965 000 39712 FFC CABLE 30P 205MM P1.0 089G179E30C7
C704 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R 065G060310412
C705 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R 065G060310412
LCD Panel
C706 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R 065G060310412
C707 9965 000 35958 KY25VB100M-L 6.3*11 067G215L1014N
9965 000 39713 PANEL LCD 19" A1-L02 CMO 750GLM90A1211N
C708 9965 000 35958 KY25VB100M-L 6.3*11 067G215L1014N
C709 9965 000 35958 KY25VB100M-L 6.3*11 067G215L1014N
PCB Assy
C710 9965 000 35958 KY25VB100M-L 6.3*11 067G215L1014N
C711 9965 000 35958 KY25VB100M-L 6.3*11 067G215L1014N
9965 000 39721 CONVERSION BOARD CBPC6MNNPHA
C712 9965 000 35958 KY25VB100M-L 6.3*11 067G215L1014N
9965 000 39722 KEY BOARD KEPC6AP1
9965 000 39723 POWER BOARD ASSY PWPC942MR1P
R401 9965 000 35971 CHIPR 10K OHM -5% 1/16W 061L0603103
R402 9965 000 35971 CHIPR 10K OHM -5% 1/16W 061L0603103
PCB Assy
R403 9965 000 35972 RST SM 0603 RC0603 100K PM5 R 061L0603104
9965 000 39721 CONVERSION BOARD CBPC6MNNPHA
R404 9965 000 35972 RST SM 0603 RC0603 100K PM5 R 061L0603104
Various
R405 9965 000 35969 CHIPR 100 OHM -5% 1/16W 061L0603101
CN202 9965 000 39725 DVID CONN 24P FEMALE 90 DVR024 088G35424FHGP R406 9965 000 35969 CHIPR 100 OHM -5% 1/16W 061L0603101
CN405 9965 000 35960 D-SUB 15PIN 088G35315FH R407 9965 000 35969 CHIPR 100 OHM -5% 1/16W 061L0603101
CN406 9965 000 36924 FPC CONN. 1.0MM 30P 033G801930FH R408 9965 000 35969 CHIPR 100 OHM -5% 1/16W 061L0603101
R410 9965 000 36002 RST SM 0603 JUMP MAX 0R05 R 061L0603000
C401 9965 000 36917 CHIP 1000PF 50V NPO 065G060310231 R411 9965 000 36002 RST SM 0603 JUMP MAX 0R05 R 061L0603000
C402 9965 000 36917 CHIP 1000PF 50V NPO 065G060310231 R414 9965 000 35972 RST SM 0603 RC0603 100K PM5 R 061L0603104
C403 9965 000 36921 CHIP 0.047UF 50V X7R 065G060347332 R415 9965 000 35971 CHIPR 10K OHM -5% 1/16W 061L0603103
C404 9965 000 36921 CHIP 0.047UF 50V X7R 065G060347332 R416 9965 000 36002 RST SM 0603 JUMP MAX 0R05 R 061L0603000
C409 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R 065G060310412 R421 9965 000 35974 CHIPR 150 OHM -5% 1/16W 061L0603151
C410 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R 065G060310412 R422 9965 000 35970 CHIPR 1K OHM -5% 1/16W 061L0603102
C412 9965 000 37324 CAP:CER 0.22UF-20%-80% 10V SM 065G060322417 R424 9965 000 35974 CHIPR 150 OHM -5% 1/16W 061L0603151
C420 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R 065G060310412 R434 9965 000 35973 RST SM 0603 RC0603 1M PM5 R 061L0603105
C421 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R 065G060310412 R435 9965 000 35977 CHIPR 2.2K OHM -5% 1/16W 061L0603222
C426 9965 000 36922 KY16VB470M-L 10*12.5 067G215L4713N R441 9965 000 35969 CHIPR 100 OHM -5% 1/16W 061L0603101
C427 9965 000 36919 CER1 0603 NP0 50V 22P PM5 R 065G060322031 R442 9965 000 35978 CHIP 3.3K OHM 1/10W 061L0603332
C428 9965 000 36919 CER1 0603 NP0 50V 22P PM5 R 065G060322031 R443 9965 000 35978 CHIP 3.3K OHM 1/10W 061L0603332
C429 9965 000 36916 CHIP 10PF -0.5PF 50V NPO 065G060310031 R444 9965 000 36068 CHIP 150OHM 1/4W 061L1206151
C430 9965 000 36919 CER1 0603 NP0 50V 22P PM5 R 065G060322031 R445 9965 000 37788 CHIP 390 OHM 1/10W 061L0603391
C431 9965 000 36923 KY25VB47-M-CC3.0 5*11MM 067G215V4704N R446 9965 000 35971 CHIPR 10K OHM -5% 1/16W 061L0603103
C432 9965 000 35959 LOW ESR EC 4.7 UF 50V NCC 067G215Y4797N R447 9965 000 35981 CHIPR 4.7K OHM -5% 1/16W 061L0603472
C436 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R 065G060310412 R450 9965 000 36002 RST SM 0603 JUMP MAX 0R05 R 061L0603000
C443 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R 065G060310412 R457 9965 000 36002 RST SM 0603 JUMP MAX 0R05 R 061L0603000
Spare Parts List 190CW7 LCD 75
R461 9965 000 36002 RST SM 0603 JUMP MAX 0R05 R 061L0603000 ZD414 9965 000 35996 UDZS5.6B 093G39S34T
R463 9965 000 36002 RST SM 0603 JUMP MAX 0R05 R 061L0603000 Q401 9965 000 35966 PMBS3904/PHILIPS-SMT(04) 057G4174
R464 9965 000 36002 RST SM 0603 JUMP MAX 0R05 R 061L0603000 Q402 9965 000 12957 TR PNP PMBS3906 SOT23(PHILIPS) 057G4176
R465 9965 000 36002 RST SM 0603 JUMP MAX 0R05 R 061L0603000 Q404 9965 000 12957 TR PNP PMBS3906 SOT23(PHILIPS) 057G4176
R466 9965 000 36002 RST SM 0603 JUMP MAX 0R05 R 061L0603000 Q405 9965 000 35968 A03401 SOT23 BY AOS(A1) 057G7631
R467 9965 000 36002 RST SM 0603 JUMP MAX 0R05 R 061L0603000 Q406 9965 000 35966 PMBS3904/PHILIPS-SMT(04) 057G4174
R468 9965 000 36002 RST SM 0603 JUMP MAX 0R05 R 061L0603000 U401 9965 000 41346 MCU ASSY 705GP9K056005
R469 9965 000 35971 CHIPR 10K OHM -5% 1/16W 061L0603103 U403 9965 000 41345 EEPROM ASSY 705GP9K056006
R470 9965 000 35970 CHIPR 1K OHM -5% 1/16W 061L0603102 U404 9965 000 35965 M24C02-WMN6TP 056G113334
R471 9965 000 37788 CHIP 390 OHM 1/10W 061L0603391 U405 9965 000 35965 M24C02-WMN6TP 056G113334
R472 9965 000 35971 CHIPR 10K OHM -5% 1/16W 061L0603103 U701 9965 000 37095 AIC1084-33PM 056G5637
R473 9965 000 36068 CHIP 150OHM 1/4W 061L1206151 U702 9965 000 35963 AI1117D-1.8-EI 056G56331
R476 9965 000 35971 CHIPR 10K OHM -5% 1/16W 061L0603103
R478 9965 000 35981 CHIPR 4.7K OHM -5% 1/16W 061L0603472
R479 9965 000 35981 CHIPR 4.7K OHM -5% 1/16W 061L0603472 PCB Assy
R480 9965 000 35981 CHIPR 4.7K OHM -5% 1/16W 061L0603472 2490 9965 000 39722 KEY BOARD KEPC6AP1
R481 9965 000 35981 CHIPR 4.7K OHM -5% 1/16W 061L0603472 Various
R484 9965 000 36003 RST SM 0603 RC0603 47K PM5 R 061L0603473 CN101 9965 000 39726 PIN HEADER 2*6 R/A 033G802712H
R486 9965 000 36002 RST SM 0603 JUMP MAX 0R05 R 061L0603000 SW1 9965 000 36000 TACT SWITCH TSPB-2 -NP 077G6001GCJ
R488 9965 000 35969 CHIPR 100 OHM -5% 1/16W 061L0603101 SW3 9965 000 36000 TACT SWITCH TSPB-2 -NP 077G6001GCJ
R489 9965 000 35969 CHIPR 100 OHM -5% 1/16W 061L0603101 SW4 9965 000 36000 TACT SWITCH TSPB-2 -NP 077G6001GCJ
R496 9965 000 35970 CHIPR 1K OHM -5% 1/16W 061L0603102 C101 9965 000 36004 0.01UF -10% 50V X7R 065G060310332
R497 9965 000 35970 CHIPR 1K OHM -5% 1/16W 061L0603102 C102 9965 000 36004 0.01UF -10% 50V X7R 065G060310332
R499 9965 000 36002 RST SM 0603 JUMP MAX 0R05 R 061L0603000 C103 9965 000 36004 0.01UF -10% 50V X7R 065G060310332
R701 9965 000 35980 CHIPR 47 OHM -5% 1/16W 061L0603470 C104 9965 000 36004 0.01UF -10% 50V X7R 065G060310332
C105 9965 000 36004 0.01UF -10% 50V X7R 065G060310332
FB401 9965 000 36934 071G59B300K
FB402 9965 000 36002 RST SM 0603 JUMP MAX 0R05 R 061L0603000 R105 9965 000 35970 CHIPR 1K OHM -5% 1/16W 061L0603102
FB403 9965 000 36934 071G59B300K R106 9965 000 35971 CHIPR 10K OHM -5% 1/16W 061L0603103
FB404 9965 000 36934 071G59B300K R107 9965 000 35970 CHIPR 1K OHM -5% 1/16W 061L0603102
FB405 9965 000 36002 RST SM 0603 JUMP MAX 0R05 R 061L0603000 R108 9965 000 35971 CHIPR 10K OHM -5% 1/16W 061L0603103
FB406 9965 000 36002 RST SM 0603 JUMP MAX 0R05 R 061L0603000 R109 9965 000 35969 CHIPR 100 OHM -5% 1/16W 061L0603101
FB407 9965 000 37332 B201209D102TT 071G56D102
FB408 9965 000 35993 CHIP BEAD 071G56K121 D101 9965 000 39727 LED GP32032C-R03-ZY-HB 081G121GGP
FB410 9965 000 35993 CHIP BEAD 071G56K121
FB411 9965 000 35993 CHIP BEAD 071G56K121 PCB Assy
FB412 9965 000 35993 CHIP BEAD 071G56K121 2670 9965 000 39723 POWER BOARD ASSY PWPC942MR1P
FB413 9965 000 35993 CHIP BEAD 071G56K121 Various
FB414 9965 000 35993 CHIP BEAD 071G56K121 F901 9965 000 39741 FUSE 3.15A 250V MET3.15 084G557
FB415 9965 000 36933 CHIP BEAD 120 OHM 0603FBM-11-1 071G59B121K F901 9965 000 36046 1.5MM RIVET 006G31502
FB416 9965 000 36933 CHIP BEAD 120 OHM 0603FBM-11-1 071G59B121K NR901 9965 000 36046 1.5MM RIVET 006G31502
FB417 9965 000 36933 CHIP BEAD 120 OHM 0603FBM-11-1 071G59B121K PT801 9965 000 36093 X'FMR DARFONTK.2006M.101 080GL19T8DN1
FB418 9965 000 36933 CHIP BEAD 120 OHM 0603FBM-11-1 071G59B121K PT801 9965 000 38142 TRANSFORMER ASS'Y S80GL19T8V1
FB419 9965 000 36933 CHIP BEAD 120 OHM 0603FBM-11-1 071G59B121K PT801 9965 000 36046 1.5MM RIVET 006G31502
FB420 9965 000 36933 CHIP BEAD 120 OHM 0603FBM-11-1 071G59B121K PT802 9965 000 36093 X'FMR DARFONTK.2006M.101 080GL19T8DN1
FB701 9965 000 35993 CHIP BEAD 071G56K121 PT802 9965 000 38142 TRANSFORMER ASS'Y S80GL19T8V1
FB702 9965 000 35993 CHIP BEAD 071G56K121 PT802 9965 000 36046 1.5MM RIVET 006G31502
FB703 9965 000 35993 CHIP BEAD 071G56K121 Q903 9965 000 36046 1.5MM RIVET 006G31502
FB704 9965 000 35993 CHIP BEAD 071G56K121 T901 9965 000 39739 XFMR FOR POWER LITAI 080GL17T37LGP
FB707 9965 000 35993 CHIP BEAD 071G56K121
T901 9965 000 39740 XFMR FOR POWER LISHIN 080GL17T37LSGP
X401 9965 000 35961 CRYSTAL 12MHZ HC-49US ARG6-120 093G2251
T901 9965 000 36046 1.5MM RIVET 006G31502
D404 9965 000 35994 DIO SIG SM BAV99 (PHSE)R 093G6433

C801 9965 000 36041 CHIP 0.1U 50V X7R 065G080510432
C804 9965 000 36073 CHIP 1UF 25V X7R 0805 065G080510522
C805 9965 000 36991 1000PF 50V NPO 065G080510231
C806 9965 000 36073 CHIP 1UF 25V X7R 0805 065G080510522
C807 9965 000 39768 10NF/50V/0805/X7R 065G080510332
C809 9965 000 39770 CHIP 0.022UF 50V X7R 0805 065G080522332
C810 9965 000 36044 CHIP 470PF 50V NPO 065G080547131
C811 9965 000 36007 ED 470UF 25V 067G215D4714K
C811 9965 000 39732 470UF 25V 067G215L4714H
C812 9965 000 39773 CHIP 1000PF 500V X7R 065G120610272
C813 9965 000 39773 CHIP 1000PF 500V X7R 065G120610272
C814 9965 000 39771 CHIP CAP 0.22 UF 25V X7R 065G080522422
D416 9965 000 35995 BAV70 SOT-23 093G6442PP
C815 9965 000 36007 ED 470UF 25V 067G215D4714K
D417 9965 000 35995 BAV70 SOT-23 093G6442PP
C815 9965 000 39732 470UF 25V 067G215L4714H
D701 9965 000 36935 FA20-04 093G20403F
C816 9965 000 39729 22PF 5% SL 3KV TDK 065G3J2206ET
D702 9965 000 36935 FA20-04 093G20403F
C818 9965 000 39772 3200PF/25V/X7R 065G080533232
ZD401 9965 000 35996 UDZS5.6B 093G39S34T
C819 9965 000 36045 CHIP 0.047UF 50V X7R 065G080547332
ZD402 9965 000 35996 UDZS5.6B 093G39S34T
C820 9965 000 36044 CHIP 470PF 50V NPO 065G080547131
ZD403 9965 000 35996 UDZS5.6B 093G39S34T
C822 9965 000 39773 CHIP 1000PF 500V X7R 065G120610272
ZD404 9965 000 35996 UDZS5.6B 093G39S34T
C823 9965 000 39773 CHIP 1000PF 500V X7R 065G120610272
ZD405 9965 000 35996 UDZS5.6B 093G39S34T
C824 9965 000 36941 5PF 5% SL 3KV 065G3J5096ET
ZD406 9965 000 35996 UDZS5.6B 093G39S34T
C825 9965 000 36941 5PF 5% SL 3KV 065G3J5096ET
ZD407 9965 000 35996 UDZS5.6B 093G39S34T
C826 9965 000 36941 5PF 5% SL 3KV 065G3J5096ET
ZD408 9965 000 35996 UDZS5.6B 093G39S34T
C827 9965 000 39772 3200PF/25V/X7R 065G080533232
ZD409 9965 000 35996 UDZS5.6B 093G39S34T
C828 9965 000 36041 CHIP 0.1U 50V X7R 065G080510432
ZD410 9965 000 35996 UDZS5.6B 093G39S34T
C829 9965 000 36041 CHIP 0.1U 50V X7R 065G080510432
ZD411 9965 000 35996 UDZS5.6B 093G39S34T
C831 9965 000 36044 CHIP 470PF 50V NPO 065G080547131
ZD412 9965 000 35996 UDZS5.6B 093G39S34T
C834 9965 000 39729 22PF 5% SL 3KV TDK 065G3J2206ET
ZD413 9965 000 35996 UDZS5.6B 093G39S34T
C835 9965 000 36941 5PF 5% SL 3KV 065G3J5096ET
76 190CW7 LCD Spare Parts List
C837 9965 000 39729 22PF 5% SL 3KV TDK 065G3J2206ET R830 9965 000 39761 CHIP 82KOHM 1/8W 061L0805823
C838 9965 000 36041 CHIP 0.1U 50V X7R 065G080510432 R831 9965 000 36981 CHIP 7.5K OHM 1/10W 061L0805752
C839 9965 000 36041 CHIP 0.1U 50V X7R 065G080510432 R832 9965 000 36083 MGFR 6.2MOHM -5% 1/2W 061G212Y625KT
C840 9965 000 36073 CHIP 1UF 25V X7R 0805 065G080510522 R836 9965 000 36963 CHIPR 1K OHM -5% 1/10W 061L0805102
C841 9965 000 39729 22PF 5% SL 3KV TDK 065G3J2206ET R837 9965 000 39767 CHIPR 5.1OHM -5% 1/4W 061L1206519
C842 9965 000 36041 CHIP 0.1U 50V X7R 065G080510432 R841 9965 000 39750 RST CHIPR 560 OHM -1% 1/8W 061G08055600F
C843 9965 000 36041 CHIP 0.1U 50V X7R 065G080510432 R842 9965 000 39767 CHIPR 5.1OHM -5% 1/4W 061L1206519
C844 9965 000 36041 CHIP 0.1U 50V X7R 065G080510432 R843 9965 000 36963 CHIPR 1K OHM -5% 1/10W 061L0805102
C845 9965 000 36991 1000PF 50V NPO 065G080510231 R846 9965 000 36013 CHIP 1M OHM 5% 1/8W 061L0805105
C900 9965 000 39731 2200PF -20% 250VAC 065G306M2222BM R850 9965 000 39755 CHIRP 4.7K OHM -5% 1/10W 061L0805472
C901 9965 000 39730 Y1.CAP.001UF 250VAC MURATA 065G306M1022BM R851 9965 000 36986 CHIP 4.7KOHM 5% 1/4W 061L1206472
C902 9965 000 39730 Y1.CAP.001UF 250VAC MURATA 065G306M1022BM R852 9965 000 39755 CHIRP 4.7K OHM -5% 1/10W 061L0805472
C903 9965 000 37794 FILM CAPACITOR 063G10747410S R853 9965 000 39755 CHIRP 4.7K OHM -5% 1/10W 061L0805472
C904 9965 000 36007 ED 470UF 25V 067G215D4714K R858 9965 000 39759 750 OHM 061L0805751
C904 9965 000 39732 470UF 25V 067G215L4714H R860 9965 000 36013 CHIP 1M OHM 5% 1/8W 061L0805105
C905 9965 000 36051 100UF 450V 18*36 105 BY HERMEI 067G215S10115H R901 9965 000 36024 CHIPR 680K OHM -5% 1/8W 061L1206684
C905 9965 000 36086 100UF 450V 067G215S10115K R902 9965 000 36024 CHIPR 680K OHM -5% 1/8W 061L1206684
C905 9965 000 36046 1.5MM RIVET 006G31502 R903 9965 000 36024 CHIPR 680K OHM -5% 1/8W 061L1206684
C906 9965 000 39781 KY50VB10M-TP5 5*11.5 067G2151007NT R904 9965 000 39766 RST CHIPR 3.9KOHM -5% 1/4W 061L1206392
C907 9965 000 39781 KY50VB10M-TP5 5*11.5 067G2151007NT R905 9965 000 36010 100K OHM 5% 2W 061G152M10458F
C908 9965 000 39774 CHIP 0.1UF 25V X7R 1206 065G120610432 R906 9965 000 36022 CHIP 100 OHM 5% 1/8W 061L1206101
C909 9965 000 39769 220PF 50V NPO 065G080522131 R909 9965 000 39765 CHIP 3.3OHM 1/4W 061L1206339
C910 9965 000 36044 CHIP 470PF 50V NPO 065G080547131 R910 9965 000 39764 CHIP 22OHM 5% 8W 061L1206220
C911 9965 000 36007 ED 470UF 25V 067G215D4714K R911 9965 000 39762 CHIP 1K OHM 5% 1/8W 061L1206102
C911 9965 000 39732 470UF 25V 067G215L4714H R912 9965 000 36964 CHIPR 10K OHM -5% 1/10W 061L0805103
C912 9965 000 36007 ED 470UF 25V 067G215D4714K R913 9965 000 36965 CHIPR 100K OHM -5% 1/10W 061L0805104
C912 9965 000 39732 470UF 25V 067G215L4714H R914 9965 000 39744 RST MOFR 0.47OHM -5% 2WS 061G152M47858F
C916 9965 000 36041 CHIP 0.1U 50V X7R 065G080510432 R916 9965 000 36022 CHIP 100 OHM 5% 1/8W 061L1206101
C917 9965 000 36041 CHIP 0.1U 50V X7R 065G080510432 R919 9965 000 36070 CHIPR 470 OHM -5% 1/8W 061L1206471
C930 9965 000 39780 CERAMIC CAP 065G2K1521TGP R922 9965 000 36963 CHIPR 1K OHM -5% 1/10W 061L0805102
C931 9965 000 39780 CERAMIC CAP 065G2K1521TGP R923 9965 000 36975 CHIP 33KOHM 1/8W 1% 061L08053302F
C932 9965 000 39780 CERAMIC CAP 065G2K1521TGP R924 9965 000 36142 CHIPR 2.4KOHM -1% 1/8W 061L08052401F
C933 9965 000 39780 CERAMIC CAP 065G2K1521TGP R925 9965 000 39753 CHIP 3.6KOHM 1/8W 1% 061L08053601F
C934 9965 000 39780 CERAMIC CAP 065G2K1521TGP R926 9965 000 36971 CHIP 2KOHM 1/8W 061L0805202
C935 9965 000 36007 ED 470UF 25V 067G215D4714K R927 9965 000 36016 CHIP 10KOHM 5% 1/4W 061L1206103
C935 9965 000 39732 470UF 25V 067G215L4714H R931 9965 000 39766 RST CHIPR 3.9KOHM -5% 1/4W 061L1206392
C936 9965 000 36007 ED 470UF 25V 067G215D4714K R934 9965 000 36022 CHIP 100 OHM 5% 1/8W 061L1206101
C936 9965 000 39732 470UF 25V 067G215L4714H R935 9965 000 36022 CHIP 100 OHM 5% 1/8W 061L1206101
C937 9965 000 36007 ED 470UF 25V 067G215D4714K R936 9965 000 36022 CHIP 100 OHM 5% 1/8W 061L1206101
C937 9965 000 39732 470UF 25V 067G215L4714H R937 9965 000 36022 CHIP 100 OHM 5% 1/8W 061L1206101
R938 9965 000 39766 RST CHIPR 3.9KOHM -5% 1/4W 061L1206392
C808 9965 000 39752 180K OHM 1/8W 061L0805184
F902 9965 000 39751 0 OHM 1/8W 061G1206000 FB901 9965 000 39733 FERRITE BEAD 071G5529GP
F903 9965 000 39751 0 OHM 1/8W 061G1206000 L901 9965 000 39737 CHOKE 073L17453LGGP
JR801 9965 000 35984 CHIPR 0OHM -5% 1/10W 061L0805000 L901 9965 000 39738 CHOKE BY LISHIN 073L17453LSGGP
JR803 9965 000 36067 CHIPR 0 OHM -5% 1/8W 061L1206000 L901 9965 000 36046 1.5MM RIVET 006G31502
JR804 9965 000 35984 CHIPR 0OHM -5% 1/10W 061L0805000 L902 9965 000 36088 LINE FILTER 073G17465H
JR805 9965 000 35984 CHIPR 0OHM -5% 1/10W 061L0805000 L902 9965 000 36025 LINE FILTER BY LISHIN 073G17465LS
JR806 9965 000 36067 CHIPR 0 OHM -5% 1/8W 061L1206000 L902 9965 000 39227 TRANSFORMERS S73G17465VW
JR807 9965 000 35984 CHIPR 0OHM -5% 1/10W 061L0805000 L902 9965 000 36046 1.5MM RIVET 006G31502
JR808 9965 000 36067 CHIPR 0 OHM -5% 1/8W 061L1206000 L903 9965 000 39734 CHOKE 073G25391T
JR809 9965 000 36067 CHIPR 0 OHM -5% 1/8W 061L1206000 L903 9965 000 39736 CHOKE BY LI SHIN 073G25391LSGP
JR901 9965 000 36067 CHIPR 0 OHM -5% 1/8W 061L1206000 L904 9965 000 39734 CHOKE 073G25391T
JR902 9965 000 36067 CHIPR 0 OHM -5% 1/8W 061L1206000 L904 9965 000 39735 CHOKE BY LI SHIN 073G25391LS
NR901 9965 000 39728 8 OHM NCT 061G58080WT
R801 9965 000 39749 100K 0805 061G0805104 BD901 9965 000 39742 BRIDGE DIODE KBP208G LITEON 093G5046028
R802 9965 000 36063 300K OM 1/8W 061L0805304 D801 9965 000 35994 DIO SIG SM BAV99 (PHSE)R 093G6433
R803 9965 000 36964 CHIPR 10K OHM -5% 1/10W 061L0805103 D802 9965 000 35994 DIO SIG SM BAV99 (PHSE)R 093G6433
R805 9965 000 36070 CHIPR 470 OHM -5% 1/8W 061L1206471 D804 9965 000 35994 DIO SIG SM BAV99 (PHSE)R 093G6433
R807 9965 000 39764 CHIP 22OHM 5% 8W 061L1206220 D806 9965 000 35994 DIO SIG SM BAV99 (PHSE)R 093G6433
R808 9965 000 39756 CHIPR 47K OHM -5% 1/8W 061L0805473 D809 9965 000 39779 IN4148W 093G64S511SEM
R810 9965 000 36013 CHIP 1M OHM 5% 1/8W 061L0805105 D810 9965 000 39779 IN4148W 093G64S511SEM
R813 9965 000 36013 CHIP 1M OHM 5% 1/8W 061L0805105 D812 9965 000 39779 IN4148W 093G64S511SEM
R815 9965 000 36965 CHIPR 100K OHM -5% 1/10W 061L0805104 D901 9965 000 36030 RECTIFIER DIODE FR107 093G6026T52T
R816 9965 000 36013 CHIP 1M OHM 5% 1/8W 061L0805105 D902 9965 000 36095 FR103 093G6038T52T
R817 9965 000 39754 SMD 39KOHM/0805/ -5% 1/8W 061L0805393 D903 9965 000 39775 LL4148-GS08 093G6432V
R818 9965 000 39763 CHIP 15 OHM 5% 1206 1/4W 061L1206150 D904 9965 000 39775 LL4148-GS08 093G6432V
R819 9965 000 39763 CHIP 15 OHM 5% 1206 1/4W 061L1206150 D908 9965 000 39745 SP20150 093G60252
R822 9965 000 36083 MGFR 6.2MOHM -5% 1/2W 061G212Y625KT D908 9965 000 39746 DIODE SP20150R ITO-220 SECOS 093G60281
R823 9965 000 39761 CHIP 82KOHM 1/8W 061L0805823 D909 9965 000 39745 SP20150 093G60252
R824 9965 000 39759 750 OHM 061L0805751 D909 9965 000 39746 DIODE SP20150R ITO-220 SECOS 093G60281
R825 9965 000 39758 CHIP 51KOHM 1/8W 061L0805513 ZD801 9965 000 36079 RLZ 5.6B LLDS 093G39S24T
R826 9965 000 39757 CHIP 510 OHM 1% 1/8W 061L08055100F ZD901 9965 000 39777 RLZ 13B LLDS 093G39S40T
R827 9965 000 36981 CHIP 7.5K OHM 1/10W 061L0805752 ZD902 9965 000 36079 RLZ 5.6B LLDS 093G39S24T
R828 9965 000 39763 CHIP 15 OHM 5% 1206 1/4W 061L1206150 ZD903 9965 000 36080 PTZ 9.1B 093G39S38T
R829 9965 000 39763 CHIP 15 OHM 5% 1206 1/4W 061L1206150 ZD904 9965 000 39778 RLZ18B LLDS 093G39S44T
Spare Parts List 190CW7 LCD 77
ZD905 9965 000 39776 RLZ20B LLDS 093G39S12T
IC801 9965 000 36059 0Z9938 056G60810

IC901 9965 000 39747 LD7575PS SOP-8 056G37961
IC902 9965 000 36055 PC123Y22FZOF 056G1393A
IC903 9965 000 36054 KIA431A-AT/P TO-92 056G15812
Q801 9965 000 35966 PMBS3904/PHILIPS-SMT(04) 057G4174
Q804 9965 000 36033 RK7002 057G7592
Q805 9965 000 39748 AO4828L 057G7636
Q805 9965 000 36100 AM9945N 057G76314
Q806 9965 000 39748 AO4828L 057G7636
Q806 9965 000 36100 AM9945N 057G76314
Q807 9965 000 36033 RK7002 057G7592
Q808 9965 000 36033 RK7002 057G7592
Q809 9965 000 36033 RK7002 057G7592
Q810 9965 000 36033 RK7002 057G7592
Q903 9965 000 39743 STP10NK70ZFP 057G66721
78 190CW7 LCD Different Parts List
Diversity of 190CW7CS/27(CMO) compared with 190CW7CS/00(CMO) 810 061L0603102 CHIPR 1K OHM -5% 1/16W 9965 000 35970
820 061L0603102 CHIPR 1K OHM -5% 1/16W 9965 000 35970
890 061L0603103 CHIPR 10K OHM -5% 1/16W 9965 000 35971
Item Philips 12NC DESCRIPTION TPV 18NC 900 061L0603103 CHIPR 10K OHM -5% 1/16W 9965 000 35971
8639 000 17262 190CW7CS/27 910 061L0603103 CHIPR 10K OHM -5% 1/16W 9965 000 35971
9965 000 41575 MAINSCORD 089G402A18NLS2 920 061L0603103 CHIPR 10K OHM -5% 1/16W 9965 000 35971
9965 000 41537 MAIN FRAME ASSY CMO 705GZ-000036 930 061L0603103 CHIPR 10K OHM -5% 1/16W 9965 000 35971
9965 000 41572 REAR COVER ASSY 705GZ-000037 1000 061L0603104 RST SM 0603 RC0603 100K PM5 R 9965 000 35972
9965 000 41573 FRONT BEZEL ASSY HP CMO 705GZ-000038 1010 061L0603104 RST SM 0603 RC0603 100K PM5 R 9965 000 35972
9965 000 41538 MAIN FRAME CMO A15G00322 1020 061L0603104 RST SM 0603 RC0603 100K PM5 R 9965 000 35972
1030 061L0603105 RST SM 0603 RC0603 1M PM5 R 9965 000 35973
1040 061L0603151 CHIPR 150 OHM -5% 1/16W 9965 000 35974
1050 061L0603151 CHIPR 150 OHM -5% 1/16W 9965 000 35974
Diversity of 190CW7CS/69(CMO) compared with 190CW7CS/00(CMO) 1060 061L0603151 CHIPR 150 OHM -5% 1/16W 9965 000 35974
1070 061L0603222 CHIPR 2.2K OHM -5% 1/16W 9965 000 35977
1080 061L0603222 CHIPR 2.2K OHM -5% 1/16W 9965 000 35977
Item Philips 12NC DESCRIPTION TPV 18NC 1090 061L0603332 CHIP 3.3K OHM 1/10W 9965 000 35978
8639 000 17257 190CW7CS/69 1100 061L0603332 CHIP 3.3K OHM 1/10W 9965 000 35978
9965 000 41057 POWER CORD 1.8M PY8B1V6CC0A-060 089G410A18NLSB 1110 061L0603391 CHIP 390 OHM 1/10W 9965 000 37788
9965 000 41537 MAIN FRAME ASSY CMO 705GZ-000036 1120 061L0603470 CHIPR 47 OHM -5% 1/16W 9965 000 35980
9965 000 41572 REAR COVER ASSY 705GZ-000037 1130 061L0603472 CHIPR 4.7K OHM -5% 1/16W 9965 000 35981
9965 000 41573 FRONT BEZEL ASSY HP CMO 705GZ-000038 1140 061L0603472 CHIPR 4.7K OHM -5% 1/16W 9965 000 35981
9965 000 41538 MAIN FRAME CMO A15G00322 1150 061L0603472 CHIPR 4.7K OHM -5% 1/16W 9965 000 35981
1160 061L0603472 CHIPR 4.7K OHM -5% 1/16W 9965 000 35981
1170 061L0603473 RST SM 0603 RC0603 47K PM5 R 9965 000 36003
1180 061L0603750 CHIPR 75 OHM -5% 1/16W 9965 000 35982
Diversity of 190CW7CS/93(CMO) compared with 190CW7CS/00(CMO) 1190 061L0603750 CHIPR 75 OHM -5% 1/16W 9965 000 35982
1200 061L0603750 CHIPR 75 OHM -5% 1/16W 9965 000 35982
1210 061L1206151 CHIP 150OHM 1/4W 9965 000 36068
1220 061L1206151 CHIP 150OHM 1/4W 9965 000 36068
8639 000 17259 190CW7CS/93 1230 065G060310031 CHIP 10PF -0.5PF 50V NPO 9965 000 36916
9965 000 41562 MAINSCORD CCEE 10A 1M8 DET BK 089G414A18NLSC 1240 065G060310231 CHIP 1000PF 50V NPO 9965 000 36917
9965 000 41537 MAIN FRAME ASSY CMO 705GZ-000036 1250 065G060310231 CHIP 1000PF 50V NPO 9965 000 36917
9965 000 41572 REAR COVER ASSY 705GZ-000037 1260 065G060310231 CHIP 1000PF 50V NPO 9965 000 36917
9965 000 41573 FRONT BEZEL ASSY HP CMO 705GZ-000038 1270 065G060310231 CHIP 1000PF 50V NPO 9965 000 36917
9965 000 41712 EPS(L) Q44G90441 1280 065G060310231 CHIP 1000PF 50V NPO 9965 000 36917
9965 000 41713 EPS(R) Q44G90442 1290 065G060310231 CHIP 1000PF 50V NPO 9965 000 36917
9965 000 41714 CARTON (/93) Z44G90018131A 1300 065G060310231 CHIP 1000PF 50V NPO 9965 000 36917
1310 065G060310231 CHIP 1000PF 50V NPO 9965 000 36917
9965 000 41538 MAIN FRAME CMO A15G00322
1320 065G060310231 CHIP 1000PF 50V NPO 9965 000 36917
1330 065G060310232 1000PF -10% 50V X7R 9965 000 37517
Diversity of 190WV7CS/00(CMO) compared with 190CW7CS/00(CMO) 1340 065G060310232 1000PF -10% 50V X7R 9965 000 37517
Item TPV 18NC Description Philips 12NC 1350 065G060310412 CER2 0603 X7R 16V 100N PM10 R 9965 000 36918
10 034G1844VB1B BASE 9965 000 39710 1360 065G060310412 CER2 0603 X7R 16V 100N PM10 R 9965 000 36918
20 089G728GAA901 SIGNAL CABLE 9965 000 39711 1370 065G060310412 CER2 0603 X7R 16V 100N PM10 R 9965 000 36918
30 089G179E30C7 FFC CABLE 30P 205MM P1.0 9965 000 39712 1380 065G060310412 CER2 0603 X7R 16V 100N PM10 R 9965 000 36918
40 705GZV15002 MAIN FRAME ASSY CMO 9965 000 43701 1390 065G060310412 CER2 0603 X7R 16V 100N PM10 R 9965 000 36918
60 705GZV34001 REAR COVER ASSY 9965 000 43702 1400 065G060310412 CER2 0603 X7R 16V 100N PM10 R 9965 000 36918
90 705GZV34002 FRONT BEZEL ASSY 9965 000 43703 1410 065G060310412 CER2 0603 X7R 16V 100N PM10 R 9965 000 36918
130 750GLM90A1211N PANEL LCD 19" A1-L02 CMO 9965 000 39713 1420 065G060310412 CER2 0603 X7R 16V 100N PM10 R 9965 000 36918
140 A34G0053VB1B STAND TOP 9965 000 39718 1430 065G060310412 CER2 0603 X7R 16V 100N PM10 R 9965 000 36918
150 A34G0054VB1B STAND BOTTOM 9965 000 39719 1440 065G060310412 CER2 0603 X7R 16V 100N PM10 R 9965 000 36918
160 A37G00071 HINGE 9965 000 39720 1450 065G060310412 CER2 0603 X7R 16V 100N PM10 R 9965 000 36918
240 089G420A18NIS1 MAINS CORD TWN 7A 1M8 BK 9965 000 43167 1460 065G060310412 CER2 0603 X7R 16V 100N PM10 R 9965 000 36918
260 CBPC6MNNPZSA1 SCALER?ASSEMBLY 9965 000 43704 1470 065G060310412 CER2 0603 X7R 16V 100N PM10 R 9965 000 36918
2150 KEPC6AP1 KEY BOARD 9965 000 39722 1480 065G060310412 CER2 0603 X7R 16V 100N PM10 R 9965 000 36918
2320 PWPC942MR1P POWER BOARD ASSY 9965 000 39723 1490 065G060310412 CER2 0603 X7R 16V 100N PM10 R 9965 000 36918
50 Z15G00021 MAIN FRAME CMO 9965 000 43705 1500 065G060310412 CER2 0603 X7R 16V 100N PM10 R 9965 000 36918
100 A33G00601C POWER LENS 9965 000 39714 1600 065G060310512 CHIP 1UF 16V X7R 0603 9965 000 38992
110 A33G0067VO1T KEY BUTTON 9965 000 39716 1610 065G060322031 CER1 0603 NP0 50V 22P PM5 R 9965 000 36919
120 A34G0112VOA2T FRONT BEZEL PHILIPS 9965 000 39715 1620 065G060322031 CER1 0603 NP0 50V 22P PM5 R 9965 000 36919
280 033G801930FH FPC CONN. 1.0MM 30P 9965 000 36924 1630 065G060322031 CER1 0603 NP0 50V 22P PM5 R 9965 000 36919
290 067G3151014K EC 100UF 25V EG1E101MNN0511PU 6. 9965 000 43645 1640 065G060322417 CAP:CER 0.22UF-20%-80% 10V SM 9965 000 37324
300 067G3151014K EC 100UF 25V EG1E101MNN0511PU 6. 9965 000 43645 1650 065G060347332 CHIP 0.047UF 50V X7R 9965 000 36921
350 067G3154704K EC 47UF 25V EG1E470MNN0511PU 5*1 9965 000 43647 1700 065G060347332 CHIP 0.047UF 50V X7R 9965 000 36921
360 067G3154797K 5*11MM 9965 000 43648 1710 071G56D102 B201209D102TT 9965 000 37332
370 067G215L1014N KY25VB100M-L 6.3*11 9965 000 35958 1720 071G56D102M CHIP HEAD 1000OHM 9965 000 43649
380 067G215L1014N KY25VB100M-L 6.3*11 9965 000 35958 1730 071G56K121 CHIP BEAD 9965 000 35993
420 067G215L4713N KY16VB470M-L 10*12.5 9965 000 36922 1770 071G56K121 CHIP BEAD 9965 000 35993
430 067G215S4713K EC 470UF 16V 9965 000 43646 1780 071G56K121 CHIP BEAD 9965 000 35993
440 067G215V4704N KY25VB47-M-CC3.0 5*11MM 9965 000 36923 1790 071G56K121 CHIP BEAD 9965 000 35993
450 067G215Y4797N LOW ESR EC 4.7 UF 50V NCC 9965 000 35959 1800 071G56K121 CHIP BEAD 9965 000 35993
460 088G35315FH D-SUB 15PIN 9965 000 35960 1810 071G56K121M CHIP BEAD 9965 000 36567
470 093G2251 CRYSTAL 12MHZ HC-49US ARG6-120 9965 000 35961 1820 071G56K121M CHIP BEAD 9965 000 36567
480 056G5637 AIC1084-33PM 9965 000 37095 1830 071G56K121M CHIP BEAD 9965 000 36567
490 056G56321 AP1084K33LA 9965 000 37330 1840 071G56K121M CHIP BEAD 9965 000 36567
500 056G56331 AI1117D-1.8-EI 9965 000 35963 1850 071G56K121M CHIP BEAD 9965 000 36567
510 056G113324 AT24C16AN-10SU-2.7 9965 000 35964 1860 071G56K121M CHIP BEAD 9965 000 36567
520 056G113333 M24C16-MN6TP 9965 000 39724 1870 071G56K121M CHIP BEAD 9965 000 36567
530 056G113334 M24C02-WMN6TP 9965 000 35965 1880 071G56K121M CHIP BEAD 9965 000 36567
540 057G4174 PMBS3904/PHILIPS-SMT(04) 9965 000 35966
550 057G4174 PMBS3904/PHILIPS-SMT(04) 9965 000 35966 1890 071G59B300K 9965 000 36934
560 057G4176 TR PNP PMBS3906 SOT23(PHILIPS) 9965 000 12957 1900 071G59B300K 9965 000 36934
570 057G4176 TR PNP PMBS3906 SOT23(PHILIPS) 9965 000 12957 1910 071G59B300K 9965 000 36934
580 057G7631 A03401 SOT23 BY AOS(A1) 9965 000 35968 1920 071G59B300M CHIP BEAD 30 OHM 9965 000 43707
690 061L0603101 CHIPR 100 OHM -5% 1/16W 9965 000 35969 1930 071G59B300M CHIP BEAD 30 OHM 9965 000 43707
800 061L0603102 CHIPR 1K OHM -5% 1/16W 9965 000 35970 1940 071G59B300M CHIP BEAD 30 OHM 9965 000 43707
Different Parts List 190CW7 LCD 79
1950 093G6433 DIO SIG SM BAV99 (PHSE)R 9965 000 35994 3600 057G4174 PMBS3904/PHILIPS-SMT(04) 9965 000 35966
1960 093G6433 DIO SIG SM BAV99 (PHSE)R 9965 000 35994 3610 057G7592 RK7002 9965 000 36033
1990 093G6442PP BAV70 SOT-23 9965 000 35995 3640 057G7592 RK7002 9965 000 36033
2000 093G39S34T UDZS5.6B 9965 000 35996 3650 057G7592 RK7002 9965 000 36033
2010 093G39S34T UDZS5.6B 9965 000 35996 3660 057G7636 AO4828L 9965 000 39748
2020 093G39S34T UDZS5.6B 9965 000 35996 3670 057G7636 AO4828L 9965 000 39748
2030 093G39S34T UDZS5.6B 9965 000 35996 3680 057G76314 AM9945N 9965 000 36100
2040 093G39S34T UDZS5.6B 9965 000 35996 3690 057G76314 AM9945N 9965 000 36100
2050 093G39S34T UDZS5.6B 9965 000 35996 3700 061G0805104 100K 0805 9965 000 39749
2060 093G39S34T UDZS5.6B 9965 000 35996 3710 061G08055600F RST CHIPR 560 OHM -1% 1/8W 9965 000 39750
2070 093G39S34T UDZS5.6B 9965 000 35996 3720 061G1206000 0 OHM 1/8W 9965 000 39751
2080 093G39S34T UDZS5.6B 9965 000 35996 3730 061G1206000 0 OHM 1/8W 9965 000 39751
2090 093G20403F FA20-04 9965 000 36935 3740 061L0805000 CHIPR 0OHM -5% 1/10W 9965 000 35984
2100 093G20403F FA20-04 9965 000 36935 3750 061L0805000 CHIPR 0OHM -5% 1/10W 9965 000 35984
2110 705GZV56017 CPU ASSEMBLY 9965 000 43708 3760 061L0805000 CHIPR 0OHM -5% 1/10W 9965 000 35984
2120 056G562117 IC NT68663MEFG-128 QFP-128L NOVA 9965 000 37779 3770 061L0805000 CHIPR 0OHM -5% 1/10W 9965 000 35984
2840 081G121GGP LED GP32032C-R03-ZY-HB 9965 000 39727 3780 061L0805102 CHIPR 1K OHM -5% 1/10W 9965 000 36963
2850 077G6001GCJ TACT SWITCH TSPB-2 -NP 9965 000 36000 3790 061L0805102 CHIPR 1K OHM -5% 1/10W 9965 000 36963
2900 061L0603101 CHIPR 100 OHM -5% 1/16W 9965 000 35969 3840 061L0805103 CHIPR 10K OHM -5% 1/10W 9965 000 36964
2910 061L0603102 CHIPR 1K OHM -5% 1/16W 9965 000 35970 3850 061L0805103 CHIPR 10K OHM -5% 1/10W 9965 000 36964
3860 061L0805103 CHIPR 10K OHM -5% 1/10W 9965 000 36964
2920 061L0603102 CHIPR 1K OHM -5% 1/16W 9965 000 35970
3870 061L0805103 CHIPR 10K OHM -5% 1/10W 9965 000 36964
2930 061L0603103 CHIPR 10K OHM -5% 1/16W 9965 000 35971
3880 061L0805104 CHIPR 100K OHM -5% 1/10W 9965 000 36965
2940 061L0603103 CHIPR 10K OHM -5% 1/16W 9965 000 35971
3890 061L0805104 CHIPR 100K OHM -5% 1/10W 9965 000 36965
2950 065G060310332 0.01UF -10% 50V X7R 9965 000 36004
3900 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013
2960 065G060310332 0.01UF -10% 50V X7R 9965 000 36004
3910 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013
2970 065G060310332 0.01UF -10% 50V X7R 9965 000 36004
3920 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013
2980 065G060310332 0.01UF -10% 50V X7R 9965 000 36004
3930 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013
2990 065G060310332 0.01UF -10% 50V X7R 9965 000 36004
3940 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013
3010 063G10747410S FILM CAPACITOR 9965 000 37794
3950 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013
3020 067G215D4714K ED 470UF 25V 9965 000 36007
3960 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013
3030 067G215D4714K ED 470UF 25V 9965 000 36007
3970 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013
3040 067G215D4714K ED 470UF 25V 9965 000 36007
3980 061L0805184 180K OHM 1/8W 9965 000 39752
3050 067G215D4714K ED 470UF 25V 9965 000 36007
3990 061L0805202 CHIP 2KOHM 1/8W 9965 000 36971
3060 067G215D4714K ED 470UF 25V 9965 000 36007 4000 061L08052401F CHIPR 2.4KOHM -1% 1/8W 9965 000 36142
3070 067G215D4714K ED 470UF 25V 9965 000 36007 4010 061L0805304 300K OM 1/8W 9965 000 36063
3080 067G215D4714K ED 470UF 25V 9965 000 36007 4020 061L08053302F CHIP 33KOHM 1/8W 1% 9965 000 36975
3090 067G215D4714K ED 470UF 25V 9965 000 36007 4030 061L08053601F CHIP 3.6KOHM 1/8W 1% 9965 000 39753
3100 067G215L4714H 470UF 25V 9965 000 39732 4040 061L0805393 SMD 39KOHM/0805/ -5% 1/8W 9965 000 39754
3110 067G215L4714H 470UF 25V 9965 000 39732 4050 061L0805472 CHIRP 4.7K OHM -5% 1/10W 9965 000 39755
3140 067G215L4714H 470UF 25V 9965 000 39732 4080 061L0805473 CHIPR 47K OHM -5% 1/8W 9965 000 39756
3150 067G215L4714H 470UF 25V 9965 000 39732 4090 061L08055100F CHIP 510 OHM 1% 1/8W 9965 000 39757
3160 067G215L4714H 470UF 25V 9965 000 39732 4100 061L0805513 CHIP 51KOHM 1/8W 9965 000 39758
3170 067G215L4714H 470UF 25V 9965 000 39732 4110 061L0805751 750 OHM 9965 000 39759
3180 067G215S10115H 100UF 450V 18*36 105 BY HERMEI 9965 000 36051 4120 061L0805751 750 OHM 9965 000 39759
3190 067G215S10115K 100UF 450V 9965 000 36086 4130 061L0805752 CHIP 7.5K OHM 1/10W 9965 000 36981
3200 084G557 FUSE 3.15A 250V MET3.15 9965 000 39741 4140 061L0805752 CHIP 7.5K OHM 1/10W 9965 000 36981
3210 093G5046028 BRIDGE DIODE KBP208G LITEON 9965 000 39742 4150 061L0805754 CHIPR 750K OHM -5% 1/8W 9965 000 39760
3220 056G1393A PC123Y22FZOF 9965 000 36055 4160 061L0805823 CHIP 82KOHM 1/8W 9965 000 39761
3230 061G58080WT 8 OHM NCT 9965 000 39728 4170 061L0805823 CHIP 82KOHM 1/8W 9965 000 39761
3240 065G3J2206EM 22PF 3KV 9965 000 43644 4180 061L1206000 CHIPR 0 OHM -5% 1/8W 9965 000 36067
3250 065G3J2206EM 22PF 3KV 9965 000 43644 4190 061L1206000 CHIPR 0 OHM -5% 1/8W 9965 000 36067
3260 065G3J2206ET 22PF 5% SL 3KV TDK 9965 000 39729 4200 061L1206000 CHIPR 0 OHM -5% 1/8W 9965 000 36067
3300 065G3J5096ET 5PF 5% SL 3KV 9965 000 36941 4240 061L1206101 CHIP 100 OHM 5% 1/8W 9965 000 36022
3340 065G306M1022BM Y1.CAP.001UF 250VAC MURATA 9965 000 39730 4280 061L1206101 CHIP 100 OHM 5% 1/8W 9965 000 36022
3360 065G306M2222BM 2200PF -20% 250VAC 9965 000 39731 4300 061L1206102 CHIP 1K OHM 5% 1/8W 9965 000 39762
3370 073G17465H LINE FILTER 9965 000 36088 4310 061L1206103 CHIP 10KOHM 5% 1/4W 9965 000 36016
3380 073G17465LS LINE FILTER BY LISHIN 9965 000 36025 4320 061L1206150 CHIP 15 OHM 5% 1206 1/4W 9965 000 39763
3390 073G25391T CHOKE 9965 000 39734 4330 061L1206150 CHIP 15 OHM 5% 1206 1/4W 9965 000 39763
3410 073G25391LS CHOKE BY LI SHIN 9965 000 39735 4350 061L1206150 CHIP 15 OHM 5% 1206 1/4W 9965 000 39763
3420 073G25391LSGP CHOKE BY LI SHIN 9965 000 39736 4360 061L1206220 CHIP 22OHM 5% 8W 9965 000 39764
3430 073L17453LGGP CHOKE 9965 000 39737 4370 061L1206220 CHIP 22OHM 5% 8W 9965 000 39764
3440 073L17453LSGGP CHOKE BY LISHIN 9965 000 39738 4380 061L1206339 CHIP 3.3OHM 1/4W 9965 000 39765
3450 080GL17T37LGP XFMR FOR POWER LITAI 9965 000 39739 4390 061L1206392 RST CHIPR 3.9KOHM -5% 1/4W 9965 000 39766
3460 080GL17T37LSGP XFMR FOR POWER LISHIN 9965 000 39740 4400 061L1206392 RST CHIPR 3.9KOHM -5% 1/4W 9965 000 39766
3470 080GL19T8DN1 X'FMR DARFONTK.2006M.101 9965 000 36093 4410 061L1206392 RST CHIPR 3.9KOHM -5% 1/4W 9965 000 39766
3480 080GL19T8DN1 X'FMR DARFONTK.2006M.101 9965 000 36093 4420 061L1206471 CHIPR 470 OHM -5% 1/8W 9965 000 36070
3490 057G66721 STP10NK70ZFP 9965 000 39743 4430 061L1206471 CHIPR 470 OHM -5% 1/8W 9965 000 36070
3500 061G152M10458F 100K OHM 5% 2W 9965 000 36010 4440 061L1206472 CHIP 4.7KOHM 5% 1/4W 9965 000 36986
3510 061G152M47858F RST MOFR 0.47OHM -5% 2WS 9965 000 39744 4450 061L1206519 CHIPR 5.1OHM -5% 1/4W 9965 000 39767
3520 093G60252 SP20150 9965 000 39745 4460 061L1206519 CHIPR 5.1OHM -5% 1/4W 9965 000 39767
3530 093G60281 DIODE SP20150R ITO-220 SECOS 9965 000 39746 4470 061L1206684 CHIPR 680K OHM -5% 1/8W 9965 000 36024
3540 093G60252 SP20150 9965 000 39745 4480 061L1206684 CHIPR 680K OHM -5% 1/8W 9965 000 36024
3550 093G60281 DIODE SP20150R ITO-220 SECOS 9965 000 39746 4490 061L1206684 CHIPR 680K OHM -5% 1/8W 9965 000 36024
3560 056G37961 LD7575PS SOP-8 9965 000 39747 4500 065G2K1521TGP CERAMIC CAP 9965 000 39780
3570 056G60810 0Z9938 9965 000 36059 4510 065G2K1521TGP CERAMIC CAP 9965 000 39780
3580 057G4174 PMBS3904/PHILIPS-SMT(04) 9965 000 35966 4520 065G2K1521TGP CERAMIC CAP 9965 000 39780
3590 057G4174 PMBS3904/PHILIPS-SMT(04) 9965 000 35966 4530 065G2K1521TGP CERAMIC CAP 9965 000 39780
4540 065G2K1521TGP CERAMIC CAP 9965 000 39780
3550 093G60281 DIODE SP20150R ITO-220 SECOS 9965 000 39746

Diversity of 190CW7CB/69(CMO) compared with 190CW7CS/00(CMO) 3560 056G37961 LD7575PS SOP-8 9965 000 39747
3570 056G60810 0Z9938 9965 000 36059
Item TPV 18NC Description Philips 12NC
10 089G728GAA901 SIGNAL CABLE 9965 000 39711
20 089G179E30C7 FFC CABLE 30P 205MM P1.0 9965 000 39712
30 089G410A18NLSB POWER CORD 1.8M PY8B1V6CC0A-060 9965 000 41057
3610 057G7592 RK7002 9965 000 36033
40 705GZ-000036 MAIN FRAME ASSY CMO 9965 000 41537
3620 057G7592 RK7002 9965 000 36033
60 705GZV34003 FRONT BEZEL ASSY 9965 000 43715
3630 057G7592 RK7002 9965 000 36033
110 705GZV34004 REAR COVER ASSY 9965 000 43716
3640 057G7592 RK7002 9965 000 36033
130 750GLM90A1211N PANEL LCD 19" A1-L02 CMO 9965 000 39713
3650 057G7592 RK7002 9965 000 36033
210 Z34G0022WV1B STAND TOP 9965 000 43718
3660 057G7636 AO4828L 9965 000 39748
220 Z34G0023WV1B STAND BOTTOM 9965 000 43719
3670 057G7636 AO4828L 9965 000 39748
230 A37G00071 HINGE 9965 000 39720
3680 057G76314 AM9945N 9965 000 36100
240 Z34G0024WV1B BASE 9965 000 43717
3690 057G76314 AM9945N 9965 000 36100
250 CBPC6MNNPHSB4 CONVERSATION BOARD 9965 000 43523
3700 061G0805104 100K 0805 9965 000 39749
2830 KEPC6AP1 KEY BOARD 9965 000 39722
3710 061G08055600F RST CHIPR 560 OHM -1% 1/8W 9965 000 39750
3000 PWPC942MR1P POWER BOARD ASSY 9965 000 39723
3720 061G1206000 0 OHM 1/8W 9965 000 39751
90 A34G0051VB1T REAR COVER 9965 000 39717
3730 061G1206000 0 OHM 1/8W 9965 000 39751
60 A15G00322 MAIN FRAME CMO 9965 000 41538
3740 061L0805000 CHIPR 0OHM -5% 1/10W 9965 000 35984
90 Z33G0019WV1T KEY BUTTON 9965 000 43720
3750 061L0805000 CHIPR 0OHM -5% 1/10W 9965 000 35984
100 Z34G0020WVA2T FRONT BEZEL PHILIPS 9965 000 43721
3760 061L0805000 CHIPR 0OHM -5% 1/10W 9965 000 35984
1 705GZ9K056001 CPU ASSY 9965 000 43518
3770 061L0805000 CHIPR 0OHM -5% 1/10W 9965 000 35984
2840 081G121GGP LED GP32032C-R03-ZY-HB 9965 000 39727
3780 061L0805102 CHIPR 1K OHM -5% 1/10W 9965 000 36963
2850 077G6001GCJ TACT SWITCH TSPB-2 -NP 9965 000 36000
3790 061L0805102 CHIPR 1K OHM -5% 1/10W 9965 000 36963
3800 061L0805102 CHIPR 1K OHM -5% 1/10W 9965 000 36963
3810 061L0805102 CHIPR 1K OHM -5% 1/10W 9965 000 36963
3820 061L0805102 CHIPR 1K OHM -5% 1/10W 9965 000 36963
3830 061L0805103 CHIPR 10K OHM -5% 1/10W 9965 000 36964
2900 061L0603101 CHIPR 100 OHM -5% 1/16W 9965 000 35969
3840 061L0805103 CHIPR 10K OHM -5% 1/10W 9965 000 36964
2910 061L0603102 CHIPR 1K OHM -5% 1/16W 9965 000 35970
3850 061L0805103 CHIPR 10K OHM -5% 1/10W 9965 000 36964
2920 061L0603102 CHIPR 1K OHM -5% 1/16W 9965 000 35970
3860 061L0805103 CHIPR 10K OHM -5% 1/10W 9965 000 36964
2930 061L0603103 CHIPR 10K OHM -5% 1/16W 9965 000 35971
3870 061L0805103 CHIPR 10K OHM -5% 1/10W 9965 000 36964
2940 061L0603103 CHIPR 10K OHM -5% 1/16W 9965 000 35971
3880 061L0805104 CHIPR 100K OHM -5% 1/10W 9965 000 36965
2950 065G060310332 0.01UF -10% 50V X7R 9965 000 36004
3890 061L0805104 CHIPR 100K OHM -5% 1/10W 9965 000 36965
2960 065G060310332 0.01UF -10% 50V X7R 9965 000 36004
3900 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013
2970 065G060310332 0.01UF -10% 50V X7R 9965 000 36004
3910 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013
2980 065G060310332 0.01UF -10% 50V X7R 9965 000 36004
3920 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013
2990 065G060310332 0.01UF -10% 50V X7R 9965 000 36004
3930 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013
3010 063G10747410S FILM CAPACITOR 9965 000 37794
3940 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013
3020 067G215D4714K ED 470UF 25V 9965 000 36007
3950 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013
3030 067G215D4714K ED 470UF 25V 9965 000 36007
3960 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013
3040 067G215D4714K ED 470UF 25V 9965 000 36007
3970 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013
3050 067G215D4714K ED 470UF 25V 9965 000 36007
3980 061L0805184 180K OHM 1/8W 9965 000 39752
3060 067G215D4714K ED 470UF 25V 9965 000 36007
3990 061L0805202 CHIP 2KOHM 1/8W 9965 000 36971
3070 067G215D4714K ED 470UF 25V 9965 000 36007
4000 061L08052401F CHIPR 2.4KOHM -1% 1/8W 9965 000 36142
3080 067G215D4714K ED 470UF 25V 9965 000 36007
4010 061L0805304 300K OM 1/8W 9965 000 36063
3090 067G215D4714K ED 470UF 25V 9965 000 36007
4020 061L08053302F CHIP 33KOHM 1/8W 1% 9965 000 36975
3100 067G215L4714H 470UF 25V 9965 000 39732
4030 061L08053601F CHIP 3.6KOHM 1/8W 1% 9965 000 39753
3110 067G215L4714H 470UF 25V 9965 000 39732
4040 061L0805393 SMD 39KOHM/0805/ -5% 1/8W 9965 000 39754
3120 067G215L4714H 470UF 25V 9965 000 39732
4050 061L0805472 CHIRP 4.7K OHM -5% 1/10W 9965 000 39755
3130 067G215L4714H 470UF 25V 9965 000 39732
4060 061L0805472 CHIRP 4.7K OHM -5% 1/10W 9965 000 39755
3140 067G215L4714H 470UF 25V 9965 000 39732
4070 061L0805472 CHIRP 4.7K OHM -5% 1/10W 9965 000 39755
3150 067G215L4714H 470UF 25V 9965 000 39732
3160 067G215L4714H 470UF 25V 9965 000 39732
4080 061L0805473 CHIPR 47K OHM -5% 1/8W 9965 000 39756
3170 067G215L4714H 470UF 25V 9965 000 39732 4090 061L08055100F CHIP 510 OHM 1% 1/8W 9965 000 39757
3180 067G215S10115H 100UF 450V 18*36 105 BY HERMEI 9965 000 36051 4100 061L0805513 CHIP 51KOHM 1/8W 9965 000 39758
3190 067G215S10115K 100UF 450V 9965 000 36086 4110 061L0805751 750 OHM 9965 000 39759
3200 084G557 FUSE 3.15A 250V MET3.15 9965 000 39741 4120 061L0805751 750 OHM 9965 000 39759
3210 093G5046028 BRIDGE DIODE KBP208G LITEON 9965 000 39742 4130 061L0805752 CHIP 7.5K OHM 1/10W 9965 000 36981
3220 056G1393A PC123Y22FZOF 9965 000 36055 4140 061L0805752 CHIP 7.5K OHM 1/10W 9965 000 36981
3230 061G58080WT 8 OHM NCT 9965 000 39728 4150 061L0805754 CHIPR 750K OHM -5% 1/8W 9965 000 39760
3240 065G3J2206EM 22PF 3KV 9965 000 43644 4160 061L0805823 CHIP 82KOHM 1/8W 9965 000 39761
3250 065G3J2206EM 22PF 3KV 9965 000 43644 4170 061L0805823 CHIP 82KOHM 1/8W 9965 000 39761
3300 065G3J5096ET 5PF 5% SL 3KV 9965 000 36941 4220 061L1206000 CHIPR 0 OHM -5% 1/8W 9965 000 36067
3310 065G3J5096ET 5PF 5% SL 3KV 9965 000 36941 4230 061L1206000 CHIPR 0 OHM -5% 1/8W 9965 000 36067
3360 065G306M2222BM 2200PF -20% 250VAC 9965 000 39731 4280 061L1206101 CHIP 100 OHM 5% 1/8W 9965 000 36022
3370 073G17465H LINE FILTER 9965 000 36088 4290 061L1206101 CHIP 100 OHM 5% 1/8W 9965 000 36022
3380 073G17465LS LINE FILTER BY LISHIN 9965 000 36025 4300 061L1206102 CHIP 1K OHM 5% 1/8W 9965 000 39762
3390 073G25391T CHOKE 9965 000 39734 4310 061L1206103 CHIP 10KOHM 5% 1/4W 9965 000 36016
3410 073G25391LS CHOKE BY LI SHIN 9965 000 39735 4330 061L1206150 CHIP 15 OHM 5% 1206 1/4W 9965 000 39763
3420 073G25391LSGP CHOKE BY LI SHIN 9965 000 39736 4340 061L1206150 CHIP 15 OHM 5% 1206 1/4W 9965 000 39763
3430 073L17453LGGP CHOKE 9965 000 39737 4350 061L1206150 CHIP 15 OHM 5% 1206 1/4W 9965 000 39763
3440 073L17453LSGGP CHOKE BY LISHIN 9965 000 39738 4360 061L1206220 CHIP 22OHM 5% 8W 9965 000 39764
3450 080GL17T37LGP XFMR FOR POWER LITAI 9965 000 39739 4370 061L1206220 CHIP 22OHM 5% 8W 9965 000 39764
3460 080GL17T37LSGP XFMR FOR POWER LISHIN 9965 000 39740 4380 061L1206339 CHIP 3.3OHM 1/4W 9965 000 39765
3490 057G66721 STP10NK70ZFP 9965 000 39743 4410 061L1206392 RST CHIPR 3.9KOHM -5% 1/4W 9965 000 39766
3500 061G152M10458F 100K OHM 5% 2W 9965 000 36010 4420 061L1206471 CHIPR 470 OHM -5% 1/8W 9965 000 36070
3510 061G152M47858F RST MOFR 0.47OHM -5% 2WS 9965 000 39744 4430 061L1206471 CHIPR 470 OHM -5% 1/8W 9965 000 36070
4440 061L1206472 CHIP 4.7KOHM 5% 1/4W 9965 000 36986
3520 093G60252 SP20150 9965 000 39745
4450 061L1206519 CHIPR 5.1OHM -5% 1/4W 9965 000 39767
3530 093G60281 DIODE SP20150R ITO-220 SECOS 9965 000 39746
4460 061L1206519 CHIPR 5.1OHM -5% 1/4W 9965 000 39767
3540 093G60252 SP20150 9965 000 39745
4470 061L1206684 CHIPR 680K OHM -5% 1/8W 9965 000 36024
4480 061L1206684 CHIPR 680K OHM -5% 1/8W 9965 000 36024 2900 061L0603101 CHIPR 100 OHM -5% 1/16W 9965 000 35969
4490 061L1206684 CHIPR 680K OHM -5% 1/8W 9965 000 36024 2910 061L0603102 CHIPR 1K OHM -5% 1/16W 9965 000 35970
4500 065G2K1521TGP CERAMIC CAP 9965 000 39780 2920 061L0603102 CHIPR 1K OHM -5% 1/16W 9965 000 35970
4530 065G2K1521TGP CERAMIC CAP 9965 000 39780 2950 065G060310332 0.01UF -10% 50V X7R 9965 000 36004
4540 065G2K1521TGP CERAMIC CAP 9965 000 39780 2960 065G060310332 0.01UF -10% 50V X7R 9965 000 36004
4550 065G080510231 1000PF 50V NPO 9965 000 36991 2970 065G060310332 0.01UF -10% 50V X7R 9965 000 36004
4560 065G080510231 1000PF 50V NPO 9965 000 36991 2980 065G060310332 0.01UF -10% 50V X7R 9965 000 36004
4570 065G080510231 1000PF 50V NPO 9965 000 36991 2990 065G060310332 0.01UF -10% 50V X7R 9965 000 36004
4580 065G080510231 1000PF 50V NPO 9965 000 36991 3010 063G10747410S FILM CAPACITOR 9965 000 37794
4590 065G080510231 1000PF 50V NPO 9965 000 36991 3020 067G215D4714K ED 470UF 25V 9965 000 36007
4600 065G080510332 10NF/50V/0805/X7R 9965 000 39768 3030 067G215D4714K ED 470UF 25V 9965 000 36007
4610 065G080510432 CHIP 0.1U 50V X7R 9965 000 36041 3040 067G215D4714K ED 470UF 25V 9965 000 36007
4670 065G080510432 CHIP 0.1U 50V X7R 9965 000 36041 3100 067G215L4714H 470UF 25V 9965 000 39732
4730 065G080510522 CHIP 1UF 25V X7R 0805 9965 000 36073 3160 067G215L4714H 470UF 25V 9965 000 39732
4740 065G080510522 CHIP 1UF 25V X7R 0805 9965 000 36073 3170 067G215L4714H 470UF 25V 9965 000 39732
4750 065G080510522 CHIP 1UF 25V X7R 0805 9965 000 36073 3180 067G215S10115H 100UF 450V 18*36 105 BY HERMEI 9965 000 36051
4760 065G080522131 220PF 50V NPO 9965 000 39769 3190 067G215S10115K 100UF 450V 9965 000 36086
4770 065G080522332 CHIP 0.022UF 50V X7R 0805 9965 000 39770 3200 084G557 FUSE 3.15A 250V MET3.15 9965 000 39741
4780 065G080522422 CHIP CAP 0.22 UF 25V X7R 9965 000 39771 3210 093G5046028 BRIDGE DIODE KBP208G LITEON 9965 000 39742
4790 065G080533232 3200PF/25V/X7R 9965 000 39772 3220 056G1393A PC123Y22FZOF 9965 000 36055
4800 065G080533232 3200PF/25V/X7R 9965 000 39772 3230 061G58080WT 8 OHM NCT 9965 000 39728
4810 065G080547131 CHIP 470PF 50V NPO 9965 000 36044 3240 065G3J2206EM 22PF 3KV 9965 000 43644
4820 065G080547131 CHIP 470PF 50V NPO 9965 000 36044 3250 065G3J2206EM 22PF 3KV 9965 000 43644
4830 065G080547131 CHIP 470PF 50V NPO 9965 000 36044 3260 065G3J2206ET 22PF 5% SL 3KV TDK 9965 000 39729
4840 065G080547131 CHIP 470PF 50V NPO 9965 000 36044 3270 065G3J2206ET 22PF 5% SL 3KV TDK 9965 000 39729
4850 065G080547332 CHIP 0.047UF 50V X7R 9965 000 36045 3280 065G3J2206ET 22PF 5% SL 3KV TDK 9965 000 39729
4860 065G120610272 CHIP 1000PF 500V X7R 9965 000 39773 3290 065G3J2206ET 22PF 5% SL 3KV TDK 9965 000 39729
4870 065G120610272 CHIP 1000PF 500V X7R 9965 000 39773 3300 065G3J5096ET 5PF 5% SL 3KV 9965 000 36941
4900 065G120610432 CHIP 0.1UF 25V X7R 1206 9965 000 39774 3330 065G3J5096ET 5PF 5% SL 3KV 9965 000 36941
4930 067G215Y1007KT LOW ESR EC 10UF 50V EG1H100MPN05 9965 000 43652 3340 065G306M1022BM Y1.CAP.001UF 250VAC MURATA 9965 000 39730
4940 067G215Y1007KT LOW ESR EC 10UF 50V EG1H100MPN05 9965 000 43652 3350 065G306M1022BM Y1.CAP.001UF 250VAC MURATA 9965 000 39730
4950 093G6433 DIO SIG SM BAV99 (PHSE)R 9965 000 35994 3360 065G306M2222BM 2200PF -20% 250VAC 9965 000 39731
4960 093G6433 DIO SIG SM BAV99 (PHSE)R 9965 000 35994 3370 073G17465H LINE FILTER 9965 000 36088
4970 093G6433 DIO SIG SM BAV99 (PHSE)R 9965 000 35994 3380 073G17465LS LINE FILTER BY LISHIN 9965 000 36025
4980 093G6433 DIO SIG SM BAV99 (PHSE)R 9965 000 35994 3390 073G25391T CHOKE 9965 000 39734
4990 093G6433 DIO SIG SM BAV99 (PHSE)R 9965 000 35994 3400 073G25391T CHOKE 9965 000 39734
5000 093G6433 DIO SIG SM BAV99 (PHSE)R 9965 000 35994 3410 073G25391LS CHOKE BY LI SHIN 9965 000 39735
5010 093G6432V LL4148-GS08 9965 000 39775 3420 073G25391LSGP CHOKE BY LI SHIN 9965 000 39736
5030 093G39S12T RLZ20B LLDS 9965 000 39776 3430 073L17453LGGP CHOKE 9965 000 39737
5050 093G39S24T RLZ 5.6B LLDS 9965 000 36079 3440 073L17453LSGGP CHOKE BY LISHIN 9965 000 39738
5060 093G39S38T PTZ 9.1B 9965 000 36080 3450 080GL17T37LGP XFMR FOR POWER LITAI 9965 000 39739
5070 093G39S40T RLZ 13B LLDS 9965 000 39777 3460 080GL17T37LSGP XFMR FOR POWER LISHIN 9965 000 39740
5080 093G39S44T RLZ18B LLDS 9965 000 39778 3470 080GL19T8DN1 X'FMR DARFONTK.2006M.101 9965 000 36093
5090 093G64S511SEM IN4148W 9965 000 39779 3480 080GL19T8DN1 X'FMR DARFONTK.2006M.101 9965 000 36093
5140 061G212Y625KT MGFR 6.2MOHM -5% 1/2W 9965 000 36083 3490 057G66721 STP10NK70ZFP 9965 000 39743
5160 071G5529GP FERRITE BEAD 9965 000 39733 3500 061G152M10458F 100K OHM 5% 2W 9965 000 36010
5170 093G6026T52T RECTIFIER DIODE FR107 9965 000 36030 3510 061G152M47858F RST MOFR 0.47OHM -5% 2WS 9965 000 39744
5180 093G6038T52T FR103 9965 000 36095 3520 093G60252 SP20150 9965 000 39745
5190 056G15810T AZ431AZ-AE1 9965 000 36101 3530 093G60281 DIODE SP20150R ITO-220 SECOS 9965 000 39746
5200 056G15812 KIA431A-AT/P TO-92 9965 000 36054 3540 093G60252 SP20150 9965 000 39745
5210 S73G17465VW TRANSFORMERS 9965 000 39227 3550 093G60281 DIODE SP20150R ITO-220 SECOS 9965 000 39746
5220 S80GL19T8V1 TRANSFORMER ASS'Y 9965 000 38142 3560 056G37961 LD7575PS SOP-8 9965 000 39747
3570 056G60810 0Z9938 9965 000 36059
Diversity of 190CW7CB/93(CMO) compared with 190CW7CS/00(CMO) 3580 057G4174 PMBS3904/PHILIPS-SMT(04) 9965 000 35966
Item TPV 18NC Description Philips 12NC 3600 057G4174 PMBS3904/PHILIPS-SMT(04) 9965 000 35966
10 089G728GAA901 SIGNAL CABLE 9965 000 39711 3610 057G7592 RK7002 9965 000 36033
20 089G179E30C7 FFC CABLE 30P 205MM P1.0 9965 000 39712 3620 057G7592 RK7002 9965 000 36033
30 089G414A18NLSC MAINSCORD CCEE 10A 1M8 DET BK 9965 000 41562 3630 057G7592 RK7002 9965 000 36033
40 705GZ-000036 MAIN FRAME ASSY CMO 9965 000 41537 3640 057G7592 RK7002 9965 000 36033
60 705GZV34003 FRONT BEZEL ASSY 9965 000 43715 3650 057G7592 RK7002 9965 000 36033
110 705GZV34004 REAR COVER ASSY 9965 000 43716 3660 057G7636 AO4828L 9965 000 39748
130 750GLM90A1211N PANEL LCD 19" A1-L02 CMO 9965 000 39713 3670 057G7636 AO4828L 9965 000 39748
200 Z34G0022WV1B STAND TOP 9965 000 43718 3680 057G76314 AM9945N 9965 000 36100
210 A37G00071 HINGE 9965 000 39720 3690 057G76314 AM9945N 9965 000 36100
220 Z34G0023WV1B STAND BOTTOM 9965 000 43719 3700 061G0805104 100K 0805 9965 000 39749
230 Z34G0024WV1B BASE 9965 000 43717 3710 061G08055600F RST CHIPR 560 OHM -1% 1/8W 9965 000 39750
250 CBPC6MNNPHSB6 CONVERSATION BOARD 9965 000 43525 3720 061G1206000 0 OHM 1/8W 9965 000 39751
2840 KEPC6AP1 KEY BOARD 9965 000 39722 3730 061G1206000 0 OHM 1/8W 9965 000 39751
3010 PWPC942MR1P POWER BOARD ASSY 9965 000 39723 3740 061L0805000 CHIPR 0OHM -5% 1/10W 9965 000 35984
60 A15G00322 MAIN FRAME CMO 9965 000 41538 3750 061L0805000 CHIPR 0OHM -5% 1/10W 9965 000 35984
90 Z33G0019WV1T KEY BUTTON 9965 000 43720 3760 061L0805000 CHIPR 0OHM -5% 1/10W 9965 000 35984
100 Z34G0020WVA2T FRONT BEZEL PHILIPS 9965 000 43721 3770 061L0805000 CHIPR 0OHM -5% 1/10W 9965 000 35984
1 705GZ9K056004 CPU ASSY 9965 000 43520 3780 061L0805102 CHIPR 1K OHM -5% 1/10W 9965 000 36963
2840 081G121GGP LED GP32032C-R03-ZY-HB 9965 000 39727 3790 061L0805102 CHIPR 1K OHM -5% 1/10W 9965 000 36963
3850 061L0805103 CHIPR 10K OHM -5% 1/10W 9965 000 36964 5090 093G64S511SEM IN4148W 9965 000 39779
3860 061L0805103 CHIPR 10K OHM -5% 1/10W 9965 000 36964 5140 061G212Y625KT MGFR 6.2MOHM -5% 1/2W 9965 000 36083
3870 061L0805103 CHIPR 10K OHM -5% 1/10W 9965 000 36964 5160 071G5529GP FERRITE BEAD 9965 000 39733
3880 061L0805104 CHIPR 100K OHM -5% 1/10W 9965 000 36965 5170 093G6026T52T RECTIFIER DIODE FR107 9965 000 36030
3890 061L0805104 CHIPR 100K OHM -5% 1/10W 9965 000 36965 5180 093G6038T52T FR103 9965 000 36095
3900 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013 5190 056G15810T AZ431AZ-AE1 9965 000 36101
3910 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013 5200 056G15812 KIA431A-AT/P TO-92 9965 000 36054
3920 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013 5210 S73G17465VW TRANSFORMERS 9965 000 39227
3930 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013 5220 S80GL19T8V1 TRANSFORMER ASS'Y 9965 000 38142
3940 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013 067G2151007NT 9965 000 39781
3950 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013 067G2151007NT 9965 000 39781
3960 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013
3970 061L0805105 CHIP 1M OHM 5% 1/8W 9965 000 36013
3980 061L0805184 180K OHM 1/8W 9965 000 39752 Diversity of 190CW7CB/00(CMO) compared with 190CW7CS/00(CMO)
3990 061L0805202 CHIP 2KOHM 1/8W 9965 000 36971 Item TPV 18 nc Description Philips 12NC
4000 061L08052401F CHIPR 2.4KOHM -1% 1/8W 9965 000 36142 705GZ-000036 Main Frame ASSY CMO 9965 000 41537
4010 061L0805304 300K OM 1/8W 9965 000 36063 A15G00322 Main Frame CMO 9965 000 41538
4020 061L08053302F CHIP 33KOHM 1/8W 1% 9965 000 36975
705GZV34003 Front Bezel Assy 9965 000 43715
4030 061L08053601F CHIP 3.6KOHM 1/8W 1% 9965 000 39753
Z33G0019WV1T Key button 9965 000 43720
4040 061L0805393 SMD 39KOHM/0805/ -5% 1/8W 9965 000 39754
4050 061L0805472 CHIRP 4.7K OHM -5% 1/10W 9965 000 39755 Z34G0020WVA2T Front Bezel Philips 9965 000 43721
4060 061L0805472 CHIRP 4.7K OHM -5% 1/10W 9965 000 39755 705GZV34004 Rear Cover Assy 9965 000 43716
4070 061L0805472 CHIRP 4.7K OHM -5% 1/10W 9965 000 39755 Z34G0021WV1T Rear Cover
4080 061L0805473 CHIPR 47K OHM -5% 1/8W 9965 000 39756 Q40G19E81316C RATING LABEL
4090 061L08055100F CHIP 510 OHM 1% 1/8W 9965 000 39757 Q44G90288131C craton
4100 061L0805513 CHIP 51KOHM 1/8W 9965 000 39758 Q44G90341 EPS(L)
4110 061L0805751 750 OHM 9965 000 39759 Q44G90342 EPS(R)
4120 061L0805751 750 OHM 9965 000 39759 Q45G8860614 PE BAG
4130 061L0805752 CHIP 7.5K OHM 1/10W 9965 000 36981 Q45G8860949 EPE COVER
4140 061L0805752 CHIP 7.5K OHM 1/10W 9965 000 36981 Q70G90028131B E-D.F.U
4150 061L0805754 CHIPR 750K OHM -5% 1/8W 9965 000 39760 Z34G0022WV1B Stand Top 9965 000 43718
4160 061L0805823 CHIP 82KOHM 1/8W 9965 000 39761
Z34G0023WV1B Stand Bottom 9965 000 43719
4170 061L0805823 CHIP 82KOHM 1/8W 9965 000 39761
Z34G0024WV1B BASE 9965 000 43717
4180 061L1206000 CHIPR 0 OHM -5% 1/8W 9965 000 36067
4190 061L1206000 CHIPR 0 OHM -5% 1/8W 9965 000 36067
C707 067G3151014K EC 100uF 25V EG1E101MNN0511PU
4200 061L1206000 CHIPR 0 OHM -5% 1/8W 9965 000 36067 C708 067G3151014K EC 100uF 25V EG1E101MNN0511PU
4240 061L1206101 CHIP 100 OHM 5% 1/8W 9965 000 36022 C712 067G3151014K EC 100uF 25V EG1E101MNN0511PU
4250 061L1206101 CHIP 100 OHM 5% 1/8W 9965 000 36022 C431 067G3154704K EC 47uF 25V EG1E470MNN0511PU
4260 061L1206101 CHIP 100 OHM 5% 1/8W 9965 000 36022 C432 067G3154797K EC 4.7uF 50V EG1H4R7MNN0511PU
4270 061L1206101 CHIP 100 OHM 5% 1/8W 9965 000 36022 C426 067G215S4713K EC 470UF 16V
4280 061L1206101 CHIP 100 OHM 5% 1/8W 9965 000 36022 U701 056G56321 AP1084K33LA
4290 061L1206101 CHIP 100 OHM 5% 1/8W 9965 000 36022 U403 056G113324 AT24C16AN-10SU-2.7
4300 061L1206102 CHIP 1K OHM 5% 1/8W 9965 000 39762 FB407 071G56D102M CHIP HEAD 1000OHM
4310 061L1206103 CHIP 10KOHM 5% 1/4W 9965 000 36016
FB704 071G56K121M CHIP BEAD
4320 061L1206150 CHIP 15 OHM 5% 1206 1/4W 9965 000 39763
4330 061L1206150 CHIP 15 OHM 5% 1206 1/4W 9965 000 39763
FB703 071G56K121M CHIP BEAD
4340 061L1206150 CHIP 15 OHM 5% 1206 1/4W 9965 000 39763 FB702 071G56K121M CHIP BEAD
4350 061L1206150 CHIP 15 OHM 5% 1206 1/4W 9965 000 39763 FB707 071G56K121M CHIP BEAD
4360 061L1206220 CHIP 22OHM 5% 8W 9965 000 39764 FB414 071G56K121M CHIP BEAD
4370 061L1206220 CHIP 22OHM 5% 8W 9965 000 39764 FB413 071G56K121M CHIP BEAD
4380 061L1206339 CHIP 3.3OHM 1/4W 9965 000 39765 FB412 071G56K121M CHIP BEAD
4390 061L1206392 RST CHIPR 3.9KOHM -5% 1/4W 9965 000 39766 FB411 071G56K121M CHIP BEAD
4420 061L1206471 CHIPR 470 OHM -5% 1/8W 9965 000 36070 FB420 071G59B121 TB160808B
4430 061L1206471 CHIPR 470 OHM -5% 1/8W 9965 000 36070 FB419 071G59B121 TB160808B
4440 061L1206472 CHIP 4.7KOHM 5% 1/4W 9965 000 36986 FB418 071G59B121 TB160808B
4450 061L1206519 CHIPR 5.1OHM -5% 1/4W 9965 000 39767
FB417 071G59B121 TB160808B
4460 061L1206519 CHIPR 5.1OHM -5% 1/4W 9965 000 39767
FB416 071G59B121 TB160808B
4470 061L1206684 CHIPR 680K OHM -5% 1/8W 9965 000 36024
4480 061L1206684 CHIPR 680K OHM -5% 1/8W 9965 000 36024 FB415 071G59B121 TB160808B
4490 061L1206684 CHIPR 680K OHM -5% 1/8W 9965 000 36024 FB404 071G59B300M CHIP BEAD 30 OHM
4500 065G2K1521TGP CERAMIC CAP 9965 000 39780 FB403 071G59B300M CHIP BEAD 30 OHM
4510 065G2K1521TGP CERAMIC CAP 9965 000 39780 FB401 071G59B300M CHIP BEAD 30 OHM
4520 065G2K1521TGP CERAMIC CAP 9965 000 39780 U401 705GZ9K056002 CPU ASSY 9965 000 43516
4530 065G2K1521TGP CERAMIC CAP 9965 000 39780 056G562117 NT68663 9965 000 37779
4540 065G2K1521TGP CERAMIC CAP 9965 000 39780 Z40G90008132A cpu label
4550 065G080510231 1000PF 50V NPO 9965 000 36991 Z40G90008132AS CPU software
4560 065G080510231 1000PF 50V NPO 9965 000 36991 C816 065G3J2206EM CAP FOR HIGHT VOLTAGE 9965 000 43644
4570 065G080510231 1000PF 50V NPO 9965 000 36991 C841 065G3J2206EM CAP FOR HIGHT VOLTAGE 9965 000 43644
4580 065G080510231 1000PF 50V NPO 9965 000 36991 C906 067G215Y1007KT KY50VB10M-TP5 5*11.5 9965 000 43652
4590 065G080510231 1000PF 50V NPO 9965 000 36991
C907 067G215Y1007KT KY50VB10M-TP5 5*11.5 9965 000 43652
4600 065G080510332 10NF/50V/0805/X7R 9965 000 39768
093G6433 DIO SIG SM BAV99 (PHSE)R 9965 000 35994
4610 065G080510432 CHIP 0.1U 50V X7R 9965 000 36041
4620 065G080510432 CHIP 0.1U 50V X7R 9965 000 36041 093G6432V LL4148-GSO8 9965 000 39775
4630 065G080510432 CHIP 0.1U 50V X7R 9965 000 36041 093G6432V LL4148-GSO8 9965 000 39775
4640 065G080510432 CHIP 0.1U 50V X7R 9965 000 36041 093G39S12T RLZ20B LLDS 9965 000 39776
4650 065G080510432 CHIP 0.1U 50V X7R 9965 000 36041 093G39S24T RLZ 5.6B LLDS 9965 000 36079
4660 065G080510432 CHIP 0.1U 50V X7R 9965 000 36041 093G39S24T RLZ 5.6B LLDS 9965 000 36079
4670 065G080510432 CHIP 0.1U 50V X7R 9965 000 36041 093G39S38T PTZ 9.1B 9965 000 36080
4680 065G080510432 CHIP 0.1U 50V X7R 9965 000 36041 093G39S40T RLZ 13B LLDS 9965 000 39777
4690 065G080510432 CHIP 0.1U 50V X7R 9965 000 36041 093G39S44T RLZ18B LLDS 9965 000 39778
4700 065G080510432 CHIP 0.1U 50V X7R 9965 000 36041 093G64S511SEM IN4148W 9965 000 39779
4730 065G080510522 CHIP 1UF 25V X7R 0805 9965 000 36073
093G64S511SEM IN4148W 9965 000 39779
4740 065G080510522 CHIP 1UF 25V X7R 0805 9965 000 36073
093G64S511SEM IN4148W 9965 000 39779
4750 065G080510522 CHIP 1UF 25V X7R 0805 9965 000 36073
4760 065G080522131 220PF 50V NPO 9965 000 39769 061G212Y625KT MGFR 6.2MOHM +-5% 1/2W 9965 000 36083
4770 065G080522332 CHIP 0.022UF 50V X7R 0805 9965 000 39770 061G212Y625KT MGFR 6.2MOHM +-5% 1/2W 9965 000 36083
4780 065G080522422 CHIP CAP 0.22 UF 25V X7R 9965 000 39771 071G5529GP FERRITE BEAD 9965 000 39733
4790 065G080533232 3200PF/25V/X7R 9965 000 39772 093G6026T52T RECTIFIER DIODE FR107 9965 000 36030
093G6038T52T FR103 9965 000 36095

056G15810T IC AZ431AZ-AE1 TO-92 BY AAC 9965 000 36101
056G15812 KIA431A-AT/P TO-92 9965 000 36054
S73G17465VW TRANSFORMATER ASSY 9965 000 39227
S80GL19T8V1 TRANSFORMATER ASSY 9965 000 38142
S80GL19T8V1 TRANSFORMATER ASSY 9965 000 38142
Diversity of 190CW7CS/75(CMO) compared with 190CW7CS/00(CMO)

Item TPV 18NC Description Philips 12NC
Z34G0024WV1B BASE 9965 000 43717
Q44G90288131C craton
089G728SAAA00 D-SUB CABLE 9965 000 44523
Q70G90028131B E-D.F.U
Q45G8860952 EPE COVER
Q44G90341 EPS(L)
Q44G90342 EPS(R)
A33G0067VO1T Key Button 9965 000 39716
705GZ-000036 Main Frame ASSY CMO 9965 000 41537
A15G00322 Main Frame CMO 9965 000 41538
089G412A18NIS1 MAINSCORD AUS/NZ 10A 1M8 BK 9965 000 44230
089G412A18NLS1 MAINSCORD AUS/NZ 7A5 1M8 BK 9965 000 44524
Q45G7628B05 PE BAG
A33G00601C Power Lens 9965 000 39714
Q40G19E81316C RATING LABEL
Z34G0021WV1T Rear Cover
705GZV34004 Rear Cover Assy 9965 000 43716
089G728GAA901 SIGNAL CABLE 9965 000 39711
089G728CAA901 SIGNAL CABLE 1.8M 9965 000 44522
Z34G0023WV1B Stand Bottom 9965 000 43719
Z34G0022WV1B Stand Top 9965 000 43718
CBPC6MNNPHSB5 MPLCONVERSION BOARD 9965 000 43524
705GZ9K056003 CPU ASSY 9965 000 43519
Z40G90008135CS CPU Software
CN902 095G80141265 HARNESS 12P-12P 100mm
84 190CW7 LCD Revision List
Manual 3138 106 10544

-First release
-ALL chapters
TELEVISION/MONITOR SAFFTY GUIDELINES FOR THE PROFESSIONAL SERVICE TECHNICIAN
Safety Checks
After the original service problem has been corrected,a complete safety check
should be made. Be sure to check over the entire set, not just the areas 6. New picture tubes are specifically designed to withstand higher operathng
where you have worked. Some previous servicer may have left an unsafe voltages without creating undesirable X-radiation. It is strongly
condition,which could be unknowingly passed on to your customer. Be sure recommended that any shop test fixture which is to be used with the new
to check all of the following: higher voltage chassis be equipped with one of the new type tubes
designed for this service. Addition of a permanently connected HV meter
Fire and Shock Hazard
to the shop test fixture is advisable. The CRT types used in these new
1. Be sure all components are positioned in such a way as to avoid the
sets should never be replaced with any other types, as this may result in
possibility of adjacent component shorts. This is especially important
excessive X-radiation.
on those chassis which are transported to and from the service shop.
7. It is essential to use the specified picture tube to avoid a possible X-diation
2. Never release a repaired unit unless all protective devices such as
problem.
insulators, barries, covers, strain reliefs, and other hardware have been
8. Most TV receivers contain some type of emergency "Hold Down" circuit to
installed in accordance with the original design.
prevent HV from rising to excessive levels in the presence of a failure
3. Soldering and wiring must be inspected to locate possible cold solder
mode. These various circuits should be understood by all technicians
joints,solder splashes,sharp solder points, frayed leads, pinched leads,
servicing them, especially since many hold down circuits are inoperative
or damaged insulation ( including the ac cord).Be certain to remove
as long as the receiver performs normally.
loose solder balls and all other loose foreign particles.
4. Check across-the-line components and other components for physical
Leakage Current Cold Check
evidence of damage or deterioration and replace if necessary. Follow
1. Unplug the ac line cord and connect a jumper between the two prongs of
original layout,lead length, and dress.
the plug.
5. No lead or component should touch a receiving tube or a resistor rated
2. Turn on the power switch.
at 1 watt or more. Lead tension around protruding metal surfaces or
3. Measure the resistance value between the jumpered ac plug and all
edges must be avoided.
exposed cabinet parts of the receiver, such as screw heads, antennas,
6. Critical components having special safety characteristics are identified
and control shafts. When the exposed metallic part has a return path to
with ans by the Ref. No. in the parts list and enclosed within a broken line
the chassis, the reading should be between 1 megohm and 5.2 megohms.
* (where several critical components are grouped in one area) along with
When the exposed metal does not have a return path to the chassis, the
the safety symbols on the schematic diagrams and/or exploded views.
reading must be infinity. Remove the jumper from the ac line cord.
7. When servicing any unit, always use a separate isolation transformer
for the chassis Failure to use a separate isolation transformer may
expose you to possible shock hazard, and may cause damage to
servicing instruments.
8. Many electronic products use a polarized ac line cord (one wide pin on
the plug.) Defeating this safety feature may create a potential hazard to
the service and the user. Extension cords which do not incorporate the
polarizing feature should never be used. TO 0.15 uF WATER
9. After reassembly of the unit, always perform an leakage test or resistance INSTRUMENTS PIPE
test from the line cord to all exposed metal parts of the cabinet. Also check EXPOSED EARTH
all metal control shafts(with knobs removed), antenna terminals, handles, METAL PARTS 1500 ohm, 10W GROUND
screws, etc. to be sure the unit may be safety operated without danger of
electrical shock.
Leakage Current Hot Check
* Broken line
1. Do not use an isolation transformer for this test. Plug the completely
reassembled receiver directly into the ac outlet.
Implosion
2. Connect a 1.5k, 10w resistor paralleled by a 0.15uf. capacitor between
1. All picture tubes used in current model receivers are equipped with an
each exposed metallic cabinet part and a good earth ground such as a
integral implosion system. Care should always be used, and safety
water pipe, as shown above.
glasses worn,whenever handling any picture tube. Avoid scratching or
3. Use an ac voltmeter with at least 5000 ohms volt sensitivity to measure
otherwise damaging the picture tube during installation.
the potential across the resistor.
2. Use only replacement tubes specified by the manufacturer.
4. The potential at any point should not exceed 0.75 volts. A leakage current
tester may be used to make this test; leakage current must not exceed
X-radiation
0.5 milliamps. If a measurement is outside of the specified limits, there is
1. Be sure procedures and instructions to all your service personnel cover
a possibility of shock hazard. The receiver should be repaired and
the subject of X-radiation. Potential sources of X-rays in TV receivers are
rechecked before returning it to the customer.
the picture tube and the high voltage circuits. The basic precaution which
5. Repeat the above procedure with the ac plug reversed.( Note: An ac
must be exercised is to keep the high voltage at the factory recommended
adapter is necessary when a polarized plug is used. Do not defeat the
level.
polarizing feature of the plug.)
2. To avoid possible exposure to X-radiation and electrical shock, only the
manufacturer's specified anode connectors must be used.
Picture Tube Replacement
3. It is essential that the service technician has an accurate HV meter
The primary source of X-radiation in this television receiver is the picture
available at all times. The calibration of this meter should be checked
tube. The picture tube utilized in this chassis is specially constructed to limit
periodically against a reference standard.
X-radiation emissions. For continued X-radiation protection, the replacement
4. When the HV circuitry is operating properly there is no possibility of an x-
tube must be the same type as the original, including suffix letter, or a Philips
radiation problem. High voltage should always be kept at the
approved type.
manufacturer's
rated value-no higher - for optimum performance. Every time a color set is
Parts Replacement
serviced, the brightness should be run up and down while monitoring the
Many electrical and mechanical parts in Philips television sets have special
HV with a meter to be certain that the HV is regulated correctly and does
safety related characteristics. These characteristics are often not evident from
not exceed the specified value. We suggest that you and your technicians
visual inspection nor can the protection afforded by them necessarily be
review test procedures so that HV and HV regulation are always checked as
obtained by using replacement components rated for higher voltage, wattage,
a standard servicing procedure, and the reason for this prudent routine is
etc. The use of a substitute part which does not have the same safety
clearly understood by everyone. It is important to use an accurate and
characteristics as the Philips recommended replacement part shown in this
reliable HV meter. It is recommended that the HV recorded on each
service manual may create shock, fire, or other hazards
customer's invoice, which will demonstrate a proper concern for the
customer's safety.
5. When troubleshooting and making test measurements in a receiver with
a problem of excessive high voltage, reduce the line voltage by means of
a Variac to bring the HV into acceptable limits while troubleshooting. Do
WARNING : Before removing the CRT anode cap, turn the unit OFF and short the HIGH VOLTAGE to the CRT DAG ground.
SERVICE NOTE : The CRT DAG is not at chassis ground.

190CW7

Uploaded by

Copyright:

Available Formats

190CW7

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

190CW7

Uploaded by

Copyright:

Available Formats

19 inch TFT WXGA LCD Colour Monitor Chassis: HUDSON7

REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES

Proper service and repair isimportant to the safe, reliable

recommended. hazardous radiation exposure.

order to minimize the risk of personal injury to service

LCD panel Input DVI-D connector pin

Type NR. : M190A1

Pin No. Assignment Pin No. Assignment

Front View Accessory Pack

VGA signal cable

1 To switch monitor's power On and Off

Notes:If you use an Apple Macintosh , you need to connect the

6 AUTO Automatically adjust the horizontal position,

1 Kensington anti-thief lock

Display position is incorrect 1.Press the Auto button.

Vertical flicker appears 1. Press the Auto button.

Horizontal flicker appears 1. Press the Auto button.

Description of the On Screen Display

Basic and simple instruction on the control keys.

The OSD Tree

Front Control After 15 seconds,

Access Factory Mode

1). Turn off monitor.

OSD MAIN CONTROLS

Unlock OSD function

OSD MAIN CONTROLS

Access Aging Mode Factory Menu

Pixel Defect Tolerances

In order to qualify for repair or replacement due to pixel defects

BRIGHT DOT DEFECTS ACCEPTABLE LEVEL

Pixels and Sub pixels 1 lit subpixel 3 or fewer

Types of Pixel Defects BLACK DOT DEFECTS ACCEPTABLE LEVEL

3 adjacent dark subpixels(one white pixel) 0

Distance between two black dot defects* 15 mm or more

Total black dot defects of all types 5 or fewer

TOTAL DOT DEFECTS ACCEPTABLE LEVEL

Front view 2: Remove the Back Cover Assy

a: Place the monitor face down on a smooth surface as Fig.3.

3. Remove the Key board and bezel.

4. Remove the SHIELDING ASSY , Scaler , Power board.

Alignment procedure Clear image

5.1 White color adjustment

6500K/ sRGB CIE coordinates X = 0.313 ± 0.005

sRGB CIE coordinates X = 0.313 ± 0.005

9300K CIE coordinates X = 0.283 ± 0.015

6500K/ sRGB CIE coordinates X = 0.313 ± 0.015

Factory Mode indicator sRGB CIE coordinates X = 0.313 ± 0.015

Q: What does 'refresh rate' mean in connection with an LCD monitor?

Q: How do I adjust the resolution?

Q: What if I get lost when I am making monitor adjustments?

Q: What is the Auto function?

Q: Will the LCD monitor accept an interlaced signal under PC models?

Q: What does the Refresh Rate mean for LCD?

Q: Will the LCD screen be resistant to scratches?

Q: How should I clean the LCD surface?

Q:Can I change the color setting of my monitor?

Q: Can the Philips LCD Monitor be mounted on the wall?

Q: What is the FPadjust program on the CD-ROM?

Q: How do LCDs compare to CRTs in terms of radiation?

Compatibility with other Peripherals