Manual No.

139
61-00-39
Revision 13
June 2015

Propeller Owner's Manual

and Logbook
Series: HC-B3( )( )-2( )
HC-B3( )( )-3( )
HC-B3( )( )-5( )
HC-B3TF-7( )
HC-B4( )( )-3( )
HC-B4( )( )-5( )
HC-B5M( )-2( )
HC-B5M( )-3( )
HC-B5M( )-5( )
HC-A3(V,MV)F-7( )
Steel Hub Turbine Propellers with Aluminum Blades

Hartzell Propeller Inc.

One Propeller Place
Piqua, OH 45356 - 2634 U.S.A.
Ph: 937 - 778 - 4200 (Hartzell Propeller Inc.)
Ph: 937-778-4379 (Product Support)
Product Support Fax: 937-778-4391
 Propeller Owner's Manual
139

© 1984, 1992, 1994, 1997, 1999, 2001, 2002, 2006, 2009, 2011, 2012, 2013, 2015
Hartzell Propeller Inc. - All rights reserved

Page 2
COVER 61-00-39 Rev. 13 Jun/15
 Propeller Owner's Manual
139

As a fellow pilot, I urge you to read this Manual thoroughly. It

contains a wealth of information about your new propeller.

The propeller is among the most reliable components of your

airplane. It is also among the most critical to flight safety. It
therefore deserves the care and maintenance called for in this
Manual. Please give it your attention, especially the section
dealing with Inspections and Checks.

Thank you for choosing a Hartzell propeller. Properly maintained

it will give you many years of reliable service.

Jim Brown
Chairman, Hartzell Propeller Inc.

Page 1
MESSAGE 61-00-39 Rev. 6 Mar/01
 Propeller Owner's Manual
139

WARNING
People who fly should recognize that various types of
risks are involved; and they should take all precautions to
minimize them, since they cannot be eliminated entirely.
The propeller is a vital component of the aircraft. A
mechanical failure of the propeller could cause a forced
landing or create vibrations sufficiently severe to damage
the aircraft, possibly causing it to become uncontrollable.

Propellers are subject to constant vibration stresses

from the engine and airstream, which are added to high
bending and centrifugal stresses.

Before a propeller is certified as being safe to operate

on an airplane, an adequate margin of safety must be
demonstrated. Even though every precaution is taken in
the design and manufacture of a propeller, history has
revealed rare instances of failures, particularly of the
fatigue type.

It is essential that the propeller is properly maintained

according to the recommended service procedures and
a close watch is exercised to detect impending problems
before they become serious. Any grease or oil leakage,
unusual vibration, or unusual operation should be
investigated and repaired, as it could be a warning that
something serious is wrong.

Page 2
MESSAGE 61-00-39 Rev. 6 Mar/01
 Propeller Owner's Manual
139

For operators of uncertified or experimental aircraft an

even greater level of vigilance is required in the
maintenance and inspection of the propeller. Experimental
installations often use propeller-engine combinations that
have not been tested and approved. In these cases, the
stress on the propeller and, therefore, its safety margin is
unknown. Failure could be as severe as loss of a propeller
or propeller blades and cause loss of propeller control
and/or loss of aircraft control.

Hartzell Propeller Inc. follows FAA regulations for propeller

certification on certificated aircraft. Experimental aircraft
may operate with unapproved engines or propellers or
engine modifications to increase horsepower, such as
unapproved crankshaft damper configurations or high
compression pistons. These issues affect the vibration
output of the engine and the stress levels on the propeller.
Significant propeller life reduction and failure are real
possibilities.

Frequent inspections are strongly recommended if

operating with a non-certificated installation; however,
these inspections may not guarantee propeller reliability,
as a failing device may be hidden from the view of the
inspector. Propeller overhaul is strongly recommended to
accomplish periodic internal inspection.

Visually inspect metal blades for cracks. Inspect hubs,

with particular emphasis on each blade arm for cracks.
Eddy current equipment is recommended for hub
inspection, since cracks are usually not apparent.

Page 3
MESSAGE 61-00-39 Rev. 6 Mar/01
 Propeller Owner's Manual
139

(This page is intentionally blank.)

Page 4
MESSAGE 61-00-39 Rev. 6 Mar/01
 Propeller Owner's Manual
139

REVISION 13 HIGHLIGHTS

Revision 13, dated June 2015, incorporates the following:

• COVER
• Revised to match the manual revision
• REVISION HIGHLIGHTS
• Revised to match the manual revision
• LIST OF EFFECTIVE PAGES
• Revised to match the manual revision
• TABLE OF CONTENTS
• Revised to match the manual revision
• INTRODUCTION
• Revised to add the use of safety cable
• Revised the section, "Reference Publications"
• Made other language/format changes
• INSTALLATION AND REMOVAL
• Revised to add the use of safety cable, where applicable
• Revised the section, "Installing HC-B(3, 4)( )W-3( ) Propeller
on the Aircraft Engine" to include compliance with GE
Aviation Service Bulletin H80-100-72-00019 on Thrush
aircraft models S2R-H80 or S2RHG-H80
• Made other language/format changes
• INSPECTION AND CHECK
• Revised the illustration, "Turbine Engine Overtorque Limits"
• MAINTENANCE PRACTICES
• Revised the section, "Carbon Block Assemblies"

Page 5
61-00-39
REVISION HIGHLIGHTS Rev. 13 Jun/15
 Propeller Owner's Manual
139

(This page is intentionally blank.)

Page 6
61-00-39
REVISION HIGHLIGHTS Rev. 13 Jun/15
 Propeller Owner's Manual
139

REVISION HIGHLIGHTS
1. Introduction
A. General
(1) This is a list of current revisions that have been issued
against this manual. Please compare it to the RECORD
OF REVISIONS page to make sure that all revisions have
been added to the manual.
B. Components
(1) Revision No. indicates the revisions incorporated in this
manual.
(2) Issue Date is the date of the revision.
(3) Comments indicates the level of the revision.
(a) New Issue is a new manual distribution. The manual
is distributed in its entirety. All the page revision
dates are the same and no change bars are used.
(b) Reissue is a revision to an existing manual that
includes major content and/or major format changes.
The manual is distributed in its entirety. All the page
revision dates are the same and no change bars are
used.
(c) Major Revision is a revision to an existing manual
that includes major content or minor content
changes over a large portion of the manual. The
manual is distributed in its entirety. All the page
revision dates are the same, but change bars are
used to indicate the changes incorporated in the
latest revision of the manual.
(d)  Minor Revision is a revision to an existing manual that
includes minor content changes to the manual. Only
the revised pages of the manual are distributed. Each
page retains the date and the change bars associated
with the last revision to that page.

Page 7
61-00-39
REVISION HIGHLIGHTS Rev. 13 Jun/15
 Propeller Owner's Manual
139

Revision No. Issue Date Comments

Revision 5 Oct/99 Reissue
Revision 6 Mar/01 Minor Revision
Revision 7 Oct/02 Minor Revision
Revision 8 Dec/06 Minor Revision
Revision 9 Aug/09 Minor Revision
Revision 10 Jun/11 Minor Revision
Revision 11 Jul/12 Minor Revision
Revision 12 Mar/13 Minor Revision
Revision 13 Jun/15 Minor Revision

Page 8
61-00-39
REVISION HIGHLIGHTS Rev. 13 Jun/15
 Propeller Owner's Manual
139

RECORD OF REVISIONS

Rev. No. Issue Date Date Inserted Inserted By

5 Oct/99 Oct/99 HPI

6 Mar/01 Mar/01 HPI
7 Oct/02 Oct/02 HPI
8 Dec/06 Dec/06 HPI
9 Aug/09 Aug/09 HPI
10 Jun/11 Jun/11 HPI
11 Jul/12 Jul/12 HPI
12 Mar/13 Mar/13 HPI
13 Jun/15 Jun/15 HPI

Page 9
RECORD OF REVISIONS 61-00-39 Rev. 6 Mar/01
 Propeller Owner's Manual
139

RECORD OF REVISIONS

Rev. No. Issue Date Date Inserted Inserted By

Page 10
RECORD OF REVISIONS 61-00-39 Rev. 6 Mar/01
 Propeller Owner's Manual
139

RECORD OF TEMPORARY REVISIONS

TR Issue Date Inserted Date Removed
No. Date Inserted By Removed By
TR-001 Nov/03 Nov/03 HPI 12/06 HPI
TR-002 Nov/03 Nov/03 HPI 4/04 HPI
TR-003 Dec/03 Dec/03 HPI 12/06 HPI
TR-004 Apr/04 Apr/04 HPI 12/06 HPI
TR-005 Oct/04 Oct/04 HPI 12/06 HPI
TR-006 Mar/06 Mar/06 HPI 12/06 HPI

Page 11

RECORD OF TEMPORARY REVISIONS 61-00-39 Rev. 6 Mar/01
 Propeller Owner's Manual
139

RECORD OF TEMPORARY REVISIONS

TR Issue Date Inserted Date Removed
No. Date Inserted By Removed By

Page 12

RECORD OF TEMPORARY REVISIONS 61-00-39 Rev. 6 Mar/01
 Propeller Owner's Manual
139

SERVICE DOCUMENTS LIST

CAUTION 1: DO NOT USE OBSOLETE OR OUTDATED
INFORMATION. PERFORM ALL INSPECTIONS
OR WORK IN ACCORDANCE WITH THE MOST
RECENT REVISION OF A SERVICE DOCUMENT.
INFORMATION CONTAINED IN A SERVICE
DOCUMENT MAY BE SIGNIFICANTLY CHANGED
FROM EARLIER REVISIONS. FAILURE TO
COMPLY WITH INFORMATION CONTAINED
IN A SERVICE DOCUMENT OR THE USE OF
OBSOLETE INFORMATION MAY CREATE AN
UNSAFE CONDITION THAT MAY RESULT IN
DEATH, SERIOUS BODILY INJURY, AND/OR
SUBSTANTIAL PROPERTY DAMAGE.

CAUTION 2: THE INFORMATION FOR THE DOCUMENTS

LISTED INDICATES THE REVISION LEVEL AND
DATE AT THE TIME THAT THE DOCUMENT WAS
INITIALLY INCORPORATED INTO THIS MANUAL.
INFORMATION CONTAINED IN A SERVICE
DOCUMENT MAY BE SIGNIFICANTLY CHANGED
FROM EARLIER REVISIONS. REFER TO THE
APPLICABLE SERVICE DOCUMENT INDEX FOR
THE MOST RECENT REVISION LEVEL OF THE
SERVICE DOCUMENT.
Service Document Number Incorporation Rev/Date
Service Alerts:
SA 57 Oct/02

Service Bulletins:
HC-SB-61-143B Oct/02
HC-SB-61-181A, Rev. 4 Rev. 11 Jul/12
HC-SB-61-275 Aug/09

Page 13

SERVICE DOCUMENTS LIST 61-00-39 Rev. 11 Jul/12
 Propeller Owner's Manual
139

SERVICE DOCUMENTS LIST

Service Document Number Incorporation Rev/Date
Service Letters:
HC-SL-61-217 Oct/99
HC-SL-61-248 Rev. 11, Jul/12
HC-SL-61-254 Aug/09
HC-SL-61-324 Rev. 11, Jul/12

Page 14

SERVICE DOCUMENTS LIST 61-00-39 Rev. 11 Jul/12
 Propeller Owner's Manual
139

AIRWORTHINESS LIMITATIONS

The Airworthiness Limitations section is FAA approved and specifies

maintenance required under 14 CFR §§ 43.16 and 91.403 of the
Federal Aviation Regulations unless an alternative program has
been FAA approved.

FAA APPROVED

by: ______________________________ date: ____________

Manager, Chicago Aircraft Certification

Office,
ACE-115C
Federal Aviation Administration

Rev.
Description of Revision
No.
Adds airworthiness limitation information from Hartzell
9
Overhaul Manuals 118F (61-10-18) and 132A (61-10-32)
For blade life limit, revised the blade model designation
10 to include (N) version for HC-B3TN-3(B,H) and
HC-B4TN-5 (C,F) propellers

Page 15

AIRWORTHINESS LIMITATIONS 61-00-39 Rev. 10 Jun/11
 Propeller Owner's Manual
139

AIRWORTHINESS LIMITATIONS

1. The Airworthiness Limitations in this chapter have been

relocated from Hartzell Overhaul Manuals 118F (61-10-18) and
132A (61-10-32) to this manual.
2. Replacement Time (Life Limits)
A. The FAA establishes specific life limits for certain component
parts, as well as the entire propeller. Such limits require
replacement of the identified parts after a specified number of
hours of use.
B. The following data summarize all current information about
Hartzell life limited parts as related to propeller models
affected by this manual. These parts are not life limited on
other installations; however, time accumulated toward life
limit accrues when first operated on aircraft/engine/propeller
combinations listed and continues regardless of subsequent
installations (which may or may not be life limited).
(1) Blade models that incorporate ice protection components
do not affect the blade life limit. Example: The (B,K) letter
designation in blade model T10178(B,K) indicates
that ice protection components may be installed. If ice
protection components are installed, the blade life limit
still applies.
C. The following list specifies life limits for blades only that are on
FAA Type Certified Aircraft. Blades listed are life limited only on
the specified applications.

FAA APPROVED

by: ______________________________ date: ____________

Manager, Chicago Aircraft Certification Office,

ACE-115C
Federal Aviation Administration

Page 16

AIRWORTHINESS LIMITATIONS 61-00-39 Rev. 10 Jun/11
 Propeller Owner's Manual
139

(1) FAA Type Certified Aircraft - Blade Life Limits

Aircraft/Engine/Propeller Blade Life Limit
Aircraft: Beech T34C,T34C-1 9,634 hours
Engine: Pratt & Whitney - PT6A-25, -25A
Propeller: HC-B3TN-3(B,H)/T10173(N)-11R
Aircraft: CASA 212 31,000 hours
Engine: Allied Signal - TPE331-5-251C
Propeller: HC-B4TN-5(C,F)L/LT10282(N)+4
Aircraft: Fairchild Swearingen SA226TC Metro IIA 9,000 hours*
Engine: Allied Signal - TPE331-10UA, -501G or 511G
Propeller: HC-B3TN-5(C,E,M)/T10282(H)(N)

Aircraft: Mitsubishi MU-2’s 10, 000 hours

Engine: Allied Signal - TPE-331-(5,10)-( )
Propeller: HC-B4TN-5( )L/LT10282N(S)-5.3R
Aircraft: Pilatus PC-7 4,240 hours**
Engine: Pratt and Whitney - PT6A-25,-25A to 9,795 hours
Propeller: HC-B3TN-2( )/T10173C(N)-8
Aircraft: Pilatus PC-7 modified by Sierra Industries 3,000 hours
Engine: Pratt and Whitney - PT6A-25C
Propeller: HC-B3TN-2/T10178(N)-8R

FAA APPROVED

by: ______________________________ date: ____________

Manager, Chicago Aircraft Certification Office,

ACE-115C
Federal Aviation Administration

Page 17

AIRWORTHINESS LIMITATIONS 61-00-39 Rev. 10 Jun/11
 Propeller Owner's Manual
139

* Fairchild Swearingen Metro IIA, Serial Numbers TC398

and subsequent, model T10282()() propeller blades
are life limited when operated above 12,500 pounds
gross weight and must be retired after 9,000 hours
of operation. The life limit begins once the blades
are operated above 12,500 pounds gross weight and
continues regardless of subsequent operating weight.
For those blades on which the total accumulated time in
operation on an aircraft with a gross weight exceeding
12,500 pounds cannot be confirmed, the following
formula will be used to establish an assumed time:
Months from date of STC incorporation X 180 = total
assumed time on subject blades.
** Pilatus PC-7 propeller blades must be retired from
service in accordance with the following schedule:
(a) Aircraft on which Power-On-Spin, Inertia Coupled
Entry, and Snap Roll flight maneuvers are prohibited
must be retired from service when 9795 flight hours
have been acquired.
(b) Aircraft on which Power-On-Spin and Inertia
Coupled Entry flight maneuvers are prohibited must
be retired from service when 4240 flight hours have
been acquired.
(c) Any aircraft, once operated with Snap Roll
maneuvers permitted, must be retired from service
upon acquiring 4240 flight hours.

FAA APPROVED

by: ______________________________ date: ____________

Manager, Chicago Aircraft Certification Office,

ACE-115C
Federal Aviation Administration

Page 18

AIRWORTHINESS LIMITATIONS 61-00-39 Rev. 10 Jun/11
 Propeller Owner's Manual
139

D. The following list specifies life limits for blades only that are
on an aircraft without FAA Type Certificate. Blades listed are
life limited only on the specified applications.
(1) Aircraft Without FAA Type Certificate - Blade Life Limits

Aircraft/Engine/Propeller Blade Life Limit

Aircraft: Embraer EMB-312 12,000 hours
Engine: Pratt & Whitney - PT6A-25C
Propeller: HC-B3TN-3(C,D)/T10178(B,K)-8R
Aircraft: NDN-1T Firecracker 45,000 hours
Engine: Pratt & Whitney - PT6A-25A
Propeller: HC-B3TN-3(B,C)/T10173(B,K)-17
Aircraft: North American Rockwell OV-10A 20,900 hours
Engine: Garrett T76-G-418M, -419M
Propeller: HC-B4MN-5B(L)/(L)M9990N
Aircraft: North American Rockwell OV-10D 20,900 hours
Engine: Garrett T76-G-420, -421
Propeller: HC-B4MN-5B(L)/(L)M9990N
Aircraft: Antonov AN-38-100 (MTOW 9500 kg) 22,000 hours
Engine: Garrett - TPE-331-14GR
Propeller: HC-B5MA-5A/M11276NK-3
Aircraft: Antonov AN-38-100 (MTOW 9900 kg) 11,300 hours
Engine: Garrett TPE-331-14GR
Propeller: HC-B5MA-5A/M11276NCK-3
Aircraft: Embraer EMB-314 PT6A-68C 9,960 hours
Engine: Pratt & Whitney
Propeller: HC-B5MA-2/M9128NS(K)

FAA APPROVED

by: ______________________________ date: ____________

Manager, Chicago Aircraft Certification Office,

ACE-115C
Federal Aviation Administration

Page 19

AIRWORTHINESS LIMITATIONS 61-00-39 Rev. 10 Jun/11
 Propeller Owner's Manual
139

E. The following list specifies life limits for hubs only. Hub units
listed are life limited only on the specified applications.
(1) FAA Type Certified Aircraft - Hub Life Limits
NONE
(2) Aircraft Without FAA Type Certificate - Hub Life Limits

Aircraft/Engine/Propeller Hub Life Limit

Aircraft: Embraer EMB-314 19,589 hours
Engine: Pratt & Whitney - PT6A-68C
Propeller: HC-B5MA-2/M9128NS(K)

F. The following list specifies life limits for clamps only. Clamp
assemblies listed are life limited only on the specified
applications.
(1) Propeller Models on FAA Type Certified Aircraft
NONE
(2) Propeller Models on Aircraft without FAA Type Certificate

Aircraft/Engine/Propeller Clamp Life Limit

Aircraft: Embraer EMB-314 19,589 hours
Engine: Pratt & Whitney - PT6A-68C
Propeller: HC-B5MA-2/M9128NS(K)

FAA APPROVED

by: ______________________________ date: ____________

Manager, Chicago Aircraft Certification Office,

ACE-115C
Federal Aviation Administration

Page 20

AIRWORTHINESS LIMITATIONS 61-00-39 Rev. 10 Jun/11
 Propeller Owner's Manual
139

G. The following list specifies life limits for pitch change rod
part number C-1169-1 only. Pitch change rods listed are life
limited only on the specified applications.
(1) Propeller Models on FAA Type Certified Aircraft

Aircraft/Engine/Propeller Pitch Change

Rod Life Limit
Aircraft: Air Tractor AT-802(A) 6,026 hours
Engine: Honeywell - TPE331-14GR( )
Propeller: HC-B5MA-5H/M11693NS

(2) Propeller Models on Aircraft without FAA Type Certificate

Aircraft/Engine/Propeller Pitch Change

Rod Life Limit
Aircraft: Marsh/Grumman S2 6,026 hours
Engine: Honeywell - TPE331-14( )
Propeller: HC-B5MP-5/M11276(N)S(K)
Aircraft: Marsh/Grumman S2F3 6,026 hours
Engine: Honeywell - TPE331-14( )
Propeller: HC-B5MA-5H/M11692NS(K)

FAA APPROVED

by: ______________________________ date: ____________

Manager, Chicago Aircraft Certification Office,

ACE-115C
Federal Aviation Administration

Page 21

AIRWORTHINESS LIMITATIONS 61-00-39 Rev. 10 Jun/11
 Propeller Owner's Manual
139

H. The following list specifies life limits for pitch change rod
part number C-1169-2 only. Pitch change rods listed are life
limited only on the specified applications.
(1) Propeller Models on FAA Type Certified Aircraft
NONE
(2) Propeller Models on Aircraft without FAA Type Certificate

Aircraft/Engine/Propeller Pitch Change

Rod Life Limit
Aircraft: Antonov AN-38-100 12,053 hours
Engine: Honeywell - TPE331-14( )
Propeller: HC-B5MA-5A/M11276N(C)K-3

2. Periodic Inspections
A. The HC-B3TN-3UL/LT10173N-21R propeller installed on
Advanced Aerodynamics & Structures model 450 “Jetcruzer”
is required to have repetitive blade inspection for erosion
and/or corrosion at intervals not to exceed 24 months or
600 hours of operation, whichever occurs first. Inspection
methods and procedures are described in Hartzell Service
Bulletin HC-SB-61-181A.

FAA APPROVED

by: ______________________________ date: ____________

Manager, Chicago Aircraft Certification Office,

ACE-115C
Federal Aviation Administration

Page 22

AIRWORTHINESS LIMITATIONS 61-00-39 Rev. 10 Jun/11
 Propeller Owner's Manual
139

LIST OF EFFECTIVE PAGES

Chapter Page Revision Date
Cover Cover and Inside Cover Rev. 13 Jun/15
Message 1 thru 4 Rev. 6 Mar/01
Revision Highlights 5 thru 8 Rev. 13 Jun/15
Record of Revisions 9 and 10 Rev. 6 Mar/01
Record of Temporary Revisions 11 and 12 Rev. 6 Mar/01
Service Documents List 13 and 14 Rev. 11 Jul/12
Airworthiness Limitations 15 thru 22 Rev. 10 Jun/11
List of Effective Pages 23 and 24 Rev. 13 Jun/15
Table of Contents 25 and 26 Rev. 12 Mar/13
Table of Contents 27 Rev. 13 Jun/15
Table of Contents 28 thru 31 Rev. 12 Mar/13
Table of Contents 32 Rev. 13 Jun/15
Table of Contents 33 and 34 Rev. 12 Mar/13
Introduction 1-1 thru 1-5 Rev. 12 Mar/13
Introduction 1-6 thru 1-13 Rev. 13 Jun/15
Introduction 1-14 thru 1-16 Rev. 11 Jul/12
Description and Operation 2-1 Rev. 12 Mar/13
Description and Operation 2-2 Rev. 11 Jul/12
Description and Operation 2-3 Rev. 10 Jun/11
Description and Operation 2-4 Rev. 7 Oct/02
Description and Operation 2-5 Rev. 11 Jul/12
Description and Operation 2-6 thru 2-19 Rev. 7 Oct/02
Description and Operation 2-20 Rev. 11 Jul/12
Description and Operation 2-21 thru 2-27 Rev. 7 Oct/02
Description and Operation 2-28 and 2-29 Rev. 11 Jul/12
Description and Operation 2-30 and 2-31 Rev. 10 Jun/11
Description and Operation 2-32 thru 2-35 Rev. 7 Oct/02
Description and Operation 2-36 thru 2-38 Rev. 12 Mar/13
Installation and Removal 3-1 thru 3-4 Rev. 13 Jun/15
Installation and Removal 3-5 Rev. 7 Oct/02
Installation and Removal 3-6 thru 3-10 Rev. 11 Jul/12
Installation and Removal 3-11 Rev. 8 Dec/06
Installation and Removal 3-12 Rev. 13 Jun/15

Page 23
LIST OF EFFECTIVE PAGES 61-00-39 Rev. 13 Jun/15
 Propeller Owner's Manual
139

LIST OF EFFECTIVE PAGES

Chapter Page Revision Date

Installation and Removal 3-13 thru 3-16 Rev. 11 Jul/12

Installation and Removal 3-17 and 3-18 Rev. 13 Jun/15
Installation and Removal 3-19 Rev. 11 Jul/12
Installation and Removal 3-20 thru 3-23 Rev. 13 Jun/15
Installation and Removal 3-24 and 3-25 Rev. 11 Jul/12
Installation and Removal 3-26 thru 3-29 Rev. 13 Jun/15
Installation and Removal 3-30 Rev. 11 Jul/12
Installation and Removal 3-31 thru 3-70 Rev. 13 Jun/15
Testing and Troubleshooting 4-1 and 4-2 Rev. 12 Mar/13
Testing and Troubleshooting 4-3 Rev. 7 Oct/02
Testing and Troubleshooting 4-4 Rev. 12 Mar/13
Testing and Troubleshooting 4-5 thru 4-10 Rev. 7 Oct/02
Testing and Troubleshooting 4-11 and 4-12 Rev. 10 Jun/11
Inspection and Check 5-1 Rev. 12 Mar/13
Inspection and Check 5-2 thru 5-19 Rev. 11 Jul/12
Inspection and Check 5-20 and 5-21 Rev. 12 Mar/13
Inspection and Check 5-22 Rev. 11 Jul/12
Inspection and Check 5-23 Rev. 13 Jun/15
Inspection and Check 5-24 thru 5-34 Rev. 11 Jul/12
Maintenance Practices 6-1 and 6-2 Rev. 12 Mar/13
Maintenance Practices 6-3 Rev. 11 Jul/12
Maintenance Practices 6-4 Rev. 6 Mar/01
Maintenance Practices 6-5 thru 6-8 Rev. 11 Jul/12
Maintenance Practices 6-9 Rev. 13 Jun/15
Maintenance Practices 6-10 Rev. 11 Jul/12
Maintenance Practices 6-11 Rev. 12 Mar/13
Maintenance Practices 6-12 thru 6-22 Rev. 11 Jul/12
Maintenance Practices 6-23 and 6-24 Rev. 12 Mar/13
Anti-ice and De-ice Systems 7-1 thru 7-8 Rev. 12 Mar/13
Records 8-1 thru 8-4 Rev. 5 Oct/99

Page 24
LIST OF EFFECTIVE PAGES 61-00-39 Rev. 13 Jun/15
 Propeller Owner's Manual
139

CONTENTS Page

MESSAGE.......................................................................................... 1
REVISION HIGHLIGHTS................................................................... 5
RECORD OF REVISIONS................................................................. 9
RECORD OF TEMPORARY REVISIONS........................................ 11
SERVICE DOCUMENT LIST........................................................... 13
AIRWORTHINESS LIMITATIONS.................................................... 15
LIST OF EFFECTIVE PAGES.......................................................... 23
TABLE OF CONTENTS.................................................................... 25
INTRODUCTION.............................................................................1-1
1. Purpose.......................................................................................1-3
2. Airworthiness Limitations............................................................1-3
3. Airframe or Engine Modifications................................................1-4
4. Restrictions and Placards...........................................................1-4
5. General.......................................................................................1-5
A. Personnel Requirements........................................................1-5
B. Maintenance Practices...........................................................1-5
C. Continued Airworthiness.........................................................1-8
D. Propeller Critical Parts............................................................1-8
6. Reference Publications...............................................................1-9
7. Definitions.................................................................................1-10
8. Abbreviations............................................................................1-14
9. Hartzell Propeller Inc. Product Support.....................................1-15
10. Warranty Service.....................................................................1-15
11. Hartzell Propeller Inc. Recommended Facilities.....................1-16

Page 25
TABLE OF CONTENTS 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

CONTENTS Page

DESCRIPTION AND OPERATION..................................................2-1

1. Functional Description of Constant Speed Propeller Types........2-5
A. Feathering Propellers HC-B(3,5)( )( )-2( )...............................2-5
B. Feathering and Reversing Propellers
HC-B(3,4,5)( )( )-3( ) Series (External Beta System).............2-9
C. Feathering and Reversing Propellers
HC-B(3,4,5)( )( )-5( ) Series (Internal Beta System)............2-17
D. Feathering and Reversing Propellers
HC-( )3( )( )-7( ) Series (Beta Valve System).......................2-24
2. Model Designation....................................................................2-28
A. Steel Hub Propeller Model Identification...............................2-28
B. Aluminum Blade Model Identification....................................2-31
3. Governors.................................................................................2-33
A. Theory of Operation..............................................................2-33
4. Propeller Ice Protection Systems..............................................2-36
A. Propeller Anti-ice System......................................................2-36
B. Propeller De-ice System.......................................................2-37
INSTALLATION AND REMOVAL.....................................................3-1
1. Tools, Consumables, and Expendables......................................3-3
A. Tooling....................................................................................3-3
B. Consumables..........................................................................3-4
C. Expendables...........................................................................3-4
2. Pre-Installation............................................................................3-5
A. Inspection of Shipping Package.............................................3-5
B. Uncrating................................................................................3-5
C. Inspection after Shipment.......................................................3-5
D. Reassembly of a Propeller Disassembled for Shipment.........3-5

Page 26
TABLE OF CONTENTS 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

CONTENTS Page

3. Propeller Assembly Installation...................................................3-6

A. Precautions.............................................................................3-6
B. Installing HC-B(3, 5)( )( )-2( ) Propeller on the
Aircraft Engine.......................................................................3-7
C. Installing HC-B(3,4,5)( )(A,N,P)-3( ) Propeller on the
Aircraft Engine.....................................................................3-14
D. Installing HC-B(3,4)( )W-3( ) Propeller on the
Aircraft Engine.....................................................................3-20
E. Installing HC-B(3,4)( )( )-5( ) Propeller, with a One-piece
Spinner Mounting Plate, on the Aircraft Engine...................3-29
F. Installing HC-B(3,4,5)( )( )-5( ) Propeller, with a Two-piece
Spinner Mounting Plate, on the Aircraft Engine...................3-35
G. Installing HC-( )3( )( )-7( ) Propeller on the
Allison Engine......................................................................3-40
4. Spinner Dome Installation.........................................................3-50
5. Post-Installation Checks............................................................3-50
6. Spinner Dome Removal............................................................3-51
7. Propeller Assembly Removal....................................................3-52
A. Removal of HC-B(3,5)( )( )-2( ) Propellers............................3-52
B. Removal of HC-B(3,4,5)( )(A,N,P)-3( ) Propellers................3-55
C. Removal of HC-B(3,4)( )W-3( ) Propellers............................3-59
D. Removal of HC-B(3,4,5)( )( )-5( ) Propellers.........................3-62
E. Removal of HC-( )3( )( )-7( ) Propellers................................3-65
F. Removal of Beta Valve Assembly for
HC-( )3( )( )-7( ) Propellers .................................................3-68

Page 27
TABLE OF CONTENTS 61-00-39 Rev. 13 Jun/15
 Propeller Owner's Manual
139

CONTENTS Page

TESTING AND TROUBLESHOOTING...........................................4-1

1. Operational Tests........................................................................4-3
A. Initial Run-Up..........................................................................4-3
B. Post-Run Check......................................................................4-3
C. Maximum RPM (Static) Hydraulic Low Pitch Stop Check.......4-3
D. Feathering Pitch Stop Adjustment..........................................4-4
E. Start Lock Unit Adjustment.....................................................4-4
F. Propeller Ice Protection System.............................................4-4
2. Troubleshooting ..........................................................................4-4
A. Hunting and Surging...............................................................4-4
B. Engine Speed Varies with Airspeed........................................4-5
C. Loss of Propeller Control........................................................4-6
D. Failure to Feather (or feathers slowly)....................................4-6
E. Failure to Unfeather................................................................4-7
F. Start Lock Units Fail to Latch on Shutdown
(-2, -5 and some -3 Models)..................................................4-7
G. Vibration..................................................................................4-8
H. Propeller Overspeed...............................................................4-9
I. Propeller Underspeed.............................................................4-9
J. Oil or Grease Leakage..............................................................4-10
INSPECTION AND CHECKS..........................................................5-1
1. Pre-Flight Checks........................................................................5-3
2. Post-Flight Checks......................................................................5-5
3. Operational Checks.....................................................................5-6
4. Required Periodic Inspections and Maintenance........................5-7
A. Periodic Inspections................................................................5-7
B. Periodic Maintenance.............................................................5-8
C. Compliance Inspections..........................................................5-8
D. Airworthiness Limitations...................................................... 5-11
E. Overhaul Periods..................................................................5-12

Page 28
TABLE OF CONTENTS 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

CONTENTS Page
5. Inspection Procedures..............................................................5-13
A. Blade Damage......................................................................5-13
B. Grease or Oil Leakage..........................................................5-13
C. Vibration................................................................................5-15
D. Tachometer Inspection..........................................................5-16
E. Blade Track...........................................................................5-19
F. Loose Blades........................................................................5-20
G. Corrosion..............................................................................5-20
H. Spinner Damage...................................................................5-20
I. Electric De-ice System..........................................................5-20
J. Anti-ice System.....................................................................5-21
6. Special Inspections...................................................................5-21
A. Overspeed/Overtorque.........................................................5-21
B. Propeller Ground Idle Operating Restrictions.......................5-24
C. Lightning Strike.....................................................................5-30
D. Foreign Object Strike............................................................5-31
E. Fire Damage or Heat Damage..............................................5-33
7. Long Term Storage....................................................................5-34
MAINTENANCE PRACTICES.........................................................6-1
1. Cleaning......................................................................................6-3
A. General Cleaning....................................................................6-3
B. Spinner Cleaning and Polishing..............................................6-5
2. Lubrication...................................................................................6-5
A. Lubrication Intervals................................................................6-5
B. Lubrication Procedure.............................................................6-6
C. Approved Lubricants...............................................................6-8
3. Carbon Block Assemblies...........................................................6-9
A. Inspection...............................................................................6-9
B. Replacement of A-3026 Carbon Block Unit
in the A-3044 Carbon Block Assembly...................................6-9
C. Installation of the A-3044 Carbon Block Assembly...............6-10

Page 29
TABLE OF CONTENTS 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

CONTENTS Page

4. Blade Repairs............................................................................ 6-11

A. Repair of Nicks and Gouges.................................................6-13
B. Repair of Bent Blades...........................................................6-15
5. Painting After Repair.................................................................6-16
A. Painting of Aluminum Blades................................................6-18
6. Dynamic Balance......................................................................6-20
A. Overview...............................................................................6-20
B. Inspection Procedures Before Balancing..............................6-21
C. Modifying Spinner Bulkhead to Accommodate Dynamic
Balance Weights..................................................................6-21
D. Placement of Balance Weights for Dynamic Balance...........6-22
7. Propeller Ice Protection Systems..............................................6-23
A. Electric De-ice System..........................................................6-23
B. Anti-ice System.....................................................................6-23
ANTI-ICE AND DE-ICE SYSTEMS.................................................7-1
1. Introduction.................................................................................7-3
A. Propeller De-Ice System.........................................................7-3
B. Propeller Anti-ice System........................................................7-3
2. System Description.....................................................................7-4
A. De-ice System........................................................................7-4
B. Anti-ice System.......................................................................7-5
3. De-ice System Functional Tests..................................................7-5
4. Anti-ice System Functional Tests................................................7-5
5. De-ice and Anti-ice System Inspections......................................7-6
A. De-ice System Inspections.....................................................7-6
B. Anti-ice System Inspections....................................................7-6
6. De-ice and Anti-ice System Troubleshooting..............................7-7
A. De-ice System Troubleshooting..............................................7-7
B. Anti-ice System Troubleshooting............................................7-7

Page 30
TABLE OF CONTENTS 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

RECORDS.......................................................................................8-1
1. Introduction.................................................................................8-3
2. Record Keeping..........................................................................8-3
A. Information to be Recorded....................................................8-3

LIST OF ILLUSTRATIONS Page

HC-B(3,5)( )( )-2( ) Propeller Assembly........... Figure 2-1...............2-4

Steel Hub Unit................................................. Figure 2-2...............2-5
HC-B(3,4,5)( )( )-3( ) Propeller Assembly........ Figure 2-3...............2-8
Start Lock Unit on HC-B(3,4,5)( )( )-3( )
Propeller Assembly................................... Figure 2-4.............2-12
HC-B(3,4)( )( )-5( ) Propeller Assembly with
One-piece Spinner Mounting Plate
(Superseded Configuration)...................... Figure 2-5.............2-14
HC-B3( )( )-5( ) Propeller Assembly with
Two-piece Spinner Mounting Plate
(New Configuration).................................. Figure 2-6.............2-15
HC-B(4,5)( )( )-5( ) Propeller Assembly with
Two-piece Spinner Mounting Plate
(New Configuration).................................. Figure 2-7.............2-16
HC-A3VF-7( ) Propeller Assembly................... Figure 2-8.............2-22
HC-A3MVF-7( ) and HC-B3TF-7( )
Propeller Assembly................................... Figure 2-9.............2-23
Governor in Onspeed Condition..................... Figure 2-10............2-32
Governor in Underspeed Condition................ Figure 2-11............2-32
Governor in Overspeed Condition.................. Figure 2-12............2-32
Feathering Governor...................................... Figure 2-13............2-34
Synchronizer/Synchrophaser Governor......... Figure 2-14............2-34
Mounting Bolt and Washer.............................. Figure 3-1...............3-9

Page 31
TABLE OF CONTENTS 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

LIST OF ILLUSTRATIONS Page

Installing Propeller on Engine Flange.............. Figure 3-2.............3-10

Diagram of Torquing Sequence for
Propeller Mounting Bolts........................... Figure 3-3............. 3-11
Determining Torque Value When Using
Torquing Adaptor....................................... Figure 3-4.............3-13
Beta System Puller for Decompressing
-3 Series External Beta System................ Figure 3-5.............3-16
Carbon Block and Beta Ring Clearance.......... Figure 3-6.............3-18
Carbon Block Assembly.................................. Figure 3-7.............3-18
Hub-to-Spacer O-ring Location
in the Spacer............................................. Figure 3-8.............3-22
Installing the HC-B(3,4)( )W-3( ) Propeller
on the Engine Flange................................ Figure 3-9.............3-24
Installing the Washer on the Mounting Stud... Figure 3-10............3-26
One-piece Spinner Mounting Plate
Installation................................................ Figure 3-11............3-30
Beta Valve System......................................... Figure 3-12............3-38
Cross Section View of the Beta Valve
System..................................................... Figure 3-13............3-39
-7( ) Propeller Assembly................................. Figure 3-14............3-42
Spring Assembly to Cylinder
Attachment Details................................... Figure 3-15............3-43
Piston to Link Arm Attachment Details........... Figure 3-16............3-43
Filed Rod for Set Screw................................. Figure 3-17............3-48
Checking Blade Track..................................... Figure 5-1.............5-18
Blade Play....................................................... Figure 5-2.............5-18
Turbine Engine Overspeed Limits.................. Figure 5-3.............5-22
Turbine Engine Overtorque Limits.................. Figure 5-4.............5-23

Page 32
TABLE OF CONTENTS 61-00-39 Rev. 13 Jun/15
 Propeller Owner's Manual
139

LIST OF ILLUSTRATIONS Page

Example of an Evaluation of Ground

Idle RPM Check........................................ Figure 5-5.............5-25
Corrective Action Required.............................. Figure 5-6.............5-26
Grease Fitting.................................................. Figure 6-1...............6-4
Lubrication Label............................................. Figure 6-2...............6-7
Repair Limitations............................................ Figure 6-3.............6-12

LIST OF TABLES Page

Propeller/Engine Flange O-rings...................... Table 3-1................3-8

Propeller Mounting Hardware........................... Table 3-2................3-8
Torque Table..................................................... Table 3-3..............3-12
Approved Touch-up Paints............................... Table 6-1..............6-17

Page 33
TABLE OF CONTENTS 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

(This page is intentionally blank.)

Page 34
TABLE OF CONTENTS 61-00-39 Rev. 12 Mar/13
 Propeller Owner’s Manual
139

INTRODUCTION - CONTENTS

1. Purpose.......................................................................................1-3
2. Airworthiness Limitations............................................................1-3
3. Airframe or Engine Modifications................................................1-4
4. Restrictions and Placards...........................................................1-4
5. General.......................................................................................1-5
A. Personnel Requirements........................................................1-5
B. Maintenance Practices...........................................................1-5
C. Continued Airworthiness.........................................................1-8
D. Propeller Critical Parts............................................................1-8
6. Reference Publications...............................................................1-9
7. Definitions.................................................................................1-10
8. Abbreviations............................................................................1-14
9. Hartzell Propeller Inc. Product Support.....................................1-15
10. Warranty Service.....................................................................1-15
11. Hartzell Propeller Inc. Recommended Facilities.....................1-16

Page 1-1
INTRODUCTION 61-00-39 Rev. 12 Mar/13
 Propeller Owner’s Manual
139

(This page is intentionally blank.)

Page 1-2
INTRODUCTION 61-00-39 Rev. 12 Mar/13
 Propeller Owner’s Manual
139

1. Purpose
A. This manual has been reviewed and accepted by the FAA.
Additionally, the Airworthiness Limitations Section of this
manual has been approved by the FAA.
CAUTION: KEEP THIS MANUAL WITH THE
PROPELLER OR WITH THE AIRCRAFT
ON WHICH IT IS INSTALLED, AT ALL
TIMES. THE LOGBOOK RECORD WITHIN
THIS MANUAL MUST BE MAINTAINED,
RETAINED CONCURRENTLY,
AND BECOME A PART OF THE AIRCRAFT
AND ENGINE SERVICE RECORDS.
B. This manual supports constant speed feathering and
constant speed feathering and reversing steel hub turbine
propellers with aluminum blades.
(1) The purpose of this manual is to enable qualified
personnel to install, operate, and maintain a Hartzell
Propeller Inc. Constant Speed Feathering or Constant
Speed Feathering and Reversing Steel Hub Propeller.
Separate manuals are available concerning
overhaul procedures and specifications for the propeller.
(2) This manual includes several design types. Sample
hub and blade model numbers within this design are
included in the Description and Operation Chapter of
this manual.
NOTE: All propeller models included in this manual
use aluminum propeller blades. Propellers
that use composite blades are supported by
Hartzell Propeller Inc. Manual 146 (61-00-46).
2. Airworthiness Limitations
A. Refer to the Airworthiness Limitations chapter of this manual
for Airworthiness Limitations information.

Page 1-3
INTRODUCTION 61-00-39 Rev. 12 Mar/13
 Propeller Owner’s Manual
139

3. Airframe or Engine Modifications

A. Propellers are approved vibrationwise on airframe and
engine combinations based on tests or analysis of similar
installations. This data has demonstrated that propeller stress
levels are affected by airframe configuration, airspeed, weight,
power, engine configuration and flight maneuvers. Aircraft
modifications which can effect propeller stress include, but
are not limited to: aerodynamic changes ahead of or behind
the propeller, realignment of the thrust axis, increasing or
decreasing airspeed limits, increasing or decreasing weight
limits (less significant on piston engines), and the addition of
approved flight maneuvers (utility and aerobatic).
B. Engine modifications can also affect the propeller. The two
primary categories of engine modifications are those which
affect structure and those which affect power. An example
of a structural engine modification is the alteration of the
crankshaft or damper of a piston engine. Any change to the
weight, stiffness or tuning of rotating components could result
in a potentially dangerous resonant condition which is not
detectable by the pilot. Most common engine modifications
affect the power during some phase of operation. Some
increase the maximum power output, while others improve
the power available during hot and high operation (flat
rating) or at off-peak conditions. Examples of such engine
modifications include, but are not limited to: changes to the
compressor, power turbine or hot section of a turboprop
engine; and on piston engines, the addition or alteration of a
turbocharger or turbonormalizer, increased compression ratio,
increased RPM, altered ignition timing, electronic ignition,
full authority digital electronic controls (FADEC), or tuned
induction or exhaust.
C. All such modifications must be reviewed and approved by
the propeller manufacturer prior to obtaining approval on the
aircraft.
4. Restrictions and Placards
A. The propellers covered by this manual may have a restricted
operating range that requires a cockpit placard.
(1) The restrictions, if present, will vary depending on the
propeller, blade, engine, and/or aircraft model.

Page 1-4
INTRODUCTION 61-00-39 Rev. 12 Mar/13
 Propeller Owner’s Manual
139

(2) Review the propeller and aircraft type certificate data

sheet (TCDS), Pilot Operating Handbook (POH), and any
applicable Airworthiness Directives for specific information.
5. General
A. Personnel Requirements
(1) Inspection, Repair, and Overhaul
(a) Compliance to the applicable regulatory requirements
established by the Federal Aviation Administration
(FAA) or foreign equivalent is mandatory for anyone
performing or accepting responsibility for any
inspection and/or repair and/or overhaul of any Hartzell
Propeller Inc. product.
(b) Personnel performing maintenance on steel hub
propellers are expected to have sufficient training and
certifications (when required by the applicable Aviation
Authority) to accomplish the work required in a safe and
airworthy manner.
B. Maintenance Practices
(1) The propeller and its components are highly vulnerable to
damage while they are removed from the engine. Properly
protect all components until they are reinstalled on the
engine.
(2) Never attempt to move the aircraft by pulling on the
propeller.
(3) Avoid the use of blade paddles. Do not place the blade
paddle in the area of the de-ice boot when applying
torque to a blade assembly. Place the blade paddle in the
thickest area of the blade, just outside of the de-ice boot.
Use one blade paddle per blade.
(4) Use only the approved consumables, e.g., cleaning agents,
lubricants, etc.
(5) Safe Handling of Paints and Chemicals
(a) Always use caution when handling or being exposed to
paints and/or chemicals during propeller overhaul and
maintenance procedures.
(b) Before using paint or chemicals, always read the
manufacturer’s label on the container and follow
specified instructions and procedures.

Page 1-5
INTRODUCTION 61-00-39 Rev. 12 Mar/13
 Propeller Owner’s Manual
139

(c) Refer to the product’s Material Safety Data Sheet

(MSDS) for detailed information about physical
properties, health, and physical hazards of any
chemical.
(6) Observe applicable torque values during maintenance.
(7) Before installing the propeller on the engine, the
propeller must be statically balanced. New propellers are
statically balanced at Hartzell Propeller Inc. Overhauled
propellers must be statically balanced by a certified
propeller repair station with the appropriate rating before
return to service.
NOTE: Dynamic balance is recommended, but may
be accomplished at the discretion of the
operator, unless specifically required by the
airframe or engine manufacturer. Dynamic
balancing is to be accomplished in accordance
with the procedures and limitations in
Maintenance Practices chapter of this manual.
Additional procedures may be found in the
aircraft maintenance manual.
(8) As necessary, use a soft, non-graphite pencil or crayon
to make identifying marks on components.
(9) As applicable, follow military standard NASMS33540 for
safety wire, safety cable, and cotter pin general
practices. Use 0.032 inch (0.81 mm) diameter stainless
steel safety wire unless otherwise indicated.

Page 1-6
INTRODUCTION 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

WARNING: DO NOT USE OBSOLETE OR

OUTDATED INFORMATION. PERFORM
ALL INSPECTIONS OR WORK IN
ACCORDANCE WITH THE MOST
RECENT REVISION OF THIS MANUAL.
INFORMATION CONTAINED IN THIS
MANUAL MAY BE SIGNIFICANTLY
CHANGED FROM EARLIER REVISIONS.
FAILURE TO COMPLY WITH THIS
MANUAL OR THE USE OF OBSOLETE
INFORMATION MAY CREATE AN UNSAFE
CONDITION THAT MAY RESULT IN
DEATH, SERIOUS BODILY INJURY, AND/
OR SUBSTANTIAL PROPERTY DAMAGE.
FOR THE MOST RECENT REVISION
LEVEL OF THIS MANUAL, REFER TO THE
HARTZELL PROPELLER INC. WEBSITE AT
WWW.HARTZELLPROP.COM.
(10)The information in this manual revision supersedes data
in all previous published revisions of this manual.
(11) The airframe manufacturer’s manuals should be used in
addition to the information in this manual due to possible
special requirements for specific aircraft applications.
(12)If the propeller is equipped with an ice protection system
that uses components supplied by Hartzell Propeller
Inc., applicable instructions and technical information for
the components supplied by Hartzell Propeller Inc. can
be found in the following publications available on the
Hartzell Propeller Inc. website at www.hartzellprop.com:
(a) Manual 180 (30-61-80) - Propeller Ice Protection
System Manual
(b) Manual 181 (30-60-81) - Propeller Ice Protection
System Component Maintenance Manual
(c) Manual 182 (61-12-82) - Propeller Electrical De-ice
Boot Removal and Installation Manual
(d) Manual 183 (61-12-83) - Propeller Anti-icing Boot
Removal and Installation Manual

Page 1-7
INTRODUCTION 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(13)Propeller ice protection system components not

supplied by Hartzell Propeller Inc. are controlled by the
applicable TC or STC holder’s Instructions for Continued
Airworthiness (ICA).
(14)Approved corrosion protection followed by approved
paint must be applied to all aluminum blades. For
information concerning the application of corrosion
protection and paint, refer to the Maintenance Practices
chapter of this manual. Operation of blades without the
specified coatings and finishes, i.e., “polished blades”, is
not permitted.
C. Continued Airworthiness
(1) Operators are urged to stay informed of Airworthiness
information using Hartzell Propeller Inc. Service Bulletins
and Service Letters that are available from Hartzell
Propeller Inc. distributors, or from the Hartzell Propeller
Inc. factory by subscription. Selected information is also
available on the Hartzell Propeller Inc. website at
www.hartzellprop.com.
D. Propeller Critical Parts
(1) The following maintenance procedures may involve
propeller critical parts. These procedures have been
substantiated based on Engineering analysis that
expects this product will be operated and maintained
using the procedures and inspections provided in the
Instructions for Continued Airworthiness (ICA) for this
product. Refer to the Illustrated Parts List chapter of
the applicable maintenance manual for the applicable
propeller model for the identification of specific Critical
Parts.
(2) Numerous propeller system parts can produce a
propeller Major or Hazardous effect, even though those
parts may not be considered as Critical Parts. The
operating and maintenance procedures and inspections
provided in the ICA for this product are, therefore,
expected to be accomplished for all propeller system
parts.

Page 1-8
INTRODUCTION 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

6. Reference Publications
A. Hartzell Propeller Inc. Publications
NOTE: The following publications are referenced within
this manual:
Active Hartzell Propeller Inc. Service Bulletins, Service
Letters, Service Instructions, and Service Advisories.
Hartzell Propeller Inc. Manual No. 118F (61-10-18) - Three
and Four-Blade Steel Hub Turbine Propeller Maintenance
Manual
Hartzell Propeller Inc. Manual No. 127 (61-16-27) - Metal
Spinner Assembly Maintenance Manual - Available on the
Hartzell Propeller Inc. website at www.hartzellprop.com
Hartzell Propeller Inc. Manual No. 132A (61-10-32) -
Five-Blade Steel Hub Turbine Propellers
Hartzell Propeller Inc. Manual No. 133C (61-13-33) -
Aluminum Propeller Blade Maintenance Manual
Hartzell Propeller Inc. Manual No. 159 (61-02-59) -
Application Guide - Available on the Hartzell Propeller Inc.
website at www.hartzellprop.com
Hartzell Propeller Inc. Manual 165A (61-00-65) - Illustrated
Tool and Equipment Manual - Available on the Hartzell
Propeller Inc. website at www.hartzellprop.com
Hartzell Propeller Inc. Manual No. 180 (30-61-80) - Propeller
Ice Protection System Manual - Available on the Hartzell
Propeller Inc. website at www.hartzellprop.com
Hartzell Propeller Inc. Manual No. 181 (30-60-81) - Propeller
Ice Protection System Component Maintenance Manual -
Available on the Hartzell Propeller Inc. website at
www.hartzellprop.com
Hartzell Propeller Inc. Manual No. 182 (61-12-82) - Propeller
Electrical De-ice Boot Removal and Installation Manual -
Available on the Hartzell Propeller Inc. website at
www.hartzellprop.com
Hartzell Propeller Inc. Manual No. 183 (61-12-83) - Propeller
Anti-icing Boot Removal and Installation Manual - Available
on the Hartzell Propeller Inc. website at www.hartzellprop.com

Page 1-9
INTRODUCTION 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

Hartzell Propeller Inc. Manual No. 202A (61-01-02) -

Standard Practices Manual, Volumes 1 through 11
(Volume 7, Consumable Materials is available on the Hartzell
Propeller Inc. website at www.hartzellprop.com)
Hartzell Propeller Inc. Service Letter HC-SL-61-61Y -
Overhaul Periods and Service Life Limits for Hartzell
Propellers Inc. Aviation Components - Propellers, Governors,
and Propeller Damper Assemblies - Available on the Hartzell
Propeller Inc. website at www.hartzellprop.com
7. Definitions
A basic understanding of the following terms will assist in
maintaining and operating Hartzell Propeller Inc. propeller
systems.
Term Definition

Annealed ��������������������� Softening of material due to

overexposure to heat
Blade Angle ����������������� Measurement of blade airfoil
location described as the angle
between the blade airfoil and the
surface described by propeller
rotation
Brinelling ����������������������� A depression caused by failure of
the material in compression
Chord ��������������������������� A straight line distance between
the leading and trailing edges of an
airfoil
Cold Rolling ����������������� Compressive rolling process for the
retention area of single shoulder
blades that provides improved
strength and resistance to fatigue
Constant Force ������������� A force that is always present in
some degree when the propeller is
operating
Constant Speed ����������� A propeller system that employs
a governing device to maintain a
selected engine RPM

Page 1-10
INTRODUCTION 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

Term Definition

Corrosion ��������������������� Gradual material removal or

deterioration due to chemical action
Crack ��������������������������� Irregularly shaped separation within
a material, sometimes visible as a
narrow opening at the surface
Depression ������������������� Surface area where the material has
been compressed but not removed
Distortion ��������������������� Alteration of the original shape or
size of a component
Erosion ������������������������� Gradual wearing away or
deterioration due to action of the
elements
Exposure ��������������������� Leaving material open to action of
the elements
Feathering ������������������� The capability of blades to be
rotated parallel to the relative wind,
thus reducing aerodynamic drag
Gouge ��������������������������� Surface area where material has
been removed
Hazardous Propeller ����� The hazardous propeller effects
Effect are defined in Title 14 CFR section
35.15(g)(1)
Horizontal Balance ������� Balance between the blade tip and
the center of the hub
Impact Damage ����������� Damage that occurs when the
propeller blade or hub assembly
strikes, or is struck by, an object
while in flight or on the ground
Major Propeller Effect ��� The major propeller effects are
defined in Title 14 CFR section
35.15(g)(2)
Nick ����������������������������� Removal of paint and possibly a
small amount of material

Page 1-11
INTRODUCTION 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

Term Definition

Onspeed ����������������������� Condition in which the RPM

selected by the pilot through the
propeller control lever and the actual
engine (propeller) RPM are equal
Overhaul ����������������������� The periodic disassembly,
inspection, repair, refinish, and
reassembly of a propeller assembly
to maintain airworthiness
Overspeed ������������������� Condition in which the RPM of
the propeller or engine exceeds
predetermined maximum limits;
the condition in which the engine
(propeller) RPM is higher than the
RPM selected by the pilot through
the propeller control lever
Overspeed Damage ����� Damage that occurs when the
propeller hub assembly rotates at
a speed greater than the maximum
limit for which it is designed
Pitch ����������������������������� Same as “Blade Angle”
Pitting ��������������������������� Formation of a number of small,
irregularly shaped cavities in surface
material caused by corrosion or
wear
Propeller Critical Parts � A part on the propeller whose
primary failure can result in a
hazardous propeller effect, as
determined by the safety analysis
required by Title 14 CFR section
35.15
Reversing ��������������������� The capability of rotating blades to
a position to generate reverse thrust
to slow the aircraft or back up
Scratch ������������������������� Same as “Nick”

Page 1-12
INTRODUCTION 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

Term Definition

Single Acting ����������������� Hydraulically actuated propeller that

utilizes a single oil supply for pitch
control
Superseded ����������������� Parts that are considered airworthy
for continued flight but may no
longer be available
Synchronizing ��������������� Adjusting the RPM of all the
propellers of a multi-engine aircraft
to the same RPM
Synchrophasing ����������� A form of propeller sychronization
in which not only the RPM of the
engines (propellers) are held
constant, but also the position of the
propellers in relation to each other
Track ����������������������������� In an assembled propeller, a
measurement of the location of
the blade tip with respect to the
plane of rotation, used to verify face
alignment and to compare blade tip
location with respect to the locations
of the other blades in the assembly
Underspeed ����������������� The condition in which the actual
engine (propeller) RPM is lower
than the RPM selected by the pilot
through the propeller control lever
Variable Force ������������� A force that may be applied or
removed during propeller operation
Vertical Balance ����������� Balance between the leading
and trailing edges of a two-blade
propeller with the blades positioned
vertically
Windmilling ������������������� The rotation of an aircraft propeller
caused by air flowing through it
while the engine is not producing
power

Page 1-13
INTRODUCTION 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

8. Abbreviations

Abbreviation Term

AMM ����������������������������� Aircraft Maintenance Manual

AN ��������������������������������� Air Force-Navy (or Army-Navy)
AOG ����������������������������� Aircraft on Ground
FAA ������������������������������� Federal Aviation Administration
FT-Lb ��������������������������� Foot-Pound
ICA ������������������������������� Instructions for Continued
Airworthiness
ID ��������������������������������� Inside Diameter
In-Lb ����������������������������� Inch-Pound
IPS . . . . . . . . . . . . . . . . Inches Per Second
Lbs ������������������������������� Pounds
MIL-X-XXX ������������������� Military Specification
MPI ������������������������������� Major Periodic Inspection (Overhaul)
MS ������������������������������� Military Standard
MSDS ��������������������������� Material Safety Data Sheet
OD ������������������������������� Outside Diameter
NAS ����������������������������� National Aerospace Standards
NASM ��������������������������� National Aerospace Standards,
Military
N•m ������������������������������� Newton-Meters
POH ����������������������������� Pilot’s Operating Handbook
PSI ������������������������������� Pounds per Square Inch
RPM ����������������������������� Revolutions per Minute
TBO ����������������������������� Time Between Overhaul
TC ��������������������������������� Type Certificate
TSN ����������������������������� Time Since New
TSO ����������������������������� Time Since Overhaul
NOTE: TSN/TSO is considered as the time accumulated
between rotation and landing, i.e., flight time.

Page 1-14
INTRODUCTION 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

9. Hartzell Propeller Inc. Product Support

Hartzell Propeller Inc. is ready to assist you with questions
concerning your propeller system. Hartzell Propeller Inc. Product
Support may be reached during business hours (8:00 a.m.
through 5:00 p.m., United States Eastern Time) at
(937) 778-4379 or at (800) 942-7767, toll free from the United
States and Canada. Hartzell Product Support can also be
reached by fax at (937) 778-4391, and by email at
[email protected].
After business hours, you may leave a message on our
24 hour product support line at (937) 778-4376 or at
(800) 942-7767, toll free from the United States and Canada. A
technical representative will contact you during normal business
hours. Urgent AOG support is also available 24 hours per day,
seven days per week via this message service.
Additional information is available on our website at
www.hartzellprop.com.
NOTE: When calling from outside the United States, dial (001)
before dialing the above telephone numbers.
10. Warranty Service
If you believe you have a warranty claim, it is necessary to
contact Hartzell Propeller’s Warranty Administrator. Hartzell
Propeller’s Warranty Administrator will provide you with a
Warranty Application form. It is necessary to complete this form
and return it to the Warranty Administrator for evaluation before
proceeding with repair or inspection work. Upon receipt of
this form, the Warranty Administrator will provide instructions on
how to proceed. Hartzell Propeller Inc. Warranty may be reached
during business hours (8:00 a.m. through 5:00 p.m., United
States Eastern Time) at 937-778-4380, or toll free at
(800) 942-7767. Hartzell Propeller Inc. Warranty Administration
can also be reached by fax, at (937) 778-4391, or by email at
[email protected].
NOTE: When calling from outside the United States, dial (001)
before dialing the above telephone numbers.

Page 1-15
INTRODUCTION 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

11. Hartzell Propeller Inc. Recommended Facilities

A. Hartzell Propeller Inc. recommends using Hartzell Propeller
Inc. approved distributors and repair facilities for the
purchase, repair and overhaul of Hartzell Propeller Inc.
propeller assemblies or components.
B. Information about the Hartzell Propeller Inc. worldwide
network of aftermarket distributors and approved repair
facilities is available on the Hartzell Propeller Inc. website at
www.hartzellprop.com.

Page 1-16
INTRODUCTION 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

DESCRIPTION AND OPERATION - CONTENTS

1. Functional Description of Constant Speed Propeller Types........2-5

A. Feathering Propellers HC-B(3,5)( )( )-2( )..............................2-5
B. Feathering and Reversing Propellers
HC-B(3,4,5)( )( )-3( ) Series (External Beta System).............2-9
C. Feathering and Reversing Propellers
HC-B(3,4,5)( )( )-5( ) Series (Internal Beta System)............2-17
D. Feathering and Reversing Propellers
HC-( )3( )( )-7( ) Series (Beta Valve System).......................2-24
2. Model Designation....................................................................2-28
A. Steel Hub Propeller Model Identification..............................2-28
B. Aluminum Blade Model Identification...................................2-31
3. Governors.................................................................................2-33
A. Theory of Operation.............................................................2-33
4. Propeller Ice Protection Systems..............................................2-36
A. Propeller Anti-ice System.....................................................2-36
B. Propeller De-ice System......................................................2-37

Page 2-1
DESCRIPTION AND OPERATION 61-00-39 Rev. 12 Mar/13
 Propeller Owner’s Manual
139

LIST OF FIGURES

HC-B(3,5)( )( )-2( ) Propeller Assembly........... Figure 2-1...............2-4

Steel Hub Unit................................................. Figure 2-2...............2-5
HC-B(3,4,5)( )( )-3( ) Propeller Assembly........ Figure 2-3...............2-8
Start Lock Unit on HC-B(3,4,5)( )( )-3( )
Propeller Assembly................................... Figure 2-4.............2-12
HC-B(3,4)( )( )-5( ) Propeller Assembly with
One-piece Spinner Mounting Plate
(Superseded Configuration)...................... Figure 2-5.............2-14
HC-B3( )( )-5( ) Propeller Assembly with
Two-piece Spinner Mounting Plate
(New Configuration).................................. Figure 2-6.............2-15
HC-B(4,5)( )( )-5( ) Propeller Assembly with
Two-piece Spinner Mounting Plate
(New Configuration).................................. Figure 2-7.............2-16
HC-A3VF-7( ) Propeller Assembly................... Figure 2-8.............2-22
HC-A3MVF-7( ) and HC-B3TF-7( )
Propeller Assembly................................... Figure 2-9.............2-23
Governor in Onspeed Condition..................... Figure 2-10............2-32
Governor in Underspeed Condition................ Figure 2-11............2-32
Governor in Overspeed Condition.................. Figure 2-12............2-32
Feathering Governor...................................... Figure 2-13............2-34
Synchronizer/Synchrophaser Governor......... Figure 2-14............2-34

Page 2-2
DESCRIPTION AND OPERATION 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

(This page is intentionally blank.)

Page 2-3
DESCRIPTION AND OPERATION 61-00-39 Rev. 10 Jun/11
 Note: This picture depicts W10072
BLADE PILOT TUBE
two different spinner
assemblies.
RETENTION BEARING

HUB CYLINDER

SPRING

MOUNTING WASHER
FEATHERING
STOP SCREW
MOUNTING BOLT

DESCRIPTION AND OPERATION

SPINNER DOME

PISTON
139

PISTON NUT
LINK ARM
GREASE FITTING
COUNTERWEIGHT

61-00-39
BLADE CLAMP
Propeller Owner’s Manual

SPINNER BULKHEAD

HC-B(3,5)( )( )-2( ) Propeller Assembly

Figure 2-1

Rev. 7 Oct/02
Page 2-4
 Propeller Owner’s Manual
139

1. Functional Description of Constant Speed Propeller Types

A. Feathering Propellers HC-B(3,5)( )( )-2( )
Refer to Figure 2-1. The propellers described in this section
are constant speed, feathering, and non-reversing. They use
a single oil supply from a governing device to hydraulically
actuate a change in blade angle. The propellers can have
three or five blades, and they are used primarily on Pratt and
Whitney turbine engines.
Propeller blades and bearing assemblies are mounted on the
arms of a steel hub unit (Figure 2-2) and are held in place by
two-piece blade clamps. A cylinder is threaded onto the hub,
and a feathering spring assembly is installed in the cylinder.
A piston is placed over the cylinder and is connected by a
link arm to each blade clamp. Propeller blade angle change
is accomplished through the linear motion of the hydraulically
actuated piston that is transmitted to each blade through the
link arms and blade clamps.

APS2063

Steel Hub Unit

Figure 2-2

Page 2-5
DESCRIPTION AND OPERATION 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

While the propeller is operating, the following forces are

constantly present: 1) spring force, 2) counterweight force,
3) centrifugal twisting moment of each blade, and 4) blade
aerodynamic twisting forces. The spring and counterweight
forces attempt to rotate the blades to higher blade angle,
while the centrifugal twisting moment of each blade is
generally toward lower blade angle. Blade aerodynamic
twisting force is usually very small in relation to the other
forces and can attempt to increase or decrease blade angle.
The summation of the propeller forces is toward higher
pitch (low RPM) and is opposed by a variable force toward
lower pitch (high RPM). The variable force is oil under
pressure from a governor with an internal pump, which
is mounted on and driven by the engine. The oil from the
governor is supplied to the propeller and hydraulic piston
through a hollow engine shaft. Increasing the volume of oil
within the piston and cylinder will decrease the blade angle
and increase propeller RPM. Decreasing the volume of oil
will increase blade angle and decrease propeller RPM. By
changing the blade angle, the governor can vary the load on
the engine and maintain constant engine RPM (within limits),
independent of where the power lever is set. The governor
uses engine speed sensing mechanisms that allow it to
supply or drain oil as necessary to maintain constant engine
speed (RPM).
If governor supplied oil is lost during operation, the propeller
will increase pitch and feather. Feathering occurs because
the summation of internal propeller forces causes the oil to
drain out of the propeller until the feather stop position is
reached.
Normal in-flight unfeathering is accomplished when the pilot
positions the propeller condition lever into the normal flight
(governing) range and restarts the engine. As engine speed
increases, the governor supplies oil to the propeller, and the
blade angle decreases.

Page 2-6
DESCRIPTION AND OPERATION 61-00-39 Rev. 7 Oct/02
 Propeller Owner’s Manual
139

(This page is intentionally blank.)

Page 2-7
DESCRIPTION AND OPERATION 61-00-39 Rev. 7 Oct/02
 BLADE W10075
PILOT TUBE
SPINNER BULKHEAD

RETENTION BEARING
HUB

MOUNTING WASHER CYLINDER

SPRING
MOUNTING BOLT
FEATHERING
STOP SCREW

CARBON BLOCK
ASSEMBLY

SPINNER DOME

DESCRIPTION AND OPERATION

BETA RING

PISTON NUT
PISTON
139

GREASE FITTING
ROD END RING
LINK ARM

61-00-39
BETA ROD UNIT
Propeller Owner’s Manual

BLADE CLAMP
COUNTERWEIGHT

HC-B(3,4,5)( )( )-3( ) Propeller Assembly

Figure 2-3

Rev. 7 Oct/02
Page 2-8
 Propeller Owner’s Manual
139

B. Feathering and Reversing Propellers

HC-B(3,4,5)( )( )-3( ) Series (External Beta System)
Refer to Figure 2-3. The propellers described in this section
are constant speed, feathering and reversing. They use a
single oil supply from a governing device to hydraulically
actuate a change in blade angle. The propellers can have
three, four, or five blades, and they are used primarily on
Pratt and Whitney and Walter turbine engines.
Propeller blades and bearing assemblies are mounted on the
arms of a steel hub unit (Figure 2-2) and are held in place by
two-piece blade clamps. A cylinder is threaded onto the hub,
and a feathering spring assembly is installed in the cylinder.
A piston is placed over the cylinder and is connected by a
link arm to each blade clamp. Propeller blade angle change
is accomplished through the linear motion of the hydraulically
actuated piston that is transmitted to each blade through the
link arms and blade clamps.
While the propeller is operating, the following forces are
constantly present: 1) spring force, 2) counterweight
force, 3) centrifugal twisting moment of each blade, and
4) blade aerodynamic twisting forces. The spring and
counterweight forces attempt to rotate the blades to higher
blade angle, while the centrifugal twisting moment of each
blade is generally acting toward lower blade angle. Blade
aerodynamic twisting force is usually very small in relation
to the other forces and can attempt to increase or decrease
blade angle.

Page 2-9
DESCRIPTION AND OPERATION 61-00-39 Rev. 7 Oct/02
 Propeller Owner’s Manual
139

The summation of the propeller forces is toward higher

pitch (low RPM) and is opposed by a variable force toward
lower pitch (high RPM). The variable force is oil under
pressure from a governor with an internal pump, which
is mounted on and driven by the engine. The oil from the
governor is supplied to the propeller and hydraulic piston
through a hollow engine shaft. Increasing the volume of oil
within the piston and cylinder will decrease the blade angle
and increase propeller RPM. Decreasing the volume of oil
will increase blade angle and decrease propeller RPM. By
changing the blade angle, the governor can vary the load on
the engine and maintain constant engine RPM (within limits),
independent of where the power lever is set. The governor
uses engine speed sensing mechanisms that allow it to
supply or drain oil as necessary to maintain constant engine
speed (RPM).
If governor supplied oil is lost during operation, the propeller
will increase pitch and feather. Feathering occurs because
the summation of internal propeller forces causes the oil to
drain out of the propeller until the feather stop position is
reached.
Normal in-flight feathering is accomplished when the pilot
retards the propeller condition lever past the feather detent.
This allows control oil to drain from the propeller and
return to the engine sump. Engine shutdown is normally
accomplished during the feathering process.
Normal in-flight unfeathering is accomplished when the pilot
positions the propeller condition lever into the normal flight
(governing) range and restarts the engine. As engine speed
increases, the governor supplies oil to the propeller, and the
blade angle decreases.

Page 2-10
DESCRIPTION AND OPERATION 61-00-39 Rev. 7 Oct/02
 Propeller Owner’s Manual
139

In reverse mode of operation, the governor operates in

an underspeed condition to act strictly as a source of
pressurized oil, without attempting to control RPM. Control of
the propeller blade angle in reverse is accomplished through
the beta valve.
NOTE: The beta valve is normally built into the base of the
governor.
The propeller is reversed by manually repositioning the
cockpit-control to cause the beta valve to supply oil from
the governor pump to the propeller. An external propeller
feedback mechanism, which include a beta ring and carbon
block assembly, communicate propeller blade angle position
to the beta valve.
When the propeller reaches the desired reverse position,
movement of the beta ring and carbon block assembly,
initiated by the propeller piston, causes the beta valve
to shut off the flow of oil to the propeller. Any additional
unwanted movement of the propeller toward reverse, or any
movement of the manually positioned beta valve control
toward high pitch position will cause the beta valve to drain
oil from the propeller to increase pitch.
With some applications, it is undesirable to feather the
propeller when the engine is stopped after landing the
aircraft.
To prevent feathering during normal engine shutdown, the
propeller incorporates spring-energized latch pins called
start lock units (Figure 2-4). These units are installed either
on a two-piece spinner mounting plate or on the spinner
bulkhead, which is bolted to the propeller hub flange. If
propeller rotation is approximately 800 RPM or above,
the start lock units are disengaged from the blade clamp
mounted plates by centrifugal force acting on the latch pins
to compress the springs (within the units). When the RPM
drops below 800, the springs overcome the centrifugal force
and move the latch pins to engage the clamp-mounted plate,
preventing blade angle movement to feather.

Page 2-11
DESCRIPTION AND OPERATION 61-00-39 Rev. 7 Oct/02
 Propeller Owner’s Manual
139

Shortly after engine start-up, with the propeller RPM above

800, the latch pins in the start lock units will still retain the
blade angle. To release the latch pins, it is necessary to
manually actuate the propeller slightly toward reverse. This
will move the clamp-mounted plate, allowing the latch pins to
slide freely. Centrifugal force will compress the springs and
disengage the pins from the plate.

W10076

Start Lock Unit on HC-B(3,4,5)( )( )-3( )

Propeller Assembly
Figure 2-4

Page 2-12
DESCRIPTION AND OPERATION 61-00-39 Rev. 7 Oct/02
 Propeller Owner’s Manual
139

(This page is intentionally blank.)

Page 2-13
DESCRIPTION AND OPERATION 61-00-39 Rev. 7 Oct/02
 W10074
BLADE PILOT TUBE

RETENTION BEARING
HUB

CYLINDER

SPRING
START LOCK UNIT
FEATHERING
STOP SCREW

MOUNTING WASHER
SPINNER DOME

MOUNTING BOLT

SPINNER MOUNTING
PLATE PITCH CHANGE ROD

DESCRIPTION AND OPERATION

BETA VALVE TUBE
139

GREASE FITTING (INSIDE PITCH CHANGE ROD;

SUPPLIED WITH ENGINE)
PISTON

61-00-39
LINK ARM PISTON NUT
SPINNER BULKHEAD
COUNTERWEIGHT
Propeller Owner’s Manual

BLADE CLAMP

HC-B(3,4)( )( )-5( ) Propeller Assembly with One-piece Spinner Mounting Plate

(Superseded Configuration)

Page 2-14
Rev. 7 Oct/02
Figure 2-5
 W10073
Note: This illustration
BLADE PILOT TUBE
depicts two different
spinner assemblies.
SPINNER BULKHEAD RETENTION BEARING

CYLINDER
HUB

SPRING
MOUNTING WASHER FEATHERING
STOP SCREW
MOUNTING BOLT

SPINNER MOUNTING SPINNER DOME

PLATE

COUNTERWEIGHT
PITCH CHANGE ROD

DESCRIPTION AND OPERATION

139

GREASE FITTING BETA VALVE TUBE

(INSIDE PITCH CHANGE ROD;
SUPPLIED WITH ENGINE)

PISTON NUT

61-00-39
PISTON
LINK ARM
Propeller Owner’s Manual

BLADE CLAMP GUIDE COLLAR

START LOCK UNIT

HC-B3( )( )-5( ) Propeller Assembly with Two-piece Spinner Mounting Plate (New Configuration)

Page 2-15
Rev. 7 Oct/02
Figure 2-6
 W10100
BLADE PILOT TUBE

RETENTION BEARING
HUB

CYLINDER

SPRING
START LOCK UNIT
FEATHERING
STOP SCREW

MOUNTING WASHER

SPINNER DOME
MOUNTING BOLT

PITCH CHANGE ROD

DESCRIPTION AND OPERATION

SPINNER MOUNTING
PLATE
BETA VALVE TUBE
139

GREASE FITTING (INSIDE PITCH CHANGE ROD;

SUPPLIED WITH ENGINE)
PISTON

61-00-39
LINK ARM PISTON NUT
SPINNER BULKHEAD
COUNTERWEIGHT
Propeller Owner’s Manual

BLADE CLAMP

HC-B(4,5)( )( )-5( ) Propeller Assembly with Two-piece Spinner Mounting Plate (New Configuration)
Figure 2-7

Page 2-16
Rev. 7 Oct/02
 Propeller Owner’s Manual
139

C. Feathering and Reversing Propellers

HC-B(3,4,5)( )( )-5( ) Series (Internal Beta System)
Refer to Figures 2-5 through 2-7. The propellers described
in this section are constant speed, feathering and reversing.
They use a single oil supply from a governing device to
hydraulically actuate a change in blade angle. The propellers
can have three, four, or five blades, and are used primarily
on Garrett (Allied Signal) turbine engines.
Propeller blades and bearing assemblies are mounted on the
arms of a steel hub unit (Figure 2-2) and are held in place by
two-piece blade clamps. A cylinder is threaded onto the hub,
and a feathering spring assembly is installed in the cylinder.
A piston is placed over the cylinder and is connected by a
link arm to each blade clamp. Propeller blade angle change
is accomplished through the linear motion of the hydraulically
actuated piston that is transmitted to each blade through the
link arms and blade clamps.
While the propeller is operating, the following forces are
constantly present: 1) spring force, 2) counterweight force,
3) centrifugal twisting moment of each blade, and 4) blade
aerodynamic twisting forces. The spring and counterweight
forces attempt to rotate the blades to higher blade angle,
while the centrifugal twisting moment of each blade is
generally toward lower blade angle. Blade aerodynamic
twisting force is usually very small in relation to the other
forces and can attempt to increase or decrease blade angle.

Page 2-17
DESCRIPTION AND OPERATION 61-00-39 Rev. 7 Oct/02
 Propeller Owner’s Manual
139

The summation of the propeller forces is toward higher

pitch (low RPM) and is opposed by a variable force toward
lower pitch (high RPM). The variable force is oil under
pressure from a governor with an internal pump, which
is mounted on and driven by the engine. The oil from the
governor is supplied to the propeller and hydraulic piston
through a hollow engine shaft. Increasing the volume of oil
within the piston and cylinder will decrease the blade angle
and increase propeller RPM. Decreasing the volume of oil
will increase blade angle and decrease propeller RPM. By
changing the blade angle, the governor can vary the load on
the engine and maintain constant engine RPM (within limits),
independent of where the power lever is set. The governor
uses engine speed sensing mechanisms that allow it to
supply or drain oil as necessary to maintain constant engine
speed (RPM).
If governor supplied oil is lost during operation, the propeller
will increase pitch and feather. Feathering occurs because
the summation of internal propeller forces causes the oil to
drain out of the propeller until the feather stop position is
reached.
Normal in-flight feathering is accomplished when the pilot
places the propeller condition lever into feather position. This
allows control oil to drain from the propeller and return to the
engine sump. Engine shutdown is normally accomplished
during the feathering process.
Normal in-flight unfeathering is accomplished when the pilot
positions the propeller condition lever into the normal flight
(governing) range, activates the auxiliary pump to decrease
blade pitch, and restarts the engine. As engine speed
increases, the governor supplies oil to the propeller, and the
blade angle decreases until it reaches an onspeed condition.

Page 2-18
DESCRIPTION AND OPERATION 61-00-39 Rev. 7 Oct/02
 Propeller Owner’s Manual
139

In reverse mode of operation, the governor operates in

an underspeed condition to act strictly as a source of
pressurized oil, without attempting to control RPM. Control of
the propeller blade angle in reverse is accomplished through
the beta valve.
NOTE: The beta valve is normally located on the side of
the gearbox opposite the propeller.
The propeller is reversed by manually repositioning the
power lever within the beta range to cause the beta valve to
supply oil from the governor pump to the propeller. A beta
rod inserted into the front of the propeller communicates
propeller blade angle position to the beta valve. When the
propeller reaches the desired reverse position, movement of
the beta rod causes the beta valve to shut off the flow of oil
to the propeller. Any additional unwanted movement of the
propeller toward reverse, or any movement of the manually
positioned beta valve control toward high pitch position
will cause the beta valve to drain oil from the propeller to
increase pitch.
It is undesirable to feather the propeller when the engine
is stopped after landing the aircraft. This propeller type is
normally installed on a fixed shaft engine that causes the
propeller to rotate during an engine start process. If the
propeller is in feather position, an overload on the electric
engine starter will occur.
To prevent feathering during normal engine shutdown, the
propeller incorporates spring-energized latch pins called
start lock units. These units are installed either on a two-
piece spinner mounting plate or on the spinner bulkhead,
which is bolted to the propeller hub flange. If propeller
rotation is approximately 800 RPM or above, the start lock
units are disengaged from the blade clamp mounted plates
by centrifugal force acting on the latch pins to compress the
springs (within the units). When the RPM drops below 800,
the springs overcome the centrifugal force and move the
latch pins to engage the clamp-mounted plate, preventing
blade angle movement to feather.

Page 2-19
DESCRIPTION AND OPERATION 61-00-39 Rev. 7 Oct/02
 Propeller Owner’s Manual
139

CAUTION: RELEASING THE START LOCKS AT

SIGNIFICANTLY HIGHER THAN 800 RPM
OR AT HIGH RPM CAN CAUSE DAMAGE
TO THE START LOCKS.
Shortly after engine start-up, with the propeller RPM above
800, the latch pins in the start lock units will still retain the
blade angle. To release the latch pins, it is necessary to
manually actuate the propeller slightly toward reverse. This
will move the clamp-mounted plate, allowing the latch pins to
slide freely. Centrifugal force will compress the springs and
disengage the pins from the plate.
Hartzell Propeller Inc. -5 series propellers incorporated
various start lock unit configurations.
(1) Certain three-bladed and four-bladed propellers
incorporate a one-piece spinner mounting plate that is
pinched between the hub and engine flanges. The start
lock units are installed on the spinner bulkhead.
NOTE: The one-piece spinner mounting plate was
superseded by a two-piece spinner mounting
plate on current production propellers.
(2) Current production of four-bladed and five-bladed
propellers incorporate a two-piece spinner mounting
plate that bolts onto the propeller hub flange. The start
lock units are installed onto the spinner mounting plate.
(3) Current production of three-bladed propellers incorporate
a two-piece spinner mounting plate that bolts onto the
propeller hub flange. The start lock units are mounted on
the guide collar.

Page 2-20
DESCRIPTION AND OPERATION 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

(This page is intentionally blank.)

Page 2-21
DESCRIPTION AND OPERATION 61-00-39 Rev. 7 Oct/02
 W10081
BLADE
PILOT TUBE

RETENTION BEARING
HUB

CYLINDER

SPRING
MOUNTING WASHER

MOUNTING BOLT
SPINNER DOME

ENGINE FLANGE

DESCRIPTION AND OPERATION

COUNTERWEIGHT
139

BETA VALVE

61-00-39
SPINNER BULKHEAD
PISTON NUT
LINK ARM
PISTON
Propeller Owner’s Manual

GREASE FITTING BLADE CLAMP

HC-A3VF-7( ) Propeller Assembly

Figure 2-8

Page 2-22
Rev. 7 Oct/02
 W10082

BLADE PILOT TUBE

RETENTION BEARING
HUB

CYLINDER
SPRING
MOUNTING WASHER

MOUNTING BOLT SPINNER DOME

ENGINE FLANGE

DESCRIPTION AND OPERATION

139

BETA VALVE
COUNTERWEIGHT

PISTON NUT

61-00-39
SPINNER BULKHEAD
PISTON
Propeller Owner’s Manual

LINK ARM
GREASE FITTING BLADE CLAMP

HC-A3MVF-7( ) and HC-B3TF-7( ) Propeller Assembly

Page 2-23
Rev. 7 Oct/02
Figure 2-9
 Propeller Owner’s Manual
139

D. Feathering and Reversing Propellers

HC-( )3( )( )-7( ) Series (Beta Valve System)
Refer to Figures 2-8 and 2-9. The propellers described in
this section are constant speed, feathering and reversing.
They use a single oil supply from a governing device to
hydraulically actuate a change in blade angle. The propellers
have three blades, and are used primarily on Allison
250B17( ) series turbine engines.
Propeller blades and bearing assemblies are mounted on the
arms of a steel hub unit (Figure 2-2) and are held in place by
two-piece blade clamps. A cylinder is threaded onto the hub,
and a feathering spring assembly is installed in the cylinder.
A piston is placed over the cylinder and is connected by a
link arm to each blade clamp. Propeller blade angle change
is accomplished through the linear motion of the hydraulically
actuated piston that is transmitted to each blade through the
link arms and blade clamps.
While the propeller is operating, the following forces are
constantly present: 1) spring force, 2) counterweight force,
3) centrifugal twisting moment of each blade, and 4) blade
aerodynamic twisting forces. The spring and counterweight
forces attempt to rotate the blades to higher blade angle,
while the centrifugal twisting moment of each blade is
generally toward lower blade angle. Blade aerodynamic
twisting force is usually very small in relation to the other
forces and can attempt to increase or decrease blade angle.

Page 2-24
DESCRIPTION AND OPERATION 61-00-39 Rev. 7 Oct/02
 Propeller Owner’s Manual
139

The summation of the propeller forces is toward higher

pitch (low RPM) and is opposed by a variable force toward
lower pitch (high RPM). The variable force is oil under
pressure from a governor with an internal pump, which
is mounted on and driven by the engine. The oil from the
governor is supplied to the propeller and hydraulic piston
through a hollow engine shaft. Increasing the volume of oil
within the piston and cylinder will decrease the blade angle
and increase propeller RPM. Decreasing the volume of oil
will increase blade angle and decrease propeller RPM. By
changing the blade angle, the governor can vary the load on
the engine and maintain constant engine RPM (within limits),
independent of where the power lever is set. The governor
uses engine speed sensing mechanisms that allow it to
supply or drain oil as necessary to maintain constant engine
speed (RPM).
If governor supplied oil is lost during operation, the propeller
will increase pitch and feather. Feathering occurs because
the summation of internal propeller forces causes the oil to
drain out of the propeller until the feather stop position is
reached.
Normal in-flight feathering is accomplished when the pilot
retards the propeller condition lever past the feather detent.
This allows control oil to drain from the propeller and
return to the engine sump. Engine shutdown is normally
accomplished during the feathering process.
Normal in-flight unfeathering is accomplished when the pilot
positions the propeller condition lever into the normal flight
(governing) range, activates the auxiliary pump to decrease
blade pitch, and restarts the engine. As engine speed
increases, the governor supplies oil to the propeller, and the
blade angle decreases.

Page 2-25
DESCRIPTION AND OPERATION 61-00-39 Rev. 7 Oct/02
 Propeller Owner’s Manual
139

In reverse mode of operation, the governor is reset to act as

a source of pressurized oil. Control of the propeller then is
transferred to the beta valve.
The propeller is reversed by manually repositioning the
cockpit-controlled cable to cause the beta valve to port oil
from the governor pump to the propeller.
When the propeller reaches desired reverse position,
movement of the beta feedback system will cause the
beta valve to shut off flow of oil to the propeller. Any further
unwanted movement of the propeller toward reverse or any
movement of the manually positioned cable toward high
pitch position will cause the beta valve to drain oil from the
propeller to increase pitch.

Page 2-26
DESCRIPTION AND OPERATION 61-00-39 Rev. 7 Oct/02
 Propeller Owner’s Manual
139

(This page is intentionally blank.)

Page 2-27
DESCRIPTION AND OPERATION 61-00-39 Rev. 7 Oct/02
 Propeller Owner’s Manual
139

2. Model Designation
The following pages illustrate sample model designations for
Hartzell Propeller Inc. steel hub turbine propeller hub assemblies
and blades. Hartzell Propeller Inc. uses a model designation to
identify specific propeller and blade assemblies.
Example: HC-B5MA-5A/M11276NK-3. A slash mark separates
the propeller and blade designations.
A. Steel Hub Propeller Model Identification
The propeller model designation is impression stamped on
the propeller hub.
HC - B 3 T N - 3 DY
MINOR MODIFICATIONS
SEE NEXT PAGE

2 - CONSTANT SPEED, FEATHERING, PT-6

3 - CONSTANT SPEED, FEATHERING, REVERSING PT-6 &
SPECIFIC DE- LTP101 & M601; EXTERNAL BETA RING
SIGN FEATURES 5 - CONSTANT SPEED, FEATHERING, REVERSING,
INTERNAL BETA SYSTEM, START LOCKS, TPE-331
7 - CONSTANT SPEED, FEATHERING, REVERSING,
ALLISON ENGINES, INTERNAL BETA SYSTEM,
BETA VALVE C-3630( )

BOLT DOWELS NO. OF BOLTS

CIRCLE NO. DIA. OR STUDS
A 5.125 in. 2 5/8 12 (9/16")
F 4.00 in. 2 1/2 6 (1/2")
MOUNTING N 4.25 in. 2 1/2 8 (9/16")
FLANGE P 4.25 in. 4 1/2 8 (9/16")
W 4.25 in. 4 1/2 8 (9/16") *
* HC-B( )( )W-3( ) requires the use of C-7364-2 spacer.

M - TWO NEEDLE BEARINGS, C-1977 CLAMP

T - TWO NEEDLE BEARINGS, C-1301 CLAMP
BASIC SHANK
V - NEEDLE BEARING, C-3 CLAMP, DOUBLE SHOULDER RETENTION
MV - NEEDLE BEARING, D-6831( ) CLAMP,MODIFIED V SHANK, SINGLE
SHOULDER RETENTION

NO. OF BLADES 3, 4, OR 5

A - DOUBLE SHOULDER RETENTION (V SHANK)

BASIC DESIGN SINGLE SHOULDER RETENTION (MV SHANK)
B - SINGLE SHOULDER RETENTION (T and M SHANK)

HC - HARTZELL CONTROLLABLE

Page 2-28
DESCRIPTION AND OPERATION 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

HC - B 3 T N - 3 DY

MINOR MODIFICATIONS

HC-A3VF-7
A - ADDITION OF A-1869 SPACER - NONFEATHERING
B - 838-113 CLAMP ASSEMBLY, B-3663-3 SLUGS (SI 151)

HC-B3TF-7
A - 838-93 CLAMP ASSEMBLY 1835-39 SPINNER, A3491 SPINNER MOUNTING KIT
B - ADDITION OF A-1869 SPACER - NONFEATHERING
C - A-719 WASHERS
L - LEFT HAND ROTATION

HC-B3(T,W)N-2
B - NONPOLISHED SPINNER, SWEARINGEN
L - LEFT HAND ROTATION

HC-B3TN-3
A - 831-23A, -47, -46 SPRING ASSEMBLY 3 SPRINGS, OLD RODS
B - B-3475A-2 LOW STOP ROD UNIT ALTERNATE B-3475-2, B-3002-2
C - SAME AS -3B EXCEPT 831-23A,-47, -46 SPRING ASSEMBLY 3 SPRINGS NEW RODS
D - SAME AS -3C EXCEPT 831-33 SPRING ASSEMBLY
E - SAME AS -3A EXCEPT B-3475A-10 LOW STOP ROD UNIT ALTERNATE B-3475-10, B-3002-10
F - SAME AS -3E EXCEPT 838-88 CLAMP ASSEMBLY (SAME AS -3E EXCEPT COUNTERWEIGHTS)
G - SAME AS -3C EXCEPT 838-88 CLAMP ASSEMBLY (SAME AS -3C EXCEPT COUNTERWEIGHTS)
H - SAME AS -3B EXCEPT COUNTERWEIGHT SLUGS AND COUNTERWEIGHT ANGLE
K - SAME AS -3C EXCEPT EXT. FEATHER STOP (B-1368-14 PISTON)
L - LEFT HAND ROTATION
M - SAME AS -3B EXCEPT EXT. FEATHER STOP (B-1368-14 PISTON)
N - SAME AS -3G EXCEPT EXT. FEATHER STOP (B-1368-14 PISTON)
P - SAME AS -2H EXCEPT EXT. FEATHER STOP (B-1368-14 PISTON)
S - STOP MOUNTING KIT A-3432-3
Y - STOP MOUNTING KIT

HC-B5MA-3
A - SAME AS -3 EXCEPT BLADE ANGLE SETUP
B - SAME AS -3 EXCEPT D-5574P SPINNER ASSEMBLY AND BLADE ANGLE SETUP
C - SAME AS -3 EXCEPT D-5497-1 SPINNER ASSEMBLY AND BLADE ANGLE SETUP
D - SAME AS -3 EXCEPT BLADE ANGLE SETUP
J - SAME AS -3B EXCEPT 838-107 CLAMP ASSEMBLY AND BLADE ANGLE SETUP

HC-B3TN-5
C - PRP-914-21 PILOT TUBE 'O' RING, 831-30, -48, -45 SPRING ASSEMBLY
D - SAME AS -5C EXCEPT 838-71 CLAMP ASSEMBLY
E - SAME AS -5C EXCEPT 1368-12 PISTON ASSEMBLY
F - SAME AS -5D EXCEPT 1368-12 PISTON ASSEMBLY
G - SAME AS -5E EXCEPT A-3757 STOP PLATES AND 831-38, 48, -45 SPRING ASSEMBLY
K - SAME AS -5F EXCEPT 838-95 CLAMP ASSEMBLY AND NO. 831-30 SPRING ASSEMBLY
L - LEFT HAND ROTATION
M - 830-36 OR -37 STOP UNIT FOR -5C, -5E, -5G
N - 830-36 OR -37 STOP UNIT FOR -5D, -5F
P - 830-36, OR -37 STOP UNIT FOR -5K

HC-B3MN-5
L - LEFT HAND ROTATION

HC-B4MN-3
A - 838-103 CLAMP ASSEMBLY
L - LEFT HAND ROTATION

HC-B4MN-5
A - 834-13 STOP COLLAR, A-3495 STOP PLATE, 838-97L CLAMP ASSEMBLY, 832-44L PISTON
ASSEMBLY
L - LEFT HAND ROTATION

Page 2-29
DESCRIPTION AND OPERATION 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

HC - B 3 T N - 3 DY

MINOR MODIFICATIONS, CONTINUED

HC-B4MP-3
A - D-4846P SPINNER ASSEMBLY. 838-109 CLAMP ASSEMBLY
B - B-3334 LOW STOP COLLAR
C - D-5519P SPINNER ASSEMBLY
L - LEFT HAND ROTATION

HC-B4TN-3
A - B-3475-3 LOW STOP ROD UNIT ALTERNATE B-3475-3, B-3002-3, B-3001-3 COLLAR,
OPTIONAL 838-89 CLAMP ASSEMBLY
B - SAME AS -3A EXCEPT B-3334 COLLAR
C - SAME AS -3A EXCEPT 838-105 CLAMP ASSEMBLY
L - LEFT HAND ROTATION

HC-B4TW-3
(NO MINOR MODIFICATIONS APPLY)

HC-B4TN-5
A - MINOR MODIFICATION
C - PRP-914-21 PILOT TUBE 'O' RING (C & subsequent)
D - SAME AS -5CL EXCEPT 838-92 CLAMP
E - SAME AS -5D EXCEPT 838-98 CLAMP & SPINNER
F - SAME AS -5C EXCEPT 830-34 STOP UNIT
G - SAME AS -5D EXCEPT A-3495 STOP PLATE, 830-34 STOP UNIT
H - SAME AS -5EL EXCEPT A-3495 STOP PLATE
J - SAME AS -5G EXCEPT 832-44 PISTON ASSEMBLY
K - SAME AS -5H EXCEPT 832-44 PISTON ASSEMBLY
L - LEFT HAND ROTATION
M - SAME AS -5J EXCEPT D-3434-7P SPINNER ASSEMBLY
N - SAME AS -5K EXCEPT BLADES AND COUNTERWEIGHT

HC-B5MP-3
A - C-3317-121 PILOT TUBE O-RING, A880-2A PISTON NUT, 831-50 SPRING ASSEMBLY,
832-39 PISTON ASSEMBLY, 834-19 GUIDE COLLAR, C-4019-1 LOW STOP COLLAR
B - SAME AS -3A EXCEPT 831-51 SPRING ASSEMBLY
C - SAME AS -3A EXCEPT 838-107 CLAMP ASSEMBLY
L - LEFT HAND ROTATION

HC-B5MA-5
A - SAME AS -5 EXCEPT BLADE ANGLE SETUP

Page 2-30
DESCRIPTION AND OPERATION 61-00-39 Rev. 10 Jun/11
 Propeller Owner’s Manual
139

B. Aluminum Blade Model Identification

The blade designation is impression stamped on the blade
butt end (internal) and is either on a decal or ink stamped on
the blade camber side (external).

prop model/M11276NK-3

Dash Number (or + number), diameter reduction (or increase) from basic
design. In this example, the nominal 112 inch diameter has been
reduced 3 inches = 109 inch dia. (with some exceptions)
there may be a letter following the dash number:
R - specifically rounded tip
Q - Q-tip, factory 90 degree bent tip
A - slightly thinner & narrower tip fairing
E - elliptical tip

Suffix letters:
A - blade dimensional modification from basic design
B - anti-ice boot (alcohol) or de-ice boot (wire element)
C - blade dimensional modification from basic design
D - blade dimensional modification from basic design
E - de-ice boot (foil element) or internal de-ice element (composite blade)
F - blade dimensional modification from basic design
H - hard alloy (7076)
K - de-ice boot installed (foil element, different PN from B above)
N - shank modification (pilot tube hole)
R - rounded tips
S - square tips or; shot peening of blade surface
blank - original design, no changes

The first 2 or 3 numbers indicate initial design

diameter (in inches), the last 2 numbers indicate
basic model or template (there are some exceptions
to this definition)

Prefix of up to 3 letters:
L - left hand rotation
V,MV,M,P,T - shank design

Page 2-31
DESCRIPTION AND OPERATION 61-00-39 Rev. 10 Jun/11
 Propeller Owner’s Manual
139

APS6149
Pilot Control

Speeder Spring
Flyweights

Pilot Valve

Governor in Onspeed Condition

Figure 2-10
Pilot Control APS6150

Speeder Spring
Flyweights

Pilot Valve

Governor in Underspeed Condition

Figure 2-11
Pilot Control APS6151

Speeder Spring
Flyweights

Pilot Valve

Governor in Overspeed Condition

Figure 2-12

Page 2-32
DESCRIPTION AND OPERATION 61-00-39 Rev. 7 Oct/02
 Propeller Owner’s Manual
139

3. Governors
A. Theory of Operation
(1) A governor is an engine RPM sensing device and high
pressure oil pump. In a constant speed propeller system,
the governor responds to a change in engine RPM by
directing oil under pressure to the propeller hydraulic
cylinder or by releasing oil from the hydraulic cylinder.
The change in oil volume in the hydraulic cylinder
changes the blade angle and maintains the propeller
system RPM to the set value. The governor is set for
a specific RPM via the cockpit propeller control, that
compresses or releases the governor speeder spring.
(2) When the engine is operating at the RPM set by the
pilot using the cockpit control, the governor is operating
onspeed. Refer to Figure 2-10. In an onspeed condition,
the centrifugal force acting on the flyweights is balanced
by the speeder spring, and the pilot valve is neither
directing oil to nor from the propeller hydraulic cylinder.
(3) When the engine is operating below the RPM set by the
pilot using the cockpit control, the governor is operating
underspeed. Refer to Figure 2-11. In an underspeed
condition, the flyweights tilt inward because there is not
enough centrifugal force on the flyweights to overcome
the force of the speeder spring. The pilot valve, forced
down by the speeder spring, meters oil flow to decrease
propeller pitch and raise engine RPM.
(4) When the engine is operating above the RPM set by the
pilot using the cockpit control, the governor is operating
overspeed. Refer to Figure 2-12. In an overspeed
condition, the centrifugal force acting on the flyweights
is greater than the speeder spring force. The flyweights
tilt outward, and raise the pilot valve. The pilot valve
then meters oil flow to increase propeller pitch and lower
engine RPM.

Page 2-33
DESCRIPTION AND OPERATION 61-00-39 Rev. 7 Oct/02
 Propeller Owner’s Manual
139

APS6152
Pilot Control
Lift Rod

Speeder Spring
Flyweights

Pilot Valve

Feathering Governor
Figure 2-13

APS6153

Pilot Control Rod

Coil

Flyweights Speeder Spring

Pilot Valve

Synchronizer/Synchrophaser Governor
Figure 2-14

Page 2-34
DESCRIPTION AND OPERATION 61-00-39 Rev. 7 Oct/02
 Propeller Owner’s Manual
139

(5) Feathering governors allow oil to be pushed from the

propeller to the engine drain to increase propeller pitch
to feather.
Some governors will move the propeller to feather by
actuating a valve that opens to drain the oil supply
between the propeller and governor.
Figure 2-13 illustrates another feathering propeller
governor system. When it is desired to feather the
propeller, the lift rod may be moved by the cockpit
control to mechanically engage the valve. The lifted
valve dumps oil to increase propeller pitch until the
propeller feathers.
(6) A synchronizing system can be employed in a multi-
engine aircraft to keep the engines operating at the
same RPM. A synchrophasing system not only keeps
the RPM of the engines consistent, but also keeps the
propeller blades in phase with each other. Both
synchronizing and synchrophasing systems serve to
reduce noise and vibration.
Synchrophasers installed with turbine propellers
generate an electromagnetic field, either on the rod, or
the flyweights. Figure 2-14 illustrates a governor as a
component of a synchronizing or synchrophasing system
that generates an electromagnetic field on the rod.

Page 2-35
DESCRIPTION AND OPERATION 61-00-39 Rev. 7 Oct/02
 Propeller Owner’s Manual
139

4. Propeller Ice Protection Systems

A Hartzell Propeller Inc. turbine propeller may be equipped with a
an anti-ice or de-ice system. A short description of each of these
systems follows:
A. Propeller Anti-ice System
A propeller anti-ice system is a system that prevents ice
from forming on propeller surfaces. The system dispenses a
liquid (usually isopropyl alcohol) which mixes with moisture
on the propeller blades, reducing the freezing point of the
water. This water/alcohol mixture flows off the blades before
ice forms. This system must be in use before ice forms. It is
ineffective in removing ice that has already formed.
(1) System Overview
(a) A typical anti-ice system consists of a fluid tank,
pump, and distribution tubing.
(b) The rate at which the anti-icing fluid is dispensed is
controlled by a pump speed rheostat in the cockpit.
(c) The anti-icing fluid is dispensed through airframe
mounted distribution tubing and into a rotating
slinger ring mounted on the rear of the propeller hub.
The anti-icing fluid is then directed through blade
feed tubes from the slinger ring onto the blades via
centrifugal force. The anti-icing fluid is directed onto
anti-icing boots that are attached to the leading edge
of the blade. These anti-icing boots evenly distribute
and direct the fluid along the blade leading edge.

Page 2-36
DESCRIPTION AND OPERATION 61-00-39 Rev. 12 Mar/13
 Propeller Owner’s Manual
139

B. Propeller De-ice System

A propeller de-ice system is a system that allows ice to
form, and then removes it by electrically heating the de-ice
boots. The ice partially melts and is thrown from the blade by
centrifugal force.
(1) System Overview
(a) A de-ice system consists of one or more on/off
switches, a timer or cycling unit, a slip ring and
brush blocks, and de-ice boots. The pilot controls
the operation of the de-ice system by turning on one
or more switches. All de-ice systems have a master
switch, and may have another toggle switch for each
propeller. Some systems also have a selector switch
to adjust for light or heavy icing conditions.
(b) The timer or cycling unit determines the sequence of
which blades (or portion thereof) are currently being
de-iced, and for what length of time. The cycling unit
applies power to each de-ice boot or boot segment
in a sequential order.
(c) A brush block, which is normally mounted on the
engine just behind the propeller, is used to transfer
electricity to the slip ring. The slip ring rotates with
the propeller, and provides a current path to the
blade de-ice boots.
(d) De-ice boots contain internal heating elements.
These boots are securely attached to the leading
edges of each blade with adhesive.

Page 2-37
DESCRIPTION AND OPERATION 61-00-39 Rev. 12 Mar/13
 Propeller Owner’s Manual
139

(This page is intentionally blank.)

Page 2-38
DESCRIPTION AND OPERATION 61-00-39 Rev. 12 Mar/13
 Propeller Owner’s Manual
139

INSTALLATION AND REMOVAL - CONTENTS

1. Tools, Consumables, and Expendables......................................3-3

A. Tooling...................................................................................3-3
B. Consumables.........................................................................3-4
C. Expendables..........................................................................3-4
2. Pre-Installation............................................................................3-5
A. Inspection of Shipping Package............................................3-5
B. Uncrating...............................................................................3-5
C. Inspection after Shipment......................................................3-5
D. Reassembly of a Propeller Disassembled for Shipment........3-5
3. Propeller Assembly Installation...................................................3-6
A. Precautions............................................................................3-6
B. Installing HC-B(3, 5)( )( )-2( ) Propeller on the
Aircraft Engine.......................................................................3-7
C. Installing HC-B(3,4,5)( )(A,N,P)-3( ) Propeller on the
Aircraft Engine.....................................................................3-14
D. Installing HC-B(3,4)( )W-3( ) Propeller on the
Aircraft Engine.....................................................................3-20
E. Installing HC-B(3,4)( )( )-5( ) Propeller, with a One-piece
Spinner Mounting Plate, on the Aircraft Engine...................3-31
F. Installing HC-B(3,4,5)( )( )-5( ) Propeller, with a Two-piece
Spinner Mounting Plate, on the Aircraft Engine...................3-35
G. Installing HC-( )3( )( )-7( ) Propeller on the
Allison Engine......................................................................3-40
4. Spinner Dome Installation.........................................................3-50
5. Post-Installation Checks............................................................3-50
6. Spinner Dome Removal............................................................3-51
7. Propeller Assembly Removal....................................................3-52
A. Removal of HC-B(3,5)( )( )-2( ) Propellers...........................3-52
B. Removal of HC-B(3,4,5)( )(A,N,P)-3( ) Propellers...............3-55
C. Removal of HC-B(3,4)( )W-3( ) Propellers...........................3-59
D. Removal of HC-B(3,4,5)( )( )-5( ) Propellers........................3-62
E. Removal of HC-( )3( )( )-7( ) Propellers...............................3-65
F. Removal of Beta Valve Assembly for
HC-( )3( )( )-7( ) Propellers .................................................3-68

Page 3-1
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

INSTALLATION AND REMOVAL - FIGURES

Mounting Bolt and Washer.............................. Figure 3-1...............3-9

Installing Propeller on Engine Flange.............. Figure 3-2.............3-10
Diagram of Torquing Sequence for
Propeller Mounting Bolts........................... Figure 3-3............. 3-11
Determining Torque Value When Using
Torquing Adaptor....................................... Figure 3-4.............3-13
Beta System Puller for Decompressing
-3 Series External Beta System................ Figure 3-5.............3-16
Carbon Block and Beta Ring Clearance.......... Figure 3-6.............3-18
Carbon Block Assembly.................................. Figure 3-7.............3-18
Hub-to-Spacer O-ring Location
in the Spacer............................................. Figure 3-8.............3-22
Installing the HC-B(3,4)( )W-3( ) Propeller
on the Engine Flange................................ Figure 3-9.............3-24
Installing the Washer on the Mounting Stud... Figure 3-10............3-26
One-piece Spinner Mounting Plate
Installation................................................ Figure 3-11............3-30
Beta Valve System......................................... Figure 3-12............3-38
Cross Section View of the Beta Valve
System..................................................... Figure 3-13............3-39
-7( ) Propeller Assembly................................. Figure 3-14............3-42
Spring Assembly to Cylinder
Attachment Details................................... Figure 3-15............3-43
Piston to Link Arm Attachment Details........... Figure 3-16............3-43
Filed Rod for Set Screw................................. Figure 3-17............3-48

INSTALLATION AND REMOVAL - TABLES

Propeller/Engine Flange O-rings...................... Table 3-1................3-8
Propeller Mounting Hardware........................... Table 3-2................3-8
Torque Table..................................................... Table 3-3..............3-12

Page 3-2
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

1. Tools, Consumables, and Expendables

The following tools, consumables, and expendables will be
required for propeller removal or installation:
A. Tooling
Each propeller model requires a calibrated torque wrench,
safety wire pliers (alternate: safety cable tool), and the model
specific tooling listed below:
HC-B3( )(A,N,P)-2( )
• Torque wrench adaptor (Hartzell Propeller Inc.
  P/N AST-2877)
• 5/8 inch deep well socket
• 1-7/16 inch crowfoot wrench
HC-B(3,4,5)( )(A,N,P)-3( )
• Torque wrench adaptor (Hartzell Propeller Inc.
  P/N AST-2877)
• 5/8 inch deep well socket
• 1-7/16 inch crowfoot wrench
• Feeler gage
• Beta system puller (Hartzell Propeller Inc. P/N CST-2987)
HC-B(3,4)( )W-3( )
• Torque wrench adaptor (Hartzell Propeller Inc.
  P/N AST-3175)
• Torque check tool (Hartzell Propeller Inc. P/N AST-2968-1)
• Feeler gage
• Beta system puller (Hartzell Propeller Inc. P/N CST-2987)
• 5/8 inch deep well socket
• 1-7/16 inch crowfoot wrench
HC-B5M( )-2
HC-B(3,4,5)( )-5( )
• Torque wrench adaptor (Hartzell Propeller Inc.
  P/N AST-2877)
• One inch deep well socket
• 1-13/16 inch crowfoot wrench

Page 3-3
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

HC-( )3( )F-7( )

• Torque wrench adaptor (Hartzell Propeller Inc.
  P/N AST-2917)
• 5/8 inch deep well socket
• 1-7/16 inch crowfoot wrench
B. Consumables
• Quick Dry Stoddard Solvent or Methyl-Ethyl-Ketone (MEK)
• Anti-Seize Compound (MIL-PRF-83483)
C. Expendables
• 0.032 inch (0.81 mm) Stainless Steel Aircraft Safety Wire
(Alternate: 0.032 inch [0.81 mm] aircraft safety cable and
associated hardware)
• O-ring, propeller flange (see Table 3-1)
• O-ring, for HC-B(3,4)( )W-3( ) spacer (see Table 3-1)

Page 3-4
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

2. Pre-Installation
A. Inspection of Shipping Package
Examine the exterior of the shipping container for signs of
shipping damage, especially at the box ends around each
blade. A hole, tear, or crushed appearance at the end of
the box (blade tips) may indicate the propeller was dropped
during shipment, possibly damaging the blades.
B. Uncrating
(1) Place the propeller on a firm support.
(2) Remove the banding and any external wood bracing
from the shipping container.
(3) Remove the cardboard from the hub and blades. Place
the propeller on a padded surface that supports the
propeller over a large area. Never stand the propeller on
a blade tip.
(4) Remove the plastic dust cover cup from the propeller
mounting flange (if installed).
C. Inspection after Shipment
After removing the propeller from the shipping container,
examine the propeller components for shipping damage.
CAUTION: TO FACILITATE BOXING AND SHIPPING
OF PROPELLERS, THE PISTON NUT
(A-880-1 OR -2) ON STEEL HUB TURBINE
PROPELLERS MAY BE REMOVED TO
ALLOW ROTATING OF THE BLADES
BEFORE PACKAGING.
NOTE: The ability to rotate the blades
during propeller installation
will allow easier access to the
propeller mounting bolts on -3
propeller models.
D. Reassembly of a Propeller Disassembled for Shipment
If a propeller was received disassembled for shipment, it is to
be reassembled by trained personnel in accordance with the
applicable propeller maintenance manual.

Page 3-5
INSTALLATION AND REMOVAL 61-00-39 Rev. 7 Oct/02
 Propeller Owner’s Manual
139

3. Propeller Assembly Installation

A. Precautions
WARNING 1: DURING ENGINE INSTALLATION OR
REMOVAL, USING THE PROPELLER TO
SUPPORT THE WEIGHT OF THE ENGINE
IS NOT AUTHORIZED. UNAPPROVED
INSTALLATION AND REMOVAL TECHNIQUES
MAY CAUSE DAMAGE TO THE PROPELLER
THAT MAY LEAD TO FAILURE RESULTING IN
AN AIRCRAFT ACCIDENT.

WARNING 2: WHEN INSTALLING THE PROPELLER,

FOLLOW THE AIRFRAME MANUFACTURER’S
MANUALS AND PROCEDURES, AS THEY
MAY CONTAIN ISSUES VITAL TO AIRCRAFT
SAFETY THAT ARE NOT CONTAINED IN THIS
OWNER’S MANUAL.

CAUTION 1: INSTRUCTIONS AND PROCEDURES IN THIS

SECTION MAY INVOLVE CRITICAL PARTS.
REFER TO THE INTRODUCTION CHAPTER
OF THIS MANUAL FOR INFORMATION ABOUT
PROPELLER CRITICAL PARTS. REFER TO
THE ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL MANUAL(S)
FOR THE IDENTIFICATION OF SPECIFIC
PROPELLER CRITICAL PARTS.

CAUTION 2: AVOID THE USE OF BLADE PADDLES.

DO NOT PLACE THE BLADE PADDLE IN
THE AREA OF THE DE-ICE BOOT WHEN
APPLYING TORQUE TO A BLADE ASSEMBLY.
PLACE THE BLADE PADDLE IN THE
THICKEST AREA OF THE BLADE, JUST
OUTSIDE OF THE DE-ICE BOOT. USE ONE
BLADE PADDLE PER BLADE.
(1) Be sure the propeller is removed before the engine is
removed or installed in the airframe.

Page 3-6
INSTALLATION AND REMOVAL 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

(2) Follow the airframe manufacturer’s instructions for

installing the propeller. If such instructions are not in
the airframe manufacturer’s manual, then follow the
instructions in this manual; however, mechanics must
consider that this owner’s manual does not describe
important procedures that are outside the scope of this
manual. In addition to propeller installation procedures,
items such as rigging and preflight testing of flight
idle blade angle, installation and adjustment of de-ice
equipment, and propeller synchronization devices are
normally found in the airframe manufacturer’s manuals.
B. Installing HC-B(3, 5)( )( )-2( ) Propeller on the Aircraft Engine
WARNING: MAKE SURE THE SLING IS RATED UP
TO 800 LBS (363 KG) TO SUPPORT THE
WEIGHT OF THE PROPELLER ASSEMBLY
DURING REMOVAL.

CAUTION 1: INSTRUCTIONS AND PROCEDURES IN

THIS SECTION MAY INVOLVE CRITICAL
PARTS. REFER TO THE INTRODUCTION
CHAPTER OF THIS MANUAL FOR
INFORMATION ABOUT PROPELLER
CRITICAL PARTS. REFER TO THE
ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL
MANUAL(S) FOR THE IDENTIFICATION
OF SPECIFIC PROPELLER CRITICAL
PARTS.

CAUTION 2: WHEN INSTALLING THE PROPELLER

ON THE AIRCRAFT, DO NOT DAMAGE
THE ICE PROTECTION SYSTEM
COMPONENTS, IF APPLICABLE.
(1) With a suitable crane hoist and sling, carefully move
the propeller assembly to the aircraft engine mounting
flange.
(2) Make sure the propeller hub flange and engine flange
mating surfaces are clean.

Page 3-7
INSTALLATION AND REMOVAL 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

(3) Install the specified O-ring on the engine flange. Refer to

Table 3-1.
(4) Align mounting and dowel pin holes in the propeller hub
flange with the mounting holes and dowel pins in the
engine flange.
CAUTION: MAKE SURE THAT COMPLETE AND TRUE
SURFACE CONTACT IS ESTABLISHED
BETWEEN THE PROPELLER HUB
FLANGE AND THE ENGINE FLANGE.
(5) Slide the propeller flange onto the engine flange.

Flange O-ring Part Number

A flange C-3317-239-2
F flange C-3317-228
N/P flange C-3317-230
W flange Hub-to-Engine C-3317-230
HC-B(3,4)( )W-3( ) Hub-to-Spacer C-3317-233
Propeller/Engine Flange O-rings
Table 3-1

Propeller Model Mounting Hardware

HC-B3TF-7( ) A-1328-1 Bolt and A-1381 Washer
HC-B3( )N-( ) B-3339 Bolt and A-2048-2 Washer
HC-B(3,4)( )W-3( ) B-7458 Nut and B-7624 Washer
HC-B4( )( )-( ) B-3339 Bolt and A-2048-2 Washer
HC-B5MA-( ) B-3347 Bolt and A-2048-2 Washer
HC-B5MP-3( ) B-3339 Bolt and A-2048-2 Washer
HC-B5MP-5( ) B-3339-1 Bolt and A-2048-2 Washer

Propeller Mounting Hardware

Table 3-2

Page 3-8
INSTALLATION AND REMOVAL 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

CAUTION: NEW PROPELLER MOUNTING BOLTS

MUST BE USED WHEN INITIALLY
INSTALLING A NEW OR OVERHAULED
PROPELLER.
(6) Apply MIL-PRF-83483 anti-seize compound to the
threaded surfaces of the specified mounting bolts. Refer
to Table 3-2 for appropriate mounting hardware.
(a) If the propeller is removed between overhaul
intervals, mounting bolts and washers may be
reused if they are not damaged or corroded.
CAUTION: ID CHAMFER OF WASHER MUST BE
FACING TOWARD THE BOLT HEAD.
WASHERS WITHOUT CHAMFER MUST
BE INSTALLED WITH ROLLED EDGES
TOWARD THE BOLT HEAD.
(REFER TO FIGURE 3-1).

APS0279C
Chamfer of washer must
face bolt head at installation.
Washers without chamfer must
be installed with rolled edges
Without toward bolt head.
chamfer

With
chamfer

NOTE: Size of chamfer can vary

from washer to washer.

Mounting Bolt and Washer

Figure 3-1

Page 3-9
INSTALLATION AND REMOVAL 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

3040I.TIF
W10077
W10078
W10079 Propeller Flange
W10080
Torque Wrench

Engine Flange

Washer

O-ring

Bolt Torque Wrench

Adaptor*
*Note: If torque wrench adaptor is used, use the calculation in Figure 3-4 to
determine correct torque wrench setting.
A Flange F Flange

Mounting Bolt
Holes (Threaded)

Dowel Pin Holes

(Unthreaded)

Spinner Mounting
Plate Attachment
Holes (Threaded)
N Flange P Flange

Installing Propeller on Engine Flange

Figure 3-2

Page 3-10
INSTALLATION AND REMOVAL 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

A Flange W10107C
W10107B
W10108C
W10109C
W10109B

SEQUENCE A SEQUENCE B
Use Sequence A for steps one and two. Use Sequence B for step three.
Step 1 - Torque all bolts to 40 ft-lbs (54 N•m). Step 3 - Torque all bolts to
Step 2 - Torque all bolts to 80 ft-lbs (108 N•m). Table 3-3.

F Flange

Step 1 -Torque all bolts to 40 ft-lbs (54 N•m).

Step 2 -Torque all bolts to Table 3-3.

N, P or W Flange

SEQUENCE A SEQUENCE B
Use Sequence A for steps one and two. Use Sequence B for step three.
Step 1 - Torque all bolts to 40 ft-lbs (54 N•m). Step 3 - Torque all bolts to
Step 2 - Torque all bolts to 80 ft-lbs (108 N•m). Table 3-3.

Diagram of Torquing Sequence for Propeller Mounting Bolts

Figure 3-3

Page 3-11
INSTALLATION AND REMOVAL 61-00-39 Rev. 8 Dec/06
 Propeller Owner’s Manual
139

(7) Install the mounting bolts with washers through the

engine flange and into the propeller hub flange. Refer to
Figure 3-2.
(8) Use a torque wrench and the specified torque wrench
adaptor (see paragraph 1.A. Tooling in this chapter)
to torque all mounting bolts in sequences and steps
shown in Figure 3-3. Refer to Table 3-3 and Figure 3-4 to
determine the proper torque value.
(9) Safety all mounting bolts with 0.032 inch (0.81 mm)
minimum diameter stainless steel wire or equivalent
aircraft safety cable and associated hardware (two bolts
per safety.)
CAUTION: TO FACILITATE BOXING AND SHIPPING
OF PROPELLERS, THE PISTON NUT
(A-880-1) ON HC-B3( )( )-2( ) STEEL HUB
TURBINE PROPELLERS MAY HAVE BEEN
REMOVED TO ALLOW ROTATING OF THE
BLADES BEFORE PACKAGING.

A flange mounting bolts 100-105 Ft-Lbs (136-142 N•m) wet

F flange mounting bolts 80-90 Ft-Lbs (108-122 N•m)
N/P flange mounting bolts 100-105 Ft-Lbs (136-142 N•m) wet
W flange mounting nuts 120-125 Ft-Lbs (163-170 N•m)
Spinner mounting bolts 30-40 Ft-Lbs (41-54 N•m)
Piston nut (lock nut) 120 Ft-Lbs (163 N•m)*
Guide rod jam nuts 10 Ft-Lbs (14 N•m)*
Lubrication Fitting 4 Ft-Lbs (5 N•m)*

Check Nut (beta valve assembly) 9-11 Ft-Lbs (12-15 N•m)

* Torque tolerance is ± 10 percent unless otherwise noted.

NOTE 1: Torque values are based on non-lubricated threads,
unless otherwise specified.
NOTE 2: Wet torque values denote the use of anti-seize
compound MIL-PRF-83483.
Torque Table
Table 3-3

Page 3-12
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(10)Procedure for reinstallation of piston nut, if applicable.

(a) Following the installation of the propeller, use a
breaker bar and a 5/8 inch deep well socket to hold
the pitch change rod.
(b) Using a 1- 7/16 inch crowfoot wrench and torque
wrench, torque the A-880-1 piston nut. Refer to Table
3-3 and Figure 3-4 for the proper torque value.
NOTE: The removal and subsequent reinstallation
of the piston nut does not require that the
propeller blade angles be re-checked.

APS0212A

Standard Torque Wrench Torquing Adaptor

1.00 foot 0.50 foot

(30.5 cm) (15.2 cm)

(actual torque required) X (torque wrench length) Torque wrench reading

(torque wrench length) + (length of adaptor) = to achieve required actual
torque

EXAMPLE:
reading on torque
100 Ft-Lb (136 N•m) x 1 ft (30.5 cm) 66.7 Ft-Lb wrench with 6-inch
= <
1 ft (30.5 cm) + 0.50 ft (15.2 cm) (90.1 N•m) (15.2 cm) adaptor for
actual torque of 100
Ft-Lb (136 N•m)

The correction shown is for an adapter that is aligned with the centerline of the
torque wrench. If the adapter is angled 90 degrees relative to the torque wrench
centerline, the torque wrench reading and actual torque applied will be equal.

Determining Torque Value When Using Torquing Adaptor

Figure 3-4

Page 3-13
INSTALLATION AND REMOVAL 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

(11) If the propeller is equipped with an ice protection system

that uses components supplied by Hartzell Propeller
Inc., applicable instructions and technical information for
the components supplied by Hartzell Propeller Inc. can
be found in the following publications available on the
Hartzell Propeller Inc. website at www.hartzellprop.com:
(a) Manual 180 (30-61-80) - Propeller Ice Protection
System Manual
(b) Manual 181 (30-60-81) - Propeller Ice Protection
System Component Maintenance Manual
(c) Manual 182 (61-12-82) - Propeller Electrical De-ice
Boot Removal and Installation Manual
(d) Manual 183 (61-12-83) - Propeller Anti-icing Boot
Removal and Installation Manual
(12)Propeller ice protection system components not
supplied by Hartzell Propeller Inc. are controlled by the
applicable TC or STC holder’s Instructions for Continued
Airworthiness (ICA).
C. Installing HC-B(3,4,5)( )(A,N,P)-3( ) Propeller on the Aircraft
Engine
CAUTION: INSTRUCTIONS AND PROCEDURES IN
THIS SECTION MAY INVOLVE CRITICAL
PARTS. REFER TO THE INTRODUCTION
CHAPTER OF THIS MANUAL FOR
INFORMATION ABOUT PROPELLER
CRITICAL PARTS. REFER TO THE
ILLUSTRATED PARTS LIST CHAPTER OF
THE APPLICABLE OVERHAUL MANUAL(S)
FOR THE IDENTIFICATION OF SPECIFIC
PROPELLER CRITICAL PARTS.
NOTE: The use of a fretting disk between the propeller
flange and engine flange is recommended on
certain applications for propeller models
HC-B5MP-3( ). Refer to Hartzell Propeller Inc.
Service Bulletin HC-SB-61-275 information about
affected applications.

Page 3-14
INSTALLATION AND REMOVAL 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

(1) Use a beta system puller CST-2987 (Figure 3-5) to

compress the beta system and pull the beta ring forward
to allow installation of the double hex head propeller
mounting bolts.
WARNING: MAKE SURE THE SLING IS RATED UP
TO 800 LBS (363 KG) TO SUPPORT THE
WEIGHT OF THE PROPELLER ASSEMBLY
DURING INSTALLATION.

CAUTION: WHEN INSTALLING THE PROPELLER

ON THE AIRCRAFT, DO NOT DAMAGE
THE ICE PROTECTION SYSTEM
COMPONENTS, IF APPLICABLE.
(2) With a suitable crane hoist and sling, carefully move the
propeller assembly to the aircraft engine mounting flange.
(3) Make sure the propeller hub flange and the engine
flange mating surfaces are clean.
(4) Install the specified O-ring on the engine flange. Refer to
Table 3-1.
(5) Align the mounting and dowel pin holes in the propeller
hub flange with the mounting holes and dowel pins in the
engine flange.
CAUTION: MAKE SURE THAT COMPLETE AND TRUE
SURFACE CONTACT IS ESTABLISHED
BETWEEN THE PROPELLER HUB
FLANGE AND THE ENGINE FLANGE.
(6) Slide the propeller flange onto the engine flange.
CAUTION: NEW PROPELLER MOUNTING BOLTS
MUST BE USED WHEN INITIALLY
INSTALLING A NEW OR OVERHAULED
PROPELLER.
(7) Apply MIL-PRF-83483 anti-seize compound to the
threaded surfaces of the specified mounting bolts. Refer
to Table 3-2 for appropriate mounting hardware.
NOTE: If the propeller is removed between overhaul
intervals, mounting bolts and washers may be
reused if they are not damaged or corroded.

Page 3-15
INSTALLATION AND REMOVAL 61-00-39 Rev. 11 Jul/12
 W10084

INSTALLATION AND REMOVAL

139

(Hartzell Propeller Inc.

P/N CST-2987)

61-00-39
Propeller Owner’s Manual

Beta System Puller for Decompressing -3 Series External Beta System

Rev. 11 Jul/12
Page 3-16
Figure 3-5
 Propeller Owner’s Manual
139

CAUTION: ID CHAMFER OF THE WASHER MUST

BE FACING TOWARD THE BOLT HEAD.
WASHERS WITHOUT CHAMFER MUST
BE INSTALLED WITH ROLLED EDGES
TOWARD THE BOLT HEAD. (REFER TO
FIGURE 3-1).
(8) Install mounting bolts with washers through the engine
flange and into the propeller hub flange. Refer to
Figure 3-2.
(9) Use a torque wrench and the specified torque wrench
adaptor (see paragraph 1.A. Tooling in this chapter)
to torque all mounting bolts in sequences and steps
shown in Figure 3-3. Refer to Table 3-3 and Figure 3-4 to
determine the proper torque value.
(10)Safety all mounting bolts with 0.032 inch (0.81 mm)
minimum diameter stainless steel wire or equivalent
aircraft safety cable and associated hardware (two bolts
per safety).
(11) Decompress the external beta system and remove the
beta system puller.
CAUTION: THE BETA RING MUST NOT CONTACT ANY
ENGINE COMPONENT OR MOUNTING BOLT
SAFETY WIRE. THE BETA SYSTEM COULD
BE DAMAGED IF IT CONTACTS ANY STATIC
ENGINE COMPONENT WHILE ROTATING.
(12)Examine the beta ring to make sure that it is not in
contact with any engine component or mounting bolt
safety wire.
(a) If there is contact between the beta ring and any
engine component or mounting bolt safety wire,
consult qualified personnel at an appropriately
licensed propeller repair facility.
(13)Install the carbon block into the beta linkage lever
in accordance with the airframe manufacturer’s
instructions.

Page 3-17
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

Snap Ring

Carbon Block
Assembly Side clearance 0.001 to 0.010
inch (0.03 to 0.25 mm) upon
installation.

Beta Ring

APS0168b
Carbon Block and Beta Ring Clearance
Figure 3-6

Snap Ring Cotter Pin

Yoke Unit

Beta Lever

Clevis Pin Block Unit

BPS0041

Carbon Block Assembly

Figure 3-7

Page 3-18
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

CAUTION 1: FIT THE BLOCK IN THE BETA RING WITH

A MINIMUM SIDE CLEARANCE OF 0.001
INCH (0.03 mm). REFER TO FIGURE 3-6.

CAUTION 2: MAXIMUM SIDE CLEARANCE

PERMITTED IS 0.010 INCH (0.25 mm)
IN ACCORDANCE WITH THE CARBON
BLOCK ASSEMBLIES SECTION IN THE
MAINTENANCE PRACTICES CHAPTER
OF THIS MANUAL.
(14)Install the carbon block assembly (Figure 3-7) into the
beta ring.
(15)Install, adjust and safety the beta linkage per the
airframe manufacturer’s instructions.
CAUTION: TO FACILITATE BOXING AND SHIPPING
OF PROPELLERS, THE PISTON NUT
MAY HAVE BEEN REMOVED TO ALLOW
ROTATING OF THE BLADES BEFORE
PACKAGING.
(16)Procedure for reinstallation of piston nut, if applicable.
(a) Following the installation of the propeller, use a
breaker bar and a 5/8 inch deep well socket to hold
the pitch change rod.
(b) Using a 1-7/16 inch crowfoot wrench and torque
wrench, torque the A-880-1 piston nut. Refer to
Table 3-3 and Figure 3-4 for the proper torque value.
NOTE: The removal and subsequent reinstallation
of the piston nut does not require that the
propeller blade angles be re-checked.
(17)If the propeller is equipped with an ice protection system
that uses components supplied by Hartzell Propeller
Inc., applicable instructions and technical information for
the components supplied by Hartzell Propeller Inc. can
be found in the following publications available on the
Hartzell Propeller Inc. website at www.hartzellprop.com:
(a) Manual 180 (30-61-80) - Propeller Ice Protection
System Manual

Page 3-19
INSTALLATION AND REMOVAL 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

(b) Manual 181 (30-60-81) - Propeller Ice Protection

System Component Maintenance Manual
(c) Manual 182 (61-12-82) - Propeller Electrical De-ice
Boot Removal and Installation Manual
(d) Manual 183 (61-12-83) - Propeller Anti-icing Boot
Removal and Installation Manual
(18)Propeller ice protection system components not
supplied by Hartzell Propeller Inc. are controlled by the
applicable TC or STC holder’s Instructions for Continued
Airworthiness (ICA).
D. Installing HC-B(3,4)( )W-3( ) Propeller on the Aircraft Engine
CAUTION 1: INSTRUCTIONS AND PROCEDURES IN
THIS SECTION MAY INVOLVE CRITICAL
PARTS. REFER TO THE INTRODUCTION
CHAPTER OF THIS MANUAL FOR
INFORMATION ABOUT PROPELLER
CRITICAL PARTS. REFER TO THE
ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL
MANUAL(S) FOR THE IDENTIFICATION
OF SPECIFIC PROPELLER CRITICAL
PARTS.

CAUTION 2: WHEN INSTALLING THE

HC-B4TW-3/T10282N PROPELLER ON
THRUSH AIRCRAFT MODELS S2R-H80
OR S2RHG-H80, COMPLIANCE WITH
GE AVIATION SERVICE BULLETIN
H80-100-72-00019 IS REQUIRED.
(1) Use a beta system puller CST-2987 (Figure 3-5) to
compress the beta system and pull the beta ring forward
to allow access to the propeller mounting flange.

Page 3-20
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

WARNING: MAKE SURE THE SLING IS RATED UP

TO 800 LBS (363 KG) TO SUPPORT THE
WEIGHT OF THE PROPELLER ASSEMBLY
DURING INSTALLATION.

CAUTION: WHEN INSTALLING THE PROPELLER

ON THE AIRCRAFT, DO NOT DAMAGE
THE ICE PROTECTION SYSTEM
COMPONENTS, IF APPLICABLE.
(2) With a suitable crane hoist and sling, carefully move
the propeller assembly to the aircraft engine mounting
flange.
CAUTION: IF THE PROPELLER IS REMOVED
BETWEEN OVERHAUL INTERVALS, A
TORQUE CHECK OF THE MOUNTING
STUDS MUST BE PERFORMED.
(3) Unless this is the first installation of a new, or newly
overhauled propeller, perform a torque check of the
propeller mounting studs as follows:
(a) Thread the torque check tool AST-2968-1 onto each
propeller mounting stud and torque to 35 ft-lbs
(47.6 N•m).
(b) Visually inspect each stud for evidence of
movement.
(c) Remove the torque check tool AST-2968-1 while
visually inspecting each stud for evidence of
movement.
(d) If any stud rotates due to either the tightening or
removal of the torque check tool, all studs must be
replaced. Refer to Hartzell Propeller Inc. Standard
Practices Manual 202A (ATA 61-01-02) for stud
replacement procedures.
(4) Make sure the propeller hub flange and the engine
flange mating surfaces are clean.
(5) Install the specified O-ring on the engine flange. Refer to
Table 3-1.
(6) If the C-7364-2 spacer is attached to the propeller hub
with screws, proceed to step 3.D.(8).

Page 3-21
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(7) If the C-7364-2 spacer is not already installed on

the propeller hub perform the following installation
procedures:
(a) If the hub flange does not have two 8-32 threaded
holes to attach the spacer or, if two attachment
screws were not provided, perform the following
steps:
1 Coat the hub-to-spacer O-ring with grease.
Refer to Table 3-1.
2 Install the hub-to-spacer O-ring in the groove in
the spacer that interfaces with the face of the
hub flange. Refer to Figure 3-8.
3 Align the mounting studs and dowel pin holes in
the propeller hub flange with the mounting holes
and dowel pins in the spacer.

W10409
W10410

Attachment Dowel pin Dowel pin

screw hole

O-ring groove

Engine Propeller
Side Side

Attachment
screw hole
Engine Dowel pin
Side Dowel pin

Hub-to-Spacer O-ring Location in the Spacer

Figure 3-8

Page 3-22
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

CAUTION: MAKE SURE THE HUB-TO-SPACER

O-RING STAYS IN THE GROOVE
IN THE SPACER. IF THE O-RING
IS TWISTED OR PINCHED, OIL
LEAKAGE WILL RESULT WHEN
THE PROPELLER IS OPERATED
ON THE AIRCRAFT.
4 Slide the spacer onto the mounting studs and
against the hub flange.
NOTE: If the propeller installation will be
delayed, the spacer and O-ring should
be installed and temporarily held in
place with non-self locking nuts and
a sufficient number of washers on at
least two mounting studs. Remove the
nuts and washers before installation.
(b) If the hub flange has two 8-32 threaded holes
and two MS24693-S2 flat-head screws
(HPI P/N B-3868-S52) are provided to attach the
C-7364-2 spacer, perform the following steps:
1 Coat the hub-to-spacer O-ring with grease.
Refer to Table 3-1.
2 Install the hub-to-spacer O-ring in the groove in
the spacer that interfaces with the face of the
hub flange. Refer to Figure 3-8.
3 Align the spacer attachment holes with the two
8-32 threaded holes in the hub flange.
CAUTION: MAKE SURE THE HUB-TO-SPACER
O-RING STAYS IN THE GROOVE
IN THE SPACER. IF THE O-RING
IS TWISTED OR PINCHED, OIL
LEAKAGE WILL RESULT WHEN
THE PROPELLER IS OPERATED
ON THE AIRCRAFT.
4 Slide the spacer onto the mounting studs and
against the hub flange.

Page 3-23
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

APS6160C.TIF
E-7373i.PLT,
W10079

Torque Wrench
Hub-to-Engine
O-ring

Washer
Propeller
Flange

Hub-to-Spacer
O-ring

Screw
Torque Wrench Nut
Adaptor* Engine Flange

*Note: If torque wrench adaptor is used, use the calculation in Figure 3-4 to
determine correct torque wrench setting.

W Spinner Mounting Plate

Propeller Flange Attachment Holes (10)
(Threaded)
Dowel Pin Holes (4)
(Unthreaded)

Mounting
Studs (8)
Spacer Attachment
Holes (2) (Threaded),
If Present

Installing the HC-B(3,4)( )W-3( ) Propeller on the Engine Flange

Figure 3-9

Page 3-24
INSTALLATION AND REMOVAL 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

5 Insert supplied flat-head screw through each

screw hole in the spacer and into the 8-32
threaded holes in the hub flange. Refer to
Figure 3-9.
CAUTION: MAKE SURE THE FLAT-HEAD
ATTACHMENT SCREWS DO NOT
PROTRUDE ABOVE THE ENGINE-
SIDE SURFACE OF THE SPACER.
6 Tighten the flat-head screw until snug.
7 If after the flat-head screws are tightened, one or
both are protrude above the engine side surface
of the spacer, perform the following steps:
a Remove both flat-head screws and the spacer.
b Rotate the spacer 180 degrees, aligning
the screw holes in the spacer with the 8-32
threaded holes in the hub flange.
CAUTION: MAKE SURE THE FLAT-HEAD
ATTACHMENT SCREWS DO NOT
PROTRUDE ABOVE THE ENGINE-
SIDE SURFACE OF THE SPACER.
c Slide the spacer onto the mounting studs
and against the hub flange.
d Insert a flat-head screw through each
screw hole in the spacer and into the 8-32
threaded holes in the hub flange. Refer to
Figure 3-9.
e Tighten the flat-head screw until snug.
f If after the flat-head screws are tightened,
one or both are protrude above the engine
side surface of the spacer, remove the screws.
NOTE: If the propeller installation will
be delayed, the spacer and
O-ring should be installed and
temporarily held in place with non-
self locking nuts and a sufficient
number of washers on at least two
mounting studs. Remove the nuts
and washers before installation.

Page 3-25
INSTALLATION AND REMOVAL 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

CAUTION 1: MAKE SURE THAT COMPLETE AND TRUE

SURFACE CONTACT IS ESTABLISHED
BETWEEN THE SPACER AND THE
ENGINE FLANGE.
CAUTION 2: IF THE C-7364-2 SPACER IS NOT
ATTACHED TO THE HUB, MAKE SURE
THE HUB-TO-SPACER O-RING STAYS
IN THE GROOVE IN THE SPACER. IF
THE O-RING IS TWISTED OR PINCHED,
OIL LEAKAGE WILL RESULT WHEN THE
PROPELLER IS OPERATED ON THE
AIRCRAFT.
(8) Slide the propeller onto the engine flange.

OD Chamfer

Engine Flange Washer

Stud

Engine Shaft

Fillet
W10411

Installing the Washer on the Mounting Stud

Figure 3-10

Page 3-26
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

CAUTION 1: NEW PROPELLER MOUNTING NUTS

MUST BE USED WHEN INITIALLY
INSTALLING A NEW OR OVERHAULED
PROPELLER.

CAUTION 2: THE SIDE OF THE WASHER WITH THE

OD CHAMFER MUST BE AGAINST THE
ENGINE FLANGE. REFER TO FIGURE 3-10.
(9) Install self locking mounting nuts with washers onto
the propeller mounting studs. Refer to Table 3-2 for
appropriate mounting hardware. Refer to Figure 3-10.
NOTE 1: The OD chamfer on the washer is for
clearance of the engine flange fillet. Refer to
Figure 3-10.
NOTE 2: If the propeller is removed between overhaul
intervals, mounting nuts and washers may be
reused if they are not damaged or corroded.
(10)Use a torque wrench and the specified torque wrench
adaptor (see paragraph 1.A. Tooling in this chapter) to
torque all mounting nuts in the sequences and steps
shown in Figure 3-3. Refer to Table 3-3 and Figure 3-4 to
determine the proper torque value.
(11) Safety all propeller mounting studs with 0.032 inch
(0.81 mm) minimum diameter stainless steel wire or
equivalent aircraft safety cable and associated hardware
(two bolts per safety.)
(12)Decompress the external beta system and remove the
beta system puller.
CAUTION: THE BETA RING MUST NOT CONTACT ANY
ENGINE COMPONENT OR MOUNTING BOLT
SAFETY WIRE. THE BETA SYSTEM COULD
BE DAMAGED IF IT CONTACTS ANY STATIC
ENGINE COMPONENT WHILE ROTATING.
(13)Examine the beta ring to make sure that it is not in
contact with any engine components or mounting bolt
safety wire.

Page 3-27
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(a) If there is contact between the beta ring and any

engine components or mounting bolt safety wire,
consult qualified personnel at an appropriately
licensed propeller service facility.
(14)Install the carbon block into the beta linkage lever per
the airframe manufacturer’s instructions.
CAUTION 1: FIT THE BLOCK IN THE BETA RING WITH
A SIDE CLEARANCE OF 0.001 INCH
(0.03 mm). REFER TO FIGURE 3-6.

CAUTION 2: MAXIMUM SIDE CLEARANCE

PERMITTED IS 0.010 INCH (0.25 mm)
IN ACCORDANCE WITH THE CARBON
BLOCK ASSEMBLIES SECTION IN THE
MAINTENANCE PRACTICES CHAPTER
OF THIS MANUAL.
(15)Install the carbon block assembly (Figure 3-7) into the
beta ring.
(16)Install, adjust and safety the beta linkage per the
airframe manufacturer’s instructions.
CAUTION: TO FACILITATE BOXING AND SHIPPING
OF THE PROPELLER, THE PISTON NUT
MAY HAVE BEEN REMOVED TO ALLOW
ROTATING OF THE BLADES BEFORE
PACKAGING.
(17)Procedure for reinstallation of the piston nut, if
applicable.
(a) Following the installation of the propeller, use a
breaker bar and a 5/8 inch deep well socket to hold
the pitch change rod.
(b) Using a 1-7/16 inch crowfoot wrench and torque
wrench, torque the A-880-1 piston nut. Refer to
Table 3-3 and Figure 3-4 for the proper torque value.
NOTE: The removal and subsequent reinstallation
of the piston nut does not require that the
propeller blade angles be re-checked.

Page 3-28
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(18)If the propeller is equipped with an ice protection system

that uses components supplied by Hartzell Propeller
Inc., applicable instructions and technical information for
the components supplied by Hartzell Propeller Inc. can
be found in the following publications available on the
Hartzell Propeller Inc. website at www.hartzellprop.com:
(a) Manual 180 (30-61-80) - Propeller Ice Protection
System Manual
(b) Manual 181 (30-60-81) - Propeller Ice Protection
System Component Maintenance Manual
(c) Manual 182 (61-12-82) - Propeller Electrical De-ice
Boot Removal and Installation Manual
(d) Manual 183 (61-12-83) - Propeller Anti-icing Boot
Removal and Installation Manual
(19)Propeller ice protection system components not
supplied by Hartzell Propeller Inc. are controlled by the
applicable TC or STC holder’s Instructions for Continued
Airworthiness (ICA).

Page 3-29
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 W10103

SPINNER BULKHEAD
SPINNER BULKHEAD

START LOCKS

ENGINE
PROPELLER HUB FLANGE
FLANGE

START LOCKS
SPINNER MOUNTING
PLATE

INSTALLATION AND REMOVAL

SPINNER BULKHEAD
139

AND START LOCKS

ATTACHMENT BOLTS SPINNER MOUNTING
PLATE

61-00-39
SPINNER MOUNTING
PLATE “SCALLOPS”
Propeller Owner’s Manual

One-piece Spinner Mounting Plate Installation

Figure 3-11

Rev. 11 Jul/12
Page 3-30
 Propeller Owner’s Manual
139

E. Installing HC-B(3,4)( )( )-5( ) Propeller, with a One-piece

Spinner Mounting Plate, on the Aircraft Engine
CAUTION: INSTRUCTIONS AND PROCEDURES IN
THIS SECTION MAY INVOLVE CRITICAL
PARTS. REFER TO THE INTRODUCTION
CHAPTER OF THIS MANUAL FOR
INFORMATION ABOUT PROPELLER
CRITICAL PARTS. REFER TO THE
ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL
MANUAL(S) FOR THE IDENTIFICATION
OF SPECIFIC PROPELLER CRITICAL
PARTS.
NOTE: Some -5 propellers were previously manufactured
with a one-piece spinner mounting plate. The
spinner bulkhead, which has start locks mounted
on it, is attached to the spinner mounting plate.
The spinner mounting plate is installed in a
cutaway portion of the propeller hub flange and is
“pinched” between the propeller hub flange and
the engine flange. Refer to Figure 3-11.
WARNING: MAKE SURE THE SLING IS RATED UP
TO 800 LBS (363 KG) TO SUPPORT THE
WEIGHT OF THE PROPELLER ASSEMBLY
DURING INSTALLATION.

CAUTION: WHEN INSTALLING THE PROPELLER

ON THE AIRCRAFT, DO NOT DAMAGE
THE ICE PROTECTION SYSTEM
COMPONENTS, IF APPLICABLE.
(1) With a suitable crane hoist and sling, carefully move
the propeller assembly to the aircraft engine mounting
flange.
(2) Make sure the propeller hub flange and engine flange
mating surfaces are clean.
(3) Install the specified O-ring on the engine flange. Refer to
Table 3-1.

Page 3-31
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(4) Retract each start lock pin and hold into place with a
heavy wire inserted into the hole in each auto high pitch
housing.
(5) Slide the assembled one-piece spinner mounting plate,
spinner bulkhead and start lock onto the propeller hub
flange.
(a) The start locks must face toward the propeller.
(6) Align the clearance “scallops” in the spinner mounting
plate with the holes in the propeller hub flange. Refer to
Figure 3-11.
NOTE: This will insure that the spinner mounting plate
does not interfere with the mounting bolts and
dowel pins.
(7) Align the start locks with each blade and clamp mounted
stop plate.
NOTE: The start locks are attached to the spinner
bulkhead.
(8) Align mounting and dowel pin holes in the propeller hub
flange with the mounting holes and dowel pins in the
engine flange.
CAUTION: MAKE SURE THAT COMPLETE AND TRUE
SURFACE CONTACT IS ESTABLISHED
BETWEEN THE PROPELLER HUB
FLANGE AND THE ENGINE FLANGE.
(9) Slide the propeller flange onto the engine flange.
CAUTION: NEW PROPELLER MOUNTING BOLTS
MUST BE USED WHEN INITIALLY
INSTALLING A NEW OR OVERHAULED
PROPELLER.
(10)Apply MIL-PRF-83483 anti-seize compound to the
threaded surfaces of the mounting bolts. Refer to Table
3-2 for appropriate mounting hardware.
NOTE: If the propeller is removed between overhaul
intervals, mounting bolts and washers may be
reused if they are not damaged or corroded.

Page 3-32
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

CAUTION: ID CHAMFER OF THE WASHER MUST

BE FACING TOWARD THE BOLT HEAD.
WASHERS WITHOUT CHAMFER MUST
BE INSTALLED WITH ROLLED EDGES
TOWARD THE BOLT HEAD (FIGURE 3-1).
(11) Install the mounting bolts with washers through the
engine flange and into the propeller hub flange. Refer to
Figure 3-2.
(12)Use a torque wrench and the specified torque wrench
adaptor (see paragraph 1.A. Tooling in this chapter)
to torque all mounting bolts in sequences and steps
shown in Figure 3-3. Refer to Table 3-3 and Figure 3-4 to
determine the proper torque value.
(13)Safety all mounting bolts with 0.032 inch (0.81 mm)
minimum diameter stainless steel wire or equivalent
aircraft safety cable and associated hardware (two bolts
per safety.)
(14)Remove the heavy wire from the start lock housings to
free the start lock pins.
(15)Refer to the airframe manufacturer’s instructions to seat
the start lock plates on the start locks.
NOTE: The start lock plates interface with the start
lock pins and are attached to the inboard
surface of each blade clamp.
CAUTION: TO FACILITATE BOXING AND SHIPPING
OF PROPELLERS, THE PISTON NUT
(A-880-2) ON -5 STEEL HUB TURBINE
PROPELLERS MAY HAVE BEEN
REMOVED TO ALLOW ROTATING OF THE
BLADES BEFORE PACKAGING.
(16)Procedure for reinstallation of piston nut, if applicable.
(a) Following the installation of the propeller, use a
breaker bar and a one inch deep well socket to hold
the pitch change rod.

Page 3-33
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(b) Using a 1-13/16 inch crowfoot wrench and torque

wrench, torque the A-880-2 piston nut. Refer to
Table 3-3 and Figure 3-4 for the proper torque value.
NOTE: The removal and subsequent reinstallation
of the piston nut does not require that the
propeller blade angles be re-checked.
(17)Install the beta tube per airframe and/or engine
manufacturer’s instructions.
NOTE 1: Follow the airframe manufacturer’s instructions
for adjusting the beta tube to obtain the correct
low pitch (flight idle blade angle).
NOTE 2: Refer to the Aircraft Type Certificate Data
Sheet for the low pitch blade angle setting.
(18)If the propeller is equipped with an ice protection system
that uses components supplied by Hartzell Propeller
Inc., applicable instructions and technical information for
the components supplied by Hartzell Propeller Inc. can
be found in the following publications available on the
Hartzell Propeller Inc. website at www.hartzellprop.com:
(a) Manual 180 (30-61-80) - Propeller Ice Protection
System Manual
(b) Manual 181 (30-60-81) - Propeller Ice Protection
System Component Maintenance Manual
(c) Manual 182 (61-12-82) - Propeller Electrical De-ice
Boot Removal and Installation Manual
(d) Manual 183 (61-12-83) - Propeller Anti-icing Boot
Removal and Installation Manual
(19)Propeller ice protection system components not
supplied by Hartzell Propeller Inc. are controlled by the
applicable TC or STC holder’s Instructions for Continued
Airworthiness (ICA).

Page 3-34
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

F. Installing HC-B(3,4,5)( )( )-5( ) Propeller, with a Two-piece

Spinner Mounting Plate, on the Aircraft Engine
CAUTION: INSTRUCTIONS AND PROCEDURES IN
THIS SECTION MAY INVOLVE CRITICAL
PARTS. REFER TO THE INTRODUCTION
CHAPTER OF THIS MANUAL FOR
INFORMATION ABOUT PROPELLER
CRITICAL PARTS. REFER TO THE
ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL
MANUAL(S) FOR THE IDENTIFICATION
OF SPECIFIC PROPELLER CRITICAL
PARTS.
NOTE: Some -5 propellers are manufactured with a
two-piece spinner mounting plate which is bolted
on the propeller hub flange. On four and five-blade
propellers (see Figure 2-7) the bulkhead and start
locks are attached to the spinner mounting plate.
On three-bladed propellers (see Figure 2-6) the
start locks are attached to the guide collar (between
the hub and cylinder); although the bulkhead is
attached to the spinner mounting plate.
WARNING: MAKE SURE THE SLING IS RATED UP
TO 800 LBS (363 KG) TO SUPPORT THE
WEIGHT OF THE PROPELLER ASSEMBLY
DURING INSTALLATION.

CAUTION: WHEN INSTALLING THE PROPELLER

ON THE AIRCRAFT, DO NOT DAMAGE
THE ICE PROTECTION SYSTEM
COMPONENTS, IF APPLICABLE.
(1) With a suitable crane hoist and sling, carefully move
the propeller assembly to the aircraft engine mounting
flange.
(a) If the propeller is equipped with a de-ice system,
refer to the General Maintenance Practices section
in the Introduction chapter of this manual.

Page 3-35
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(2) Make sure the propeller hub flange and engine flange
mating surfaces are clean.
(3) Install the specified O-ring on the engine flange. Refer to
Table 3-1.
(4) Align the mounting and dowel pin holes in the propeller
hub flange with the mounting holes and dowel pins in the
engine flange.
CAUTION: MAKE SURE THAT COMPLETE AND TRUE
SURFACE CONTACT IS ESTABLISHED
BETWEEN THE PROPELLER HUB
FLANGE AND THE ENGINE FLANGE.
(5) Slide the propeller flange onto the engine flange.
CAUTION: NEW PROPELLER MOUNTING BOLTS
MUST BE USED WHEN INITIALLY
INSTALLING A NEW OR OVERHAULED
PROPELLER.
(6) Apply MIL-PRF-83483 anti-seize compound to the
threaded surfaces of the mounting bolts. Refer to
Table 3-2 for appropriate mounting hardware.
NOTE: If the propeller is removed between overhaul
intervals, mounting bolts and washers may be
reused if they are not damaged or corroded.
CAUTION: ID CHAMFER OF THE WASHER MUST
BE FACING TOWARD THE BOLT HEAD.
WASHERS WITHOUT CHAMFER MUST
BE INSTALLED WITH ROLLED EDGES
TOWARD THE BOLT HEAD (FIGURE 3-1).
(7) Install the mounting bolts with washers through the
engine flange and into the propeller hub flange. Refer to
Figure 3-2.
(8) Use a torque wrench and the specified torque wrench
adaptor (see paragraph 1.A. Tooling) to torque all
mounting bolts in sequences and steps shown in
Figure 3-3. Refer to Table 3-3 and Figure 3-4 to
determine the proper torque value.

Page 3-36
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(9) Safety all mounting bolts with 0.032 inch (0.81 mm)
minimum diameter stainless steel wire or equivalent
aircraft safety cable and associated hardware (two bolts
per safety.)
CAUTION: TO FACILITATE BOXING AND SHIPPING
OF PROPELLERS, THE PISTON NUT
(A-880-2) ON -5 STEEL HUB TURBINE
PROPELLERS MAY HAVE BEEN
REMOVED TO ALLOW ROTATING OF THE
BLADES BEFORE PACKAGING.
(10)Procedure for reinstallation of piston nut, if applicable.
(a) Following the installation of the propeller, use a
breaker bar and a one inch deep well socket to hold
the pitch change rod.
(b) Using a 1-13/16 inch crowfoot wrench and torque
wrench, torque the A-880-2 piston nut. Refer to
Table 3-3 and Figure 3-4 for the proper torque value.
NOTE: The removal and subsequent reinstallation
of the piston nut does not require that the
propeller blade angles be re-checked.
(11) Install the beta tube per airframe and/or engine
manufacturer’s instructions.
(a) Follow the airframe manufacturer’s instructions for
adjusting the beta tube to obtain the correct low pitch
(flight idle blade angle).
(b) Refer to the Aircraft Type Certificate Data Sheet for
the low pitch blade angle setting.
(12)If the propeller is equipped with an ice protection system
that uses components supplied by Hartzell Propeller
Inc., applicable instructions and technical information for
the components supplied by Hartzell Propeller Inc. can
be found in the following publications available on the
Hartzell Propeller Inc. website at www.hartzellprop.com:
(a) Manual 180 (30-61-80) - Propeller Ice Protection
System Manual
(b) Manual 181 (30-60-81) - Propeller Ice Protection
System Component Maintenance Manual

Page 3-37
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 W10101 ROD END PIN
COVER FITTING
PLATE
ROD END
CAP

CHECK NUT

PUSH ROD
SPOOL
ENGINE SHAFT
ADAPTOR
SPRING

SLEEVE

ROD

INSTALLATION AND REMOVAL

O-RINGS (SUPPLIED
SELF LOCKING BY THE ENGINE
MANUFACTURER)
139

NUT

SPRING

61-00-39
RETAINER

PITCH
Propeller Owner’s Manual

SPACER CHANGE ROD

Beta Valve System

Rev. 13 Jun/15
Page 3-38
Figure 3-12
 W10102A

O-RINGS (SUPPLIED BY
ENGINE SHAFT THE ENGINE
ADAPTOR MANUFACTURER)

ROD END
CAP

CHECK NUT
C-3317-116
COVER SPRING O-RINGS
PLATE RETAINER

C-3317-111
O-RING

INSTALLATION AND REMOVAL

139

BETA VALVE
SLEEVE

61-00-39
ROD END OUTER
SPRING ROD
FITTING
PUSH ROD
Propeller Owner’s Manual

C-3317-006 INNER
SPOOL
O-RING SPRING

Cross Section View of the Beta Valve System

Rev. 13 Jun/15
Page 3-39
Figure 3-13
 Propeller Owner’s Manual
139

(c) Manual 182 (61-12-82) - Propeller Electrical De-ice

Boot Removal and Installation Manual
(d) Manual 183 (61-12-83) - Propeller Anti-icing Boot
Removal and Installation Manual
(13)Propeller ice protection system components not
supplied by Hartzell Propeller Inc. are controlled by the
applicable TC or STC holder’s Instructions for Continued
Airworthiness (ICA).
G. Installing HC-( )3( )( )-7( ) Propeller on the Allison Engine
CAUTION: INSTRUCTIONS AND PROCEDURES IN
THIS SECTION MAY INVOLVE CRITICAL
PARTS. REFER TO THE INTRODUCTION
CHAPTER OF THIS MANUAL FOR
INFORMATION ABOUT PROPELLER
CRITICAL PARTS. REFER TO THE
ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL
MANUAL(S) FOR THE IDENTIFICATION
OF SPECIFIC PROPELLER CRITICAL
PARTS.
This propeller incorporates a beta valve assembly
(Figures 3-12 and 3-13), which is installed inside of the
propeller shaft and extends from the rear of the engine to the
front of the propeller piston. This assembly is installed in the
engine shaft before the propeller is installed.
(1) Make sure that the shaft adaptor (see Figure 3-13) is
installed in the engine shaft.
(2) Install the C-3317-116 O-rings in the two grooves
(see Figure 3-13) of the shaft adaptor.
(3) Remove the cover plate from the rear of engine case.
Refer to Figures 3-12 and 3-13.
(4) Prepare the beta valve.
NOTE: The beta valve should be preassembled as
shown in Figure 3-12 less the pitch change
rod, engine shaft adaptor, engine supplied
o-rings and cover plate when new or from
overhaul.

Page 3-40
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

Refer to Figures 3-12 and 3-13.

(a) If the beta valve is supplied preassembled, remove
the self locking nut, spacer, rod end cap, rod end
fitting, bushing and check nut.
(b) If the beta valve is supplied disassembled, assemble
as follows:
1 Slide the push rod spool onto the pin and into
the sleeve with the threaded end facing away
from the sleeve.
2 Slide the inner and outer springs onto the rod up
to and against the shoulder of the sleeve.
3 Install the spring retainer onto the rod with the
recessed center section facing toward the two
springs.
(5) Slide the partially assembled beta valve into the engine
shaft from the front, allowing the push rod spool to
extend out the rear of the engine.
(a) The shoulder of the sleeve should be against the
shaft adaptor.
(6) Compress the springs with spring retainer and install the
retaining ring that is furnished with the engine to secure
the spring retainer.
NOTE: A locator button on the spring retainer will fit
into a recess in the engine shaft/flange.
(7) Install the ID and OD O-rings on the engine cover, per
the airframe or engine manufacturer’s instructions.
(8) Install the engine cover on the rear of the engine
gear box encircling the beta valve push rod spool, per
airframe or engine manufacturer’s instructions.
NOTE: Cover plate fasteners are supplied by the
engine manufacturer.

Page 3-41
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 W10082
SEE FIGURE 3-15

HUB
GUIDE COLLAR

MOUNTING WASHER CYLINDER SPRING

ASSEMBLY

MOUNTING BOLT

ENGINE FLANGE PISTON NUT

C-3317-012-2
PISTON GUIDE ROD O-RING
SPACER

INSTALLATION AND REMOVAL

SELF LOCKING
WASHER NUT
JAM NUT
139

BETA VALVE
SOCKET HEAD CAP SCREW
LINK PIN UNIT PITCH CHANGE
(SEE FIGURE 3-16)

61-00-39
SPINNER BULKHEAD ROD
PISTON
LINK PIN SCREW
BLADE CLAMP (SEE FIGURE 3-16)
Propeller Owner’s Manual

LINK ARM

-7( ) Propeller Assembly

Rev. 13 Jun/15
Page 3-42
Figure 3-14
 Propeller Owner’s Manual
139

W10139
W10136 SPRING
RETAINER

RING RETENTION
PLATE

SPLIT
RETAINER

RING RETENTION
PLATE SCREW

CYLINDER

Spring Assembly to Cylinder Attachment Details

Figure 3-15

W10137

PISTON SLOT
PISTON

LINK PIN UNIT

SAFETY WIRE

SAFETY SCREW

LINK ARM

Piston to Link Arm Attachment Details

Figure 3-16

Page 3-43
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(9) Prepare the propeller for installation (see Figures 3-14

through 3-16 ).
(a) Piston removal
1 Remove the flexlock nut with a 1-7/16 inch
wrench, if installed.
2 Remove the safety wire from the three link pin
units.
3 Remove the safety screws from the link pin
units.
4 Remove the link pin units.
5 Mark the piston and link pins with a felt tip pen
or equivalent, so the piston can be reinstalled in
the same position.
6 Slide the link arms out of the piston slots.
7 Remove the socket head cap screw, jam nut,
and washer from each piston guide rod.
8 Slide the piston off the cylinder.
(b) Spring assembly removal.
1 Remove the ring retention plate screw safety
wire.
2 Remove the ring retention plate screws.
3 Remove the retention plate.
4 Remove the split retainer.
5 Remove the spring assembly from the cylinder.

Page 3-44
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

WARNING: MAKE SURE THE SLING IS RATED UP

TO 800 LBS (363 KG) TO SUPPORT THE
WEIGHT OF THE PROPELLER ASSEMBLY
DURING REMOVAL.

CAUTION: INSERT THE DOWEL PINS INTO

THE PROPELLER FLANGE USING A
BRASS HAMMER OR EQUIVALENT
TOOL TO PREVENT DAMAGE TO THE
DOWEL PINS. THE DOWEL PINS ARE
AN INTERFERENCE FIT WITH THE
PROPELLER FLANGE.
(10)Insert two dowel pins (Table 3-1) through the threadless
holes in the propeller flange, flush with the propeller
side of the hub flange. The dowel pins will protrude from
the engine side of the hub flange to engage the engine
flange.
(11) With a suitable crane hoist and sling, carefully move
the propeller assembly to the aircraft engine mounting
flange.
NOTE: If the propeller is equipped with a de-ice
system, refer to the General Maintenance
Practices section in the Introduction chapter of
this manual.
(12)Make sure the propeller hub flange and engine flange
mating surfaces are clean.
(13)Install the specified O-ring on the engine flange. Refer to
Table 3-1.
CAUTION: DO NOT ALLOW THE PROPELLER
ASSEMBLY TO HIT OR REST ON THE
BETA FEEDBACK ROD. THIS COULD
BEND OR OTHERWISE DAMAGE THE
FEEDBACK ROD.
(14)Slide the propeller over the beta valve assembly.
(15)Align the mounting holes and dowel pins in the propeller
hub flange with the mounting holes and dowel pin holes
in the engine flange.

Page 3-45
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

CAUTION: MAKE SURE THAT COMPLETE AND TRUE

SURFACE CONTACT IS ESTABLISHED
BETWEEN THE PROPELLER HUB
FLANGE AND THE ENGINE FLANGE.
(16)Slide the propeller hub flange onto the engine flange.
CAUTION 1: ID CHAMFER OF THE WASHER MUST
BE FACING TOWARD THE BOLT HEAD.
WASHERS WITHOUT CHAMFER MUST
BE INSTALLED WITH ROLLED EDGES
TOWARD THE BOLT HEAD (FIGURE 3-1).

CAUTION 2: NEW PROPELLER MOUNTING BOLTS

MUST BE USED WHEN INITIALLY
INSTALLING A NEW OR OVERHAULED
PROPELLER.
(17)Install the propeller mounting bolts and washers through
the engine flange and into the propeller hub flange.
Refer to Table 3-2 for appropriate mounting hardware.
NOTE: If the propeller is removed between overhaul
intervals, mounting bolts and washers may be
reused if they are not damaged or corroded.
(18)Use a torque wrench and the specified torque wrench
adaptor (see paragraph 1.A. Tooling in this chapter)
to torque all mounting bolts in sequences and steps
shown in Figure 3-3. Refer to Table 3-3 and Figure 3-4 to
determine the proper torque value.
(19)Safety all mounting bolts with 0.032 inch (0.81 mm)
minimum diameter stainless steel wire or equivalent
aircraft safety cable and associated hardware (two bolts
per safety.)
(20)Reinstall the spring assembly (see Figures 3-14 and
3-15).
(a) Slide the spring assembly into the cylinder and
around the beta valve rod.
(b) Install split retainer between the cylinder and front
spring retainer. Slide retainer into the recess in the
cylinder.

Page 3-46
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(c) Pull the spring retainer tight against the split retainer.
(d) Install the ring retention plate.
(e) Install the ring retention plate screws and tighten
until snug.
(f) Safety screws with 0.032 inch (0.81 mm) minimum
diameter stainless steel safety wire or equivalent
aircraft safety cable and associated hardware (two
bolts per safety.)
(21)Install the C-3317-012-2 O-ring in the front inside cavity
of the pitch change rod. (See Figure 3-14.)
(22)Reinstall the piston on the cylinder and pitch change rod
in the same position it was before disassembly. Refer to
Figures 3-14 and 3-16.
(a) Reconnect the link arms to the piston.
(b) Install the link pin units.
(c) Install the link pin unit safety screws.
(d) Safety the link pin screws with 0.032 inch (0.81 mm)
minimum diameter stainless steel safety wire (see
Figure 3-16).
(e) Hand tighten the A-880-1 piston nut on the pitch
change rod.
(f) Position a breaker bar and a 5/8 inch deep well
socket on the pitch change rod.
(g) Use 1-7/16 inch crowfoot wrench and torque wrench
to torque the A-880-1 piston nut. Refer to Table 3-3
and Figure 3-4 for the proper torque value.
NOTE: The removal and subsequent reinstallation
of the piston nut does not require that the
propeller blade angles be re-checked.
(h) Install a socket head screw, washer and jam nut
onto each piston guide rod. Refer to Figure 3-14.
(i) Torque the jam nuts on the piston guide rods as
indicated in Table 3-3.

Page 3-47
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

CAUTION: THE ROD END CAP MUST BOTTOM

ON THE PUSH ROD SPOOL WHEN
INSTALLED.
(23)Install the rod end cap onto the threaded end of the push
rod spool.
NOTE: Do not tighten the set screw in the rod end
cap.
(a) Mark the location of the set screw on the rod and
then remove the end cap unit.
(b) File a flat, tangent to the rod, no deeper than the
depth of the threads at the marked location of the
set screw. Refer to Figure 3-17.
(24)Install the check nut onto the threaded end of the push
rod spool.
(25)Install the bushing onto the threaded end of the push rod
spool.
(26)Install the rod end fitting onto the threaded end of the
push rod spool.
(27)Install the C-3317-006 O-ring in the cavity at the rear
end of the push rod spool.

W10138

FILED FLAT

PUSH ROD SPOOL

Filed Rod for Set Screw

Figure 3-17

Page 3-48
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(28)Install the rod end cap onto the threaded end of the push
rod spool.
NOTE: Make sure the rod end cap is bottomed on the
end of the push rod spool.
(a) Apply Loctite® 272 to the set screw threads.
(b) Tighten the set screw.
(29)Apply Loctite® 272 to the push rod threads where the
check nut will be located on the push rod spool next to
the bushing.
(30)Tighten the check nut against the bushing to torque
indicated in Table 3-3.
(31)Attach engine mounted beta system control hardware
to rod end fitting and adjust per airframe or engine
manufacturer’s instructions.
(32)Install the beta light switch against the pin per airframe
manufacturer’s instructions.
(33)Install the spacer and self-locking nut onto the front
of the rod that protrudes through the front of the pitch
change rod and piston.
(a) Follow the airframe manufacturer’s instructions for
making pitch control adjustments.
(34)If the propeller is equipped with an ice protection system
that uses components supplied by Hartzell Propeller
Inc., applicable instructions and technical information for
the components supplied by Hartzell Propeller Inc. can
be found in the following publications available on the
Hartzell Propeller Inc. website at www.hartzellprop.com:
(a) Manual 180 (30-61-80) - Propeller Ice Protection
System Manual
(b) Manual 181 (30-60-81) - Propeller Ice Protection
System Component Maintenance Manual
(c) Manual 182 (61-12-82) - Propeller Electrical De-ice
Boot Removal and Installation Manual
(d) Manual 183 (61-12-83) - Propeller Anti-icing Boot
Removal and Installation Manual

Page 3-49
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(35)Propeller ice protection system components not

supplied by Hartzell Propeller Inc. are controlled by the
applicable TC or STC holder’s Instructions for Continued
Airworthiness (ICA).
4. Spinner Dome Installation
CAUTION 1: INSTRUCTIONS AND PROCEDURES IN THIS
SECTION MAY INVOLVE CRITICAL PARTS.
REFER TO THE INTRODUCTION CHAPTER
OF THIS MANUAL FOR INFORMATION ABOUT
PROPELLER CRITICAL PARTS. REFER TO
THE ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL MANUAL(S)
FOR THE IDENTIFICATION OF SPECIFIC
PROPELLER CRITICAL PARTS.

CAUTION 2: TO PREVENT DAMAGE TO THE BLADE AND

BLADE PAINT, WRAP THE BLADE SHANKS IN
SEVERAL LAYERS OF MASKING OR DUCT
TAPE BEFORE INSTALLING THE SPINNER
DOME. REMOVE THE TAPE AFTER THE
SPINNER IS INSTALLED.

CAUTION 3: SPINNER DOME WILL WOBBLE IF NOT

ALIGNED PROPERLY, AND MAY AFFECT
DYNAMIC BALANCE OF PROPELLER.
A. Carefully slide the spinner dome over the reassembled
propeller.
B. Secure the spinner dome to the spinner bulkhead with the
supplied screws and washers.
5. Post-Installation Checks
A. Refer to the airframe manufacturer’s instructions for
post-installation checks.
B. Perform a maximum RPM (Static) hydraulic low pitch stop
check in accordance with the Testing and Troubleshooting
chapter of this manual.

Page 3-50
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

6. Spinner Dome Removal

CAUTION 1: INSTRUCTIONS AND PROCEDURES IN THIS
SECTION MAY INVOLVE CRITICAL PARTS.
REFER TO THE INTRODUCTION CHAPTER
OF THIS MANUAL FOR INFORMATION ABOUT
PROPELLER CRITICAL PARTS. REFER TO
THE ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL MANUAL(S)
FOR THE IDENTIFICATION OF SPECIFIC
PROPELLER CRITICAL PARTS.

CAUTION 2: TO PREVENT DAMAGING THE BLADE AND

BLADE PAINT, WRAP THE BLADE SHANKS IN
SEVERAL LAYERS OF MASKING OR DUCT
TAPE BEFORE REMOVING THE SPINNER
DOME.
A. Remove the screws and washers that secure the spinner to
the spinner bulkhead.
B. Remove the spinner dome.

Page 3-51
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

7. Propeller Assembly Removal

A. Removal of HC-B(3,5)( )( )-2( ) Propellers
WARNING: FOR SAFETY REASONS, THE
PROPELLER MUST BE PUT IN FEATHER
POSITION BEFORE IT IS REMOVED
FROM THE AIRCRAFT.

CAUTION: INSTRUCTIONS AND PROCEDURES IN

THIS SECTION MAY INVOLVE CRITICAL
PARTS. REFER TO THE INTRODUCTION
CHAPTER OF THIS MANUAL FOR
INFORMATION ABOUT PROPELLER
CRITICAL PARTS. REFER TO THE
ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL
MANUAL(S) FOR THE IDENTIFICATION
OF SPECIFIC PROPELLER CRITICAL
PARTS.
(1) Remove the spinner dome in accordance with the
procedure in the Spinner Dome Removal section of this
chapter.
(a) If the propeller is equipped with an ice protection
system that uses components supplied by Hartzell
Propeller Inc., applicable instructions and technical
information for the components supplied by
Hartzell Propeller Inc. can be found in the following
publications available on the Hartzell Propeller Inc.
website at www.hartzellprop.com:
1 Manual 180 (30-61-80) - Propeller Ice Protection
System Manual
2 Manual 181 (30-60-81) - Propeller Ice Protection
System Component Maintenance Manual
3 Manual 182 (61-12-82) - Propeller Electrical
De-ice Boot Removal and Installation Manual
4 Manual 183 (61-12-83) - Propeller Anti-icing
Boot Removal and Installation Manual

Page 3-52
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(b) Propeller ice protection system components not

supplied by Hartzell Propeller Inc. are controlled by
the applicable TC or STC holder’s Instructions for
Continued Airworthiness (ICA).
WARNING 1: DURING ENGINE INSTALLATION OR
REMOVAL, USING THE PROPELLER TO
SUPPORT THE WEIGHT OF THE ENGINE
IS NOT AUTHORIZED. UNAPPROVED
INSTALLATION AND REMOVAL
TECHNIQUES MAY CAUSE DAMAGE TO
THE PROPELLER THAT MAY LEAD TO
FAILURE AND RESULT IN AN AIRCRAFT
ACCIDENT.

WARNING 2: DURING PROPELLER REMOVAL,

AIRFRAME MANUFACTURER’S
MANUALS AND PROCEDURES MUST
BE FOLLOWED BECAUSE THEY MAY
CONTAIN ISSUES VITAL TO AIRCRAFT
SAFETY THAT ARE NOT CONTAINED
IN THIS MANUAL OR THE HARTZELL
PROPELLER INC. OVERHAUL MANUALS
118F (61-10-18) AND 132A (61-10-32).

WARNING 3: MAKE SURE THE SLING IS RATED UP

TO 800 LBS (363 KG) TO SUPPORT THE
WEIGHT OF THE PROPELLER ASSEMBLY
DURING REMOVAL.
(2) Cut and remove the safety wire on the propeller
mounting bolts.

Page 3-53
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(3) Support the propeller assembly with a sling.

NOTE 1: Supporting the propeller with the sling may be
delayed until all but two mounting bolts and
washers have been removed to allow rotating
the propeller for ease of bolt removal.
NOTE 2: If the propeller will be reinstalled, and it
has been dynamically balanced, make an
identifying mark on the propeller hub and a
matching mark on the engine flange to ensure
proper orientation during re-installation to
prevent dynamic imbalance.
CAUTION: DISCARD THE PROPELLER MOUNTING
BOLTS IF THEY ARE DAMAGED OR
CORRODED, OR WHEN THE PROPELLER
IS REMOVED FOR OVERHAUL.
(4) Remove the propeller mounting bolts and washers.
NOTE: If the propeller is removed between overhaul
intervals, mounting bolts and washers may be
reused if they are not damaged or corroded.
CAUTION: USE ADEQUATE PRECAUTIONS TO
PROTECT THE PROPELLER ASSEMBLY
FROM DAMAGE WHEN IT IS REMOVED
FROM THE AIRCRAFT ENGINE AND
WHEN IT IS STORED.
(5) Using the support sling, lift the propeller from the
mounting flange.
(6) Remove and discard the propeller mounting O-ring.
(7) Place the propeller on a suitable cart for transportation.

Page 3-54
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

B. Removal of HC-B(3,4,5)( )(A,N,P)-3( ) Propellers

WARNING: FOR SAFETY REASONS, THE
PROPELLER MUST BE PUT IN FEATHER
POSITION BEFORE IT IS REMOVED
FROM THE AIRCRAFT, IF THE BLADES
ARE AT A STARTING BLADE ANGLE DUE
TO START LOCKS.

CAUTION: INSTRUCTIONS AND PROCEDURES IN

THIS SECTION MAY INVOLVE CRITICAL
PARTS. REFER TO THE INTRODUCTION
CHAPTER OF THIS MANUAL FOR
INFORMATION ABOUT PROPELLER
CRITICAL PARTS. REFER TO THE
ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL
MANUAL(S) FOR THE IDENTIFICATION
OF SPECIFIC PROPELLER CRITICAL
PARTS.
(1) Remove the spinner dome in accordance with the
procedure in the Spinner Dome Removal section of this
chapter.
(a) If the propeller is equipped with an ice protection
system that uses components supplied by Hartzell
Propeller Inc., applicable instructions and technical
information for the components supplied by
Hartzell Propeller Inc. can be found in the following
publications available on the Hartzell Propeller Inc.
website at www.hartzellprop.com:
1 Manual 180 (30-61-80) - Propeller Ice Protection
System Manual
2 Manual 181 (30-60-81) - Propeller Ice Protection
System Component Maintenance Manual
3 Manual 182 (61-12-82) - Propeller Electrical
De-ice Boot Removal and Installation Manual
4 Manual 183 (61-12-83) - Propeller Anti-icing
Boot Removal and Installation Manual

Page 3-55
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(b) Propeller ice protection system components not

supplied by Hartzell Propeller Inc. are controlled by
the applicable TC or STC holder’s Instructions for
Continued Airworthiness (ICA).
(2) Disconnect the engine beta linkage and carbon
block assembly from the beta ring per the airframe
manufacturer’s instructions. Refer to Figure 3-7.
(a) If the carbon block must be removed, perform the
following procedures:
1 Remove the snap ring that retains the carbon
block assembly to the beta linkage.
2 Remove the carbon block assembly.
CAUTION: MAKE SURE THAT THE BETA
LINKAGE IS DISCONNECTED BEFORE
COMPRESSING THE BETA SYSTEM.
(3) Use the beta system puller, Hartzell Propeller Inc.
P/N CST-2987, to compress the beta system and pull
the beta ring forward to expose the propeller mounting
bolts and washers. Refer to Figure 3-5.

Page 3-56
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

WARNING 1: DURING ENGINE INSTALLATION OR

REMOVAL, USING THE PROPELLER TO
SUPPORT THE WEIGHT OF THE ENGINE
IS NOT AUTHORIZED. UNAPPROVED
INSTALLATION AND REMOVAL
TECHNIQUES MAY CAUSE DAMAGE TO
THE PROPELLER THAT MAY LEAD TO
FAILURE AND RESULT IN AN AIRCRAFT
ACCIDENT.

WARNING 2: DURING PROPELLER REMOVAL,

AIRFRAME MANUFACTURER’S
MANUALS AND PROCEDURES MUST
BE FOLLOWED BECAUSE THEY MAY
CONTAIN ISSUES VITAL TO AIRCRAFT
SAFETY THAT ARE NOT CONTAINED
IN THIS MANUAL OR THE HARTZELL
PROPELLER INC. OVERHAUL MANUALS
118F (61-10-18) AND 132A (61-10-32).

WARNING 3: MAKE SURE THE SLING IS RATED UP

TO 800 LBS (363 KG) TO SUPPORT THE
WEIGHT OF THE PROPELLER ASSEMBLY
DURING REMOVAL.
(4) Cut and remove the safety wire on the propeller
mounting bolts.
(5) Support the propeller assembly with a sling.
NOTE 1: Supporting the propeller with the sling may be
delayed until all but two mounting bolts and
washers have been removed to allow rotating
the propeller for ease of bolt removal.
NOTE 2: If the propeller will be reinstalled, and it
has been dynamically balanced, make an
identifying mark on the propeller hub and a
matching mark on the engine flange to ensure
proper orientation during re-installation to
prevent dynamic imbalance.

Page 3-57
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

CAUTION: DISCARD THE PROPELLER MOUNTING

BOLTS IF THEY ARE DAMAGED OR
CORRODED, OR WHEN THE PROPELLER
IS REMOVED FOR OVERHAUL.
(6) Remove the propeller mounting bolts and washers.
NOTE: If the propeller is removed between overhaul
intervals, mounting bolts and washers may be
reused if they are not damaged or corroded.
CAUTION: USE ADEQUATE PRECAUTIONS TO
PROTECT THE PROPELLER ASSEMBLY
FROM DAMAGE WHEN IT IS REMOVED
FROM THE AIRCRAFT ENGINE AND
WHEN IT IS STORED.
(7) Using the support sling, lift the propeller from the
mounting flange.
(8) Remove and discard the propeller mounting O-ring.
(9) Decompress and remove the beta system puller.
(10)Place the propeller on a suitable cart for transportation.

Page 3-58
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

C. Removal of HC-B(3,4)( )W-3( ) Propellers

CAUTION: INSTRUCTIONS AND PROCEDURES IN
THIS SECTION MAY INVOLVE CRITICAL
PARTS. REFER TO THE INTRODUCTION
CHAPTER OF THIS MANUAL FOR
INFORMATION ABOUT PROPELLER
CRITICAL PARTS. REFER TO THE
ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL
MANUAL(S) FOR THE IDENTIFICATION
OF SPECIFIC PROPELLER CRITICAL
PARTS.
(1) Remove the spinner dome in accordance with the
procedure in the Spinner Dome Removal section of this
chapter.
(a) If the propeller is equipped with an ice protection
system that uses components supplied by Hartzell
Propeller Inc., applicable instructions and technical
information for the components supplied by
Hartzell Propeller Inc. can be found in the following
publications available on the Hartzell Propeller Inc.
website at www.hartzellprop.com:
1 Manual 180 (30-61-80) - Propeller Ice Protection
System Manual
2 Manual 181 (30-60-81) - Propeller Ice Protection
System Component Maintenance Manual
3 Manual 182 (61-12-82) - Propeller Electrical
De-ice Boot Removal and Installation Manual
4 Manual 183 (61-12-83) - Propeller Anti-icing
Boot Removal and Installation Manual
(b) Propeller ice protection system components not
supplied by Hartzell Propeller Inc. are controlled by
the applicable TC or STC holder’s Instructions for
Continued Airworthiness (ICA).
(2) Disconnect the engine beta linkage and carbon
block assembly from the beta ring per the airframe
manufacturer’s instructions. Refer to Figure 3-7.

Page 3-59
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(a) If the carbon block must be removed, perform the

following procedures:
1 Remove the snap ring that retains the carbon
block assembly to the beta linkage.
2 Remove the carbon block assembly.
CAUTION: MAKE SURE THAT THE BETA
LINKAGE IS DISCONNECTED BEFORE
COMPRESSING THE BETA SYSTEM.
(3) Use the beta system puller, Hartzell Propeller Inc.
P/N CST-2987, to compress the beta system and pull
the beta ring forward to expose the propeller mounting
nuts and washers. Refer to Figure 3-5.
WARNING 1: DURING ENGINE INSTALLATION OR
REMOVAL, USING THE PROPELLER TO
SUPPORT THE WEIGHT OF THE ENGINE
IS NOT AUTHORIZED. UNAPPROVED
INSTALLATION AND REMOVAL
TECHNIQUES MAY CAUSE DAMAGE TO
THE PROPELLER THAT MAY LEAD TO
FAILURE AND RESULT IN AN AIRCRAFT
ACCIDENT.

WARNING 2: DURING PROPELLER REMOVAL,

AIRFRAME MANUFACTURER’S
MANUALS AND PROCEDURES MUST
BE FOLLOWED BECAUSE THEY MAY
CONTAIN ISSUES VITAL TO AIRCRAFT
SAFETY THAT ARE NOT CONTAINED
IN THIS MANUAL OR THE HARTZELL
PROPELLER INC. OVERHAUL MANUALS
118F (61-10-18) AND 132A (61-10-32).

WARNING 3: MAKE SURE THE SLING IS RATED UP

TO 800 LBS (363 KG) TO SUPPORT THE
WEIGHT OF THE PROPELLER ASSEMBLY
DURING REMOVAL.
(4) Cut and remove the safety wire on the propeller
mounting studs.

Page 3-60
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(5) Support the propeller assembly with a sling.

NOTE 1: Supporting the propeller with the sling may be
delayed until all but two mounting nuts and
washers have been removed to allow rotating
the propeller for ease of nut removal.
NOTE 2: If the propeller will be reinstalled, and it
has been dynamically balanced, make an
identifying mark on the propeller hub and a
matching mark on the engine flange to ensure
proper orientation during re-installation to
prevent dynamic imbalance.
CAUTION: DISCARD THE PROPELLER MOUNTING
NUTS AND/OR WASHERS IF THEY ARE
DAMAGED OR CORRODED, OR WHEN
THE PROPELLER IS REMOVED FOR
OVERHAUL.
(6) Remove the propeller mounting nuts and washers.
NOTE: If the propeller is removed between overhaul
intervals, mounting nuts and washers may be
reused if they are not damaged or corroded.
CAUTION: USE ADEQUATE PRECAUTIONS TO
PROTECT THE PROPELLER ASSEMBLY
FROM DAMAGE WHEN IT IS REMOVED
FROM THE AIRCRAFT ENGINE AND
WHEN IT IS STORED.
(7) Using the support sling, lift the propeller from the
mounting flange.
(8) Remove and discard the engine flange-to-spacer O-ring.
(9) If the C-7364-2 spacer is not attached with flat-head
screws, perform the following procedures:
(a) Remove the spacer from the hub.
(b) Remove and discard the hub-to-spacer O-ring.
(10)If the C-7364-2 spacer is attached to the hub with flat-
head screws, perform the following procedures if the
O-ring must be replaced due to oil leakage.
(a) Remove the spacer attachment screws, if applicable.

Page 3-61
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(b) Remove the C-7364-2 spacer.

(c) Remove and discard the propeller hub-to-spacer
O-ring.
(11) Decompress and remove the beta system puller.
(12)Place the propeller on a suitable cart for transportation.
D. Removal of HC-B(3,4,5)( )( )-5( ) Propellers
WARNING: FOR SAFETY REASONS, THE
PROPELLER MUST BE PUT IN FEATHER
POSITION BEFORE IT IS REMOVED
FROM THE AIRCRAFT.

CAUTION: INSTRUCTIONS AND PROCEDURES IN

THIS SECTION MAY INVOLVE CRITICAL
PARTS. REFER TO THE INTRODUCTION
CHAPTER OF THIS MANUAL FOR
INFORMATION ABOUT PROPELLER
CRITICAL PARTS. REFER TO THE
ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL
MANUAL(S) FOR THE IDENTIFICATION
OF SPECIFIC PROPELLER CRITICAL
PARTS.
(1) Remove the spinner dome in accordance with the
procedure in the Spinner Dome Removal section of this
chapter.
(a) If the propeller is equipped with an ice protection
system that uses components supplied by Hartzell
Propeller Inc., applicable instructions and technical
information for the components supplied by
Hartzell Propeller Inc. can be found in the following
publications available on the Hartzell Propeller Inc.
website at www.hartzellprop.com:
1 Manual 180 (30-61-80) - Propeller Ice Protection
System Manual
2 Manual 181 (30-60-81) - Propeller Ice Protection
System Component Maintenance Manual
3 Manual 182 (61-12-82) - Propeller Electrical
De-ice Boot Removal and Installation Manual

Page 3-62
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

4 Manual 183 (61-12-83) - Propeller Anti-icing

Boot Removal and Installation Manual
(b) Propeller ice protection system components not
supplied by Hartzell Propeller Inc. are controlled by
the applicable TC or STC holder’s Instructions for
Continued Airworthiness (ICA).
CAUTION: THE BETA TUBE MUST BE REMOVED
BEFORE THE PROPELLER ASSEMBLY IS
REMOVED FROM THE AIRCRAFT. REFER
TO THE AIRCRAFT MAINTENANCE
INSTRUCTION MANUAL.
(2) Remove the beta tube.
WARNING 1: DURING ENGINE INSTALLATION OR
REMOVAL, USING THE PROPELLER TO
SUPPORT THE WEIGHT OF THE ENGINE
IS NOT AUTHORIZED. UNAPPROVED
INSTALLATION AND REMOVAL
TECHNIQUES MAY CAUSE DAMAGE TO
THE PROPELLER THAT MAY LEAD TO
FAILURE AND RESULT IN AN AIRCRAFT
ACCIDENT.

WARNING 2: DURING PROPELLER REMOVAL,

AIRFRAME MANUFACTURER’S
MANUALS AND PROCEDURES MUST
BE FOLLOWED BECAUSE THEY MAY
CONTAIN ISSUES VITAL TO AIRCRAFT
SAFETY THAT ARE NOT CONTAINED
IN THIS MANUAL OR THE HARTZELL
PROPELLER INC. OVERHAUL MANUALS
118F (61-10-18) AND 132A (61-10-32).

WARNING 3: MAKE SURE THE SLING IS RATED UP

TO 800 LBS (363 KG) TO SUPPORT THE
WEIGHT OF THE PROPELLER ASSEMBLY
DURING REMOVAL.
(3) Cut and remove the safety wire on the propeller
mounting bolts.

Page 3-63
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(4) Support the propeller assembly with a sling.

NOTE 1: Supporting the propeller with the sling may be
delayed until all but two mounting bolts and
washers have been removed to allow rotating
the propeller for ease of bolt removal.
NOTE 2: If the propeller will be reinstalled, and it
has been dynamically balanced, make an
identifying mark on the propeller hub and a
matching mark on the engine flange to ensure
proper orientation during re-installation to
prevent dynamic imbalance.
CAUTION: DISCARD THE PROPELLER MOUNTING
BOLTS IF THEY ARE DAMAGED OR
CORRODED, OR WHEN THE PROPELLER
IS REMOVED FOR OVERHAUL.
(5) Remove the propeller mounting bolts and washers.
NOTE: If the propeller is removed between overhaul
intervals, mounting bolts and washers may be
reused if they are not damaged or corroded.
CAUTION: USE ADEQUATE PRECAUTIONS TO
PROTECT THE PROPELLER ASSEMBLY
FROM DAMAGE WHEN IT IS REMOVED
FROM THE AIRCRAFT ENGINE AND
WHEN IT IS STORED.
(6) Using the support sling, lift the propeller from the
mounting flange.
(7) If the propeller has a two-piece spinner mounting plate,
proceed to paragraph 9.C.(9).
(8) Propellers with the one-piece spinner mounting plate
only (refer to Figure 3-11):
(a) Remove the spinner mounting plate, spinner
bulkhead and start locks, as a unit, from the
propeller hub flange.
(9) Remove and discard propeller mounting O-ring.
(10)Place the propeller on a suitable cart for transportation.

Page 3-64
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

E. Removal of HC-( )3( )( )-7( ) Propellers

CAUTION: INSTRUCTIONS AND PROCEDURES IN
THIS SECTION MAY INVOLVE CRITICAL
PARTS. REFER TO THE INTRODUCTION
CHAPTER OF THIS MANUAL FOR
INFORMATION ABOUT PROPELLER
CRITICAL PARTS. REFER TO THE
ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL
MANUAL(S) FOR THE IDENTIFICATION
OF SPECIFIC PROPELLER CRITICAL
PARTS.
NOTE: Refer to Figures 3-12 through 3-16 for the Beta
Valve System.
(1) Remove the spinner dome in accordance with the
procedure in the Spinner Dome Removal section of this
chapter.
(a) If the propeller is equipped with an ice protection
system that uses components supplied by Hartzell
Propeller Inc., applicable instructions and technical
information for the components supplied by
Hartzell Propeller Inc. can be found in the following
publications available on the Hartzell Propeller Inc.
website at www.hartzellprop.com:
1 Manual 180 (30-61-80) - Propeller Ice Protection
System Manual
2 Manual 181 (30-60-81) - Propeller Ice Protection
System Component Maintenance Manual
3 Manual 182 (61-12-82) - Propeller Electrical
De-ice Boot Removal and Installation Manual
4 Manual 183 (61-12-83) - Propeller Anti-icing
Boot Removal and Installation Manual
(b) Propeller ice protection system components not
supplied by Hartzell Propeller Inc. are controlled by
the applicable TC or STC holder’s Instructions for
Continued Airworthiness (ICA).

Page 3-65
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(2) Remove the self-locking nut and spacer from the beta
system rod that protrudes from the pitch change rod and
piston.
(3) Prepare the propeller for removal (see Figures 3-14
through 3-16).
(a) Piston Removal
1 Remove the flexlock nut with Hartzell Propeller
Inc. P/N AST-2917 or a 1 7/16 inch wrench, if
installed.
2 Remove the safety wire from the three link pin
units.
3 Remove the safety screws from the link pin units.
4 Remove the link pin units.
5 Mark the piston and link pins with a felt tip pen
or equivalent, so the piston can be reinstalled in
the same position.
6 Slide the link arms out of the piston slots.
7 Remove the socket head cap screw, jam nut,
and washer from each piston guide rod.
8 Slide the piston off the cylinder.
(b) Spring assembly removal.
1 Remove the ring retention plate screw safety
wire.
2 Remove the ring retention plate screws.
3 Remove the retention plate.
4 Remove the split retainer.
5 Remove the spring assembly from the cylinder.

Page 3-66
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

WARNING 1: DURING ENGINE INSTALLATION OR

REMOVAL, USING THE PROPELLER TO
SUPPORT THE WEIGHT OF THE ENGINE
IS NOT AUTHORIZED. UNAPPROVED
INSTALLATION AND REMOVAL
TECHNIQUES MAY CAUSE DAMAGE TO
THE PROPELLER THAT MAY LEAD TO
FAILURE AND RESULT IN AN AIRCRAFT
ACCIDENT.

WARNING 2: DURING PROPELLER REMOVAL,

AIRFRAME MANUFACTURER’S
MANUALS AND PROCEDURES MUST
BE FOLLOWED BECAUSE THEY MAY
CONTAIN ISSUES VITAL TO AIRCRAFT
SAFETY THAT ARE NOT CONTAINED
IN THIS MANUAL OR THE HARTZELL
PROPELLER INC. OVERHAUL MANUALS
118F (61-10-18) AND 132A (61-10-32).

WARNING 3: MAKE SURE THE SLING IS RATED UP

TO 800 LBS (363 KG) TO SUPPORT THE
WEIGHT OF THE PROPELLER ASSEMBLY
DURING REMOVAL.
(4) Cut and remove the safety wire on the propeller
mounting bolts.
(5) Support the propeller assembly with a sling.
NOTE 1: Supporting the propeller with the sling may be
delayed until all but two mounting bolts and
washers have been removed to allow rotating
the propeller for ease of bolt removal.
NOTE 2: If the propeller will be reinstalled, and it
has been dynamically balanced, make an
identifying mark on the propeller hub and a
matching mark on the engine flange to ensure
proper orientation during re-installation to
prevent dynamic imbalance.

Page 3-67
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

CAUTION: DISCARD THE PROPELLER MOUNTING

BOLTS IF THEY ARE DAMAGED OR
CORRODED, OR WHEN THE PROPELLER
IS REMOVED FOR OVERHAUL.
(6) Remove the propeller mounting bolts and washers.
NOTE: If the propeller is removed between overhaul
intervals, mounting bolts and washers may be
reused if they are not damaged or corroded.
CAUTION 1: DO NOT ALLOW THE PROPELLER
ASSEMBLY TO HIT OR REST ON THE
BETA FEEDBACK ROD. THIS COULD
BEND OR OTHERWISE DAMAGE THE
ROD.

CAUTION 2: USE ADEQUATE PRECAUTIONS TO

PROTECT THE PROPELLER ASSEMBLY
FROM DAMAGE WHEN IT IS REMOVED
FROM THE AIRCRAFT ENGINE AND
WHEN IT IS STORED.
(7) Using the support sling, lift the propeller from the
mounting flange.
(8) Remove and discard the propeller mounting O-ring.
(9) Place the propeller on a suitable cart for transportation.
F. Removal of Beta Valve Assembly for
HC-( )3( )( )-7( ) Propellers
(1) Remove the beta light switch from the beta valve pin per
airframe manufacturer’s instructions.
(2) Remove the engine mounted beta system control
hardware from the beta valve rod end fitting, per the
airframe/engine manufacturer’s instructions.
(3) Loosen the check nut on the push rod spool from the
bushing to break the Loctite® bond.
(4) Loosen the set screw to clear the threads of the push
rod spool and to allow removal of the rod end cap.
(5) Loosen the rod end cap to break the Loctite® bond and
remove the rod end cap from the push rod spool.

Page 3-68
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(6) Remove the rod end fitting from the push rod spool.
(7) Remove the bushing from the push rod spool.
(8) Remove the check nut from the push rod spool.
(9) Remove the O-ring from the cavity at the rear of the
threaded end of the push rod spool.
(10)Remove the engine cover from the rear of the engine
gear box encircling the beta valve push rod spool per the
airframe or engine manufacturer’s instructions.
(11) Remove and discard the ID and OD O-rings from the
engine cover.
WARNING: TO AVOID INJURY, SPRINGS IN THE
ENGINE SHAFT ARE PRELOADED AND
MUST BE PROPERLY CONTROLLED
WHEN RELEASING THE SPRING
RETAINER.
(12)Secure the spring retainer and remove the retaining ring
that holds the spring retainer in place.
(13)Remove the spring retainer from the engine shaft and
beta valve.
(14)Remove the inner and outer springs from the engine
shaft and beta valve.
(15)Slide the beta valve’s remaining assembly and push rod
spool out of the engine shaft toward where the propeller
had been mounted.
(16)Place all beta valve parts together, including the self
locking nut and spacer that were removed to allow the
removal of the propeller assembly.

Page 3-69
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner’s Manual
139

(This page is intentionally blank.)

Page 3-70
INSTALLATION AND REMOVAL 61-00-39 Rev. 13 Jun/15
 Propeller Owner's Manual
139

CONTENTS
1. Operational Tests........................................................................4-3
A. Initial Run-Up..........................................................................4-3
B. Post-Run Check......................................................................4-3
C. Maximum RPM (Static) Hydraulic Low Pitch Stop Check.......4-3
D. Feathering Pitch Stop Adjustment..........................................4-4
E. Start Lock Unit Adjustment.....................................................4-4
F. Propeller Ice Protection System.............................................4-4
2. Troubleshooting .........................................................................4-4
A. Hunting and Surging...............................................................4-4
B. Engine Speed Varies with Airspeed........................................4-5
C. Loss of Propeller Control........................................................4-6
D. Failure to Feather (or feathers slowly)....................................4-6
E. Failure to Unfeather................................................................4-7
F. Start Lock Units Fail to Latch on Shutdown
(-2, -5 and some -3 Models)..................................................4-7
G. Vibration..................................................................................4-8
H. Propeller Overspeed...............................................................4-9
I. Propeller Underspeed.............................................................4-9
J. Oil or Grease Leakage..........................................................4-10

Page 4-1
TESTING AND TROUBLESHOOTING 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

(This page is intentionally blank.)

Page 4-2
TESTING AND TROUBLESHOOTING 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

1. Operational Tests
Following propeller installation, and before flight, the propeller
hydraulic system must be purged of air and proper operation
verified.
A. Initial Run-Up
(1) Perform engine start and warm-up per the Pilot's
Operating Handbook (POH).
(2) Cycle the condition lever throughout its operating blade
angle range from reverse or low to high (or as directed
by the POH).
NOTE: Air trapped in the propeller hydraulic system
will cause the pitch control to be imprecise and
may result in propeller surging.
(3) Repeat this procedure at least three times to purge air
from the propeller hydraulic system and to introduce
warmed oil to the cylinder.
NOTE: Pitch change response on the first operation
from low to high blade angle may be slow,
but should speed up on the second and third
cycles.
(4) Verify proper operation from reverse or low pitch, to high
pitch and throughout operating range.
(5) Shut down the engine in accordance with the POH.
WARNING: REFER TO THE AIRCRAFT MAINTENANCE
MANUAL FOR ADDITIONAL PROCEDURES
THAT MAY BE REQUIRED AFTER
PROPELLER INSTALLATION.
B. Post-Run Check
After engine shutdown, check the propeller for signs of
engine oil leakage.
C. Maximum RPM (Static) Hydraulic Low Pitch Stop Check
The Maximum RPM (hydraulic low pitch stop) is normally set
at the factory per the aircraft manufacturer's requirements,
and should not require any additional adjustment.
Adjustments may be required after maintenance or because
of specific aircraft variances.
Adjustments must be done in accordance with the airframe
manufacturer's specification, found in the airframe
manufacturer's manual.
Page 4-3
TESTING AND TROUBLESHOOTING 61-00-39 Rev. 7 Oct/02
 Propeller Owner's Manual
139
D. Feathering Pitch Stop Adjustment
The feathering pitch stop is set at the factory in accordance
with the aircraft manufacturer's recommendations. This stop
is adjustable only by an appropriately licensed propeller repair
station, aircraft manufacturer, or the Hartzell Propeller Inc.
factory.
E. Start Lock Unit Adjustment
Start lock units are set at the factory in accordance with
the aircraft manufacturer's recommendations. These are
adjustable only by an appropriately licensed propeller repair
station or at the Hartzell Propeller Inc. factory.
F. Propeller Ice Protection System
(1) Electric De-ice System
(a) Consult the Pilot Operating Handbook (including all
supplements) regarding flight into conditions of known
icing. The aircraft may not be certificated for flight in
known icing conditions, even though propeller de-ice
equipment is installed.
(b) Refer to the De-ice Systems chapter of this manual
for functional tests of the de-ice system.
(2) Anti-ice System
(a) Consult the Pilot Operating Handbook (including all
supplements) regarding flight into conditions of known
icing. The aircraft may not be certificated for flight in
known icing conditions, even though propeller anti-ice
equipment is installed.
(b) Refer to the Anti-ice and De-ice Systems chapter of
this manual for functional tests of the anti-ice system.
2. Troubleshooting
A. Hunting and Surging
Hunting is characterized by a cyclic variation in engine speed
above and below desired speed. Surging is characterized by a
large increase/decrease in engine speed, followed by a return
to set speed after one or two occurrences.
(1) If propeller is hunting, an appropriately licensed propeller
repair station should check:
(a) Governor
(b) Fuel control
(c) Synchrophaser or synchronizer

Page 4-4
TESTING AND TROUBLESHOOTING 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

(2) If propeller is surging:

(a) Perform the steps 1.A.(1) through 1.A.(5) in the
Operational Tests section of this chapter to release
trapped air from the propeller. If surging reoccurs, it
is most likely due to a faulty governor.
(b) Hunting and/or surging may also be caused by
friction or binding within the governor control, or
by internal propeller corrosion, which causes the
propeller to react slower to governor commands.
NOTE: The propeller must be tested on a test
bench at an appropriately licensed
propeller repair facility to isolate these
faults.
B. Engine Speed Varies with Airspeed
(1) Constant speed propeller models will experience small
variances in engine speed that are normal and are no
cause for concern.
(2) Increase in engine speed while descending or increasing
airspeed:
(a) Governor is not reducing oil volume.
(b) Friction in propeller.
(3) Decrease in engine speed while increasing airspeed:
(a) Governor pilot valve is stuck and is excessively
decreasing oil volume.
(b) Feathering command engaged on propeller pitch
control.
(4) Increase in engine speed while decreasing airspeed:
(a) Governor pilot valve is stuck and is excessively
increasing oil volume.
(5) Decrease in engine speed while decreasing airspeed:
(a) Governor is not increasing oil volume in propeller.
(b) Friction in propeller.

Page 4-5
TESTING AND TROUBLESHOOTING 61-00-39 Rev. 7 Oct/02
 Propeller Owner's Manual
139

C. Loss of Propeller Control

(1) Propeller goes to uncommanded high pitch (or feather)
(a) Loss of propeller oil pressure - check:
1 Governor pressure relief valve.
2 Governor drive.
3 Engine oil supply.
(b) Start lock not engaging.
(2) Propeller goes to uncommanded low pitch (high RPM)
(a) Governor pilot valve sticking.
(3) RPM increases with power and airspeed, propeller RPM
control has little or no effect.
(a) Excessive friction in blade bearings or pitch change
mechanism.
(b) Broken feathering spring.
(4) RPM control sluggish (especially on reducing RPM).
(a) Broken feathering spring.
D. Failure to Feather (or feathers slowly)
(1) Broken feathering spring.
(2) Check for proper function and rigging of propeller/
governor control linkage.
(3) Check governor drain function.
(4) Propeller must be checked for misadjustment or internal
corrosion (usually in blade bearings or pitch changing
mechanism) that results in excessive friction. This must
be accomplished at an appropriately licensed propeller
repair facility.

Page 4-6
TESTING AND TROUBLESHOOTING 61-00-39 Rev. 7 Oct/02
 Propeller Owner's Manual
139

E. Failure to Unfeather
(1) Check for proper function and rigging of propeller control
linkage.
(2) Check governor function.
(3) Propeller must be checked for misadjustment or internal
corrosion (usually in blade bearings or pitch change
mechanism) that results in excessive friction. This must
be accomplished at an appropriately licensed propeller
repair facility.
F. Start Lock Units Fail to Latch on Shutdown
(-2, -5 and some -3 Models)
(1) Propeller was feathered before shutdown.
(2) Shutdown occurred at high RPM with propeller control
off the low pitch stop.
(a) The problem may be solved by restarting the engine,
placing the propeller control in the proper shut down
position, and then shutting down the engine.
(b) For HC-B(3,4,5)( )( )-5( ), the problem may be solved
by using the engine auxiliary pump to reposition the
propeller on the start lock units.
(3) Excessive governor pump leakage.
The problem should be referred to an appropriately
licensed propeller repair facility.
(4) Broken start lock unit(s).
The problem should be referred to an appropriately
licensed propeller repair facility.

Page 4-7
TESTING AND TROUBLESHOOTING 61-00-39 Rev. 7 Oct/02
 Propeller Owner's Manual
139

G. Vibration
CAUTION: ANY VIBRATION THAT CAN BE
DESCRIBED AS APPEARING SUDDENLY,
OR IS ACCOMPANIED BY UNEXPLAINED
GREASE LEAKAGE, SHOULD BE
INVESTIGATED IMMEDIATELY BEFORE
FURTHER FLIGHT.
NOTE: Vibration problems due to propeller system
imbalance are normally felt throughout the RPM
range, with the intensity of vibration increasing
with RPM. Vibration problems that occur in a
narrow RPM range are a symptom of resonance,
that is potentially harmful to the propeller. Avoid
operation in that RPM range until the propeller can
be checked by an appropriately licensed propeller
repair facility.
(1) Check:
(a) Control surfaces, exhaust system, landing gear
doors, etc. for excessive play, which may be causing
vibration unrelated to the propeller.
(b) Secure attachment of engine mounted hardware.
(c) Engine mount wear.
(d) Uneven lubrication of propeller.
(e) Proper engine/propeller flange mating.
(f) Blade track. (For procedure, refer to the Inspection
and Check chapter of this manual.)
(g) Blade angles:
Blade angle must be within 0.2 degree from blade
to blade at the reference station. (For HC-B5M(A,
P)-3(A, C, D, F) propellers installed on Air Tractor
aircraft, low pitch angles must be within a blade-to-
blade tolerance of 0.2 degrees at the 36, 42, 48, and
54 inch stations.)

Page 4-8
TESTING AND TROUBLESHOOTING 61-00-39 Rev. 7 Oct/02
 Propeller Owner's Manual
139

(h) Spinner for cracks, improper installation, or wobble

during operation.
(i) Static balance.
(j) Airfoil profile identical between blades (after overhaul
or rework for nicks - verify at an appropriately
licensed propeller repair facility.
(k) Hub, blade or blade clamp for damage or cracking.
(l) Grease or oil leakage from a seemingly solid surface
of the hub, blade clamp or blade.
(m) Blade deformation.
NOTE: Dynamic balancing is recommended after
installing or performing maintenance on
a propeller. While normally an optional
task, it may be required by the engine or
airframe manufacturer to make certain the
propeller/engine combination is balanced
within close tolerances before operation.
Refer to the engine or airframe manuals,
and the Maintenance Practices chapter of
this manual.
H. Propeller Overspeed
(1) Check:
(a) Low pitch stop adjustment.
(b) Governor maximum RPM set too high.
(c) Broken feathering spring.
(d) Governor pilot valve jammed, supplying high
pressure only.
(e) Tachometer error.
I. Propeller Underspeed
(1) Check:
(a) Governor oil pressure low.
(b) Governor oil passage clogged.
(c) Tachometer error.

Page 4-9
TESTING AND TROUBLESHOOTING 61-00-39 Rev. 7 Oct/02
 Propeller Owner's Manual
139

J. Oil or Grease Leakage

CAUTION: GREASE LEAKAGE THAT CAN BE
DESCRIBED AS EXCESSIVE AND
APPEARING SUDDENLY, ESPECIALLY
WHEN ACCOMPANIED BY VIBRATION,
SHOULD BE INVESTIGATED
IMMEDIATELY BEFORE FURTHER
FLIGHT.
(1) Grease Leakage - Probable Cause:
(a) Overlubrication
(b) Improperly torqued or loose lubrication fitting.
Tighten the fitting and torque in accordance with the
Torque Values Table found in the Installation and
Removal chapter of this manual.
(c) Defective lubrication fitting. (Replace the fitting.)
(d) Incorrect or damaged O-ring between the
blade clamp and the propeller hub. (Refer to an
appropriately licensed propeller repair facility. for
replacement of the O-ring).
(e) Grease leaks past the blade clamp seal gaskets.
(Refer to an appropriately licensed propeller repair
facility for replacement of the gasket.)
(f) Grease leaks from between the blade clamp and the
blade. (Refer to an appropriately licensed propeller
repair facility for replacement of sealant.)
(g) Improper application of silicone sealant on the clamp
radius of the bearing-to-clamp interface. (Refer to
an appropriately licensed propeller repair facility for
reapplication of silicone sealant.)
(h) Grease leaks from the clamp when the blade is
pointed up and in a static position.
1 Oil separating from the grease. Approved
propeller lubricants are listed in the
Maintenance Practices chapter of this manual.
These lubricants have varying separation rates.
If a clamp seal leaks after the first ten hours
of operation, consult an appropriately licensed
propeller repair facility.

Page 4-10
TESTING AND TROUBLESHOOTING 61-00-39 Rev. 7 Oct/02
 Propeller Owner's Manual
139

(2) Oil Leakage - Probable Cause

(a) Faulty or missing O-ring seal between the hub and
the cylinder.
(b) Faulty or missing O-ring seal between the piston and
the cylinder at the front of the piston.
(c) Displaced felt seal between the piston and the
cylinder
(d) Faulty or missing O-ring between the propeller hub
and the engine flange.
NOTE: The HC-B(3,4)( )W-3( ) propeller models
have an additional O-ring between the
spacer and hub flange.
(e) Faulty or missing O-ring between the piston and the
pitch change rod.

Page 4-11
TESTING AND TROUBLESHOOTING 61-00-39 Rev. 10 Jun/11
 Propeller Owner's Manual
139

(This page is intentionally blank.)

Page 4-12
TESTING AND TROUBLESHOOTING 61-00-39 Rev. 10 Jun/11
 Propeller Owner’s Manual
139

INSPECTION AND CHECK - CONTENTS

1. Pre-Flight Checks........................................................................5-3
2. Post-Flight Checks......................................................................5-5
3. Operational Checks.....................................................................5-6
4. Required Periodic Inspections and Maintenance........................5-7
A. Periodic Inspections...............................................................5-7
B. Periodic Maintenance............................................................5-8
C. Compliance Inspections.........................................................5-8
D. Airworthiness Limitations..................................................... 5-11
E. Overhaul Periods.................................................................5-12
5. Inspection Procedures..............................................................5-13
A. Blade Damage.....................................................................5-13
B. Grease or Oil Leakage.........................................................5-13
C. Vibration...............................................................................5-15
D. Tachometer Inspection..........................................................5-16
E. Blade Track..........................................................................5-19
F. Loose Blades.......................................................................5-20
G. Corrosion.............................................................................5-20
H. Spinner Damage..................................................................5-20
I. Electric De-ice System.........................................................5-20
J. Anti-ice System....................................................................5-21
6. Special Inspections...................................................................5-21
A. Overspeed/Overtorque........................................................5-21
B. Propeller Ground Idle Operating Restrictions......................5-24
C. Lightning Strike....................................................................5-30
D. Foreign Object Strike...........................................................5-31
E. Fire Damage or Heat Damage.............................................5-33
7. Long Term Storage....................................................................5-34

Page 5-1
INSPECTION AND CHECK 61-00-39 Rev. 12 Mar/13
 Propeller Owner’s Manual
139

INSPECTION AND CHECK - FIGURES

Checking Blade Track..................................... Figure 5-1.............5-18

Blade Play....................................................... Figure 5-2.............5-18
Turbine Engine Overspeed Limits.................. Figure 5-3.............5-22
Turbine Engine Overtorque Limits.................. Figure 5-4.............5-23
Example of an Evaluation of Ground
Idle RPM Check........................................ Figure 5-5.............5-25
Corrective Action Required.............................. Figure 5-6.............5-26

Page 5-2
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

1. Pre-Flight Checks
CAUTION: INSTRUCTIONS AND PROCEDURES IN THIS
SECTION MAY INVOLVE CRITICAL PARTS.
REFER TO THE INTRODUCTION CHAPTER
OF THIS MANUAL FOR INFORMATION ABOUT
PROPELLER CRITICAL PARTS. REFER TO
THE ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL MANUAL(S)
FOR THE IDENTIFICATION OF SPECIFIC
PROPELLER CRITICAL PARTS.
Follow propeller preflight inspection procedures as specified in
the Pilot Operating Handbook (POH) or this manual. In addition,
perform the following inspections:
A. Blades
(1) Visually inspect the entire blade (lead, trail, face, and
camber sides) for nicks, gouges, and cracks. Refer to
the Maintenance Practices chapter of this manual for
blade repair information. Normal blade lead edge erosion
(sand-blasted appearance) is acceptable, and does not
require removal before further flight.
(2) Visually inspect the blades for lightning strike. Refer to
the Lightning Strike Damage information in the Special
Inspections section of this chapter for a description of
damage.
B. Inspect the spinner and visible blade retention components
for damage or cracks. Repair or replace components as
required before further flight.
C. Check for loose/missing hardware. Retighten or reinstall as
necessary.
WARNING: ABNORMAL GREASE LEAKAGE CAN BE
AN INDICATION OF A FAILING PROPELLER
BLADE OR BLADE RETENTION COMPONENT.
AN IN-FLIGHT BLADE SEPARATION CAN
RESULT IN A CATASTROPHIC AIRCRAFT
ACCIDENT.
D. Inspect for grease and oil leakage and determine its source.

Page 5-3
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

E. Check the blades for radial play or movement of the blade

tip (in and out or back and forth). Refer to Loose Blades in
the Periodic Inspections section of this chapter for blade play
limits.
F. Inspect de-ice boots (if installed) for damage. Refer to
the De-ice Systems chapter of this manual for inspection
information.
WARNING: ABNORMAL VIBRATION CAN BE AN
INDICATION OF A FAILING PROPELLER
BLADE OR BLADE RETENTION COMPONENT.
AN IN-FLIGHT BLADE SEPARATION CAN
RESULT IN A CATASTROPHIC AIRCRAFT
ACCIDENT.
G. Refer to Periodic Inspections within this section for additional
inspection information and possible corrections to any
discrepancies discovered as a result of pre-flight checks.

Page 5-4
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

2. Post-Flight Checks
CAUTION: INSTRUCTIONS AND PROCEDURES IN THIS
SECTION MAY INVOLVE CRITICAL PARTS.
REFER TO THE INTRODUCTION CHAPTER
OF THIS MANUAL FOR INFORMATION ABOUT
PROPELLER CRITICAL PARTS. REFER TO
THE ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL MANUAL(S)
FOR THE IDENTIFICATION OF SPECIFIC
PROPELLER CRITICAL PARTS.
A. HC-B3TN-3DL/LT10282( )-9.5R propellers installed on
Piaggio P-166 DL3 aircraft
(1) As a result of the “pusher” configuration, propeller
blades on affected aircraft are exposed to hot exhaust
gasses, which makes them more susceptible to erosion
and corrosion. Additional inspections and corrosion
preventative measures are required.
(a) Perform blade cleaning within three days after any
flight.
NOTE: It is recommended to perform blade
cleaning after the last flight of each day.
(b) Blade Cleaning
1 Use a cloth dampened with an approved solvent/
cleaner to thoroughly clean each blade shank
where exposed to engine exhaust and remove
all foreign matter/exhaust residue.
2 Visually inspect for corrosion indications and
paint condition.
3 Paint must be in good condition in the area
exposed to exhaust gasses. Repair and repaint
in accordance with the Maintenance Practices
Chapter of this manual or by an appropriately
licensed propeller repair facility if:
a Any of the underlying aluminum blade is
exposed.
b There are any indications of corrosion, such
as pitting or any other unusual conditions.

Page 5-5
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

3. Operational Checks
CAUTION: INSTRUCTIONS AND PROCEDURES IN THIS
SECTION MAY INVOLVE CRITICAL PARTS.
REFER TO THE INTRODUCTION CHAPTER
OF THIS MANUAL FOR INFORMATION
ABOUT PROPELLER CRITICAL PARTS.
REFER TO THE ILLUSTRATED PARTS LIST
CHAPTER OF THE APPLICABLE OVERHAUL
MANUAL(S) FOR THE IDENTIFICATION OF
SPECIFIC PROPELLER CRITICAL PARTS.
A. Following propeller installation or as required, perform initial
run-up as outlined in Operational Tests in the Testing and
Troubleshooting chapter of this manual.
B. Check the propeller speed control and operation from
reverse or low pitch to high pitch, using the procedure
specified in the Pilot Operating Handbook (POH) for the
aircraft.
WARNING: ABNORMAL VIBRATION CAN BE AN
INDICATION OF A FAILING PROPELLER
BLADE OR BLADE RETENTION COMPONENT.
AN IN-FLIGHT BLADE SEPARATION CAN
RESULT IN A CATASTROPHIC AIRCRAFT
ACCIDENT.
C. Check for any abnormal vibration during this run-up. If vibration
occurs, shut the engine down, determine the cause, and
correct it before further flight. Refer to the Vibration section in
the Testing and Troubleshooting chapter of this manual.
D. Refer to Periodic Inspections in this chapter for additional
inspection information and possible corrections to any
discrepancies discovered as a result of Pre-Flight Checks.
E. Refer to the airframe manufacturer’s manual for additional
operational checks.

Page 5-6
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

4. Required Periodic Inspections and Maintenance

CAUTION: INSTRUCTIONS AND PROCEDURES IN
THIS SECTION MAY INVOLVE CRITICAL
PARTS. REFER TO THE INTRODUCTION
CHAPTER OF THIS MANUAL FOR
INFORMATION ABOUT PROPELLER
CRITICAL PARTS. REFER TO THE
ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL
MANUAL(S) FOR THE IDENTIFICATION
OF SPECIFIC PROPELLER CRITICAL
PARTS.
A. Periodic Inspections
(1) Complete detailed inspection procedures at 400 hour
intervals, not to exceed twelve (12) calendar months.
(a) Inspection and maintenance specified by an airframe
manufacturer’s maintenance program and approved
by the applicable airworthiness agency may not
coincide with the inspection time interval specified.
In this situation the airframe manufacturer’s
schedule may be applied with the exception that
the calendar limit for the inspection interval may not
exceed (12) calendar months.
(b) Refer to Inspection Procedures in this chapter
for additional inspection information and possible
corrections to any discrepancies discovered as a
result of the Periodic Inspection.
(2) Remove the spinner dome.
(3) Visually inspect the entire blade for nicks and cracks. If
any damage is discovered, refer to the Blade Repairs
section in the Maintenance Practices chapter of this
manual for additional information.
(a) A cracked blade must be referred to an appropriately
licensed propeller repair facility.
(4) Inspect all visible propeller parts for cracks, wear, or
unsafe conditions.

Page 5-7
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

(5) Check for oil and grease leaks. Refer to Oil and Grease
Leakage in the Inspection Procedures section of this
chapter.
(6) If a blade track problem is suspected, check the blade
track. Refer to Blade Track in the Inspection Procedures
section of this chapter.
(7) Make an entry in the log book verifying this inspection.
B. Periodic Maintenance
Lubricate the propeller assembly. Refer to Lubrication in the
Maintenances Practices chapter of this manual for intervals
and procedures.
C. Compliance Inspections
(1) B-834-20 and B-834-22 Guide Collars
(a) This inspection applies to B-834-20 and B-834-22
guide collars installed on HC-B3TN-5(M,N,P)(L)
propellers with serial numbers below BV-4870 (right
hand rotation), and BV-4862 (left hand rotation).
NOTE: An “L” following the propeller model
number denotes left hand rotation, i.e.,
HC-B3TN-5(M,N,P)L.
(b) These guide collars require inspection for cracks
between the surface of the guide collar and the thin
wall of the counterbored hole where the guide collar
screw is inserted. This repetitive inspection must be
performed at 500 hour intervals.
(c) Record compliance with this inspection in the
propeller logbook.
(d) If a crack is found, an appropriately licensed
propeller repair facility must replace both the guide
collar and the start lock units with current parts
configurations identified in Hartzell Propeller Inc.
Manual 118F (61-10-18). Replacing the guide
collar and start lock units with the current parts
configurations terminates this inspection.

Page 5-8
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

(2) Blade Inspection for HC-B3TN-3DL/LT10282( )-9.5R

Propellers Installed on Piaggio P166 DL3 Aircraft
CAUTION: ESTABLISH MORE FREQUENT
INTERVALS FOR INSPECTION IF
SERVICE EXPERIENCE INDICATES
THAT SEVERE CORROSION IS
FOUND DURING INSPECTIONS.
(a) Visually inspect each blade for paint erosion and
corrosion at intervals not exceeding 150 hours
of operation,12 calendar months, or at annual
inspection, whichever occurs first.
1 For scheduling purposes, the inspection interval
has a maximum 10 percent additional
non-cumulative flight hour tolerance.
a For example, the initial 150 hour inspection
is overflown to 160 hours, and then
inspected at this time. The next inspection
must be accomplished 140 flight hours from
previous inspection.
WARNING: CLEANING AGENTS (ACETONE, #700
LACQUER THINNER, AND MEK), ARE
FLAMMABLE AND TOXIC TO THE SKIN,
EYES, AND RESPIRATORY TRACT. SKIN
AND EYE PROTECTION ARE REQUIRED.
AVOID PROLONGED CONTACT. USE IN
WELL VENTILATED AREA.
2 Use a cloth dampened with an approved solvent/
cleaner to thoroughly clean each blade shank
where exposed to engine exhaust and remove
all foreign matter/exhaust residue.
3 Paint must be in good condition in the area
exposed to exhaust gasses. Repair and
repainting is required if:
a Any of the underlying aluminum blade is
exposed.
b There are any indications of corrosion, such
as pitting or any other unusual conditions.

Page 5-9
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

4 All corrosion indications require repair and

subsequent repainting by an appropriately
licensed propeller repair facility.
a Refer to FAA Advisory Circular
AC 43.4A (or subsequent revision) for
additional information concerning corrosion.
This circular provides definitions, repair
procedures, safety precautions, etc.
(b) If repair and repainting are required, refer to the
Blade Repairs section in the Maintenance Practices
chapter of this manual for additional information.
NOTE: Qualified personnel must make the
determination if repairs can be made
locally or must be sent to an appropriately
licensed propeller repair facility. Hartzell
Propeller Inc. recommends that in
“borderline” or questionable situations it
is preferable to send the propeller to an
appropriately licensed propeller repair
facility.
(c) Record compliance with this inspection in the
propeller logbook.

Page 5-10
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

D. Airworthiness Limitations
(1) Certain components, as well as the entire propeller
may have specific life limits established as part of the
certification by the FAA. Such limits call for mandatory
replacement of specified parts after a defined number of
hours and/or cycles of use.
(2) Life limited component times may exist for the propeller
models covered in this manual. Life limited components
will be identified in the Airworthiness Limitations chapter
of this manual.
(3) Refer to the latest revision of Hartzell Propeller Inc.
Service Letter HC-SL-61-61Y for life limited data that
has not yet been incorporated into the Airworthiness
Limitations chapter of this manual.
(4) Operators are urged to keep informed of airworthiness
information via Hartzell Propeller Inc. Service Bulletins
and Service Letters, which are available from Hartzell
Propeller Inc. distributors or from the Hartzell Propeller
Inc. factory by subscription. Selected information is also
available on Hartzell Propeller’s website at
www.hartzellprop.com.

Page 5-11
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

E. Overhaul Periods
In flight, the propeller is constantly subjected to vibration
from the engine and the airstream, as well as high centrifugal
forces. The propeller is also subject to corrosion, as well as
general deterioration due to aging. Under these conditions,
metal fatigue or mechanical failures can occur. In order to
protect your investment, and to maximize the safe operating
lifetime of your propeller, it is essential that a propeller
be properly maintained and overhauled according to the
recommended service procedures.
CAUTION 1: OVERHAUL PERIODS LISTED BELOW,
ALTHOUGH CURRENT AT THE TIME OF
PUBLICATION, ARE FOR REFERENCE
PURPOSES ONLY. OVERHAUL PERIODS
MAY BE INCREASED OR DECREASED
AS A RESULT OF ENGINEERING
EVALUATION.

CAUTION 2: CHECK THE LATEST REVISION OF

HARTZELL PROPELLER INC. SERVICE
LETTER HC-SL-61-61Y FOR THE
MOST CURRENT INFORMATION. THE
SERVICE LETTER IS AVAILABLE ON THE
HARTZELL PROPELLER INC. WEBSITE AT
WWW.HARTZELLPROP.COM.
(1) Hartzell Propeller Inc. steel hub propellers installed on
turbine engine aircraft are to be overhauled at 3000
hours of operation or 60 calendar months, whichever
occurs first.
(2) Agricultural aircraft are to be overhauled at 3000 hours
of operation or 36 calendar months, whichever occurs
first.
(a) Once used on agricultural aircraft, the 36 month
overhaul limit must be maintained until an overhaul
is accomplished, even if the propeller is later
installed on other category airplanes.

Page 5-12
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

5. Inspection Procedures
CAUTION: INSTRUCTIONS AND PROCEDURES IN THIS
SECTION MAY INVOLVE CRITICAL PARTS.
REFER TO THE INTRODUCTION CHAPTER
OF THIS MANUAL FOR INFORMATION ABOUT
PROPELLER CRITICAL PARTS. REFER TO
THE ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL MANUAL(S)
FOR THE IDENTIFICATION OF SPECIFIC
PROPELLER CRITICAL PARTS.
The inspections detailed below are made on a regular basis,
either before flight, during required periodic inspections, or if a
problem is noted. Possible corrections to problems discovered
during inspections, additional inspections, and limits are detailed
in the following inspection procedures.
A. Blade Damage
Refer to Blade Repairs section in the Maintenance Practices
chapter of this manual for information regarding blade
damage.
B. Grease or Oil Leakage
WARNING: UNUSUAL OR ABNORMAL GREASE
LEAKAGE OR VIBRATION, WHERE
THE CONDITION STARTED SUDDENLY,
CAN BE AN INDICATION OF A FAILING
PROPELLER BLADE OR BLADE
RETENTION COMPONENT. AN INFLIGHT
BLADE SEPARATION CAN RESULT IN
DEATH, SERIOUS BODILY INJURY, AND/
OR SUBSTANTIAL PROPERTY DAMAGE.
UNUSUAL OR ABNORMAL GREASE
LEAKAGE OR VIBRATION REQUIRES
IMMEDIATE INSPECTION FOR A
POSSIBLE CRACKED BLADE OR BLADE
RETENTION COMPONENT.
NOTE: A new or newly overhauled propeller may leak
slightly during the first several hours of operation.
This leakage may be caused by the seating of
seals and O-rings, and the slinging of lubricants
used during assembly. Such leakage should cease
within the first ten hours of operation.

Page 5-13
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

Leakage that persists beyond the first ten hours of operation

on a new or newly overhauled propeller, or occurs on a
propeller that has been in service for some time will require
repair. A determination should be made as to the source
of the leak. The only leakage that is field repairable is the
removal and replacement of the O-ring seal between the
engine and propeller flange. All other leakage repairs should
be referred to an appropriately licensed propeller repair
facility. An instance of abnormal grease leakage should be
inspected following the procedure below:
(1) Remove the spinner dome.
CAUTION: PERFORM A VISUAL INSPECTION
WITHOUT CLEANING THE PARTS. A
TIGHT CRACK IS OFTEN EVIDENT DUE
TO TRACES OF GREASE EMANATING
FROM THE CRACK. CLEANING CAN
REMOVE SUCH EVIDENCE AND MAKE A
CRACK VIRTUALLY IMPOSSIBLE TO SEE.
(2) Perform a visual inspection of the blade clamps to locate
the origin of leakage. If the origin of the grease leakage
is determined to be a noncritical part, such as an O-ring,
gasket or sealant, repairs can be accomplished during
scheduled maintenance, as long as flight safety is not
compromised.
(3) If cracks in the blade clamp are suspected, perform
additional inspections before further flight (by qualified
personnel at an appropriately licensed propeller repair
facility) to verify the condition. Such inspections typically
include disassembly of the propeller, followed by
inspection of parts, using non-destructive methods in
accordance with published procedures.
(4) If cracks or failing components are found, these parts
must be replaced before further flight. Report such
occurrences to airworthiness authorities and to Hartzell
Propeller Inc. Product Support.

Page 5-14
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

C. Vibration
Instances of abnormal vibration should be investigated
immediately. If the cause of the vibration is not readily
apparent, the propeller may be inspected following the
procedure below:
NOTE: It may sometimes be difficult to readily identify the
cause of abnormal vibration. Vibration may
originate in the engine, propeller, or airframe.
Troubleshooting procedures typically begin with an
investigation of the engine. Airframe components,
such as engine mounts or loose landing gear
doors, can also be the source of vibration. When
investigating an abnormal vibration, the possibility
of a failing blade or blade retention component
should be considered as a potential source of the
problem.
(1) Perform troubleshooting and evaluation of possible
sources of vibration in accordance with engine or
airframe manufacturer’s instructions.
(2) Refer to Vibration section in the Testing and
Troubleshooting chapter of this manual. Perform the
checks to determine possible cause of the vibration. If no
cause is found, then consider the origin of the problem
could be the propeller and proceed with steps 4.C.(3)
through 4.C.(8).
(3) Remove the spinner dome.
(4) Perform a visual inspection for cracks in the hub, blade
clamps and blades.
NOTE: A crack may be readily visible or may be
indicated by grease leaking from a seemingly
solid surface.
(5) If cracks in the hub or the blade clamp are suspected,
additional inspections must be performed before
further flight. These inspections must be performed by
qualified personnel at an appropriately licensed propeller
repair facility to verify the condition. Such inspections
typically include disassembly of the propeller followed
by inspection of parts, using nondestructive methods in
accordance with published procedures.

Page 5-15
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

(6) Check the blades and compare blade to blade

differences:
(a) Inspect the propeller blades for unusual looseness
or movement. Refer to Loose Blades in this chapter.
(b) Check blade track. Refer to Blade Track in this
chapter.
CAUTION: DO NOT USE BLADE PADDLES TO
TURN BLADES.
(c) Manually (by hand) attempt to turn the blades
(change pitch).
(d) Visually check for damaged blades.
(7) If abnormal blade conditions or damage are found,
perform additional inspections (by qualified personnel
at an appropriately licensed propeller repair facility)
to evaluate the condition. Refer to the Blade Repairs
section in Maintenance Practices chapter of this manual.
(8) If cracks or failing components are found, these parts
must be replaced before further flight. Report such
occurrences to airworthiness authorities and Hartzell
Propeller Inc. Product Support.
D. Tachometer Inspection
WARNING: OPERATION WITH AN INACCURATE
TACHOMETER MAY RESULT IN
RESTRICTED RPM OPERATION AND
DAMAGING HIGH STRESSES. BLADE
LIFE WILL BE SHORTENED AND COULD
RESULT IN CATASTROPHIC FAILURE.
(1) Accuracy of the engine tachometer should be verified
at 100 hour intervals or at annual inspection, whichever
occurs first.
(2) Hartzell Propeller Inc. recommends using a tachometer
that is accurate within +/- 10 RPM, has NIST calibration
(traceable), and has an appropriate calibration schedule.

Page 5-16
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

(This page is intentionally blank.)

Page 5-17
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

W10144

Checking Blade Track

Figure 5-1

W10143
FORE AND AFT PLAY

BLADE END PLAY

RADIAL PLAY

Blade Play
Figure 5-2

Page 5-18
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

E. Blade Track
(1) On -2 and -5 propeller models only, check the blade
track as follows:
(a) Chock the aircraft wheels securely.
(b) Refer to Figure 5-1. Place a fixed reference point
beneath the propeller, within 0.25 inch (6.4 mm) of
the lowest point of the propeller arc.
NOTE: This reference point may be a flat board
with a sheet of paper attached to it. The
board may then be blocked up to within
0.25 inch (6.4 mm) of the propeller arc.
(c) Rotate the propeller by hand in the direction of
normal rotation until a blade points directly at the
paper. Mark the position of the blade tip in relation to
the paper.
(d) Repeat this procedure with the remaining blades.
(e) Tracking tolerance is + 0.062 inch (1.57 mm) or
0.125 inch (3.17 mm) total.
(2) On -3 and -7 propeller models only, the propeller must
be removed from the aircraft to check the blade track
on a rotatable fixture, in accordance with the applicable
Hartzell Propeller Inc. Manual 118F (61-10-18) or 132A
(61-10-32).
(3) Possible Correction
(a) Remove any foreign matter from the propeller
mounting flange.
(b) If no foreign matter is present, refer to an
appropriately licensed propeller repair facility.

Page 5-19
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

F. Loose Blades
Refer to Figure 5-2. Limits for blade looseness are as
follows:
End Play ± 0.06 inch (1.5 mm)
Fore & Aft Play ± 0.06 inch (1.5 mm)
Radial Play (pitch change) ± 0.5 degree (1 degree total)
measured at reference
station
In and Out 0.032 inch (0.81 mm)
NOTE: Blades are intended to be tight in the propeller;
however, movement less than allowable limits
is acceptable if the blade returns to its original
position when released. Blades with movement
greater than allowable limits, or that do not return
to their original position when released may
indicate internal wear or damage that should be
referred to an appropriately licensed propeller
repair station.
G. Corrosion
WARNING: REWORK THAT INVOLVES COLD
WORKING THE METAL, RESULTING IN
CONCEALMENT OF A DAMAGED AREA IS
NOT PERMITTED.
Light corrosion on blades may be removed by qualified
personnel in accordance with the Blade Repairs section in
the Maintenance Practices chapter of this manual.
Heavy corrosion that results in severe pitting must be
referred to an appropriately licensed propeller repair station.
H. Spinner Damage
Inspect the spinner for cracks, missing hardware, or other
damage. Refer to an appropriately licensed propeller
repair station for spinner damage acceptance and repair
information. Contact the local airworthiness authority for
repair approval.
I. Electric De-ice System
(1) Refer to the Anti-ice and De-ice Systems chapter of this
manual for inspection procedures.

Page 5-20
INSPECTION AND CHECK 61-00-39 Rev. 12 Mar/13
 Propeller Owner’s Manual
139

J. Anti-ice System
(1) Refer to the Anti-ice and De-ice Systems chapter of this
manual for inspection procedures.
6. Special Inspections
CAUTION: INSTRUCTIONS AND PROCEDURES IN THIS
SECTION MAY INVOLVE CRITICAL PARTS.
REFER TO THE INTRODUCTION CHAPTER
OF THIS MANUAL FOR INFORMATION ABOUT
PROPELLER CRITICAL PARTS. REFER TO
THE ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL MANUAL(S)
FOR THE IDENTIFICATION OF SPECIFIC
PROPELLER CRITICAL PARTS.
A. Overspeed/Overtorque
An overspeed has occurred when the propeller RPM has
exceeded the maximum RPM stated in the applicable Aircraft
Type Certificate Data Sheet. An overtorque condition occurs
when the engine load exceeds the limits established by the
engine, propeller, or airframe manufacturer. The duration of
time at overspeed/overtorque for a single event determines
the corrective action that must be taken to make sure no
damage to the propeller has occurred.
The criteria for determining the required action after an
overspeed are based on many factors. The additional
centrifugal forces that occur during overspeed are not the
only concern. Some applications have sharp increases in
vibratory stresses at RPMs above the maximum rated for the
airframe/engine/propeller combination
(1) When a propeller installed on a turbine engine has an
overspeed event, refer to the Turbine Engine Overspeed
Limits (Figure 5-3) to determine the corrective action to
be taken.
(2) When a propeller installed on a turbine engine has an
overtorque event, refer to the Turbine Engine Overtorque
Limits (Figure 5-4) to determine the corrective action to
be taken.
(3) Make an entry in the propeller log book to document the
overspeed/overtorque event.

Page 5-21
INSPECTION AND CHECK 61-00-39 Rev. 12 Mar/13
 W10069

125%

120%
Requires Evaluation by an
Appropriately Licensed Propeller
Repair Facility
115%

110%

INSPECTION AND CHECK

106% No Action Required
139

61-00-39
20 60 300 360

Percent Overspeed -- Turbine Engines Only

Propeller Owner’s Manual

Duration of Overspeed (in seconds)

Duration of Overspeed in Seconds

Turbine Engine Overspeed Limits

Rev. 11 Jul/12
Page 5-22
Figure 5-3
 120%

Contact Hartzell Product Support for Disposition

115%

110%

INSPECTION AND CHECK

No Action Required
102%
139

61-00-39
20 300

Percent Overtorque -- Turbine Engines Only

Propeller Owner’s Manual

Duration of Overtorque in Seconds

W10070

Turbine Engine Overtorque Limits

Rev. 13 Jun/15
Page 5-23
Figure 5-4
 Propeller Owner’s Manual
139

B. Propeller Ground Idle Operating Restrictions

WARNING: STABILIZED GROUND OPERATION
WITHIN THE PROPELLER RESTRICTED
RPM RANGE CAN GENERATE
HIGH PROPELLER STRESSES AND
RESULT IN FATIGUE DAMAGE TO THE
PROPELLER. THIS DAMAGE CAN LEAD
TO A REDUCED PROPELLER FATIGUE
LIFE, PROPELLER FAILURE, AND LOSS
OF CONTROL OF THE AIRCRAFT. THE
PROPELLER RESTRICTED RPM RANGE
IS DEFINED IN THE AIRPLANE FLIGHT
MANUAL.
(1) General
(a) The information in this section applies only to the
four and five bladed propeller models that are
addressed in this manual.
(b) The information in this section is intended to
emphasize the critical importance of correct propeller
ground idle RPM on certain turboprop installations.
It also defines the appropriate corrective action
required when a propeller has been operated within
this restricted RPM region.
(c) If the propeller is operated within a restricted RPM
range or below a minimum idle RPM restriction for
an extended period of time, the propeller blades and
hub can become unairworthy because of fatigue.
A failed blade or hub has the potential to cause a
catastrophic blade separation.
(d) Four, five and six blade propellers operating on
turbine engines can be sensitive to operation within
restricted RPM ranges. These restricted ranges
are usually in the lower RPM ranges, requiring that
ground idle RPM be set above a critical minimum
value.

Page 5-24
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

Example:

Minimum propeller idle RPM listed in the AMM is 1180 RPM

Propeller idle is set at 1120 RPM

Propeller has operated with a RPM deviation of 60 RPM

Engine was rigged 2 months ago and has operated 75 hours

since it was rigged

Figure 5-6 shows that with an RPM deviation of 60 RPM for 75

hours - the propeller assembly must be overhauled and engine
rigging corrected before further flight.

Example of an Evaluation of Ground Idle RPM Check

Figure 5-5

Page 5-25
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

Before further flight - retire the blades

Number of RPM below Minimum Propeller Idle RPM

and hub from service and overhaul the

remaining components. Correct engine
rigging during propeller reinstallation.
80

60
Before further flight - overhaul
the propeller assembly and correct engine
rigging during propeller reinstallation.
40
Before Further Flight - adjust engine rigging to prevent
operation below the specified minimum RPM.

20
No Immediate Action Required - adjust engine rigging to
prevent operation below the specified minimum RPM.

0 25 50 75 100

Total hours of operation the propeller has operated on an

engine with improper RPM setting.

To determine Corrective Action, refer to Figure 5-5.

Corrective Action Required

Figure 5-6

Page 5-26
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

(e) This minimum propeller idle RPM operating

restriction is the result of a specific vibratory
resonant condition known as “reactionless mode”.
During operation in these conditions the flight crew
cannot feel the resulting high propeller vibration.
Ground operation at or near an RPM that can create
a reactionless mode vibratory resonance can cause
very high stresses in the propeller blades and the
hub. These high stresses are more severe when
operating in a tailing wind condition.
(2) Periodic Ground Idle RPM Check
(a) Perform the RPM check, especially following engine
rigging/idle RPM adjustments.
(b) Refer to the Airplane Flight Manual or Airplane Flight
Manual Supplement to determine if there are any
propeller RPM restrictions or limitations.
(c) Check the accuracy of the tachometer. Refer to the
Tachometer Inspection section in this chapter.
(d) Perform an engine run up and determine if the
engine and/or propeller rigging permits operation of
the propeller below the minimum specified propeller
idle RPM.
(e) If the propeller cannot be operated below the
minimum specified propeller idle RPM, no further
action is required.
(f) If the propeller can be operated below the minimum
specified propeller idle RPM:
1 Refer to Figure 5-6 for corrective action. Refer to
Figure 5-5 for help when using Figure 5-6.

Page 5-27
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

2 The corrective action is based on the amount the

RPM is below the minimum propeller idle RPM
and the total hours of operation the propeller has
accumulated.
a Figure 5-6 applies to an aircraft that is
operated in conventional service. “Hours
of Operation” refers to the total number
of hours the propeller is operated on an
engine that has an improper RPM setting. It
is not the number of hours the propeller is
operated in a restricted range, which will be
less than the total hours of operation.
(3) Corrective Action
(a) The required corrective action is determined by both
the amount and duration of RPM deviation.
1 A turboprop propeller with four or more blades
may have a variety of operating restrictions and
these different restrictions may have different
operating margins.
2 The greater the amount of the RPM deviation
and the longer it is permitted to exist, the more
severe the required corrective action.
3 The corrective action may vary from no action
required to scrapping of the blades and the hub.
4 Refer to Figure 5-6 for the required corrective
action.
5 Contact Hartzell Propeller Inc. if further
clarification is required.
6 If a propeller restriction other than those
described in Figure 5-6 has been violated,
contact Hartzell Propeller Inc.
a The chart in Figure 5-6 applies only to
operation below the minimum idle RPM.
b The chart in Figure 5-6 does not apply to
other propeller restrictions that are above
the minimum idle RPM.

Page 5-28
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

7 If the corrective action requires a propeller

overhaul, overhaul the propeller in accordance
with the applicable propeller overhaul manuals.
8 If the corrective action requires that the blades
and the hub be retired from service, retire these
components from service in accordance with the
Part Retirement Procedures chapter of Hartzell
Propeller Inc. Standard Practices Manual 202A
(61-01-02).
9 A propeller hub or blade that has been retired
from service because of a violation of the
operating restrictions as specified in this
section must not be reused on another aircraft
application.
10 If the corrective action requires the correction of
the propeller RPM setting, refer to the applicable
installation and rigging instructions for the
adjustment of engine torque, engine idle speed,
and propeller RPM setting.
11 Contact Hartzell Propeller Inc. Product Support
Department to report the findings.
Hartzell Propeller Inc.
One Propeller Place
Piqua, Ohio 45356-2634 USA
Phone: 937.778.4379
Fax: 937.778.4391
E-mail: [email protected]

Page 5-29
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

C. Lightning Strike
CAUTION: ALSO CONSULT ENGINE AND AIRFRAME
MANUFACTURER’S MANUALS. THERE
MAY BE ADDITIONAL REQUIREMENTS,
SUCH AS DE-ICE AND ENGINE SYSTEM
CHECKS TO PERFORM AFTER A
PROPELLER LIGHTNING STRIKE.
(1) General
In the event of a propeller lightning strike, an inspection
is required before further flight. It may be permissible to
operate a propeller for an additional ten (10) hours of
operation if the propeller is not severely damaged and
meets the requirements in Procedure for Temporary
Operation in this section. Regardless of the outcome
of the initial inspection, the propeller must eventually
be removed from the aircraft, disassembled, evaluated,
and/or repaired by an appropriately licensed propeller
repair facility.
(2) Procedure for Temporary Operation
If temporary additional operation is desired before
propeller removal and disassembly:
(a) Remove spinner dome and perform visual inspection
of propeller, spinner, and de-ice system for evidence
of significant damage that would require repair
before flight (such as broken de-ice wires or arcing
damage to propeller hub, blades, or blade clamps).
CAUTION: IF THE PROPELLER EXPERIENCES
A LIGHTNING STRIKE, THE
ALUMINUM BLADES MUST BE
WITHIN AIRWORTHY LIMITS FOR ANY
ADDITIONAL FLIGHT.
(b) If the only evident damage is minor arcing burns
to the blades, then operation for ten (10) hours is
acceptable before disassembly and inspection.
(c) Perform a functional check of the propeller de-ice
system (if installed) in accordance with aircraft
maintenance manual procedures.

Page 5-30
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

(d) Regardless of the degree of damage, make a log

book entry to document the lightning strike.
(e) The propeller must be removed from the aircraft,
disassembled, evaluated, and/or repaired by an
appropriately licensed propeller repair facility for
flight beyond the temporary operation limits granted
above.
D. Foreign Object Strike
(1) General
(a) A foreign object strike can include a broad spectrum
of damage, from a minor stone nick to severe
ground impact damage. A conservative approach in
evaluating the damage is required because there
may be hidden damage that is not readily apparent
during an on-wing, visual inspection.
(b) A foreign object strike is defined as:
1 Any incident, whether or not the engine is
operating, that requires repair to the propeller
other than minor dressing of the blades.
Examples of foreign object strike include
situations where an aircraft is stationary and the
landing gear collapses, causing one or more
blades to be significantly damaged, or where
a hangar door (or other object) strikes the
propeller blade. These cases should be handled
as foreign object strikes because of potentially
severe side loading on the propeller hub,
clamps, blades and retention bearings.
2 Any incident during engine operation in which
the propeller impacts a solid object that causes
a drop in revolutions per minute (RPM) and
also requires structural repair of the propeller
(incidents requiring only paint touch-up are
not included). This is not restricted to propeller
strikes against the ground.
3 A sudden RPM drop while impacting water,
tall grass, or similar yielding medium, where
propeller blade damage is not normally incurred.

Page 5-31
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

(2) Procedure
(a) In the event of a foreign object strike/ground strike,
an inspection is required before further flight. If the
inspection reveals one or more of the following
indications, the propeller must be removed from the
aircraft, disassembled and overhauled in accordance
with the applicable propeller and blade maintenance
manuals.
1 A blade rotated in the clamp
2 Any noticeable or suspected damage to the
pitch change mechanism
3 A bent blade (out of track or angle).
4 Any diameter reduction
5 Blade damage
6 A bent, cracked, or failed engine shaft
7 Vibration during operation
(b) Nicks, gouges, and scratches on blade surfaces or
the leading and trailing edges must be removed
before flight. Refer to the Blade Repairs section in
the Maintenance Practices chapter of this manual.
(c) Engine mounted components such as governors,
pumps, etc. may be damaged by a foreign object
strike/ground strike, especially if the strike resulted
in a sudden stoppage of the engine. These
components should be inspected, repaired, or
overhauled as recommended by the applicable
component maintenance manual.
(d) Make a log book entry to document the foreign
object strike/ground strike incident and any
corrective action(s) taken.

Page 5-32
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

E. Fire Damage or Heat Damage

WARNING: HUBS AND CLAMPS ARE
MANUFACTURED FROM HEAT TREATED
FORGINGS AND ARE SHOT PEENED.
BLADES ARE MANUFACTURED FROM
HEAT TREATED FORGINGS AND
ARE COMPRESSIVELY ROLLED AND
SOMETIMES SHOT PEENED. EXPOSURE
TO HIGH TEMPERATURES CAN
DESTROY THE FATIGUE RESISTANCE
BENEFITS OBTAINED FROM THESE
PROCESSES.
On rare occasions propellers may be exposed to fire or heat
damage, such as an engine or hangar fire. In the event of
such an incident, an inspection by an appropriately licensed
propeller repair facility is required before further flight.

Page 5-33
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner’s Manual
139

7. Long Term Storage

CAUTION: INSTRUCTIONS AND PROCEDURES IN THIS
SECTION MAY INVOLVE CRITICAL PARTS.
REFER TO THE INTRODUCTION CHAPTER
OF THIS MANUAL FOR INFORMATION ABOUT
PROPELLER CRITICAL PARTS. REFER TO
THE ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL MANUAL(S)
FOR THE IDENTIFICATION OF SPECIFIC
PROPELLER CRITICAL PARTS.
Parts shipped from the Hartzell Propeller Inc. factory are not
shipped or packaged in a container that is designed for long term
storage.
Long term storage procedures may be obtained by contacting
a Hartzell Propeller Inc. distributor, or the Hartzell Propeller Inc.
factory via the Product Support number listed in the Introduction
chapter of this manual. Storage information is also detailed in
Hartzell Propeller Inc. Manual 202A (61-01-02).
Information regarding the return of a propeller assembly to
service after long term storage may be obtained by contacting
a Hartzell Propeller Inc. distributor or RRF, or the Hartzell
Propeller Inc. factory via the product support number listed in
the Introduction chapter of this manual. This information is also
detailed in Hartzell Propeller Inc. Manual 202A (61-01-02).

Page 5-34
INSPECTION AND CHECK 61-00-39 Rev. 11 Jul/12
 Propeller Owner's Manual
139

MAINTENANCE PRACTICES - CONTENTS

1. Cleaning......................................................................................6-3
A. General Cleaning...................................................................6-3
B. Spinner Cleaning and Polishing.............................................6-5
2. Lubrication...................................................................................6-5
A. Lubrication Intervals...............................................................6-5
B. Lubrication Procedure............................................................6-6
C. Approved Lubricants..............................................................6-8
3. Carbon Block Assemblies...........................................................6-9
A. Inspection..............................................................................6-9
B. Replacement of A-3026 Carbon Block Unit
in the A-3044 Carbon Block Assembly...................................6-9
C. Installation of the A-3044 Carbon Block Assembly..............6-10
4. Blade Repairs............................................................................ 6-11
A. Repair of Nicks and Gouges................................................6-13
B. Repair of Bent Blades..........................................................6-15
5. Painting After Repair.................................................................6-16
A. Painting of Aluminum Blades...............................................6-18
6. Dynamic Balance......................................................................6-20
A. Overview..............................................................................6-20
B. Inspection Procedures Before Balancing.............................6-21
C. Modifying Spinner Bulkhead to Accommodate Dynamic
Balance Weights..................................................................6-21
D. Placement of Balance Weights for Dynamic Balance..........6-22
7. Propeller Ice Protection Systems..............................................6-23
A. Electric De-ice System.........................................................6-23
B. Anti-ice System....................................................................6-23

Page 6-1
MAINTENANCE PRACTICES 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

MAINTENANCE PRACTICES - FIGURES

Grease Fitting.................................................. Figure 6-1...............6-4

Lubrication Label............................................. Figure 6-2...............6-7
Repair Limitations............................................ Figure 6-3.............6-12

MAINTENANCE PRACTICES - TABLES

Approved Touch-up Paints............................... Table 6-1..............6-17

Page 6-2
MAINTENANCE PRACTICES 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

1. Cleaning
CAUTION 1: INSTRUCTIONS AND PROCEDURES IN THIS
SECTION MAY INVOLVE CRITICAL PARTS.
REFER TO THE INTRODUCTION CHAPTER
OF THIS MANUAL FOR INFORMATION ABOUT
PROPELLER CRITICAL PARTS. REFER TO
THE ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL MANUAL(S)
FOR THE IDENTIFICATION OF SPECIFIC
PROPELLER CRITICAL PARTS.

CAUTION 2: DO NOT USE PRESSURE WASHING

EQUIPMENT TO CLEAN THE PROPELLER
OR CONTROL COMPONENTS. PRESSURE
WASHING CAN FORCE WATER AND/OR
CLEANING SOLVENTS PAST SEALS, AND
CAN LEAD TO INTERNAL CORROSION OF
PROPELLER COMPONENTS.
A. General Cleaning
CAUTION 1: WHEN CLEANING THE PROPELLER,
DO NOT ALLOW SOAP OR SOLVENT
SOLUTIONS TO RUN OR SPLASH INTO
THE HUB AREA.

CAUTION 2: DO NOT CLEAN PROPELLER WITH

CAUSTIC OR ACIDIC SOAP SOLUTIONS.
IRREPARABLE CORROSION OF
PROPELLER COMPONENTS MAY
OCCUR.
(1) Wash propeller with a noncorrosive soap solution.
CAUTION: DO NOT USE ANY SOLVENT DURING
CLEANING THAT COULD SOFTEN
OR DESTROY THE BOND BETWEEN
CHEMICALLY ­ATTACHED PARTS.
(2) To remove grease or oil from propeller surfaces, apply
Stoddard Solvent or equivalent to a clean cloth and wipe
the part clean.
(3) Thoroughly rinse with water and allow to dry.

Page 6-3
MAINTENANCE PRACTICES 61-00-39 Rev. 11 Jul/12
 Propeller Owner's Manual
D-1490.PLT 139

(ONE IN EACH CLAMP HALF)

GREASE FITTING

Grease Fitting
Figure 6-1

Page 6-4
MAINTENANCE PRACTICES 61-00-39 Rev. 6 Mar/01
 Propeller Owner's Manual
139

B. Spinner Cleaning and Polishing

(1) Clean the spinner using the General Cleaning
procedures in this section.
(2) Polish the dome (if required) with an automotive type
aluminum polish.
2. Lubrication
CAUTION: INSTRUCTIONS AND PROCEDURES IN THIS
SECTION MAY INVOLVE CRITICAL PARTS.
REFER TO THE INTRODUCTION CHAPTER
OF THIS MANUAL FOR INFORMATION ABOUT
PROPELLER CRITICAL PARTS. REFER TO
THE ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL MANUAL(S)
FOR THE IDENTIFICATION OF SPECIFIC
PROPELLER CRITICAL PARTS.
A. Lubrication Intervals
(1) The propeller is to be lubricated at intervals not to
exceed 200 hours or at 12 calendar months, whichever
occurs first.
NOTE 1: If annual operation is significantly less than
100 hours, calendar lubrication intervals
should be reduced to six months.
NOTE 2: If the aircraft is operated or stored under
adverse atmospheric conditions, e.g., high
humidity, salt air, calendar lubrication intervals
should be reduced to 100 hours or six months.
NOTE 3: If the propeller is operated on a seaplane, the
lubrication interval should be reduced to 100
hours or six months.
NOTE 4: If the propeller is leaking grease, the
lubrication interval should be reduced to 100
hours until the grease leak issue is resolved.
(2) Owners of high use aircraft may wish to extend their
lubrication intervals. Lubrication interval may be
gradually extended after evaluation of previous propeller
overhauls, with regard to bearing wear and internal
corrosion.

Page 6-5
MAINTENANCE PRACTICES 61-00-39 Rev. 11 Jul/12
 Propeller Owner's Manual
139

(3) New or newly overhauled propellers should be lubricated

after the first one or two hours of operation, because
centrifugal loads will pack and redistribute grease.
NOTE: Purchasers of new aircraft should check
the propeller logbook to verify whether the
propeller was lubricated by the manufacturer
during flight testing. If not, the propeller should
be serviced at earliest convenience.
B. Lubrication Procedure
CAUTION: FOLLOW LUBRICATION PROCEDURES
CORRECTLY TO MAINTAIN AN
ACCURATE BALANCE OF THE
PROPELLER ASSEMBLY.
(1) Remove the propeller spinner.
(2) Refer to Figure 6-1. Each blade clamp has two
lubrication fittings. Remove both lubrication fitting caps
and one of the lubrication fittings from each blade clamp.
(3) Use a piece of safety wire to loosen any blockage
or hardened grease in the threaded holes where the
lubrication fitting was removed.
WARNING: WHEN MIXING AEROSHELL GREASES 5
AND 6, AEROSHELL GREASE 5 MUST BE
INDICATED ON THE LABEL (HARTZELL
PROPELLER INC. P/N A-3594) AND THE
AIRCRAFT MUST BE PLACARDED TO
INDICATE THAT FLIGHT IS PROHIBITED
IF THE OUTSIDE AIR TEMPERATURE IS
LESS THAN -40°F (-40°C).

CAUTION: USE HARTZELL PROPELLER INC.

PROPELLER APPROVED GREASE ONLY.
EXCEPT IN THE CASE OF AEROSHELL
GREASES 5 AND 6, DO NOT MIX
DIFFERENT SPECIFICATIONS AND/OR
BRANDS OF GREASE.
(4) Aeroshell greases 5 and 6 both have a mineral oil base
and have the same thickening agent; therefore, mixing of
these two greases is acceptable in Hartzell Propeller Inc.
propellers.
Page 6-6
MAINTENANCE PRACTICES 61-00-39 Rev. 11 Jul/12
 Propeller Owner's Manual
139

(5) A label (Hartzell Propeller Inc. P/N A-3494) is normally

applied to the propeller to indicate the type of grease
previously used (Figure 6-2).
(a) This grease type should be used during re-
lubrication unless the propeller has been
disassembled and the old grease removed.
(b) Purging of old grease through lubrication fittings is
only about 30 percent effective.
(c) To completely replace one grease with another, the
propeller must be disassembled in accordance with
the applicable overhaul manual.
CAUTION 1: IF A PNEUMATIC GREASE GUN IS USED,
EXTRA CARE MUST BE TAKEN TO AVOID
EXCESSIVE PRESSURE BUILDUP.

CAUTION 2: GREASE MUST BE APPLIED TO ALL

BLADES OF A PROPELLER ASSEMBLY AT
THE TIME OF LUBRICATION.
(6) Pump grease into the blade clamp grease fitting until
grease emerges from the hole of the removed lubrication
fitting.
NOTE: Lubrication is complete when grease emerges
in a steady flow with no air pockets or
moisture, and has the color and texture of the
new grease.

A-3594

Lubrication Label
Figure 6-2

Page 6-7
MAINTENANCE PRACTICES 61-00-39 Rev. 11 Jul/12
 Propeller Owner's Manual
139

(7) Repeat step 2.B.(4) for each blade clamp assembly.

(8) Reinstall the removed lubrication fitting on each clamp.
(9) Tighten the lubrication fittings until snug.
(a) Make sure the ball of each lubrication fitting is
properly seated.
(10)Reinstall a lubrication cap on each lubrication fitting.
C. Approved Lubricants
(1) The following lubricants are approved for use in Hartzell
Propeller Inc. propellers:
Aeroshell 6 - Recommended all purpose grease.
Used in most new production propellers
since 1989. Higher leakage/oil
separation than Aeroshell 5 at higher
temperatures.
Aeroshell 5 - Good high temperature qualities, very
little oil separation or leakage. Cannot
be used in temperatures colder than
40°F (-40°C). Aircraft serviced with this
grease must be placarded to indicate
that flight is prohibited if the outside air
temperature is less than -40°F (-40°C).
Aeroshell 7 - Good low temperature grease, but high
leakage/oil separation at higher
temperatures. This grease has been
associated with sporadic problems
involving seal swelling.
Aeroshell 22 - Qualities similar to Aeroshell 7.
Royco 22CF - Not widely used. Qualities similar to
Aeroshell 22.
(2) A label indicating the type of grease used for previous
lubrication (if used) is installed on the propeller piston or
on the blade clamp. If the propeller must be lubricated
with a different type of grease, the propeller must
be disassembled and cleaned of old grease before
relubricating.

Page 6-8
MAINTENANCE PRACTICES 61-00-39 Rev. 11 Jul/12
 Propeller Owner's Manual
139

3. Carbon Block Assemblies

CAUTION: INSTRUCTIONS AND PROCEDURES IN THIS
SECTION MAY INVOLVE CRITICAL PARTS.
REFER TO THE INTRODUCTION CHAPTER
OF THIS MANUAL FOR INFORMATION ABOUT
PROPELLER CRITICAL PARTS. REFER TO
THE ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL MANUAL(S)
FOR THE IDENTIFICATION OF SPECIFIC
PROPELLER CRITICAL PARTS.
A. Inspection
The clearance between the yoke pin and the corresponding
linkage (beta lever bushing) can become too close due
to a buildup of plating and foreign particles between the
two pieces. This can cause a binding action, resulting in
excessive wear to the carbon block, beta ring, and beta
linkage.
(1) Inspect the beta lever and carbon block interface for free
movement. If there is binding, do the following:
(a) Disconnect the beta linkage and remove the carbon
block assemblies from the beta ring.
(b) Using an abrasive pad, lightly polish the yoke pin to
provide adequate clearance and eliminate binding.
(c) Reinstall the carbon block assembly into the beta
ring.
(d) Install, adjust and safety the beta linkage per the
airframe manufacturer's instructions.
B. Replacement of A-3026 Carbon Block Unit in the A-3044
Carbon Block Assembly
Replace an A-3026 carbon block unit if the side clearance
between the beta ring and carbon block exceeds 0.010 inch
(0.25 mm).
(1) Remove the cotter pin from the end of the clevis pin.
(2) Slide the pin from the assembly and remove and discard
the carbon block unit.
(3) Inspect the yoke for wear or cracks. Replace the yoke if
necessary.

Page 6-9
MAINTENANCE PRACTICES 61-00-39 Rev. 13 Jun/15
 Propeller Owner's Manual
139

(4) Install a new carbon block unit and slide a new clevis pin
into place.
(5) Secure the clevis pin with a T-head cotter pin
(Figure 3-7).
(6) Refit the carbon block (Figure 3-6).
(a) Establish the required clearance by sanding the
sides of the carbon block as needed.
C. Installation of the A-3044 Carbon Block Assembly
Refer to Installation and Removal Chapter of this manual for
installation instructions.

Page 6-10
MAINTENANCE PRACTICES 61-00-39 Rev. 11 Jul/12
 Propeller Owner's Manual
139

4. Blade Repairs
WARNING: ALL NICKS, GOUGES, OR SCRATCHES OF
ANY SIZE CAN CREATE A STRESS RISER
THAT COULD POTENTIALLY LEAD TO BLADE
CRACKING. ALL DAMAGE SHOULD BE
VISUALLY EXAMINED CAREFULLY BEFORE
FLIGHT FOR THE PRESENCE OF CRACKS
OR OTHER ABNORMALITIES.

CAUTION 1: INSTRUCTIONS AND PROCEDURES IN

THIS SECTION MAY INVOLVE PROPELLER
CRITICAL PARTS. REFER TO THE
INTRODUCTION CHAPTER OF THIS
MANUAL FOR INFORMATION ABOUT
PROPELLER CRITICAL PARTS. REFER TO
THE ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL MANUAL(S)
FOR THE IDENTIFICATION OF SPECIFIC
PROPELLER CRITICAL PARTS.

CAUTION 2: BLADES THAT HAVE BEEN PREVIOUSLY

REPAIRED OR OVERHAULED MAY HAVE
BEEN DIMENSIONALLY REDUCED. BEFORE
REPAIRING SIGNIFICANT DAMAGE OR
MAKING REPAIRS ON BLADES THAT ARE
APPROACHING SERVICEABLE LIMITS,
CONTACT AN APPROPRIATELY LICENSED
PROPELLER REPAIR FACILITY OR THE
HARTZELL PROPELLER INC. PRODUCT
SUPPORT DEPARTMENT FOR BLADE
DIMENSIONAL LIMITS.
Nicks, gouges, and scratches on blade surfaces or on the
leading or trailing edges of the blade, greater than 0.031
inch (0.79 mm) wide or deep, must be removed before flight.
Field repair of small nicks and scratches may be performed
by qualified personnel in accordance with FAA Advisory
Circular 43.13-1B, as well as the procedures specified below.
Normal blade lead edge erosion (sand-blasted appearance) is
acceptable, and does not require removal before further flight.

Page 6-11
MAINTENANCE PRACTICES 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

APS6157A

Example 1

LOOKING AT
LEADING EDGE

Example 2 Example 3
LEADING EDGE
2.50 inch (6.35 cm)
2.50 inch (6.35 cm) = D x 20
= D x 10 0.125 inch (3.13 mm) deep
0.25 inch (6.3 mm) deep

LOCAL LOCAL
REPAIR REPAIR

To determine amount of rework needed, use the following formula:

On the leading and trailing edge of the blade, measure the depth of the damage,
and multiply this number x 10 (see Example 2, above). Rework the area surrounding
the damage 10 times the depth of the damage.

On the face and camber of the blade, measure the depth of the damage, and
multiply this number x 20 (see Example 3, above). Rework the area surrounding the
damage 20 times the depth of the damage.

Repair Limitations
Figure 6-3

Page 6-12
MAINTENANCE PRACTICES 61-00-39 Rev. 11 Jul/12
 Propeller Owner's Manual
139

A. Repair of Nicks and Gouges

(1) Local repairs may be made using files, electrical or air
powered equipment. Emery cloth, Scotch Brite®, and
crocus cloth are to be used for final finishing. Refer to
Figure 6-3.
CAUTION 1: REWORK THAT INVOLVES COLD
WORKING THE METAL, RESULTING
IN CONCEALMENT OF A DAMAGED
AREA, IS NOT PERMITTED. A STRESS
CONCENTRATION MAY EXIST, WHICH
CAN RESULT IN A BLADE FAILURE.

CAUTION 2: SHOT PEENED BLADES ARE IDENTIFIED

WITH AN "S" FOLLOWING THE BLADE
MODEL NUMBER, AS DESCRIBED IN THE
DESCRIPTION AND OPERATION CHAPTER
OF THIS MANUAL. BLADES THAT HAVE
DAMAGE IN THE SHOT PEENED AREAS IN
EXCESS OF 0.015 INCH (0.38 mm) DEEP
ON THE FACE OR CAMBER OR
0.250 INCH (6.35 MM) ON THE LEADING
OR TRAILING EDGES MUST BE
REMOVED FROM SERVICE, AND THE
REWORKED AREA SHOT PEENED BEFORE
FURTHER FLIGHT. SHOT PEENING
OF AN ALUMINUM BLADE MUST BE
ACCOMPLISHED BY AN FAA APPROVED
REPAIR FACILITY IN ACCORDANCE WITH
HARTZELL PROPELLER INC. ALUMINUM
BLADE MANUAL 133C (61-13-33).
(2) Repairs to the leading or trailing edge are to be
accomplished by removing material from the bottom of
the damaged area. Remove material from this point
out to both sides of the damage, providing a smooth,
blended depression which maintains the original airfoil
general shape.
(3) Repairs to the blade face or camber should be made
in the same manner as above. Repairs that form a
continuous line across the blade section (chordwise) are
unacceptable.

Page 6-13
MAINTENANCE PRACTICES 61-00-39 Rev. 11 Jul/12
 Propeller Owner's Manual
139

(4) The area of repair should be determined as follows:

Leading and trailing edge damage: Depth of nick x 10.
Face and camber: Depth of nick x 20. Refer to
Figure 6-3.
NOTE: Leading edge includes the first 10 percent
of chord from the leading edge. The trailing
edge consists of the last 20 percent of chord
adjacent to the trailing edge.
(5) After filing or sanding of the damaged area, the area
must then be polished with emery cloth, Scotch Brite®,
and finally with crocus cloth to remove any traces of
filing.
(6) Inspect the repaired area with a 10X magnifying glass.
Make sure that no indication of the damage, file marks,
or coarse surface finish remain.
(7) If inspections show any remaining blade damage, repeat
steps A.(5) and A.(6) of this chapter until no damage
remains. Dye penetrant inspection is recommended in
accordance with the Hartzell Standard Practices Manual
202A, (61-01-02) .
(8) Treat the repaired area to prevent corrosion. Properly
apply chemical conversion coating and approved paint to
the repaired area before returning the blade to service.
Refer to Painting After Repair in this section.

Page 6-14
MAINTENANCE PRACTICES 61-00-39 Rev. 11 Jul/12
 Propeller Owner's Manual
139

B. Repair of Bent Blades

CAUTION: DO NOT ATTEMPT TO "PRE-
STRAIGHTEN" A BLADE BEFORE
DELIVERY TO AN APPROPRIATELY
LICENSED PROPELLER REPAIR
FACILITY. THIS WILL CAUSE THE BLADE
TO BE SCRAPPED BY THE REPAIR
FACILITY.
(1) Repair of a bent blade or blades is considered a major
repair. This type of repair must be accomplished by an
appropriately licensed propeller repair facility, and only
within approved guidelines.

Page 6-15
MAINTENANCE PRACTICES 61-00-39 Rev. 11 Jul/12
 Propeller Owner's Manual
139

5. Painting After Repair

CAUTION: INSTRUCTIONS AND PROCEDURES IN THIS
SECTION MAY INVOLVE CRITICAL PARTS.
REFER TO THE INTRODUCTION CHAPTER
OF THIS MANUAL FOR INFORMATION ABOUT
PROPELLER CRITICAL PARTS. REFER TO
THE ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL MANUAL(S)
FOR THE IDENTIFICATION OF SPECIFIC
PROPELLER CRITICAL PARTS.
Propeller blades are painted with a durable specialized coating
that is resistant to abrasion. If this coating becomes eroded, it is
necessary to repaint the blades to provide proper corrosion and
erosion protection. Painting should be performed by qualified
personnel at an appropriately licensed propeller repair facility
in accordance with Hartzell Propeller Inc. Standard Practices
Manual 202A (61-01-02).
It is permissible to perform a blade touch-up with aerosol paint in
accordance with the procedures in Painting of Aluminum Blades
in this chapter.
Refer to Table 6-1 for paints approved for blade touch-up.
The paint manufacturers may be contacted via the information
below:
Tempo Products Co. Sherwin Williams Co.
A plasti-kote Company 2390 Arbor Boulevard
1000 Lake Road Dayton, Ohio
Medina, OH 44256 Tel: 937.298.8691
Tel: 800.321.6300 Fax: 937.298.3820
Fax: 216.349.4241 Cage Code: 0W199
Cage Code: 07708

Page 6-16
MAINTENANCE PRACTICES 61-00-39 Rev. 11 Jul/12
 Propeller Owner's Manual
139

Vendor Color Vendor Hartzell

P/N Propeller
Inc. P/N
Tempo Epoxy Black A-150 A-6741-145-2

Tempo Epoxy Gray A-151 A-6741-146-2

Tempo Epoxy White (tip stripe) A-152 A-6741-147-2

Tempo Epoxy Red (tip stripe) A-153 A-6741-149-2

Tempo Epoxy Yellow (tip stripe) A-154 A-6741-150-2

Sherwin-Williams Black F75KXB9958-4311 A-6741-145-1

Sherwin-Williams Gray F75KXA10445-4311 A-6741-146-1

Sherwin-Williams White (tip stripe) F75KXW10309-4311 A-6741-147-1

Sherwin-Williams Gray Metallic F75KXM9754-4311 A-6741-148-1

Sherwin-Williams Red (tip stripe) F75KXR12320-4311 A-6741-149-1

Sherwin-Williams Yellow (tip stripe) F75KXY11841-4311 A-6741-150-1

Sherwin-Williams Silver F75KXS13564-4311 A-6741-190-1

Sherwin-Williams Bright Red F63TXR16285-4311 A-6741-200-5

Sherwin-Williams Bright Yellow F63TXY16286-4311 A-6741-201-5

Sherwin-Williams Bright Silver F63TXS16768-4311 A-6741-203-5

Sherwin-Williams Prop Gold F63TXS17221-4311 A-6741-204-5

Approved Touch-up Paints

Table 6-1

Page 6-17
MAINTENANCE PRACTICES 61-00-39 Rev. 11 Jul/12
 Propeller Owner's Manual
139

A. Painting of Aluminum Blades

WARNING: CLEANING AGENTS (ACETONE, #700
LACQUER THINNER, AND MEK), ARE
FLAMMABLE AND TOXIC TO THE SKIN,
EYES, AND RESPIRATORY TRACT. SKIN
AND EYE PROTECTION ARE REQUIRED.
AVOID PROLONGED CONTACT. USE IN
WELL VENTILATED AREA.

CAUTION: ANY REFINISHING PROCEDURE

CAN ALTER PROPELLER BALANCE.
PROPELLERS THAT ARE OUT OF
BALANCE MAY EXPERIENCE EXCESSIVE
VIBRATIONS WHILE IN OPERATION.
(1) Using acetone, #700 lacquer thinner, or MEK, wipe the
surface of the blade to remove any contaminants.
(2) Feather the existing coatings away from the eroded or
repaired area with 120 to 180 grit sandpaper.
NOTE: Paint erosion is typically very similar on all
blades in a propeller assembly. If one blade has
more extensive paint erosion, e.g., in the tip
area, all the blades should be sanded in the tip
area to replicate the repair of the most severely
damaged blade tip. This practice is essential in
maintaining balance after refinishing.
(3) Use acetone, #700 lacquer thinner or MEK to wipe the
surface of the blade. Allow solvent to evaporate.
(4) Before refinishing the blades, apply an approved
corrosion preventive coating to the bare aluminum
surface. Oakite 31, Chromicote L-25, or Alodine 1201
are approved chemical conversion coatings. Apply these
coatings in accordance with the directions provided by
the product manufacturer.
(5) Apply masking material for the de-ice boot and tip
stripes, as needed.

Page 6-18
MAINTENANCE PRACTICES 61-00-39 Rev. 11 Jul/12
 Propeller Owner's Manual
139

WARNING: FINISH COATINGS ARE FLAMMABLE

AND TOXIC TO THE SKIN, EYES, AND
RESPIRATORY TRACT. SKIN AND EYE
PROTECTION ARE REQUIRED. AVOID
PROLONGED CONTACT. USE IN WELL
VENTILATED AREA.

CAUTION: APPLY ENOUGH FINISH COATING ONLY

TO UNIFORMLY COVER THE REPAIR/
EROSION. AVOID EXCESSIVE PAINT
BUILDUP ALONG THE TRAILING EDGE
TO AVOID CHANGING BLADE PROFILE.
(6) Apply sufficient finish coating to achieve 2 to 4 mils
thickness when dry. Re-coat before 30 minutes, or after
48 hours. If the paint is permitted to dry longer than four
(4) hours, it must be lightly sanded before another coat
is applied.
(7) Remove the masking from the tip stripes and re-mask to
allow for the tip stripe refinishing if required.
(8) Apply sufficient tip stripe coating to achieve 2 to 4 mils
thickness when dry. Re-coat before 30 minutes, or after
48 hours. If the paint is permitted to dry longer than four
(4) hours, it must be lightly sanded before another coat
is applied.
(9) Remove tape immediately from the de-ice boot and tip
stripes, if required.
(10)Optionally, perform dynamic balancing in accordance
with the procedures and limitations specified in the
Dynamic Balance section of this chapter.

Page 6-19
MAINTENANCE PRACTICES 61-00-39 Rev. 11 Jul/12
 Propeller Owner's Manual
139

6. Dynamic Balance
CAUTION: INSTRUCTIONS AND PROCEDURES IN THIS
SECTION MAY INVOLVE CRITICAL PARTS.
REFER TO THE INTRODUCTION CHAPTER
OF THIS MANUAL FOR INFORMATION ABOUT
PROPELLER CRITICAL PARTS. REFER TO
THE ILLUSTRATED PARTS LIST CHAPTER
OF THE APPLICABLE OVERHAUL MANUAL(S)
FOR THE IDENTIFICATION OF SPECIFIC
PROPELLER CRITICAL PARTS.
A. Overview
WARNING: WHEN USING REFLECTIVE TAPE FOR
DYNAMIC BALANCING, DO NOT APPLY
THE TAPE ON EXPOSED BARE METAL OF
A BLADE. THIS WILL ALLOW MOISTURE TO
COLLECT UNDER THE TAPE AND CAUSE
CORROSION THAT CAN PERMANENTLY
DAMAGE THE BLADE. REFLECTIVE TAPE
MUST BE REMOVED AFTER DYNAMIC
BALANCING IS COMPLETED.
NOTE: Dynamic balance is recommended to reduce
vibrations that may be caused by a rotating
system (propeller and engine) imbalance. Dynamic
balancing can help prolong the life of the propeller,
engine, airframe, and avionics.
(1) Dynamic balance is accomplished by using an accurate
means of measuring the amount and location of the
dynamic imbalance.
(2) The maximum permitted imbalance reading is 0.2 IPS.
(3) The number of balance weights installed must not
exceed the limits specified in this chapter.
(4) Follow the dynamic balance equipment manufacturer’s
instructions for dynamic balance in addition to the
specifications of this section.
NOTE: Some engine manufacturer's instructions also
contain information on dynamic balance limits.

Page 6-20
MAINTENANCE PRACTICES 61-00-39 Rev. 11 Jul/12
 Propeller Owner's Manual
139

B. Inspection Procedures Before Balancing

(1) Visually inspect the propeller assembly before dynamic
balancing.
NOTE: The first run-up of a new or overhauled
propeller assembly may leave a small amount
of grease on the blades and inner surface of
the spinner dome.
(a) Use a Stoddard solvent (or equivalent) to completely
remove any grease on the blades or inner surface of
the spinner dome.
(b) Visually check each propeller blade assembly for
evidence of grease leakage.
(c) Visually inspect the inner surface of the spinner
dome for evidence of grease leakage.
(2) If there is no evidence of grease leakage, lubricate the
propeller in accordance with the Maintenance Practices
chapter in this manual. If grease leakage is evident,
determine the location of the leak and correct before re-
lubricating the propeller and dynamic balancing.
(3) Before dynamic balancing, record the number and
location of all balance weights.
C. Modifying Spinner Bulkhead to Accommodate Dynamic
Balance Weights
CAUTION: ALL HOLE/BALANCE WEIGHT
LOCATIONS MUST TAKE INTO
CONSIDERATION, AND MUST AVOID, ANY
POSSIBILITY OF INTERFERING WITH
THE ADJACENT AIRFRAME, DE-ICE AND
ENGINE COMPONENTS.
(1) It is recommended that the placement of balance
weights be in a radial location on aluminum spinner
bulkheads that have not been previously drilled.
(2) The radial location should be outboard of the de-ice slip
ring or bulkhead doubler and inboard of the bend where
the bulkhead creates the flange to attach the spinner
dome.

Page 6-21
MAINTENANCE PRACTICES 61-00-39 Rev. 11 Jul/12
 Propeller Owner's Manual
139

(3) Twelve equally spaced locations for weight attachment

are recommended.
(4) Install nut plates (10-32 thread) of the type used to
attach the spinner dome, will allow convenient balance
weight attachment on the engine side of the bulkhead.
(5) Alternatively, drilling holes for use with the AN3-( ) type
bolts with self-locking nuts is acceptable.
NOTE: Chadwick-Helmuth Manual AW-9511-2, “The
Smooth Propeller”, specifies several generic
bulkhead rework procedures. These are
acceptable providing they comply with the
conditions specified herein.
D. Placement of Balance Weights for Dynamic Balance
(1) The preferred method of attachment of dynamic balance
weights is to add the weights to the spinner bulkhead.
NOTE: Many spinner bulkheads have factory installed
self-locking nut plates provided for this
purpose.
(2) If the location of static balance weights has not been
altered, subsequent removal of the dynamic balance
weights will return the propeller to its original static
balance condition.
(3) Use only stainless or plated steel washers as dynamic
balance weights on the spinner bulkhead.
(4) Do not exceed a maximum weight per location of 0.9 oz.
(25.5 g).
NOTE: This is approximately equal to six AN970 style
washers (0.188 inch ID, 0.875 inch OD, 0.063
inch thickness) (4.78 mm ID, 22.23 mm OD,
1.60 mm thickness).
(5) Install weights using aircraft quality #10-32 or AN-3( )
type screws or bolts.

Page 6-22
MAINTENANCE PRACTICES 61-00-39 Rev. 11 Jul/12
 Propeller Owner's Manual
139

(6) Balance weight screws attached to the spinner bulkhead

must protrude through the self-locking nuts or nut
plates a minimum of one thread and a maximum of four
threads.
NOTE: It may be necessary to alter the number and/
or location of static balance weights in order to
achieve dynamic balance.
(7) If reflective tape is used for dynamic balancing, remove
the tape immediately upon completion. Tape that
remains on the blade will permit moisture to collect under
the tape and cause corrosion that can permanently
damage the blade.
(8) Record the number and location of dynamic balance
weights and static balance weights, if they have been
reconfigured, in the logbook.
7. Propeller Ice Protection Systems
A. Electric De-ice System
(1) Consult the Pilot Operating Handbook (including all
supplements) regarding flight into conditions of known
icing. The aircraft may not be certificated for flight in
known icing conditions, even though propeller de-ice
equipment is installed.
(2) Refer to the Anti-ice and De-ice Systems chapter of this
manual for functional tests of the de-ice system.
B. Anti-ice System
(1) Consult the Pilot Operating Handbook (including all
supplements) regarding flight into conditions of known
icing. The aircraft may not be certificated for flight in
known icing conditions, even though propeller anti-ice
equipment is installed.
(2) Refer to the Anti-ice and De-ice Systems chapter of this
manual for functional tests of the anti-ice system.

Page 6-23
MAINTENANCE PRACTICES 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

(This page is intentionally blank.)

Page 6-24
MAINTENANCE PRACTICES 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

ANTI-ICE AND DE-ICE SYSTEMS - CONTENTS

1. Introduction.................................................................................7-3
A. Propeller De-Ice System........................................................7-3
B. Propeller Anti-ice System.......................................................7-3
2. System Description.....................................................................7-4
A. De-ice System.......................................................................7-4
B. Anti-ice System......................................................................7-5
3. De-ice System Functional Tests..................................................7-5
4. Anti-ice System Functional Tests................................................7-5
5. De-ice and Anti-ice System Inspections......................................7-6
A. De-ice System Inspections....................................................7-6
B. Anti-ice System Inspections...................................................7-6
6. De-ice and Anti-ice System Troubleshooting..............................7-7
A. De-ice System Troubleshooting.............................................7-7
B. Anti-ice System Troubleshooting...........................................7-7

Page 7-1
ANTI-ICE AND DE-ICE SYSTEMS 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

(This page is intentionally blank.)

Page 7-2
ANTI-ICE AND DE-ICE SYSTEMS 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

1. Introduction
A. Propeller De-ice System
(1) A propeller de-ice system is a system that removes ice
after it forms on the propeller blades. A de-ice system
uses electrical heating elements to melt the ice layer
next to the blades, allowing the ice to be thrown from
the blade by centrifugal force. The de-ice system
timer controls the application of current to the blades,
alternately heating them and allowing them to cool.
(2) System components include a timer or cycling unit,
electrical slip ring(s), brush block assembly, and blade
mounted de-ice boots.
B. Propeller Anti-ice System
(1) A propeller anti-ice system is a system that prevents
formation of ice on propeller surfaces. An anti-ice system
dispenses a fluid that mixes with, and reduces the
freezing point of, moisture on the propeller blades. The
mixture may then flow off the blades before it forms ice.
(2) System components include a fluid tank, pump, slinger
ring, and blade mounted fluid anti-icing boots.

Page 7-3
ANTI-ICE AND DE-ICE SYSTEMS 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

2. System Description
A. De-ice System
NOTE: Because of the many differences in various
de-ice systems, the following description is general
in nature. Consult the airframe manufacturer’s
manual for a description of your specific de-ice
system and controls.
The de-ice system is controlled by the pilot via a cockpit
control switch. This switch applies power to the de-ice
system, which will operate as long as the switch is in the
ON position. Depending upon the system, another set of
cockpit controls may be available. One of these controls is
a mode selector, which allows the pilot to select two cycling
speeds, for heavy or light icing conditions. Some systems
on twin engine aircraft have a switch which provides a full
de-ice mode, which allows the pilot to de-ice both propellers
simultaneously. This switch may only be used for short
periods and is used when ice builds up on the propeller
before the system is turned on.
(1) An ammeter, which indicates current drawn by the
system, is normally located near the de-ice system
switches. This meter may indicate total system load, or a
separate meter may be supplied for each propeller.
(2) A timer, which is turned off and on by the cockpit control,
is used to sequence the de-ice system. This timer
turns the de-ice system on and off in proper sequence,
controlling the heating interval for each propeller blade
and ensuring even de-icing.
(3) A brush block mounted on the engine immediately
behind the propeller supplies power to the de-ice boot
on each propeller blade via a slip ring. The slip ring is
normally mounted on the spinner bulkhead.
(4) When the pilot places the de-ice system cockpit control
switch in the ON position, the system timer begins to
operate. As the timer sequences, power is delivered
to a power relay. The power relay delivers high current
through the brush block and slip ring to the de-ice boot.

Page 7-4
ANTI-ICE AND DE-ICE SYSTEMS 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

B. Anti-ice System
(1) The anti-ice system is controlled by the pilot via a cockpit
mounted rheostat. This rheostat operates a pump that
pumps anti-ice fluid from the tank at a controlled rate.
(2) The anti-ice fluid is delivered through a filter, a check
valve, and then through tubing to a slinger ring located
at the rear of the spinner bulkhead. The anti-ice fluid is
dispensed into the rotating slinger ring, which holds the
fluid in a curved channel by centrifugal force. The fluid
then flows out of the slinger ring through feed tubes
which are welded to the slinger ring, and then out onto
the blade anti-icing boots.
(3) The blade anti-icing boots are ridged rubber sheets that
are glued to the leading edge of the blades. The ridges
in the anti-icing boots direct the fluid out onto the blades
and permit for an even distribution of the anti-ice fluid
across the blades.
3. De-ice System Functional Tests
A. Functional tests of the de-ice system should be performed
in accordance with the following Hartzell Propeller Inc.
manuals, which are available on the Hartzell Propeller Inc.
website at www.hartzellprop.com.
(1) Hartzell Propeller Inc. Manual 181 (30-60-81) -
Propeller Ice Protection System Component
Maintenance Manual
(2) Hartzell Propeller Inc. Manual 182 (61-12-82) -
Propeller Electrical De-ice Boot Removal and Installation
Manual
4. Anti-ice System Functional Tests
A. Operational Checks of the anti-ice system should be
performed in accordance with the following Hartzell Propeller
Inc. manuals, which are available on the Hartzell Propeller
website at www.hartzellprop.com:
(1) Hartzell Propeller Inc. Manual 181 (30-60-81) - Propeller
Ice Protection System Component Maintenance Manual
(2) Hartzell Propeller Inc. Manual 183 (61-12-83) - Propeller
Anti-icing Boot Removal and Installation Manual

Page 7-5
ANTI-ICE AND DE-ICE SYSTEMS 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

5. De-ice and Anti-ice System Inspections

The inspections detailed below are made on a regular basis,
either before flight, during the 100 hour inspection, or if a
problem is noted. Possible corrections to problems discovered
during inspections, additional inspections, and limits are detailed
in the following Hartzell Propeller Inc. manuals, which are
available on the Hartzell Propeller Inc. website at
www.hartzellprop.com:
A. De-ice System Inspections
(1) Perform inspections in accordance with the following
Hartzell manuals, which are available on the Hartzell
Propeller Inc. website at www.hartzellprop.com:
(a) Hartzell Propeller Inc. Manual No. 181 (30-60-81) -
Propeller Ice Protection System Component
Maintenance Manual
(b) Hartzell Propeller Inc. Manual No. 182 (61-12-82) -
Propeller Electrical De-ice Boot Removal and
Installation Manual.
B. Anti-ice System Inspections
(1) Perform inspections in accordance with the following
Hartzell Propeller Inc. manuals, which are available on
the Hartzell Propeller website at www.hartzellprop.com:
(a) Hartzell Propeller Inc. Manual 181 (30-60-81)
- Propeller Ice Protection System Component
Maintenance Manual
(b) Hartzell Propeller Inc. Manual 183 (61-12-83) -
Propeller Anti-icing Boot Removal and Installation
Manual

Page 7-6
ANTI-ICE AND DE-ICE SYSTEMS 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

6. De-ice and Anti-ice System Troubleshooting

A. De-ice System Troubleshooting
(1) Perform troubleshooting in accordance with the following
Hartzell Propeller Inc. manuals, which are available on
the Hartzell Propeller Inc. website at
www.hartzellprop.com:
(a) Hartzell Propeller Inc. Manual 181 (30-60-81) -
Propeller Ice Protection System Component
Maintenance Manual
(b) Hartzell Propeller Inc. Manual 182 (61-12-82) -
Propeller Electrical De-ice Boot Removal and
Installation Manual
B. Anti-ice System Troubleshooting
(1) Perform troubleshooting in accordance with the following
Hartzell Propeller Inc. manuals, which are available on
the Hartzell Propeller Inc. website at
www.hartzellprop.com:
(a) Hartzell Propeller Inc. Manual 181 (30-60-81)
- Propeller Ice Protection System Component
Maintenance Manual
(b) Hartzell Propeller Inc. Manual 183 (61-12-83) -
Propeller Anti-icing Boot Removal and Installation
Manual

Page 7-7
ANTI-ICE AND DE-ICE SYSTEMS 61-00-39 Rev. 12 Mar/13
 Propeller Owner's Manual
139

(This page is intentionally blank.)

Page 7-8
ANTI-ICE AND DE-ICE SYSTEMS 61-00-39 Rev. 12 Mar/13
 Propeller Owner’s Manual
139

CONTENTS
1. Introduction.................................................................................8-3
2. Record Keeping..........................................................................8-3
A. Information to be Recorded...................................................8-3

Page 8-1
RECORDS 61-00-39 Rev. 5 Oct/99
 Propeller Owner’s Manual
139

(This page is intentionally blank.)

Page 8-2
RECORDS 61-00-39 Rev. 5 Oct/99
 Propeller Owner’s Manual
139

1. Introduction
Federal Aviation Regulations require that a record be kept of
any repairs, adjustments, maintenance, or required inspections
performed on a propeller or propeller system.
This chapter provides a method for maintaining these records. It
also provides a location for recording information that can aid the
service technician in maintaining the propeller system.
2. Record Keeping
A. Information to be Recorded
(1) Information which is required to be recorded is listed in
Part 43 of the U.S. Federal Aviation Regulations.
(2) The log book may also be used to record:
(a) Propeller position (on aircraft)
(b) Propeller model
(c) Propeller serial number
(d) Blade design number
(e) Blade serial numbers
(f) Spinner assembly part number
(g) Propeller pitch range
(h) Aircraft information (aircraft type, model, serial
number and registration number)

Page 8-3
RECORDS 61-00-39 Rev. 5 Oct/99
 Propeller Owner’s Manual
139

(This page is intentionally blank.)

Page 8-4
RECORDS 61-00-39 Rev. 5 Oct/99