Mechanical Engineering Department
POWER PLANT Assis- Professor Dr. Moayed Rzoki
[email protected]3. Steam Cycles
Lecture PP 2
Mechanical Engineering Department
Rankine cycle
Objectives :
•Apply thermodynamic principles to improve the Rankine cycle, via
additional components (feed water heaters, reheating, combined cycle)
•Understand heat transfer limitations
•Understand the process diagram of large scale steam power plant
Lecture PP 3
Mechanical Engineering Department
Ideal Rankine cycle
Four processes:
• 1 – 2 : Isentropic compression – Pump
• 2 – 3 : Constant Pressure (and
temperature) heat addition – Boiler
• 3 – 4 : Isentropic expansion – Turbine
• 4 – 1 : Constant pressure (and temperature)
heat rejection – Condenser
𝑻𝟑
𝜂𝒕𝒉 < 1-
𝑻𝟒
How to increase efficiency ?
Lecture PP 4
Mechanical Engineering Department
Efficiency improvement
1. Simple Rankine cycle:
Increase maximum temperature (superheat)
Increase boiler pressure (or maximum average temperature)
Decrease condenser temperature (and pressure)
2. Regenerative feed water heating
3. Reheating
4. Combined cycle
5. Heat and power (cogeneration)
Lecture PP 5
Mechanical Engineering Department
1. Simple cycle
Increase maximum temperature Increase boiler pressure Decrease minimum temperature
Limited by temperature of steel at fixed max. T increases average Less heat rejected higher
to be used (≈600 c). Increase temperature of heat addition will efficiency. Limited by available
steam quality at 4, decreasing decrease steam quality if no increase cold source. Adverse effect:
erosion damage of blades in max. T Lower steam quality
Lecture PP 6
Mechanical Engineering Department
Regenerative Heat exchange
Regeneration : Heat exchange between the fluid in one process during the power cycle and
the working fluid in another process of the cycle
• Idea : -> Carnotisation of process.
• Heat transfer during expansion recovered during boiling. For infinite number of heat
exchange steps : -> Carnot cycle
• With only heat exchange between steam and water, the main problem is decrease in
steam quality during expansion
• Solution : Bleed steam -> The steam is extracted at intermediate pressure and
condensed. Latent heat of condensation converted into sensible heat of condensate
• On the board …
Lecture PP 7
Mechanical Engineering Department
LP
Feed water Turbine
heaters (FWH) Unit size Number of
(MW) heaters
0-50 3-5
• The more feed
50-100 5 or 6
water heaters the
100-200 5-7
closer the cycle to
Over 200 6-8
Carnot cycle.
Power plant Engineering
& Veath
• Non contact heaters (NCFWH): Only need one pump on condensate loop
• Direct contact heaters: Pressure must be equal : additional pump.
However it allows deaeration of dissolved gas, e.g. O2 that leads to corrosion.
Source: Thermopedia
Lecture PP 8
Mechanical Engineering Department
Reheating
• Steam is sent back to boiler
after first expansion
• Can increase efficiency
depending on Point of reheating
• High steam quality after reheating
• Single stage reheat in normal power
plant, and double stage reheat in
supercritical power plant
Source Ohio.edu
Lecture PP 9
Mechanical Engineering Department
Combined cycle
Top and bottom cycle
Heat rejected from top cycle at
Tmin is used as high temperature
heat source of bottom cycle
• Water/steam and organic fluid
• Joule cycle + Rankine cycle
http://www.zeroco2.no/
Lecture PP 10
Mechanical Engineering Department
Heat recovery steam generator
• Pinch point temperature difference.
• Compromise on size of heat exchanger and
efficiency of the cycle
• The lower the temperature difference, the lower
the irreversibility in heat transfer
• CC cycle efficiency can be as high as 55-60 %
compared to 45-48 % for supercritical steam cycle.
• Sometimes HRSG have gas burners as boosters
Lecture PP 11
Mechanical Engineering Department
Combined Heat and Power – Cogeneration (CHP)
• Heat rejection typ. >40 %
• Can be used for heating, or processes (hospital, industry)
𝑒𝑙𝑒𝑐𝑡𝑟𝑖𝑐𝑖𝑡𝑦+𝑢𝑠𝑒𝑓𝑢𝑙 h𝑒𝑎𝑡
𝐸𝑛𝑒𝑟𝑔𝑦 𝑈𝑡𝑖𝑙𝑖𝑠𝑎𝑡𝑖𝑜𝑛 𝑓𝑎𝑐𝑡𝑜𝑟 𝐸𝑈𝐹 =
𝑜𝑢𝑡𝑝𝑢𝑡 𝑒𝑥𝑡𝑒𝑟𝑛𝑎𝑙 h𝑒𝑎𝑡 𝑎𝑑𝑑𝑖𝑡𝑖𝑜𝑛
• Industrial site : Local CHP to replace electricity purchase and on-plant
boiler means less transmission distribution loss
• Thermal efficiency could be 80%
Lecture PP 13
Mechanical Engineering Department
Lecture PP 14
Mechanical Engineering Department
Types of Cogeneration systems
Number of different cogeneration systems
are used, namely the following:
• Steam Turbine Cogeneration System
- The backpressure steam turbine
- The extraction condensing type steam turbine
• Internal Combustion Engine Cogeneration
System
• Gas Turbine Cogeneration System
Lecture PP 15
Mechanical Engineering Department
Classification of system
According to the sequence of energy use as
well as the operating procedure used.
• A topping cycle
fuel supplied first to produce power
and then in the process to produce
thermal energy
Lecture PP 16
Mechanical Engineering Department
• A bottoming cycle
fuel supplied first to produce
thermal energy at a high
temperature. The heat rejected in
the process is then further used to
generate power
Lecture PP 16
Mechanical Engineering Department
Combined cycle + Cogeneration
• Combined Cycle Heat and
Power (CCHP)
Cornell university
2 x 15 MW gas turbine
Double stage HRSG
As compared to on-site
(central heating) and off-
site (electricity sources):
-20 % CO2, -55% NOx,
- 55% SO2.
Lecture PP 17
Mechanical Engineering Department
Conclusions
1. Typical steam power plants have multiple feed water
heaters including a de-aerator, and at least a re heater
2. Additional utility gain by combined cycles, or combined
heat and power
3. Next lecture : focus on steam generators and combustor
from heat and mass transfer standpoint
