No: F/QCL/008 Rev.

01

MATERIAL SAFETY DATA SHEET

ACETONE

Revision : 02 Date : 3rd November, 2021 MSDS Number : 007

Section 1 - Chemical Product and Company Identification

1.1 Product Name : ACETONE

Synonyms : Dimethylketone; 2-propanone; dimethylketal
CAS No. : 67-64-1
HS Code : 2914 11 00
Molecular Weight : 58.08 g/mol
Chemical Formula : (CH3)2CO
Product Code : A-1005
Brand : SMART-LAB
1.2 Manufacturer : PT.Smart-Lab Indonesia
Address : Ruko Boulevard Taman Tekno Blok E No.10-11,BSD Sektor XI Serpong,
Tangerang - Indonesia
Website : www.smartlab.co.id
Email : [email protected]
For information : Telp: +62-21- 7588 0205(Hunting) , fax:+62-21-7588 0198
1.3 Application : General Chemical reagent
Emergency Telephone: +62-21-7588 0205(Hunting)

Section 2 - Hazards Identification

2.1 Classification of the substance or mixture

Classification according to Regulation (EC) No 1272/2008
Flammable liquids (Category 2), H225
Eye irritation (Category 2), H319
Specific target organ toxicity - single exposure (Category 3), Central nervous system, H336

For the full text of the H-Statements mentioned in this Section, see Section 16.

2.2 Label elements

Labelling according Regulation (EC) No 1272/2008
Pictogram

Signal word Danger

Hazard statement(s)
H225 Highly flammable liquid and vapour.
H319 Causes serious eye irritation.
H336 May cause drowsiness or dizziness.

Precautionary statement(s)
P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition
sources. No smoking.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing.
P370 + P378 In case of fire: Use dry powder or dry sand to extinguish.
P403 + P235 Store in a well-ventilated place. Keep cool.

Supplemental Hazard EUH066 Repeated exposure may cause skin dryness or cracking.
Statements

PT.SMART-LAB INDONESIA MSDS – ACETONE Page 1

No: F/QCL/008 Rev.01

MATERIAL SAFETY DATA SHEET

ACETONE

Revision : 02 Date : 3rd November, 2021 MSDS Number : 007

2.3 Other hazards

This substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic
(PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher

Section 3 - Composition, Information on Ingredients

3.1 Substances
Synonyms : Dimethylketone; 2-propanone; dimethylketal
Formula : (CH3)2CO
Molecular weight : 58.08 g/mol
CAS-No. : 67-64-1
EC-No. : 200-662-2
Index-No. : 606-001-00-8

Hazardous ingredients according to Regulation (EC) No 1272/2008

Component Classification Concentration

Flam. Liq. 2; Eye Irrit. 2; STOT
Acetone ≤ 100 %
SE 3; H225, H319, H336

For the full text of the H-Statements mentioned in this Section, see Section 16.

Section 4 - First Aid Measures

4.1 Description of first aid measures

General advice
Consult a physician. Show this safety data sheet to the doctor in attendance.

If inhaled
If breathed in, move person into fresh air. If not breathing, give artificial respiration. Consult a physician.
In case of skin contact
Wash off with soap and plenty of water. Consult a physician.

In case of eye contact

Rinse thoroughly with plenty of water for at least 15 minutes and consult a physician.

If swallowed
Do NOT induce vomiting. Never give anything by mouth to an unconscious person. Rinse mouth with water.
Consult a physician.

4.2 Most important symptoms and effects, both acute and delayed
The most important known symptoms and effects are described in the labelling (see section 2.2) and/or in
section 11

4.3 Indication of any immediate medical attention and special treatment needed
No data available

Section 5 - Firefighting Measures

PT.SMART-LAB INDONESIA MSDS – ACETONE Page 2

No: F/QCL/008 Rev.01

MATERIAL SAFETY DATA SHEET

ACETONE

Revision : 02 Date : 3rd November, 2021 MSDS Number : 007

5.1 Extinguishing media

Suitable extinguishing media
Use water spray, alcohol-resistant foam, dry chemical or carbon dioxide.

5.2 Special hazards arising from the substance or mixture

Carbon oxides

5.3 Advice for firefighters

Wear self-contained breathing apparatus for firefighting if necessary

5.4 Further information

Use water spray to cool unopened containers.

Section 6 - Accidental Release Measures

6.1 Personal precautions, protective equipment and emergency procedures

Use personal protective equipment. Avoid breathing vapours, mist or gas. Ensure adequate ventilation.
Remove all sources of ignition. Evacuate personnel to safe areas. Beware of vapours accumulating to form
explosive concentrations. Vapours can accumulate in low areas.
For personal protection see section 8.

6.2 Environmental precautions

Prevent further leakage or spillage if safe to do so. Do not let product enter drains.

6.3 Methods and materials for containment and cleaning up

Contain spillage, and then collect with an electrically protected vacuum cleaner or by wet-brushing and
place in container for disposal according to local regulations (see section 13).

6.4 Reference to other sections

For disposal see section 13.

Section 7 - Handling and Storage

7.1 Precautions for safe handling

Avoid contact with skin and eyes. Avoid inhalation of vapour or mist.
Keep away from sources of ignition - No smoking.Take measures to prevent the build up of electrostatic
charge.
For precautions see section 2.2.

7.2 Conditions for safe storage, including any incompatibilities

Store in cool place. Keep container tightly closed in a dry and well-ventilated place. Containers which are
opened must be carefully resealed and kept upright to prevent leakage.
Storage class (TRGS 510): Flammable liquids

7.3 Specific end use(s)

Apart from the uses mentioned in section 1.2 no other specific uses are stipulated

Section 8 - Exposure Controls, Personal Protection

PT.SMART-LAB INDONESIA MSDS – ACETONE Page 3

No: F/QCL/008 Rev.01

MATERIAL SAFETY DATA SHEET

ACETONE

Revision : 02 Date : 3rd November, 2021 MSDS Number : 007

8.1 Control parameters

8.2 Exposure controls
Appropriate engineering controls
Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and at the
end of workday.

Personal protective equipment

Eye/face protection
Face shield and safety glasses Use equipment for eye protection tested and approved under appropriate
government standards such as NIOSH (US) or EN 166(EU).
Skin protection
Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique
(without touching glove's outer surface) to avoid skin contact with this product. Dispose of
contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash
and dry hands.

The selected protective gloves have to satisfy the specifications of EU Directive 89/686/EEC and the
standard EN 374 derived from it.

Body Protection
Impervious clothing, Flame retardant antistatic protective clothing., The type of protective equipment
must be selected according to the concentration and amount of the dangerous substance at the specific
workplace.

Respiratory protection
Where risk assessment shows air-purifying respirators are appropriate use (US) or type AXBEK (EN
14387) respirator cartridges as a backup to engine protection, use a full-face supplied air respirator. Use
respirators and components tested and approved under appropriate government standards such as
NIOSH (US) or CEN (EU).

Control of environmental exposure

Prevent further leakage or spillage if safe to do so. Do not let product enter drains. Discharge into the
environment must be avoided.

Section 9 - Physical and Chemical Properties

9.1 Information on basic physical and chemical properties

Appearance Form: liquid, clear
Colour: colourless
Odour pungent, weakly aromatic
Odour Threshold 0,1 ppm
pH 5 - 6 at 395 g/l at 20 °C
Melting point/freezing point Melting point/range: -94 °C - lit.
Initial boiling point and boiling range 56 °C at 1.013 hPa - lit.
Flash point -17.0 °C - closed cup
Evaporation rate No data available
Flammability (solid, gas) No data available
Upper/lower flammability or Upper explosion limit: 13 %(V)
explosive limits Lower explosion limit: 2 %(V)
Vapour pressure 400.0 mmHg at 39.5 °C
184.0 mmHg at 20.0 °C
Vapour density No data available
Relative density 0.79 g/cm3
Water solubility completely miscible

PT.SMART-LAB INDONESIA MSDS – ACETONE Page 4

No: F/QCL/008 Rev.01

MATERIAL SAFETY DATA SHEET

ACETONE

Revision : 02 Date : 3rd November, 2021 MSDS Number : 007

Partition coefficient: noctanol/water log Pow: -0.24

Auto-ignition temperature 465.0 °C
Decomposition temperature No data available
Viscosity No data available
Explosive properties Not data available
Oxidizing properties No data available

9.2 Other safety information

Surface tension 23.2 mN/m at 20.0 °C

Section 10 - Stability and Reactivity

10.1 Reactivity
No data available

10.2 Chemical stability

Stable under recommended storage conditions.

10.3 Possibility of hazardous reactions

No data available

10.4 Conditions to avoid

Heat, flames and sparks.

10.5 Incompatible materials

Bases, Oxidizing agents, Reducing agents, Acetone reacts violently with phosphorous oxychloride.

10.6 Hazardous decomposition products

Hazardous decomposition products formed under fire conditions. - Carbon oxides
In the event of fire: see section 5

Section 11 - Toxicological Information

11.1 Information on toxicological effects

Acute toxicity
LD50 Oral - Rat - 5,800 mg/kg(Acetone)
Remarks: Behavioral:Altered sleep time (including change in righting reflex). Behavioral:Tremor.
Behavioral:Headache. Ingestion may cause gastrointestinal irritation, nausea, vomiting and diarrhoea.
LC50 Inhalation - Rat - 8 h - 50,100 mg/m3(Acetone)
Remarks: Drowsiness Dizziness Unconsciousness
LD50 Dermal - Guinea pig - 7,426 mg/kg(Acetone)

Skin corrosion/irritation
Skin - Rabbit(Acetone)
Result: Mild skin irritation - 24 h

Serious eye damage/eye irritation

Eyes - Rabbit(Acetone)
Result: Eye irritation - 24 h

Respiratory or skin sensitisation

- Guinea pig(Acetone)

PT.SMART-LAB INDONESIA MSDS – ACETONE Page 5

No: F/QCL/008 Rev.01

MATERIAL SAFETY DATA SHEET

ACETONE

Revision : 02 Date : 3rd November, 2021 MSDS Number : 007

Result: Does not cause skin sensitisation.

Germ cell mutagenicity

No data available(Acetone)

Carcinogenicity
This product is or contains a component that is not classifiable as to its classification.(Acetone)
IARC: No component of this product present at levels greater than or equal to 0.1% is identified as
probable, possible or confirmed human carcinogen by IARC.

Reproductive toxicity
No data available(Acetone)

Specific target organ toxicity - single exposure

May cause drowsiness or dizziness.(Acetone)

Specific target organ toxicity - repeated exposure

No data available

Aspiration hazard
No data available(Acetone)

Additional Information
RTECS: Not available

To the best of our knowledge, the chemical, physical, and toxicological properties have not been
thoroughly investigated.(Acetone)
Kidney - Irregularities - Based on Human Evidence(Acetone)
Skin - Dermatitis - Based on Human Evidence(Acetone)

Section 12 - Ecological Information

12.1 Toxicity
Toxicity to fish LC50 - Oncorhynchus mykiss (rainbow trout) - 5,540 mg/l - 96 h(Acetone)
Toxicity to daphnia and LC50 - Daphnia magna (Water flea) - 8,800 mg/l - 48 h(Acetone)
other aquatic
invertebrates
Toxicity to algae Remarks: No data available

12.2 Persistence and degradability

Biodegradability Result: 91 % - Readily biodegradable
(OECD Test Guideline 301B)

12.3 Bioaccumulative potential

Does not bioaccumulate.

12.4 Mobility in soil

No data available

12.5 Results of PBT and vPvB assessment

This substance/mixture contains no components considered to be either persistent, bioaccumulative and
toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher.

PT.SMART-LAB INDONESIA MSDS – ACETONE Page 6

No: F/QCL/008 Rev.01

MATERIAL SAFETY DATA SHEET

ACETONE

Revision : 02 Date : 3rd November, 2021 MSDS Number : 007

12.6 Other adverse effects

No data available

Section 13 - Disposal Considerations

13.1 Waste treatment methods

Product
Burn in a chemical incinerator equipped with an afterburner and scrubber b highly flammable. Offer
surplus and non-recyclable solutions to a licensed disposal company.

Contaminated packaging
Dispose of as unused product.

Section 14 - Transport Information

14.1 UN number
ADR/RID: 1090 IMDG: 1090 IATA: 1090
14.2 UN proper shipping name
ADR/RID: ACETONE
IMDG: ACETONE
IATA: ACETONE
14.3 Transport hazard class(es)
ADR/RID: 3 IMDG: 3 IATA: 3
14.4 Packaging group
ADR/RID: II IMDG: II IATA: II
14.5 Environmental hazards
ADR/RID: no IMDG Marine pollutant: no IATA: no
14.6 Special precautions for user
No data available

Section 15 - Regulatory Information

15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture
This safety datasheet complies with the requirements of Regulation (EC) No. 1907/2006.
15.2 Chemical safety assessment
For this product a chemical safety assessment was not carried out

Section 16 - Additional Information

Full text of H-Statements referred to under sections 2 and 3.

EUH066 Repeated exposure may cause skin dryness or cracking.
H225 Highly flammable liquid and vapour.
H319 Causes serious eye irritation.
H336 May cause drowsiness or dizziness.

PT.SMART-LAB INDONESIA MSDS – ACETONE Page 7

No: F/QCL/008 Rev.01

MATERIAL SAFETY DATA SHEET

ACETONE

Revision : 02 Date : 3rd November, 2021 MSDS Number : 007

National Fire Protection Association (U.S.A.):

Health: 1
Flammability: 3
Reactivity: 0

Revision history :

Date Rev Description

16 may 17 01 -
3 Nov 21 02 thorough revision

Further information
The information above is believed to be accurate and represents the best information currently available to us.
However, we make no warranty of merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users should make their own investigations
to determine the suitability of the information for their particular purposes. In no event shall Smart-lab be liable
for any claims, losses, or damages of any third party or for lost profits or any special, indirect, incidental,
consequential or exemplary damages, howsoever arising, even if Smart-lab has been advised of the possibility of
such damages.

PT.SMART-LAB INDONESIA MSDS – ACETONE Page 8