Scribd Logo
Upload

Welcome to Scribd!

  • 9 views

    MS - Concrete Repair Work

    Uploaded by

    dartymind420
    This document provides a method statement for repairing concrete surface honeycomb up to 50mm deep. It outlines using a cement-sand mix or epoxy grout to fill voids. Procedures include removing loose material, wetting the surface, applying cement slurry or epoxy, and tamping at an angle for compaction. Safety measures like PPE, scaffolding inspection, and first aid facilities are also described. Supervision in two shifts and a site control room are required to monitor repair work.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    MS - Concrete Repair Work

    Uploaded by

    dartymind420
    9 views4 pages
    This document provides a method statement for repairing concrete surface honeycomb up to 50mm deep. It outlines using a cement-sand mix or epoxy grout to fill voids. Procedures include removing loose material, wetting the surface, applying cement slurry or epoxy, and tamping at an angle for compaction. Safety measures like PPE, scaffolding inspection, and first aid facilities are also described. Supervision in two shifts and a site control room are required to monitor repair work.

    Original Title

    MS- Concrete Repair work

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides a method statement for repairing concrete surface honeycomb up to 50mm deep. It outlines using a cement-sand mix or epoxy grout to fill voids. Procedures include removing loose material, wetting the surface, applying cement slurry or epoxy, and tamping at an angle for compaction. Safety measures like PPE, scaffolding inspection, and first aid facilities are also described. Supervision in two shifts and a site control room are required to monitor repair work.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    9 views4 pages

    MS - Concrete Repair Work

    Uploaded by

    dartymind420
    This document provides a method statement for repairing concrete surface honeycomb up to 50mm deep. It outlines using a cement-sand mix or epoxy grout to fill voids. Procedures include removing loose material, wetting the surface, applying cement slurry or epoxy, and tamping at an angle for compaction. Safety measures like PPE, scaffolding inspection, and first aid facilities are also described. Supervision in two shifts and a site control room are required to monitor repair work.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 4

    ODISHA POWER GENERATION CORPORATIONLIMITED

    PROJECT
    FGD –FGC PACKAGE FOR 2x660 MW TPP (UNIT – 3 &4)

    OWNER
    ODISHA POWER GENERATION CORPORATION LIMITED

    EPC CONTRACTOR ISGEC HEAVY ENGINEERING LIMITED

    OWNER'S
    STEAG ENERGY SERVICES, NOIDA
    CONSULTANT

    QFGDM BABCOCK POWER ENVIRONMENTAL INC.

    DOCUMENT TITLE METHOD STATEMENT FOR REPAIR OF CONCRETE SURFACE


    ( HONEYCOMB UP TO 50 MM ).
    DATE 23.06.2022
    DOCUMENT NO. EC0045-CIV-MS-09
    REV. NO. 00

    PREPARED BY Mr.Pradeep Behera

    REVIEWED BY Mr.RaghabaPradhan

    APPROVED BY
    TABLE OF CONTENTS

    SL.NO DESCRIPTION

    1.0 Objectives

    2.0 Scope

    3.0 Reference

    4.0 Material to be used

    5.0 Equipment

    6.0 Work Procedure

    7.0 Safety

    8.0 Supervision

    9.0 Control Room at Site

    1.0 Objectives :

    Procedure and method to be adopted for carrying out repairing of concrete


    surface honeycomb in a safe manner and recording details for proper
    measurement.

    2.0 Scope :
    The procedure is applicable for all concrete surface honeycomb repair subject to
    depth of honey comb up to 50 MM.

    3.0 Reference :

    ● Contract Specification

    ● Relevant IS Codes

    ● Approved Drawing
    4.0 Materials to be used :

    ● Cement as per IS:269

    ● Coarse and Fine aggregate as per IS:383

    ● Water as per IS:456

    ● Fosroc GP2/Rendroc/Equivalent from BASF and Sika

    5.0 Equipment :

    ● Wire Brush

    ● Chisel

    ● Hammer

    ● Plumb Bob

    ● Trowel

    ● Concrete Breaker/Chipping Machine

    6.0 Work Procedure :

    The depth of Honeycomb up to 50mm :-

    ● For repairing of surface air voids cement mix can be used by the ratio of 1.2 where
    cement is 1 part and sand is 2 part.

    ● Loose particles to be removed from the honeycomb area by hammer and wire brush.

    ● Surface of the pocket shall be made wet and cement slurry to be applied over it.

    ● Then GP2/Rendroc/Equivalent material to be filled at the pocket as as per


    manufacturer technical data sheet.

    ● Most of the tamping should be directed at a slight angle towards the side of the
    pocket to ensure maximum compaction and bond.

    ● Extra water shall not be used to facilitate finishing.

    ● If the depth of honeycomb exceeds 50mm :

     It will be dealt separately case to case basis.


    7.0 Safety :

    Providing Safe access i.e Ladders, Stair Cases and Platforms to go to the work place

    Providing hand rails , mid rails, toe boards

    Ensuring all workers wear proper PPEs

    Giving trailing to workers how to work safely at scaffolding deck.

    Checking scaffolding regularly

    Regular inspection of Electrical DBs, ELCBs, Cables

    Providing sufficient illumination during night times

    Providing proper fire fighting facilities

    Providing first aid and ambulance facility round the clock during concrete

    Providing proper Sign Boards

    8.0 Supervision :

    The RCM shall be over all in charge of all activities assisted by Construction Manager &
    Senior Engineers. Supervision shall be arranged by two shifts. The chart showing the
    names of individuals with shift duties shall be submitted two days before
    commencement of work.

    9.0 Control Room at Site :

    Control room shall be set up at a convenient place near work location to monitor and
    co-ordinate all activities. Mobile phones shall be issued to all key personnel for timely
    interaction with each other.

    You might also like