Rosemount 8700 Series Magnetic Flowmeter Systems
Rosemount 8700 Series Magnetic Flowmeter Systems
Rosemount 8700 Series Magnetic Flowmeter Systems
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
Rosemount 8700 Series
Magnetic Flowmeter Systems
THE 8700 SERIES...
• Rosemount 8712 C/D/U Transmitter - Easiest
to use local operator interface and works with
any manufacturer’s flowtubes
• Rosemount 8712H/8707 High-Signal System
- Pulsed dc solutions for the most demanding
flow measurement applications
• Rosemount 8705 - Fully welded flowtube for
maximum protection (standard ISO lay length)
• Rosemount 8711 - Economical, compact, and
light weight flowtube, provided with alignment
rings for easy installation
• Rosemount 8732/8742 Transmitter -
Integral-mount design eliminates wiring error,
backlit display for easy viewing, and
explosion-proof housing for hazardous
environments
• Rosemount 8742 Transmitter - Utilizing
advanced diagnostics (high process noise
detection, grounding/wiring diagnostic, and
electrode signal fault) increase magmeter
performance
Content
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 4
Product Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 19
Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 28
Magnetic Flowmeter Sizing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 36
Material Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 38
Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 39
Rosemount 8712 C/D/U/H and 8732C Configuration Data Sheet . . . . . . . . . . . . . . . . . . . .page 52
Rosemount 8742C Configuration Data Sheet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 54
www.rosemount.com
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
2
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
8742-8742011ad
transmitter, a red light is triggered in the transducer block
(Figure 1) and detailed informative help screens list
appropriate recommendations for the grounding/wiring
diagnostic (Figure 2).
Process noise caused by slurries, high consistency pulp
stock, or upstream chemical additions can result in
wavering, unsteady flow measurements. The 8742C high FIGURE 2. Informative help screens provide
process noise diagnostic monitors the signal to noise ratio direction to solve problems
and recommends steps to improve flow measurements. If
the transmitter detects a low signal-to noise ratio, the high Grounding/Wiring Fault
process noise diagnostic is triggered and suggests The transmitter detected high levels of 50/60Hz noise caused by
increasing the coil drive frequency to improve the improper wiring or poor process grounding.
signal-to-noise ratio (Figure 3). By changing the coil drive
1. Connect ground rings, grounding electrode, lining protector,
frequency, a two to four times improvement in signal or grounding straps. Grounding diagrams are included in
stability is typical and results in a more consistent flow the flowtube products manual.
measurement and thus creating an opportunity for tighter 2. Verify flowtube is full.
control.
3. Verify wiring between flowtube and transmitter is prepared
Flowtube failures caused by liner failure, faulty electrode properly. Shielding should be stripped back less than 2.5 cm
(1in.).
connections or internal moisture can result in expensive,
unscheduled shut-downs. In a standard magmeter 4. Use separate shielded twisted pairs for wiring between
flowtube and transmitter.
installation, this type of flowtube failure could drop the
output flowrate by 50% without notifying the user. The 5. Properly connect the wiring between the flowtube and the
transmitter on the flowtube.
8742C electrode fault diagnostic analyzes the electrode
signal to monitor status and then produces a detailed, To turn off grounding/wiring diagnostic, go to the diagnostic
informative help screen that lists the appropriate remedies screen in the transducer block properties.
when the diagnostic is triggered.
FIGURE 3. Increasing coil drive frequency increases the
Diagnostics that proactively suggest the optimum software signal to noise ratio
configuration, provide powerful information through AMS
help screens, or a local display have never been available
before. Each diagnostic has unique help screens. These
Flow Signal
diagnostics are only the beginning. The 8742C is the
Amplitude
standard of the future for magnetic flowmeter diagnostics
that increase process stability, reduce commissioning time,
Noise at 5 Hz
8742-8742_05
3
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
NOTE
HART Communication requires a minimum loop resistance of 250
ohms.
4
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
Output Signals Turn-on Time
8712C/U/H: 30 minutes to rated accuracy from power up,
Analog Output Adjustment
5 seconds from power interruption
4–20 mA, jumper-selectable as internally or externally
8712D: 5 minutes to rated accuracy from power up, 5 seconds
powered 5 to 24 V dc; 0 to 1000 Ω load.
from power interruption
Engineering units—lower and upper range values
are user-selectable. Start-up Time
Output automatically scaled to provide 4 mA at lower range 0.2 seconds from zero flow
value and 20 mA at upper range value. Full scale continuously
adjustable between -30 and 30 ft/s (-10 to 10 m/sec), 1 ft/s Low Flow Cutoff
(0.3 m/s) minimum span. Adjustable between 0.04 and 1 ft/s (0.01 and 0.3 m/s). Below
HART Communications, digital flow signal, superimposed on selected value, output is driven to the zero flow rate signal level.
4–20 mA signal, available for control system interface. 250 Ω (8712D is adjustable between 0.01 and 1 ft/s).
required for HART communications.
Overrange Capability
Scalable Frequency Adjustment Signal output will remain linear until 110% of upper range value.
8712C/U/H: 0-1000 Hz, externally powered at 5 to 24 V dc, The signal output will remain constant above these values. Out of
transistor switch closure up to 5.75 w. Pulse value can be set range message displayed on LOI and the HART Communicator.
to equal desired volume in selected engineering units. Pulse
width adjustable from 0.5 to 100 m/s. Local operator interface Damping
automatically calculates and displays maximum allowable 8712C/U/H: Adjustable between 0.2 and 256 seconds
output frequency. 8712D: Adjustable between 0.0 and 256 seconds
8712D: 0-10,000Hz, externally powered at 5 to 24 V dc,
transistor switch closure supports power loads up to 2W for Flowtube Compensation
frequencies up to 4000Hz, and 5 V dc at 0.1 W at maximum Rosemount flowtubes are flow-calibrated and assigned a
frequency of 10,000 Hz. Pulse can be set to equal desired calibration factor at the factory. The calibration factor is entered
velocity or volume in user selectable engineering units. Pulse into the transmitter, enabling interchangeability of flowtubes
width is adjustable from 1.5 to 500 msec, below 1.5 msec without calculations or a compromise in accuracy.
pulse width automatically switches to 50% duty cycle. 8712U/D transmitters and other manufacturer’s flowtubes can be
calibrated at known process conditions or at the Rosemount
Auxiliary Output Function NIST-Traceable Flow Facility. Transmitters calibrated on site
Externally powered at 5 to 24 V dc, transistor switch closure require a two-step procedure to match known flow rate.
up to 3 W to indicate either:
Reverse Flow: Activates switch closure output when reverse
flow is detected. The reverse flow rate is displayed.
Zero Flow: Activates switch closure output when flow
goes to 0 ft/s.
Software Lockout
Security lockout jumper on the electronics board can be set to
deactivate all LOI and HART-based communicator functions to
protect configuration variables from unwanted or
accidental change.
Output Testing
Analog Output Test
Transmitter may be commanded to supply a specified current
between 3.75 and 23.25 mA
5
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
6
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
Storage
Operating –40 to 185 °F (–40 to 85 °C)
500
Region
Humidity Limits
0–100% RH to 150 °F (65 °C)
0
10.8 42
Power Supply (Volts) Enclosure Rating
NEMA 4X CSA Type 4X, IEC 60529, IP67 (transmitter),
Rmax = 41.7(Vps – 10.8) Pollution Degree 2
Vps = Power Supply Voltage (Volts)
Rmax = Maximum Loop Resistance (Ohms)
NOTE
HART Communication requires a minimum loop resistance of 250
ohms.
7
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
Overrange Capability
Signal output will remain linear until 110% of upper range value or
33 ft/s. The signal output will remain constant above these values.
Out of range message displayed on LOI and the
HART Communicator.
Damping
Adjustable between 0.2 and 256 seconds
Flowtube Compensation
Rosemount flowtubes are flow-calibrated and assigned a
calibration factor at the factory. The calibration factor is entered
into the transmitter, enabling interchangeability of flowtubes
without calculations or a compromise in accuracy.
8
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
Repeatability Mounting
±0.1% of reading Transmitter is mounted integrally with the flowtube and does not
require interconnecting cables.
Response Time
0.2 seconds maximum response to step change in input Transmitter Weight
Approximately 7 pounds (3.2 kg). Add 1 pound (0.5 kg) for Option
Stability Code M4.
±0.1% of rate over six months
EMC Compliance
EN61326-1 1997 + A1/A2 (Industrial) electromagnetic
compatibility (EMC) for process and laboratory apparatus.
9
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
0.75
Derivative (PID)
Intergrator 12,000 20
0.5
Reverse Flow
0.25 Detects and reports reverse flow
0
15 20 30 40 50 Software Lockout
Power Supply (Volts) A write-lock switch and software lockout are provided in the
I = 10/V resource function block.
I = Supply current requirement (Amps)
V = Power supply voltage (Volts) Turn-on Time
30 minutes to rated accuracy from power up;
Installation Coordination 10 seconds communication from power interruption
Installation (overvoltage) Category II
Start-up Time
Power Consumption 0.2 seconds from zero flow
10 watts maximum
Low Flow Cutoff
Ambient Temperature Limits Adjustable between 0 and 1 ft/s. Below selected value, output is
driven to the zero flow rate.
Operating
–40 to 165 °F (–40 to 74 °C) without local operator interface Overrange Capability
–13 to 147 °F (–25 to 65 °C) with local operator interface Signal output continues to 110% of upper range value setting, then
remains constant. Messages are supplied to the fieldbus network.
Storage
–40 to 185 °F (–40 to 85 °C) Damping
Adjustable between 0 and 255 seconds
Humidity Limits
0–100% RH to 150 °F (65 °C)
10
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
EMC Compliance
EN61326-1 1997 + A1/A2 3(Industrial) electromagnetic
compatibility (EMC) for process and laboratory apparatus.
Transient Protection
The 8742C transmitter prevents damage to the flowmeter from
transients compliant to:
IEC 6100 – 4-4 (for burst currents)
IEC 6100 – 4-5 (for surge currents)
11
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
PFA Lining
-20 to 350 °F (-29 to 177°C)
Polyurethane Lining
0 to 140 °F (–18 to 60 °C)
Neoprene Lining
0 to 185 °F (–18 to 85 °C)
Linatex Lining
0 to 158 °F (–18 to 70°C)
12
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
(2) 30- and 36-inch AWWA C207 Table 3 Class D rated to 150 psi at atmospheric temperature.
13
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
Rosemount 8707 with 8712D/C/U/H, 8732C, or 8742C DIN PN 10, 16, 25, and 40
±0.5% of rate from 3 to 30 ft/s (1 to 10 m/s). Include combined PN10: Not available for flange sizes from 15 to 150 mm
effects of linearity, hysteresis, repeatability and calibration PN16: Not available for flange sizes from 15 to 80 mm
uncertainty. Accuracy is ±0.015 ft/s (±0.0045 m/s) from
PN 25: Not available for flange sizes from 15 to 150 mm
low-flow cutoff to 3.0 ft/s (1 m/s).
PN40: Available for all flange sizes
Vibration Effect
AS 2129 Table D and E
IEC 60770-1
0.5- to 36 inch
Mounting Position Effect
AISI Type 304 SST Sanitary Tri-Clover
None when installed to ensure flowtube remains full
3-A-compliant quick disconnect ferrule-mounted to ASME
B16.5 (ANSI) Class 150 flange; 0.5- to 3-inch.
Physical Specifications
Electrical Connections
Non-Wetted Materials Two ¾–14 NPT connections with number 8 screw terminals are
Flowtube provided in the terminal enclosure for electrical wiring.
AISI Type 304 SST
Grounding Electrode
Flanges A grounding electrode is installed similarly to the measurement
electrodes through the flowtube lining on 8705 flowtubes. It is
Carbon steel, AISI Type 304/304L SST,
available in all electrode materials.
or Type 316/316L SST
Weight
See Table 5 and Table 6
14
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
15
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
Service Accuracy
Conductive liquids and slurries Rosemount 8711 with 8712C/U, 8732C, or
8742C Transmitters
Line Sizes
±0.5% of rate from 3 to 30 ft/s (1 to 10 m/s)
0.15- through 8-inch (4 through 200 mm)
±0.015 ft/s (0.0045 m/s) from low-flow cutoff to 3 ft/s (1 m/s)
Interchangeability
Rosemount 8711 Flowtubes are interchangeable with 8712C/U, Vibration Effect
8732, and 8742C Transmitters. System accuracy is maintained IEC 60770-1
regardless of line size or optional features. Each flowtube
nameplate has a sixteen-digit calibration number that can be Mounting Position Effect
entered into a transmitter through the Local Operator Interface No effect when installed to ensure flowtube remains full
(LOI) or the HART Communicator on the Rosemount 8712C/U/H
and the 8732C. In a FOUNDATION fieldbus environment, the 8742C Physical Specifications
can be configured using the DeltaV fieldbus configuration tool or
another FOUNDATION fieldbus configuration device. No further Non-Wetted Materials
calibration is necessary.
Flowtube
Upper Range Limit 303 SST (ASTM A-743)
30 ft/s (10 m/s)
Coil Housing
Process Temperature Limits Investment cast steel (ASTM A-27)
Conductivity Limits
Process liquid must have a conductivity of 5 microsiemens/cm (5
micromhos/cm) or greater for 8711. Excludes the effect of
interconnecting cable length in remote mount
transmitter installations.
16
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
Process Connections
Mounts between these Flange Configurations
ASME B16.5 (ANSI): Class 150, 300
DIN: PN 10 and 25
BS: 10 Table D, E, and F
Electrical Connections
Two ¾–14 NPT connections with number 8 screw terminals are
provided in the terminal enclosure for electrical wiring.
Grounding Electrode
A grounding electrode is installed similarly to the measurement
electrodes through the flowtube lining. It is available in all
electrode materials.
Grounding Rings
Grounding rings are installed between the flange and the tube face
on both ends of the flowtube. They have an I.D. slightly larger than
the flowtube I.D. and an external tab to attach ground wiring.
Grounding rings are available in 316L SST, Hastelloy C-276,
titanium, and tantalum.
17
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
Storage
–40 to 140 °F (–40 to 60 °C)
Humidity Limits
0 to 95% relative humidity
Performance Specifications
Accuracy
±0.05% of rate at 30 ft/s at 25°C
±0.10% of rate at 10 ft/s and 3 ft/s
Warm-up Time
30 minutes
Humidity Effect
No effect from 0 to 60% relative humidity
< 0.10% of rate from 60 to 90% relative humidity
Long-Term Stability
< 0.10% of rate shift in one year
Physical Specifications
Electrical Connections
Electrical connections are compatible with 8712C/U or 8732C
terminal blocks. Electrical connections are not compatible with
8712H terminal block.
Mounting
Any position is acceptable
Materials of Construction
Housing
Extruded aluminum
Covers
Stamped aluminum, silk-screened
Paint
Polyurethane
Weight
Approximately 3 lb (2 kg)
18
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
Product Certifications
Approved Manufacturing Locations Electro Magnetic Compatibility (EMC)
Rosemount Inc. — Eden Prairie, Minnesota, USA (89/336/EEC)
Fisher-Rosemount Technologias de Flujo, S.A. de C.V. — All Models EN 50081-1: 1992, EN 50082-2: 1995,
Chihuahua, Chihuahua, Mexico EN 61326: 1997/ A1:1998 / A2:2000
Installed signal wiring should not be run together and should not
EUROPEAN DIRECTIVE INFORMATION be in the same cable tray as AC power wiring.
The EC declaration of conformity for all applicable European Device must be properly grounded or earthed according to local
electric codes.
directives for this product can be found on our website at
www.rosemount.com. A hard copy may be obtained by contacting To improve protection against signal interference, shielded cable is
our local sales office. recommended.
19
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
(2) Refer to Table 9 on page 25 for relation between ambient temperature, process temperature, and temperature class.
Reference Rosemount Control Drawing 08742-1051 Explosion-Proof for Class I, Division 1, Groups C, D with IS
output for Class I, Division 1, Groups A, B, C, D.
(8742C) or 08732-1052 (8732C).
Temp Code – T4 at 60°C
Class I, Division 2, Groups A, B, C, D
Temp Codes – T4 (8712 at 40°C, 8742 at 60°C), Dust-ignition proof Class II/III, Division 1, Groups E, F, G
Temp Code – T6 at 60°C
T5 (8732 at 60°C)
Class I, Division 2, Groups A, B, C, D
Dust-ignition proof Class II/III, Division 1, Groups E, F, G
Temp Codes – T4 (8712 at 40°C), T6 (8732/8742 at 60°C) Temp Codes – T4 (8742 at 60°C)
Reference Rosemount Control Drawing 08742-1051 Reference Rosemount Control Drawing 08742-1051
(8742C) or 08732-1052 (8732C).
Class I, Division 2, Groups A, B, C, D with IS output for
Class I, Division 2, Groups A, B, C, D
Class I, Division 1, Groups A, B, C, D.
Temp Code – T4 at 60°C Temp Codes – T4 (8712 at 40°C, 8742 at 60°C),
T5 (8732 at 60°C)
Dust-ignition proof Class II/III, Division 1, Groups E, F, G
Temp Code – T6 at 60°C Dust-ignition proof Class II/III, Division 1, Groups E, F, G
Temp Codes – T4 (8712 at 40°C), T6 (8732/8742 at 60°C)
Enclosure Type 4X
Enclosure Type 4X
20
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
E5 Explosion-Proof Approval (8732 and 8742 only) European Certifications
Reference Rosemount Control Drawing 08732-1052 E1 ATEX Flameproof
Explosion-Proof for Class I, Division 1, Groups C, D Hydrogen gas group
Temp Code – T6 at 60°C 8732 - Certificate No.: 03ATEX2052X II 2G
Dust-ignition proof Class II/III, Division 1, Groups E, F, G EEx d IIB + H2 T6 (-20°C ≤ Ta ≤ +65°C)
Temp Code – T6 at 60°C 8742 - Certificate No.: 03ATEX2159X II 2G
Class I, Division 2, Groups A, B, C, D EEx de IIB + H2 T6 (-20°C ≤ Ta ≤ +65°C)
Temp Codes – T4 (8742 at 60°C), T5 (8732 at 60°C) When installed per drawing 08732-1050
Vmax = 250 V AC or 50 V DC
Enclosure Type 4X
0575
Canadian Standards Association (CSA) ED ATEX Flameproof
N0 Division 2 Approval Reference Rosemount Control Drawing 08732-1052
Reference Rosemount Control Drawing 08732-1051 8732 - Certificate No.: KEMA03ATEX2052X II 2G
(8732C or 8742C only) EEx d IIB T6 (Ta = -20°C to +65°C)
Vmax = 250 V AC or 50 V DC
Class I, Division 2, Groups A, B, C, D
0575
Temp Codes – T5 (8732 at 60°C), T4 (8742 at 60°C)
Dust-ignition proof Class II/III, Division 1, Groups E, F, G
Enclosure Type 4X SPECIAL CONDITIONS FOR SAFE USE (X (03ATEX2052X):
If the Model 8732 Flow Transmitter is used integrally with the
K0 Division 2 Approval with
Model 8705 or 8711 Flowtubes, it shall be assured that the
Intrinsically Safe Output (8742 Only)
mechanical contact areas of the Flowtube and Flow Transmitter
Reference Rosemount Control Drawing 08742-1052 comply with the requirements for flat joints according to standard
Class I, Division 2, Groups A, B, C, D with IS output for EN 50018, clause 5.2.
Class I, Division 1, Groups A, B, C, D. Temp Code – T4 at
60°C The relation between ambient temperature, process temperature,
Dust-ignition proof Class II/III, Division 1, Groups E, F, G and temperature class is to be taken from the table under (15 -
Temp Code – T6 at 60°C description) above. (See Table 9)
Enclosure Type 4X
The electrical data is to be taken from the summary under (15 -
electrical data) above. (See Table 10)
INSTALLATION INSTRUCTIONS:
The cable and conduit entry devices and blanking elements shall
be of a certified flameproof type, suitable for the conditions of use
and correctly installed. With the use of conduit, a certified stopping
box shall be provided immediately to the entrance of the
enclosure.
21
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
INSTALLATION INSTRUCTIONS:
The cable and conduit entry devices and the closing elements
shall be of a certified increased safety type, suitable for the
conditions of use and correctly installed.
N1 ATEX (Pending)
8712D - ATEX Certificate No:
EEx nA nL IIC T4
22
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
(2) Refer to Table 9 on page 25 for relation between ambient temperature, process temperature, and temperature class.
23
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
SPECIAL CONDITIONS FOR SAFE USE (X): SPECIAL CONDITIONS FOR SAFE USE (X):
If the Model 8732 Flow Transmitter is used integrally with the If the Model 8732 Flow Transmitter is used integrally with the
Model 8705 or Model 8711 Flowtubes, it shall be assured that the Model 8705 or Model 8711 Flowtubes, it shall be assured that the
mechanical contact areas of the Flowtube and Flow Transmitter mechanical contact areas of the Flowtube and Flow Transmitter
comply with the requirements for flat joints according to standard comply with the requirements for flat joints according to standard
EN 50018, clause 5.2. The relation between ambient temperature, EN 50018, clause 5.2. The relation between ambient temperature,
process temperature and temperature class is to be taken from the process temperature and temperature class is to be taken from the
table under (15-description) above. - (See certificate) The table under (15-description) above. - (See certificate) The
electrical data is to be taken from the summary under (15-electrical electrical data is to be taken from the summary under (15-electrical
data above). data above).
INSTALLATION INSTRUCTIONS:
At ambient temperature above 50°C, the flowmeter shall be used
with heat resistant cables with a temperature rating of at least
90°C.
24
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
TABLE 9. Relation between ambient temperature, process temperature, and temperature class(1)
Meter Size (Inches) Maximum Ambient Temperature Maximum Process Temperature Temperature Class
1/2 149°F (65°C) 297°F (147°C) T3
1 149°F (65°C) 318°F (159°C) T3
1 95°F (35°C) 232°F (111°C) T4
11/2 149°F (65°C) 297°F (147°C) T3
11/2 140°F (60°C) 171°F (77°C) T4
2 149°F (65°C) 289°F (143°C) T3
2 149°F (65°C) 163°F (73°C) T4
2 104°F (40°C) 144°F (62°C) T5
3 - 36 149°F (65°C) 351°F (177°C) T3
3 - 36 149°F (65°C) 210°F (99°C) T4
3 - 36 131°F (55°C) 144°F (62°C) T5
3 - 36 104°F (40°C) 144°F (62°C) T6
(1) This table is applicable for CD and KD option codes only.
25
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
TABLE 11. Relation between the maximum ambient temperature, the maximum process temperature,
and the temperature class(1)
Maximum process temperature °F (°C) per temperature class
Maximum Ambient
Temperature T3 T4 T5 T6
0.5 inch flowtube size
149°F (65°C) 297°F (147°C) 138°F (59°C) 54°F (12°C) 18°F (-8°C)
140°F (60°C) 309°F (154°C) 151°F (66°C) 66°F (19°C) 28°F (-2°C)
131°F (55°C) 322°F (161°C) 163°F (73°C) 79°F (26°C) 41°F (5°C)
122°F (50°C) 334°F (168°C) 176°F (80°C) 90°F (32°C) 54°F (12°C)
113°F (45°C) 347°F (175°C) 189°F (87°C) 102°F (39°C) 66°F (19°C)
104°F (40°C) 351°F (177°C) 199°F (93°C) 115°F (46°C) 79°F (26°C)
95°F (35°C) 351°F (177°C) 212°F (100°C) 127°F (53°C) 90°F (32°C)
86°F (30°C) 351°F (177°C) 225°F (107°C) 138°F (59°C) 102°F (39°C)
77°F (25°C) 351°F (177°C) 237°F (114°C) 151°F (66°C) 115°F (46°C)
68°F (20°C) 351°F (177°C) 248°F (120°C) 163°F (73°C) 127°F (53°C)
1.0 inch flowtube size
149°F (65°C) 318°F (159°C) 158°F (70°C) 72°F (22°C) 34°F (1°C)
140°F (60°C) 331°F (166°C) 171°F (77°C) 84°F (29°C) 46°F (8°C)
131°F (55°C) 343°F (173°C) 183°F (84°C) 97°F (36°C) 59°F (15°C)
122°F (50°C) 351°F (177°C) 196°F (91°C) 109°F (43°C) 72°F (22°C)
113°F (45°C) 351°F (177°C) 207°F (97°C) 122°F (50°C) 84°F (29°C)
104°F (40°C) 351°F (177°C) 219°F (104°C) 135°F (57°C) 97°F (36°C)
95°F (35°C) 351°F (177°C) 232°F (111°C) 145°F (63°C) 109°F (43°C)
86°F (30°C) 351°F (177°C) 244°F (118°C) 158°F (70°C) 122°F (50°C)
77°F (25°C) 351°F (177°C) 257°F (125°C) 171°F (77°C) 135°F (57°C)
68°F (20°C) 351°F (177°C) 270°F (132°C) 183°F (84°C) 145°F (63°C)
1.5 inch flowtube size
149°F (65°C) 297°F (147°C) 160°F (71°C) 88°F (31°C) 55°F (13°C)
140°F (60°C) 307°F (153°C) 171°F (77°C) 97°F (36°C) 66°F (19°C)
131°F (55°C) 318°F (159°C) 181°F (83°C) 108°F (42°C) 77°F (25°C)
122°F (50°C) 329°F (165°C) 192°F (89°C) 118°F (48°C) 88°F (31°C)
113°F (45°C) 340°F (171°C) 203°F (95°C) 129°F (54°C) 97°F (36°C)
104°F (40°C) 351°F (177°C) 214°F (101°C) 140°F (60°C) 108°F (42°C)
95°F (35°C) 351°F (177°C) 223°F (106°C) 151°F (66°C) 118°F (48°C)
86°F (30°C) 351°F (177°C) 234°F (112°C) 160°F (71°C) 129°F (54°C)
77°F (25°C) 351°F (177°C) 244°F (118°C) 171°F (77°C) 140°F (60°C)
68°F (20°C) 351°F (177°C) 255°F (124°C) 181°F (83°C) 151°F (66°C)
Continued on Next Page
26
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
TABLE 11. Relation between the maximum ambient temperature, the maximum process temperature,
and the temperature class(1)
Maximum process temperature °F (°C) per temperature class
Maximum Ambient
Temperature T3 T4 T5 T6
2.0 inch flowtube size
149°F (65°C) 289°F (143°C) 163°F (73°C) 95°F (35°C) 66°F (19°C)
140°F (60°C) 300°F (149°C) 172°F 78(°C) 104°F (40°C) 75°F (24°C)
131°F (55°C) 309°F (154°C) 183°F (84°C) 115°F (46°C) 84°F (29°C)
122°F (50°C) 318°F (159°C) 192°F (89°C) 124°F (51°C) 95°F (35°C)
113°F (45°C) 329°F (165°C) 201°F (94°C) 135°F (57°C) 104°F (40°C)
104°F (40°C) 338°F (170°C) 212°F (100°C) 144°F (62°C) 115°F (46°C)
95°F (35°C) 349°F (176°C) 221°F (105°C) 153°F (67°C) 124°F (51°C)
86°F (30°C) 351°F (177°C) 232°F (111°C) 163°F (73°C) 135°F (57°C)
77°F (25°C) 351°F (177°C) 241°F (116°C) 172°F (78°C) 144°F (62°C)
68°F (20°C) 351°F (177°C) 252°F (122°C) 183°F (84°C) 153°F (67°C)
3 to 60 inch flowtube size
149°F (65°C) 351°F (177°C) 210°F (99°C) 117°F (47°C) 75°F (24°C)
140°F (60°C) 351°F (177°C) 223°F (106°C) 129°F (54°C) 90°F (32°C)
131°F (55°C) 351°F (177°C) 237°F (114°C) 144°F (62°C) 102°F (39°C)
122°F (50°C) 351°F (177°C) 250°F (121°C) 156°F (69°C) 117°F (47°C)
113°F (45°C) 351°F (177°C) 264°F (129°C) 171°F (77°C) 129°F (54°C)
104°F (40°C) 351°F (177°C) 266°F (130°C) 183°F (84°C) 144°F (62°C)
95°F (35°C) 351°F (177°C) 266°F (130°C) 198°F (92°C) 156°F (69°C)
86°F (30°C) 351°F (177°C) 266°F (130°C) 203°F (95°C) 171°F (77°C)
77°F (25°C) 351°F (177°C) 266°F (130°C) 203°F (95°C) 176°F (80°C)
68°F (20°C) 351°F (177°C) 266°F (130°C) 203°F (95°C) 176°F (80°C)
(1) This table is applicable for N1 option codes only.
27
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
Dimensional Drawings
FIGURE 4. Rosemount 8712C/U/H Transmitter
11.15
LOI Keypad
(283)
Cover 12.02
(305)
2.96
(75)
17.70 (450)
¾–14 NPT
Conduit 11.37
Connection (289)
(3 Places) 8712-12A01A, 8712B01A, 8712C01A, 8712D01A
Ground Lug
NOTE
Dimensions are in inches (millimeters)
28
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
7.49 (190)
6.48 (165)
1.94 LOI Cover
(49)
3
/4”-14 NPT Electrical
5.10 3.00 Conduit Connections
(130) (76) (2 places)
8.81
10.5 (224)
(267)
3.07
(78)
3.43
3
(87) /4”-14 NPT
Flowtube Conduit
Connections
(2 places)
11.02
(280)
5.82
(148)
8742-8742_06A, 8742_06B, 1002G01A
Note
Dimensions in inches (millimeters)
29
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
FIGURE 6. Rosemount 8705 and 8707 Flowtubes, Typical of 0.5- through 4-inch (15 through 100 mm) Line Sizes
4.02 5.00
(102) (127)
2.00
(50.8)
2.6
1.8
2.6 (66)
(46)
(66)
3 H
/4-14 NPT
Conduit
Connection C
Relief
8705-1002A05A, 1002B05A
Valve
Notes A L
Dimensions are in inches (millimeters)
See Table 13 and Table 14 for variable dimensions
W1 Housing Configuration (Sealed, welded housing with pressure relief valve)
FIGURE 7. Rosemount 8705 and 8707 Flowtubes, Typical of 6- through 36-inch (150 through 900 mm) Line Sizes
4.02
(102)
2.00
(51) 5.00
1.8 (127)
2.6 (46)
2.66
(66)
(66)
8705-1002A06A, 1002B06A
W3 Housing
Configuration
L
A Notes
Dimensions are in inches (millimeters)
D See Table 13 and Table 14 for variable dimensions
W3 Housing Configuration (Sealed welded housing with
separate electrode compartments)
30
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
FIGURE 8. Rosemount 8705 Sanitary Flowtubes, Typical of 1/2- through 3-inch (15 through 86 mm) Line Sizes
4.02
(102)
2.00
5.00
(50.8)
(127)
1.8
2.6 (46) 2.6
(66) (66)
3/4-14
Grounding
NPT Clamp
E C
Conduit
Connection
8705-1002A05A, 1002B05D
Notes
L
Dimensions are in inches (millimeters)
See Table 14 for available dimensions
W0 Housing Configuration (Sealed welded housing)
31
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
TABLE 13. Rosemount 8705 and 8707 Dimensions in Inches (Millimeters) (Dimensions with ASME B16.5 (ANSI) Flanges) (1)
Refer to Dimensional Drawings, Figure 6, Figure 7, and Figure 8
Liner Face Overall Flowtube
Line Size(2) and Body Height Diameter Length Flange Diameter
Flange Rating “H” “A” “L”(3) “D” Liner Thickness Inside Diameter
0.5–150 6.75 (171) 1.38 (35) 7.88 (200) 3.50 (89) 0.09 (2.3) 0.49 (12.5)
0.5–300 6.75 (171) 1.38 (35) 7.88 (200) 3.75 (95) 0.09 (2.3) 0.49 (12.5)
0.5–600 6.75 (171) 1.38 (35) 8.67 (220) 3.75 (95) 0.09 (2.3) 0.49 (12.5)
1–150 6.75 (171) 2.00 (51) 7.88 (200) 4.25 (108) 0.09 (2.3) 0.91 (23)
1–300 6.75 (171) 2.00 (51) 7.88 (200) 4.88 (124) 0.09 (2.3) 0.91 (23)
1–600 6.75 (171) 1.62 (41) 8.67 (220) 4.88 (124) 0.09 (2.3) 0.91 (23)
1–900 6.75 (171) 1.62 (41) 9.66 (245) 5.88 (149) 0.13 (3.3) 0.80 (20)
1.5–150 7.10 (180) 2.88 (73) 7.88 (200) 5.00 (127) 0.12 (3.1) 1.44 (37)
1.5 –300 7.10 (180) 2.88 (73) 7.88 (200) 6.12 (155) 0.12 (3.1) 1.44 (37)
1.5–600 7.10 (180) 2.88 (73) 8.63 (219) 6.12 (155) 0.13 (3.3) 1.36 (35)
1.5–900 7.10 (180) 2.50 (64) 9.52 (242) 7.00 (178) 0.13 (3.3) 1.25 (32)
2–150 7.10 (180) 3.62 (92) 7.88 (200) 6.00 (152) 0.12 (3.1) 1.91 (49)
2–300 7.10 (180) 3.62 (92) 7.88 (200) 6.50 (165) 0.12 (3.1) 1.91 (49)
2–600 7.10 (180) 3.62 (92) 8.78 (223) 6.50 (165) 0.13 (3.3) 1.82 (46)
2–900 7.10 (180) 3.25 (83) 10.26 (261) 8.50 (216) 0.13 (3.3) 1.69 (43)
3–150 8.10 (206) 5.00 (127) 7.88 (200) 7.50 (191) 0.15 (3.8) 2.96 (75)
3–300 8.10 (206) 5.00 (127) 8.63 (219) 8.25 (210) 0.15 (3.8) 2.96 (75)
3–600 8.10 (206) 5.00 (127) 12.4 (315) 8.25 (210) 0.13 (3.3) 2.76 (70)
3–900 8.10 (206) 4.63 (118) 12.8 (326) 9.50 (241) 0.13 (3.3) 2.37 (60)
4–150 8.45 (215) 6.19 (157) 9.84 (250) 9.00 (229) 0.15 (3.8) 3.96 (101)
4–300 8.45 (215) 6.19 (157) 10.88 (276) 10.00 (254) 0.15 (3.8) 3.96 (101)
4–600 8.45 (215) 6.19 (157) 12.83 (326) 10.75 (273) 0.13 (3.3) 3.72 (95)
4–900 8.45 (215) 5.81 (148) 13.89 (353) 11.50 (292) 0.13 (3.3) 3.37 (86)
6–150 9.45 (240) 8.50 (216) 11.81 (300) 11.00 (279) 0.19 (4.8) 5.98 (152)
6–300 9.45 (240) 8.50 (216) 13.06 (332) 12.50 (318) 0.19 (4.8) 5.69 (144)
6–600 9.45 (240) 8.50 (216) 14.23 (361) 14.00 (356) 0.19 (4.8) 5.69 (144)
6–900 9.45 (240) 8.00 (203) 15.51 (394) 15.00 (381) 0.16 (4.1) 4.86 (123)
8–150 10.42 (265) 10.62 (270) 13.78 (350) 13.50 (343) 0.19 (4.8) 7.94 (202)
8–300 10.42 (265) 10.62 (270) 15.60 (396) 15.00 (381) 0.17 (4.3) 7.64 (194)
8–600 10.42 (265) 10.62 (270) 16.72 (428) 16.50 (419) 0.17 (4.3) 7.64 (194)
8–900 10.42 (265) 10.00 (254) 18.47 (469) 18.50 (470) 0.17 (4.3) 6.65 (169)
10–150 11.78 (299) 12.75 (324) 15.00 (381) 16.00 (406) 0.26 (6.5) 9.87 (251)
10–300 11.78 (299) 12.75 (324) 17.13 (435) 17.50 (444) 0.26 (6.5) 9.48 (241)
10–600 11.78 (299) 12.75 (324) 19.54 (496) 20.00 (508) 0.26 (6.5) 9.21 (234)
12–150 12.86 (327) 15.00 (381) 18.00 (457) 19.00 (483) 0.26 (6.7) 11.87 (301)
12–300 12.86 (327) 15.00 (381) 20.14 (512) 20.50 (52) 0.26 (6.7) 11.48 (292)
14–150 13.92 (354) 16.25 (413) 21.00 (533) 21.00 (533) 0.19 (4.8) 13.16 (334)
14–300 13.92 (354) 16.25 (413) 23.25 (591) 23.00 (584) 0.19 (4.8) 12.79 (325)
16–150 14.93 (379) 18.50 (470) 24.00 (610) 23.50 (597) 0.19 (4.8) 15.12 (384)
16–300 14.93 (379) 18.50 (470) 26.25 (667) 25.50 (648) 0.19 (4.8) 14.75 (375)
18–150 16.19 (411) 21.00 (533) 27.00 (686) 25.00 (635) 0.19 (4.8) 17.09 (434)
18–300 16.19 (411) 21.00 (533) 30.12 (765) 28.00 (711) 0.19 (4.8) 16.35 (415)
20–150 17.20 (437) 23.00 (584) 30.00 (762) 27.50 (698) 0.19 (4.8) 18.96 (482)
20–300 17.20 (437) 23.00 (584) 33.25 (845) 30.50 (774) 0.19 (4.8) 18.21 (463)
24–150 19.48 (495) 27.25 (692) 36.00 (914) 32.00 (813) 0.19 (4.8) 22.94 (583)
24–300 19.48 (495) 27.25 (692) 39.64 (1007) 36.00 (914) 0.19 (4.8) 22.06 (560)
30 22.23 (565) 33.80 (859) 37.25 (946) 38.75 (984) 0.19 (4.8) 28.75 (730)
36 26.10 (663) 40.27 (1023) 40.88 (1038) 46.00 (1168) 0.19 (4.8) 29.08 (739)
(1) AS2129 Table D and E flange dimensions match ANSI 150# dimensions.
(2) 30- and 36-inch AWWA C207 Table 2 Class D rated to 150 psi at 150 °F.
(3) When 2 grounding rings are specified, add 0.25 inch (6.35 mm) for 0.50- through 14-inch (15 through 350 mm) flowtubes, add 0.50 inch (12.7 mm) for
16-inch (400 mm) and larger. When lining protectors are specified, add 0.25 inch (6.35 mm) for ½- through 12-inch (15 through 300 mm) flowtubes, add
0.50 inch (12.7 mm) for 14- through 36-inch (350 through 900 mm) flowtubes.
32
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
TABLE 14. Rosemount 8705 Flowtube Dimensions with DIN Flanges in Millimeters (Inches)
Line Size(1) Liner Face
and Flange Body Height Diameter Overall Flowtube Flange Diameter
Rating “H” “A” Length “L”(2) “D” Liner Thickness Inside Diameter
15 mm PN 10–40 171 (6.75) 45 (1.77) 200 (7.88) 95 (3.74) 2.3 (0.09) 12.5 (.49)
25 mm PN 10–40 171 (6.75) 68 (2.68) 200 (7.88) 115 (4.53) 2.3 (0.09) 23.1 (.91)
40 mm PN 10–40 180 (7.10) 88 (3.46) 200 (7.87) 150 (5.91) 3.1 (0.12) 37 (1.44)
50 mm PN 10–40 180 (7.10) 102 (4.02) 200 (7.87) 165 (6.50) 3.1 (0.12) 49 (1.91)
80 mm PN 10–40 206 (8.10) 138 (5.43) 200 (7.87) 200 (7.87) 3.8 (0.15) 75.2 (2.96)
100 mm PN 10–16 215 (8.45) 162 (6.38) 250 (9.84) 220 (8.66) 3.8 (0.15) 100.6 (3.96)
100 mm PN 25–40 215 (8.45) 162 (6.38) 250 (9.84) 235 (9.25) 3.8 (0.15) 100.6 (3.96)
150 mm PN 10 240 (9.45) 212 (8.35) 300 (11.81) 285 (11.22) 4.7 (0.19) 152 (5.98)
150 mm PN 16 240 (9.45) 215 (8.46) 300 (11.81) 220 (8.66) 4.7 (0.19) 152 (5.98)
150 mm PN 25 240 (9.45) 218 (8.58) 300 (11.81) 300 (11.81) 4.7 (0.19) 152 (5.98)
150 mm PN 40 240 (9.45) 218 (8.58) 332 (13.07) 300 (11.81) 4.7 (0.19) 144 (5.67)
200 mm PN 10 265 (10.42) 268 (10.55) 350 (13.78) 240 (13.39) 4.9 (0.19) 202 (7.94)
200 mm PN 16 265 (10.42) 268 (10.55) 350 (13.78) 340 (13.39) 4.9 (0.19) 202 (7.94)
200 mm PN 25 265 (10.42) 278 (10.94) 350 (13.78) 360 (14.17) 4.9 (0.19) 202 (7.94)
200 mm PN 40 265 (10.42) 285 (11.22) 396 (15.60) 375 (14.76) 4.3 (0.17) 194 (7.64)
250 mm PN 10 299 (11.78) 320 (12.60) 381 (15.00) 395 (15.55) 6.6 (0.26) 251 (9.88)
250 mm PN 16 299 (11.78) 320 (12.60) 381 (15.00) 405 (15.94) 6.6 (0.26) 251 (9.88)
250 mm PN 25 299 (11.78) 335 (13.19) 381 (15.00) 425 (16.73) 6.6 (0.26) 251 (9.88)
250 mm PN 40 299 (11.78) 345 (13.58) 435 (17.13) 450 (17.72) 6.6 (0.26) 240 (9.45)
300 mm PN 10 327 (12.86) 370 (14.57) 457 (18.00) 445 (17.52) 6.6 (0.26) 302 (11.87)
300 mm PN 16 327 (12.86) 378 (14.88) 457 (18.00) 460 (18.11) 6.6 (0.26) 302 (11.87)
300 mm PN 25 327 (12.86) 395 (15.55) 457 (18.00) 485 (19.09) 6.6 (0.26) 302 (11.87)
300 mm PN 40 327 (12.86) 410 (16.14) 512 (20.14) 515 (20.28) 6.6 (0.26) 292 (11.48)
350 mm PN 10 354 (13.92) 430 (16.93) 534 (21.03) 505 (19.88) 7.4 (0.19) 334 (13.16)
350 mm PN 16 354 (13.92) 438 (17.24) 534 (21.03) 520 (20.47) 7.4 (0.19) 334 (13.16)
350 mm PN 25 354 (13.92) 450 (17.72) 534 (21.03) 555 (21.85) 7.4 (0.19) 334 (13.16)
350 mm PN 40 354 (13.92) 465 (18.31) 591 (23.25) 580 (22.83) 7.4 (0.19) 12.79 (325)
400 mm PN 10 379 (14.93) 482 (18.98) 610 (24.00) 565 (22.24) 7.4 (0.19) 384 (15.12)
400 mm PN 16 379 (14.93) 490 (19.29) 610 (24.00) 580 (22.83) 7.4 (0.19) 384 (15.12)
400 mm PN 25 379 (14.93) 505 (19.88) 610 (24.00) 620 (24.41) 7.4 (0.19) 384 (15.12)
400 mm PN 40 379 (14.93) 535 (21.06) 667 (26.25) 660 (25.98) 7.4 (0.19) 375 (14.75)
500 mm PN 10 437 (17.20) 585 (23.03) 762 (30.00) 670 (26.38) 7.4 (0.19) 482 (18.96)
500 mm PN 16 437 (17.20) 610 (24.02) 762 (30.00) 715 (28.15) 7.4 (0.19) 482 (18.96)
500 mm PN 25 437 (17.20) 615 (24.21) 762 (30.00) 730 (28.74) 7.4 (0.19) 482 (18.96)
500 mm PN 40 437 (17.20) 615 (24.21) 845 (33.25) 755 (29.72) 7.4 (0.19) 463 (18.21)
600 mm PN 10 495 (19.48) 685 (26.97) 914 (36.00) 780 (30.71) 7.4 (0.19) 583 (22.94)
600 mm PN 16 495 (19.48) 725 (28.54) 914 (36.00) 840 (33.07)) 7.4 (0.19) 583 (22.94)
600 mm PN 25 495 (19.48) 720 (28.35) 914 (36.00) 845 (33.27) 7.4 (0.19) 581 (22.87)
Dimensions with DIN Flanges
(2) When 2 grounding rings are specified, add 6.35 mm (0.25 in.) for 15 mm through 350 mm (½- through 14 in.) flowtubes or 12.7 mm (0.50 in.) for 400 mm
(16 in.) and larger. When lining protectors are specified, add 6.35 mm (0.25 in.) for 15 mm through 300 mm (½- through 12-in.) flowtubes, 12.7 mm (0.50
in.) for 350 mm through 900 mm (14- through 36-in.) flowtubes.
33
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
FIGURE 9. Rosemount 8711 Dimensional Drawings (0.15-inch through 1-inch line sizes)
1.8
2.6 (46)
(66)
Grounding
A Clamp
¾–14 NPT
Conduit
Connection B”
8711-1012B03B, 1012A03B
(2 places)
Flow
NOTE
Dimensions are in
C
inches (millimeters) D
See Table 15 for
variable dimensions
FIGURE 10. Rosemount 8711 Dimensional Drawings (1.5-inch through 8-inch line sizes)
1.8
2.6
(46)
(66)
B
Grounding
¾–14 NPT A Clamp
Conduit
Connection
(2 places)
8711-1012B04B, 1012A04B
Flow
C
NOTE D
Dimensions are in inches (millimeters)
See Table 15 for variable dimensions
34
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
2.69
(68.3)
4.13
(104.9)
7.19
(182.6)
Rosemount 8732C
Connector Type
Note:
The Rosemount 8714D is shipped with
8714-8714A
35
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
Flow Rate
Velocity =
Factor
Example: SI Units
Magmeter Size: 100 mm (factor from Table 17 = 492.0)
Normal Flow Rate: 800 L/min
800 (L/min)
Velocity =
492.0
36
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
37
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
Material Selection
Several liner types, electrode materials, and TABLE 22. Electrode Material
electrode types are available on Rosemount Electrode Material General Characteristics
Magnetic Flowtubes to ensure compatibility with 316L Stainless Steel • Good corrosion resistance
virtually any application. See Table 21 for information • Good abrasion resistance
on liner types, Table 22 for information on electrode • Not recommended for sulfuric
materials, and Table 23 for information on electrode or hydrochloric acids
types. Other material options not mentioned here are Hastelloy C-276 • Better corrosion resistance
available. Contact your local sales representative for • High strength
• Good in slurry applications
material selection. For further guidance on selecting
• Effective in oxidizing fluids
materials, refer to the Magnetic Flowmeter Material
Tantalum • Better chemical resistance
Selection Guide located on Rosemount.com
• Not recommended for
(document number 00816-0100-3033). hydrofluoric acid, fluosilic
acid, or sodium hydroxide
TABLE 21. Lining Material
90% Platinum - 10% Iridium • Best chemical resistance
Lining Material General Characteristics
• Expensive material
PFA • Highly chemical-resistant • Not recommended for aqua
• Excellent high temperature regia
capabilities
Titanium • Better chemical resistance
Teflon (PTFE) • Highly chemical-resistant • Better abrasion resistance
• Excellent high temperature • Good for sea water
capabilities applications
Tefzel (ETFE) • Highly chemical-resistant • Not recommended for
• Better abrasion resistance hydrofluoric or sulfuric acid
than Teflon
Polyurethane • Excellent abrasion resistance TABLE 23. Electrode Type
• Limited chemical resistance Electrode Type General Characteristics
Neoprene • Very good abrasion Standard Measurement • Costs least
resistance • Good for most applications
• Better chemical resistance
Bulletnose Electrodes • Slightly more expensive
than polyurethane
• Best option for coating
Linatex Rubber • Very good abrasion processes
resistance
Removable Electrode • Most expensive
• Limited chemical resistance
especially in acids • Better than standard
• Softer material than electrode for coating
polyurethane and neoprene processes
38
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
Ordering Information
ROSEMOUNT 8712C/U/H ORDERING INFORMATION
Availability
Model Product Description C U H
8712C Magnetic Flowmeter Transmitter • NA NA
8712U Universal Magnetic Flowmeter Transmitter NA • NA
8712H High-Signal Magnetic Flowmeter Transmitter (For use with 8707 High-Signal Flowtube only.) NA NA •
Code Transmitter Style C U H
R Remote (2-inch pipe or surface mounting) • • •
Code Power Supply Voltage C U H
03 10–30 V dc • • NA
12 115 V ac, 50–60 Hz • • •
24 230 V ac, 50–60 Hz • • NA
Code Product Certifications C U H
CE CE Marking • • NA
N0 Factory Mutual (FM) Class I, Division 2 Approval for nonflammable fluids; • • •
Canadian Standards Association (CSA) Class I, Division 2 Approval
N5 Factory Mutual (FM) Class I, Division 2 Approval for flammable fluids • • •
Code Options C U H
B6 Stainless Steel 4-bolt Kit for 2-inch Pipe Mount • • •
C1 Custom Configuration (Completed CDS required with order) • • •
C4 Analog Output Levels Compliant with NAMUR recommendations NE43, 18-January-1994, • • NA
and high alarm level(1)
CN Analog Output Levels Compliant with NAMUR recommendations NE43, 18-January-1994, • • NA
and low alarm level(1)
D1 High Accuracy Calibration [0.25% of rate from 3 to 30 ft/s (0.9 to 10 m/s)] matched flowtube • • •
and transmitter system(2)
M4 Local Operator Interface (LOI) • • •
T1 Battery-backed Totalizer • • NA
J1 CM 20 conduit adapter • • NA
J2 PG 13.5 conduit adapter • • NA
Code Quick Installation Guide (QIG) Language Options (Default is English)
YA Danish QIG • • •
YD Dutch QIG • • •
YF French QIG • • •
YG German QIG • • •
YH Finnish QIG • • •
YI Italian QIG • • •
YN Norwegian QIG • • •
YP Portuguese QIG • • •
YS Spanish QIG • • •
YW Swedish QIG • • •
Typical Model Number: 8712C R 12 N0 M4
(1) NAMUR compliant operation and the Alarm latch options are preset at the factory and can not be changed to standard operation in the field.
(2) Option Code must be selected for both flowtube and transmitter.
39
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
(1) NAMUR compliant operation and the Alarm latch options are preset at the factory and can not be changed to standard operation in the field.
(2) Option Code must be selected for both flowtube and transmitter.
40
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
(2) NAMUR compliant operation and the Alarm latch options are preset at the factory and can not be changed in the field.
(3) Option Code must be ordered for both flowtube and transmitter.
41
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
42
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
43
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
44
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
45
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
(1) Electrode options limited to two measurement electrodes or two measurement electrodes + third grounding electrode.
(2) Electrode options limited to two measurement electrodes or two measurement electrodes only.
(4) Option code limited to Liner material T, P, or F; cannot be ordered with ground rings, lining protectors AX or HX options.
(6) Grounding Rings and Lining Protectors provide the same fluid grounding function. Lining Protectors available in Teflon (PTFE) and Tefzel (ETFE) only.
(7) Sealed, welded housing (Option Code W0 or W1) required. Only available with Teflon (PTFE) lining material (Option Code T) and 316L Stainless Steel,
Hastelloy C-276, and 90% Platinum-10% Iridium electrode material (Option Codes S, H, and P). Not available with integral mount Rosemount 8712
transmitter. Sanitary connection codes A4 and A6 only available in line size code 020.
(8) Option Code must be ordered for both flowtube and transmitter.
(10) Order as a separate line item. Not available with PFA liners. Electrode code SHN only.
46
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
47
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
(1) Electrode options limited to two Hastelloy C-276 or two 90% Platinum-10% Iridium electrode material.
Cannot be ordered with ground rings or lining protectors.
(3) Grounding Rings and Lining Protectors provide the same fluid grounding function. Lining Protectors available with Teflon (PTFE) and Tefzel (ETFE) lining
material only.
(4) Option Code must be ordered for both flowtube and transmitter.
(5) Order as a separate line item (not available with PFA liners). Electrode code SHN only.
48
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
49
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
50
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
51
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
52
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
Message:
| — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | (32 characters maximum)
Enter either the Rosemount flowtube model number or select one option from each of the following groups of options:
Flowtube Model No.—————————————————————
Or:
Electrode Material: Electrode Type:
□ ★316 SST □ ★ Standard
□ Titanium □ Tantalum □ Bullet □ Standard, plus Grounding
□ Alloy-20 □ Platinum-Iridium □ Ultrasonic □ Special
□ Hastelloy C® □ Special
Flange Material: Liner Material:
□ ★Carbon Steel □ 304 SST □ ★Teflon® (PTFE)
□ Standard □ Special □ Tefzel® (ETFE) □ Ryton® □ Neoprene
□ Polyurethane □ Ceramic □ Special
□ ★ 4–20 mA, scaled pulse, and auxiliary output with simultaneous digital signal based on HART® protocol (Rosemount 8712C/U/H only)
□ ★ 4–20 mA and scaled pulse with simultaneous digital signal based on HART protocol (Rosemount 8732C only)
□ 4–20 mA and auxiliary output with simultaneous digital signal based on HART protocol (Rosemount 8732C only)
□ Burst mode of HART digital process variable
□ Multidrop Communications(1)
Choose transmitter address (1-15)(2): ———————
SPECIAL UNITS – OUTPUT INFORMATION EXAMPLE
(If applicable, complete the information on the front as shown in the examples below).
Example 1: Example 2:
User wants Barrels per day User wants Kgs per minute
(1 Barrel = 31 gallons): (Density = 1.05 Kg/Liter with 1 Kg = 0.9524 liters):
53
Product Data Sheet
00813-0100-4727, Rev MA
Rosemount 8700 Series May 2004
Fluid Description:————————————————————
Hardware Jumpers
Units = A) Write Protect □★ Off □ On
□ ★ Ft./Sec □ Ft/Min □ Ft/Hr □ Ft/d B) Simulate □★ Off □ On
□ m/Sec □ m/Min □ m/Hr □ m/d
□ Gal/Sec □ Gal/Min □ Gal/Hr □ Gal/d Flowtube Size = ————— 0.15 – 60” ★ 3”
□ m3/Sec □ m3/Min □ m3/Hr □ m3/d
3
□ cm /Sec □ cm3/Min □ cm3/Hr □ cm3/d Flowtube Calibration No. = ★ 1000005010000000
□ Ft3/Sec □ Ft3/Min □ Ft3/Hr □ Ft3/d
□ Liters/Sec □ Liters/Min □ Liters/Hr □Liters/d |—|—|—|—|—|—|—|—|—|—|—|—|—|—|—|—|
□ Igal/Sec □ Igal/Min □ Igal/Hr □ Igal/d
□ bbl*/Sec □ bbl/Min □ bbl/Hr □ bbl/d SST Flowtube Tag No.:——————————————————
□ cF/Sec □ cF/Min □ cF/Hr □ cF/d
□ lb/Sec □ lb/Min □ lb/Hr □ lb/d Damping:———————————————————————
□ kg/Sec □ kg/Min □ kg/Hr □ kg/d ★ minimum 0 seconds
□ ton/Sec □ ton/Min □ ton/Hr □ ton/d
□ ston/Sec □ ston/Min □ ston/Hr □ ston/d Density: —————————————— □ ★ 62.4 lb/ft3
*bbl = 31.5 gal US (119 liters) □ kg/m3
(required for mass units only, mass units in italics)
54
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
Descriptor: | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — | — |
(32 characters maximum)
Enter either the Rosemount flowtube model number or select one option from each of the following groups of options:
55
Product Data Sheet
00813-0100-4727, Rev MA
May 2004 Rosemount 8700 Series
Rosemount and the Rosemount logotype are registered trademarks of Rosemount Inc.
PlantWeb is a mark of one of the Emerson Process Management companies.
All other marks are the property of their respective owners.
PlantWeb and DeltaV are trademarks of the Fisher-Rosemount Group of Companies.
HART is a registered trademark of the HART Communication Foundations.
Foundation is a trademark of the Fieldbus Foundation.
Hastelloy and Hastelloy C are registered trademarks of Haynes International.
Teflon and Tefzel are registered trademarks of E.I. du Pont de Nemours &Co.
Tri-Clamp is a registered trademark of Tri-Clover, Inc. of the Alfa-Laval Group.
Foxboro and I/A Series are registered trademarks of the Foxboro Company.
ABB Fischer & Porter is a registered trademark of ABB Company.
Cover Photo: 8700_01ba.tif
¢00813-0100-4727>¤
© 2004 Rosemount Inc. All rights reserved.