ΕΛΟΤ EN 933-4

Download as pdf
Download as pdf
You are on page 1of 13
2008-10-30 ICS:91.100.15 EAOT EN 933.04 2" Exdoon = (ae EAAHNIKO MPOTYNO 7/2 See at = i, HELLENIC STANDARD - / | i SEY | mh Aoxipés yewperpiKt IioT}TW Tw apaviv - Mépog 4: Nposdiopiapés tng Hopens KOKKWY - AeiKTAS HOPONS Test for geometrical properties of aggregates - Part 4: Determination of particle shape - Shape index KAdon Twokéynonc: 4 © EAOT — EAAHNIKOZ OPFANISMOE TYTOMOIZHE AE. ‘Ayapviov 813 611145 AGhva EAOT EN 933.04 E2 EOvx6s Mpdrovos Auté eivan r0 @6}20 Emwiposns Tov eyRexpipévou Evponuixod Hpotinov EN933- 2008 cog E2qviKob Mporizov. To xpérvno avré datideta om Arrpare, 5 Pa2durc ¥ Peppavur yhseoa a6 tov Exinvixd Opyavisns Tuxoroinans A.E. Avté to Exaavixd Mporuro avrikadiotd ro EAOT EN 933.04 : 2000 National Foreword This Endorsement Sheet ratifies the approval of — European Standard EN 933-4: 2008 asa Hellenic Standard. This standard is av: , French or Ger the Hellenic Organization for Standardization S.A. This Hellenic Standard replaces ELOT EN 933.04 : 2000 EUROPEAN STANDARD EN 933-4 NORME EUROPEENNE EUROPAISCHE NORM March 2008 Ies91.100.15, ‘Supersedes EN 933-4:1030 English Version Tests for geometrical properties of aggregates - Part 4: Determination of particle shape - Shape index Essais pour diterminer les caractristiques géométviques Profvertahren fur geometrsche Eigenschalten von ‘des granulats = Pari 4: Déiermination de fa forme des CGesteinshiraungen- Te 4: Bestimmung der Koreform = ‘ganuats Coefficient de forme Komformkennzaht This European Standard was approved by CEN on 4 February 2008. CEN members are bound to comply with the CEN/CENELEC Intetnal Regulations which stipulate the conditions forgiving this European Standard ihe status of a national standaid without any elteraion. Up-to-date ists and bibliographical references conceming such naional Standards may be obtained on applcatien to fe CEN Management Centre or to any CEN member. This European Standard exists in three oficial versions (Engish, French, German). A version in any ther ianquage made by translation Under the responsibilty ofa CEN member inte ts ewn language and netfied © the CEN Managemen: Centre has the same Staus as the official vesions. CEN members are the national standards bodies cf Austria, Belgium, Bulgaia. Cyprus. Czech Repuliic. Denmark, Estona, Finland France, Germany. Greece, Hungary. eiand, lteland, tay. Lava, Linwania Luxembcurg, Malta, Netelands, Nomway. Poiand, Pongal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzeriand and Urited Kingcom, s— J EUROPEAN CONMITTEE FOR STANDARDIZATION EUROPAISCHES KOMITEE FUR NORMUNG Management Centre: rue de Stassart, 366-1050 Brussels, © 2008 CEN Al rights of exploitation in any form andy any means reserved Ret. No. EN 933-4:2008. E ‘wordwice for CEN national Members. EN 933-4:2008 (E) Contents Page ‘Scope ons. Calculation and expression of results. 9 Test report. Annex A (informative) Example of a test data sheet used for determining the shapé coarse aggregate EN 933-4:2008 (E) Foreword This document (EN 933-4:2008) has been prepared by Technical Committee CEN/TC 154 “Aggregates”, the secretariat of which is held by BSI This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2008, and conflicting national standards shall be withdrawn at the latest by September 2008 Attention is drawn to the possibiity that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 933-1999 This European Standard is one of a series of standards for tests for geometrical properties of aggregates. Test methods for other properties of aggregates are covered by Paris of the following European Standards: EN 932, Tests for general properties of aggregates EN 1097, Tests for mechanical and physical properties of aggregates EN 1367, Tests for thermal and weathering properties of aggregates, EN 1744, Tests for chemical properties of aggregates EN 13179, Tests for iller aggregate used in bituminous mixtures The other parts of EN 933 are: Part 1 - Determination of particle size distribution - Sieving metnod Part2 - Determination of particle size distribution - Test sieves, nominal size of apertures Part3 - Determination of particle shape - Flakiness index Part - Determination of percentage of crushed and broken surfaces in coerse aggregate particles Part - Assessment of surface characteristics - Flow coeffciert of aggregates Part7 - Determination of shell content - Percentage of shells in coarse aggregates Part - Assessment of fines - Sand equivalent test Part9 - Assessment of fines - Methylene blue test Part 10 - Assessment of fines - Grading of filers (zr jet sieving) According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgeria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, ‘Sweden, Switzerland and the United Kingdom. EN 933-4:2008 (E) 1 Scope This standard describes the reference method used for type testing and in cases of dispute, for the determination of the shape index of coarse aggregates. For other purposes. in particular factory production control, other methods may be used provided an appropriate working relationship with the reference method has been established. The test method specified in this European Standard is applicable to partcle size fractions d/D, where D, 2.63 mmand o = 4 mm. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the references document (including any amendments) applies. EN 9322, Test for general properties of aggregates - Part 2: Methods for reducing iaboratoy samples EN 932.5, Tests for general properties of aggregates - Part 5: Common equipment and calibration EN 933-1, Tests for geometrical proverties of aggregates - Part 1: Determination of particle size distribution - Sieving method EN 9332, Tests for geometrical proverties of aggregates - Part 2: Determination of particle size distribution - Test sieves, nominal size of apertures EN 1097-6, Tests for mechanicel and physical properties of aggregates - Part 6: Determination of the particle density and water absorption 3 Terms and definitions For the purposes of this document. the following terms and definitions apoly. 34 aggregate size designation of aggregate in terms of lower (d) and upper (D) sieve sizes, expressed as d/D NOTE This designation acceots the presence of some particles which will be retained on the upper sieve (oversize) and some wich will pass the lower sieve (undersize}, 32 particle size fraction iD, fraction of an aggregate passing the larger (D) of two sieves and retained on the smaller (d) 3.3 test portion sample used asa whole in asingle test 34 constant mass Successive weighings after drying al least 1 h apart not differing by more than 0,1 % NOTE In many cases constant mass can be achieved alter @ test portion has been dried for a pre-determined period in 2 spediied oven (see 5:5) a! (110 # 5) °C. Test laboravries can determine the time required to actieve constant mass for spedfic types and sizes of sample dependent upon the drying capacity of he even used, EN 933-4:2008 (E) 35 particle length L maxmum dimension of a particle as defined by the greatest distance between two paralel panes tangential to. the particle surface 36 particle thickness E minimum dimension of a partcle as defined by the least distance between two parallel planes tangential to the particle surfece 4 Principle Individual particles in a sample of coarse aggregate are classified on the bas's of the ratio of their length L to thickness E using a particle side gauge wnere necessary. The shape index is calculated as the mass of particles with a ratio of dimensions L/E more than 3 expressed as a percentage of the total dry mass of particles tested. 5 Apparatus 5.1 All apparatus, unless otherwise stated, shall conform to the general requirements of EN 932-5. 5.2 Particle slide gauge, an example of which is shown in Figure 1 5.3. Test sieves, with nominal size of apertures as speciied in EN 933-2. 5.4 Tightly fitting pan and lid. for the sieves. 5.5 Ventilated oven, thermostatically controlled to maintain (110 5) °C, or other suitable equipment for drying the aggregates, ift does not cause any particle size breakdown 5.6 Balances or scales, of sutable capacity, readable to 0,1 % of the mass to be weighed. 5.7 Trays 5.8. Sieving machine, (optonal) EN 933-4:2008 (E) Dimensions in millimetres Figure 1 - Example of a particle slide gauge 6 Preparation of test portion The sample shall be reduced in accordance with the requirements of EN 932-2. Drythe sample at (110 +5) °C to constant mass. Sieve on appropriate test sieves with sufficient vigour to ensure complete separation of particles greater than 4mm. Discard the partices retained on the 63 mm test sieve and those passing the 4 mm test sieve. If necessary further reduce the sample in accordance with EN 932-2 to produce a test portion. Record the mass of the test portion as Mz EN 933-4:2008 (E) ‘The mass of the test portion shall be as specified in Table 1 Table 1 - Mass of test portions Upper aggregate size D Test portion mass (minimum) mm kg 63 45 32 6 16 1 8 oa NOTE 1 For the other upper agoregate sizes D, appropriate test portion masses ‘may be interpolated rom those given in Tale 1 NOTE2 For aggregates of particle density less than 200 Mafm® or more than 3,00 Nigitn’ in accordance with EN 1097-6 an appropriate correction should be ‘applied to the test portion masses given in Table 1 based on the density ratio, in ‘tder 10 produce a test portion of approximately the same volume as those for aggregates of normal density Sample reduction shall yield a test portion with a mass larger than the minimum but not of an exact predetermined value. 7 Procedure 7A General The test shall be carried out on each particle size traction d/D, where D< 2d. Test portions from samples for which D > 2d shall be separated into particle size fractions d/D, where D, < 24 during the subsequent test procedure 7.2. Test portions where Ds 2d Separate the particle size fraction d/D, where D, < 2d, from the test portion by sieving in accordance with EN 933-4 Discard any partcles smaller than d, and any larger than D. Record the particle size fraction d/D, thats to be tested and record the mass of the particle size fraction d/D, as M Assess the length Land thickness E of each particle using a particle slide gauge where necessary and set aside those particles which have a dimensional ratio L/E> 3. These particles are classified as non-cubical NOTE The number of particles requiring individual classification using the gauge can be reduced by a prelimnary separation of particles with a L/Erati significantly different from 3, Weigh the non-cubical particles and record their mass as M. EN 933-4:2008 (E) 7.3. Test portion where D> 2d ‘Separate the test portion into particle size fractions 0/D, where D, = 2d, by sieving in accordance with EN 933-1. NOTE 1 Test sieves of appropriate aperture sizes from the following series should be used, viz. 4 mm; 5.6 mm; 8 mm 40mm; 14,2 mm; 12,5 mm; 16 mm, 22.4 mm; 31,5 mm; 45 mm; 63 mm; and the values of d, and D, of each size fraction tested should be recorded in the test report Record the mass of each particle size fraction (IM) and calculate and record the percentage by mass of each Parricle size fraction d/D,to the test portion mass M, as V, Discard any size fraction d/D, which comprises less than 10 % of Mo, NOTE 2 If any remaining size fraction a/D, contains less than 100 particles, it should if required, be recorded in the tes! report, Any size fraction d/D, which contains an excessive number of particles can be further reduced in accordance with EN 932-2, but after such reduction at least 100 particles of thet size fraction shall remain Record the mass of particles to be tested in each remaining particle size fraction d/D, as My. Assess the length L and thickness E of each particle using a particle side gauge where necessary and set aside those particies in each size fraction which have a dimensional ratio LiE > 3. These particles are classified as non-cutical. Record the mass of non-cubical particles in each of these size fractions d/D, as Ma. 8 Calculation and expression of results Calculate the shape index (Si) in accordance with the following equation: ST =(M/M,)x100 a where M, isthe mass ofthe test portion, in grams; M, _ isthe mass of the non-cubical particles, in grarrs. Record the shape index to the nearest whole number. EN 933-4:2008 (E) 8.2. Test portions where D > 2d 8.24 e fractions not reduced Calculate the shape index (Si) in accordance with the following equation: EM 100 e@ where 2M, isthe sum of the masses of the size fractions tested, in grams; 3Ma_ isthe sum of the masses of the nor-cubical partes in each of the size fractions tested, in grams. Record the shape index to the nearest whole number. 8.2.2 Reduced size fractions Calculate the percentage of non-cubical particles in each size fraction tested and record as Si. Calculate the weighted mean percentage of non-cubical particles (Si) in accordance with the ‘ollowing equation SI) AAS @) where isthe percentage by mass of particle size fraction i in the sample tested; Si, isthe percentage by mass of non-cubical particlas in patticle size fraction i Record the weighted mean percentage of non-cutical particles to the nearest whole number. 9 Test report 9.1 Required data The test report shall include the following information. a) reference to this European Standard (EN 933-4:2008); ) identification of the laboratory; ©) identification of the sample; d) shape index (S/) to the nearest whole number: 2) values of d, and D, of particle size fractions tested; EN 933-4:2008 (E) ) sample reception date. 9.2 Optional data The test report can include the folowing information. a) name and location of the sample source; b) description of material end of sample reduction procedure; ©) mass of test portion (Mao) d) mass of size fraction(s) tested (Ms or Mu): ) mass of non-cubical particles in size fraction(s) tested(M, or Ma) ) any size fraction d/D, with less than 100 paricles; 9) sampling certificate. if available: h) date of test, 10 EN 933-4:2008 (E) Annex A (informative) Example of a test data sheet used for determining the shape index of coarse aggregate EN 933-4 Laboratory Identification of the sample: Date Operator 9 Particle size fraction d/D, Mass M, Mass Mz Shape index S1% where 0, 5 2a) = (Mz) x 100 mm 9 g tothe nearest whole number NOTE When a partie size faction o/D, has been reduced an appropriate test data sheet can be used and the weighted mean valuee caleulates ac epectiod in 8.2 1

You might also like