Function diagrams

Generic functions
• A function: Delay on energisation • AM function: Delay on energisation • H function: Timing on energisation - • P and Pe functions: Impulse counter (delay on)
1 relay Pulse output (adjustable)
U : Supply Latching during the time delay. U : Supply P function:
1 relay
R :O  utput relay Single shot timing which starts R :O  utput relay Timing starts on energisation.
On energisation, the output relay
or load on energisation. or load "R" (or the load) changes state, and At the end of timing, the output
T : Timing T : Timing stays there for the whole duration of relay "R" (or the load) changes
state for approximately 500 ms.
∞ : Infinity ∞ : Infinity the time delay and drops out at the
C (Y1) : Command • Ac function: Timing after closing and opening C (Y1) : Command end of the single shot cycle. Pe function:
of control contact On energisation.
1 relay • Ht function: Delay on energisation with memory At the end of timing, the output
After energisation, closing of the • AMt function: Delay on energisation 1 relay relay "R" (or the load) changes
control contact results in starting state for approximately 1 s.
of the time delay T. 
Latching during and after Adds up the total opening time
Output relay "R" (or the load) the time delay. of a contact.
changes state at the end of On energisation, the output relay
this time delay. After opening of "R" (or the load)
contact C (Y1), relay "R" drops out changes state, and stays there for
after a second time delay T. the whole duration of the time delay
and drops out at the end of the • Pt function: Impulse counter (delay on)
single shot cycle.
 elay on energisation
• Ad function: D
• B function: Timing on impulse (one shot) - • K function: Delay on de-energisation
Adds up the total opening time
of a contact.
(cannot be reset) At the end of timing, the output is
1 relay
Shaping (cannot be reset) True delay off
excited for approximately 500 ms.

After energisation, a control pulse 1 relay
After energisation, an impulse
(without auxiliary power supply)
or latching contact starts timing. 1 relay
At the end of timing, the output (≥ 50 ms) or a latching contact
On energisation, the output relay
is excited. The output will be reset causes a change in state of the
"R" (or the load) changes state.
when a new control pulse or output relay "R" (or the load)
On de-energisation timing starts • Q function: "Star-delta" starting
latching contact occurs. which drops out at the end
and the relay "R" will only drop out
of timing.
at the end of this time delay.
On energisation, the "star"
• Bw function: Pulse output (adjustable) • L function: Asymmetrical flashing contact closes instantaneously
and timing starts.
1 relay 1 relay At the end of timing the Ti "star"
 ingle shot flip-flop
• Ah function: S On closing and opening Repetitive cycle with two times
contact opens. After a pause
(cannot be reset) of the control contact C (Y1), of 40 to 100 ms the "delta" contact
which can be set independently.
2 timers or the output relay "R" (or the closes.
2 relays including
Each time delay alternates with a
After energisation, a control pulse load) changes state for as long 2 timers or different state of the output relay
1 instantaneous
or latching contact starts timing. as the time delay lasts. 2 relays including "R" (or the load).
At the end of timing, the output is 2 timers or 1 instantaneous
excited. The time delay is then 2 relays including 1 instantaneous Note: The cycle starts with
reset. At the end of this new time the relay "R"in the rest position. • TL function: Impulse relay
delay, the output reverts to its initial
value.  fter energisation, a control pulse
A
• Li function: Asymmetrical flashing or latching contact closes the
1 relay relay. A second control pulse
opens the relay.
• C function: Timing after impulse Repetitive cycle with two times
• At function: Timing on energisation True delay off which can be set independently.
with memory (without auxiliary power supply)
1 relay
Adds up the opening time
1 relay • N function: "Safe-guard"
After energisation, closing of the • Tt function: Timed impulse relay
of a contact. control contact C (Y1) results in
On the first control pulse,
the change of state of output relay After energisation, a control pulse
Output relay "R" (or the load) the output is excited.
"R" (or the load). or latching contact closes the relay
changes state at the end of timing. If the interval between two
Timing will only start when this and starts timing.
impulses is longer than the timing
contact opens. The relay opens at the end of timing
value, this occurs normally and the
• A1 function: Delay on energisation output relay "R" (or the load) or on a second control pulse.
will change state at the end of
• D or Di functions: Symmetrical flashing timing. Otherwise, relay "R" stays
1 timer Repetitive cycle which alternately sets the output relay "R" in its original state until the
1 instantaneous relay (or the load) to operating and rest position for equal periods condition is fulfilled.
of time.
• O function: "Delayed safe-guard"
1 relay  iming after pulse on control contact
• W function: T
D function: On energisation, a first timer
The cycle starts with relay runs and the output relay "R" After energisation, opening of the
• A2 function: Delay on energisation "R" in rest position. (or the load) changes state. control contact results in a change
On the appearance of a control in the state of output "R" (or the
1 relay
pulse, relay "R" returns to its initial load) and timing starting.
2 timers. Di function: position and stays there as long as
The cycle starts with relay the time interval between 2 impulses is less than the timing value.
"R" in operating position. Otherwise, relay "R" will change state at the end of timing.