Method of Measurements For Sewer Networks-3

The Specification, Bills of Quantities and Typical Details
For Water and Wastewater Networks Method of Measurements for Sewer Networks
The Specification, Bills of Quantities and

Typical Details for Water and Wastewater
Networks
Method of Measurements – Sewer Networks
Document Number: 00_TES_TM_004.01
This Issue Date 24/01/2021 11/06/1442 (H)
UPDATING
The BEE Department or the document owner will issue updates to all registered holders of each “hard
copy” of this document. The registered holder will be responsible for updating the document by
replacing pages or sections as instructed. Printed copies will automatically assume as “unmaintained”
status.
Copyright Notice ©Copyright 2020
All rights reserved. This is the property of National Water Company “NWC” The contents of this
document, either in full or in part, are not allowed to be copied in any form or used by anyone outside
NWC unless specifically authorized in writing by the document owner of other authorized representative
of NWC
Issue Date 24/1/2021

Table of Contents
PREAMBLE ......................................................................................................................... 1
SCOPE AND BASIS OF PAYMENT .................................................................................... 1
Scope of Payment................................................................................................................ 1
Basis of Payment ................................................................................................................. 1
DIVISION 1 GENERAL REQUIREMENTS ........................................................................ 3
011100 SCOPE AND CONTROL OF WORKS ........................................................... 3
013500 SAFETY PRECAUTION MEASURES ............................................................ 3
014300 CONTROL OF MATERIALS AND STANDARDS FOR SAMPLING AND
TESTING ........................................................................................................ 3
DIVISION 26 ELECTRICAL WORK ..................................................................................... 4
260513 MEDIUM VOLTAGE CABLES & 260519 LOW VOLTAGE ELECTRICAL
POWER CONDUCTORS AND CABLES........................................................ 4
260526 GROUNDING AND BONDING FOR ELECTRICAL SYSTEMS ..................... 5
261200 MEDIUM VOLTAGE TRANSFORMERS ........................................................ 6
261300 MEDIUM VOLTAGE SWITCHGEAR .............................................................. 7
262413 SWITCHBOARDS & 262416 PANELBOARDS .............................................. 8
262419 MOTOR CONTROL CENTERS ..................................................................... 9
263100 PHOTOVOLTAIC ENERGY SYSTEM.......................................................... 10
263213 PACKAGED ENGINE GENERATORS ......................................................... 11
263353 STATIC UNINTERRUPTIBLE POWER SUPPLY (UPS) .............................. 12
263533 POWER FACTOR CORRECTION CAPACITORS ....................................... 13
263600 TRANSFER SWITCHES .............................................................................. 14
264313 SURGE PROTECTIVE DEVICES ................................................................ 15
265100 INTERIOR LIGHTING .................................................................................. 16
265600 EXTERIOR LIGHTING & 265614 SOLAR POWERED EXTERIOR LED
LIGHTING .................................................................................................... 17
DIVISION 31 EARTHWORK .............................................................................................. 19
311000 SITE CLEARING .......................................................................................... 19
1. Site Preparation ............................................................................................................ 19
2. Removal of Obstructions and Relocation of Utilities ..................................................... 19
312000 EARTH MOVING .......................................................................................... 20
1. Geotextiles ................................................................................................................... 20
2. Excavation and Backfilling for Structures...................................................................... 21
4. Excavation and Backfilling for Utility Trenches ............................................................. 22
5. Filling and Backfilling .................................................................................................... 23
6. Drainage and Filter Materials........................................................................................ 25
313223.17 PROBING AND GROUTING ........................................................................ 27
1. Probing ......................................................................................................................... 27
00_TES_TM_004.01
2. Grouting........................................................................................................................ 27
313223.18 GROUND IMPROVEMENT .......................................................................... 28
313613 GABION BOXES .......................................................................................... 29
313716.20 STONE RIPRAP ........................................................................................... 30
DIVISION 32 EXTERIOR IMPROVEMENTS ..................................................................... 31
32116.16 AGGREGATE SUB-BASE COURSE ........................................................... 31
321216 ASPHALT PAVING ...................................................................................... 33
321400 UNIT PAVING .............................................................................................. 35
DIVISION 33 UTILITIES..................................................................................................... 37
330507.36 MICRO TUNNELING AND PIPEJACKING................................................... 37
333111 PUBLIC SANITARY SEWERAGE GRAVITY PIPING & 333123 SANITARY
SEWERAGE FORCE MAIN PIPING ............................................................................ 38
1 Pipes, Fittings and Accessories .................................................................................... 38
2 Valves and Accessories on Force Mains ...................................................................... 40
3 Manholes, Inspection and Valve Chambers ................................................................. 42
4 Protective Coatings ...................................................................................................... 43
5 Connecting Works to Existing Networks ....................................................................... 44
6 Relocation of Existing Utilities....................................................................................... 44
DIVISION 40 – PROCESS INTERCONNECTIONS........................................................... 45
406000 - PROCESS CONTROL AND ENTERPRISE SYSTEM ........................................ 45
1 Process SCADA System .............................................................................................. 45
2 Process Controllers ...................................................................................................... 46
3 Process Control / Telemetry Wiring .............................................................................. 47
4 Process Field Instrumentation ...................................................................................... 47
00_TES_TM_004.01
PREAMBLE
PREAMBLE
SCOPE AND BASIS OF PAYMENT
Scope of Payment
The Contractor shall consider that all items shown in contract and corresponding to
BOQ shall include full payment for all labour, material, tools, equipment,
organizational costs, insurance, shipping, duties and other charges, overheads, profit,
royalties, transport, handling, setting up, payments to others for land or use of land or
damage to property of others, all temporary works, incidental works necessary for
proper completion of the Works and which shall not be paid for directly but shall be
considered as subsidiary works the costs of which shall be deemed to be included in the
Contract Rates and Amounts for related Pay Items.
Basis of Payment
A Quantities determined in accordance with this Standard Method of Measurement for

sewer works shall be paid for at the respective Contract Rates and Amounts and
Contract rates per unit of measurement, for each of the particular Pay Items shown in
the Bills of Quantities, which rates and amounts shall be full compensation for
furnishing everything necessary for the proper execution, completion of the Works.
B Wherever any "Measurement" rule, as contained in this Standard Method of

Measurement for sewer works, states that no measurement shall be made for direct
payment of works prescribed in a particular Section of the Specification, performance
of such works shall not be paid for directly but shall be considered as subsidiary works
the costs of which shall be deemed to be included in the Contract Rates and Amounts
for related Pay Items.
C The measurement rules contained in this Standard Method of Measurement for sewer
works may not cross reference to all the Sections of the Specification. Wherever these
rules are absent, the works prescribed in those particular Sections of the Specification
shall not be measured for direct payment, unless shown as Pay Items in the Bills of
Quantities, but shall be considered as subsidiary works the costs of which shall be
deemed to be included in the Contract Rates and Amounts for related Pay Items.
D Unless shown as Pay Items in the Bill of Quantities, all other works prescribed in the
various Sections of the Specification, shall not be measured for direct payment, but
shall be considered as subsidiary works the costs of which shall be deemed to be
included in the Contract Rates and Amounts for related Pay Items.
E In the case of works or drawings details that are not mentioned in BOQ, these works
and details shall be considered included in other items of BOQ.
00_TES_TM_004.01 Preamble - Page 1 of 48

F All length measurements shall be horizontal to the nearest 1/100m. All area
measurements shall be the nearest 1/100m2. Volumetric measurements shall be to the
nearest 1/100m3.
G Abbreviations:
L.m. = Linear meter m3 = meter cube
m2 = meter square L.s. = Lump sum
Nr = Number
All rates and amounts shall be quoted in Saudi Riyals (S.R).
00_TES_TM_004.01 Preamble - Page 2 of 48

DIVISION 1:
GENERAL REQUIREMENTS
DIVISION 1 GENERAL REQUIREMENTS
011100 SCOPE AND CONTROL OF WORKS
1.01 Unless shown as Pay Items in the Bill of Quantities, all works, material sources,
inspections and all other requirement related to setting out the works, provide necessary
documentation, requirements related to temporary works, temporary facilities,
contractor’s plant and equipment and all other requirements related to the scope and
control of works as prescribed in Section 011100 and its related appendices of the
Specification, shall not be measured for direct payment, but shall be considered as
subsidiary works, the costs of which shall be deemed to be included in the Contract
Rates and Amounts for related Pay Items.
013500 SAFETY PRECAUTION MEASURES
1.01 Unless shown as Pay Items in the Bill of Quantities, all works, material sources,
inspections and all other requirement related to safety precautions measures as
prescribed in Section 013500 of the Specification, shall not be measured for direct
payment, but shall be considered as subsidiary works, the costs of which shall be
deemed to be included in the Contract Rates and Amounts for related Pay Items.
014300 CONTROL OF MATERIALS AND STANDARDS FOR SAMPLING AND

TESTING
1.01 Unless shown as Pay Items in the Bill of Quantities, sampling, testing, and retesting,
material sources, quality requirements, certificates' inspections, storage and handling
requirements, standard specifications to be furnished, and all other works prescribed in
Section 014300 of the Specification, shall not be measured for direct payment, but shall
be considered as subsidiary works, the costs of which shall be deemed to be included
in the Contract Rates and Amounts for related Pay Items.
00_TES_TM_004.01 010000 - Page 3 of 48

DIVISION 26:
ELECTRICAL WORK
DIVISION 26 ELECTRICAL WORK
260513 MEDIUM VOLTAGE CABLES & 260519 LOW VOLTAGE

ELECTRICAL POWER CONDUCTORS AND CABLES
1.01 Each kind of cable is given separately (except where required to be included with other
items), stating the type, size and method of installation.
1.02 Cables are given in linear meters, measured the net length.
1.03 Rates for cables are deemed to include the costs of:
conduits, fittings, draw wires and the like (except where conduit work is required to be
measured separately),
cable sleeves where required and with size and type as shown on the drawings,
cable connectors and cable joints (where permitted) including joint boxes, sealing
boxes, shrouds and the like, materials and heat for making the joints,
allowance in cable length for cables entering fittings and accessories, equipment or
control gear,
necessary components and accessories for fixing cables on walls, ceilings and on cable
trays.
Pay Item Unit of Measurement
Medium voltage cables Linear meter (Lm)
Low voltage electrical power conductors and cables Linear meter (Lm)
00_TES_TM_004.01 260513 & 260519 - Page 4 of 48

260526 GROUNDING AND BONDING FOR ELECTRICAL SYSTEMS
1.01 Each kind of earthing system is given separately, stating the type and details, as
appropriate:
1.02 Earthing conductors are given in linear meters.
1.03 Earth pits are given in number.
1.04 Earth rods are given in number.
1.05 Clamps are given in number.
1.06 Earthing test links are given in number.
1.07 Rates of measured work are deemed to include the costs of a complete system,
excluding protective earthing conductors run with branch circuit wiring and protective
earthing cables run with main and sub-feeders which are required to be measured
separately or included with other items.
earthing loops conductors, conduits for earthing conductors, lattices, pits, electrodes,
connectors, clamps, earthing conductors from earthing loops, earth lattices, exothermic
welding to these earthing loops and rebars, and electrical identification as required by
specifications,
bonding and connection between earthing networks, at various levels of rock cut line,
where applicable,
bonding to all metallic equipments as per specification,
calculating / measuring earth fault loop impedance and checking its compliance with
specifications.
Earthing Conductors Linear meter (Lm)
Earth Pits Number (Nr)
Earth Rods Number (Nr)
Clamps Number (Nr)
Earthing Test Links Number (Nr)
00_TES_TM_004.01 260526 - Page 5 of 48

261200 MEDIUM VOLTAGE TRANSFORMERS
1.01 Each kind of transformer is given separately. Type, reference and ratings of
transformers are stated in descriptions, where appropriate.
1.02 Transformers are enumerated.
1.03 Rates for measured work are deemed to include the costs of:
termination of incoming and outgoing cables including cable terminal boxes and
accessories,
all auxiliaries, instruments, sensors, controls and necessary protection,
neutral earthing resistances where applicable,
surge arresters unless included under MV switchgear,
supports required for installation of transformers on bases and/or trenches,
interconnection control cables and other accessories for interface with other systems
and the like,
concrete bases and/or fence or external protection (bollards, etc) for transformers
(where not forming an integral part of the building structure),
spare parts, tools and instruments.
MV/LV Transformer Number (Nr)
00_TES_TM_004.01 261200 - Page 6 of 48

261300 MEDIUM VOLTAGE SWITCHGEAR
1.01 Each kind of medium voltage switchgear and ring main unit is given separately. Type,
number and arrangement of cubicles, and switchboard references are stated in
descriptions or shown on the Drawings.
1.02 Rates for Medium voltage switchgears are deemed to include the costs of:
AC/DC power supply for switchgear control and operation, including charger, batteries,
DC panels, etc.,
all auxiliaries, instruments, sensors, controls and necessary protection,
surge arrestors,
accessories,
interconnection control cables and other accessories for interface with remotely control
systems and the like as shown in the specifications,
supports required for installation of switchgear on bases and/or trenches,
concrete bases or raised floor, where not forming an integral part of the building
structure,
spare parts tools and instruments.
RMU/MVSG Number (Nr)
00_TES_TM_004.01 261300 - Page 7 of 48

262413 SWITCHBOARDS & 262416 PANELBOARDS
1.01 Each kind of switchboards and panelboards is given separately, stating the reference of
equipment.
1.02 Switchboards and panelboards are enumerated.
termination of incoming and outgoing cables to equipment including cable glands,

terminations and accessories,
fixing and support structures and materials required for installation of wall or floor
mounted equipment as indicated,
all components housed within the switchboard or panelboard,AC or DC power supply

for switchgear control and operation,
interconnection control cables and other accessories for interface with other systems
and the like,
spare parts, tools, and instruments,
Switch Board Number (Nr)
Panelboard Number (Nr)
00_TES_TM_004.01 262413 & 262416 - Page 8 of 48

262419 MOTOR CONTROL CENTERS
1.01 Each kind of motor control center/panel is given separately, stating the reference of
equipment.
1.02 Motor control centers/panels are enumerated.
1.03 Combination starters are each given separately stating rating, type, reference of
equipment and are enumerated.
1.04 Rates for motor control center/ motor control panel are deemed to include the costs of:
motor starters, variable frequency drives, contactors, circuit breakers, switches, lamps,
internal wiring/cabling and all other accessories as described in specifications, shown
on the Drawings and/or reasonably required for the execution, commissioning,
operation and performance of motor control center/motor control panel,

mounted equipment as required,
interconnection control cables, instruments, transducers, auxiliary contacts, necessary

interface devices and all other accessories for interface with other systems as described
in specifications or as shown in drawings,
AC or DC power supply for control and operation,
power supply to all relevant auxiliary devices,
spare parts, tools and instruments,
harmonic analysis, where required.
MCC/MCP Number (Nr)
00_TES_TM_004.01 262419 - Page 9 of 48

263100 PHOTOVOLTAIC ENERGY SYSTEM
1.01 Each kind of the below systems is given separately:
PV modules
Aluminum mounting structures
DC cables,
DC combiner boxes
Protection and Isolation devices
PV monitoring & control system
String Inverters
AC cables
1.02 Rates for measured work are deemed to include, but not limited to the following:
PV modules (laminates in mounting frames).
DC string combiner and monitoring boxes
Inverters.
Mounting structures.
Cabling including trays, conduits, fitting and raceways
Distribution panels including all protection devices
Metering
PV modules Area (m2)
Aluminum mounting structures Area (m2)
DC cables Linear meter (Lm)
DC combiner boxes Number (Nr)
Protection and Isolation devices Number (Nr)
PV monitoring & control system Number (Nr)
String Inverters Number (Nr)
AC cables Linear meter (Lm)
00_TES_TM_004.01 263100 - Page 10 of 48

263213 PACKAGED ENGINE GENERATORS
1.01 Each kind of emergency power plant is given separately.
1.02 The following components are each given separately and are enumerated:
generating sets (stating rating and speed),
daily fuel tank system (stating generating plant served),
filters (unless otherwise integrated within the silencers) (stating type).
1.03 Rates for generating sets are deemed to include the costs of:
cooling system including radiators, piping, make-up tanks and accessories,
starting system (compressed air, battery, etc.),
outdoor generator set enclosure,
exhaust system including piping, silencers, insulation, etc.,
Noise control measures including inlet and outlet attenuators, wall lining and any other
measures required to meet the specified noise criteria,
control and instrumentation panel/cubicle and interconnecting cables, wires and

accessories,
supporting structures and fixing materials,
termination of cables to generating sets and control panels including cable terminal
boxes and accessories,
spare parts for 1000 hours running and not less than the duration indicated in the
Specifications,
tools and instruments.
1.04 Rates for the fuel tank systems are deemed to include the costs of:
fuel tanks,
piping, fuel transfer pumps and related accessories from fuel tank to generator.
Diesel generator set Number (Nr)
Fuel system Number (Nr)
00_TES_TM_004.01 263213 - Page 11 of 48

263353 STATIC UNINTERRUPTIBLE POWER SUPPLY (UPS)
1.01 Each kind of static UPS system is given separately, stating the capacity, autonomy and
reference.
1.02 Static UPS systems are enumerated.
UPS units (single; number as per single line diagrams and/or specifications), automatic
static bypass transfer switch, external bypass switch, input/output isolation transformer,
and output transformer where applicable or required,
batteries, battery chargers, battery cabinets and racks and interconnecting cables and
accessories,
accessories,
remote control and indicating panels and interconnects,
interconnection control cables and other accessories for interface as shown in the
specifications,
static transfer switch,
spare parts, tools and instruments, where specified.
UPS Number (Nr)
00_TES_TM_004.01 263353 - Page 12 of 48

263533 POWER FACTOR CORRECTION CAPACITORS
1.01 Power factor correction capacitors systems are enumerated stating the rating and
reference.
detuned capacitors,
protective devices, fuses and relays,
discharge resistors,
instrumentations and controls including step contactors,
termination of incoming and outgoing cables,
interconnection control cables and other accessories for interface with other systems,
emergency power plant and the like,
fixing and supports,
spare parts, tools and instruments where specified.
PFC Number (Nr)
00_TES_TM_004.01 263533 - Page 13 of 48

263600 TRANSFER SWITCHES
1.01 Each kind of automatic transfer switch is given separately, stating the rating and
reference of equipment.
1.02 Automatic transfer switches are enumerated.
1.03 Rates for automatic transfer switches are deemed to include the costs of:

mounted equipment as indicated,
AC or DC power supply for control and operation,
instruments and controls,
control inter-cabling between the automatic transfer switch and sources as required per
specifications and/or as shown on drawings,
enclosure appropriate for the installation and as specified,
spare parts, tools, and instruments.
ATS Number (Nr)
00_TES_TM_004.01 263600 - Page 14 of 48

264313 SURGE PROTECTIVE DEVICES
1.01 Surge protective devices are not given separately and the costs are deemed to be
included in the rates for measured work for protected electrical and telecommunication
equipment.
00_TES_TM_004.01 264313 - Page 15 of 48

265100 INTERIOR LIGHTING
1.01 Each kind of lighting fixture is given separately, stating the type.
1.02 Lighting fixtures are enumerated (except for linear lighting systems, which are given in
linear meters).
1.03 Lighting fixtures fed from central battery system are enumerated (except for linear
lighting systems, which are given in linear meters).
1.04 Rates for lighting fixtures are deemed to include:
outlets,
wires including protective earthing conductors, conduits, trunking and other raceways
and fittings from outlet back to upstream outlet or to final branch circuit panel board,
control gear / drivers, transformers and the like,
capacitors for conventional ballasts, if any,
batteries for self-contained fixtures,
lamps / light sources,
installation including fixation, suspension rods and supporting material,
spare parts, as specified.
1.05 Rates for lighting fixtures fed from central battery system are deemed to include:
outlets,
fire resistant wires including protective earthing conductors, conduits, trunking and
other raceways and fittings from outlet back to upstream outlet or to final branch circuit
panel board,
AC/DC electronic ballast, control gear / drivers, transformers and the like,
lamps / light sources,
installation including fixation, suspension rods and supporting material,
spare parts, as specified.
Lighting Fixture Number (Nr)
Linear LED Strip Linear meter (Lm)
00_TES_TM_004.01 265100 - Page 16 of 48

265600 EXTERIOR LIGHTING & 265614 SOLAR POWERED EXTERIOR LED

LIGHTING
1.01 The following components related to exterior lighting are each given separately.
Exterior lighting fixtures (where required to be measured separately),
Solar lighting columns,
1.02 Exterior lighting fixtures are enumerated stating type, details and reference as
appropriate.
1.03 Lighting columns / poles are enumerated, stating type, details and reference as
appropriate.
1.04 Rates for exterior lighting fixtures, where measured separately are deemed to include:
earthing and lightning system, as applicable,
relevant connections accessories,
hermatically sealed category B capacitors,
terminals, lugs, protective devices and boxes,
lamps/light sources, ballasts/drivers, transformers, ignitors, etc. and all luminaire

components,
junction boxes,
internal wiring from junction box to and between luminaires components,
spare parts (lamps, control gear, etc.) as specified,
1.05 Rates for solar lighting columns / poles are deemed to include:
lighting column / pole, supporting bracket/arm, template, fixation plate, bolts and nuts,
caps, handholes, etc.,
earthing and lightning system, as applicable,
cabling inside column,
all relevant poles accessories and fittings,
PV modules (laminates in mounting frames),
Inverters,
mounting structures,
Internal cabling including conduits, fitting and raceways,
00_TES_TM_004.01 265600 & 265614 - Page 17 of 48

Control panels including all protection devices,
complete battery system and enclosures,
all interfaces for the remote lighting control and monitoring system,
column concrete base (foundation) and associated cables draw-pit and other related
civil works, as per the approved high mast/column detail,
Soil replacement to improve the subgrade under foundations,
Rock bolting of foundations on hard rock,
Riprap around poles in sand dune areas,
Piles integrity and cross-hole sonic testing,
cost of any alteration in the column specification or foundation dimensions due to

Contractor’s alternatives.
Exterior Lighting Fixture Number (Nr)
Solar Lighting Pole Number (Nr)
00_TES_TM_004.01 265600 & 265614 - Page 18 of 48

DIVISION 31:
EARTHWORK
DIVISION 31 EARTHWORK
311000 SITE CLEARING
1. Site Preparation
1.01 Clearing the site generally is given as an item.
1.02 Work is deemed to include:
removing trees and tree stumps, and grubbing up roots; clearing site vegetation,
including but not limited to shrubs, grass, hedges, bushes, scrub, undergrowth and the
like, and grubbing up roots,
removing general trash, debris and rubbish,
stripping topsoil as required and disposing of as directed, including multiple handling,

depositing in stockpiles or spreading and levelling on site, or removing from site,
removing all surplus and unsuitable materials arising from site clearing operations, and
legally disposing of off-site, including multiple handling, providing tips and paying all
fees and associated costs,
filling voids and depressions where further excavation or earthwork is not indicated or
required,
clearing and grubbing for the ROW.
Site clearing Square meter (m2)
2. Removal of Obstructions and Relocation of Utilities
2.01 Removal of Obstructions:
Pursuant to clause 3.3 under the specifications Section 011100 "Scope and control of
works”, no measurement or payment shall be effected against any removal of
obstructions and utilities existing underground redundant utilities and / or culverts and
other obstructions.
2.02 Relocation of Existing Utilities:
Refer to clause 6 under section 333111 and 333123
00_TES_TM_004.01 311000 - Page 19 of 48

312000 EARTH MOVING
1. Geotextiles
1.01 Each kind of fabric is given separately, as specified:
subsurface drainage geotextile (non-woven),
separation geotextile (woven).
1.02 Fabrics are given in square metres measured over the area covered. No deduction is
made for voids not exceeding 1.00 m2.
1.03 No payment will be made for fabrics replaced because of waste contamination, damage,
repair, or due to contractor fault or negligence.
1.04 Overlaps for seaming shall not be measured for payment, but shall be considered as part
of the work.
material and associated equipment and operation used in laps, seams, or extra length,
or protection of works,
securing pins and associated material, equipment, and operations,
horizontal, sloping, vertical and curved work,
work of any width,
extra material for lapping and jointing,
welding, cutting, and repairing defective work,
cushioning layer of sand or gravel,
material and seam testing, non-destructive testing, electrical testing, and all other tests,
all plant, labour, material, and equipment and performing all operations necessary for
the complete and satisfactory installation,
cost for quality assurance (QA) team and third party construction quality assurance
(CQA) team, or any other agencies that will be required for works completion in
accordance with contract specifications.

Subsurface drainage geotextile (non-woven) Square meter (m2)
Separation geotextile (woven) Square meter (m2)
00_TES_TM_004.01 312000 - Page 20 of 48

2. Excavation and Backfilling for Structures
2.01 Excavation to foundation of structures associated with networks such as culverts, utility
ducts, and for other major and minor structures are given in cubic meters. The quantities
given are bulk before excavating.
2.02 Rate is deemed to include:
any method of excavating (including hand excavation) and working,
excavating in any material encountered including rock ,
removal of unsuitable materials from the site and storage of suitable materials for use
as filling,
variations to bulk,
commencing excavating at any level and excavating to any depth,
any width of trench and any number of pits,
curved excavation,
excavating below ground water level (irrespective of any difference between the post-
contract and pre-contract level),
any temporary dewatering to enable excavation in the dry,
excavating to levels and grades shown on drawings,
design and installation and subsequent removal of temporary earthwork support

including support below ground water level, to unstable ground, next to roadways, next
to existing buildings and support left in,
designing providing and installing the temporary support system (secant pile wall,
soldier piles and lagging, sheet piling, tiebacks, rock anchors, bracing, rock bolts,
shotcrete, wire mesh, weep holes, etc.) or alternative support system,
excavating next to existing structures including walls and fences,
excavating next to existing services and around existing services crossing excavations
including temporary support, temporarily re-routing, sealing and removing services as
required,
breaking out existing materials and hard pavings including concrete, reinforced
concrete, brickwork, blockwork, stonework and drains,
extra excavation for working space and to accommodate earthwork support including
additional disposal, backfilling, work below ground water level, breaking out and
earthwork support,
00_TES_TM_004.01 312000 - Page 21 of 48

disposal of ground water and surface water,
keeping excavation free from water,
design, provide, install, test, operate, monitor, maintain, and dismantle and remove
when no longer required, a dewatering system of sufficient scope, size, and capacity to
control ground-water flow into excavations and permit construction to proceed on dry,
stable subgrades,
disposal of excavated material, on site or off site, including spreading and levelling or
depositing in spoil heaps, providing tip and paying fees and multiple handling,
inspecting the bottom of excavation upon reaching the foundation levels and
implementing subgrade treatment solution under foundations as and where deemed
necessary according to project specifications,
surface treatments including compacting surface of ground and bottoms of excavations,
levelling and grading to falls, trimming sloping surfaces and trimming vertical surfaces
to sides of cuttings (including trimming in rock and preparation of sub-grade) and
applying herbicides, pesticides, and anti-termite treatment,
excavation and removal of weak and unsuitable materials below the foundations level,
foundation subgrade inspection and preparation (as per the specifications),
planking and strutting and supporting the sides of excavation except for areas where
temporary support system is required,
any other necessary works for completing the work,
testing of materials as specified.
Structural excavation Cubic meter (m3)
4. Excavation and Backfilling for Utility Trenches
4.01 Trench excavation shall be paid for per meter cube measured in horizontal layers for
the different depth categories shown in the list of Pay Items. Trench length shall be
measured between outer surfaces of valves or valve chambers after subtracting 50 cm
from each side which shall be included in the chamber excavation. Trench width and
depth shall be as specified and as shown on Drawings. Trench depth shall be measured
from the finished ground level to the bottom of pipe bedding is included as trench
excavation.
4.02 Rates are deemed to include those of Clause 2.02.
Trench excavation
00_TES_TM_004.01 312000 - Page 22 of 48

to a depth of 2.0m Cubic meter (m3)
for depth from 2.01 to 3.0m Cubic meter (m3)
for depth greater than 12m Cubic meter (m3)
5. Filling and Backfilling
5.01 Filling for each of the following types is given in cubic meters:
Satisfactory fill material for backfilling structural excavations,
engineered fill to make up levels below foundations,
Bedding and Initial Backfill for pipes,
Satisfactory fill material for backfilling utility trenches,
Selected road subgrade Layer,5.02 Filling is measured as the net size in [m³] of the filling
placed in position, after compaction.
5.03 Filling of materials furnished, and screened, mixed with water, placed, spread,
compacted and finished, completed, and accepted. No measurement shall be made for
direct payment of over-depth construction, regardless of the Engineer's permission for
it to remain in place. Measurements shall be of areas computed from layout shown on
the drawings and of the field measurements of area and compacted depth of each trial
section.
00_TES_TM_004.01 312000 - Page 23 of 48

5.04 Work is deemed to include the costs of:
furnishing selected/suitable material according to specifications and from approved

sources,
using material arising from excavations including selecting and treating or using
imported filling material, the excavation and the transportation of the material from
approved borrow areas to site,
laying, spreading and raking to correct levels, falls and cambers,
filling, rolling and compaction as specified,
testing of materials as specified,
determining the optimum amount of water to be used with fill material to obtain
maximum dry density, for every borrow pit and for every type of filling material,
the required tests for approval of the borrow areas and the periodic test for the
verification that no change has occurred since the original approval,
preparing surfaces to receive filling layers and compacting as specified,
submitting representative samples for approval as per specification,
commencing filling at any level,
any width of fill, filling of any thickness,
spreading in layers, watering and compacting each layer including levelling and grading
to falls and slopes, and loss of material into ground during filling and compaction,
carrying out field density test as specified and at the rates specified,
proper formation of embankments, trimming of slopes, preparation and completion of

the road subgrade and shoulders,
embankment for benching,
structural filling to excavations adjacent to building, external concrete walls/ retaining

walls, and roadways with suitable material arising from excavations or imported filling
material including multiple handling as required, testing, spread in layers, and watering
and compacting each layer,
filling to soil replacement excavation with suitable material and compacting in layers
as required,
shaping sides and top of filling to profiles and levels shown or required including
preparation of sub-grade,
00_TES_TM_004.01 312000 - Page 24 of 48

drainage layer behind retaining walls including multiple handling as required and
compacting in layers,
sanitary fill above raft including multiple handling as required and compacting in layers,
multiple handling,
variations to bulk,
filling below ground water level,
removing from site unsuitable and surplus filling materials,
blinding surfaces of filling with sand, gravel, ash or other fine material.
Satisfactory fill material for backfilling structural excavations Cubic meter (m3)
Engineered fill to make up levels below foundations Cubic meter (m3)
Bedding and Initial Backfill for pipes Cubic meter (m3)
Satisfactory fill material for backfilling utility trenches Cubic meter (m3)
Selected road subgrade Layer Cubic meter (m3)
6. Drainage and Filter Materials
6.01 Drainage and filter materials are given in cubic meters.
furnishing selected/suitable material according to specifications clause 2.3 and from

approved sources,
submitting representative samples for approval as per specification,
filling to subsurface drainage as per specifications clause 3.24,
filling to drainage blanket as per specifications clause 3.25,
filling to drainage course under concrete slab-on-grade as per specifications clause 3.27,
preparing surfaces to receive filling layers and compacting as specified,
spreading in layers, watering and compacting each layer as specified,
carrying out field density test as specified and at the rates specified,
any other necessary works for completing the work.
00_TES_TM_004.01 312000 - Page 25 of 48

Drainage material Cubic meter (m3)
Filter material Cubic meter (m3)
00_TES_TM_004.01 312000 - Page 26 of 48

313223.17 PROBING AND GROUTING
1. Probing
1.01 Probe drilling is given in meters. Lengths of probes are measured from bottom
excavation level of foundation till end of probes.
1.02 Rates for measured work are deemed to include:
mobilizing and erecting drilling rig and equipment on drill hole locations,
dismantling and moving from location to location, and demobilizing upon completion,
drilling vertical or inclined holes,
providing temporary support for sides of drill holes,
drilling through any material, including rock and artificial obstructions,
backfilling drill holes with approved materials upon completion of the work,
and restoring ground surface to approved formation,
providing drilling records and reports.
2. Grouting
2.01 Filling of cavities and fissures beneath foundation levels is given in cubic meters and
as set out in the Bills of Quantities.
designing mixes, including all tests and quality control procedures,
preparatory works,
any method of delivery, pouring, placing, compacting, and curing,
any volume(s) or any number of cavities and/or fissures, including work in small or
isolated quantities,
the rates for filling of cavities located beneath foundations level shall include material,
workmanship, equipment and preparing and submitting method statement to the
Engineer’s approval.
Probe drilling Linear meter (l.m)
Filling with grout Cubic meter (m3)
00_TES_TM_004.01 313223.17 - Page 27 of 48

313223.18 GROUND IMPROVEMENT
1.01 Ground improvement is measured by square metre of the area improved.
1.02 The rate shall include, without limitation, the following:
selecting the most appropriate form(s) of ground improvement and full design for the
selected method,
provision of all equipment, mobilization, supplying and installing construction
materials and constructing a ground improvement system,
pre-improvement and post-improvement tests required for the assessment and
performance verification works and provisioning of testing certificates, test results etc.,
in addition to treatment of the top layer after improvement (if needed) are deemed,
execution of trial area(s) for confirming design parameters and define the most efficient
ground improvement method,
any temporary works necessary for the proper execution of the ground improvement
works to suit the approved ground improvement design and the Contractor’s
construction method including the mobilization/ demobilization and any other works in
connection with preparation of Contractor’s working platform,
excavation and filling for working platform, platform preparation, removal and disposal
of any unsuitable material,
ground improvement shall be designed, provided, installed, monitored in accordance
with the approved design and method statement and to the satisfaction of the Engineer,
submission of a detailed method statement to the approval of the Engineer,
obtaining the necessary approvals and permits from Authorities,
installation next to existing services and around existing services including temporary
support, temporarily re-routing, sealing and removing services as required,
supply, delivery, storage, multiple handling, placing, compaction, testing and any other
works associated with the construction of the adopted improvement technique,
supply, delivery, storage, stock piling, multiple handling, installation of all material
required for the execution of the ground improvement works,
any mock-ups, samples or additional testing that may be required by the Engineer,
all material, workmanship and equipment necessary for the execution of the ground
improvement works,
any other works auxiliary works contingent upon or incidental to the execution of the
ground improvement works.
Ground improvement Square meter (m2)
00_TES_TM_004.01 313223.18 - Page 28 of 48

313613 GABION BOXES
1.01 Gabion walls shall be measured by cubic metres furnished, installed, completed and
accepted. Dimensions shall be as shown on the Drawings.
provision of stone from approved source,
testing of stone material,
provision of galvanized steel wire mesh,
assembling of the galvanized steel wire mesh baskets to the specified sizes,
provision of wires and all necessary materials for assembling and joining the units, as
specified,
filling baskets with stones.
Gabion boxes Cubic meter (m3)
00_TES_TM_004.01 313613 - Page 29 of 48

313716.20 STONE RIPRAP
1.01 Stone riprap is given in cubic metres.
provision of stone from approved source,
testing of stone material,
compaction of ground surface to be protected by stone riprap,
placing of stone riprap,
surface finishing.
Stone riprap (indicate class) Cubic meter (m3)
00_TES_TM_004.01 313716.20 - Page 30 of 48

DIVISION 32:
EXTERIOR IMPROVEMENTS
DIVISION 32 EXTERIOR IMPROVEMENTS
32116.16 AGGREGATE SUB-BASE COURSE
1.01 Aggregate Sub-base Course shall be measured in cubic meters (m3) of aggregate
materials of the indicated layer thickness, furnished, crushed and screened, mixed with
water, placed, spread, compacted and finished, completed, and accepted. Measurements
shall be based on the cross sections shown on the For Construction Drawings and on
the field measurements of area and compacted depths/thicknesses. No measurement
shall be made for direct payment of over-depth construction, regardless of the
Engineer's permission for it to remain in place.
Aggregate Sub-base Course Cubic meter (m3)

(Indicate Thickness in mm)
Provision, placement and compaction of

Aggregate Sub-base Course (CBR ≥ 50%).
00_TES_TM_004.01 32116.16 - Page 31 of 48

321123 AGGREGATE BASE COURSE

1.01 Aggregate Base Course shall be measured by cubic meter (m3) of aggregate materials
of the indicated layer thickness, furnished, crushed and screened, mixed with water,
placed, spread, compacted and finished, completed, and accepted. Measurements shall
be based on the cross sections shown on the For Construction Drawings and on the field
measurements of area and compacted depths/thicknesses. No measurement shall be
made for direct payment of over-depth construction, regardless of the Engineer's
permission for it to remain in place.

Aggregate Base Course Cubic meter (m3)
Provision, placement and compaction of Aggregate
Base Course (CBR ≥ 80%).
00_TES_TM_004.01 321123 - Page 32 of 48

321216 ASPHALT PAVING
1.01 Bituminous Wearing Course and Bituminous Base Course shall be measured in cubic
meter (m3) of mix of the indicated thickness, furnished spread, compacted, completed
and accepted. Measurements shall be based on the areas and compacted thickness as
shown on the For Construction Drawings or otherwise directed by the Engineer.
1.02 Deficiencies in thickness of the wearing course shall, unless an overlay is constructed
at the Contractor’s expense, result in a proportion only of the surface course area being
measured for payment. This proportion shall be determined as stipulated in Clause
3.12.F (Points 8 & 9) of the Project Specifications Section 321216 “Asphalt Paving”.
1.03 Bituminous prime and tack coats shall be measured by the square meter (m2) of the
areas coated at the appropriate rate approved by the Engineer.
1.04 Surface preparation, protective measures to avoid staining or damage to appurtenances,

blotting of prime coats when required, and cleaning stains and repairing damage caused
by equipment, etc shall not be measured for direct payment, but shall be considered as
subsidiary works the costs of which will be deemed to be included in the contract prices
for the Pay Items.
1.05 Bituminous Layers constructed by order of the Engineer to correct deficiencies in total
thickness of bituminous courses or to compensate for major deficiencies in the
thickness of any underlying bituminous course, shall not be measured for direct
payment, but shall be considered as subsidiary works the costs of which will be deemed
to be included in the contract prices for Pay Items.
1.06 Establishment of the Job Mix Formula, surface preparation, construction of joints, hand
painting of contact surfaces, remedial treatment of surface irregularities, cutting of
cores and slabs for testing or measurement purposes, reinstatement of core and slab
areas of pavement, rolled down longitudinal bituminous edge strips, additional
thickness of bituminous course in excess of the specified thickness, and other ancillary
items shall not be measured for direct payment, but shall be considered as subsidiary
works the costs of which will be deemed to be included in the contract prices for Pay
Items.
00_TES_TM_004.01 321216 - Page 33 of 48

1.07 Roadworks Reinstatement of Surfaces
Surface reinstatement works should be executed according to the Specifications of the

Ministry of Transport, and Municipalities and the “Technical Specifications”. The
Contractor should refer to the latest edition of these Specifications.
This shall include saw cutting the existing pavement including the surface layers and
any stabilized and/or aggregate base and sub-base layers to their full depth, to reach the
grades shown on the “For Construction Drawings” and as per the instructions and the
satisfaction of the Engineer on Site, and the reinstatement of the same pavement layer
thicknesses, using approved material and construction procedures in compliance with
the Specifications mentioned above.
Sealing of cracks shall not be measured for direct payment but shall be considered as
subsidiary works the costs of which will be deemed to be included in the Contract Rates
and Amounts for related Pay Items.
Pavement repairs shall be, prepared, filled, compacted, completed and accepted. The
area shall be calculated based on payable trench width as shown in the table of the
trench excavation detail. Measurement shall be of the areas shown on the Drawings
and/or as directed by the Engineer.
Pay Item Unit Of Measurement
Bituminous Wearing Course Cubic meter (m3)

Provision, placement and compaction of
Bituminous Wearing Course, complete in all
respect as per Specifications, Method of
Measurement, and the For Construction
Drawings.
Bituminous Base Course Cubic meter (m3)

Provision, iplacement and compaction of
Bituminous Base Course, complete in all respect
as per Specifications, Method of Measurement,
and the For Construction Drawings.
Bituminous Prime Coat. Square meter (m2)
Bituminous Tack Coat. Square meter (m2)
Saw Cut and Reinstatement of Road Surfaces. Square meter (m2)
00_TES_TM_004.01 321216 - Page 34 of 48

321400 UNIT PAVING
1.01 Each kind of block and slab, coping and cladding, and walls is given separately.
Patterned work and work in multi-colors are each so described, stating the nature of the
work.
1.02 Work to each of the following is given separately:
pavings,
treads,
risers (including undercut risers),
upstands (including sides and tops of plinths, kerbs and upstand beams),
channels, pits and the like (including bottom and sides).
1.03 Skirtings, strings and the like are each given separately.
1.04 Work to seats, planters, pools and other special features are each given separately.
1.05 Thickness, dimensions, types and details are stated in descriptions, where necessary, to
identify the work. Thickness stated is the thickness exclusive of keys, grooves and the
like.
1.06 Sloping and curved work are each so described.
1.07 Work to pavings, treads, risers, upstands, channels, pits and the like is given in square
metres measured on the exposed face. No deduction is made for voids not exceeding
0.50 m2.
1.08 Skirtings, strings and the like are given in metres.
Pavings Square meter (m2)
Treads and Risers Linear meter (Lm)
Upstands Linear meter (Lm)
Channels Linear meter (Lm)
Pits Item
Skirtings and Strings Linear meter (Lm)
Site furnitures and special features Item
00_TES_TM_004.01 321400- Page 35 of 48

1.09 Work to seats, planters, pools and other special features is enumerated.
work of any width, height or girth,
extra work involved in patterned work and work in multi-colors,
work laid to falls and crossfalls, and intersections on sloping work,
raking and vertical work to skirtings, strings and the like
working over and around obstructions, pipes and the like and into recesses and shallow
channels,
bedding mortars and other fixing materials,
jointing, grouting and cleaning,
fair joints, edges, internal and external angles, ends and outlets,
special and non-standard blocks and slabs.
1.11 Paving accessories
Each kind of paving accessory is given separately, stating the kind of material,
Each type or size is given separately,
Curved work is so described,
Movement joints and the like are given in metres,
Tree grilles and the like are enumerated,
Rates for measured work are deemed to include the costs of:
all components of composite units,
ends, angles and intersections.
Paving accessories Item
Curved Work Linear meter (Lm)
Movement joints Linear meter (Lm)
Tree grilles Item
00_TES_TM_004.01 321400- Page 36 of 48

DIVISION 33:
UTILITIES
(Pipes, connections, valves, chambers and
manholes)
DIVISION 33 UTILITIES
330507.36 MICRO TUNNELING AND PIPEJACKING
1.01 Microtunneling and pipejacking works for highway and railway crossings shall be
measured by linear meters for different internal pipe diameters along the centerline of
the pipeline from the inside face of the launching shaft to the inside face of the reception
shaft as specified and shown on the Drawings.
1.02 Price shall include and be full compensation for labor, equipment, materials, and
supervision for construction works and for carrying out all related surveys,
investigations and monitoring works , construction of shafts for launching and reception
and thrust walls including excavation, excavation support, dewatering, casting concrete,
and for acquiring permits and coordination with authorities for all related matters and
any other work necessary or incidental to the completion of works.
Microtunneling and pipejacking works (state diameter) Linear meter (l.m)
00_TES_TM_004.01 330507.36 - Page 37 of 48

333111 PUBLIC SANITARY SEWERAGE GRAVITY PIPING & 333123

SANITARY SEWERAGE FORCE MAIN PIPING
1 Pipes, Fittings and Accessories
1.01 Pipes and Accessories
Each material of pipe is given separately.
Each diameter of pipe is given separately. Diameters stated are nominal diameters.
Depth of excavation is stated separately for pipes.
Trench excavation, bedding and backfilling shall be measured and paid for in
accordance with section ‘Excavation and Backfilling for Utility Trenches.
Pipes, fittings and accessories shall include the following as applicable for gravity and
pressure pipes:
Supply of pipes, couplings, end caps and all appropriate fittings, specials and
jointing materials.
Transportation and hauling about the site, loading, unloading and laying in the
trench or fixing to appropriate structure.
Cutting, machining, chamfering, etc... of standard-length pipes.
Lubricating agent used for assembling the pipe sections.
Piping sleeves, unless stated as pay item in the BOQ.
Assembling the pipes and couplings and connecting to fittings and valves or
chambers, manholes and or structures as applicable.
Bolts, nuts, gaskets and other material for flanged fittings.
Warning tape for metal pipes and dielectric tape for non-metal pipes
Concrete thrust blocks including steel works and associated over excavation and
anchors for force mains.
Testing as per specification.
All ancillary works and materials.
Flushing, cleaning, lining and coating.
Any other works needed
Concrete to insure work completion.
00_TES_TM_004.01 333111 & 333123 - Page 38 of 48

Concrete encasement shall be paid by cubic meter where the width and depth of
concrete encasement shall be 40cm plus the outside diameter of pipe as shown on
drawings. Length of pipe shall be measured on site and pipe volume based on outside
diameter shall be deducted from the total volume of concrete.
Rates for pipes are deemed to include all auxiliary fittings and accessories which are
not classified /specified in the BOQ.
Unless stated as pay items in the BOQ, items like equipment, forms, tools, furnishing
and placing of material and any other item required to complete appropriately will not
be measured for direct payment but shall be considered as subsidiary works, the cost of
which will be deemed to be included in the contract rates and amounts for the related
pay items.
Pipelines shall be paid for per linear meter covering, supply of materials, earthworks,
bedding, installation, bends, tees, all fittings, testing and commissioning and all items
listed above, unless stated as pay items in the BOQ. The pipe length shall be measured
as a straight line between the external faces of consecutive manholes or the centres of
consecutive coupling sections or valves for force mains. No allowance will be made
for cut ends and waste.
Pipe Linear meter (L.m)
Concrete encasement for pipes Cubic meter (m3)
1.02 Service Connections
Sewer connections to houses shall be measured as three different components.
1- Connection to main sewer

Works related to house connections to sewer network by mean of ‘Y’ or ‘Tee’
connections or manholes shall include:
Supply of all materials, pipes sections, couplings, protection works, encasement,

manholes opening, and special pipes, etc… “Y” and “Tee’ connections for direct
connection, drilling and fitting of pipe for manhole connection, end cap and marker
post.
Mounting connecting, testing, and commissioning
Sewer connections to houses shall be paid for paid per unit (Nr.).
2- Inspection chambers (refer to section 3)

3- Pipe connections (Additional pipes for connections longer than 5m)
00_TES_TM_004.01 333111 & 333123 - Page 39 of 48

Rates for connections are to include all the items listed above for pipes (1.01) and
earthworks (section ‘Excavation and Backfilling for Utility Trenches)
Pipe connections to buildings shall be paid for per linear meter of pipe.
4- Cleanouts: payments shall include all materials and connections as well as

mounting, connecting, testing and commissioning.
Cleanouts shall be paid for per unit (Nr.).
Sewer service connection Number (Nr)
Connection pipes (stating type and diameter) Linear meter (L.m)
Cleanouts Number (Nr)
2 Valves and Accessories on Force Mains
2.01 Valves and Accessories
Each type of valve shall be given separately.
Each type of valve shall be classified by its diameter.
Valves, and the like shall be enumerated.
The rates for valves and accessories are deemed to include the following:
Supply of valves, fittings, couplings and specials for connection to adjacent network
as specified.
Lowering into trench and installation.
Additional excavation, backfilling, bedding.
Concrete supports and thrust blocks including all items required for Concrete
Works, and steel reinforcement.
Flexible couplings for directly buried valves.
Dismantling joints and flanged and socket adapters for connecting to adjacent
spigot end pipe or fitting.
Valve box complete with cover, lock and key, concrete surround and extension
spindles including square nuts to fit spindles for directly buried valves.
Operating key or hand wheel for valves in chambers.
Valve marker post and plate.
00_TES_TM_004.01 333111 & 333123 - Page 40 of 48

Bolts, nuts, gaskets, extension spindles and ancillary works including materials
required.
Painting, lining and coating.
Any other works needed to insure work completion.
Valves, shall be paid per unit (Nr.) installed according to size indicated in the Bill of
Quantities.
Actuators shall be paid per unit (Nr.) installed according to size and type indicated with
Bill of Quantities.
2.02 Air Valves for force mains
Each type of air valve is classified by its diameter.
Air valves are enumerated.
The rates for air valves are deemed to include the following:
Supply of valve, fittings and specials as specified and shown on the drawings.
Associated isolating gate valves.
Drilling and fixing the pipe threaded outlet for threaded connection.
Additional excavation, backfilling, bedding.
Concrete supports and thrust blocks including all items required for Concrete
Works, and steel reinforcement.
Valve marker post and plate.
Items, like dismantling couplings, puddle flanges tee and/or saddle for connecting
to main line.
Ancillary works and materials required and all labour and equipment used.
Painting, lining, coating.
Installing and testing.
Air Valves shall be paid per unit (Nr) installed according to size indicated in the Bill of
Quantities.
Unless shown as pay items in the BOQ, items of work equipment, forms, tools,
furnishing and placing material, breaking into existing pipes, blinding works, labour or
any other item necessary for the proper completion of the work shall not be measured
00_TES_TM_004.01 333111 & 333123 - Page 41 of 48

for direct payment but shall be considered as subsidiary works, the cost of which will
be deemed to be included in the contract rates and amounts for due related pay items.

Isolation Valves on force mains
(gate or butterfly) Number (Nr)
Air Valves on force mains Number (Nr)
3 Manholes, Inspection and Valve Chambers
Manholes and chambers shall be enumerated per diameter size and depth. Each material
given separately.
Rate for manholes, chambers and inspection chambers shall include for the following:
Excavation in any natural material in accordance with the section ‘Earth’. Moving
including soil support, dewatering, backfilling and cauting away.
Concrete (cast-in-situ and precast), blinding, reinforcing steel, beds, surrounds,

benching and flexible couplings including all items required for Concrete Works
and Concrete Structures and all temporary works.
Protective coating of exposed faces of concrete.
Concrete rings as required to make up levels.
Concrete or brick blockwork corbelling as required.
Granolithic rendering to benching.
Fittings, inside manhole wall with each pipe section, short pieces within manholes
and within the external faces of the walls or the protrusions, and the concrete
surround of manhole back drop.
Covers, grates and frames with all ancillary work.
Testing structures for water tightness and any subsequent re-testing.
Ladders, rungs and puddle flanges built into walls.
All other ancillary items.
Manhole, chambers and inspection chambers shall be paid for per unit installed and
according to the depth and diameters sizes categories shown in the bill of quantities.
00_TES_TM_004.01 333111 & 333123 - Page 42 of 48

Manhole Number (Nr)
Inspection chamber Number (Nr)
Isolation valve chamber Number (Nr)
Air release valve chamber Number (Nr)
Other valve chamber Number (Nr)
No separate payment shall be made for surface reinstatement, breaking into existing
pipes, equipment, forms, tools, furnishing and placing material, labour or any other item
necessary for the proper completion of the work. All such additional items shall not be
measured for direct payment but shall be considered as subsidiary works, the cost of
which shall be deemed to be included in the contract rates and amounts for related pay
items.
4 Protective Coatings
Protective coatings are deemed to be included in measured items for pipe, fitting, valve,
etc to which they are applied.
Protective coatings are not measured separately but shall include:
Preparation of surface.
Supplying all necessary tools and equipment, adhesives, bonding agents, etc.
Work in any location, any area or width.
Rubbing down between coats.
Cutting in edges.
Making good to damaged areas.
Protection.
Testing when required by the Project Engineer.
No separate payment will be made for protective coating. The cost shall be included
with the rate of the respective item requiring such work.
00_TES_TM_004.01 333111 & 333123 - Page 43 of 48

5 Connecting Works to Existing Networks
Work is measured and shall be paid as an Item.
The rates of such work are deemed to include the following:
Temporary diversion or stopping of flow in existing networks.
All earthworks including excavation, bedding and backfilling.
Preparing existing work to receive or discharge to new work including any hand
excavation to expose pipe and subsequent backfilling.
All cutting machining required to facilitate the connection.
All pipe works as listed above, fittings, fixing and jointing materials.
Making good all work disturbed and reinstating surfaces as per directions of the
Engineer.
Disposal of materials arising.
Testing and inspection.
All co-ordination required with utility authorities, all ancillary items and all costs
associated with authorities’ requirements and procedures for maintaining
uninterrupted service.
Connection to existing network Item
6 Relocation of Existing Utilities
Payment for relocation of services shall be made in linear made at rates given in the
BOQ. The works shall cover also all incidental expenses and any sum paid by contractor
to any competent public or private authority.
Removal and/or relocation of electrical and telecom cables shall be made according to
the requirement of the respective Authority for both the material specification and the
workmanship required. Payment shall be made according to rates given in the BOQ.
Relocation or Removal of Existing Utilities Linear Meter (l.m)/ square

meter (m2)
00_TES_TM_004.01 333111 & 333123 - Page 44 of 48

DIVISION 40:
PROCESS INTERCONNECTIONS
DIVISION 40 – PROCESS INTERCONNECTIONS
406000 - PROCESS CONTROL AND ENTERPRISE SYSTEM
1 Process SCADA System
Supply, installation and termination of all SCADA system equipment as specified and
shown on design drawings including, but not limited to, the following:
Application and Data Servers
Historian Servers
Operator Workstations
Maintenance Laptops
19” Racks
Wall Mounted LCD’s
Computer Peripherals
SCADA Software
Ethernet Switches
Gateway RTUs
Field Interface Units
Control Room Furniture
Supply of all necessary installation accessories
Conducting Factory Acceptance Tests
Conducting Site Acceptance Tests
Testing and Commissioning of above-mentioned controls
Training of Employer’s maintenance staff
Handing over to Employer
00_TES_TM_004.01 406000 - Page 45 of 48

2 Process Controllers
Supply, installation and termination of all control systems as specified and shown on
design drawings including, but not limited to, the following:
DC Power Supplies
Ethernet Switches
PLC’s
HMI’s
PLC / RTU Software
Remote I/O’s
Remote Terminal Units (RTU’s)
PLC Cabinets
Components of PLC Cabinets
RTU Cabinets
Components of Remote Terminal Units Cabinets
Wireless Radio frequency Communications Devices
4G/GPRS Communication Devices
Interfaces / Integrations with Packaged Equipment and Low Current Systems
Testing and Commissioning of above-mentioned controls
00_TES_TM_004.01 406000 - Page 46 of 48

3 Process Control / Telemetry Wiring
Supply, installation and termination of all cables, wires and cable containment as
specified and shown on design drawings including, but not limited to, the following:
Junction Boxes
Fiber Optic Cables
Fiber Optic Splicing and Splicing Boxes
Fiber Optic Patch Panels
Patch Cords
Instrumentation and Control Cables
Communication and Data Cables and Cables Connectors
Cable Ducts
Cable Trays
Conduits
Manholes
Testing and Commissioning of above-mentioned cabling and wiring
4 Process Field Instrumentation
Supply, installation and termination of all instrumentation as specified and shown on

design drawings including, but not limited to, the following:
00_TES_TM_004.01 406000 - Page 47 of 48

Pressure Transmitters
Differential Pressure Transmitters
Pressure Gauges
Differential Pressure Gauges
Pressure Switches
Differential Pressure Switches
Level Transmitters
Level Switches
Conductivity Analyzers
PH Analyzers
Redox (ORP) Analyzers
Turbidity Analyzers
Ammonium Analyzers
Residual Chlorine Analyzers
Instrument Enclosures
Instrument Piping
Instrument Valves
Instrumentation Power Panels
Supply of all necessary instrumentation valves and tubing as shown on drawings
Testing and Commissioning of above-mentioned instrumentation
00_TES_TM_004.01 406000 - Page 48 of 48

Method of Measurements For Sewer Networks-3

Uploaded by

Copyright:

Available Formats

Method of Measurements For Sewer Networks-3

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Method of Measurements For Sewer Networks-3

Uploaded by

Copyright:

Available Formats

The Specification, Bills of Quantities and Typical Details

The Specification, Bills of Quantities and

Document Number: 00_TES_TM_004.01

This Issue Date 24/01/2021 11/06/1442 (H)

Copyright Notice ©Copyright 2020

Issue Date 24/1/2021

SCOPE AND BASIS OF PAYMENT

A Quantities determined in accordance with this Standard Method of Measurement for

B Wherever any "Measurement" rule, as contained in this Standard Method of

00_TES_TM_004.01 Preamble - Page 1 of 48

L.m. = Linear meter m3 = meter cube

m2 = meter square L.s. = Lump sum

All rates and amounts shall be quoted in Saudi Riyals (S.R).

00_TES_TM_004.01 Preamble - Page 2 of 48

DIVISION 1 GENERAL REQUIREMENTS

011100 SCOPE AND CONTROL OF WORKS

013500 SAFETY PRECAUTION MEASURES

014300 CONTROL OF MATERIALS AND STANDARDS FOR SAMPLING AND

00_TES_TM_004.01 010000 - Page 3 of 48

DIVISION 26 ELECTRICAL WORK

260513 MEDIUM VOLTAGE CABLES & 260519 LOW VOLTAGE

Pay Item Unit of Measurement

Medium voltage cables Linear meter (Lm)

00_TES_TM_004.01 260513 & 260519 - Page 4 of 48

260526 GROUNDING AND BONDING FOR ELECTRICAL SYSTEMS

1.02 Earthing conductors are given in linear meters.

1.03 Earth pits are given in number.

1.04 Earth rods are given in number.

1.05 Clamps are given in number.

1.06 Earthing test links are given in number.

bonding to all metallic equipments as per specification,

Pay Item Unit of Measurement

Earthing Conductors Linear meter (Lm)

Earth Pits Number (Nr)

Earth Rods Number (Nr)

Clamps Number (Nr)

Earthing Test Links Number (Nr)

00_TES_TM_004.01 260526 - Page 5 of 48

261200 MEDIUM VOLTAGE TRANSFORMERS

1.02 Transformers are enumerated.

all auxiliaries, instruments, sensors, controls and necessary protection,

neutral earthing resistances where applicable,

surge arresters unless included under MV switchgear,

supports required for installation of transformers on bases and/or trenches,

spare parts, tools and instruments.

Pay Item Unit of Measurement

MV/LV Transformer Number (Nr)

00_TES_TM_004.01 261200 - Page 6 of 48

261300 MEDIUM VOLTAGE SWITCHGEAR

all auxiliaries, instruments, sensors, controls and necessary protection,

supports required for installation of switchgear on bases and/or trenches,

spare parts tools and instruments.

Pay Item Unit of Measurement

RMU/MVSG Number (Nr)

00_TES_TM_004.01 261300 - Page 7 of 48

262413 SWITCHBOARDS & 262416 PANELBOARDS

1.02 Switchboards and panelboards are enumerated.

termination of incoming and outgoing cables to equipment including cable glands,

all components housed within the switchboard or panelboard,AC or DC power supply