Scribd
Upload
59 views2 pages

5.2.1 Packet Tracer - Configure Basic EIGRP With IPv6 Routing

The document describes configuring EIGRP routing for IPv6 between three routers - R1, R2, and R3. It involves enabling IPv6 routing and the EIGRP process on each router, assigning unique router IDs, configuring EIGRP on the interfaces, and setting passive interfaces. The configuration is then verified by checking for EIGRP neighbor adjacencies, examining the EIGRP routing table, and confirming end-to-end connectivity between PCs.

Uploaded by

venkteshmmoger13
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
59 views2 pages

5.2.1 Packet Tracer - Configure Basic EIGRP With IPv6 Routing

The document describes configuring EIGRP routing for IPv6 between three routers - R1, R2, and R3. It involves enabling IPv6 routing and the EIGRP process on each router, assigning unique router IDs, configuring EIGRP on the interfaces, and setting passive interfaces. The configuration is then verified by checking for EIGRP neighbor adjacencies, examining the EIGRP routing table, and confirming end-to-end connectivity between PCs.

Uploaded by

venkteshmmoger13
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Packet Tracer - Configure Basic EIGRP with IPv6

Addressing Table
Device Interface IPv6 Address Default Gateway

R1 G0/0 2001:db8:cafe:1::1/64 N/A


R1
S0/0/0 2001:db8:cafe:a001::1/64 N/A

R1
S0/0/1 2001:db8:cafe:a003::1/64 N/A

R1
Link-local fe80::1 N/A

R2 G0/0 2001:db8:cafe:2::1/64 N/A


R2
S0/0/0 2001:db8:cafe:a001::2/64 N/A

R2
S0/0/1 2001:db8:cafe:a002::1/64 N/A

R2
Link-local fe80::2 N/A

R3 G0/0 2001:db8:cafe:3::1/64 N/A

R3
S0/0/0 2001:db8:cafe:a003::2/64 N/A

R3
S0/0/1 2001:db8:cafe:a002::2/64 N/A

R3
Link-local fe80::3 N/A

PC1 NIC 2001:db8:cafe:1::3/64 fe80::1


PC2 NIC 2001:db8:cafe:2::3/64 fe80::2
PC3 NIC 2001:db8:cafe:3::3/64 fe80::3

Objectives
Part 1: Configure EIGRP for IPv6 Routing
Part 2: Verify IPv6 EIGRP for IPv6 Routing

Scenario
In this activity, you will configure the network with EIGRP routing for IPv6. You will also assign router IDs,
configure passive interfaces, verify that the network is fully converged, and display routing information using
show commands.
EIGRP for IPv6 has the same overall operation and features as EIGRP for IPv4. There are a few major
differences between them:
 EIGRP for IPv6 is configured directly on the router interfaces.
 With EIGRP for IPv6, a router-id is required on each router or the routing process will not start.
 The EIGRP for IPv6 routing process uses a “shutdown” feature.

 2014 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1 of 2 www.netacad.com
Packet Tracer - Configure Basic EIGRP with IPv6

Instructions

Part 1: Configure EIGRP for IPv6 Routing


Step 1: Enable IPv6 routing on each router.

Step 2: Enable EIGRP for IPv6 routing on each router.


The IPv6 routing process is shut down by default. Issue a command that will enable EIGRP for IPv6 routing in
R1, R2 and R3.
Enable the EIGRP process on all routers and use 1 as the Autonomous System number.

Step 3: Assign a router ID to each router.


The router IDs are as follows:
 R1: 1.1.1.1
 R2: 2.2.2.2
 R3: 3.3.3.3

Step 4: Using AS 1, configure EIGRP for IPv6 on each interface.

Step 5: Configure IPv6 passive interfaces


On each router, configure the LAN interface to not send EIGRPv6 updates.
Note: Packet Tracer currently does not score the EIGRPv6 passive-interface command.

Part 2: Verify EIGRP for IPv6 Routing


Step 1: Examine neighbor adjacencies.
Use the command show ipv6 eigrp neighbors to verify that the adjacency has been established with its
neighboring routers. The link-local addresses of the neighboring routers are displayed in the adjacency table.

Step 2: Examine the IPv6 EIGRP routing table.


Use the show ipv6 route command to display the IPv6 routing table on all routers. EIGRP for IPv6 routes are
denoted in the routing table with a D.

Step 3: Verify the parameters and current state of the active IPv6 routing protocol processes.
Use the command show ipv6 protocols to verify the configured parameter.

Step 4: Verify end-to-end connectivity.


PC1, PC2, and PC3 should now be able to ping each other. If not, troubleshoot your EIGRP configurations.
End of document

 2014 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 2 of 2 www.netacad.com

You might also like