B2 Chapter7MRF
B2 Chapter7MRF
B2 Chapter7MRF
net/publication/349313158
CITATIONS READS
5 1,079
3 authors:
Kinjal J Shah
Nanjing Tech University
75 PUBLICATIONS 2,135 CITATIONS
SEE PROFILE
All content following this page was uploaded by Kinjal J Shah on 15 February 2021.
Chapter 7
New Class of Flocculants and Coagulants
Abstract
Coagulation is a kind of efficient water treatment method commonly used in domestic
anhydrous and industrial wastewater treatment. Inorganic polymer coagulants (polyvalent
metal salts) are widely used because of their low cost and ease of use. However, due to
the low flocculation effectiveness and the presence of residual metal concentrations in the
treated water, their application is limited. Organic synthetic flocculant has been widely
used due to its higher flocculation efficiency at lower dosage. However, it has limitations
in applicability due to its molecular structure which is less biodegradable and less
disperse in water. Therefore, flocculants based on natural polymers have attracted
extensive attention from researchers due to their advantages such as biodegradability and
environmental friendliness. This paper summarizes the overview of the development of
various types of flocculants that were used for industrial wastewater treatment. In
addition, the characteristics and application of flocculant is reviewed with their behavior.
Keywords
Coagulant, Flocculant, Coagulation, Flocculation, Organic/Inorganic Coagulants, Water
Treatment
Contents
219
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
1. Introduction
Wastewater from chemical processing industries contains various concentrations of
suspended solids, metal ions and other pollutants being smaller in size [1]. Due to the
small size of those particles, sedimentation and filtration has become challenge in recent
years [2]. Therefore, removing those colloidal particles from the wastewater is a serious
challenge for the industry. There are various traditional and advanced technologies been
used to remove colloidal particles from wastewater, such as ion exchange, membrane
filtration, precipitation, flotation, adsorption, coagulation, flocculation, and electrolysis
[3]. Among these methods, coagulation/flocculation is one of the most widely used
techniques to remove small particles from wastewater. Moreover, coagulation is a simple
and effective wastewater treatment method, and has been widely used to treat various
types of wastewater, such as domestic sewage, fine chemical wastewater, papermaking
wastewater, oily wastewater, pharmaceutical wastewater, etc. [4, 5]. In the coagulation
process, finely dispersed particles, aggregate or coagulate together to form large particles
(flocculate) after adding the coagulant and/or flocculant of larger size, which settle and
cause clarification of the system [6].
220
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
Inorganic polymer coagulant, mainly composed of inorganic metal salts such as iron salts
and aluminum salts (such as iron sulfate, ferric chloride, aluminum chloride, etc.) have a
long history of use [7]. However, such flocculants are more corrosive and costly.
Moreover, under certain conditions, the water purification effect is still not ideal.
Compared with traditional agents, inorganic polymer flocculants have better flocculation
effect, lower cost, less dosage, and wider pH requirements for wastewater [8]. However,
for complex sewage systems, it is difficult to obtain a satisfactory treatment effect using a
single flocculant. On the other hand, organic/inorganic composite flocculants can
overcome the shortcomings of using a single flocculant to make effective flocculation at
lower cost. Composite flocculant has greater advantages than single polymer flocculant,
lower cost, better flocculation effect and wider application fields; but still has the
disadvantages of producing more sludge and the need of large dosage. In case of the
organic flocculants, they are expensive, difficult to degrade, and their residual monomers
are toxic in nature. Moreover, its large dosage requirement, and poor stability, attracts the
research community to find alternative organic flocculants.
Meanwhile, natural flocculants have received more and more attention due to their low
cost, renewable, easily biodegradable and non-toxic nature [10]. So far, various polymer
flocculants have been developed or designed to improve the flocculation process of
wastewater treatment. Natural flocculants with macromolecule size are widely used in
wastewater treatment due to its pH resistance, small dosage, high efficiency, and ease of
treatment [11]. However, natural flocculants have moderate efficiency and short shelf
life. While, the main problems of synthetic polymer flocculants are non-biodegradability
and residual monomer toxicity. Thus, a lot of synthesis and research have been carried
out on grafting copolymers to enhance optimal properties [12]. However, finding
efficient and economical flocculants has always been a challenge faced by many studies.
The main influencing factors of flocculation efficiency include flocculation rate,
sedimentation rate, solid sedimentation percentage, turbidity removal rate, and pollutant
removal percentage or water recovery rate [13]. These influencing factors actually reflect
the size distribution and structure characteristics of flocs during flocculation. Larger,
stronger and denser flocs result in improved settling, filtration and clarification
performance in wastewater treatment [14].
This article reviews the flocculants studied and applied in wastewater treatment,
including inorganic salt coagulants/flocculants, polyacrylamide coagulants, organic-
inorganic composite coagulants, and natural modified coagulants. Inorganic salt-type
natural modified coagulants are natural raw materials widely developed and utilized in
recent years. At the same time, the graft flocculant has been studied recently, and
221
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
combined with the performance of chemical flocculant and natural flocculant. This article
reviews the literature on flocculants and its application in recent years.
222
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
has a strong adsorption and bridging effect on particles in water. During the falling
process of this polymer, the particulate matter in the water is net-trapped and swept,
thereby forming coarse flocs to sink to achieve the purpose of water purification. In
addition, in the formed series of multinuclear ions, the ions in the critical state before
flocculent precipitation have the best flocculation performance [19]. This may be related
to the ability of this critical product to neutralize the colloidal charge, compress the
electric double layer, and reduce the colloid potential, which promotes the rapid
aggregation and precipitation of colloidal particles and suspended solids [20].
223
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
sodium chlorate. In the printing and dyeing wastewater treatment experiment, when the
dosage of liquid PFS was 146 mg•L-1, the COD removal rate was 65.2%, and the
turbidity removal rate was 91.4%. It can be seen that the preparation of PFS by different
preparation methods has a greater impact on the coagulation performance of PFS.
224
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
long stability time and other advantages. The improvement of the properties of coagulant
can improve the efficiency of wastewater treatment, save the amount of reagents and
reduce secondary pollution, which is conducive to sludge removal and drying treatment.
Zhang et al. [29] prepared silica sol by stirring polymerized water glass and acidulant for
several hours, and then added ferrous sulfate and sodium chlorate to the silica sol to
prepare polymerized ferric silicate by copolymerization. The effects of 4 different
acidifiers and different n(Si):(Fe) on its reaction mechanism, stability, surface
morphology and coagulation performance were investigated [30]. As a result, it was
found that using acetic acid as the acidifying agent can delay the polymerization of silicic
acid, and the prepared polymeric silicic acid and polymeric ferric silicate have the best
stability. Polysilicate ferric sulfate is a new type of inorganic polymer coagulant
synthesized by compounding or copolymerizing iron ions and activated silicic acid using
the principle of synergy. Because this coagulant has both electrical neutralization and
adsorption bridging effects, with an average relative molecular mass of up to 200,000, it
is possible to partially replace organic synthetic polymer coagulants in water treatment to
avoid toxicity. Generally, iron ions and aluminum ions are used as coupling metal ions.
Compared with polyaluminum silicate, polyiron silicate is a better performance
coagulant, because it is basically harmless to the environment, fundamentally Eliminate
the problem of residual aluminum in water [31].
225
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
results show that the optimal condition for Na2S removal of Pb2+ is n(Na2S):n(Pb2+)=3.0,
and the reaction of Na2S precipitation Pb2+ satisfies the first-order reaction kinetic model.
The best preparation conditions of coagulant: temperature is 25 ℃, n(Fe):n(Si)=25,
n(NaOH):n(Fe)=0.5.
226
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
dyeing wastewater, domestic sewage, coking wastewater and so on. There are many
studies on the influencing factors that affect the flocculation effect, mainly including the
Al/Fe/Si molar ratio, the dosage of the coagulant and the pH value of the flocculation
treatment. In the polyaluminum ferric silicate coagulant, the Al/Fe/Si molar ratio mainly
affects the electric neutralization and adsorption bridging effect [38]. When the ratio is
too low, the negatively charged polysilicic acid neutralizes the positive charge of
aluminum iron ions, reduces the zeta potential of the electric double layer, reduces the
electrical neutralization ability, and affects the flocculation effect. When the ratio is too
high, the adsorption bridging effect of polyaluminum ferric silicate coagulant is affected.
The charge of the polyaluminum ferric silicate coagulant can neutralize the charge of
suspended particles, making the colloid unstable and remove it [39]. When the amount of
polyaluminum ferric silicate is too much, the adsorption of suspended particles to the
polyaluminum ferric silicate is too large, which may cause the colloid to re-stabilize, or
the polyaluminum ferric silicate wraps the suspended particles, and the "colloid
protection" effect occurs. Make the flocculation ability worse. When the dosage of
coagulant is too small, the adsorption bridging capacity is too weak, it is difficult to
connect the rubber bridging bridge, and the flocculation capacity is poor. Therefore, the
most suitable dosage of coagulant should not only ensure the rapid flocculation of the
colloidal particles, but also make the largest flocculated colloidal particles not easily fall
off [40]. In the process of preparing polyaluminum ferric silicate coagulant, pre-
hydrolysis experiment was carried out to greatly reduce the hydrolysis reaction in the
sewage treatment process. The coagulant can be applied to water bodies with a wider pH
range. Adjusting the pH value can change the nature and size of the charged surface of
the colloid in water, and affect the hydrolyzability of the coagulant. Generally speaking,
the pH value of the water body is within a certain range, and the coagulant has a better
treatment effect [41]. Each coagulant has its own suitable pH value range for different
water samples. If the pH value is too large, the polynuclear hydroxyl complex ion
generated by the hydrolysis of the polyaluminum ferric silicate coagulant decreases the
electrical neutralization ability, so the flocculation effect is poor, pH If the value is too
low, the protonation effect is obvious, which may cause the zeta potential to change from
negative to positive, causing the particles to re-stabilize, thereby affecting the
flocculation effect [42].
227
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
removal rate of turbidity, color, and phosphate [43]. It has the advantages of wide
adaptability to water temperature and pH, but it has strong corrosivity and is easy to color
water. Tang et al. studied the FeC13-Na2HPO4-NaHCO3 system, and as a result, the
surface PO43- participated in the hydrolysis and polymerization of Fe3+ [44]. Amorphous
Fe(OH)3 can adsorb H2PO4- and reduce the volume of the solution. These studies indicate
that PO43- can interact with Fe3+ and form a bridge. It can be expected that the
introduction of PO43- in PFS can increase the degree of polymerization due to the
formation of bridge bonds, which is beneficial to improve the flocculation performance
of PFS. Based on the polymerization of phosphate on Fe3+, related scholars have also
begun to study the preparation and application of polyphosphoric ferric sulfate [45].
There is a method for preparing solid PPFS by reacting solid PFS and Na3PO4•12H2O,
which are ground and mixed uniformly, at 120-180°C. Or use hydrogen peroxide to
oxidize ferrous sulfate to obtain PFS, then add Na3PO4, and dry to obtain solid PPFS.
Studies have shown that PPFS is significantly better than PFS in treating printing and
dyeing wastewater, titanium dioxide wastewater, and electroplating wastewater.
3. Polyaluminum coagulant
Polyaluminum chloride [PAC, Alm(OH)n(H2O)x] is an inorganic polymer coagulant
developed in the late 1960s. It is currently the most widely used and sold inorganic
coagulant and water treatment agent. The inorganic polymer coagulant represented by
PAC is much lower in price than the organic polymer coagulant, and it is easy to store,
and the preparation conditions are not as harsh as the organic polymer [47]. Compared
with traditional inorganic low-molecular aluminum salts, PAC has more high electric
charge, so it has stronger electrical neutralization ability and strong adsorption ability
and, shows excellent coagulation effect after being added to water. PAC has the
advantages of little influence on the pH of the effluent, less dosage, less sludge, and high
turbidity removal [48]. Currently, about 60% of water treatment plants in China use PAC
for coagulation treatment. The production process of PAC can be divided into aluminum-
containing mineral method, aluminum hydroxide method, aluminum chloride method,
and metal aluminum method according to the different raw materials. In addition, there is
a method for preparing PAC by using waste molecular sieve, polysilicon residue and red
mud as raw materials [49, 50].
As the quality of sewage water becomes more and more complex, a single coagulant can
no longer meet the needs of water treatment, the development of cationic composite
coagulant has been developed, and a lot of performance, copolymerization mechanism
and morphology of cationic composite coagulant have been developed. The
representative is iron-aluminum composite, that is, introducing Fe3+ into PAC to prepare
228
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
4. Literature references
Polyacrylamide (Polyacrylamide, PAM for short) is a general term for homopolymers
and copolymers of Acrylamide (AM for short) and its derivatives. It is a linear water-
soluble polymer [56]. It is derived from its molecular structure. Characteristics, PAM has
special physical properties and chemical properties, which are not only good in
flocculation, surface activity and thickening, but it is also easy to obtain a variety of
branched or network structures through grafting or crosslinking [57]. Modified products
are widely used in petroleum mining, sewage treatment, papermaking, mining and other
229
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
230
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
bridging, and net-sweeping. The specific mechanism of flocculation depends on the type
of coagulant, the size, concentration and nature of the impurity particles in the water, as
well as several environmental factors such as pH and ions. It often requires specific
analysis. The basis of adsorption-electricity neutralization is still that suspended particles
attract differently charged polymers, neutralize the charge carried by the colloidal
particles themselves, weaken the electrostatic repulsion between the particles, and thus
cause the suspended particles to coagulate spontaneously [62]. Adsorption is also
accomplished by electrical or van der Waals forces. Suspended matter in water is
generally not prone to aggregation due to the same charge of the particles or has a lower
density, so it exists stably in a highly dispersed state. The polymer chain of the
polyacrylamide coagulant can attract each other with the suspended particles. If the chain
contains groups that are different from the particles in electrical properties or are purely
attracted to each other by Edward force, then these particles can interact with coagulant
molecules combine to form a structure where a large molecule connects several
suspended particles. When polyacrylamide coagulant is put into water, if its molecular
chain can be fully stretched, a large number of coagulant molecules can form a fishnet-
like structure with each other, and they will come into contact with suspended solids
during their natural sinking process, and through mechanical action The particles are
rolled into the network structure, or entrapped between the gaps in the molecular chain,
so that the particles settle together with the coagulant [63].
Polyacrylamide (PAM) is one of the most important synthetic organic polymer
coagulants and one of the components of inorganic-organic composite polymer
coagulants. Xu et al. [64] dispersed diatomaceous earth into a solution containing
ammonium chloride and acrylamide. The prepared polycationic acrylamide/diatomite
composite coagulant can make the treated wastewater the light transmittance exceeds
95%, and the dosage of coagulant is only 7.5mg/L, which is much lower than that of
conventional coagulant 60~90mg/L. At the same time, the settling time is less than 5s,
similar to conventional coagulants. Li et al. [65] used modified coal gangue and
polyacrylamide (PAM) to prepare a new type of coagulant with both turbidity and color
removal properties. The flocculation test of oilfield drilling wastewater showed that the
turbidity removal rate of the new coagulant is 85.5%, the light transmittance of
wastewater after flocculation and sedimentation is 53.6%, and the turbidity removal
efficiency is much higher than PAM or PAM/gangue mixture. Xiong et al. [66] used
aluminum sulfate, iron sulfate, sodium silicate and cationic polyacrylamide (CPAM) as
the main raw materials, and prepared the PSAF-CPAM inorganic-organic composite
polymer blend by copolymerization. The results show that the best preparation ratio of
PSAF-CPAM is the mass ratio of inorganic coagulant to organic coagulant is 70:1. The
231
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
removal rate of PSAF-CPAM to the total phosphorus in printing and dyeing wastewater
increases with the increase of the dosage of coagulant Gradually increasing, the growth
trend slows down after the metal ion concentration of the coagulant dosage reaches 1
mol/L, and the total phosphorus removal rate is above 98%. Electron microscope
scanning (SEM) and Fourier infrared analysis (FTIR) were used to characterize and
analyze the morphology and structure of PSAF-CPAM coagulant, and it was found that a
new polymer formed due to a chemical reaction between PSAF and CPAM. Sun et al.
[67] placed acrylamide monomer, ferric chloride hexahydrate and aluminum chloride
hexahydrate in (NH4)2S2O8-NaHSO3 solution to synthesize a new type of composite
coagulant-poly Acrylamide (PAM)-polyaluminum ferric chloride (PAFC). A composite
flocculant synthesized with an initiator mass fraction of 0.5%, a polymerization
temperature of 50°C, a monomer mass fraction of 20%, and a polymerization time of 4h
was subjected to a flocculation experiment on kaolin-humic acid suspension and
synthetic dye wastewater. It shows that the optimal turbidity removal rate is 98.38%
when the dosage is 0.6mg/L, and the decolorization efficiency of Congo red and blue-
green GL is higher than 93% and 94%, respectively.
232
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
the molecular structure contains many functional groups such as carboxyl, amino, or
hydroxyl groups [71]. They are easily soluble in water, and have the characteristics of
flocculation, thickening, shearing, dispersibility, etc. Strong electric neutrality can
accelerate flocculation and precipitation. In order to make up for the shortcomings of
more residual inorganic coagulant and smaller molecular weight, inorganic-organic
composite polymer coagulant has developed rapidly.
The inorganic components of inorganic-organic composite flocculants are mostly studied
in iron salts and aluminum salts. The iron salts are mainly polyferric sulfate (PFS) and
polyferric chloride (PFC), and the aluminum salts are polyaluminum chloride (PAC).
Organic components mainly include artificial synthesis and natural organic
macromolecule polymers. The widely used synthetic organic high molecular polymers
include polyacrylamide (PAM), polyvinyl ether, sulfonated polyethylene and so on.
Natural organic polymer is the first flocculant discovered and used by humans, but due to
its properties of natural substances such as low molecular weight, low charge density, and
easily degraded by biodegradation, it is rarely used. Modification of natural organic
polymer flocculant can diversify its structure and enhance flocculation performance. In
addition, after modification, it is non-toxic or low-toxic, easy to biodegrade, does not
produce secondary pollution, and has low price and good quality with application
prospects [72].
The composite coagulant of aluminum salt and PAM is one of the most commonly used
inorganic-organic composite coagulants. Tang et al. [73] combined PAM with PAC,
ferric chloride, alum, and starch to treat the Yangtze River water. The results show that
PAM combined with PAC has the best flocculation effect, can effectively remove
suspended particles in water, and put the coagulant into use on the Yangtze River
passenger ship, which has produced considerable economic benefits. Pinotti et al. [74]
using PAC and PAM composite coagulants have strong electrical neutralization ability
and adsorption bridging performance, strong adsorption activity, compared with PAC, the
removal rate of organic matter can be improved More than 30%. Xue et al. [74] used
AlCl3-PAC-PAM composite coagulant to treat papermaking wastewater, and their
biochemical oxygen demand (BOD5) and chemical oxygen demand (COD) removal rates
were 58.9%, 63.4%, the removal rate of chroma is as high as 75%.
The composite coagulant made by PFS and PAM has the characteristics of low dosage,
fast settling and large floc particle size, etc. It has good coagulation and decolorization
effect in water treatment. Zeng et al. [76] used PFS-PAM composite coagulant and added
sodium diethyldithiocarbamate (DDTC) to treat copper electroplating wastewater, with a
copper removal rate exceeding 99.6%. Lee et al. [77] found that the coagulant prepared
by the composite of FeCl3 and non-ionic PAM has a better flocculation effect on
233
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
beverage industrial wastewater and produces less sludge than FeCl3 alone. The amount of
sludge produced is reduced by 60%.
Dimethyl diallyl ammonium chloride (DMDAAC) homopolymer (PDMDAAC) and its
copolymers are water-soluble cationic coagulants, with high charge density, easy to
control molecular weight, low price, and good flocculation effect. The combined use of
PDMDAAC and PAC can give full play to the synergistic effect of the two coagulants,
improve the flocculation effect, and reduce the treatment cost. Yue et al. [78] used
PDMDAAC, a copolymer of PDMDAAC and acrylamide (AM) [P(PDMDAAC-AM)]
and PAC to simulate the treatment of kaolin water samples. The results show that when
the dosage of PDMDAAC series coagulant is unchanged, the residual turbidity in water
gradually decreases with the increase of PAC dosage, and can reach the minimum value
when PAC is treated alone, that is, when a small amount of PAC is used It achieves a
better flocculation effect and simplifies the dosing and post-treatment process. The
composite coagulant of iron series and PDMDAAC has a better treatment effect on low
turbid water. Gao et al. [79] found that after PFC and PDMDAAC were combined, the
Zeta potential increased, and the effect of pH on the Zeta potential was weakened. In the
coagulation treatment of dye wastewater, PFC-PDMDAAC, PFC, and PDMDAAC were
added in a step-by-step comparison experiment. The results showed that PFC-
PDMDAAC had the highest removal rate of dye. Wei et al. [80] prepared composite
coagulants with PFS and PDMDAAC, and found that they have good removal effect on
pollutants in water, turbidity of surface water, organic matter, etc.
Modified natural organic polymer flocculants can be divided into starch derivatives,
chitin derivatives, natural vegetable gum modification, etc. according to different raw
materials. Among them, starch derivatives are widely used due to the advantages of easy
availability of raw materials and low prices. However, the treatment effect when used
alone is not ideal. Therefore, it is usually used in combination with inorganic flocculants.
Ekhtera et al. [81] used composite flocculants synthesized with aluminum-based
flocculants and corn starch to simulate the treatment of wastewater. It was found that not
only the dosage is reduced, but the turbidity removal effect is good, and the residual
amount of aluminum is lower. Ridgway et al. [82] used PAC and cationic modified starch
compound flocculant to treat oil refining wastewater, and found that the flocs formed
during the coagulation process were large, and significant turbidity removal could be
achieved with less dosage and degreasing effect. Chitosan (CTS) is a product of
deacetylation of chitin. It can achieve a better treatment effect on wastewater containing
metal ions such as chromium, copper, and zinc, but it is expensive and rarely used alone.
In order to reduce the treatment cost, PAC was used to prepare composite CTS
flocculant. Due to the poor electrical neutralization ability of the CTS molecule, it is also
234
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
greatly affected by acid and alkali. After the introduction of PAC, the positive charge on
the CTS molecular chain and the positive charge on the PAC are superimposed, which
significantly enhances the electrical neutralization of the composite flocculant Ability,
the flocculation effect has been greatly improved in the application of removing turbidity
and heavy metal ions, and the dosage is small, the sedimentation is fast, and the price is
low. Pereira et al. [83] used the prepared CTS composite flocculant to treat copper
smelting wastewater and found that not only the turbidity removal effect is good, but also
some heavy metals can be removed, and the removal rate is greater than 97%.
In the field of water treatment technology, polymerization, compounding, and
multifunctionalization have become the current development direction of coagulants.
Inorganic-organic polymer composite coagulant has the advantages of perfect preparation
technology, large processing capacity, good processing effect, high efficiency and low
energy, easy operation and wide application range. It has become the main direction of
research and application of composite coagulant. In the future, we should further study
the coagulation mechanism of inorganic-organic polymer composite coagulants, optimize
the synthesis process, expand the scope of compounding raw materials, give full play to
the synergistic effect of inorganic and organic components, and prepare highly targeted
and stable quality. High-efficiency, low-cost, green and environment-friendly composite
coagulant are best used in water treatment technology.
235
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
Among the many natural modified coagulants, chitosan and its derivatives have been
researched, developed and applied the most. Others include micro-natural modified
coagulants (mainly laboratory research), amphoteric flocculants, starch derivatives,
cellulose derivatives, lignin derivatives and cationic polyacrylamides [87]. Starch and
lignin flocculants have been poorly studied, because of their poor stability. The flocculant
containing chitosan and plant gum has been used and developed unprecedentedly in
recent years due to its versatility, biocompatibility and stability. The research directions
of natural polymer flocculants mainly focus on the following three aspects: First, improve
and stabilize the performance of existing natural polymer flocculants, and broaden its
application fields. The second is to develop a multifunctional natural polymer flocculant
mainly based on cationic groups [88]. The third is to develop and research a new type of
flocculant containing organic polymer-inorganic phase compound.
236
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
237
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
neutralized the net charge of the dye and caused the rapid removal of the dye. After
obtaining the optimal dose, the resuspension of the suspension occurred due to the
electrostatic repulsion between the charged particles. In the case of high pollutant
concentration, the bridging flocculation produced by the grafted acrylamide long chain
plays a key role.
At present, the mechanism of action of the modified chitosan flocculant is still in its
infancy, and the morphology and flocculation kinetics of the floc are lacking in-depth
exploration. Factors such as rearrangement of the internal structure of the floc, fractal
geometry of the floc and other factors are important factors [99]. The effect of model
accuracy has not been fully studied further. Use mathematical models to strengthen the
research on the influence of pH, ionic strength, dosage, temperature and other factors on
the modified chitosan flocculant, and explore the removal of new environmental
pollutants and multi-component pollutants by the synergistic effect of other water
treatment methods Potential, broaden the application range of modified chitosan
flocculant [100]. Most of the research on modified chitosan flocculants is still in the
small-scale laboratory test stage, so it is necessary to develop cheaper and more efficient
flocculants to promote future large-scale production and application.
238
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
charge state, there are many studies on cationic modified starch flocculants. Hacck et al.
[104] prepared 3-chloro-2-lightpropyltrimethylammonium chloride modified cationic
linear starch flocculant (St-CTA) by etherification method. Changing the dosage of
modifier can change the degree of cation substitution. Through the method of
flocculation conditioning, the St-CTA has a good dehydration effect on the suspension of
port sediments, and it is used in combination with anionic polyacrylamide to have a better
dehydration effect. In the research of Liu et al. [105], this synthesis method was also
adopted to prepare a series of St-CTA with different degrees of substitution, and the
simultaneous deturbidity and antibacterial performance were investigated. The study
found that St-CTA has the dual performance of simultaneously removing turbidity and
bacteriostasis. When kaolin and bacteria in water coexist, its flocculation removal has a
certain synergistic enhancement effect. The quaternary ammonium salt cation has a
strong positive charge property, has the effect of destroying the cell wall of the cell body,
and has a significant effect on the cell wall of the Gram-negative bacteria.
Huang et al. [106] prepared methacryloyloxyethyl graft-modified cationic starch
flocculant (St-g-PDMC) by grafting method. The copolymer was dehydrated and
precipitated by acetone Down, you can improve the purity of the product and reduce
toxicity. Compared with starch and polyacrylamide, St-g-PDMC has a good flocculation
and purification effect on kaolin suspension. In the low dosage range, the electrical
neutralization played a leading role in the flocculation process. In addition, St-g-PDMC
can also regulate and dehydrate anaerobic sludge. The conditioned sludge can be easily
filtered out, and the dosage is 0.696% of the dry weight of the sludge. St-g-PDMC has
very good application prospects for sewage treatment and sludge conditioning. The
quaternization of starch can make it have the dual functions of turbidity removal and
bacteriostasis, showing broad application prospects.
239
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
polyacrylamide. In the study of Shaabani et al. [109], a sulfonated cellulose was prepared
by modifying cotton, using alum as a coagulant, and the sulfonated cellulose as a
flocculant, coagulating. After purifying the kaolin suspension and optimizing it by
response surface method, the dosage of alum has been reduced. It believes that sulfonated
cellulose can be used as a substitute for traditional flocculants. In the study of Suopajarvi
et al. [110], an anionic dicarboxylic acid nanocellulose was prepared and used as a
flocculant and ferric sulfate as a coagulant to treat municipal wastewater. In the combined
use of coagulation and flocculation, the turbidity and COD of the effluent are low, and
the dosage of ferric sulfate can be effectively reduced. The anionic dicarboxylic acid
nanocellulose exhibits higher stability and wider pH adaptation range in long-term use. In
another study by Suopajarvi et al. [111], two types of cationic nanocellulose with
different charge densities were prepared by modifying the cellulose of trees. The charge
densities were 1.07 and 1.70 mmol/g, respectively. The performance of the cationic
nanocellulose on municipal sludge conditioning was investigated and compared with
cationic polyacrylamide. The results show that the cationic nanocellulose can effectively
condition municipal sludge, and its dosage is close to polyacrylamide. In terms of
turbidity removal, the performance of cationic nanocellulose is close to that of cationic
polyacrylamide. In terms of COD removal, the performance of cationic nanocellulose is
higher than that of cationic polyacrylamide [112].
Conclusion
The potential applications of inorganic polymer coagulants, synthetic polymer
coagulants, organic/inorganic composite coagulants and natural modified coagulants in
wastewater treatment have been summarized in depth. In some studies, it has a significant
removal effect on water quality parameters such as suspended solids, turbidity, COD and
color, and the removal rate is generally more than 90%. As far as traditional inorganic
coagulants are concerned, due to the high complexity of the flocculation process and the
variety of polyelectrolytes available, there are still few industrial practices for
optimization of flocculation. One way to optimize the flocculation process is to select or
control the molecular weight and charge density range of the polymer. Different
molecular weights and charge densities produce different flocculation mechanisms.
Research is needed to investigate how molecular weight and charge density distribution
affect flocculation performance in order to provide better flocculant choices for specific
industrial applications. Optimizing these factors can significantly improve processing
efficiency and reduce chemical costs.
Since the use of conventional flocculants is closely related to environmental pollution and
health hazards, it is necessary to synthesize environmentally friendly, economically
240
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
viable flocculants with high flocculation efficiency. Some of the developed natural
modified coagulants have good flocculation performance, and have excellent removal
effects on suspended solids, turbidity, COD and color in various wastewaters. According
to the actual industrial production and application, the cost-benefit analysis and
optimization of natural modified coagulants are needed to produce a standard production
protocol and maximize the flocculation efficiency. It is necessary to judge the economics
of its actual use. In addition, the work carried out on an industrial scale is very limited,
focusing mainly on laboratory testing. Finally, choosing a high-efficiency flocculant that
can remove or reduce almost all pollutants in wastewater is the key to the success of the
flocculation process. From two aspects of performance and cost of flocculant, it is a
promising flocculant material to produce environmentally friendly flocculant with high
removal rate and high concentration flocculant by simple, economical and feasible
process.
References
[1] H. Zheng, Y. Sun, C. Zhu, J. Guo, C. Zhao, Y. Liao, and Q. Guan, UV-initiated
polymerization of hydrophobically associating cationic flocculants: Synthesis,
characterization, and dewatering properties. Chem. Eng. J. 234 (2013) 318-326.
https://doi.org/10.1016/j.cej.2013.08.098
[2] Y.J. Sun, H.L. Zheng, M.Z. Tan, J.Y. Ma, W. Fan, and Y. Liao, Synthesis and
Application of Hydrophobically Associating Cationic Polyacrylamide. Asian Journal
of Chemistry 26 (2014) 3769-3773. https://doi.org/10.14233/ajchem.2014.15948
[3] H. Zheng, Y. Sun, J. Guo, F. Li, W. Fan, Y. Liao, and Q. Guan, Characterization and
Evaluation of Dewatering Properties of PADB, a Highly Efficient Cationic Flocculant.
Ind. Eng. Chem. Res. 53 (2014) 2572-2582. https://doi.org/10.1021/ie403635y
[4] S. Li, Z. Wu, H. Tang, and J. Yang, Selective adsorption of protein on micropatterned
flexible poly(ethylene terephthalate) surfaces modified by vacuum ultraviolet
lithography. Appl. Surf. Sci. 258 (2012) 4222-4227.
https://doi.org/10.1016/j.apsusc.2011.12.027
[5] C.S. Lee, J. Robinson, and M.F. Chong, A review on application of flocculants in
wastewater treatment. Process Saf. Environ. 92 (2014) 489-508.
https://doi.org/10.1016/j.psep.2014.04.010
[6] J. Wang, J. Yang, H.W. Zhang, W.S. Guo, and H.H. Ngo, Feasibility study on
magnetic enhanced flocculation for mitigating membrane fouling. J. Ind. Eng. Chem.
26 (2015) 37-45. https://doi.org/10.1016/j.jiec.2014.11.038
241
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
242
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
[17] Y. Sun, A. Chen, W. Sun, K.J. Shah, H. Zheng, and C. Zhu, Removal of Cu and Cr
ions from aqueous solutions by a chitosan-based flocculant. Desalin. Water Treat. 148
(2019) 259-269. https://doi.org/10.5004/dwt.2019.23953
[18] J. Ma, K. Fu, X. Fu, Q. Guan, L. Ding, J. Shi, G. Zhu, X. Zhang, S. Zhang, and L.
Jiang, Flocculation properties and kinetic investigation of polyacrylamide with
different cationic monomer content for high turbid water purification. Sep. Purif.
Technol. 182 (2017) 134-143. https://doi.org/10.1016/j.seppur.2017.03.048
[19] X. Zhang, J. Ma, K. Fu, X. Fu, L. Ding, Q. Guan, J. Shi, and L. Jiang, Research on
Synthesis of Nano Chitosan modified Polyacrylamide through Low-pressure
Ultraviolet Initiation. J. Polym. Mater. 34 (2017) 129-143.
[20] J. Ma, K. Fu, J. Shi, Y. Sun, X. Zhang, and L. Ding, Ultraviolet-assisted synthesis of
polyacrylamide-grafted chitosan nanoparticles and flocculation performance.
Carbohyd. Polym. 151 (2016) 565-575. https://doi.org/10.1016/j.carbpol.2016.06.002
[21] H. Zheng, G. Zhu, S. Jiang, T. Tshukudu, X. Xiang, P. Zhang, and Q. He,
Investigations of coagulation-flocculation process by performance optimization, model
prediction and fractal structure of flocs. Desalination 269 (2011) 148-156.
https://doi.org/10.1016/j.desal.2010.10.054
[22] G. Zhu, H. Zheng, Z. Zhang, T. Tshukudu, P. Zhang, and X. Xiang, Characterization
and coagulation-flocculation behavior of polymeric aluminum ferric sulfate (PAFS).
Chem. Eng. J. 178 (2011) 50-59. https://doi.org/10.1016/j.cej.2011.10.008
[23] P. Luting, and W. Jinfeng, Research and progress of the preparation technologies of
polyferric sulphate [J]. Industrial Water Treatment 9 (2009) 147-150.
[24] C. Liu, Y. He, F. Li, and H. Wang, Preparation of poly ferric sulfate and the
application in micro-polluted raw water treatment. Journal of the Chinese Advanced
Materials Society 1 (2013) 210-218. https://doi.org/10.1080/22243682.2013.835120
[25] G. Zhu, H. Zheng, W. Chen, W. Fan, P. Zhang, and T. Tshukudu, Preparation of a
composite coagulant: Polymeric aluminum ferric sulfate (PAFS) for wastewater
treatment. Desalination 285 (2012) 315-323.
https://doi.org/10.1016/j.desal.2011.10.019
[26] Z. Yang, X. Lu, B. Gao, Y. Wang, Q. Yue, and T. Chen, Fabrication and
characterization of poly (ferric chloride)-polyamine flocculant and its application to
the decolorization of reactive dyes. J. Mater. Sci. 49 (2014) 4962-4972.
https://doi.org/10.1007/s10853-014-8197-0
243
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
[27] X. Sheng, Study on Poly Ferric Chloride from Steel Pickling Acid Waste. Shandong
Chemical Industry 6 (2012) 10.
[28] T. Tshukudu, H.L. Zheng, X.B. Hua, J. Yang, M.Z. Tan, J.Y. Ma, Y.J. Sun, and
G.C. Zhu, Response surface methodology approach to optimize coagulation-
flocculation process using composite coagulants. Korean J. Chem. Eng. 30 (2013)
649-657. https://doi.org/10.1007/s11814-012-0169-y
[29] W. Zhang, L. Yao, J. Ma, and D. Li, Study on Preparation and Flocculation
Properties of Inorganic Polymer Flocculant Polyferric Silicate Sulfate (PFSS), 2010
4th International Conference on Bioinformatics and Biomedical Engineering, IEEE,
Chengdu, 2010, pp. 1-4. https://doi.org/10.1109/ICBBE.2010.5517958
[30] T. Tshukudu, H. Zheng, and J. Yang, Optimization of Coagulation with PFS-
PDADMAC Composite Coagulants Using the Response Surface Methodology
Experimental Design Technique. Water Environ. Res. 85 (2013) 456-465.
https://doi.org/10.2175/106143012X13560205144515
[31] T. Tshukudu, H. Zheng, X. Hua, J. Yang, M. Tan, J. Ma, Y. Sun, and G. Zhu,
Response surface methodology approach to optimize coagulation-flocculation process
using composite coagulants. Korean J. Chem. Eng. 30 (2013) 649-657.
https://doi.org/10.1007/s11814-012-0169-y
[32] J. Shi, Q. Liu, and D.S. Wang, Studies on the realationship between the speciation
distribution and Si/Fe ratio of poly-silica-ferric-chloride, Advanced Materials
Research, Trans Tech Publ, Wu Han, 2011, pp. 1339-1342.
https://doi.org/10.4028/www.scientific.net/AMR.156-157.1339
[33] C. Jian, Research Progress of Inorganic Polymer Flocculants. Journal of Langfang
Teachers University (Natural Science Edition) 16 (2016) 70-72.
[34] H.L. Zheng, J.Y. Ma, C.J. Zhu, Z. Zhang, L.W. Liu, Y.J. Sun, and X.M. Tang,
Synthesis of anion polyacrylamide under UV initiation and its application in removing
dioctyl phthalate from water through flocculation process. Sep. Purif. Technol. 123
(2014) 35-44. https://doi.org/10.1016/j.seppur.2013.12.018
[35] L. Zhang, Y. Zeng, and Z. Cheng, Removal of heavy metal ions using chitosan and
modified chitosan: A review. J. Mol. Liq. 214 (2016) 175-191.
https://doi.org/10.1016/j.molliq.2015.12.013
[36] R. Wang, K. Sun, J. Wang, Y. He, P. Song, and Y. Xiong, Preparation and
Application of Natural Polymer/Hydroxyapatite Composite. Prog. Chem. 28 (2016)
885-895.
244
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
[37] C. Feng, X. Ge, D. Wang, and H. Tang, Effect of aging condition on species
transformation in polymeric Al salt coagulants. Colloid. Surface. A. 379 (2011) 62-69.
https://doi.org/10.1016/j.colsurfa.2010.11.046
[38] C. Feng, H. Tang, and D. Wang, Differentiation of hydroxyl-aluminum species at
lower OH/Al ratios by combination of 27Al NMR and Ferron assay improved with
kinetic resolution. Colloid. Surface. A. 305 (2007) 76-82.
https://doi.org/10.1016/j.colsurfa.2007.04.043
[39] B. Shi, G. Li, D. Wang, C. Feng, and H. Tang, Removal of direct dyes by
coagulation: The performance of preformed polymeric aluminum species. J. Hazard.
Mater. 143 (2007) 567-574. https://doi.org/10.1016/j.jhazmat.2006.09.076
[40] B. Shi, Q. Wei, D. Wang, Z. Zhu, and H. Tang, Coagulation of humic acid: The
performance of preformed and non-preformed Al species. Colloid. Surface. A. 296
(2007) 141-148. https://doi.org/10.1016/j.colsurfa.2006.09.037
[41] B. Shi, G. Li, D. Wang, and H. Tang, Separation of Al-13 from polyaluminum
chloride by sulfate precipitation and nitrate metathesis. Sep. Purif. Technol. 54 (2007)
88-95. https://doi.org/10.1016/j.seppur.2006.08.011
[42] C. Ye, D. Wang, B. Shi, J. Yu, J. Qu, M. Edwards, and H. Tang, Alkalinity effect of
coagulation with polyaluminum chlorides: Role of electrostatic patch. Colloid.
Surface. A. 294 (2007) 163-173. https://doi.org/10.1016/j.colsurfa.2006.08.005
[43] X. Wu, X. Ge, D. Wang, and H. Tang, Distinct coagulation mechanism and model
between alum and high Al-13-PACl. Colloid. Surface. A. 305 (2007) 89-96.
https://doi.org/10.1016/j.colsurfa.2007.04.046
[44] H. Tang, F. Xiao, and D. Wang, Speciation, stability, and coagulation mechanisms
of hydroxyl aluminum clusters formed by PACl and alum: A critical review. Adv.
Colloid Interfac. 226 (2015) 78-85. https://doi.org/10.1016/j.cis.2015.09.002
[45] X. Wu, C. Ye, D. Wang, X. Ge, and H. Tang, Effect of speciation transformation on
the coagulation behavior of Al-13 and Al-13 aggregates. Water Sci. Technol. 59
(2009) 815-822. https://doi.org/10.2166/wst.2009.064
[46] H. Liu, D. Wang, M. Wang, H. Tang, and M. Yang, Effect of pre-ozonation on
coagulation with IPF-PACls: Role of coagulant speciation. Colloid. Surface. A. 294
(2007) 111-116. https://doi.org/10.1016/j.colsurfa.2006.08.008
[47] Z. Bi, C. Feng, D. Wang, X. Ge, and H. Tang, Transformation of planar Mogel Al-
13 to epsilon Keggin Al-13 in dissolution process. Colloid. Surface. A. 407 (2012) 91-
98. https://doi.org/10.1016/j.colsurfa.2012.05.013
245
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
[48] J. Cao, Z. Wu, S. Li, H. Tang, and Q. Mei, Site-selective adsorption of protein
induced by a metal pattern on a poly(ethylene terephthalate) surface. Colloid. Surface.
B. 111 (2013) 418-422. https://doi.org/10.1016/j.colsurfb.2013.06.023
[49] C. Feng, Q. Wei, S. Wang, B. Shi, and H. Tang, Speciation of hydroxyl-Al polymers
formed through simultaneous hydrolysis of aluminum salts and urea. Colloid. Surface.
A. 303 (2007) 241-248. https://doi.org/10.1016/j.colsurfa.2007.04.005
[50] T. Li, Z. Zhu, D. Wang, C. Yao, and H. Tang, The strength and fractal dimension
characteristics of alum-kaolin flocs. Int. J. Miner. Process. 82 (2007) 23-29.
https://doi.org/10.1016/j.minpro.2006.09.012
[51] Y. Wang, H. Zhou, F. Yu, B. Shi, and H. Tang, Fractal adsorption characteristics of
complex molecules on particles - A case study of dyes onto granular activated carbon
(GAC). Colloid. Surface. A. 299 (2007) 224-231.
https://doi.org/10.1016/j.colsurfa.2006.11.044
[52] T. Li, D. Wang, B. Zhang, H. Liu, and H. Tang, Morphological characterization of
suspended particles under wind-induced disturbance in Taihu Lake, China. Environ.
Monit. Assess. 127 (2007) 79-86. https://doi.org/10.1007/s10661-006-9261-2
[53] X. Wu, D. Wang, X. Ge, and H. Tang, Coagulation of silica microspheres with
hydrolyzed Al(III)-Significance of Al-13 and Al-13 aggregates. Colloid. Surface. A.
330 (2008) 72-79. https://doi.org/10.1016/j.colsurfa.2008.07.034
[54] D. Wang, J. Gregory, and H. Tang, Mechanistic difference of coagulation of kaolin
between PACl and cationic polyelectrolytes: A comparative study on zone 2
coagulation. Dry. Technol. 26 (2008) 1060-1067.
https://doi.org/10.1080/07373930802179327
[55] C. Feng, S. Zhao, Z. Bi, D. Wang, and H. Tang, Speciation of prehydrolyzed Al salt
coagulants with electrospray ionization time-of-flight mass spectrometry and Al-27
NMR spectroscopy. Colloid. Surface. A. 392 (2011) 95-102.
https://doi.org/10.1016/j.colsurfa.2011.09.039
[56] Y. Sun, M. Ren, W. Sun, X. Xiao, Y. Xu, H. Zheng, H. Wu, Z. Liu, and H. Zhu,
Plasma-induced synthesis of chitosan-g-polyacrylamide and its flocculation
performance for algae removal. Environ. Technol. 40 (2017) 954-968.
https://doi.org/10.1080/09593330.2017.1414312
[57] Y. Sun, J. Liu, W. Sun, H. Zheng, and K.J. Shah, An alternative strategy for
enhanced algae removal by cationic chitosan-based flocculants. Desalin. Water Treat.
167 (2019) 13-26. https://doi.org/10.5004/dwt.2019.24636
246
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
[58] X. Xiao, Y. Sun, W. Sun, H. Shen, H. Zheng, Y. Xu, J. Zhao, H. Wu, and C. Liu,
Advanced treatment of actual textile dye wastewater by Fenton-flocculation process.
The Canadian Journal of Chemical Engineering 95 (2017) 1245-1252.
https://doi.org/10.1002/cjce.22752
[59] L. Feng, J. Liu, C. Xu, W. Lu, D. Li, C. Zhao, B. Liu, X. Li, S. Khan, H. Zheng, and
Y. Sun, Better understanding the polymerization kinetics of ultrasonic-template
method and new insight on sludge floc characteristics research. Sci. Total Environ.
689 (2019) 546-556. https://doi.org/10.1016/j.scitotenv.2019.06.475
[60] S. Zhang, H. Zheng, X. Tang, Y. Sun, Y. Wu, X. Zheng, and Q. Sun, Evaluation a
self-assembled anionic polyacrylamide flocculant for the treatment of hematite
wastewater: Role of microblock structure. J. Taiwan Inst. Chem. E. 95 (2019) 11-20.
https://doi.org/10.1016/j.jtice.2018.09.030
[61] L. Feng, J. Liu, C. Xu, W. Lu, D. Li, C. Zhao, B. Liu, X. Li, S. Khan, H. Zheng, and
Y. Sun, Better understanding the polymerization kinetics of ultrasonic-template
method and new insight on sludge floc characteristics research. The Science of the
total environment 689 (2019) 546-556. https://doi.org/10.1016/j.scitotenv.2019.06.475
[62] Y. Sun, K.J. Shah, W. Sun, and H. Zheng, Performance evaluation of chitosan-based
flocculants with good pH resistance and high heavy metals removal capacity. Sep.
Purif. Technol. 215 (2019) 208-216. https://doi.org/10.1016/j.seppur.2019.01.017
[63] Y. Sun, W. Sun, K.J. Shah, P. Chiang, and H. Zheng, Characterization and
flocculation evaluation of a novel carboxylated chitosan modified flocculant by UV
initiated polymerization. Carbohyd. Polym. 208 (2019) 213-220.
https://doi.org/10.1016/j.carbpol.2018.12.064
[64] K. Xu, Y. Liu, Y. Wang, Y. Tan, X. Liang, C. Lu, H. Wang, X. Liu, and P. Wang, A
novel poly (acrylic acid-co-acrylamide)/diatomite composite flocculant with
outstanding flocculation performance. Water Sci. Technol. 72 (2015) 889-895.
https://doi.org/10.2166/wst.2015.290
[65] J. Li, J. Li, X. Liu, Z. Du, and F. Cheng, Effect of silicon content on preparation and
coagulation performance of poly-silicic-metal coagulants derived from coal gangue for
coking wastewater treatment. Sep. Purif. Technol. 202 (2018) 149-156.
https://doi.org/10.1016/j.seppur.2018.03.055
[66] X. Xiong, L. Wei, X.U. Xia, and D. Yan, Synthesis of Polymeric Hybrid Flocculant
PSAF-CPAM and its Phosphorus Removal in Printing and Dyeing Wastewater.
Industrial Safety and Environmental Protection 6 (2018) 21.
247
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
[67] Y. Sun, H. Zheng, M. Tan, Y. Wang, X. Tang, L.I. Feng, and X. Xiang, Synthesis
and characterization of composite flocculant PAFS-CPAM for the treatment of textile
dye wastewater. J. Appl. Polym. Sci. 131 (2014) 156-161.
https://doi.org/10.1002/app.40062
[68] H. Salehizadeh, N. Yan, and R. Farnood, Recent advances in polysaccharide bio-
based flocculants. Biotechnol. Adv. 36 (2018) 92-119.
https://doi.org/10.1016/j.biotechadv.2017.10.002
[69] M. Sillanpaa, M.C. Ncibi, A. Matilainen, and M. Vepsalainen, Removal of natural
organic matter in drinking water treatment by coagulation: A comprehensive review.
Chemosphere 190 (2018) 54-71. https://doi.org/10.1016/j.chemosphere.2017.09.113
[70] J. Desbrières, and E. Guibal, Chitosan for wastewater treatment. Polym. Int. 67
(2018) 7-14. https://doi.org/10.1002/pi.5464
[71] L.Y. Chai, Q.Z. Li, Q.W. Wang, and X. Yan, Solid-liquid separation: an emerging
issue in heavy metal wastewater treatment. Environ. Sci. Pollut. R. 25 (2018) 17250-
17267. https://doi.org/10.1007/s11356-018-2135-7
[72] P. Kanmani, J. Aravind, M. Kamaraj, P. Sureshbabu, and S. Karthikeyan,
Environmental applications of chitosan and cellulosic biopolymers: A comprehensive
outlook. Bioresource Technol. 242 (2017) 295-303.
https://doi.org/10.1016/j.biortech.2017.03.119
[73] Q. Tang, J. Wu, J. Lin, Q. Li, and S. Fan, Two-step synthesis of
polyacrylamide/polyacrylate interpenetrating network hydrogels and its
swelling/deswelling properties. J. Mater. Sci. 43 (2008) 5884-5890.
https://doi.org/10.1007/s10853-008-2857-x
[74] A. Pinotti, and N. Zaritzky, Effect of aluminum sulfate and cationic polyelectrolytes
on the destabilization of emulsified wastes. Waste Manage. 21 (2001) 535-542.
https://doi.org/10.1016/S0956-053X(00)00110-0
[75] M.X. Xue, B.Y. Gao, X. Xu, and W. Song, Polyamidine as a New-Style Coagulant
Aid for Dye Wastewater Treatment and its Floc Characteristics, Materials Science
Forum, Trans Tech Publ, Singapore, 2018, pp. 930-940.
https://doi.org/10.4028/www.scientific.net/MSF.913.930
[76] K. Zeng, W. Qin, F. Jiao, M. He, and L. Kong, Treatment of mine drainage
generated by lead-zinc concentration plant. J. Cent. South Univ. 21 (2014) 1453-1460.
https://doi.org/10.1007/s11771-014-2085-2
248
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
[77] K.E. Lee, T.T. Teng, N. Morad, B.T. Poh, and M. Mahalingam, Flocculation activity
of novel ferric chloride-polyacrylamide (FeCl3-PAM) hybrid polymer. Desalination
266 (2011) 108-113. https://doi.org/10.1016/j.desal.2010.08.009
[78] Q. YUE, Y. LI, B. GAO, Z. YANG, and X. ZOU, Study on the inverse emulsion
polymerization of PDMDAAC-AM [J]. Journal of Shandong University (Natural
Science) 6 (2004) 120-125.
[79] B. Gao, Y. Wang, Q. Yue, J. Wei, and Q. Li, Color removal from simulated dye
water and actual textile wastewater using a composite coagulant prepared by ployferric
chloride and polydimethyldiallylammonium chloride. Sep. Purif. Technol. 54 (2007)
157-163. https://doi.org/10.1016/j.seppur.2006.08.026
[80] J.C. Wei, B.Y. Gao, Q.Y. Yue, Y. Wang, and L. Lu, Performance and mechanism of
polyferric-quaternary ammonium salt composite flocculants in treating high organic
matter and high alkalinity surface water. J. Hazard. Mater. 165 (2009) 789-795.
https://doi.org/10.1016/j.jhazmat.2008.10.069
[81] M.H. Ekhtera, P.R. Charani, O. Ramezani, and M. Azadfallah, EFFECTS OF
POLY-ALUMINUM CHLORIDE, STARCH, ALUM AND ROSIN ON THE ROSIN
SIZING, STRENGTH AND MICROSCOPIC APPEARANCE OF PAPER
PREPARED FROM OLD CORRUGATED CONTAINER (OCC) PULP.
BioResources 3 (2008) 383-402.
[82] C.J. Ridgway, and P.A. Gane, Size-selective absorption and adsorption in anionic
pigmented porous coating structures: case study cationic starch polymer versus
nanofibrillated cellulose. Cellulose 20 (2013) 933-951. https://doi.org/10.1007/s10570-
013-9878-6
[83] F. Pereira, K.S. Sousa, G. Cavalcanti, M.G. Fonseca, A.G. de Souza, and A. Alves,
Chitosan-montmorillonite biocomposite as an adsorbent for copper (II) cations from
aqueous solutions. Int. J. Biol. Macromol. 61 (2013) 471-478.
https://doi.org/10.1016/j.ijbiomac.2013.08.017
[84] Y. Sun, S. Zhou, S. Pan, S. Zhu, Y. Yu, and H. Zheng, Performance evaluation and
optimization of flocculation process for removing heavy metal. Chem. Eng. J. 385
(2020) 123911. https://doi.org/10.1016/j.cej.2019.123911
[85] Y. Sun, S. Zhou, W. Sun, S. Zhu, and H. Zheng, Flocculation activity and evaluation
of chitosan-based flocculant CMCTS-g-P(AM-CA) for heavy metal removal. Sep.
Purif. Technol. 241 (2020) 116737. https://doi.org/10.1016/j.seppur.2020.116737
249
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
[86] P. Wu, J. Yi, L. Feng, X. Li, Y. Chen, Z. Liu, S. Tian, S. Li, S. Khan, and Y. Sun,
Microwave assisted preparation and characterization of a chitosan based flocculant for
the application and evaluation of sludge flocculation and dewatering. Int. J. Biol.
Macromol. 155 (2020) 708-720. https://doi.org/10.1016/j.ijbiomac.2020.04.011
[87] Y. Sun, A. Chen, W. Sun, K.J. Shah, H. Zheng, and C. Zhu, Removal of Cu and Cr
ions from aqueous solutions by a chitosan based flocculant. Desalin. Water Treat. 148
(2019) 259-269. https://doi.org/10.5004/dwt.2019.23953
[88] H. Wei, B.Q. Gao, J. Ren, A.M. Li, and H. Yang, Coagulation/flocculation in
dewatering of sludge: A review. Water Res. 143 (2018) 608-631.
https://doi.org/10.1016/j.watres.2018.07.029
[89] Y. Sun, A. Chen, S. Pan, W. Sun, C. Zhu, K.J. Shah, and H. Zheng, Novel chitosan-
based flocculants for chromium and nickle removal in wastewater via integrated
chelation and flocculation. J. Environ. Manage. 248 (2019) 109241.
https://doi.org/10.1016/j.jenvman.2019.07.012
[90] L. Chen, Y. Sun, W. Sun, K.J. Shah, Y. Xu, and H. Zheng, Efficient cationic
flocculant MHCS-g-P(AM-DAC) synthesized by UV-induced polymerization for
algae removal. Sep. Purif. Technol. 210 (2019) 10-19.
https://doi.org/10.1016/j.seppur.2018.07.090
[91] Z. You, C. Zhuang, Y. Sun, S. Zhang, and H. Zheng, Efficient Removal of TiO2
Nanoparticles by Enhanced Flocculation-Coagulation. Ind. Eng. Chem. Res. 58 (2019)
14528-14537. https://doi.org/10.1021/acs.iecr.9b01504
[92] S. Jia, Z. Yang, W. Yang, T. Zhang, S. Zhang, X. Yang, Y. Dong, J. Wu, and Y.
Wang, Removal of Cu (II) and tetracycline using an aromatic rings-functionalized
chitosan-based flocculant: enhanced interaction between the flocculant and the
antibiotic. Chem. Eng. J. 283 (2016) 495-503.
https://doi.org/10.1016/j.cej.2015.08.003
[93] H. Ge, H. Chen, and S. Huang, Microwave preparation and properties of O‐
crosslinked maleic acyl chitosan adsorbent for Pb2+ and Cu2+. J. Appl. Polym. Sci.
125 (2012) 2716-2723. https://doi.org/10.1002/app.36588
[94] M. Sugimoto, M. Morimoto, H. Sashiwa, H. Saimoto, and Y. Shigemasa,
Preparation and characterization of water-soluble chitin and chitosan derivatives.
Carbohyd. Polym. 36 (1998) 49-59. https://doi.org/10.1016/S0144-8617(97)00235-X
250
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
251
Advances in Wastewater Treatment I Materials Research Forum LLC
Materials Research Foundations 91 (2021) 219-252 https://doi.org/10.21741/9781644901144-7
https://doi.org/10.1002/1439-2054(20020801)287:8<495::AID-MAME495>3.0.CO;2-
K
[105] Z. Liu, M. Huang, A. Li, and H. Yang, Flocculation and antimicrobial properties of
a cationized starch. Water Res. 119 (2017) 57-66.
https://doi.org/10.1016/j.watres.2017.04.043
[106] M. Huang, Z. Liu, A. Li, and H. Yang, Dual functionality of a graft starch
flocculant: Flocculation and antibacterial performance. J. Environ. Manage. 196
(2017) 63-71. https://doi.org/10.1016/j.jenvman.2017.02.078
[107] W. Sun, G. Ma, Y. Sun, Y. Liu, N. Song, Y. Xu, and H. Zheng, Effective treatment
of high phosphorus pharmaceutical wastewater by chemical precipitation. The
Canadian Journal of Chemical Engineering 95 (2017) 1585-1593.
https://doi.org/10.1002/cjce.22799
[108] S. Mansouri, R. Khiari, F. Bettaieb, A.A. El-Gendy, and F. Mhenni, Synthesis and
characterization of carboxymethyl cellulose from tunisian vine stem: study of water
absorption and retention capacities. J. Polym. Environ. 23 (2015) 190-198.
https://doi.org/10.1007/s10924-014-0691-6
[109] A. Shaabani, A. Rahmati, and Z. Badri, Sulfonated cellulose and starch: New
biodegradable and renewable solid acid catalysts for efficient synthesis of quinolines.
Catal. Commun. 9 (2008) 13-16. https://doi.org/10.1016/j.catcom.2007.05.021
[110] S. Hokkanen, E. Repo, T. Suopajärvi, H. Liimatainen, J. Niinimaa, and M.
Sillanpää, Adsorption of Ni (II), Cu (II) and Cd (II) from aqueous solutions by amino
modified nanostructured microfibrillated cellulose. Cellulose 21 (2014) 1471-1487.
https://doi.org/10.1007/s10570-014-0240-4
[111] T. Suopajärvi, H. Liimatainen, M. Karjalainen, H. Upola, and J. Niinimäki, Lead
adsorption with sulfonated wheat pulp nanocelluloses. Journal of Water Process
Engineering 5 (2015) 136-142. https://doi.org/10.1016/j.jwpe.2014.06.003
[112] Y. Sun, M. Ren, C. Zhu, Y. Xu, H. Zheng, X. Xiao, H. Wu, T. Xia, and Z. You,
UV-Initiated Graft Copolymerization of Cationic Chitosan-Based Flocculants for
Treatment of Zinc Phosphate-Contaminated Wastewater. Ind. Eng. Chem. Res. 55
(2016) 10025-10035. https://doi.org/10.1021/acs.iecr.6b02855
252
View publication stats