X300 Rinstrum
X300 Rinstrum
X300 Rinstrum
Digital Indicator
Quick Start Manual
003X-610-100-M03
Copyright
All Rights Reserved. No part of this document may be
copied, reproduced, republished, uploaded, posted,
transmitted, distributed, stored in or introduced into a
retrieval system in any form, or by any means (electronic,
mechanical, photocopying, recording or otherwise)
whatsoever without prior written permission of
Rinstrum Pty Ltd.
Disclaimer
Rinstrum Pty Ltd reserves the right to make changes
to the products contained in this manual in order
to improve design, performance or reliability.
The information in this manual is believed to be accurate in
all respects at the time of publication, but is subject to
change without notice. Rinstrum Pty Ltd assumes no
responsibility for any errors or omissions and disclaims
responsibility for any consequences resulting from the use
of the information provided herein.
SPECIAL NOTE
Trade Use of the Instrument
This manual may occasionally make reference to
Trade Use settings of the instrument.
Some individual settings may not be legal for trade use.
Please check regulations with the appropriate
Weights and Measures Authority.
Quick Start Manual Rev 1.33
Table of Contents
1. INTRODUCTION.............................................................2
1.1. Approvals................................................................2
1.2. Manuals ..................................................................2
2. SHIPPING CONTENTS ..................................................2
3. SPECIFICATIONS ..........................................................3
4. WARNINGS ....................................................................4
4.1. General ...................................................................4
4.2. Configuration Issues ...............................................4
5. INSTALLATION ..............................................................5
5.1. Electrical Safety ......................................................5
5.2. opto-LINK................................................................6
6. CONNECTIONS..............................................................7
6.1. Cable Connections .................................................7
6.2. DC Power (DC PWR + , DC PWR –)......................7
6.3. Load Cell Connection .............................................7
6.4. Auxiliary Connections .............................................9
6.5. Connecting Shields...............................................15
6.6. Regulatory Sealing Requirements........................15
7. INSTRUMENT SETUP..................................................17
7.1. Calibration Counter...............................................17
7.2. opto-LINK..............................................................17
7.3. Access Full Setup .................................................18
7.4. Access Safe Setup ...............................................18
7.5. Exit Full or Safe Setup ..........................................18
7.6. Settings.................................................................18
8. ERROR MESSAGES ....................................................27
8.1. Weighing Errors ....................................................27
8.2. Setup and Calibration Errors ................................28
8.3. Diagnostic Errors ..................................................29
003X-608-133 Page 1
Quick Start Manual Rev 1.33
1. Introduction
This manual contains information on the installation, calibration
and setup of the instrument.
1.1. Approvals
• C-tick approved and CE approved.
1.1.1. Trade versions
• NSC approval (4000 divisions at 0.8µV/division).
• NMI approval (4000 divisions at 0.8µV/division).
• NTEP approval (10000 divisions at 0.8µV/division).
1.2. Manuals
For more information on this instrument refer to the
Reference Manual, Quick Start Manual or
Communications Manual.
2. Shipping Contents
The following table identifies the items shipped with the
indicator. Please check that your packing box contains the
specified items.
Shipped Items Other Items (Optional)
• Indicator • opto-LINK Cable
• Operator Manual • Power Supply
• Quick Start Manual • Battery Pack with Charger
• Trade Label (plastic) • Captive Security Screws
• U Bracket
Page 2 003X-608-133
Quick Start Manual Rev 1.33
3. Specifications
Performance
Resolution Up to 30,000 divisions, minimum of 0.25µV/division
(K307 up to 60,000 divisions)
Zero Cancellation 2.0mV/V
Span Adjustment 0.1mV/V to 3.0mV/V full scale
Stability/Drift Zero: < 0.1µV/°C (+ 8ppm of deadload max)
Span < 8 ppm/°C, Linearity < 20ppm, Noise < 0.2µVp-p
Excitation 5 volts for up to 4 x 350 or 8 x 700 ohm load cells (4-wire or
6-wire plus shield)
Maximum total load cell resistance: 1,000 ohms
A/D Type 24bit Sigma Delta with 8,388,608 internal counts
A/D Conversion 20Hz with FIR filtering > 80dB
Rate
Operating Temperature: –10 to +50°C ambient
Environment Humidity: 100%
Storage: –20 to +50°C ambient
IP69K
Case Materials PC+Polyester alloy, PBT, Silicon Rubber, SS304 Stand
Packing Weights Basic Indicator: 2.0kg
Digital
Display LED Backlit LCD with six 20mm high digits with units and
annunciators
Setup and Full digital with visual prompting in plain messages
Calibration
Digital Filter Sliding window average from 0.1 to 4.0 seconds
Zero Range Adjustable from 2% to 100% of full capacity
Power Input
Standard Power 12 to 24VDC, 9.6, 12 and 24V batteries (2.5 VA max) -
Input ON/OFF key with memory feature
Variants AC AC Power supply: 110/240VAC 50/60Hz in 24VDC 1.25A
out
Battery 12V battery pack (rechargeable NiMH)
Features
opto-LINK Data Infra-red Connector for optional opto-LINK PC cable (to RS-
Coupling 232 or USB PC port)
Correction Ten point linearity correction (K304 Only)
Outputs RS-232 automatic transmit, network or printer outputs.
Transmission rate: 2400, 4800 or 9600 baud
Assignable Unit switching, counting, manual hold, peak hold, live weight,
Function Key totalising
Drive Outputs 3 isolated high side drive outputs (400mA each 12-24VDC)
Battery Backed Battery life 10 years minimum
Clock Calendar
003X-608-133 Page 3
Quick Start Manual Rev 1.33
4. Warnings
4.1. General
• Indicator not to be subject to shock, excessive vibration or
extremes of temperature (before or after installation).
• Inputs are protected against electrical interference, but
excessive levels of electro-magnetic radiation and RFI may
affect the accuracy and stability.
• For full EMC or for RFI immunity, termination of cable shields
and correct earthing of the instrument is essential.
• Indicator and load cell cable are sensitive to excessive
electrical noise. Install well away from any power or
switching circuits.
4.2. Configuration Issues
• Configuration and calibration can be performed from the front
panel, using digital setup. When Full Setup is used, all menu
items are accessible and care must be taken to ensure no
accidental changes are made to calibration and trade
settings.
• Enter a passcode to prevent unauthorised or accidental
tampering. If the passcode is lost, the manufacturer should
be contacted for further advice.
Page 4 003X-608-133
Quick Start Manual Rev 1.33
5. Installation
The following steps are required to set up the indicator.
• Inspect indicator to ensure good condition.
• Use connection diagrams to wire up load cell, power and
auxiliary cables as required.
• Connect Power to indicator and press <POWER> key to turn
the instrument On.
• Refer to the Instrument Setup section page 17 for information
on configuring and calibrating the instrument.
• To turn instrument Off press and hold <POWER> key for
three seconds (until display blanks).
003X-608-133 Page 5
Quick Start Manual Rev 1.33
5.2. opto-LINK
The optional opto-LINK cable
can be used to transfer setup
and calibration information
from a PC (eg. to be stored for
later use and/or transferred to
other instruments). It can also
be used to download software
upgrades to the instrument
from a PC.
• Attach the opto-LINK cable to the PC using the DB9 or USB
connector.
• Attach the opto-LINK head to the left side of the instrument
display using the permanent magnet located within the head of
the opto-LINK.
Page 6 003X-608-133
Quick Start Manual Rev 1.33
6. Connections
6.1. Cable Connections
• All cable connections are made to the rear of the instrument
using pluggable screw terminals.
003X-608-133 Page 7
Quick Start Manual Rev 1.33
Page 8 003X-608-133
Quick Start Manual Rev 1.33
003X-608-133 Page 9
Quick Start Manual Rev 1.33
Page 10 003X-608-133
Quick Start Manual Rev 1.33
003X-608-133 Page 11
Quick Start Manual Rev 1.33
Page 12 003X-608-133
Quick Start Manual Rev 1.33
WARNING
The remote input is a
voltage free contact (eg.
button, mechanical relay).
Connection of any active
circuitry may damage the
instrument.
6.4.5. Outputs
• The output drivers for the instrument are high side drive and
are capable of driving up to 400mA each.
• This configuration allows for the direct connection of the
instrument outputs to most types of PLC.
• The voltage applied to the instrument’s positive power supply
terminal (+) appears on the output lines when the outputs are
active.
• To drive external loads (eg. relays), connect the output line
directly to the positive side of the relay coil. Connect the
negative side of the relay coil to COMMON.
• It is recommended that fly-back diodes or transient
suppressors be fitted across inductive loads such as relay
coils to limit switching noise.
003X-608-133 Page 13
Quick Start Manual Rev 1.33
Page 14 003X-608-133
Quick Start Manual Rev 1.33
003X-608-133 Page 15
Quick Start Manual Rev 1.33
6.6.1. Sealing
Page 16 003X-608-133
Quick Start Manual Rev 1.33
7. Instrument Setup
7.1. Calibration Counter
The built-in calibration counter(s) monitor the number of times
trade critical settings are altered. Refer to Trade Critical
Settings below for more information and to the OPTION:USE
setting page19.
The table below describes when the counter(s) will increment.
Industrial, NSC or OIML: The Calibration Counter
increments when trade critical settings are changed. An
example of the counter is C.00019.
NTEP: Two counters display.
The Calibration Counter increments when trade critical
settings in the Calibration (CAL) menu are changed. An
example of the counter is C.00010.
The Configuration Counter increments when other trade
critical settings (ie. not in the CAL menu) are changed. An
example of the counter is F.00009.
003X-608-133 Page 17
Quick Start Manual Rev 1.33
Page 18 003X-608-133
Quick Start Manual Rev 1.31
GROUP ITEM SELECT EDIT OK
(GRP) (ITM) (SEL) (EDT)
Underline = Defaults
BUILD DP⊗ Decimal Point Position 000000, 00000.0, 0000.00, 000.000, 00.0000, 0.00000 Accept
CAP⊗ Maximum Capacity 000100 to 999999 Default = 003000 Accept
<SEL> changes position, <EDT> changes digit.
RES⊗ Resolution (Count-By) 1, 2, 5, 10, 20, 50, 100 Accept
GRADS⊗ Graduations 000100 to 030000 Default = 003000 Accept
(K306 only) <SEL> changes position, <EDT> changes digit.
UNITS⊗ Weighed Units none, g, kg, lb, t Accept
HI.RES⊗ Resolution x 10 Mode OFF, ON Accept
CABLE⊗ 4-Wire or 6-Wire 4, 6 Accept
OPTION USE⊗ Scale Use INDUST, NSC, OIML, NTEP Accept
FILTER Reading Average none, 0.2, 0.5, 1.0, 2.0, 3.0, 4.0 Accept
(time in seconds)
MOTION⊗ Motion Detection OFF, 0.5-1.0, 1.0-1.0 Accept
Default = 0.5 Graduations per Second
INIT.Z Initial Zero on Startup OFF, ON Accept
Z.TRAC⊗ Zero Tracking Sensitivity OFF, SLOW (0.5 grads/sec), FAST (10 grads/sec) Accept
Z.RANGE⊗ Zero Operating Range -2_ 2, -1_ 3, -20_20, FULL Accept
Default = -2_ 2 (–2% to +2%)
003X-608-133 Page 19
Quick Start Manual Rev 1.33
GROUP ITEM SELECT EDIT OK
(GRP) (ITM) (SEL) (EDT)
Underline = Defaults
OPTION Z.BAND⊗ Zero 'Dead' Band <SEL> changes position, <EDT> changes digit. Accept
(ctd) Default = 0
R.ENTRY⊗ Enable Rear Pushbutton OFF, ON Accept
for Full Setup Entry
CAL ZERO⊗ Zero Calibration Routine <SEL> key to start. Current weight displays.
Set between zero and full Remove all weight.
scale <SEL>, <EDT> or <OK> starts routine (Z.in P displays).
(Current weight displays) <ITM> key to exit, <SEL>, <EDT> or <OK> to repeat routine.
SPAN⊗ Span Calibration Routine <SEL> key to start <EDT> key to select clear linearisation
Set between zero and full points ( CLr.L y displays). or not ( CLr.L n displays).
scale <OK> key to select alternative.
(Current weight displays) Current weight displays.
Add test weight.
<SEL> or <OK> to show calibration weight value.
Set correct weight. <SEL> changes position, <EDT> changes
digit.
<ITM> or <OK> starts routine (S.in P displays).
<ITM> key to exit, <SEL>, <EDT> or <OK> to re-edit
calibration weight and repeat routine.
Page 20 003X-608-133
Quick Start Manual Rev 1.31
GROUP ITEM SELECT EDIT OK
(GRP) (ITM) (SEL) (EDT)
Underline = Defaults
CAL ED.LIN⊗ Edit Linearisation Points <SEL> to step through list of points.
(ctd) (K304 only) Set between zero and full <OK> to change selected point or <ITM> to exit.
scale After <OK> current weight displays.
L1. - - - Select Linearisation Add test weight.
point 1 to 10 (L1, L2, L3, L4, <OK> to enter corrected weight. <SEL> changes position,
L5, L6, L7, L8, L9, L10). <EDT> changes digit.
(Approx. % of full scale) <OK> starts routine (L.in P displays).
<ITM> key to exit, <OK> to repeat routine.
CLR.LIN⊗ Clear Linearisation <SEL> to step through list of points.
(K304 only) Points <OK> to select point to clear or <ITM> to exit.
L1. - - - Select Linearisation After <OK> press <ITM> to choose Cont. Y (Yes) or Cont. N
point 1 to 10 (L1, L2, L3, L4, (No).
L5, L6, L7, L8, L9, L10) <ITM> to return to CLR.LIN.
DIR.ZER⊗ Direct Zero Calibration <OK> key to start. Current weight displays.
(Current weight displays) <OK> to enter direct zero setting (in mV/V).
<SEL> changes position, <EDT> changes digit.
<OK> key to store new zero calibration.
<ITM> to exit or <OK> to repeat operation.
003X-608-133 Page 21
Quick Start Manual Rev 1.33
GROUP ITEM SELECT EDIT OK
(GRP) (ITM) (SEL) (EDT)
Underline = Defaults
CAL DIR.SPN⊗ Direct Span Calibration <OK> key to start. Current weight displays.
(ctd) (Current weight displays) <OK> to enter direct span setting (in mV/V).
<SEL> changes position, <EDT> changes digit.
<OK> key to store new span calibration.
<ITM> to exit or <OK> to repeat operation.
G.INST⊗ Installation Gravity 9.750 to 9.860 Default = 9.810 Accept
(K306 only) (Current setting displays) Gravity Compensation Only
G.FAC⊗ Factory Gravity 9.750 to 9.860 Default = 9.810 Accept
(K306 only) (Current setting displays) Gravity Compensation Only
G.FIRST⊗ First Powerup Prompt ON, OFF Accept
(K306 only) (Current setting displays) Prompts user to enter G.INST on first powerup
FAC.CAL⊗ Factory Calibration Cont. N Accept
Cont. N (No) Warning: Choosing Cont. Y will restore default factory
Cont. Y (Yes) calibration in BUILD and CAL menus.
Page 22 003X-608-133
Quick Start Manual Rev 1.31
Underline = Defaults
SPEC SAFE.PC Safe Setup Passcode (000000 no passcode). Set up to 6 digit passcode. Accept
<SEL> changes position, <EDT> changes digit.
Activated only when FULL.PC is also set.
FULL.PC Full Setup Passcode (000000 no passcode). Set up to 6 digit passcode. Accept
<SEL> changes position, <EDT> changes digit.
KEY.LOC Front Panel Key Locking P12345 Accept
P12345 Character indicates key is unlocked.
(P for Power key. (–) Dash indicates key is locked.
Other keys numbered from <SEL> changes position, <EDT> changes digit.
the left, ie. Zero=1.)
KEY.FN <FUNCTION> Key NONE, TEST, COUNT, UNITS, HOLD, PEAK.H, LIVE.WT, Accept
Setting SHOW.T, HI.RES, A.TARE, CHECK.W
AUT.OFF Auto Power Off / Battery NEVER, 1, 5, 10 (time in minutes) Accept
Operation Default = Never powers off automatically
(Battery Mode: powers down after 30 minutes)
B.LIGHT Backlight Operation ON, OFF, FORCED Accept
(Battery: Automatically turns backlight off after 10 seconds of
inactivity)
REM.FN Remote Function NONE, KEY1 to KEY5, BLANK Accept
(Activated only when SERIAL:TYPE is set to AUTO, PRINT or
AUTO.PR)
003X-608-133 Page 23
Quick Start Manual Rev 1.33
GROUP ITEM SELECT EDIT OK
(GRP) (ITM) (SEL) (EDT)
Underline = Defaults
SPEC REM.CHR Remote Input Transmit Idle 000 to 255 Default = 005 Accept
(ctd) Character <SEL> changes position, <EDT> changes digit.
BAT.VLT Battery Voltage PWR, 9.6, 12, 24 Accept
W.D.LOCK Wash Down Key Lock OFF, ON Accept
(On requires correct sequence of keys pressed on startup)
SERIAL TYPE Serial Output Type NET, AUTO, SINGLE, PRINT, AUTO.PR Accept
FORMAT Serial Output Format MASTER, CUSTOM, FMT_1, FMT_2, Accept
BAUD Serial Baud Rate 2400, 4800, 9600 Accept
BITS Serial Format Options N 8 1 - (Default Serial Format Options) Accept
Position 1: Parity <SEL> changes position, <EDT> changes digit.
Position 2: Data Bits Parity: N None, O Odd, E Even
Position 3: Stop Bits Data Bits: 7 or 8 data bits
Position 4: DTR Handshake Stop Bits: 1 or 2 stop bits
DTR: (-) DTR disabled or d DTR enabled
ADDRES Instrument Address 01 to 31 Accept
<SEL> changes position, <EDT> changes digit.
SERIAL RST.CON⊗ Reset Printed Consecutive Cont. N Accept
(ctd) Numbers to 1 <ITM> to choose Cont. Y (Yes) or Cont. N (No)
Cont. N (No)
Cont. Y (Yes)
Page 24 003X-608-133
Quick Start Manual Rev 1.31
Underline = Defaults
CHECK.W ENABLE Enable Check Weighing OFF, ON Accept
SRC Weight Source GROSS, DISP, NET (Displayed) Accept
OVER Target for Over Weight -99999 to 999999 Default = 000000 Accept
UNDER Target for Under Weight -99999 to 999999 Default = 000000 Accept
CLOC FORMAT Date Format Setting dd.mm.yy or mm.dd.yy Accept
(K307: mm.dd.yy or dd.mm.yy)
YEAR Year Setting 2000 to 2099 Accept
<SEL> changes position, <EDT> changes digit.
MONTH Month Setting 01 to 12 Accept
<SEL> changes position, <EDT> changes digit.
DAY Day Setting 01 to 31 Accept
<SEL> changes position, <EDT> changes digit.
HOUR Hour Setting 00 to 23 Accept
<SEL> changes position, <EDT> changes digit.
MINUTE Minute Setting 00 to 59 Accept
<SEL> changes position, <EDT> changes digit.
003X-608-133 Page 25
Quick Start Manual Rev 1.33
GROUP ITEM SELECT EDIT OK
(GRP) (ITM) (SEL) (EDT)
Underline = Defaults
TEST SCALE Scale Base Test Display Display reads in millivolts-per-volt
(factory calibrated to 0.1%)
Verify the correct load cell capacity and/or load cell wiring is
used. Remove weight from scale.
FRC.OUT Force Outputs <EDT> advances through outputs
(ie. ON.1 and ON.2)
<OK> turns outputs off and exits test.
Default = OFF
O.LOAD Input Overload Count Displays the number of occurrences of an input overload. Return
CLR.OLD Clear Overload Count Cont. N Accept
Cont. N (No) Choosing Cont. Y will clear the overload count.
Cont. Y (Yes)
FACTRY DEFLT Restore Factory Defaults Cont. N Accept
Cont. N (No) Warning: Choosing Cont. Y will clear all stored data except
Cont. Y (Yes) BUILD and CAL menus.
- END - EXIT SETUP Save settings and return Accept
to normal weighing
mode
Page 26 003X-608-133
Quick Start Manual Rev 1.33
8. Error Messages
8.1. Weighing Errors
• Check Setup = This item can be checked on site by service
personnel
Error Description Resolution
(U - - - - -) The weight is below the Increase the weight or
minimum allowable weight decrease the minimum
reading. allowable weight
reading.
(O - - - - -) The weight is above the Check the condition of
maximum allowable weight load cell connections.
reading. Check for damaged load
Warning - overloading cell.
may damage mechanical
scale elements.
(ZERO) The weight reading is Increase the Zero Range
(ERROR) beyond the limit set for (Z.RANGE) or use the
Zero operation. The <TARE> key instead.
operation of the <ZERO>
key is limited in the setup
during installation. The
indicator cannot be Zeroed
at this weight.
(STABLE) Scale motion has Try the operation again
(ERROR) prevented a <ZERO>, once the scale is stable.
<TARE> or <PRINT>
operation from occurring
on command.
003X-608-133 Page 27
Quick Start Manual Rev 1.33
Page 28 003X-608-133
Quick Start Manual Rev 1.33
003X-608-133 Page 29
Quick Start Manual Rev 1.33
Notes:
Page 30 003X-608-133
Notes: