SET110 220-5KLC Pure Sine-Wave Inverter

Users Manual
 Table of Contents

I、 SET110 220-5KLC Model Notes……………………………………………4

II、 SET110 220-5KLC Functions ……………………………………………4

III、 SET110 220-5KLC Technical Specifications ………………….……………6

IV、 SET110 220-5KLC Operation Method …………… …. ……….………7

V、 SET110 220-5KLC Maintenance Information………………………………7

VI、 SET110 220-5KLC Mechanical Information ………………….………9

VII、 Warranty letter ………………………………………………….………10

Page2 of 10
 IMPORTANT SAFETY NOTES

 Please keep this manual for future use.

 Please read this manual carefully at the first time when install, operation and maintain
according to the manual instructions.
 AC input voltage of the series is 220V/50Hz, DC input voltage of the series is 110VDC;
please connect as per the instructions to avoid the possible damage.
 Please turn off the inverter and disconnected all cables before moving.
 To avoid the damage and hurt to people and inverter, please don’t open cover by
yourself.
 Do not use it with overload which can affect inverter life.
 Please put the inverter in the dry place, at least 10cm away from the wall.
 Protecting from direct sunlight, rain and moisture.
 Please put it far away from fire and high temperature.
 Please do not put things on the top of inverter.
 Please contact dealer or manufacturer service center for any problem, do not open the
cover to avoid any further damage and risk.

Warning：
The product can be affected by the radio under certain circumstances,
further protection equipment is needed.

Page3 of 10
I. SET110 220-5KLC Model Notes:
SET 110/220-5K LC

C…………LCD display
L………..19 Inch Rack Type

5K……….Power (VA)

220……..AC Output Voltage

110……….DC Input Voltage

SET

II. SET110 220-5KLC Functions

With the development of information and network technology, the new generation DC-AC
power supply, sine-wave inverter, are widely used in telecom, mobile, air field, banking, office,
industry, hospitals, military and research fields. By using battery as DC input, and sine-wave
AC output after inverter, the output voltage and frequency of Sine-wave inverter are very
steady and can work continuously, avoiding the problems of power break, voltage unsteady,
noise and lightning invasion. With the sine-wave inverter can guarantee the utility and
equipment reliable work and system safety.

Sine-wave Inverter is a kind of DC-AC power supply, the output wave is pure sine-wave by
SPWM technology, with the features of fast reaction, low wave distortion, output voltage and
frequency steady. This inverter is also equipped with the protections of over DC input, low
voltage, over AC output, overload, circuit shortage and internal over heat, these can guarantee
good performance, working reliability and other technical specifications.

Sine-Wave inverter is designed based on center control system to meet the power supply
requirements of computer and other terminals, mainly applying for:
 Various managing equipment of digital communication system, including terminal,
monitor and cashier equipment.
 Server, intelligent platform of information network system, power system and instrument.
 Suitable for system which has only DC power and don’t have AC power system.

Page4 of 10
Features of Inverter:

a) With micro-CPU control, SET110 220-5KLC inverter is an intelligence model

product, good designing and reliability are the advantages.
b) SET110 220-5KLC inverter is adopting SPWM technology, with the output of
stabilized voltage and frequency, pure sine-wave.
c) SET110 220-5KLC inverter has good compatibility, built-in by-pass switch,
high overload feature for reliable and continuous power supply.
d) SET110 220-5KLC inverter is DC power type. The inverter power supply is
main when the city power is normal, when inverter power is off, city power
comes into work state automatically.
e) With the excellent designing, SET110 220-5KLC inverter can be auto switched
to bypass on the running state, it’s easy to maintain and replace the battery
without effecting load power supply.
f) In case there is battery voltage high/low or overload, the overload warning
shutdown output, when battery voltage recovers normal, battery voltage recovers;
power supply output will auto recovers in 50 seconds after overload off. This
function is very suitable for the communication station in which there is no
person on duty.
g) SET110 220-5KLC inverter can support network communication system; power
working state can be monitored by the supervision software.
h) SET110 220-5KLC inverter provides with two dry connectors which can be
used for DC input fault checking and AC output problem warning.

AC Output

Figure1：Inverter Function Diagram

Page5 of 10
III. SET110 220-5KLC Technical Specifications
Chart1：SET110 220-5KLC Technical Specifications
Output power 5KVA
Run mode Pure inverter/online interactive
Rated input voltage 110V
Rated input current 46A

DC Input Turn-off voltage range 93.4V-143V

Turn-on voltage range 107.6V-136.3V
Anti-noise current irrigation ≤10%
Bypass voltage(V) 260V-180V(±10V)
AC Input Rated input current（A）
Bypass transfer time（ms） ≤5ms

Rated capacity 5000VA

Rated output power 3500W
Rated output voltage and frequency 220Vac，50Hz

Wave shape Pure sine wave

Rated output current 16A
Output voltage accuracy 220 V±1.5%
AC Output
Output frequency accuracy 50Hz±0.1%

Waveform distortion ≤3%

Dynamic Response Time 5%

Power factor 0.8
Overload 120%，30s
Efficiency（80% Resistive load） ≥85%

Dielectric Strength Input & output 1500Vac，1min

Noise（1m） ≤40dB

Work Ambient temperature -25℃~+50℃

environment Humidity 0~90%，Non-condensing
Altitude（m） ≤1000
Cooling Forced air

HMI LCD display

Interface
Communication interface RS232
communication
stem load output 3ch output
interface
SNMP Optional
Input undervoltage, overvoltage; output overload, short circuit
Protection
protection; AC input high and low voltage protection
Output wiring Terminal Blocks

Weight 16KG
Dimension 500（W）×605（H）×170（D）mm

Page6 of 10
IV. SET110 220-5KLC Operation Method
 Installation
1. Open the package and check accessories ( 8pc output terminals and 1 Manual )
2. Choose a clean and ventilation area.
3. Make sure DC voltage and battery voltage are inverter required.
4. Check the power Positive and Negative line.
5. Connecting Positive Cable with the terminal DC48V“+” on the back panel，and negative Cable
with the “-”.
6. Connecting AC input L/N/G with AC Input terminals L/N/G.( AC Ground must be connected into
ground area )
7. Connecting load cables with AC output terminals L/N/G.
 Start
a) Make sure that input DC and AC output cables are right connected.
b) Turn on DC input switch.
c) Put the start switch on“I”，inverter comes into the state of self-inspection, showing inverter is on.

Notes: Self-inspection------Before the output is delivered, the inverter will check the related parts and system
state. When the all meters of inverter is in normal, the inverter will be in working status of power supply and
inversion. This checking takes about 10 seconds, indication LED lights from left to right two times during
this period.
 Shutdown
Put the start switch on“O”，all LED light and becomes dark, inverter is shutdown.

V. SET110 220-5KLC Maintenance Information

 Figures

ON/OFF button-- （SWITCH）

Beeper ON/OFF-- （BUZ）

“Bypss output”LED，green； ENTER

“Inverter”LED，blue； UP

“Battery Fault”LED，red； DOWN

“Load fault”LED，red； BUZ

Page7 of 10
Chart2： LED Lights and Indication

Status Out Power Inver. Battery Load

Output
Item Type Green Blue Red Red
Inversi
1 Self Test Yes on or On→ →On→ →On→ →On→
Power
Yes Yes
2 Battery Fault Dark On Blink Dark
No No
3 Power Normal Yes Power Light Dark Dark Dark
Inversi
4 Power to Inversion Yes Dark Light Dark Dark
on
Yes( Lower Power/
5 DC Voltage Low than start Inversi Dark Blink Dark Dark
voltage) on
DC Start Voltage
6 No No Dark Dark Dark Dark
Low
DC input voltage Yes Yes
7 Blink Dark Dark Blink
High No No
Inversion Output Yes Yes
8 Dark Blink Blink Dark
Fault No No
9 Overload Shutdown No No Dark Dark Blink Light
10 Shortage Shutdown No No Light Light Blink Light
Inversion Wave Yes Yes
11 Blink Blink Blink Dark
Fault No No
12 DC 0ff Yes Yes Light Dark Dark Dark
Notes：“→”shows that the LED lights in order,“×”shows no light.
1） For protecting battery, inverter can only start when battery voltage in within the Starting
Voltage .After entering into working state, inverter can work normally as the battery voltage is
within Working Voltage .
2）When battery voltage reduced to Starting Voltage there is a voltage warning, when the voltage goes
lower than Working Voltage inverter will shutdown.

Page8 of 10
VI. SET110 220-5KLC Mechanical Information

Figure 1：1KVA-5KVA Mechanical info(2U/19 Inch Rack Type LCD Panel）

Machine Model:
1KVA Size: 482*375*88 (W*D*H) Weight: 8Kg
2KVA Size: 482*375*88 (W*D*H) Weight: 8Kg
3KVA Size: 482*375*88 (W*D*H) Weight: 10Kg
4KVA Size: 482*375*88 (W*D*H) Weight: 12Kg
5KVA Size: 482*375*88 (W*D*H) Weight: 15Kg

Warranty Letter
We warrant that this product is free from defects in material and workmanship and agree to remedy any
defect (or at its option replace the product) for a period of one year from the date of purchase. Parts may be
replaced under this warranty with new or remanufactured parts.

This warranty will not apply to any product that has been improperly installed (as described in the
installation manual), misused, abused, used in ways the product was not designed, altered or repaired in any
way which may affect the performance or reliability of operation, sustained damage by power surges or
electrical storms, or sustained shipping damage, or repaired by any unauthorised repair centre.

We make no other warranties, express or implied, including any warranty of fitness for a particular purpose.
In no event shall be responsible for indirect or consequential damages or lost profits even if we have been
advised of the possibility of such damages. Our sole obligation to you shall be the repair or replacement of a
non-conforming product.

Page9 of 10
 User’s Information
User Company: Contact person:

Address: Phone:

Dealer company: Post code:

Model: Serial number:

Purchase date: Handling person:

Repair Record
Date Record Abstract Technician Signature

Page10 of 10