Three-Phase Transformers

See discussions, stats, and author profiles for this publication at: https://www.researchgate.
net/publication/337932682
Chapter 5. Three-Phase Transformers
Presentation · December 2019
CITATIONS READS
0 3,676
1 author:
Francisco Gonzalez-Longatt
Loughborough University
504 PUBLICATIONS 4,484 CITATIONS
SEE PROFILE
All content following this page was uploaded by Francisco Gonzalez-Longatt on 14 December 2019.
The user has requested enhancement of the downloaded file.

Dr. Francisco M. Gonzalez-Longatt
Dr F Gonzalez-Longatt
Three-Phase
Transformers
1/33
All rights reserved. No part of this publication may be reproduced or distributed in any form without permission of the author. Copyright © 2008-2019. http:www.fglongatt.org
Objective
This chapter presents a general summary of three-phase
transformers and its practical aspects related to the
operation in AC steady-state systems.
Dr. Francisco M. Gonzalez-Longatt 2/33

Introduction
3/33
Introduction
• A power transformer is defined as:
• "A power transformer a static piece of apparatus with two

or more windings which, by electromagnetic induction,
transforms a system of alternating voltage and current into
another system of voltage and current usually of different
values and at the same frequency for the purpose of
transmitting electrical power.“
• BS EN 60076-1:2011, Power transformers, Part 1: General.

Sub-section 3.1.1 of Terms and definitions General.

Introduction
• In the UK high-voltage, long-distance transmission systems
operate at 275 kV and 400 kV;
• Distribution systems operate most commonly at 132 kV, 66 kV

and 33 kV, with local systems operating at 11 kV down to
415 V.
• All of these systems have three-phases.
• Transmission and distribution systems operate at high voltages

in order to reduce loses and improve efficiency.
• However, it is clear that for such systems to work three-phase

transformers are required to link sections operating at different
voltages.
basics
Three-phase transformer
6/33
Three-phase transformer basics
• The primary windings of three identical single-phase
transformers are connected to a 3-phase supply, and each
winding is connected between a pair of lines. That situation
is depicted in Fig. 5.1(a).
a1 c1
a2 b1
b2 c2
1 2 3
a1
a2
(a) Single-phase transformers connected to a three-phase supply: three-phase transformer bank.

Fig. 5.1. Three-phase transformer arrangements: (a) bank and (b) unit. Magnetic flux directions
are shown.
• Under normal balanced conditions, the three voltages, and
consequently the three fluxes, are mutually displaced by
120, so that 1 +  2 +  3 = 0
• If the three transformers are placed side-by-side, with a
common yoke top and bottom, there is no need to provide a
return path for the flux. This arrangement, shown in Fig.
5.1(b), is the very common 3-limb construction.
(b) Three-limb transformer:
1  2  3 Three-phase transformer unit.
a1 b1 c1
a2 b2 c2
Fig. 5.1. Three-phase transformer
arrangements: (a) bank and (b) unit.
Magnetic flux directions are shown.
• In Fig. 5.2(b), the lengths of the magnetic paths for the
three phases are not quite equal, and the magnetising
currents are consequently not balanced, with the centre
phase being lower.
• Very large transformers use the five-limb construction of
Fig. 5.2., which has windings only on the centre three
limbs.
1  2  3
(b) Three-limb transformer:
Three-phase transformer unit.
a1 b1 c1
a2 b2 c2
Fig. 5.1. Three-phase transformer
arrangements: (a) bank and (b) unit.
Magnetic flux directions are shown.
• Five limb transformers have balanced phases, but because
the yokes and outer limbs carry only half the flux of the
centre limbs their size can be reduced.
• The reduction in height can ease transportation difficulties.
1 1 1 1 1 1
1 1  2  2 3 3
2 2 2 2 2 2
These heights are

reduced because
1 2 3 the yoke flux is
reduced
Fig. 5.2. Illustrative example of a 3-phase 5-limb transformer core. Magnetic flux directions
are shown.

• A 3-phase transformer bank costs less, weighs less,
requires less floor space and has a slightly higher
efficiency than three single-phase transformers of the same
total rating.
• The VA rating of each phase (or each transformer of a

group of three single-phase transformers) is one-third of
the total VA rating of the bank, regardless of the
connection or core type used.
• The voltage and current ratings of the individual phases or

transformers depend on the connection used.

Three-phase connections
12/33
13/33
14/33
• The star-delta connection is common in stepping down from
a high to a medium or low voltage, since an earthed neutral may
then be provided on the HV side.
• Similarly, a delta-star connection is common when a voltage
is stepped up to a high voltage. Delta-star is also used in
distribution systems where a neutral point is required for single-
phase loads.
• In a delta-delta connection, one transformer may be
removed for repair or maintenance, and the supply may be
maintained. The arrangement of the two remaining
transformers is called an open-delta connection.
• The star-star connection is seldom used, because of the
problems involved in harmonic reduction.
• In rectifier circuit applications secondary phase windings are
sometimes inter-connected to produce a 6-phase output or to
improve load distribution between phases.
Transformer groups
16/33
Transformer groups
• A large number of possible transformer connections are
specified in standards, where they are arranged in groups
that have the same primary to secondary phase
displacement.
• The most common groups, listed in Table 5.2, are:
• Group 1: Zero phase displacement (Yy0, Dd0, Dz0).
• Group 2: 180° phase displacement (Yy6, Dd6, Dz6).
• Group 3: 30° lagging phase displacement (Dy1, Yd1,
Yz1).
• Group 4: 30° leading phase displacement (Dy11, Yd11,
Yz11).
• The groups are derived from BS EN 60076-1:2011, Power
transformers, Part 1: General. Annex D.
Transformer groups
• Connections are designated by letters; Y or y for star, D or
d for delta and Z or z for zig-zag, upper case is used for the
high voltage (HV) windings and lower case for the low
voltage (LV) windings.
Vab VAB
30°
A a
+ + Van
VCA -
+ Van Vab -Vbn
+ -
C VAB n - Vbn
- - + -
-
VBC + Vcn b
+ Vcn Vbn
B c
VCA VBC
Group 4: +30° (Dy11)
Fig. 5.3. Delta-star 3-phase transformer: Group 4: Dy11.

3-phase transformer groups
A2 a2 A2 b1 c1
Yy0 Yy6 n
N n N
C2 B2 c2 b2 C2 B2 a1
A2 a2 A2 b c1
b1
Dd0 C A c a Dd6 C A
a c
C2 B B2 c2 b b2 C2 B B2 a1
A2 a4 A2 c3
b3
a b a b c
Dz0 C A Dz6 C A c n
b c
c n a b a
C2 B B2 c4 b4 C2 a3
B B2
Group 1 (0°) Group 2 (180°)

A2 a2 Dy11 A2 a2
Dy1 A B C A n b2
c2 n
C2 B2
C2 C B2 b2 B c2
A2 a2 A2 a2
c b
Yd1 Yd11 a
N c2 a N b2
C2 B2 b C2 B2 c
b2 c2
A2 a4 A2 a4
a
Yz1 c b
a Yz11 b b
N c N c b4
c4 n n
a a
C2 B2 b C2 B2
b4 c4 c
Group 3 (-30°) Group 4 (+30°)

Equivalent circuits
20/33
Equivalent circuits
• Three-phase transformers are usually represented by the
conventional (approximate) single-phase equivalent circuit
Fig. 5.4, with the phases, assumed to be the same.
VP 1 Ip1 jX1
Ip1 R1 X1 I P2 IP 2 Ip1 R1
+ IP0 + V
+ P2
+ Z1 Ip1
VP 1 rm xm V P2 VP 2
EP1 f2 I P2
- IP 0a - IP 0r - - f1
N1:N2
Ideal IP0
Transformer
Fig. 5.5. Approximate phase equivalent circuit (left) and phasor diagram (right).
Equivalent circuits
• The primary circuit phase resistance R1, which is equivalent to the
primary and referred secondary phase resistances.
• The primary circuit phase reactance X1, which is equivalent to the
primary and referred secondary phase leakage reactances.
• The core loss resistance rm taking an active current IP0a, such that
is one-third of the total core loss. I P 0a 2rm
• The magnetizing reactance xm taking a reactive current IP0r which is
the magnetizing current per phase.
Ip1 R1 X1 I P2 IP 2
+ IP0 +
+
+ Z1
VP 1 rm xm V P2 VP 2
EP1
- IP 0a - IP 0r - -
N1:N2
Ideal
Transformer
Equivalent circuits
• An ideal transformer of turns ratio N1:N2 having the following
characteristics:
• The core material has infinite relatively permeability, i.e. it
has zero reluctance.
• The core material exhibits no hysteresis (and therefore no

hysteresis loss).
• The core material is non-conductive, i.e. it has infinite

resistivity (and therefore no eddy current loss).
• All flux set up by one winding links the other, i.e. mutual
coupling is perfect.
• The windings have zero resistance (and therefore no

resistive losses).
Rating and performance
24/33
Rated Power
• The nominal rated power of a transformer is a
conventional value of apparent power (in VA, kVA or
MVA) which the transformer can safely supply under the
manufacturer's specified conditions, i.e. the rating specifies
the output.
• It establishes the rated secondary winding current and
implies the rated primary winding current.
• The rated power has an almost exclusively thermal basis,
the limitation being the maximum working temperature
for which the insulation will have a reasonable economic
life.
S1 = 3VL1 I L1  S2 = 3VL 2 I L 2
S1 = 3VP1 I P1  S2 = 3VP 2 I P 2
Voltage regulation (VR)
• Voltage regulation (VR) is the change in the secondary
voltage between no-load and full-load with the primary
voltage assumed constant.
• It can be expressed directly as a voltage:
Voltage regulation (VR) = no-load voltage – full-load voltage
• but is usually expressed as a fraction of the no-load voltage,
either per-unit or per-cent.
no-load voltage − full-load voltage
Voltage regulation (VR ) % = 100%
no-load voltage
• which can be calculated with the line or phase voltages, or

I P 2
Voltage regulation (VR ) %  ( R1 cos f2  X1 sin f2 ) 100%
VP1

Efficiency ()
• Efficiency () is the ratio of output power and input power.
• It can be expressed either in per-unit or percentage terms.
output power
efficiency,  % = 100%
input power
output power
efficiency,  % = 100%
output power + losses

Power Losses
• The losses in a transformer have two main components:
• Hysteresis and eddy current losses in the core and
• Resistive losses in the windings

Hysteresis and eddy current losses in the core (Pi)
• Core losses are reasonably constant since they vary with
flux and the flux varies by only a few per cent between no-
load and full-load.
• These losses are usually called iron losses (Pi)

Resistive losses in the windings (Pc)
• Total resistive losses (Pc) vary with load since they are
related to the square of the winding currents. These losses
are usually called copper losses.
• So that the efficiency () is defined as:
3VP 2 I P 2 cos (f2 )
= 100%
or 3VP 2 I P 2 cos (f2 ) + Pi + Pc
3VL 2 I L 2 cos (f2 )
= 100%
3VL 2 I L 2 cos (f2 ) + Pi + Pc
• Iron losses (Pi) are represented in the equivalent circuit by
the power dissipated in the shunt phase resistances rm, so
that
( VP1 )
2
Pi = 3  (Watt)
rm
• Copper losses (Pc) are represented in the equivalent circuit
by the power dissipated in the series phase resistances R1,
so that
Pc = 3  ( I P 2 ) R1 (Watt)
2
• The full-load output power = S cos (f2), where S is the

product of the rated secondary voltage and current, i.e. the
apparent power, so that at n times full-load:
n  S cos f2
 fl = 100%
n  S cos f2 + Pi + n2  Pc

• Maximum efficiency ( = 1.0 = 100%) occurs when the
iron loss (Pi) and copper loss (Pc) are equal:
Pi  Pc
• Maximum efficiency occurs therefore at the fraction n of
full load where:
Pi = n2  Pc
• And
n = Pi Pc
• Note: All of the equations in this section are valid for
balanced conditions only, under other conditions individual
phase components of voltage, current and losses must be
considered.

Dr. FranciscoViewM.
publication stats
Gonzalez-Longatt
Dr. F Gonzalez-Longatt
Three-Phase
Transformers
Questions and answers
33/33

Three-Phase Transformers

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Three-Phase Transformers

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Three-Phase Transformers

Uploaded by

Copyright:

Available Formats

See discussions, stats, and author profiles for this publication at: https://www.researchgate.

Chapter 5. Three-Phase Transformers

Presentation · December 2019

The user has requested enhancement of the downloaded file.

Dr. Francisco M. Gonzalez-Longatt 2/33

• "A power transformer a static piece of apparatus with two

• BS EN 60076-1:2011, Power transformers, Part 1: General.

Dr. Francisco M. Gonzalez-Longatt 4/33

• Distribution systems operate most commonly at 132 kV, 66 kV

• All of these systems have three-phases.

• Transmission and distribution systems operate at high voltages

• However, it is clear that for such systems to work three-phase

(a) Single-phase transformers connected to a three-phase supply: three-phase transformer bank.

These heights are

Dr. Francisco M. Gonzalez-Longatt 10/33

• The VA rating of each phase (or each transformer of a

• The voltage and current ratings of the individual phases or

Dr. Francisco M. Gonzalez-Longatt 11/33

Dr. Francisco M. Gonzalez-Longatt 18/33

Group 1 (0°) Group 2 (180°)

Group 3 (-30°) Group 4 (+30°)

• The core material exhibits no hysteresis (and therefore no

• The core material is non-conductive, i.e. it has infinite

• The windings have zero resistance (and therefore no

• which can be calculated with the line or phase voltages, or

Dr. Francisco M. Gonzalez-Longatt 26/33

Dr. Francisco M. Gonzalez-Longatt 27/33

• Hysteresis and eddy current losses in the core and

• Resistive losses in the windings

Dr. Francisco M. Gonzalez-Longatt 28/33

• These losses are usually called iron losses (Pi)

Dr. Francisco M. Gonzalez-Longatt 29/33

• The full-load output power = S cos (f2), where S is the

Dr. Francisco M. Gonzalez-Longatt 31/33

Dr. Francisco M. Gonzalez-Longatt 32/33

You might also like