Wireless-Tag Technology Co.
, Limited
Smart Panlee
Smart Serial LCD Display
WT32-SC01 Plus
WT32-SC01 Plus Datasheet
Revision History:
Date Modified by Description
August 1, 2022 First release
Added firmware burning and GUI development
September 22, 2022 Hades
platform
-1-
Wireless-Tag Technology Co., Limited http://www.wireless-tag.com
WT32-SC01 Plus Datasheet
Features:
1. Support rapid prototyping
2. WT32-S3-WROVER-N16R2
Core Materials (Tab. 0):
No. Name Model Remark
1 ESP32-S3 module WT32-S3-WROVER-N16R2
-2-
Wireless-Tag Technology Co., Limited http://www.wireless-tag.com
WT32-SC01 Plus Datasheet
Hardware Interface:
Fig.1 Hardware Interface
-3-
Wireless-Tag Technology Co., Limited http://www.wireless-tag.com
WT32-SC01 Plus Datasheet
Interface Description:
[1] Debug Interface (Tab. 1)
Voltage
Pin Description Module Pin Remark
Range
1 +5V - 5V
For reference, not for
2 +3.3V - 3.3V
power input
3 ESP_TXD TXD0 3.3V TTL
4 ESP_RXD RXD0 3.3V TTL
5 EN EN 0-3.3V Chip enable
6 BOOT GPIO 0 0-3.3V
7 GND GND 0V Ground
[2] Extended IO Interface (Tab. 2)
Voltage
Pin Description Module Pin Remark
Range
Power supply or output
1 +5V - 5V±5%
voltage
2 GND - 0V Ground
3 EXT_IO1 GPIO 10 0-3.3V
4 EXT_IO2 GPIO 11 0-3.3V
5 EXT_IO3 GPIO 12 0-3.3V
Extended IO
6 EXT_IO4 GPIO 13 0-3.3V
7 EXT_IO5 GPIO 14 0-3.3V
8 EXT_IO6 GPIO 21 0-3.3V
[3] Speaker Interface (Tab.3)
Pin Description Remark
1 SPK+ Speaker positive
-4-
Wireless-Tag Technology Co., Limited http://www.wireless-tag.com
WT32-SC01 Plus Datasheet
2 SPK- Speaker negative
[4] SD Card Interface (Tab.4)
Description Module Pin Remark
SD_CS GPIO 41 SD card chip selection
SD_DI（MOSI） GPIO 40 SD card data input
SD_CLK GPIO 39 SD card clock
SD_DO（MISO） GPIO 38 SD card data output
[5] LCD Interface (Tab. 5)
Description Module Pin Remark
BL_PWM GPIO 45 Backlight control, active high
LCD_RESET GPIO 4 LCD reset, multiplexed with touch reset
LCD_RS GPIO 0 Command/Data selection
LCD_WR GPIO 47 Write clock
LCD_TE GPIO 48 Frame sync
LCD_DB0 GPIO 9
LCD_DB1 GPIO 46
LCD_DB2 GPIO 3
LCD data interface, 8bit MCU (8080)
LCD_DB3 GPIO 8
LCD_DB4 GPIO 18
LCD_DB5 GPIO 17
-5-
Wireless-Tag Technology Co., Limited http://www.wireless-tag.com
WT32-SC01 Plus Datasheet
LCD_DB6 GPIO 16
LCD_DB7 GPIO 15
TP_INT GPIO 7 Touch interrupt
TP_SDA GPIO 6 Touch IIC data
TP_SCL GPIO 5 Touch IIC clock
TP_RST GPIO 4 Touch reset, multiplexed with LCD reset
[6] RS485 Interface (Tab. 6)
Pin Description Remark
1 RS485-A RS485 bus
2 RS485-B SD card data input
3 GND Ground
4 +5V Power supply or output voltage
Hardware Peripherals:
Peripheral Name Description
Audio amplifier IIS, 2.5W @4R
LCD with touch panel
SD card SD card using SPI interface
RS485 Serial port IO with flow control
[1] Audio Amplifier (IIS interface) (Tab.7)
Description Module Pin
-6-
Wireless-Tag Technology Co., Limited http://www.wireless-tag.com
WT32-SC01 Plus Datasheet
LRCK GPIO 35
BCLK GPIO 36
DOUT GPIO 37
[2] RS485 (Tab.8)
Description Module Pin
RXD GPIO 1
RTS GPIO 2
TXD GPIO 42
[3] Electrical Parameters (Tab.9)
Parameter Test conditions Min. Typical Max. Unit
Operating
- 4.7 5.0 5.5 V
Voltage
USB provides 5V power,
Operating
with maximum backlight 170 175 190 mA
current
brightness
-7-
Wireless-Tag Technology Co., Limited http://www.wireless-tag.com
WT32-SC01 Plus Datasheet
Schematic:
-8-
Wireless-Tag Technology Co., Limited http://www.wireless-tag.com
WT32-SC01 Plus Datasheet
Specification Parameters:
[1] LCD Parameters (Tab. 10)
Display Type LCD
Driver IC Model ST7796UI
Viewing Angle FULL
Resolution 480*320
Interface MCU8080 8Bit
Color RGB565
Backlight Mode
Backlight Brightness
[2] Touch Parameters (Tab.11)
Touchscreen Type Capacitive touch
Driver IC Model FT6336U
Interface I2C
Touchscreen structure G+F
Touch Mode Single touch
Surface Hardness
Light Transmittance
-9-
Wireless-Tag Technology Co., Limited http://www.wireless-tag.com
WT32-SC01 Plus Datasheet
Outline Dimensional Drawing (Fig.2)
- 10 -
Wireless-Tag Technology Co., Limited http://www.wireless-tag.com
WT32-SC01 Plus Datasheet
Firmware Burning：
1. Connect the downloader (ZXACC-ESPDB) via a USB-Type C cable. And then connect the
WT32-SC01 Plus board with the downloader (ZXACC-ESPDB) through an MX1.25-7P cable.
As the downloader (ZXACC-ESPDB) has automatic data flow processing capabilities, the
firmware can be downloaded automatically through the ESP32 Flash Download Tools.
Fig.3
2. As shown in Fig. 4: Select the firmware path at mark 1, and then fill in the burning address,
usually 0X00. Note that this checkbox must be checked; Set the crystal frequency to be
40MHz at mark 2; Select 32Mbit for Flash size at mark 3; Select DIO for SPI MODE at mark 4;
Select the COM port number recognized by the computer at mark 5; Select the baud rate at
mark 6 (the higher the value is, the faster the firmware will be downloaded. Max.
1152000bps).
3. After the previous configuration, click START at mark 7 to start burning the firmware.
4. Complete the above steps, and then press the reset button on the back of the
development board to start running the firmware you just burned.
- 11 -
Wireless-Tag Technology Co., Limited http://www.wireless-tag.com
WT32-SC01 Plus Datasheet
Fig.4
- 12 -
Wireless-Tag Technology Co., Limited http://www.wireless-tag.com
WT32-SC01 Plus Datasheet
Online GUI Designer:
Users can use our online GUI designer platform, which is similar to MIT APP Inventor, to
realize the rapid GUI development with building blocks. Currently, the platform has
perfected the graphic interface development, and more driver code blocks will be further
improved in the future.
Login Page: http://8ms.xyz/login
User Manual: https://doc.smartpanle.cn/ESP32-S3/index.html
Fig.5
Fig.6
- 13 -
Wireless-Tag Technology Co., Limited http://www.wireless-tag.com
