HM-TRLR-D Series - EN - V1.1

HM-TRLR-D Series 100mW LoRa Transceiver ver1.
1. General
HM-TRLR-D series is a low cost, high performance transparent
transceiver with operating at 433/470/868/915 MHz. It is LoRa/FSK/
GFSK/OOK modulation variety, multi-interface mode(TTL/RS232/RS485),
high output power, high sensitivity, long transmission distance and most of
the parameters can be set via the command. Receive and send data to
automatically switch. It has a wide operating voltage and low sleep current.
It is flexible for the users to set the UART baud rate, output power, data
rate, frequency select, modulation mode select etc parameters. It is your
ideal choice for designing wireless data transmission products which can
be widely used on wireless data transmission field.
HM-TRLR-D-YYY-XXX
2. Features
l Low cost, high performance , high reliability
l LoRa/FSK/GFSK/OOK modulation, 2-way half –duplex communication, strong anti-interfere
l 433/470/868/915MHz ISM band，globally license free.
l Maximal output power100mW(20dBm)，output power adjustable between 2-20dBm
l LORA Sensitivity -139dBm
l Supply current for Tx 130mA@20dBm, 35mA@13dBm
l Supply current for Rx 20mA
l Low current sleep mode 2uA
l Wide operating voltage:3.3V-5.5V
l Standard TTL UART/RS232/RS485 interface
l Operation frequency can be configured, acceptable for several modules working in different frequency
with no disturbance on each other.
l RF parameters as needed, users can be modulated by software.
l Easily use, auto exchange on communication & transceiver
l Communication speed 1.2kbps -115.2kbps，can be modulated through software
l Afford Sleep control signal，user self control work duty cycle
l With LED indication
l Longer transmission distance，over 5Km in open air
l Small size 26*47*2mm, easy for assembly .
l Tuning free
l Accord FCC,ETSI standard
3. Application
l Remote control, remote measurement l Wireless meter
system; l Identification system
l Access control
l Data collection l IT household appliance
l Intelligence household appliance l Baby monitoring system
1
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: [email protected] http://www.hoperf.com
HM-TRLR-D Series 100mW LoRa Transceiver ver1.1
4. Pin Description
TOP VIEW
Figure 2. HM-TRLR-D Series Pin Description

Name Note
STATUS Dis-connected(when logic 1, output 3.3V voltage)
CONFIG Set low for configuration mode, while set high for communication
GND Ground
5V Power supply,3.3V-5.5V DC power
RXD TTL Data receiving
TXD TTL Data transmission
GND Ground
A_TX RS485 A (RS232 TX)
B_RX RS485 B (RS232 RX)
SLEEP Set low for normal mode for data transceiver , while back to sleep if set high
RESET Reset trigger input, Active low
5. Maximum specifiction
Parameter Min Max Unit

Power supply(VCC) -0.3 +5.5 V
Storage temperature -40 +150 ℃
Operate temperature -20 +85 ℃
Reflow temperature +260 ℃
2
6. Parameter
Parameter Condition Min Typical Max Unit

Power supply(VCC) 3.3 5.5 V
Operate temperature -20 85 ℃
HM-TRLR-D-YYY-433 414 434 454
HM-TRLR-D-YYY-470 450 470 490

Operate frequency MHz
HM-TRLR-D-YYY-868 849 869 889
HM-TRLR-D-YYY-915 895 915 935

Max output power 18 20 dBm
Output range 2 20 dBm
FSK,Fdev=35KHz,
-117
DR=1.2Kbps,
FSK,Fdev=35KHz,
-114
DR=9.6Kbps,
Receive Sensitivity LoRa SBW= 62.5KHz dBm
（FSK/LoRa） SF=12 -139
LoRa SBW= 500KHz

-130
SF=12
20dBm output
120
power
Tx Current mA
13dBm output
35
power
Rx Current 18 20 22 mA
Sleep Current TBD 8 12 uA
Modulate deviation FSK mode 10 50 KHz
Receive bandwidth FSK mode 42 166 KHz
UART Data Rate 1.2 115.2 Kbps
UART data bit 8 bit
UART stop bit 1 bit
3
7. HM-TRLR-D Series Application Circuit
Figure 3.HM-TRLR-D TTL UART Simple Application
Figure 4. HM-TRLR-D RS232 Simple application
Figure 5. HM-TRLR-D RS485 Simple application
4
Figure 6.HM-TRLR-D TTL UART Complete Application
8. Mechanical Dimension（size unit：mm）
5
9．Ordering Information
Part Number=Module type – Package type – Interface type – Operation band
Part Number Interface Operation Band

HM-TRLR-D-TTL-433 TTL 433MHZ
HM-TRLR-D-232-433 232 433MHZ
HM-TRLR-D-232-470 232 470MHZ
HM-TRLR-D-232-868 232 868MHZ
HM-TRLR-D-232-915 232 915MHZ
HM-TRLR-D-485-433 485 433MHZ
HM-TRLR-D-485-470 485 470MHZ
HM-TRLR-D-485-868 485 868MHZ
HM-TRLR-D-485-915 485 915MHZ
Table 4: Part Number list
6
（二）Operation and Applications
1. Modulation mode
HM-TRLR series transceiver module can work with the traditional FSK/GFSK modulation mode, also can
work in LoRa modulation mode. The user according to the application requirements, can easily switch in
modulation mode. Use principle need large quantities of data use FSK/GFSK modulation; The occasion of long
distance transmission is required, use LoRa modulation.
2.Work mode
HM-TRLR series transceiver module has three work modes: running mode, configuration mode and sleep mode.
When the module work in the running mode, the user can send and receive data. When the module work in
configuration mode, the user can according to his requirement, through the AT command to change configuration
parameters. Sleep mode module into low power consumption mode.
l Running mode timing scheme
Attention: During the modulation mode in LoRa receive buffer is full,the STATUS will lower the output to prompt
the user.
7
l Configuration mode scheme
Attention:When enter to the configuration mode ,through to pull down the the CONFIG ,while the STATUS
goes low. The user can change the parameter by AT command.
l Sleep mode timing scheme
Attention: Sleep mode is control by SLEEP.
8
l Reset mode timing scheme
3.Channel frequency
HM-TRLR series module have different working frequencies according to its model.
The frequencies have divided to 16 channel. Frequencies list is as follow(Black said Jumper).
Select Channel 433MHz Band 470MHz Band 868MHz Band 915MHZ Band
CH_1○○ 0
CH_2○○
430000000.00 470000000.00 863000000.00 915000000.00
CH_3○○
CH_4○○
CH_1●● 1
CH_2○○
430500000.00 470400000.00 863500000.00 915500000.00
CH_3○○
CH_4○○
CH_1○○ 2
CH_2●●
431000000.00 470800000.00 864000000.00 916000000.00
CH_3○○
CH_4○○
CH_1●● 3
CH_2●●
431500000.00 471200000.00 864500000.00 916500000.00
CH_3○○
CH_4○○
CH_1○○ 4 917000000.00
CH_2○○ 432000000.00 471600000.00 865000000.00
CH_3●●
9
CH_4○○
CH_1●● 5
CH_2○○
432500000.00 472000000.00 865500000.00 917500000.00
CH_3●●
CH_4○○
CH_1○○ 6
CH_2●●
433000000.00 472400000.00 866000000.00 918000000.00
CH_3●●
CH_4○○
CH_1●● 7
CH_2●●
433500000.00 472800000.00 866500000.00 918500000.00
CH_3●●
CH_4○○
CH_1○○ 8
CH_2○○
434000000.00 473200000.00 867000000.00 919000000.00
CH_3○○
CH_4●●
CH_1●● 9
CH_2○○
434500000.00 473600000.00 867500000.00 919500000.00
CH_3○○
CH_4●●
CH_1○○ 10
CH_2●●
435000000.00 474000000.00 868000000.00 920000000.00
CH_3○○
CH_4●●
CH_1●● 11
CH_2●●
435500000.00 474400000.00 868500000.00 920500000.00
CH_3○○
CH_4●●
CH_1○○ 12
CH_2 ○○
436000000.00 474800000.00 869000000.00 921000000.00
CH_3●●
CH_4●●
CH_1●● 13
CH_2○○
436500000.00 475200000.00 869500000.00 921500000.00
CH_3●●
CH_4●●
CH_1○○ 14
CH_2●●
437000000.00 475600000.00 870000000.00 922000000.00
CH_3●●
CH_4●●
CH_1●● 15
CH_2●●
437500000.00 476000000.00 870500000.00 922500000.00
CH_3●●
CH_4●●
10
4.Serial port check select

Module and controller using UART, we can select check mode((Black said Jumper).
Select Parity
U_EVEN○○ None Check
U_ODD ○○
U_EVEN●● EVEN Check
U_ODD ○○
U_EVEN○○ Odd Check
U_ODD ●●
5.Wireless rate
l When the HM-TRLR module is working on FSK modulation. The wireless rate conform to baud rate.
Theoretically it can transmit data boundless. We suggest that if the data package is too large ,you should use
the subcontract transmission in order to avoid the air data interference.
l When the HM-TRLR module is working on LoRa modulation. The wireless rate is depend on signal
bandwidth、spreading factor、coding rate、payload length.. However the receiver sensitivity is depend on
signal bandwidth and spreading factor. The following table shows the relationship between the wireless rate
and parameter.
Test conditions:
u Supply voltage = 3.3 V
u Temperature = 25° C
u CRC on payload enabled
u Payload length = 64 bytes
u Coding Rate = 1
SingnalBandWidth SpreadingFactor Sensitivity(dbm) ActualBandRate(pbs)

62.5kHz SF=7 -126 2169
62.5kHz SF=8 -129 1187
62.5kHz SF=9 -132 656
62.5kHz SF=10 -135 296
62.5kHz SF=11 -137 164
62.5kHz SF=12 -139 91
125kHz SF=7 -123 4338
125kHz SF=8 -126 2375
125kHz SF=9 -129 1312
125kHz SF=10 -132 733
125kHz SF=11 -133 328
125kHz SF=12 -136 183
250kHz SF=7 -120 8676
250kHz SF=8 -123 4750
250kHz SF=9 -125 2624
250kHz SF=10 -128 1466
250kHz SF=11 -130 778
11
250kHz SF=12 -133 366

500kHz SF=7 -118 17353
500kHz SF=8 -121 9501
500kHz SF=9 -124 5249
500kHz SF=10 -127 2932
500kHz SF=11 -129 1557
500kHz SF=12 -130 830
6.Frequency Hopping with LoRa

Frequency hopping spread spectrum (FHSS) is typically employed when the duration of a single packet could
exceed regulatory requirements relating to the maximum permissible channel dwell time. This is most notably the
case in US operation where the 902 to 928 MHz ISM band which makes provision for frequency hopping operation.
To ease the implementation of FHSS systems the frequency hopping mode of the LoRa modem can be enabled by
setting hopping period and Frequency step .
The formula relations:
HoppingPeriod(ms) = ( 2SF/BW)* FreqHoppingValue
SF = SpreadingFactor
BW = SingnalBandWidth
FreqHoppingValue = 1~255
FreqStep = 61Hz*FreqStepValue
FreqStepValue = 0~65535
7.Node ID Function with FSK

When HM-TRLR working in FSK. The module can be set up the node ID. When the ID function is enable ,The
sender first send the receiver node ID bytes, The receiver only receive with its node ID that matches the data. When
the Node ID function enable cases, The module can also set the broadcast ID function, If broadcast function enable,
The receiver can receive node ID of the data, but also receives the broadcast data.
Note: when the ID function is enabled, Interval time of two frame greater than Td time, The first byte of each frame
is a node ID or broadcast ID.
8. Td Delay time
l FSK modulate Td time

Data into RXD pin of module 1,Then data from module 2 TXD pin out, The time spent
The diagram below:
12
BandRate(bps) Td
1200 73ms
2400 37ms
4800 19ms
9600 10ms
14400 7ms
19200 6ms
38400 4ms
56000 3ms
57600 3ms
115200 2ms
l LoRa modulate Td time
In LoRa modulation, Wireless data transmission is the subcontract, If the length of data is more than payload length
and wireless rate less than the rate of serial port, The receiver of data will be interrupted. In the sending end, If the
receive buffer is full the STATUS will lower the output to prompt the user.
Wireless rate is greater than the rate of serial port, As the following figure.
Wireless rate is less than the rate of serial port, As the following figure.
13
Testing Conditions:
u Spread Factor = 9
u Singal Band Width = 250kHz
u Code Rate = 1
u PayLoad = 32 bytes
BaudRate（bps） Td
1200 Max 410ms
2400 Max 270ms
4800 Max 200ms
9600 Max 166ms
14400 Max 153ms
19200 Max 146ms
38400 Max 138ms
56000 Max 136ms
57600 Max 135ms
115200 Max 134ms
14
(三) HM-TRLR-S AT Instruction
1.Introduction
The controller through IO port make HM-TRLR-S transceiver been to configuration mode.Then through serial
port send AT command to Modify the performance parameters.
2.Command format
Command used capital letter ASCII to write and used <CR> to end. When to module receive command it will
explain and reply it.
2.1 Set the command format

The controller use command to set up HM-TRLR-S transceiver parameters. Command set AT as the
beginning,then command type and parameters, etc.
Command format: AT+CmdType=Para1,Para2…<CR>

Successfuly command reply: OK<CR>
Command fail reply:ERROR:n<CR>
2.2 Read Command format

The controller read command format to HM-TRLR-S transceiver parameter.Command set AT as the
beginning,then command type and question marks, etc.
Command format: AT+CmdType=?<CR>

Successfuly command reply: CmdType:Para1,Para2…<CR>
Command fail reply:ERROR:m<CR>
2.3 Return error parameters

When command execution error, the module will return ERROR: n.
parameter Value remark

m = 0：The command format is wr ng.
m 0~2 m = 1：The parameter is wrong.
m = 2：The command is failed.
15
3. Command type
3.1 Set Uart BaudRate command
The baudrate refers to the controller communication speed, when set, after the completion of new baudrate takes
effect immediately, The controller should with new baudrate and communication module.
Table 3-1.1 AT+SPR(SerialPortRate) command

Command type Command response remark
OK Succeed:OK ，
Set command AT+SPR=n
ERROR:m Failure:ERROR:m
+SPR:n Succeed: +SPR:n，
Read command AT+SPR=?
Table 3-1.2 Parameters

Parameter Range remark
0--1200bps 5--19200bps
1--2400bps 6--38400bps
n 0~9 2--4800bps 7--56000bps
3--9600bps 8--57600bps
4--14400bps 9--115200bps
3.2 Transmit power command

Transmit power command means the Transmit power of module.It will work
When the setting is completed and exit the configuration mode.
Table 3-2.1 AT+POWER command

OK Succeed:OK
Set command AT+POWER=n
+POWER:n Succeed:+POWER:n ，
Read command AT+POWER=?

0—20dbm 5—8dbm
1—17dbm 6—5dbm
n 0~7
2—15dbm 7—2dbm
3—10dbm
16
3.3 AT+SYNW command

Module sync word can be set by 1-8 bytes.Module can’t communicate with different sync word.
Table 3-3.1 AT+SYNW Command

OK Succeed:OK
Set command AT+SYNW=XXYYZZ…
+SYNW: XXYYZZ…
Read command AT+ SYNW =? Failure:ERROR:m
ERROR:m

XXYYZZ
Less than 16 characters Used 0~9，A~F character to express
…
For example :if sync word is “0x12,0x34,0xAB,0xEF”,Then AT command is :

“AT+SYNW=1234ABEF\r\n”
3.4 AT+SYNL (Syncwordlength) Command

Module sync word can be set by0-8 bytes.Module can’t communicate with different sync word. Suggest that the
sync word should more than 2. if is ‘0’ ,there is no sync word.
Table 3-4.1 AT+SYNL Command

OK Succeed:OK
Set command AT+SYNL=n
+SYNL: n
Read command AT+ SYNL =? Failure:ERROR:m
ERROR:m
Table 3-4.2 parameter

n 0~8
3.5 AT+NODE command

In FSK mode. The node function can be set.
Table 3-5.1 AT+NODE command

OK Succeed:OK
Set command AT+NODE=n,mode
+NODE: n,mode
Read command AT+ NODE =? Failure:ERROR:m
ERROR:m
17

0—Node function disable
n 0~1
1—Node function enable
mode 0~1 0—only match NID 1-match NID and BID
3.6 Node ID command

In FSK mode. The node ID can be set.
Table 3-6.1 AT+NID Command

OK Succeed:OK
Set command AT+NID=n…
+NID:n
Read command AT+ NID =? Failure:ERROR:m
ERROR:m

Parameter Range Instruction
0 0~255
3.7 AT+BID command

In FSK mode ,AT+BID can be set.
Table 3-7.1 AT+BID command

OK Succeed:OK
Set command AT+BID=n…
+BID:n
Read command AT+ BID =? Failure:ERROR:m
ERROR:m

0 0~255
3.8 AT+LRCRC command

In LoRA mode,CRC Function enable or disable
Table 3-8.1 AT+LRCRC command

OK Succeed:OK
Set command AT+LRCRC=n
+LRCRC:n
Read command AT+LRCRC=? Failure:ERROR:m
ERROR:m

Range remark
Parameter
0-disabe CRC function
n 0~1
1-enable CRC function
18
3.9 LoRa Signal Band Width choose command.

In the LoRa mode, According to the demand to set signal band width. The larger this value, then
Wireless rate is faster.
Table 3-9.1 AT+LRSBW(Signal Band Width)command

OK Succeed:OK
Set command AT+LRSBW=n
+LRBW:n Succeed: +LRSBW:n，
Read command AT+LRSBW=?

6—62.5KHZ
n 6~9 7—125KHZ
8—250KHZ
9—500KHZ
3.10 LoRa spreading factor choose command

When the module in the Lora mode. You can set spreading factor according to the demand.
If the larger the value of SF, The higher receiving sensitivity and the slower of wireless rate
Table 3-10.1 AT+LRSF(Spreading Factor) command

OK Succeed:OK
Set command AT+LRSF=n
+LRSF:n Succeed: +LRSF:n，
Read command AT+LRSF=?
Table 3-10.2 Parameter

Param
Range remark
eter
7—SF=7 A—SF=10
8—SF=8 B—SF=11
n 7~C
9—SF=9 C—SF=12
19
3.11 LoRa Forward Error Correction Code choose command.

When the module in the LoRa mode.Data transfer adopt Forward Error Correction Code ,this command is choose
it Coding Rate.
Table 3-11.1 AT+LRCR(Coding Rate)Command

OK Succeed:OK
Set command AT+LRCR=n
+LRCR:n Succeed: +LRCR:n,
Read command AT+LRCR=?

0—CR4/5
1—CR4/6
n 0~3
2—CR4/7
3—CR4/8
3.12 LoRa hopping enable command.

When the module in the LoRa mode, module has FHSS function.
Table 3-12.1 AT+LRHF(HFSS) Command

OK Succeed:OK
Set command AT+LRHF=n
+HFSS:n Succeed: +HFSS:n,
Read command AT+LRHF=?

Param
Rang remark
eter
0-disable HFSS function
n 0~1 1- enable HFSS function
note: when SBW=500kHz and SF =12, HFSS function disable
20
3.13 LoRa Data packet Length set command.

When the module in the LoRa mode.Data transmission in the form of subcontract, this command to set the length
of data packet.
Table 3-13.1 AT+LRPL(Packet Length) Command

Command type Command response Instruction
OK Succeed:OK
Set command AT+LRPL=n
+LRPL:n Succeed: +LRPL:n
Read command AT+LRPL=?

Paramete
Range Instruction
r
1~127 data rang is 1~127byte
n 1~127
suggest: more than 16
3.14 LoRa hopping period value command.

When the module in the LoRa mode, the hopping period value can be set.
Table 3-14.1 AT+LRHPV(Hopping Period Value) Command

OK Succeed:OK
Set command AT+LRHPV=n
+LRHPV:n Succeed: +LRHPV:n
Read command AT+LRHPV=?

n 0~255 Suggest: More than 5
3.15 LoRa Frequency Step Value command.

When the module in the Lora mode, Frequency Step Value can be set.
Table 3-15.1 AT+LRFSV(Frequency Step Value) command
AT+LRFSV=n OK Succeed:OK
Set command
AT+LRFSV=? +LRFSV:n
Read command Failure:ERROR:m
ERROR:m

n 0~65535
21
3.16 Mode command

The modulation of HM-TRLR can be changed,
Table 3-16.1 AT+MODE Command

OK Succeed:OK
Set command AT+MODE=n
+MODE:n
Read command AT+MODE =? Failure:ERROR:m
ERROR:m

0-LoRa Mode
1-OOK Mode
n 0~3 2-FSK Mode
3-GFSK Mode
In the OOK mode，baudrate no more than 9600 bps
3.17 AT+BAND Command

Frequence band can be changed.
Table 3-17.1 AT+BAND Command

OK Succeed:OK
Set command AT+BAND=n
+BAND:n
Read command AT+BAND=? Failure:ERROR:m
ERROR:m

0--434MHZ Band
1--470MHZ Band
n 0~3
2--868MHZ Band
3--915MHZ Band
3.18 Test command

Connect test .
Table 3-18.1 AT Command
OK
command AT Failed: ERROR:m
ERROR:m
22
3.19 AT&W command

When parameters was changed. HM-TRLR can't save parameters into Flash Memory automatically .
If you want to permanently save the parameters, use the AT&W command for save.
Notice: written times of Flash memory are limited. To avoid damage, the written times within 10000 times is the
best.
Table 3-19.1 AT&W command
OK
Set command AT&W Failed: ERROR:m
ERROR:m
3.20 Default setting

1)HM-TRLR-D-YYY-433 Module default setting
Command default remark
AT+SPR=n n=3 Baud rate 9600pbs
AT+POWER=n n=0 Power 20dbm
AT+SYNL=n n=6 6 bytes
AT+NODE=n,mode n=0,mode=0 Disable ID Node function
AT+LRCRC=n n=1 Lora mode,CRC enable
AT+LRSBW=n n=7 SBW = 125KHz
AT+LRSF=n n=9 SF = 9
AT+LRCR=n n=0 CodeRate=4/5
AT+LRHF=n n=0 FHSS is disable
AT+LRPL=n n=32 Package lenth 32bytes
AT+LRHPV=n n=10 Hopping period
AT+LRFSV=n n=1638 Frequence step 100KHz
AT+MODE=n n=0 LoRa mode
AT+BAND=n n=0 433MHz band

AT+BAND=n n=1 470 MHz band
23


24
4、Document Change List
版本号章节变更描述日期
1.0 All Initial released version 2014-3
1.1 Page3 Parameter Update the Sleep Current 2016-3
This document may contain preliminary information and is subject to

change by Hope Microelectronics without notice. Hope Microelectronics
assumes no responsibility or liability for any use of the information
HOPE MICROELECTRONICS CO.,LTD contained herein. Nothing in this document shall operate as an express or
Add: 2/F, Building 3, Pingshan Private implied license or indemnity under the intellectual property rights of Hope
Enterprise Science and Technology Microelectronics or third parties. The products described in this document
Park, Lishan Road, XiLi Town, are not intended for use in implantation or other direct life support
Nanshan District, Shenzhen, applications where malfunction may result in the direct physical harm or
Guangdong, China injury to persons. NO WARRANTIES OF ANY KIND, INCLUDING, BUT
Tel: 86-755-82973805 NOT LIMITED TO, THE IMPLIED WARRANTIES OF MECHANTABILITY
Fax: 86-755-82973550 OR FITNESS FOR A ARTICULAR PURPOSE, ARE OFFERED IN THIS
Email: [email protected] DOCUMENT.
Website: http://www.hoperf.com
http://www.hoperf.cn ©2006, HOPE MICROELECTRONICS CO.,LTD. All rights reserved.

HM-TRLR-D Series - EN - V1.1

Uploaded by

Copyright:

Available Formats

HM-TRLR-D Series - EN - V1.1

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HM-TRLR-D Series - EN - V1.1

Uploaded by

Copyright:

Available Formats

HM-TRLR-D Series 100mW LoRa Transceiver ver1.

Figure 2. HM-TRLR-D Series Pin Description

Parameter Min Max Unit

Parameter Condition Min Typical Max Unit

HM-TRLR-D-YYY-470 450 470 490

HM-TRLR-D-YYY-915 895 915 935

LoRa SBW= 500KHz

7. HM-TRLR-D Series Application Circuit

Figure 3.HM-TRLR-D TTL UART Simple Application

Figure 4. HM-TRLR-D RS232 Simple application

Figure 5. HM-TRLR-D RS485 Simple application

Figure 6.HM-TRLR-D TTL UART Complete Application

8. Mechanical Dimension（size unit：mm）

Part Number=Module type – Package type – Interface type – Operation band

Part Number Interface Operation Band

Table 4: Part Number list

（二）Operation and Applications

l Running mode timing scheme

l Configuration mode scheme

l Sleep mode timing scheme

Attention: Sleep mode is control by SLEEP.

l Reset mode timing scheme

4.Serial port check select

SingnalBandWidth SpreadingFactor Sensitivity(dbm) ActualBandRate(pbs)

250kHz SF=12 -133 366

6.Frequency Hopping with LoRa

7.Node ID Function with FSK

l FSK modulate Td time

l LoRa modulate Td time

(三) HM-TRLR-S AT Instruction

2.1 Set the command format

Command format: AT+CmdType=Para1,Para2…<CR>

2.2 Read Command format

Command format: AT+CmdType=?<CR>

2.3 Return error parameters

parameter Value remark

Table 3-1.1 AT+SPR(SerialPortRate) command

Table 3-1.2 Parameters

3.2 Transmit power command

Table 3-2.1 AT+POWER command

Table 3-2.2 Parameters

3.3 AT+SYNW command

Table 3-3.1 AT+SYNW Command

Table 3-3.2 Parameters

For example :if sync word is “0x12,0x34,0xAB,0xEF”,Then AT command is :

3.4 AT+SYNL (Syncwordlength) Command

Table 3-4.1 AT+SYNL Command

Table 3-4.2 parameter

3.5 AT+NODE command

Table 3-5.1 AT+NODE command

Table 3-5.2 parameter

3.6 Node ID command

Table 3-6.1 AT+NID Command

Table 3-6.2 parameter

3.7 AT+BID command

Table 3-7.1 AT+BID command

Table 3-7.2 parameter

3.8 AT+LRCRC command

Table 3-8.1 AT+LRCRC command