MorphoWave Compact

Quick User Guide

2018_2000035854 – V1

All descriptions, illustrations, and specifications in this brochure should be

considered approximate and may relate to optional equipment or feature

IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED

 Table of Contents
Color Step Content
One Overview
Two Wiring
Three Communication
Four SDAC (Single Door Access Control)
Five Administration
Six Software
Seven Enrollment
Eight Optional features

2 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Regulatory, safety and environmental notices
Products bearing the CE marking comply with one or more of the following EU Directives as may be applicable:

• Low Voltage Directive 2006/95/EC

• EMC Directive 2004/108/EC

• R&TTE Directive 1999/5/EC

• Ecodesign Directive 2009/125/EC

• RoHS Directive 2011/65/EU.

Compliance with these directives is assessed using applicable European Harmonised Standards.<<<

The installation of this product should be made by a qualified service Person and should comply with all local regulations.

It is strongly recommended to use a class II power supply at 12V-24V and 2.5 A. min (at 12V) in conformity with Safety Electrical Low Voltage
(SELV). The power supply cable length should not exceed 10 meters.
This system must be installed in accordance with the National Electrical Code (NFPA 70), and the local authority having jurisdiction.

This product is intended to be installed with a power supply complying with IEC60950-1, in accordance with the NEC Class 2 requirements; or
supplied by a listed IEC60950-1 external Power Unit marked Class 2, Limited Power source, or LPS and rated 12VDC, 2.5 A minimum or 24VDC,
1.25 A minimum.

In case of building-to-building connection it is recommended to connect 0V to ground. Ground cable must be connected with the terminal block
Power Ground.

Note that all connections of the MorphoWave Compact terminal described hereafter are of SELV (Safety Electrical Low Voltage) type.

This symbol means do not dispose of your product with your other household waste. Instead, you should protect human health and the environment
by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment.

3 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Product Overview
Speaker
MorphoWave Compact provides an Status LED
innovative and effective solution for access
control applications using very fast
acquisitions of four (4) fingerprints without Contactless 4.3'’ WVGA
any contact. card area touchscreen LCD

Access control and Time & Attendance Microphone

Biometric authentication by a hand swipe through the Hand proximity
active volume without contact sensor
IDEMIA False finger detection algorithms
Contactless
Simple and ergonomic man-machine interface biometric sensor

Contactless card reader (MIFARE Classic, MIFARE

Plus, DESFire, HID® Iclass*, HID® PROX*)
Intercom system

Step one : overview

Optional Wifi
Universal connectivity (Gigabit Ethernet, Wi-FiTM, interface
RS485/422, Wiegand, Dataclock)
Anti-tamper sensor

* Depending on product version

4 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 MorphoWave Compact Checklist

Product packaging checklist:

QTY ITEM
1 MorphoWave Compact terminal
1 Wall Mounting Plate
1 Documentation package

Step one : overview

Electronic documentation is provided in Adobe® Acrobat® format (PDF). Adobe® Acrobat® Reader is available at http://www.adobe.com.

5 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Terminal Implementation
To secure an access, IDEMIA recommends installing the MorphoWave Compact terminal as a part of a typical Access Control system,
which consists of the components described below.

A The MorphoWave Compact terminal

Its role is to process the access request from the user. It performs access right
checks using one-to-many biometric identification or one-to-one biometric
verification, and/or RF card authentication, and/or PIN check.
An Access Controller (3rd party product)
C B
The terminal interfaces with an Access Controller (using TCP/IP, Wiegand,
Data Clock, RS485 or RS422 protocol):
A
B After access request, the terminal sends the result of user’s access rights to
the Access Controller (this message contains at least the User ID)
MorphoWave Compact The Access Controller performs additional checks, and returns the final
Terminal
decision (access granted/denied) to the terminal (which displays the result to
the user), and to the door controller which opens the door (if the access has
D been granted).

Step one : overview

C An Alarm (3rd party product)
The terminal sends a message to the Access Controller, to activate the Alarm as
soon as a malicious activity, such as tamper or pulling, is detected

D A Door Electric Latch or equivalent (3rd party product)

The Access Controller sends a command to activate the latch if the access is granted (i.e. if the individual's User ID is listed in the Controller
authorized user List). Control of the latch is made through a dry contact..

6 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Typical Access Control Process

If the user is allowed

If the result of the to access to the
check is successful protected zone, the
On Access Request, (access granted), a central access
the terminal checks message is sent to controller returns an
user’s access rights the Central Access "access granted"
using a biometric Controller for message to the
check. additional access terminal and a “open”
rights check. command to the gate
controller.

Note: One user must be enrolled in the terminal database, in order to be able to perform biometric check.

7 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Access Control Modes
The terminal can be configured in one of the modes described in the table below
Identification Authentication Multifactor Proxy
Access Application that runs Application that runs Application that runs Remote application
control on the terminal when on the terminal when on the terminal when that controls the
application it starts. it starts. it starts. terminal through
network commands
Access A user swipes his/her A user places a Both Identification Triggering events are
control hand in the biometric contactless card in and Authentication selected by the
triggering sensor. front of the reader. (*) triggers are enabled. remote application
event
Biometric The user’s captured The user’s captured As per Identification Selected by the
check (if fingerprints are fingerprints are or Authentication, remote application
enabled) matched against all matched against depending on the
fingerprints in the their reference triggering event
terminal database. fingerprints. (**)

Step one : overview

Decision to By Identification By Authentication By running By remote
display result standalone standalone standalone application
signal to user application or application or application or
controller feedback controller feedback controller feedback
(* ) or the user enter their Identifier on the keypad, or a Wiegand frame is received from an external device
(**) stored on the contactless card or in the user record in the terminal’s local database

8 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Deployment Environment
Operating temperature -10°to + 55 °C (14°to 131°F) when ECO-Mode ON
-10°to + 45 °C (14°to 113°F) when ECO-Mode OFF
Operating humidity 10 % < RH < 80 % (non condensing)
Storage temperature -25°to + 70 °C (-13°to 158°F)
Storage humidity 5% < RH < 95 %
IP code IP65 rated
Do not deactivate ECO-mode when working at a temperature above 45°C (113°F), to avoid over-
heating.

General precautions
Do not expose the terminal to extreme temperatures.
When the environment is very dry, avoid synthetic carpeting near the MorphoWave Compact terminal, to
reduce the risk of unwanted electrostatic discharge.
Areas containing combustibles

Step one : overview

Do not install the terminal in the vicinity of gas stations or any other installation containing flammable or
combustible gases or materials. The terminal is not designed to be intrinsically safe.
The terminal should be installed in controlled lighting conditions
Avoid exposure of the biometric sensor to direct sunlight.

9 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Wiring Overview Pin numbers shown in this document correspond to the
internal connector pinout in the product. The connector
RJ-45 : Ethernet & PoE attached to the cable is for test only and should be removed
1 ETH TX+ Orange / White for installation.
2 ETH TX- Orange
3 ETH RX+ Green / White
4 ETH VPORT+ Blue
RJ45
5 ETH VPORT+ Blue / White RS-422 and 485
6 ETH RX- Green 7 RS485_RX_A Blue / Black
7 ETH VPORT- Brown / White 8 RS485_TX_Z Green / White
8 ETH VPORT- Brown 9 RS485_RX_B Blue / White
Shell ETH GND Drain wire (no color) GPIO
10 RS485_TX_Y Green / Black
19 GPI2 Orange / Black
11 RS485_GND Black / Red
20 GPO2 Yellow / Red
17 GPI1 Orange / Red Wiegand IN & Wiegand OUT
18 GPO1 Yellow / Red 25 WIEGAND_LEDOUT1 Blue
Power supply & Tamper switch 15 GPI0 Orange 28 WIEGAND_LEDOUT2 Blue / Red
13 RLY_NC Orange / White 16 GPO0 Yellow 23 WIEGAND_IN1 White / Red
14 RLY_NO Yellow / White 22 GPIO_GND Black / Red 24 WIEGAND_OUT0 Green
12 RLY_COM Grey / White 26 WIEGAND_OUT1 White
5 SWITCH_PIN1 Light Blue 21 WIEGAND_IN0 Green / Red
6 SWITCH_PIN2 Pink 27 WIEGAND_GND Black / Red
1,3 Power + 12V Red
2,4 Power GND Black

All connections of the terminal are of SELV (Safety Electrical Low Voltage) type.

Step two : wiring

Power supply from electrical source shall be switched off before starting the installation.
Before proceeding, make sure that the person in charge of installation and connections, is properly connected to
earth, in order to prevent Electrostatic Discharges (ESD).

Backup of the Date/Time of the terminal: the volatile settings (such as date/time) of the terminal are protected against
power failure, by a dedicated component during a least 24 hours (at 25 oC) without external power supply.

10 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Power supply
Power Over Ethernet (POE+): power can be provided through RJ-45 connector
RJ45 using a PSE (Power Sourcing Equipment) IEEE802.3at type 2 compliant.
The terminal is a Class 4 (25.5 W) PD (Powered Device).

PoE+ Injector Specs

 Output Voltage: 48 VDC
1-3 Power + 12V Red  Output Current: 0.64 A
2-4 Power GND Black  Power: 30 W

External Power Supply: 12-24 Volts (regulated and filtered) 2.5 Amp min @12 V, CEE/EEC EN60950
standard compliant. If sharing power between devices, each unit must receive 2.5 A (e.g. two units would
require a 12 VDC, 5 A supply).

A battery backup or uninterrupted power supply (UPS) with built-in surge protection is recommended.

IDEMIA recommends using a 24V power supply and AWG16 gauge Maximum distance (meters)
cable. The voltage measured on the product block connector of the Gauge Section
vs power source rating
terminal must be equal to 12V-24V (-15% / +10%). AWG (mm2)
12V+/-10% 12V+/-5% 24V+/-10%

Step two : wiring

16 1.31 9m 20 m 300 m
The voltage drop due to the cable shall be taken into account. The
table at the right, shows the maximum distance between power 18 0.82 6m 12 m 200 m
supply and 1 unique device, depending on cable gauge and power 20 0.52 3m 8m 120 m
supply rating. 22 0.32 2m 5m 75 m

WARNING: Under powering may cause memory and data corruption; over powering may cause hardware damage.
Both of these situations will void the warranty

11 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 RS-485 Communication
RS-232 to
RS-232 RS-485
from the RS-485 to
converter
Com Port 1200m (4000ft)

For RS-485 installations, the cable should be run in a daisy-

8 RS485_TX_Z (-) Green / White chain configuration (i.e. converter > position 1 > position 2 >
10 RS485_TX_Y (+) Green / Black position 3, etc.).
11 RS485_GND Black / Red
Choose a RS-232 to RS-485 converter that supports Sense
Data to switch from Send to Receive mode.

Step three : communications

Use CAT-5 UTP (or better) cable (shielded recommended) with a characteristic impedance of 120 ohms.
AWG 24 should be the minimum wire gauge used.

Choose one twisted pair of conductors to use for RS485_TX_Y (TX+, Green / Black wire - 10) and RS485_TX_Z (TX-, Green
/ White wire - 8). Another conductor should be used for Signal Ground (Black / Red wire - 11).

IMPORTANT:
 A maximum of 31 devices may be installed on the same line.
 The maximum total cable length is 4000 ft. (1200m).
 The cable must be dedicated to this installation and not used for any other purpose

12 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 RS-422 Communication
RS-232 to
RS-232 RS-422
from the RS-422 to
converter
Com Port 1200m (4000ft)

For RS-422 installations, the cable should be run in a point to

7 RS485_RX_A (RX+) Blue / Black
point configuration (i.e. PC > converter > terminal)
8 RS485_TX_Z (TX-) Green / White
9 RS485_RX_B (RX-) Blue / White
10 RS485_TX_Y (TX+) Green / Black
Use CAT-5 UTP (or better) cable (shielded recommended)
11 RS485_GND Black / Red with a impedance of 120 . AWG 24 should be the minimum
wire gauge used.

Step three : communications

Choose one twisted pair of conductors to use for RS485_TX_Y (TX+, Green / Black wire - 10) and RS485_TX_Z (TX-, Green
/ White wire - 8).
Choose one twisted pair of conductors to use for RS485_RX_A (RX+, Blue / Black wire - 7) and RS485_RX_B (RX-, Blue /
White wire - 9).
Another conductor should be used for Signal Ground (Black / Red wire - 11).

The maximum total cable length is 4000 ft. (1200m).

The cable must be dedicated to this installation and not used for any other purpose

13 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Ethernet and Wireless LAN
1 ETH TX+ Orange / White
2 ETH TX- Orange
3 ETH RX+ Green / White
4 ETH VPORT+ Blue Wireless
5 ETH VPORT+ Blue / White RJ45
6 ETH RX- Green
7 ETH VPORT- Brown / White
8 ETH VPORT- Brown
Shell ETH GND Drain wire (no color)

LAN Ethernet

Management
Use a category 6 shielding cable (120 Ohms) or better. It is strongly recommended

Step three : communications

station
to insert a repeater unit every 90 m.

Static mode is enabled by default on MorphoWave Compact terminals (factory

setting) : IP=192.168.1.10, Gateway=192.168.1.254, Mask= 255.255.254.0
WLAN option
IDEMIA wireless enabled
Terminal Block Ethernet connection
devices support 802.11b and
Extreme care must be taken while connecting Ethernet wire to the block board
802.11g standards. WEP
since low quality connection may strongly impact Ethernet signal sensibility.
Open, WPA and WPA2 are
Connect Rx+ and Rx- with the same twisted-pair wire (and do the same with
supported.
Tx+/Tx- and the other twisted-pair wire).

14 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Wiegand Communication
25 WIEGAND_LEDOUT1 Blue LED
28 WIEGAND_LEDOUT2 Blue / Red Out
23 WIEGAND_IN1 White / Red
24 WIEGAND_OUT0 Green
26 WIEGAND_OUT1 White
Wiegand In
21 WIEGAND_IN0 Green / Red
27 WIEGAND_GND Black / Red Wiegand Out

LED In
16 GPO0 Yellow

Three-conductor cable (shielded recommended) is required for Data 0, Data 1, and WGND.

Step three : communications

Use 18-22 AWG cable in a homerun configuration from each unit to the Access Control Panel (ACP).
Connect WIEGAND_OUT0 (Green wire – Pin 24) to ACP Data 0,
Connect WIEGAND_OUT1 (White wire – Pin 26) to ACP Data 1,
Connect WIEGAND_GND (Black / Read wire – Pin 27) to ACP reader common (0vDC).

For 18 AWG, the maximum cable distance is 500 ft. (150m); for 20 AWG, the maximum is 300 ft. (90m); for 22
AWG, the maximum is 200 ft. (60m).

All controller output shall be open drain or 5 V +/- 5%

15 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Wiegand Communication (continued)
Important Example Format Information
By default, the Wiegand output format is not enabled. Wiegand Type: Standard 26-bit
output must be configured before connecting to the ACP.  Alt Site Code and Fail Site Code Range: 0-255
Note  Template ID Number Range: 1-65535
On installation, the system administrator will be prompted to  Extended ID Number Range: N/A
select either a pre-existing Wiegand frame format or create a  ID Start Bit: 9
custom format, and upload it to the unit before the first use.  Length of ID: 16
Data Clock  Site Code Start bit: 1
The Wiegand port also supports the Clock & Data protocol.  Length of Site Code: 8
The wiring is described below.  Start Bit length : 0

Step three : communications

25 WIEGAND_LEDOUT1 Blue LED
28 WIEGAND_LEDOUT2 Blue / Red Out
23 WIEGAND_IN1 White / Red Clock
24 WIEGAND_OUT0 Green Data
26 WIEGAND_OUT1 White Clock
21 WIEGAND_IN0 Green / Red Data Data Clock In
27 WIEGAND_GND Black / Red Data Clock Out

Card present
16 GPO0 Yellow
(Legacy Morpho Mode)

16 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Single Door Access Control (SDAC)
Single Door Access Control (SDAC) wiring sample : with Push Button

See details on next page

for relay connection
13 RLY_NC Orange / White
14 RLY_NO Yellow / White
Deadbolt / Door strike
12 RLY_COM Grey / White Power
supply

17 GPI1 Orange / Red Door contact

18 GPO1 Yellow / Red
Power
15 GPI0 Orange
supply
16 GPO0 Yellow
Push Button

Step four: SDAC

If door contact is not used, GPI1 (17) and GPO1 (18) shall be connected together

Power supply from electrical source shall be switched off before starting the installation.

17 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Internal Relay Wiring
Protection Diode
RJ45 Power supply
VCC < 30V
Imax < 1A
Deadbolt /
Door strike Warning
This is recommended only for
small or stand-alone
13 RLY_NC Orange / White Push Button applications where access
14 RLY_NO Yellow / White on other side control panels are not available.
12 RLY_COM Grey / White of the door
In this mode it is strongly
recommended to monitor the
Example for Normally
Tamper Detection of the device
Open connection

Inductive load management requires a parallel diode for a better contact lifetime.

Step four: SDAC

Warning
 The internal relay is limited to a maximum current of 1A @ 30V. If the deadbolt / door strike draws
more than 1A, damage to the device may occur. If the deadbolt / door strike load exceeds 1A, an
external relay must be used.
 The internal relay is designed for 100.000 cycles. If more cycles are needed, an external relay
driven by GPO must be used.

18 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Local Administration - First Boot Assistant
The First Boot Assistant (FBA) helps the administrator to Main settings managed by FBA
configure all the device fundamental settings.
Date & Time & Time Zone Settings
It is automatically launched at first terminal startup, but can
also be launched on demand, though administration menu Trigger Event: select event(s) to be processed
(i.e. to reinitialize terminal main settings) as an access request by a user

Language Settings: user interface language

selection,

Network Settings: LAN or WLAN parameters

Password Settings: terminal administration

password modification

Boot assistant at next boot: Display this

screen on next boot.

Step five: Administration

19 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Local Administration – Using Touch Screen Menu
Frequently used icons

Back (and Exit or Go

Cancel) Home

User Multimedia
Cancel Validation or management management
or refuse confirmation

+ password Terminal Communication

(default: 12345) settings settings

Step five: Administration

Terminal Restart
For security reasons, it security terminal
is highly recommended
to change the devices
default password to a
custom password. USB key Information
management about terminal

20 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Administration with MorphoBioToolBox application
The MorphoWave Compact Series
Terminal administration with MorphoBioToolBox (MBTB) application
terminal can be configured using a
dedicated (Windows) application :
MorphoBioToolBox
Please note that this application has
an embedded User Guide (Help
menu).

North and South America :

E-mail [email protected]
with your name, phone number, serial
number of your MorphoWave Compact
and “Please Send Link for MBTB” in the
subject of your e-mail. A link to download
the software will be e-mailed to you.

Step five: Administration

Other countries : please contact your
sales representative.

21 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Software for Terminal Remote Administration

MorphoWave Compact Series terminals are fully compatible with:

MorphoManager application (version 12 or higher)

Step six : Software

22 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Local Enrollment Process 1/2
A new user can easily be added by using the administration menu of the
MorphoWave Compact terminal.
This “local enrolment” is recommended only for small or stand alone
installations or testing purposes. For professional systems enrolment should
be performed remotely with an enrolment station, which is a PC with a
dedicated application such as MorphoManager.

This menu allows a user’s record to be added in the local database, with the
option of creating a user RF card, with the user’s reference data.

Enrolment gathering user’s data listed :

User’s first name and last name
User’s fingerprints (for biometric check)
User’s administration rights (none, settings, database)
User’s PIN (for PIN check)
User’s duress fingerprint
User’s access schedule and holiday schedule

Step seven: capture basics

User’s dynamic message setting
User’s record expiry date
User to include in white list or in VIP list
User specific access rules definition

MorphoWave Compact terminal allows you to capture up to 8 fingers per

user.
Note: Refer to User enrollment section in MorphoWave Compact
Administration Guide.

23 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Local Enrollment Process 2/2

Step seven: capture basics

NB: To complete enrollment,
two waves are required.

24 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Acquisition guidelines 1/2
Ideal acquisition procedure

1. Insert your hand flat, palm 2. Slightly spread apart your

down, from the front of the fingers
scanner

Step seven: capture basics

3. Place your hand between the 4. Position your fingertips
cover and the optical sensor according to the marking on
the left/right side of the
acquisition area

5. Slide your hand from right to

left or left to right
25 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Acquisition guidelines 2/2
Improper use

7. Do not touch the cover 8. Do not place your hand on the

optical sensor

1. Do not place your hand upside 2. Do not cross your fingers

down

9. Do not place your hand on the 10. Do not place your hand too far
edge of the optical sensor up on the optical sensor

Step seven: capture basics

3. Do not place your hand with 4. Do not place your fingers
fingers spread wide tightly together

11. Do not tilt your hand (left to 12. Do not insert your hand fingers
right or fingertip to palm)” first from either the left or right
side of the scanner

5. Do not place 2 hands inside 6. Do not place your hand on the

13. Do not swipe your hand too fast
cover
26 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Contactless Card Position – PIN input
Contactless Card Position Input PIN
This action is required once
during the user enrolment
process (generation /
encoding of a user RF card),
and at each authentication.

Place user’s RF card in front

of embedded contactless
card reader which is located
behind the contactless logo.

Step seven: capture basics

The authentication process is initiated by the detection When defined by terminal settings, the user is required
of a user card by the contactless card reader. to enter his PIN code, once during enrolment process,
and at each authentication (in addition or instead of
biometric check).
The terminal reads the user data stored in the card (at
least the User ID), and starts the authentication The PIN code is entered using a numeric keypad
process, as defined by the terminal settings. displayed on the LCD touch screen.
27 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Time and Attendance feature
MorphoWave Compact Series terminals support an optional Time and
Attendance (T&A) feature.

For this, the terminal adds a specific T&A information to each

identification or authentication record stored in the embedded event log
database.

This information is provided by the user through a specific screen

displayed during identification or authentication process.

The new screen contains 4 dedicated function keys :

Entry
Exit

Step eight: optional features

Beginning of a task
Ending of a task

The user is expected to press one of the keys to provide the specific
Time & Attendance information to the terminal.

Depending on terminal settings, this screen is displayed before or after

the user waves his/her hand in the sensor or his/her card in front of the
reader.
An extended mode is also available with 16 function keys.

28 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Recommendations
The manufacturer cannot be held responsible in case of non-compliance with the following recommendations or incorrect use of the terminal.

Repair and Accessories

Do not attempt to repair the MorphoWave Compact Series terminal yourself. The manufacturer cannot be held responsible for any
damage/accident that may result from attempts to repair components. Any work carried out by non-authorized personnel will void your
warranty.
Only use the terminal with its original accessories. Attempts to use unapproved accessories with your terminal will void your warranty.

Standalone terminals (not connected to a network)

For terminals used in standalone mode, it is strongly recommended to regularly backup the local database, and at least after significant
changes in the database (add, remove or modification of user’s records), on a external support such a mass storage key

Date / Time synchronization

The MorphoWave Compact Series terminal clock has a +/- 10 ppm typical time deviation at +25°C (roughly +/- 1sec per day). At lower and
higher temperature, deviation may be greater (maximum : 8 seconds per 48 hours).
When the terminal is used for applications requiring high time precision, it is strongly recommended to synchronize the terminal with an
external clock.

Cleaning precautions
A dry cloth should be used to clean the terminal, especially the biometric sensor.
The use of acid liquids, alcohol or abrasive materials is prohibited.
Use dry air spray to remove the dust out of the sensor glass

Firmware release
To get the best of our technology, we recommend you to download and install the last firmware release (please refer to last page)

29 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Documentation
Documents about installing the terminal
MorphoWave Compact Installation Guide, Ref. 2018_2000035853
This document describes the terminals physical mounting procedure, electrical interfaces and connection procedures.

Documents about administrating / using the terminal

MorphoWave Compact Quick User Guide, Ref. 2018_2000035854
This document gives a quick overview of the product and the basics of configuration and use.

MorphoWave Compact Administration Guide, Ref. TBD

This document describes the different functions available on the terminal and the procedures for configuring the terminal. It also contains the
full description of all the configuration parameters for the terminal.

MorphoWave Compact Parameters Guide, Ref. TBD

This document contains the full description of all the terminal configuration parameters.

Documents for the developer

MorphoWave Compact Host System Interface Specification, Ref. TBD
This document describes the commands supported by the MorphoAccess® terminal.

MorphoWave Compact Remote Message Specification, Ref. TBD

This document describes the format of messages sent by the terminal to a distant system.

Release note : for each firmware version, a release note is published describing the new features, the supported products, the potential known
issues, the upgrade / downgrade limitations, the recommendations, the potential restrictions…

North and South America: you may obtain these document by e-mailing [email protected] with your name, phone number,
MorphoWave Compact serial number and “Send Links For MorphoWave Compact Documents” in the subject line.
Other countries: please contact your sales representative.

30 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED
 Contacts
Technical Support and Hotline

North America South Africa

Gitis Ref TBD

Mail: [email protected] Mail: [email protected]
Tel: +1 888 940 7477 Tel: + 27 11 286 5855

South America Europe and rest of the world

Mail: [email protected] Mail: [email protected]
Tel: +1 714 575 2973 Tel: +33 1 30 20 30 40
(9H00am to 5H30pm French Time, Monday to Friday)
India
Mail: [email protected]
Tel: 0120-4699900

For the latest firmware, software, document releases, and news, please check our websites :
North and South America : e-mailing [email protected] with your name, phone number, MA
SIGMA Extreme serial number and “Send Links For MorphoWave Compact Documents” in the subject line
Other countries : please visit our web site www.biometric-terminals.com (To get your log in and password please
contact your sales representative).

Copyright © 2018, IDEMIA. All rights reserved.

www.idemia.com
Reproduction in whole or in part in any form or medium without the express written permission of IDEMIA is prohibited.
The trademarks identified herein are the trademarks of registered trademarks of IDEMIA, or other third party.

31 IDEMIA - 2018_2000035854 – V1
IDEMIA DOCUMENT – REPRODUCTION AND DISCLOSURE PROHIBITED