Product Bulletin Fisher 8532 High Performance Butterfly Valve en 123262
Product Bulletin Fisher 8532 High Performance Butterfly Valve en 123262
Product Bulletin Fisher 8532 High Performance Butterfly Valve en 123262
www.Fisher.com
Product Bulletin
51.6:8532 8532 Valve
January 2023 D101552X012
Specifications
Available Valve Configurations Backup ring: J Nitrile, J Chloroprene, J PTFE,
J Wafer (Flangeless), J Lugged (Single Flange), or J Fluorocarbon--for a broad range of hydrocarbon
J Double Flanged valve bodies and chemical process applications(1) or J EPR--for
process applications including steam and water(1). A
Valve Body Sizes backup ring is not used with the NOVEX seal
NPS J 14, J 16, J 18, J 20, J 24, J 30, J 36, Packing: J PTFE V-ring (standard packing),
J 42, and J 48 J Graphite (optional), or J ENVIRO-SEAL packing
(optional)
End Connection Style
Bearings: J PEEK(2) (standard material), and
J NPS 14 through 24 valve bodies designed to fit
J S31600, J PTFE Composition, or J CoCr-A (Alloy
between ASME B16.5 raised-face mating flanges
6) (optional)
J Larger than NPS 24 valve bodies designed to fit
between ASME B16.47 Series A mating flanges Gaskets: J Flexible graphite J Aramid with
Neoprene
Maximum Inlet Pressure/Temperature(1)
Valve Body Classification
Consistent with J CL150 and J CL300
pressure/temperature ratings per ASME B16.34. Also, Wafer and Lugged face-to-face dimensions are in
see figures 2 and 3 for additional information compliance with MSS SP68 and API 609 standards
NPS 30 through 48: J CL150/150 construction has through NPS 24. Double Flange valve bodies comply
CL150 rated pressure retaining parts and 150 psid with API 609 short face-to-face dimensions. Valve
rated trim bodies are designed for installation between ASME
B16.5 CL150 or CL300 raised-face flanges
Available Seal Configurations
Shutoff Classification. Per ANSI/FCI 70-2 and
Standard Constructions IEC 60534-4
See figure 4 and table 2
Standard Soft Seal: Bidirectional shutoff Class VI
Standard Construction Materials (bubble‐tight)
Valve Body and Disk: ASTM grades of J carbon steel, NOVEX Seal: Unidirectional shutoff Class IV (preferred
J stainless steel, J duplex, or J superduplex flow direction only(3)), Class VI optional (excluding
NPS 42 and 48)
Disk Coating: Phoenix III Seal: Bidirectional shutoff Class VI
Hardfacing options are available. Chrome plate is (bubble‐tight)
standard with NOVEX, Phoenix III, or Cryogenic seals Phoenix III Seal for Fire‐Tested Applications:
Unidirectional shutoff Class VI (reverse flow direction
Shaft: ASTM grade of J S17400 (17-4PH H1025 SST), only) (bubble‐tight). Fire Tested per API 607 Rev. 4.
J S20910, J S31803, or J S32760 Contact your Emerson sales office for more
Shaft Extension Lengths: information
High Temperature J Extensions are available but not
Flow Characteristic
required for temperatures less than 343_C (650_F),
J Optional 6 inches for temperatures from 343 to Modified equal percentage
538_C (650 to 1000_F), or J 12 inches for Flow Coefficients
temperatures above 538_C (1000_F)
Cryogenic J 914mm (36 in) from valve center line See table 1 and Fisher Catalog 12
Seal Ring: J PTFE, J S31600 (316 SST), J S21800, Noise Levels
J S31600/PTFE, J UHMWPE(4), or J CTFE(5). See Catalog 12 for sound pressure level prediction
‐continued‐
2
Product Bulletin
8532 Valve 51.6:8532
D101552X012 January 2023
Specifications (cont.)
Disk Rotation ENVIRO-SEAL Packing
This optional J PTFE or J graphite packing system
Clockwise to close provides improved sealing, guiding, and transmission
of loading force to control liquid and gas emissions.
Valve Dimensions and Approximate Weights See Bulletin 59.3:041 ENVIRO-SEAL Packing Systems
for Rotary Valves (D101638X012) for more
See figures 7, 8, 9, and 10 information.
1. The pressure/temperature limits in this bulletin (figures 2 and 3), and any application code or standard limitation, should not be exceeded.
2. PEEK stands for poly-ether-ether-ketone.
3. For optimum seal performance, the preferred valve orientation at shutoff is with the retaining ring downstream from the high pressure side of the valve.
4. UHMWPE stands for ultra high molecular weight polyethylene.
5. CTFE not recommended for fast cycling, less than 2 seconds. Contact your Emerson sales office for other seals available for fast cycling or tighter shutoff.
3
Product Bulletin
51.6:8532 8532 Valve
January 2023 D101552X012
FORWARD
FLOW
A7092
FACE SIDE OF DISK
Table 1. Flow Coefficients(1)(3) from valve surfaces. This sweeping action prevents
VALVE SIZE, MAX Cv (2), VALVE 90_ OPEN particle buildup on seal surfaces. However, the valve
NPS CL150/150 CL150 CL300 may be installed in either the forward or reverse flow
14 --- 6320 4550
direction.
16 --- 8600 5630
18 --- 11,050 8230 The standard soft seal offers bubble-tight, bidirectional
20 --- 13,850 9530 shutoff. To meet the performance requirements of
24 --- 21,500 12,510 many of today's fire-tested requirements, a Phoenix III
30 40,500 33,900 23,800 valve must be installed in the preferred valve
36 60,600 50,500 36,800
42 79,800 72,700 57,100
orientation. Both the NOVEX and cryogenic seals are
48 106,000 92,600 62,200 uni-directional and should be installed with the shaft
1. To obtain the flow coefficient Kv in terms of cubic meters per hour at one kilogram upstream of the seal.
force per square centimeter differential pressure across the valve, using the following
multiplier: Kv = 0.856 Cv .
2. Measured in gallons per minutes at 1 psi differential pressure across the valve. Unique operating conditions may require a specific
3. See Catalog 12 for a complete listing of flow coefficients.
combination of actuator motion. To satisfy unique
operating requirements, the valve and actuator can be
assembled in eight ways, providing for actuator
motion and open disk position. For assistance in
Installation selecting the appropriate combination of actuator
action and open valve position, consult your Emerson
Recommended installation for the 8532 valve is with sales office.
the shaft horizontal in a normal-flow direction.
Horizontal installation will enhance valve performance Dimensions and weights are shown in figures 7, 8, 9,
because process fluid flow will sweep entrained solids and 10.
4
Product Bulletin
8532 Valve 51.6:8532
D101552X012 January 2023
Figure 2. Maximum Pressure/Temperature Ratings for Soft Seal, NOVEX Seal and Phoenix III Seal, CL150 and CL300
Note
Because
1 of potential erosive effects and premature seal failure that can occur, throttling PTFE seals at differential pressures greater than 300 psid at disk angles less
than 20° open is not recommended.
Temperature
2 limitations do not account for the additional limitations imposed by the backup O-ring used with this seal. To determine the effective temperature limi
tation of the appropriate seal, backup O-ring combination, refer to table 1.
5
Product Bulletin
51.6:8532 8532 Valve
January 2023 D101552X012
Figure 3. Maximum Pressure/Temperature Ratings for Cryogenic Seal, CL150 and CL300
B2336
CL150 CRYOGENIC SEAL CL300 CRYOGENIC SEAL
GRAPHITE
BACKUP BODY GASKET BODY
O-RING
SEAL RING
RETAINING
RETAINING
RING
RING
METAL
NORMAL SEAL RING
FLOW DIRECTION NORMAL
VALVE DISK (REVERSE FLOW) VALVE DISK
FLOW
PTFE OR UHMWPE SOFT NOVEX METAL SEAL DIRECTION
SEAL WITH BACKUP O-RING (REVERSE
FLOW)
GRAPHITE BODY
GASKET
BACKUP
O-RING
METAL
SEAL RING
RESILIENT
INSERT
VALVE DISK NORMAL
FLOW DIRECTION
B2313-2
PHOENIX III (REVERSE FLOW)
FIRE SAFE SEAL
6
Product Bulletin
8532 Valve 51.6:8532
D101552X012 January 2023
GASKET RETAINER
PACKING FOLLOWER
GASKET
A7093
VALVE BODY
HEX NUT
STUD
PACKING
SHAFT
FLANGE
ANTI-EXTRUSION
RING PACKING
PACKING SET
SHAFT SHOULDER
FOLLOWER
7
Product Bulletin
51.6:8532 8532 Valve
January 2023 D101552X012
8
Product Bulletin
8532 Valve 51.6:8532
D101552X012 January 2023
9
Product Bulletin
51.6:8532 8532 Valve
January 2023 D101552X012
Figure 7. Dimensions and Weights, Wafer Style Valves (also see table 3)
C0729-1
10
Product Bulletin
8532 Valve 51.6:8532
D101552X012 January 2023
11
Product Bulletin
51.6:8532 8532 Valve
January 2023 D101552X012
C0730-1
12
Product Bulletin
8532 Valve 51.6:8532
D101552X012 January 2023
Figure 9. Dimensions and Weights, Double Flange Valves (also see table 5)
A
G K D B
S
T
W
X U
13
Product Bulletin
51.6:8532 8532 Valve
January 2023 D101552X012
14
Product Bulletin
8532 Valve 51.6:8532
D101552X012 January 2023
Figure 10. Dimensions, Optional Keyed Shaft Valves (also see table 6)
E
L
S
15
Product Bulletin
51.6:8532 8532 Valve
January 2023 D101552X012
Neither Emerson, Emerson Automation Solutions, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance
of any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.
Fisher and ENVIRO-SEAL are marks owned by one of the companies in the Emerson Automation Solutions business unit of Emerson Electric Co. Emerson
Automation Solutions, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the property of their
respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not
to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are
governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such
products at any time without notice.
Emerson Automation Solutions
Marshalltown, Iowa 50158 USA
Sorocaba, 18087 Brazil
Cernay, 68700 France
Dubai, United Arab Emirates
Singapore 128461 Singapore
www.Fisher.com
E
161991, 2023 Fisher Controls International LLC. All rights reserved.