ROHINI COLLEGE OF ENGINEERING & TECHNOLOGY

2.4 THE CELLULAR CONCEPT

The cellular concept was a major breakthrough in solving the problem of spectral congestion
and user capacity.
It offered very high capacity in a limited spectrum allocation without any major
technological changes.
The cellular concept is a system-level idea which calls for replacing a single, high power
transmitter (large cell) with many low power transmitters (small cells),each providing
coverage to only a small portion of the service area.
Each base station is allocated a portion of the total number of channels available to the entire
system, and nearby base stations are assigned different groups of
channels so that all the available channels are assigned to a relatively small number of
neighboring base stations.
Neighboring base stations are assigned different groups of channels so that the interference
between base stations (and the mobile users under their control) is minimized.
As the demand for service increases (i.e., as more channels are needed within a particular
market), the number of base stations may be increased (along with a corresponding decrease
in transmitter power to avoid added interference), thereby providing additional radio
capacity with no additional increase in radio spectrum.
This fundamental principle is the foundation for all modern wireless communication
systems, since it enables a fixed number of channels to serve an arbitrarily large number of
subscribers by reusing the channels throughout the coverage region.

Frequency Reuse

Cellular radio systems rely on an intelligent allocation and reuse of channels throughout a
coverage region.
Each cellular base station is allocated a group of radio channels to be used within a small
geographic area called a cell.
Base stations in adjacent cells are assigned channel groups which contain completely
different channels than neighboring cells. The base station antennas are designed to achieve
the desired coverage within the particular cell.

EC8652 WIRELESS COMMUNICATION

By limiting the coverage area to within the boundaries of a cell, the same group of channels
may be used to cover different cells that are separated from one another by distances large
enough to keep interference levels within tolerable limits.
The design process of selecting and allocating channel groups for all of the cellular base
stations within a system is called frequency reuse or frequency planning.

Fig 2.4.1: Frequency reuse concept

[Source : “Wireless communications” by Theodore S. Rappaport,Page-27]

The hexagonal cell shape shown in figure 2.4.1. is conceptual and is a simplistic model of
the radio coverage for each base station, but it has been universally adopted since the
hexagon permits easy and manageable analysis of a cellular system.
The actual radio coverage of a cell is known as the footprint and is determined from field
measurements or propagation prediction models.
Cells with the same letter use the same set of frequencies.
A cell cluster is outlined in bold and replicated over the coverage area.
In this example, the cluster size, N, is equal to seven, and the frequency reuse factor is 1/7
since each cell contains one-seventh of the total number of available channels.
Normally, omni directional antennas are used in center-excited cells and sectored directional
antennas are used in corner-excited cells.
EC8652 WIRELESS COMMUNICATION
 ROHINI COLLEGE OF ENGINEERING & TECHNOLOGY

Practical considerations usually do not allow base stations to be placed exactly as they
appear in the hexagonal layout.
To understand the frequency reuse concept, consider a cellular system which has a total of
S duplex channels available for use.
If each cell is allocated a group of k channels (k< S), and if the S channels are divided among
N cells into unique and disjoint channel groups which each have the same number of
channels, the total number of available radio channels can be expressed as
S=kN
The N cells which collectively use the complete set of available frequencies is called a
cluster.
If a cluster is replicated M times within the system, the total number of duplex channels,C,
can be used as a measure of capacity and is given by
C=MkN=MS
The capacity of a cellular system is directly proportional to the number of times a cluster is
replicated in a fixed service area.
The factor N is called the cluster size and is typically equal to 4, 7, or 12. If the cluster size
Nis reduced while the cell size is kept constant, more clusters are required to cover a given
area, and hence more capacity (a larger value of C) is achieved.
The value for N is a function of how much interference a mobile or base station can tolerate
while maintaining a sufficient quality of communications.

From a design viewpoint, the smallest possible value of N is desirable in order to maximize
capacity over a given coverage area.

where i and j are non-negative integers.

To find the nearest co-channel neighbors of a particular cell, one must do the following:

(1) move icells along any chain of hexagons as in figure 2.4.2 and then
(2) turn 60 degrees counter-clockwise and move j cells.

EC8652 WIRELESS COMMUNICATION

19- cell reuse example(N=19)

Fig 2.4.2: Method of locating co-channel cells in a cellular system.

Method of locating co-channel cells in a cellular system is shown above. In this

_________________________________________________

EC8652 WIRELESS COMMUNICATION