Western University

Scholarship@Western
Electronic hesis and Dissertation Repository

May 2015

Coniguration, Programming, Implementation, and

Evaluation of Distributed Control System for a
Process Simulator
Ximing Liu
he University of Western Ontario

Supervisor
Jin Jiang
he University of Western Ontario

Graduate Program in Electrical and Computer Engineering

A thesis submited in partial fulillment of the requirements for the degree in Master of Engineering Science

© Ximing Liu 2015

Follow this and additional works at: htp://ir.lib.uwo.ca/etd

Part of the Controls and Control heory Commons

Recommended Citation
Liu, Ximing, "Coniguration, Programming, Implementation, and Evaluation of Distributed Control System for a Process Simulator"
(2015). Electronic hesis and Dissertation Repository. Paper 2801.

his Dissertation/hesis is brought to you for free and open access by Scholarship@Western. It has been accepted for inclusion in Electronic hesis
and Dissertation Repository by an authorized administrator of Scholarship@Western. For more information, please contact [email protected].
CONFIGURATION, PROGRAMMING, IMPLEMENTATION

AND EVALUATION OF DISTRIBUTED CONTROL SYSTEM

FOR A PROCESS SIMULATOR

(Thesis format: Monograph)

by

Ximing Liu

Graduate Program in
Electrical and Computer Engineering

A thesis submitted in partial fulfilment

of the requirements for the degree of
Master of Engineering Science

School of Graduate and Postdoctoral Studies

The University of Western Ontario
London, Ontario, Canada

© Ximing Liu, 2015

 Abstract

A common industrial distributed control system (DCS), DeltaV, is configured and

programmed to control and monitor the Nuclear Process Control Test Facility (NPCTF). A
cabinet which holds the hardware of the DelatV DCS system, including programmable logic
controller (PLC), power supplies, input/output (I/O) cards, terminals, and relays are
configured and wired to field devices of NPCTF. A workstation and HMI screen are
configured and setup.

To implement the main functions of NPCTF in the DelatV system, the programming
architecture is designed in the DelatV system. The main control and monitoring functions of
NPCTF are programmed using industrial languages of Function Block Diagram (FBD) and
Sequential Function Chart (SFC) by IEC61113-3. Safety interlocks are added in the program
to protect the NPCTF devices from damage. A HMI is developed to operate and monitor the
NPCTF. Through the HMI, the operator can monitor the parameters of process of NPCTF,
operate the NPCTF, change parameters of the controller, and force the devices.

The process model of SG (Steam Generator) Tank level control is developed using the
MATLAB System Identification tool. The model is taken as an example to demonstrate the
process of analysis and design the controller of process control. PID is used as the controller
algorithm.

The main control and monitoring functions of NPCTF in the DeltaV system are
commissioned, tested and evaluated. The evaluation results conclude that the DelatV DCS
system can control the NPCTF to achieve the main functions of the NPCTF.

Keywords: Distributed Control System (DCS), process control, Programmable Logic

Controller (PLC), Proportional-Integral-Derivative (PID) Control

ii
 Acknowledgments

I would like to express my appreciation and thanks to my advisor Dr. Jin Jiang, whose
expertise, understanding and patience added considerably to my graduate experience. I
appreciate his thorough guidance through my research and graduate life. I must thank the
members of the examining board for taking time from their busy schedules to provide
valuable feedback.

I would also like to thank Dr. Xinhong Huang for her encouragement, patience and assistance
in writing this thesis and Dr. Ataul Bari for his support in this research, and for ordering the
devices for it.

I am also thankful to all the members of the Control Instrumentation and Electrical Systems
research group of the University of Western Ontario, in particular Drew Rankin and Jianping
Ma, for their support in various aspects of my research work. Our debates, and exchanges of
knowledge and skills throughout my graduate program have enriched my graduate
experience.

I give special thanks to my wife. Words cannot express how grateful I am to her for all her
sacrifices. Without her support, encouragement, and love I would not have returned to
academia and completed this thesis.

I also acknowledge that this research would not have been possible without the financial
support of the Natural Sciences and Engineering Research Council of Canada (NSERC), the
University Network of Excellence in Nuclear Engineering (UNENE), the University of
Western Ontario Graduate Studies, the Department of Electrical and Computer Engineering
at the University of Western Ontario (Teaching Assistantships, Graduate Research
Scholarships). I express my gratitude to those organizations.

iii
 Table of Contents
Abstract…………………..……………………………………………….……….….…..ii

Acknowledgements............................................................................................................iii

Table of Contents…………………………………………………………...…....……....iv

List of Tables………………………………………………………………………........viii

List of Figures………………………………………………………………………….....ix

Abbreviations and Nomenclature……………………..………………….……….……xv

1 Introduction ................................................................................................................. 1

1.1 Background .......................................................................................................... 1

1.1.1 CANDU Nuclear Power Plant (NPP) ........................................................ 1

1.1.2 Distributed Control System (DCS) ............................................................ 3

1.1.3 Programmable logic controller (PLC) ....................................................... 6

1.2 Motivations........................................................................................................... 8

1.3 Objectives and Scope ........................................................................................... 9

1.4 Contributions ........................................................................................................ 9

1.5 Organization of the Thesis ................................................................................. 10

2 Control System Requirements for Nuclear Process Control Test Faciliy ........... 12

2.1 System Introduction ........................................................................................... 12

2.2 Process Control................................................................................................... 15

2.3 Sequence Control ............................................................................................... 16

2.4 Safety Systems ................................................................................................... 17

2.4.1 Shutdown System Number 1 (SDS1) ...................................................... 18

2.4.2 Shutdown System Number 2 (SDS2) ...................................................... 19

iv
 2.4.3 Emergency Core Cooling (ECC) ............................................................. 20

2.5 Operation Modes ................................................................................................ 21

2.5.1 Normal mode of operation ....................................................................... 22

2.5.2 Solid mode of operation ........................................................................... 24

2.5.3 Open mode of operation .......................................................................... 26

2.6 Summary…………………………………………………………….…………27

3 Control System Design for NPCTF using DeltaV DCS ......................................... 28

3.1 Introduction to DeltaV DCS system ................................................................... 28

3.2 System Configuration and Connection............................................................... 29

3.2.1 DeltaV cabinet configuration ................................................................... 29

3.2.2 I/O card wiring diagrams ......................................................................... 31

3.2.3 Connection to field devices...................................................................... 35

3.3 Programming Architecture Design ..................................................................... 39

3.4 DCS Programming Languages (IEC 61131-3) .................................................. 42

3.4.1 Function block diagram (FBD) ................................................................ 43

3.4.2 Sequential Function Chart (SFC) ............................................................. 45

3.5 Programming Algorithms for Modules .............................................................. 46

3.6 Human Machine Interface (HMI) Configuration: Graphics and Faceplates ...... 47

3.7 Summary………………………………………………………………………..51

4 Process Controller Design in DeltaV DCS .............................................................. 52

4.1 Development of Control Strategies .................................................................... 52

4.1.1 Proportional-integral-derivative (PID) algorithm .................................... 53

4.1.2 Control loops with two actuators ............................................................. 55

v
 4.2 Controller Analysis and Design for Steam Generator Level Control ................ 57

4.2.1 Process model .......................................................................................... 57

4.2.2 Stable analysis.......................................................................................... 61

4.2.3 Controller parameters tuning using simpe-IMC method ......................... 62

4.2.4 Comparison of tuning results in MATLAB and on NPCTF .................... 65

4.3 Empirical Tuning Methods for Process Loops ................................................... 67

4.4 Summary………………………………………………………………………..70

5 Evaluation and Testing of the DCS operated NPCTF .......................................... 71

5.1 Process Control................................................................................................... 71

5.1.1 Evaluation methods.................................................................................. 71

5.1.2 Primary water flow control ...................................................................... 73

5.1.3 Water heater control................................................................................. 75

5.1.4 HX Tank pressure control ........................................................................ 77

5.1.5 Pressurizer pressure control ..................................................................... 80

5.1.6 Pressurizer water level control ................................................................. 83

5.1.7 Upper Tank level control ......................................................................... 85

5.1.8 Water inventory pressure control ............................................................. 87

5.2 Sequence Control ............................................................................................... 89

5.3 Safety Systems Evaluation ................................................................................. 91

5.3.1 Shut-down System Number 1 (SDS1) ..................................................... 91

5.3.2 Shut-down System Number 2 (SDS2) ..................................................... 94

5.3.3 Emergency Core Cooling (ECC) ............................................................. 96

5.4 Operation Modes Evaluation .............................................................................. 99

vi
 5.4.1 Normal mode evaluation .......................................................................... 99

5.4.2 Solid mode evaluation ........................................................................... 100

5.4.3 Open mode evaluation ........................................................................... 101

5.5 Summary………………………………………………………………………102

6 Conclusions .............................................................................................................. 103

6.1 Summary of Contributions ............................................................................... 104

6.2 Suggestions for Future Work ........................................................................... 105

References ....................................................................................................................... 107

Appendices ...................................................................................................................... 111

A List of I/O (input/output) signals ..................................................................... 111

B Process control loops I/O ................................................................................. 118

C Safety Systems Logic Diagrams ...................................................................... 120

D Programs of NPCTF in DeltaV DCS system .................................................. 121

Curriculum Vitae……………………………………………………………………....170

vii
 List of Tables

4.1 Control loops with two actuators ............................................................................... 57

4.2 Overshoot and rise time from simulation of MATLAB and NPCTF experiments.... 67

4.3 PID parameters of process controller tuned by empirical method ............................. 70

A.1 List of I/O signals ..................................................................................................... 111

B.1 Process control loops I/O ......................................................................................... 118

viii
 List of Figures

1.1 Simplified block diagram of main process and control systems of a CANDU NPP... 2

1.2 Heat transport system inventory control………………………………….…………. 3

1.3 Typical DCS system structure ……………………………………………………….6

1.4 PLC architecture…………………………………………………………………….. 8

2.1 Physical system of NPCTF ........................................................................................ 13

2.2 P&ID Diagram for NPCTF ........................................................................................ 14

2.3 P&ID Diagram for NPCTF process variables ........................................................... 16

2.4 Logical diagram for start-up procedure ..................................................................... 17

2.5 Logic function diagram of relays ............................................................................... 19

2.6 2oo3 logic function diagram of SDS1 ....................................................................... 19

2.7 Logic function diagram of SDS2 ............................................................................... 20

2.8 Logic function diagram of ECC ................................................................................. 20

2.9 P&I diagram of NPCTF to show ECC ....................................................................... 21

2.10 P&ID diagram of partial NPCTF in Normal mode .................................................... 23

2.11 Logic function diagram of Normal mode .................................................................. 24

2.12 P&ID diagram of partial NPCTF in Solid mode ....................................................... 25

2.13 Logic function diagram of Solid mode ...................................................................... 26

ix
2.14 P&ID diagram of partial NPCTF in Open mode ....................................................... 27

3.1 DeltaV system overview diagram .............................................................................. 28

3.2 Device schematic diagram in DeltaV cabinet ............................................................ 31

3.3 AI card wiring ............................................................................................................ 32

3.4 AO card wiring .......................................................................................................... 33

3.5 DI card wiring diagram .............................................................................................. 33

3.6 DO card wiring diagram ........................................................................................... 34

3.7 DO signal intermediate circuit ................................................................................... 35

3.8 Schematic diagram of wiring system ......................................................................... 36

3.9 DeltaV server and screen ........................................................................................... 37

3.10 DeltaV cabinet ........................................................................................................... 37

3.11 Wiring of DCS cabinet............................................................................................... 38

3.12 Field devices of NPCTF............................................................................................. 38

3.13 Programming architecture schematic diagram of typical DeltaV system .................. 39

3.14 Programming architecture schematic diagram of NPCTF ......................................... 40

3.15 Programming architecture diagram of NPCTF .......................................................... 41

3.16 Individual function block ........................................................................................... 43

3.17 FBD Network ............................................................................................................. 44

x
3.18 SFC network .............................................................................................................. 45

3.19 Programming architecture of NPCTF ........................................................................ 47

3.20 HMI of NPCTF .......................................................................................................... 49

3.21 Typical faceplate ........................................................................................................ 50

3.22 Current trend of controller parameters ....................................................................... 50

3.23 Controller tuning parameters ..................................................................................... 51

4.1 Process control diagram ............................................................................................. 52

4.2 Diagram of water inventory control process .............................................................. 56

4.3 Diagram for system identification procedure ............................................................ 59

4.4 Diagram of SG HX Tank level control ...................................................................... 60

4.5 Input and output curve from experiment data ............................................................ 61

4.6 Block diagram of closed-loop .................................................................................... 62

4.7 Gain and phase margins on a Bode plot..................................................................... 65

4.8 Function block diagram of close loop control ........................................................... 66

4.9 SG Tank level responses from Simulink ................................................................... 66

4.10 SG Tank level responses from NPCTF experiment ................................................... 67

4.11 Effect of changing Kc ................................................................................................. 68

4.12 Effect of changing Ti ................................................................................................. 69

xi
5.1 Performance specifications in time domain ............................................................... 72

5.2 Primary water flow performance ............................................................................... 73

5.3 Performance characteristics of step response of decrease primary water flow ......... 74

5.4 Performance characteristics of step response of increase primary water flow .......... 74

5.5 Heater outlet temperature performances .................................................................... 75

5.6 Performance characteristics of step response of decrease heater outlet temperature 76

5.7 Performance characteristics of step response of heater outlet temperature ............... 77

5.8 HX Tank pressure performances ............................................................................... 78

5.9 Performance characteristics of step response of HX tank pressure (0psig-2psig) ..... 79

5.10 Performance characteristics of step response of HX tank pressure (2psig-3psig) ..... 79

5.11 Performance characteristics of step response of HX tank pressure (3psig-4psig) ..... 80

5.12 Pressurizer pressure control performances ................................................................ 81

5.13 Performance characteristics of step response of pressurizer pressure (2psig-3psig) . 81

5.14 Performance characteristics of step response of pressurizer pressure (3psig-4psig) . 82

5.15 Performance characteristics of step response of pressurizer pressure (4psig-5psig) . 82

5.16 Pressurizer water level control performances ............................................................ 83

5.17 Performance characteristics of step response of pressurizer level (42%-45%) ......... 84

5.18 Performance characteristics of step response of pressurizer level (45%-50%) ......... 84

xii
5.19 Upper Tank level control performances .................................................................... 85

5.20 Upper Tank level step response from 30% to 35%.................................................... 86

5.21 Upper Tank level step response from 35% to 40%.................................................... 86

5.22 Upper Tank level step response from 40% to 45%.................................................... 87

5.23 Primary water pressure P1 step response ................................................................... 88

5.24 Primary water pressure P1 step response from 3 psig to 5 psig................................. 89

5.25 Tanks level change during start-up ............................................................................ 90

5.26 NPCTF system diagram during start-up .................................................................... 91

5.27 T2 average curves for SDS1 ...................................................................................... 92

5.28 NPCTF system diagram for SDS1 ............................................................................. 93

5.29 Alarm of SDS1 ........................................................................................................... 93

5.30 Primary water pressure P1 curve for SDS2 ............................................................... 94

5.31 NPCTF system diagram for SDS2 ............................................................................. 95

5.32 Alarm of SDS2 ........................................................................................................... 95

5.33 Primary water pressure P1 for ECC ........................................................................... 97

5.34 NPCTF system diagram for ECC .............................................................................. 98

5.35 Alarm of ECC and SDS2 ........................................................................................... 98

5.36 NPCTF system diagram during “Close With Pressurizer Mode” .............................. 99

xiii
5.37 NPCTF system diagram during “Close Without Pressurizer Mode”....................... 100

5.38 NPCTF system diagram during “Open Mode” ........................................................ 101

xiv
 Abbreviations and Nomenclature

Abbreviations

2oo3 Two-out-of-three voting

A/D Analog to Digital

AECL Atomic Energy of Canada Limited

AI Analog Input

AO Analog Output

CANDU Canadian Deuterium Uranium

CB Circuit Breaker

CPU Central Processing Unit

CV Control Valve

D/A Digital to Analog

DCS Distributed Control System

DDC Direct-digital Control

DI Digital Input

DO Digital Output

D2O Deuterium Oxide, Heavy Water

ECC Emergency Core Cooling

xv
FBD Function Block Diagram

FOPDT First-order-plus-dead-time

FPE Final Prediction Error

HMI Human Machine Interface

I&C Instrumentation and Control

ICI Imperial Chemical Industries

IL Instruction List

IMC Internal Model Control

I/O Input / Output

LD Ladder Diagram

LOCA Loss-of-coolant Accident

mA milli-ampere

MSE Mean Square Error

MWe Megawatt Electrical

NC Normal Close

NO Normal Open

NPCTF Nuclear Power Control Test Facility

NPP Nuclear Power Plant

xvi
OLE Object Linking and Embedding

OPC OLE for Process Control

PEM Prediction Error Method

PID Proportional-integral-derivative

PLC Programmable Logic Controller

P&ID Piping and Instrumentation Diagram

PV Process variable

SDS1 Shutdown System Number 1

SDS2 Shutdown System Number 2

SFC Sequential Function Chart

SG Steam Generator

SIMC Simple Internal Model Control

SOPDT Second-order-plus-dead-time

SP Set-point

ST Structured Text

VDC Voltage Direct Current

xvii
Nomenclature

Kc controller gain

I integral time

Ts scan interval

D derivative time

Kp process gain

p time constant

θ process delay

c critical frequency

g gain cross frequency

xviii
 1

Chapter 1
Introduction
1.1 Background
1.1.1 CANDU Nuclear Power Plant (NPP)
The CANDU (Canadian Deuterium Uranium) is a Canadian invented, pressurized heavy
water reactor. It is characterized by heavy water as coolant and moderator, and use
natural uranium as fuel [1]. CANDU NPPs (nuclear power plants) are developed and
maintained by AECL (Atomic Energy of Canada Limited) [2] [3]. There are 22 units of
CANDU reactors with a capacity of 15,358 MWe. It provides approximately 15% of
Canada’s total electricity needs (over 50% in Ontario, Canada) [4]. CANDU reactors
have been installed in seven countries [5].

The main energy exchange process in the CANDU nuclear power plant (NPP) is
illustrated in Figure 1.1. The heavy water (D2O) of the heat transport system is pumped to
the reactor to be heated and becomes heated heavy water. The heated heavy water is then
transported to steam a generator. Inside the steam generator, the heated heavy water heats
the feed-water to saturated steam and becomes cooled heavy water. The cooled heavy
water feeds back to the reactor. The saturated steam is fed to drive the turbine and
generator to produce power. Thereafter, steam becomes water and is pumped back to the
steam generator.

The process control system of CANDU NPP mainly consists of reactor regular system,
pressure and inventory control system, steam generator pressure and level control system,
and turbine control system. The reactor regulator system adjusts the reactivity of the
reactor and, thus, the power of the reactor. The pressure and inventory control system
regulates the pressure and inventory of the coolant in the heat transport system. The
steam generator pressure and level control system controls the pressure and level of the
 2

steam generator. The turbine control system controls the flow or pressure of the main
steam via turbine governors.

Reactor Heat Transport Steam Generator

Turbine
Regulator Pressure and Pressure and
Controller
System Inventory Control Level Control

Heat Steam
Reactor Turbine Generator
Transport Generator

Condenser

Moderator
Feedwater
Containment

Figure 1.1 Simplified block diagram of main process and control systems of a CANDU NPP

The heat transport system has two operation modes: Normal mode and Solid mode.
Under Normal operating mode, the pressurizer keeps the pressure of the heat transport
system while the feed and bleed system controls the inventory through pressurizer level,
as shown in Figure 1.2. Under the Solid operating mode, the pressurizer is isolated.
Instead, the feed and bleed system controls both pressure and inventory, as shown in
Figure 1.2.
 3

Heat transport system

inventory control
Normal mode

Heat transport system

inventory control
Solid mode

Feed
valve

Heat
transport
system Pressure
Pressurizer
level
Bleed
valve

Figure 1.2 Heat transport system inventory control [6]

The reactor safety system performs the functions necessary to maintain the plant in safe
conditions. SDS1 (Shutdown System Number 1), SDS2 (Shutdown System Number 2),
and ECC (Emergency Core Cooling) are three main reactor safety systems. SDS1 and
SDS2 are two shutdown systems that shut down the reactor for safety reasons. SDS1
consists of mechanical shutdown rods while SDS2 injects a gadolinium nitrate solution
into the moderator. These two shutdown systems are independent, and either of them can
shut down the reactor and maintain the shut down for all design basis events. Emergency
Core Cooling system supplies coolant to the reactor in the event of a loss-of-coolant
accident (LOCA).

1.1.2 Distributed Control System (DCS)

To study the dynamic properties of CANDU NPP, a physical component known as
Nuclear Power Control Test Facility (NPCTF) has been constructed in the CIES lab of
the University of Western Ontario. In this research, a DCS system is developed to
implement its functions.
 4

A Distributed control system is a computer based control system of an industry process

where its elements are distributed through different places [7] [49].

In the 1950’s, plants used large, local pneumatic controllers; the computers could only be
used for supervisory tasks. Many companies started the research to determine if
computers could be used for process control.

In the 1960s, the development of electronic integrated circuits led to the development of
micro-computers [8]. In 1962, an Argus computer developed by Ferranti Ltd. replaced a
complete analog control system in an ammonia/soda plant by a British chemistry
company, Imperial Chemical Industries (ICI). It is a direct-digital control (DDC)
computer and is expensive; however, it is still cheaper than the relay based control
system [9].

The development of computer technology, which is faster, cheaper and more reliable,
incubated the first distributed control system, TDC2000, and was introduced by
Honeywell in 1975 [10] [11]. However, this DCS was not suitable for discrete and batch
applications until the incorporating of PLC with DCS [12].

The further advances in computer hardware and software technology in 1980s caused the
DCSs to expand its function beyond process control. It facilitated the production, such as
process modeling, process accounting, expert system, and production planning and
dispatch. Another feature of DCS during this period was that DCSs were shifted from
proprietary systems to open systems to accommodate third party software. UNIX, one of
the operating systems, was a popular choice for operating system of DCS [13].

In the 1990s, Microsoft entered the related software field. The operating system of DCS
was moved from a UNIX to Windows environment [14]. OLE for process control (OPC)
technology was developed for DCS systems. OPC was only available on MS windows
and is now a de facto industry connectivity standard. It provides the “plug and play”
solution to the problem of integrating a device to the DCS [15]. Microsoft application
 5

tools Visual Basic and Visual C++ coupled with Active tools made complex and highly
specialized applications affordable for users.

Right now, DCS has been applied extensively in process control of different industries:
chemical plants, petrochemical industries and refines, power plant systems, nuclear
power plants, environmental control systems, water management systems, oil refining
plants, metallurgical process plants, and pharmaceutical manufacturing [11].

A nuclear power plant is a complex system. The distribute control system can perform
complex tasks and, thus, has been applied to process control in NPP [16] [17].

A typical DCS system structure includes devices in a control and supervisory level, as
shown in Figure 1.3. The control level collects the data from devices in the field which
are grouped with the name of the field level, does calculation and sends the results to
control the field devices. It includes a controller, such as PLC, IO cards, and
communication modules. The supervisory level includes operator station through human
machine interface (HMI) and an engineer station. Operators operate and monitor the
process through HMI. The engineer station configures the control strategies, maintains
the system and tunes the controller. The field level includes different kinds of field
devices, such as transmitters, sensors, and actuators. Transmitters convert the process
variables to electric signals, such as 4-20mA, or digital signal which are sent to the
controller. Valves actuators convert the electric from controller to mechanical movement
to drive the valves.
 6

DCS

Supervisory
Level

Process Control
Level

Process

Field Level

Figure 1.3 Typical DCS system structure [18]

1.1.3 Programmable logic controller (PLC)

In the DCS system designed in this research, PLCs (programmable logic controllers) are
used as the control equipment.

Originally, the process was often controlled by relays where the control room was full of
relays, terminals blocks and wire. For the relay-based control system, significant changes
are required to expand the system and add more functions. Moreover, it is difficult to
conduct troubleshooting considering there are huge number of relays and wiring. In the
1960’s, engineers at GM proposed to develop a prototype to eliminate costly scrapping of
assembly-line relays during changeovers, and replace unreliable relays. In 1971, Allen
Bradly developed a new concept, Bulletin 1774 PLC, and named it “Programmable Logic
Controller” (PLC). From then on, the PLC terminology became the industrial standard.
Several improvements have been made for PLC since it was first developed [19].

In the early 1980s, the industrial processes became more complex and a single PLC could
not control the entire system. Therefore, PLC began to incorporate distributed control
functions so they could be linked much in the way that DCSs were linked [20] [21].
 7

During the 1990s, standardization and an open system enabled further improvement in
PLC development.

In the market, there are different sizes of configurations: Micro PLC with less than 100
I/O, Small PLC with 100 to 200 I/O, Medium with less than 1000 I/O and large PLC with
more than 1000 I/O.

PLC has been extensively applied in different industry areas. According to a recent
Control Engineering magazine poll, “The major applications for PLCs include machine
control (87%), process control (58%), motion control (40%), batch control (26%),
diagnostic (18%), and others (3%).” The results do not add up to 100% because a single
control system generally has multiple applications [19].

A typical PLC mainly consists of CPU (central processing unit), power supply, memory
unit, and I/O (input/output) system, as illustrated in Figure 1.4. Power supply converts the
power line voltages to those required by the PLC. It drives the central processing unit,
memory unit, and I/O signals. CPU is the central component of PLC. It performs
necessary tasks to fulfil PLC function, such as scanning, executing programs,
communicating with other devices, and performing self-diagnostics. The memory unit
stores the application program and PLC execution program. The control data from the
CPU and the process data from I/O modules are also temporarily stored in the memory
unit. I/O modules function as the interface between field devices and CPU. The input
signal gives the CPU real time status of process variables. These signals could be either
analog or digital. Water flow is an example of analog signal and contact of relay is an
example of digital signal. They are presented to input cards as a varying voltage, or
current. Discrete and digital are common output categories. Discrete output can be sent to
turn on or turn off pilot lights, or open or close solenoid valves. Analog output can drive
signals to variable speed drives or I/P (current to air) converters and thus to control
valves. I/O systems are arranged in modules each of which contains a couple of I/O
points. These modules are plugged into the existing bus structure which carries
information back and forth between the I/O modules and central unit.
 8

Power
CPU Memory
supply

I/O system modules

Input Output
Devices Devices

Figure 1.4 PLC architecture

1.2 Motivations
DCS is applied in many industries [22], including different types of power stations.
Nuclear power plants are large, complex systems with potential risks [23]. An accident
could cause serious loss and impact on society. Therefore, any new control strategy or
function needs to be proved before applying it to a real nuclear power plant. In the past,
software which simulates the process of an NPP is the common method to test and prove
a new control strategy and function. However, process in the software is created by a
model which is always different from real plants. A system between software and a real
NPP will improve the validation process. Therefore, the NPCTF (Nuclear Process
Control Test Facility) is built in the CIES research lab at the University of Western
Ontario to simulate the main processes in a CANDU NPP and some other industrial
processes for I&C research. Even though it is not a real NPP, it is a real physical system.

In addition, this DCS operated NPP simulator can be used to train operators and students.
For students, it helps to create some concepts about CANDU NPP. For operators, it helps
to improve operating skills and emergency handling capabilities.

This research project is to design the DCS to control and operate the NPCTF. The
popular industrial DCS, Delta-V manufactured by Emerson, is used to design this system
[24].
 9

1.3 Objectives and Scope

As described in Section 1.2, it is important to develop a DCS system to implement the
functions of NPCTF. The following are the main objectives of this research:

1. Design and implementation of a DCS system using a DeltaV platform to control the
NPCTF.

2. Development of programs to implement the main functions of the NPCTF system

3. The process model of steam generator (SG) level control is developed and analyzed to
present the process control strategies design process.

4. Development of the operator interface to operate the NPCTF system.

5. Evaluation of the main functions of a DCS system to demonstrate the functionalities of

DeltaV DCS system to control NPCTF.

The goal of this work is to develop the DeltaV DCS system to control the NPCTF system,
and demonstrate the functionalities of NPCTF. Therefore, the following issues are out of
the scope of this research:

1. The specifications and the system design of NPCTF

1.4 Contributions
The following are the major contributions:

1. Control system development: A DCS system is developed to implement the process

control, sequence control, designed functions of safety systems and operation mode
selection on the NPCTF.

2. Programming: The control system of the NPCTF system is programmed in DeltaV

DCS system. HMI (Human Machine Interface) is developed to operate and monitor this
system.
 10

3. Model development: A Steam Generator (SG) level process model within operating
range of 36% to 44% is constructed using MATLAB and used to design the controller of
SG level control.

4. Tuning technique: The tuning technique is compared in MATLAB and on NPCTF

system.

5. Commissioning of the DCS: The control system of the NPCTF described in Chapter 2
are commissioned.

6. Evaluation of the DCS system: The control system described in chapter 2 are tested
and evaluated.

1.5 Organization of the Thesis

This thesis is organized as follows.

Chapter 2 introduces and describes the main functions to be implemented and achieved in
the NPCTF simulator through the DCS system. The functions are expressed in logic
diagrams.

Chapter 3 describes the DeltaV DCS platform used in this thesis, and how the DeltaV
DCS platform is used to program and implement the functions described in Chapter 2.
The hardware design and construction of the DCS system using the DeltaV platform are
discussed. The control architecture design of NPCTF is also presented. In addition, the
main programming languages used in this research are introduced. Furthermore, how to
use these two kinds of languages to program and implement the functions described in
Chapter 2 is also presented. In the end of Chapter 3, the details of developing HMI for
monitoring and operating the NPCTF are also discussed.

Since the process control is one of the main functions of the DCS system, Chapter 4
focuses on the development of process control. The control algorithm of PID, tuning
techniques and stability analysis standard used in the process control of this research are
 11

presented. Steam Generator (SG) level control is taken as an example to explain the
control process. In this example, the process model of Steam Generator level control is
created and two tuning techniques are compared in both MATLAB and NPCTF system.

Chapter 5 presents the results of the experiments and evaluations performed to

demonstrate the main functions of the DCS system for the NPCTF.

Chapter 6 concludes the research which summarizes the main contributions and discusses
potential future research.
 12

Chapter 2
Control System Requirements for Nuclear Process Control
Test Facility (NPCTF)
The simulator NPCTF (Nuclear Process Control Test Facility) has been built in the CIES
research lab at the University of Western Ontario. There are mainly four functions of this
simulator to be implemented in this research: process control, sequence control, designed
functions of safety systems, and operation modes. Process control is to control the
process variables of NPCTF. The main purpose of Sequence control is to fill in the pipes
and tanks in order for the system to be ready for operation. Safety system is used to
investigate the safety shut down functions: SDS1, SDS2, and ECC. Operation mode is to
make the NPCTF system run under different situations: Normal mode, Open mode and
Solid mode. These functions are programed and evaluated in this research.

2.1 System Introduction

The physical system of NPCTF is shown in Figure 2.1. As shown in Figure 2.1, Heater,
Pressurizer, HX tank, Turbine, and Generator are used to represent reactor, pressurizer,
steam generator, turbine, and generator in CANDU NPP, respectively. Its P&ID diagram
is shown in Figure 2.2. Before the system is to be controlled to desired status, the tanks
and pipes need to be filled up. As shown in Figure 2.1 and 2.2, Pump 2 feeds water
through valve CV-16 to fill in the pipes and tanks to make the system ready for control.
After the system is ready, an operator can select different operating modes to run the
system. In the sections 2.5, detail of different operating modes and their related
operations will be further described.
 13

Pressurizer Generator Turbine HX Tank

Upper Tank

Lower Tank Pump 2 Pump 1 Heater

Figure 2.1 Physical system of NPCTF

 14

Pressurizer HX Tank Turbine Generator

40psi air
supply Turbine-Generator

FV-5 P3
Display rpm
G

CV-9 Regulator CV-4

Regulator F2(VA)
Alarm/Display
P4 P2
CV-10
DAQ Pressurizer CV-21 CV-5 CV-8

To lower tank or Diffuser at

spill collection L3 tank bottom To lower tank or
Instrument L4 spill collection
signals
Chiller
Muffler

CV-12 CV-11 T6 HX behind

HX
tank
Upper L1
T7
T5
CV-34
F3
Tank Upper
tank CV-13
CV-25 T3
CV-14

CV-18
F4
prevention

Controller
Spill

A C
CV-19
CV-15 2-out-of-3
relays B A Legend:
CV-17 Po1 Sensors:
C B Coiled
C:Current; T:Temperature; L:Level;
pipe
Pneumatic P:Pressure; V:Vibration; F:Flow;
C3 gripper Po: Position; A: Acoustic
air Valves:
FV-2
CV-16 Gravity FV-3 CV: Control; FV: Fault injection;
drop rod SV: Reverse flow Stop;
Linear
motor Flow Lines:
assembly
Main water
SDS1 SDS2 Support water
Switch Switch Hidden water
P02
SV-1 LOCA water
C2
C1 Relief valve Natural flow
Air
Heater
SDS current
Lower C5
V1
CV-1
F1 P1 T1 T2-1/2/3
(Magnetic) Max outlet temp:
Tank Pump2 CV-3
Pump1 Bearing
fault
injection
CV-2 FV-1 65 Celsius CV-20 Copyright:
CIES laboratory
V2 The University of Western Ontario
SV-2 T4 London, Ontario, Canada
Lower
FV-6 Tank
Spill water collection tray

Pump 2 Pump 1 Heater

Figure 2.2 P&ID Diagram for NPCTF [25]
 15

2.2 Process Control

For the simulator, process control is the process that some process parameters of the
simulator are controlled to maintain the desired values. This simulator simulates 11
process control loops. These loops are designed to maintain the desired values of the
process parameters, including the primary water flow (F1), outlet temperature of the
Heater (T2), outlet temperature of the Chiller (T3) (HX outlet temperature), the HX Tank
level (L4) and pressure (P2), the Pressurizer pressure (P4) and level (L3), the Upper Tank
level (L1), water inventory pressure (P1), and air pressure (P3) and flow (F2). These
process variables are shown in Figure 2.3 with purple boxes. The methods of
manipulating these process variables are categorized into two types. The first type is
manipulated by one variable and the second type is manipulated by two variables. The
primary water flow (F1), outlet temperature of the Heater (T2), outlet temperature of the
Chiller (T3), the HX Tank level (L4) and pressure (P2), and air pressure (P3) and flow
(F2) are controlled through valve CV-1, the Heater current C2, valve CV-34, valve CV-
25, CV-21, CV-4, and CV-8, respectively. Each of the Pressurizer pressure (P4) and level
(L3), the Upper Tank level (L1), and water inventory pressure (P1) is controlled by two
valves. One is set as the main manipulated valve, while another has been fixed to remain
open to avoid the main valve being fully closed, but the process variable is still higher
than the desired value. Detail is shown in appendix B. All of these manipulated
parameters are shown in Figure 2.3 with brown boxes.
 16

Pressurizer HX Tank Turbine Generator

40psi air
supply Turbine-Generator

FV-5 P3
Display rpm
G
Regulator
CV-9 Regulator F2(VA) CV-4
Alarm/Display
P4 P2
CV-10
DAQ Pressurizer CV-21 CV-5 CV-8
To lower tank or Diffuser at
spill collection L3 tank bottom To lower tank or
Instrument
L4 spill collection
signals
Chiller
Muffler

CV-11 T6 HX behind
CV-12 tank HX

Upper L1
T7
T5
CV-34
F3
Tank Upper
tank CV-13 CV-25 T3
CV-14

CV-18
F4
prevention

Controller
Spill

A C
CV-19
CV-15 2-out-of-3
relays B A Legend:
CV-17 Po1 Sensors:
C B Coiled
C:Current; T:Temperature; L:Level;
pipe
Pneumatic P:Pressure; V:Vibration; F:Flow;
C3 gripper Po: Position; A: Acoustic
air Valves:
FV-2
CV-16 Gravity FV-3 CV: Control; FV: Fault injection;
drop rod SV: Reverse flow Stop;
Linear
motor Flow Lines:
assembly
Main water
SDS1 SDS2 Support water
Switch Switch Hidden water
SV-1 LOCA water
C2
C1 Relief valve Natural flow
Air
Heater
SDS current
Lower C5
V1
CV-1 F1 P1 T1 T2-1/2/3
Max outlet temp:
Tank Pump2 CV-3
Pump1 Bearing
fault
injection
CV-2 FV-1 65 Celsius CV-20 Copyright:
CIES laboratory
V2 The University of Western Ontario
SV-2 T4 London, Ontario, Canada
Lower
FV-6 Tank
Spill water collection tray

Pump 2 Pump 1 Heater

Figure 2.3 P&ID Diagram for NPCTF process variables

2.3 Sequence Control

Before the system starts, the tanks and pipes are required to be filled up and ready for
operation. The Start-up procedure is designed for this objective. When the START button
on the HMI is pressed, the pump begins to charge the Pressurizer, HX Tanks, and Upper
Tank in sequence. When the levels of tanks reach certain values, such as 30% to 60%, the
tanks are considered to be finished charging. In order to charge the related tanks, their
corresponding valves are open, and then close after finishing the charge, as shown in
Figure 2.4. For example, when charging the Pressurizer in the first step, valves CV-16,
CV-1, CV-2, CV-11, CV-14, and CV-16 are open to fill in the pipes and Pressurizer tank.
 17

Meanwhile, valves CV-3, CV-9, CV-12, CV-13, CV-15, CV-17, CV-18, CV-19, CV-20,
CV-21, and CV-25 are closed. Refer to system P&I, diagram Figure 2.2 for the detail of
these valves.

START

Start pump2
Close valves:CV-
Charging
3,9,12,13,15,17,18
Pressurizer
,19,20,21,25
Open valves:CV-
1,2,5,10,11,14,16

Charging Close valves:CV-

Complete 10,16

Charging Open valves:CV-

HX Tank 25

Charging Close valves:CV-

Complete 25

Charging Open valves:CV-

Upper Tank 17

Charging Close valves:CV-

Complete 17

Figure 2.4 Logical diagram for start-up procedure

2.4 Safety Systems

There are three main safety systems for this NPCTF: SDS1 (Shutdown System Number
1), SDS2 (Shutdown System Number 2), and ECC (Emergency Core Cooling). SDS1
and SDS2 are designed to prevent the potential damage of the NPCTF when key
operating parameters are out of the prescribed limit (see Appendix C for detail). If the
 18

cooling of the Heater is judged to be insufficient, the ECC system will act to cool the
Heater. In CANDU NPP, the safety systems are not designed in DCS system. However,
the safety systems take action to shut down reactor when the trip parameters are out of
limits, such as low pressurizer level. The trip parameters are measured with 2oo3 voting.
The simulator is used to simulate this protected process, for the system to take action in
response to the trip parameters and 2oo3 voting.

2.4.1 Shutdown System Number 1 (SDS1)

If there are urgent situations, the reactor needs to shut down. The function designed
simulates such urgent situations as HX Tank has abnormal water level (L4), and Heater
has high outlet temperature (T2) or no enough cooling flow (F3). If any of these
situations occur, the SDS1 signal is created and the heater is shut down. The logic is
shown in Figure 2.5. The design philosophy of Shut Down Systems (SDS1 and SDS2) is
based on triplicating the measurement of each signal, and initiating the protective action
when any of the three channels indicate that a trip condition exists. This is named as 2oo3
voting. In order to simulate the 2oo3 voting, relays A, B, and C are used to simulate
different channels. The logic is shown in Figure 2.6. If any two signals from channel A, B,
or C become true, the SDS1 signal is created to shut down the reactor, i.e. the Heater in
the simulator. In figure 2.5, in order to test the 2oo3 voting, parameters should be same.
For example, if relay A is activated due to “HTR T2 high”, relay B or C should be
activated by same parameters of “HTR T2 high” in order to activate SDS1 signal.
 19

HTR T2 high
Relay A

HX tank L4 low

HX tank L4 high

HTR T2 high
Relay B

HX tank L4 low

HX tank L4 high

HTR T2 high
Relay C

HX tank L4 low

HX tank L4 high

Figure 2.5 Logic function diagram of relays

Relay A

SDS1
Relay B Shut off HTR

Relay C

Figure 2.6 2oo3 logic function diagram of SDS1

2.4.2 Shutdown System Number 2 (SDS2)

SDS2 (Shutdown System Number 2) is an independent safety system. Three parameters
are selected to simulate the potential risk of the Heater. If any of these parameters is
 20

higher than the threshold, SDS2 will act and shut down the Heater. The logic is shown in
Figure 2.7.
HX tank L4 high

SDS2
HTR T2 high Shut off HTR

WTR P1 high

Figure 2.7 Logic function diagram of SDS2

2.4.3 Emergency Core Cooling (ECC)

The objective of an ECC system is to identify the potential risk of insufficient cooling of
the Heater and then act to stop this situation, i.e. stopping the heat source (Heater) and
feeding water from the Upper Tank to cool the Heater. As show in Figure 2.8, two
conditions are simulated as Heater insufficient cooling conditions. Either SDS1 or SDS2
is active and Pump 1 is shut down. When this insufficient cooling condition is met, the
ECC is created to shut off the heater and build the cooling circle of the Heater. As
indicated in Figure 2.9 as seen using a highlighted green line, cooling water from the
Upper Tank is fed to the Heater through the CV-19 and sent back to the Lower Tank.
Pump 2 then feeds the water to the Upper Tank again. During this circling process,
related valves are closed and opened to achieve the above functions, as shown in Figure
2.8.

1. Close CV-1 and CV-2

SDS1 ECCS

SDS2 Shut off HTR

Pump1 off
1. Close CV-15
2. Open CV-19,CV-20
3.Upper tank level controlled
by CV-17

Figure 2.8 Logic function diagram of ECC

 21

Pressurizer
HX Tank
Display

Alarm/Display
P4 P2

DAQ

Diffuser at
L3 tank bottom
Instrument
L4
signals
Chiller

CV-11 T6 HX behind
CV-12 tank HX

Upper L1
T7
T5
CV-34
F3
Tank Upper
tank CV-13 CV-25 T3
CV-14

CV-18
F4
prevention

Controller
Spill

A C
CV-15 CV-19 2-out-of-3
relays B A
CV-17 Po1
C B Coiled
pipe
Pneumatic
C3 gripper
air
FV-2
CV-16 Gravity FV-3
drop rod
Linear
motor
assembly

SDS1 SDS2
Switch Switch

SV-1
C2
C1 Relief valve

Heater
Lower C5
V1
CV-1 F1 P1 T1 T2-1/2/3
Max outlet temp:
Tank Pump2 CV-3
Pump1 Bearing
fault
injection
CV-2 FV-1 65 Celsius
CV-20
V2
SV-2 T4
Lower
FV-6 Tank
Spill water collection tray

Pump 2 Pump 1 Heater

Figure 2.9 P&I diagram of NPCTF to show ECC

2.5 Operation Modes

The Pressurizer is used to maintain the pressure of the heat transport system. This
operation mode is called Normal mode. However, under warm-up and cool-down
conditions, the Pressurizer is isolated. In this situation, the feed and bleed system is used
to maintain pressure and inventory of the heat transport system. This operation mode is
named Solid mode. In NPCTF, two operation modes are also designed to simulate both
 22

Normal mode and Solid mode. Moreover, an operation mode called Open mode is also
designed in NPCTF for general I&C related research purposes such as advanced control
theories, fault diagnostics, fault tolerance.

2.5.1 Normal mode of operation

Under Normal mode, the Pressurizer is used to maintain the primary water pressure (P1).
The primary water circling is shown in Figure 2.10 using a highlighted brown line; water
is fed by Pump 1 to Heater, cooled by Chiller and come back to inlet of Pump 1. As
shown in Figure 2.10, the pressure of the Pressuriser is controlled by CV-9 and CV-10
and shown using a purple line while the level is controlled by CV-16 and CV-12. The
related operation of valves and controllers in order to achieve above functions under
Normal mode are shown in Figure 2.11.
 23

Pressurizer
Display
HX Tank
Alarm/Display
P4 P2

DAQ Pressurizer
To lower tank or Diffuser at
spill collection L3 tank bottom
Instrument
L4
signals
Chiller

CV-11 T6 HX behind
CV-12 tank HX

Upper L1
T7
T5
CV-34
F3
Tank Upper
tank CV-13 CV-25 T3
CV-14

CV-18
F4
prevention

Controller
Spill

A C
CV-15 CV-19 2-out-of-3
relays B A
CV-17 Po1
C B Coiled
pipe
Pneumatic
C3 gripper
air
FV-2
CV-16 Gravity FV-3
drop rod
Linear
motor
assembly

SDS1 SDS2
Switch Switch

SV-1
C2
C1 Relief valve

Heater
Lower C5
V1
CV-1 F1 P1 T1 T2-1/2/3
Max outlet temp:
Tank Pump2 CV-3
Pump1 Bearing
fault
injection
CV-2 FV-1 65 Celsius CV-20
V2
SV-2 T4
Lower
FV-6 Tank
Spill water collection tray

Pump 2 Pump 1 Heater

Figure 2.10 P&ID diagram of partial NPCTF in Normal mode

 24

Close Water Loop Valves 1.Close CV-3, 13

with
2.Open CV-11, 14
Pressurizer(Normal)
Water Inventory and
Controllers Pressure(L3,P1)

1.L3 controlled by CV-12, CV-16

2.P1 is maintain by pressurizer

Pressurizer Pressure (P4)

P4 controlled by CV-9, CV-10

Figure 2.11 Logic function diagram of Normal mode

2.5.2 Solid mode of operation

Under Solid mode, the Pressurizer is isolated from water cycling. Primary water circling
is shown in Figure 2.12 with a highlighted brown line: water is fed by Pump 1 to Heater,
cooled by Chiller and come back to inlet of Pump1. As shown in Figure 2.12, the primary
water pressure (P1) is controlled by CV-13 and CV-16 and is shown using a purple line.
As shown in Figure 2.13, related valves and controllers are operated in order to achieve
the above functions under Solid mode.
 25

Pressurizer
Display
HX Tank
Alarm/Display
P4 P2

DAQ Pressurizer
To lower tank or Diffuser at
spill collection L3 tank bottom
Instrument
L4
signals
Chiller

CV-11 T6 HX behind
CV-12 tank HX

Upper L1
T7
T5
CV-34
F3
Tank Upper
tank CV-13 CV-25 T3
CV-14

CV-18
F4
prevention

Controller
Spill

A C
CV-15 CV-19 2-out-of-3
relays B A
CV-17 Po1
C B Coiled
pipe
Pneumatic
C3 gripper
air
FV-2
CV-16 Gravity FV-3
drop rod
Linear
motor
assembly

SDS1 SDS2
Switch Switch

SV-1
C2
C1 Relief valve

Heater
Lower C5
V1
CV-1 F1 P1 T1 T2-1/2/3
Max outlet temp:
Tank Pump2 CV-3
Pump1 Bearing
fault
injection
CV-2 FV-1 65 Celsius CV-20
V2
SV-2 T4
Lower
FV-6 Tank
Spill water collection tray

Pump 2 Pump 1 Heater

Figure 2.12 P&ID diagram of partial NPCTF in Solid mode

 26

Close Water Loop Valves 1.Close CV-3, 11,13

without
2.Open CV-14
Pressurizer(Solid)

Controller Primary water pressure (P1)

P1 controlled by CV-13, CV-16

Figure 2.13 Logic function diagram of Solid mode

2.5.3 Open mode of operation

The NPCTF in the CIES lab at the University of Western Ontario is designed, not only
for research of CANDU NPP, but for other general I&C related research as well. For
example, if the research is only to investigate the nonlinear and adaptive control
algorithm, and not related to CANDU, only a non-linear shaped Upper Tank and coiled
pipe are used for this research. Therefore, NPCTF can be operated under the Open mode.
Under Open mode, the Pressurizer is isolated from water cycling. Primary water circling
is shown in Figure 2.14 using a highlighted brown line: water is fed by Pump1 from the
Lower Tank via CV-3 to the Heater, cooled by the Chiller and then to Upper Tank. In
order to build this cycling, valves CV-3 and CV-13 are open and valves CV-11 are CV-
14 are close.
 27

Pressurizer
Display
HX Tank
Alarm/Display
P4 P2

DAQ Pressurizer
To lower tank or Diffuser at
spill collection L3 tank bottom
Instrument
L4
signals
Chiller

CV-11 T6 HX behind
CV-12 tank HX

Upper L1
T7
T5
CV-34
F3
Tank Upper
tank CV-13 CV-25 T3
CV-14

CV-18
F4
prevention

Controller
Spill

A C
CV-15 CV-19 2-out-of-3
relays B A
CV-17 Po1
C B Coiled
pipe
Pneumatic
C3 gripper
air
FV-2
CV-16 Gravity FV-3
drop rod
Linear
motor
assembly

SDS1 SDS2
Switch Switch

SV-1
C2
C1 Relief valve

Heater
Lower C5
V1
CV-1 F1 P1 T1 T2-1/2/3
Max outlet temp:
Tank Pump2 CV-3
Pump1 Bearing
fault
injection
CV-2 FV-1 65 Celsius CV-20
V2
SV-2 T4
Lower
FV-6 Tank
Spill water collection tray

Pump 2 Pump 1 Heater

Figure 2.14 P&ID diagram of partial NPCTF in Open mode

2.6 Summary
In summary, in this chapter, four main functions of this NPCTF, are explained and
described in detail. They are process control, sequence control, safety systems and
operation modes. The construction and design of the DCS system to implement these
functions are the topics of this research and are presented in Chapters 3 and 4. Their
evaluations are also the topic of this research and are discussed in Chapter 5.
 28

Chapter 3
Control System Design for NPCTF using DeltaV DCS
The Delta-V DCS system is one of the widely used DCS systems in industry [26] [27].
Therefore, DeltaV DCS system is selected to be used in this research to implement the
functions of NPCTF described in Chapter 2: process control, sequence control, safety
system, and operation modes.

3.1 Introduction to DeltaV DCS system

As a typical DCS system presented in Section 1.1.2, the DeltaV DCS system consists of
devices at the control and supervisory level. As illustrated in Figure 3.1, the DeltaV DCS
system in this research consists of workstation, two hubs, two system power supplies and
two controllers for redundancy, and I/O cards. While the other components are standard
design, I/O cards are different from project to project.

Workstation
Supervisory
Level

Primary Control Network

Primary Hub
Secondary Control Network
Secondary Hub

System Power Supply

Process I/O Subsystem

Control Level

Controller

Figure 3.1 DeltaV system overview diagram

The workstation has all the software to configure the control strategies for the field
device and HMI to monitor and operate process variables. The DeltaV system used in this
 29

research is Version 8 with the operating system Microsoft Windows XP and has OLE for
Process Control (OPC) which stands for Object Linking and Embedding (OLE) for
Process Control, to connect with third party software. The communication between PLC
and computer is Ethernet with redundancy through two hubs.

At the control level, two power sources supply DC power to controllers. I/O modules
function as the interface between field devices and CPU. Typically, there are four kinds
of I/O cards: AI (analog input), AO (analog output), DI (digital input), and DO (digital
output). I/O modules obtain data from field process and convert to discrete signal. Output
cards send the signal from the process unit to drive field devices. One important function
of an I/O card is to isolate high level real world signals from low level signals in the I/O
bus with optical isolators to protect the I/O card. A/D converters in analog input cards
convert analog signal to discrete signal for the/a process unit. D/A converters in input
cards convert discrete signal to analog signal to drive field devices.

In this NPCTF system, there are 25 AI signals, 20 AO signals, 3 DI signals, and 12 DO

signals. The details are listed in Appendix A. Each of the DeltaV I/O cards has 8 channels
for 8 signals. Therefore, it needs 4 AI cards (4x8=32 channels), 3 AO cards
(3x8=24channels), 1 DI card (8 channels), and 2 DO cards (2x8=16 channels).

3.2 System Configuration and Connection

3.2.1 DeltaV cabinet configuration
All devices mounted inside the DeltaV cabinet are shown in Figure 3.2. They mainly
include system power supplies (P1 and P2) which provide 12VDC power for controllers
and other cards mounted on carriers, carriers which hold all the modules, controllers (C1
and C2), I/O cards (AI, AO, DI, and DO), switches, terminals, relays (R_DO1_1~8) and
power supply (PWR1 and PWR2) for all devices in the cabinet. They are the devices at
the control level.
 30

Two power supplies, PWR1 and PWR2, convert 120VAC line power to 24VDC and
provide 24VDC power to the entire DeltaV system in the cabinet. A circuit breaker (CB)
is mounted before two power supplies to protect the system. As indicated in the Figure
3.2, power supply number one (PWR1) supplies 24 VDC power to the system power
supply P1 which converts 24VDC to 12VDC and carrier 3. Power supply number two
(PWR2) supplies 24 VDC power to the system power supply P2 which converts 24VDC
to 12VDC, other carriers, and DO intermediate circuit power through fuse F. Carriers
provide power to all the cards mounted on the carriers. The two switches have separated
AC power supply. R_DO1_1~8 are relays used for connecting AC powered field devices
to DeltaV DO cards which can only connect DC powered field devices. A detailed DO
intermediate circuit is discussed in section 3.2.2.
 31

PWR1 PWR2 PWR2

P1 C1 P2 C2 FB FB PB DN AS-i AI1 AI2 AI3 CARRIER 1

PWR2

AI4 AO1 AO2 AO3 DI DO1 DO2 DO3 CARRIER 2

AC PWR1

P RM DO4 S CARRIER 3

SWITCHES

AI1 AI2 AI3 AI4 AO1 AO2 AO3

RELAYs
1-16 17-32 33-48 49-64 65-80 81-96 97-100 TERMINALs
R_DO1_8
R_DO1_7
R_DO1_6 AO3 DI1 DO1 DO2 DO3 DO4 SPARE
R_DO1_5
101-112113-128129-144145-160161-176177-192193-200 TERMINALs
R_DO1_4
R_DO1_3
R_DO1_2
CB PWR 1 PWR2 F
R_DO1_1

P: System Power Supply PB: Profibus DP DN: DeviceNet S: Serial

C: Controller MD Plus FB: Fieldbus H1 RM: Remote Unit F: Fuse

CB: Circuit Breaker AS-i: Actuator Sensor Interface PWR: Power Supply

Figure 3.2 Device schematic diagram in DeltaV cabinet

3.2.2 I/O card wiring diagrams

I/O cards communicate with CPU through carriers which hold all the I/O cards.
Meanwhile, all the I/O cards need to be wired to the field devices in order to
communicate with field devices.
 32

All the process variables, such as pressure, level, flow, temperature, are sent to the PLC
in the format of 4-20 mA through analog input (AI) cards. Because the 4-20 mA analog
input signals have power source, 4-wire AI cards are used to isolate the power source in
the AI cards to prevent the conflict of the two power sources in the AI signal circuit.
Wiring of the AI card is shown in Figure 3.3. Two wires of each signal from transmitter
(“T”) are connected to the AI card termination (“+” and “-”), as shown in Figure 3.3.

Figure 3.3 AI card wiring [28]

All the manipulated variables (AO), such as opening of valves and current of pumps, are
in the format of 4-20 mA. For analog output (AO) signals to activate the relays of valves
or pumps, the power sources come from AO cards. The two wires of each AO signals
from field devices (“Load”) are directly wired to AO cards termination (“+” and “-”), as
shown in Figure 3.4.
 33

Figure 3.4 AO card wiring [28]

Digital input (DI) signals indicate the switch status. The power source comes from DI
cards. The contacts of the switch are directly connected to the DI card termination (“+”
and “-”), as shown in Figure 3.5.

Figure 3.5 DI card wiring diagram [28]

 34

For digital output (DO) signals, DeltaV DO cards only allow DC power source.
Therefore, except signals of “ROD DOWN”, “DOWN”, “INTERM”, and “HOME”
which are powered by DC, other digital output signals which are powered by AC cannot
be directly wired to DeltaV DO card and, thus, an intermediate circuit is needed.
Therefore, signals “ROD DOWN”, “DOWN”, “INTERM”, and “HOME”, are directly
wired to DO card termination (“+” and “-”), as shown in Figure 3.6. Others, shown as
“Load” in Figure 3.7, are wired to the contacts of the relays (“RELAYS R_DO1_1~8” in
Figure 3.7) in the intermediate circuit and the relays (“RELAYS R_DO1_1~8” in Figure
3.7) are wired to DO cards, as shown in Figure 3.7.

Figure 3.6 DO card wiring diagram [28]

 35

DO1

FUSE
RELAYs
R_DO1_1~ 8

DC NO
POWER AC

Load

Figure 3.7 DO signal intermediate circuit

3.2.3 Connection to field devices

The connection includes connecting the server to the switches which are connected to
PLCs with a Cat5e Internet cable, and connecting I/O cards to field devices using 22
gauge wires, as indicated in Figure 3.8.

The DelatV system has primary and redundant networks. Therefore, there are primary
and secondary ports for two networks in the server. Accordingly, there are two switches
for two networks. Each of two PLCs is connected to two switches: primary port of PLC
will be connected to the primary switch, and the secondary port of the PLC will be
connected to secondary switch. Figure 3.8 shows the wiring.

The wiring from I/O cards to the field devices are connected through terminals in the
DeltaV cabinet and DCS cabinet, as shown in Figure 3.8. The wiring diagrams of each
kind of I/O cards are presented in section 3.2.2.
 36

All signals, their terminal numbers in DeltaV cabinet and DCS cabinet, their cable
number, position in I/O cards, and their signal types are listed in the appendix A.

SERVER Server

SWITCHES

DeltaV
cabinet
AI AO DI DO
PLC PLC

DeltaV
TB

DCS
DCS
TB cabinet

Field
P
TXs
devices
VLVs CONs LDs

Figure 3.8 Schematic diagram of wiring system

The actual devices corresponding to the system indicated in Figure 3.8 are shown in
Figure 3.9 to 3.12. Figure 3.9 indicates the server and the screen. Figure 3.10 shows the
DeltaV cabinet where all the PLCs, I/O cards, switches, DeltaV terminals and powers are
mounted inside the cabinet. Figures 3.11 shows the DCS cabinet where all of the signals
from the DeltaV cabinet are connected to the field devices. Figure 3.12 shows all filed
devices including control valves and transmitters.
 37

Figure 3.9 DeltaV server and screen

PLCs

IO CARDS

SWITCHES

TERMINALS

POWER

Figure 3.10 DeltaV cabinet

 38

Figure 3.11 Wiring of DCS cabinet

Figure 3.12 Field devices of NPCTF

 39

3.3 Programming Architecture Design

As discussed in Chapter 2, there are mainly three functions implemented in this research.
The hardware of the DeltaV system, in order to implement these functions is discussed in
Section 3.2. This section will present the structure to implement the functions.

The whole control structure involves many subsystems and algorithms. A clear and
logical organization of the subsystems and algorithms facilitate not only the running of
the program, but also design maintenance and troubleshooting.

As shown in Figure 3.13, a typical DeltaV system organizes the programming

architecture as hierarchical structure: “Areas”, “Modules”, “Algorithm”, “Function
Blocks or Composites”, and “Parameters”.

Control
Plant
Strategies

Steam
Tank Deaerator Plant Areas
Generator

MTR-101 FIC-101 XV-101

Modules
(2-State Motor) (PID Loop) (Block Valve)

Function Algorithm
Block Diagram (FBD or SFC)

AI PID1 AO FBs

HI_LIM IO_IN Gain SP

Parameters
(Alarm) (Input) (Tuning) (Setpoint)

Figure 3.13 Programming architecture schematic diagram of typical DeltaV system

 40

For NPCTF, control architecture of the whole system, named as “PCTF_SIMON”, is

designed in the “Areas” level. Each sub-system is designed at the “Modules” level, as
shown in Figure 3.14. Each sub-system includes the algorithm and logic which are
programmed using languages of FBD (Function Block Diagram) or SFC (Sequential
Function Chart). Each module consists of different kinds of function blocks with their
own parameters, such as Proportional-integral-derivative (PID). In order to implement the
functions (i.e. process control, safety, sequence, and operation modes) described in
Chapter 2, twenty modules are designed for this NPCTF system, as shown in Figure 3.15.
Each process control loop becomes one module and there are eleven modules for process
control. Each type of I/O signals has one module and, thus, there are four modules for I/O
signals. There are five other modules for safety, sequence, operation mode, stop system,
and ratio.

CONTROL Control
STRATEGIES Strategies

PCTF_SIMON Areas

SG_HX_TANK_L UPPER_TANK_L STOP_SYSTEM Modules

FBD or SFC Algorithm

CALC1 PID1 AI1 FBs

IO_IN (Input) SP (Setpoint) Gain (Tuning) Parameters

Figure 3.14 Programming architecture schematic diagram of NPCTF

 41

Figure 3.15 Programming architecture diagram of NPCTF

 42

3.4 DCS Programming Languages (IEC 61131-3)

As discussed in section 3.3, the modules of the programming architecture are
programmed with industrial languages prescribed in the standard of IEC 61131-3.

The programming of the early PLC was of ladder the diagram type. It resembled the
circuit diagram and still remains one of the most popular PLC programming languages
[29] [30]. However, with the integration of distributed control, sequential control, and
factory control system, the controller is required to do multi-task operations. However,
ladder diagram language is difficult to control application with multiple events occurring
at the same time [31]. Other limitations includes: lack of software structure, problem in
reusability, poor data structure definition, lack of support for describing sequential
behavior, and difficulty in handling complex arithmetical operation [32]. Different PLC
manufacturers developed their own programming languages to solve these problems. The
multiplicities of languages and even proprietary programming languages or tools were
too complex for customers to handle. Standardization of these practices became
necessary. IEC adopted the prevalent programming practices of major PLC
manufacturers and published the standard IEC 61131-3. In fact, language defined by IEC
61131-3 is also recommended to implement application functions of nuclear power plants
[33].

IEC 61131-3 is the standard of programmable language and defines 5 kinds of languages:
Instruction List (IL), Ladder Diagram (LD), Function Block Diagram (FBD), Structured
Text (ST), and Sequential Function Chart (SFC). FBD and SFC are the two main
programming languages supplied by the DeltaV system and used in the research for
programming.
 43

3.4.1 Function block diagram (FBD)

FBD is one of the graphical languages in the IEC61131-3 for programmable logic
controller design. It uses the following graphical conventions as shown in Figure 3.16
[32]:

 A function block is a rectangular bock with inputs entering from the left and
outputs exiting from the right.

 The name of the function block and its instance are shown on top of the block.

 The inputs and outputs of the function block are shown within the block.

FB Type FB
Instance

Inputs Outputs

Figure 3.16 Individual function block

The function block diagram (FBD) network includes connections, graphical elements for
execution control (“Jump” in Figure 3.17), and graphical elements to call function or
function blocks. Some platforms of manufacturers include connectors which are used to
construct long network. These connectors are not control or data flow elements [34].

Connections are horizontal or vertical lines which carry the signal and connect the
functions and function blocks. Signals flow from left to right or from top to bottom along
the connections. Left or top is input, and right or bottom is output. In special cases, the
signals can be fed back, as shown in Figure 3.17. It is possible to split a line into several
 44

connections. For example, in Figure 3.17, the connection from “OUT” of “AI1” is split
into two connections. However, it is forbidden to connect more than one output to one
input. For example, in Figure 3.17, it is not allowed to connect more than one connection
to “CAS_IN” of “AO1”. Different data type of variables, such as a floating-point double
word or Boolean value, can flow along the connections. However, the output parameter
must be the same data type as the connected input parameter.

In an FBD network, the execution could transfer from one part of network to another. As
shown in Figure 3.17, “PV” points to the signal from “AI1” to other part of FBD network.

The graphical representations for calling an FB or function are similar. They have input
and output parameters which are indicated in the block, as “PID” in the Figure 3.17.

Jump
Connection FB Feedback

Figure 3.17 FBD Network

The FBD network is evaluated by PLC according the following rules:

 Before the functions or function blocks in the network are evaluated, all the inputs
values from other elements must be available.
 45

 The outputs of a function block cannot be considered available until all its outputs
have been evaluated.

 The FBD network is not complete until all the outputs of its functions and
function blocks have been evaluated.

3.4.2 Sequential Function Chart (SFC)

Sequential function chart (SFC) is a graphical language for programmable logic
controllers (PLCs). It is one of the five languages defined by IEC 61131-3 standard. It
can be used to program processes that can be split into steps.

As shown in Figure 3.18, the sequential function chart (SFC) network consists of Steps
(rectangular boxes: S1 to S4), Transitions (bars with identifiers: T1) and Links. Steps are
associated with actions, Transitions are logic conditions, and Links connect Steps and
Transitions. A Step is either active or inactive. When a Step is active, the associated
actions are executed until the Step becomes inactive. The status of active or inactive is
decided by Transition. The Transition is programmed by Transition condition which is a
Boolean expression. When the Transition becomes true, the Step immediately before it
becomes inactive and the one immediately after it becomes active. Therefore, the
processes with a step by step state behavior are suitable for programming with SFC.

Link

Figure 3.18 SFC network

 46

3.5 Programming Algorithms for Modules

The purpose of the programming is to implement the functions described in Chapter 2.

Section 3.3 discussed the programming architecture of this project. Modules of the
programming architecture are implemented by programming. Under the structure, as
shown in Figure 3.19, modules of STOP_SYSTEM and SEQUENCE are step by step
with sequence in nature and, thus, are programmed using SFC language. For the
STOP_SYSTEM, when the operator wants to stop the system, the system is reset to
original status, i.e. all valves to normal status: open for NO (normal open) valves and
closed for Normal Close (NC) valves; all the heaters, and pumps are stop; and all the
tanks are empty. The operation of these devices is sequential. The main purpose of the
SEQUENCE is to fill up the pipes and tanks. The filling procedure is step by step. Refer
to Figure 2.4 in Section 2.3 for the logic procedure and Section 2.3 for more function
details. The Pressurizer is first filled up and then the HX Tanks. The Upper Tank is the
last one to fill up; therefore, they are programmed using SFC language. Detailed
programming is shown in appendix D.

Other modules are programmed using FBD. AI, AO, DI, and DO modules are the
interfaces between signals from and to local devices and programming algorithm. The
SAFETY module is used to implement the safety functions of SDS1, SDS2, and ECC
described in section 2.4 (referring Figure 2.5 to 2.8 in section 2.4 for their logic
diagrams).

The module of OPERATION_MODE implements three kinds of operation modes

described in section 2.5, Normal, Solid, and Open mode (referring to Figure 2.11 and
2.13 in section 2.5 for logic diagrams). Other modules, such as HX_OUTLET_T, are the
controller algorithm for process control described in section 2.2.
 47

Figure 3.19 Programming architecture of NPCTF

3.6 Human Machine Interface (HMI) Configuration: Graphics and

Faceplates
The Human Machine Interface (HMI), as indicated in Figure 3.20, is created mainly to
monitor and control the process in order to implement the functions introduced in
Chapter 2: process control, sequence control, safety shutdown, and operation modes. It is
similar with the P&ID diagram of NPCTF of Figure 2.2 in Chapter 2.

There are two kinds of graphics of HMI: dynamic pictures and static pictures. Static
pictures do not change their properties while dynamic pictures communicate with the data
base to change their properties or database. Static pictures show the process system:
devices and pipes, tanks. Dynamic pictures indicate the process status and are used to
operate the process through faceplates and buttons. For example, when press the button
 48

“STOP SYSTEM” in Figure 3.20, the button becomes brown and the system is also
stopped.

All the valves, except manual valves, indicate the full open status as red color, full closed
status as green and between full open and closed as yellow. If the safety system, “Safety”
in Figure 3.20, is active, the HMI will show the active one in red: SDS1, SDS2, or ECC.
From HMI, as show in Figure 3.20, the operator can operate the Pumps, Heater, and
Chillers, stop the system, start the sequence, and select the operation modes through
related buttons, as indicated in Figure 3.20. For process control, faceplate is the interface
for operator to control the process. By clicking the “Faceplate” icon in HMI, the operator
can open the faceplate window as shown in Figure 3.21 to perform the operation of
process controllers: select values of set-point or output, manual or auto. By click the
“trend” in the faceplate, operator can open the trend window as shown in Figure 3.22 to
monitor the current trend of three parameters of controller: process variable (PV), set-
point (SP), and controller output (OUT). The controller is also allowed to change the
controller tuning parameters through “detail” icon in faceplate, as shown in Figure 3.23.
 49

Stop
Sequence

Operation
modes
Faceplate
Safety

Figure 3.20 HMI of NPCTF

 50

Detail
Trend

Figure 3.21 Typical faceplate

Figure 3.22 Current trend of controller parameters

 51

Figure 3.23 Controller tuning parameters

3.7 Summary

In summary, this chapter has described the construction and design of the DeltaV DCS
system which is used to implement the functions explained in Chapter 2. The
programming to implement these functions in this DCS system is presented in this
chapter. The main industrial languages, FBD and SFC, used to make the program are
explained. The design of HMI used to operate the NPCTF is also discussed in the chapter.
 52

Chapter 4
Process Controller Design in DeltaV DCS
As described in Chapter 2, process control is part of the functions designed and evaluated
in this research. This chapter describes the design of controller for process control. There
are 11 process control loops which are given in Appendix B. Focus is given to the SG
Tank level control to illustrate the detail analysis and design process. Other loops are
tuned based on experience.

4.1 Development of Control Strategies

For process control described in Chapter 2, the feedback control system shown in Figure
4.1 is designed to control the process variables (PVs). The process variables, such as
Heater outlet temperature (T2), are measured and sent to the controller. The controller
compares the measured variable with the value set by operator (SP) and calculates the
action (M) needed to change the process in order to make the process variable equal to
the value designed by the operator.

SP E
Controller Process
+ M PV
_

Figure 4.1 Process control diagram

For controller algorithm in DCS system, such as DeltaV system, the control strategies
could be advanced control strategies. The NPCTF in this research is tested with PID
controllers which are widely used in variable industries.
 53

4.1.1 Proportional-integral-derivative (PID) algorithm

Error (E):

Error (E) is defined as the deviation from set-point [35]. For different DCS systems, the
definition of error may be different. In DelatV system, E is defined as [28]:

E = SP – PV (4.1)

where

SP is an input variable that sets the desired value of the controlled variable manually,
automatically, or by means of a program in the same units as the controlled variable.

PV is the process variable to be controlled, such as water temperature, pressure, level, etc.

Proportional Control (P):

Proportional action keeps the output of the controller in proportion to the error:

K c is the controller gain. E is the error between set-point and process variable. M is the
output of the controller. The term C is necessary since it is hard to be the case that zero
error coincides with zero controller output.

In order to obtain the value of the controller output, it also needs to know C. Therefore,
another form of controller output is often used. Assume current error is En, and previous
error is En-1, then we have:
 54

Subtracting (4.3) by (4.4) gives:

Using this version to calculate the controller output, it needs to calculate the current and
previous errors between set-point and process variable.

Integral Control (I):

Integral control eliminates the offset of the process variable from the set-point. It keeps
changing the controller output as long as the error exists:


I
dM K c
E (4.6)
dt

 I is integral time. Integrate both sides, and the following can be obtained.

M  Edt
I
Kc
(4.7)

If the scan interval is Ts , the discrete form of the equation becomes:

M  K c
I
Ts (4.8)
En

Derivative Control (D):

Very few industrial controllers use derivative action because of noise [35]. The principle
behind derivative action is if the error changes quickly, it can become large in the future.
Derivative action tries to prevent this change by changing the output in proportion to the
change rate of error E:

M  Kc D
dE
(4.9)
dt

 D is the derivative time which can be adjusted. The discrete form of the above equation
is:
 55

En  En 1
M n  Kc D
(4.10)
Ts
Previous scan interval is:

En 1  En 2
M n 1  Kc D (4.11)
Ts
Subtracting (4.10) by (4.11)

Kc D
M  ( En  2 En 1  En 2 ) (4.12)
Ts
For PI control:

Conventional analog form is:

M  K c  E   Edt 
 
I
1
 
(4.13)

Discrete form is:

 
M  K c ( En  En 1 )  s En 
I 
T

(4.14)

For PID control:

Conventional analog form is:

M  Kc  E   Edt   D
 dE 
I dt 
1 (4.15)

Discrete form is:

  
M  Kc ( En  En 1 )  s En  D ( En  2 En 1  En 2 ) 
I
T (4.16)
 Ts 

4.1.2 Control loops with two actuators

In an NPCTF system, there are a couple of loops which process variables are adjusted by
two valves – one mainly to increase the process variable and another to decrease the PV.
 56

For example, valves CV-13 and CV-16 are used to control the water inventory pressure
P1, as shown in Figure 4.2. While CV-16 is mainly used to increase the pressure P1 and
CV-13 is used to decrease pressure P1, CV-16 can be closed to decrease the pressure P1
and CV-13 can be closed to increase the pressure P1. The question is that, if the pressure
P1 is increased, should it increase CV-16 or decrease CV-13? In order to solve this
conflict, the opening of one of the valves is fixed and another valve controls the process
variable. The two actuator loops and the fixed valves are shown in Table 4.1.

CV-13

P1
CV-16

Figure 4.2 Diagram of water inventory control process

 57

Table 4.1 Control loops with two actuators

Pressurizer pressure CV-9(Main) P4 (air pressure)

CV-10(Fixed)

Pressurizer level CV-12(Fixed) L3 (water level )

CV-16(Main)

Water pressure CV-16(Main) P1 (water pressure )

CV-13(Fixed)

Upper Tank level CV17(Main) L1 (water level)

CV15(Fixed)

4.2 Controller Analysis and Design for Steam Generator Level

Control
For the functions of process control in the DCS system, there are 11 loops. This section
takes the example of the SG tank level as process controller analysis and design.

4.2.1 Process model

4.2.1.1 Method of constructing model
Model identification is the process of quantifying the process dynamics. The model can
be used for simulation or control strategy analysis and design. Different purposes require
different accuracy of the models of the real process.
 58

In control engineering, FOPDT (first-order-plus-dead-time) and SOPDT (second-order-

plus-dead-time) are used to represent the main features of various process responses. For
the model structure, FOPDT and SOPDT are widely used in controller design and
controller tuning in various process industries [36]. In this research, a model is created
mainly for the purpose of control strategy analysis and design. Therefore, the process can
be modelled as first order plus dead time or second order plus dead time. Models
constructed here are FOPDT, given by equation 4.17, or SOPDT, given by equation 4.18:

G( s)  e  s
Kp
1   ps
(4.17)

G( s)  e  s
Kp
a2 s  a1s  1
2 (4.18)

where K p is process static gain;  p is time constant; and θ is process delay.

The techniques available can be categorized into two approaches, open loop test and
close loop test. For the open loop test, the controller (if existing) is put into manual mode
and the disturbance is applied to the process through changing the output of the controller
(M). The response of the system is then measured. If the controller exists and provides
some level of control, the close loop test can be used to identify the process model. This
test is performed by putting the controller in Auto mode and changing the set-point of the
controller.

For this research, all the models are identified by the open loop test since the system is
new and no previous controller existed. The MATALB System Identification Tool is
used to identify the process model.

The identification of a process model involves three basic steps [37].

1. The data record. In this step, it should be decided what variables are to be measured
and what variables are to be applied to the process. How much data should be recorded?
 59

What is the sampling time? The result is the input-output data for model developed. This
step is illustrated by “Experiment Design” and “Data” in Figure 4.3.

2. The set of models or the model structure. This step is the most important. The model
structure should be combined with the purpose of the model. If there is information about
the model structure and physical process, this information should be combined to
construct the model. The parameters are adjusted to reflect physical consideration. This
model set is called grey box. If there is no information about the physical process, the
parameter is adjusted to fit the data. This model set is called black box. This step includes
“Choose Model Set,” “Choose Criterion to Fit,” and “Calculate Model” in Figure 4.3.

3. The determination of the “best” model in the set, based on available data. This step
assesses the model quality. The basic approach is to compare the data produced by the
model with the experiment data. In Figure 4.3, this step includes the “Validate Model.”

Priori
Knowledge

Experiment Choose Model

Design Set

Data Choose
Criterion to Fit

Calculate Model

No
Validate Model

Yes

Figure 4.3 Diagram for system identification procedure [37]

 60

In this research, the controller is put into Manual mode and output of the controller (MV)
is applied to the process. The process variable is measured. The output of the controller
is recorded as input data and the process variable as output data. By this method, the data
for modelling is recorded. The MATLAB System Identification tool is used to identify
the process model.

4.2.1.2 SG Tank level process model

The level of SG HX Tank (L4) is controlled by valve CV-25, as shown in Figure 4.4.
However, CV-25 cannot be used to decrease the tank level. Valve CV-18 is required to
decrease the level. Experiments show the opening of 40% of CV-18 is the best. Therefore,
the opening of CV-25 is the input, and tank level L4 is the output of this process model.
When the CV-25 opens at 17%, the level is balanced and stable. In order to develop the
model of SG HX Tank level control, the CV-25 is open from 17% to 27%, and the level
L4 is measured. CV-18 keeps 40% opening as normal running status.

L4

CV-25 CV-18

Figure 4.4 Diagram of SG HX Tank level control

The data was drawn from experiment described above, and the relationship between input
and output is shown in Figure 4.5. From the Figure 4.5, the response has time delay.
 61

L4 (%)
CV-25 (%)
Time (s)

Figure 4.5 Input and output curve from experiment data

The MATLAB System Identification Tool and the PEM (Prediction Error Methods) are
used to estimate the model. It is an SOPDT (second-order-plus-dead-time) system. The
model is as following:
G( s)  e 18s
0.007272
s(1  29.883s) (4.19)

This model has a 94.87% fit to the model. The Final Prediction Error (FPE) is 0.0073,
and the Mean Square Error (MSE) is 0.01152. Therefore, the designed model fits the
experiment’s data.

From Eqn. (4.19), the process has a time delay of 18 seconds. The delay is produced
because the control valve CV-25 is small, and the volume of the tank is big. It takes time
for level change becoming significant enough for the transmitter to be able to read the
change.

4.2.2 Stable analysis

The controller design should guarantee the stability of the system. In order to judge the
stability of a system, general stability criterion is: A necessary and sufficient condition
for a feedback system to be stable is that all the poles of the system transfer function have
negative real parts [38].
 62

Bode Stability Criterion:

Definitions [39]:

Critical Frequency c is defined to be the value of  for which

OL ( ) = -180O. This frequency is also referred to as a phase crossover frequency.

Gain Crossover frequency g is defined to be a value of  for which AROL( ) = 1.

Consider an open-loop transfer function (as shown in Figure 4.6) that is

strictly proper (more poles than zeros) and has no poles located on or to the right of the
imaginary axis, with the possible exception of a single pole at the origin. Assume that the
open-loop frequency response has only a single critical frequency c and a single gain
cross frequency g , then the closed-loop system is stable if amplitude ratio AROL(c) < 1.
Otherwise, it is unstable [39].

SP E PV
Gc Gp
+
_

Figure 4.6 Block diagram of closed-loop

4.2.3 Controller parameters tuning using Simple-IMC method

Numerous tuning techniques have been reported in the literature for setting the
parameters of a PID controller. In 2000, O’Dwyer did a survey from literature regarding
the tuning techniques for PI and PID controllers [40]. For self-regulating process, there
were at least 81 methods for tuning PI controller and 117 methods for tuning PID. For
integrating processes, at least 22 tuning method for PI controller and 15 for PID
 63

controller have been published. However, each one of these methods has at least one
flaw [41].

Ziegler Nichols (ZN) method is the basic and one of the most popular tuning techniques
mentioned in the literature. However, it is aggressive and easy to cause oscillation. The
IMC PID tuning method by Rivera [42] causes poor disturbance response for integrating
processes [43] [44]. The Simple Internal Model Control (SIMC) has good performance
for both integrating and pure time delay processes and for both setpoints and load
disturbances [45].

The SIMC method starts from the IMC PID tuning rules by Rivera [42], and is closely
related with direct synthesis tuning rules by Smith and Corripio [46]. It modifies the
integral term to improve disturbance rejection for integrating processes.

As indicated in [45], for integrating process with delay and lag with transfer function as
following:
e  s
G p ( s)  K p
s( 2 s  1)
(4.20)

the SIMC method uses the following tuning rule to calculate the parameters for cascade
PID (controller Gc) in the closed loop as shown in Figure 4.6:

Kc   I  4( c   ) D  2
K p ( c   )
1
(4.21)

where K p is process static gain;  2 is time constant; θ is process delay; K c is gain of

controller;  I integral time of controller ; and  D derivative time of controller.

 c is tuning parameter and determined by the trade-off between fast response (small value
of  c) and stability (large value of  c). For fast response, this value is suggested as  c   .

D D
For ideal PID, the tuning rule is

Kc'  aKc  I'  a I  D'  a  (1 

I
)
a (4.22)
 64

The SIMC tuning rules as indicated in equations (4.21) and (4.22) are used to calculate
the parameters of controller of SG Tank level control. For SG Tank level process, as
constructed in section 4.2.1, the model is

G( s)  e 18s
0.007272
s(1  29.883s)

For this model, the process gain (K p), time delay (θ) and time constant ( 2) are as following:

K p = 0.007 θ = 18 seconds  2 = 29.88 seconds

SMIC tuning technique is used to calculate the parameters as following:

 c = θ = 18 seconds

Therefore,

Kp c 
1 1
0.007 (18  18)
1 1
Kc = = = 4.0

 I  4( c   ) = 144 seconds

 D   2 = 29.88 seconds

For ideal PID controller, the coefficient is

D
a  (1  ) = 1
I
29.88
= 1.21
144

Therefore, the parameters for ideal PID controller are:

Kc'  aKc = 1.21x4.0 = 4.84

 I'  a I = 1.21x144 = 174 seconds

D
 D' 
29.88
= = 24.6 seconds
a 1.21

After tuned by SIMC with the controller parameters of proportional gain of 4.84, integral
time of 174 seconds and derivative time of 24.6 seconds, the Bode diagram is shown in
 65

Figure 4.7. As shown in the Figure 4.7, the gain margin is reduced from 8.31 (18.4dB) to
2.83 (9.04dB) which is between 1.7 and 4 suggested by Seborg [39]. The system is still
stable because the gain margin is greater than zero.

Figure 4.7 Gain and phase margins on a Bode plot

4.2.4 Comparison of tuning results in MATLAB and on NPCTF

In order to compare the tuning results between MATLAB and NPCTF, the control system
is built in MATLAB Simulink as shown in Figure 4.8. In the Figure 4.8, the “signal 1”
which stands for set-point of the controller is built to change from 30% to 33%, 33% to
36%, and then 36% to 39%, as did in the experiment in NPCTF. Function of “Saturation”
is added between PID and process transfer function to limit the opening of valves within
100%. Transfer function created in Section 4.2.1 is used to represent the SG Tank level
process. PID is tuned as described in Section 4.2.3.2. Performance from Simulink is
shown in Figure 4.9. The same PID parameters are applied in DelatV system for SG Tank
level PID controller. To obtain the performance of the SG Tank level controller, its PID
controller in the DeltaV system is set in Auto and then change set-point from 30% to 33%,
33% to 36%, and 36% to 39%, respectively. The level performance is shown in Figure
 66

4.10. The overshoot and rise time (time to reach set-point) from MATLAB and NPCTF
are calculated in Table 4.2. It can be observed from the Table 4.2 that, the overshoots
between results from MALAB and NPCTF are similar. However, with the NPCTF
system, it takes more times to reach set-point because of the stiction and hysteresis of the
valves [35].

Figure

Figure 4.8 Function block diagram of close loop control

Figure 4.9 SG Tank level responses from Simulink

 67

Figure 4.10 SG Tank level responses from NPCTF experiment

Table 4.2 Overshoot and rise time from simulation of MATLAB and NPCTF
experiments

30% - 33% 33% - 36% 36% - 39%

Rise
Overshoot Rise time Overshoot Rise Time Overshoot Time
(%) (seconds) (%) (seconds) (%) (seconds)
MATLAB 26.40% 50 30.90% 50 31.10% 86
Experiments 20.70% 108 31.40% 108 32.80% 131

4.3 Empirical Tuning Methods for Process Loops

Empirical methods are applied to tune process controllers, except SG Tank level
controller discussed in the previous sub-section.
 68

In industry, the process model is often hard to obtain and the controller parameters are
generally obtained from a similar process and, thus, adjustment is necessary. Moreover,
there is always mismatch between the model and real process. Therefore, the controller
parameters, based on the model, are required to be adjusted. The PID parameters are
adjusted based on the effect of P (proportional), I (integral), or D (derivative) to the
performance of the process controller.

The general rule is that, for proportional only controller, increasing controller gain Kc
reduces the rise time and offset at steady state, but demonstrates more oscillation
behavior. The Proportional controller always has an offset at steady state. The rule is
shown in Figure 4.11.

2 4 6 8 10 12
minutes

Figure 4.11 Effect of changing Kc [35]

Adding integral action can cancel the offset, but increase the overshoot. More integral
action, less integral time Ti, will reduce rise time, but increase overshoot, as shown in
Figure 4.12. Less integral action, more integral time Ti, takes a long time to achieve at set
point.
 69

In fact, PI controller is adequate for many processes and simplifies the tuning procedure
when using empirical method.

2 4 6 8 10 12
minutes

Figure 4.12 Effect of changing Ti [35]

Main function of derivative action is to anticipate the changing trend. For the process
with maintaining the rate of change, derivative action can be added in the controller.

Flow process will not maintain the current rate of change for any appreciable time in the
future and, thus, derivative action is not recommended in the flow control loop.
Temperature process responds slowly and tends to maintain the rate of change, so
derivative action is recommended for the temperature control loop [47].

The loops tuned by empirical method and their PID parameters are listed in Table 4.3.
 70

Table 4.3 PID parameters of process controller tuned by empirical method

Loops P I D MV
(Gain) (Reset: seconds (Rate:
per repeat) seconds)
PRESSURIZER_L 4.0 100.0 15.0 CV-16
PRESSURIZER_P 1.3 21.3 0.0 CV-9

PRIMARY_WATER_F 0.6 16.8 0.0 CV-1

SG_HX_TANK_P 0.8 45.0 20.0 CV-21
UPPER_TANK_L 3.0 250.0 10.0 CV-17
WATER_HEATING 3.0 30.0 0.0 C2
WATER_INVENT_P 1.36 65.0 16.4 CV-16

4.4 Summary

In brief, this chapter explains the controller algorithm of all process control loops. SG
Tank level is given as an example to illustrate the model construction, analysis of the
model, and controller design and tuning. The design is compared in MATLAB
environment and NPCTF, and shows similar results. Other loops are tuned on empirical
method and parameters of the controller are given in this chapter.
 71

Chapter 5
Evaluation and Testing of the DCS Operated NPCTF
The purpose of this chapter is to evaluate if the DeltaV system designed can perform the
functions described in Chapter 2 which mainly include: process control, sequence control,
safety systems and operation modes. The DelatV system is configured and programmed
in Chapter 3, and the process controllers are designed in Chapter 4. For safety systems,
safety conditions are created and checked if the safety systems in the DelatV system can
respond as described in Chapter 2. In operation modes, different operation modes are
selected and examined if the related actions, such as the opening or closing of the valves,
are performed as described in Chapter 2. Sequence control is involved during the start-up
of the system. During the start-up of the system, related tanks are inspected if they are
filled up sequentially. For process control, the set-points of controllers are changed from
different operating points and checked if there are oscillation for the responses and there
are too many overshoots.

5.1 Process Control

In this Chapter, functions such as primary water flow control, water heating control, HX
Tank pressure control, Pressurizer pressure control, Pressurizer water level control,
Upper Tank level control, and water inventory pressure control are evaluated. The
controller is tuned at one operating point and also tested if it works properly at other
operating points.

5.1.1 Evaluation methods

In order to evaluate the dynamic performance of a control system in time domain, the
following specifications are widely used [38], as shown in Figure 5.1.

In Figure 5.1, percentage overshoot is the amount by which the system output response
proceeds beyond the desired response, given by the formula (5.1):
 72

M pt  fv
P.O.   100%
(5.1)
fv
where

P.O. denotes percentage overshoot;

M pt denotes peak value of the time response; and

fv denotes the final value of the response.

Rising time is defined as the time for a system to respond to a step input and attain a
response equal to a percentage of the magnitude of the input. For under-damped systems,
the 0% to 100% rise time is normally used, and for over-damped systems, the 10% to 90%
rise time is commonly used [38].

Settling time is the time required for the system output to settle within a certain
percentage of the input amplitude, such as 5% of the final value. In this research, 5% is
used to evaluate the performance [48].

Figure 5.1 Performance specifications in time domain

 73

5.1.2 Primary water flow control

The evaluation of the primary water flow control is performed by setting the controller of
primary water flow to Auto mode, and the set-point is changed from 9 to 6 and then 6 to
9. The response of primary water flow is shown in Figure 5.2 in red line. The blue line
shows the change of set-point and the green line shows the output of the controller. It can
be observed that the process variable, primary water flow, can track the set-point without
oscillation.

Figure 5.2 Primary water flow performance

When the set-point is dropped from 9 to 6, the response is shown in Figure 5.3. In Figure
5.3, there are four straight red lines which indicate the beginning and final set-point
values and error band of the final value. The blue line is the response curve. From Figure
 74

5.3, it can be seen that the response has an overshoot of (6-5.71)/(9-6) = 9.7%, a rising
time of (52-30) = 22 seconds and a settling time of (70-30) = 40 seconds.

Error band

Figure 5.3 Performance characteristics of step response of decrease primary water flow

The increase of the set-point from 6 to 9 shows the response in Figure 5.4. In Figure 5.4,
six straight red lines indicate the beginning and final set-point, 10% and 90% total change
of set-point, and error band. From the curve, it can be found that the response is over-
damped and there is no overshoot. It has rising time of (63-49) = 14 seconds and a
settling time of (65-45) = 20 seconds.

Error band
90% change

10% change

Figure 5.4 Performance characteristics of step response of increase primary water flow
 75

The step response is over-damped to increase the set-point and under-damped to decrease
the flow. Moreover, it responds faster when increasing the set-point. Therefore,
characteristics of increasing the flow and decreasing the flow are different and, somehow,
nonlinear.

5.1.3 Water heater control

In order to evaluate the water heating control, the controller of water heating is set to
Auto mode. The set-point is changed from 30℃ to 25℃ and then 25℃ from to 30℃; the
responses are shown in Figure 5.5. As indicated at the bottom of Figure 5.5, “Parameter
Reference”, blue line denotes the temperature changes, green for set-point change, and
red line for output of the controller. The process variable and temperature can track the
set-point.

Figure 5.5 Heater outlet temperature performance

 76

When drop heater outlet temperature set-point goes from 30℃ to 25℃, the temperature
response is shown in Figure 5.6. The blue line shows the temperature response with time.
Four straight lines indicate the beginning and final set-point values and error band of the
final value. From the curve, it can be seen that the overshoot is (25-24.85)/(30-25) = 3%,
rising time is (177-52) = 125 seconds, and settling time is (143-52) = 91 seconds.

Error band

Figure 5.6 Performance characteristics of step response of decrease heater outlet

temperature

When the temperature set-point is increased from 25℃ to 30℃, the transient response is
shown in Figure 5.7. The rise time is calculated from 10% to 90%. It has a rise time of
(148-86) = 62 seconds and a settling time of (185-82) = 103 seconds. The system is a
poor damping system and difficult to describe the system using the second-order model
giving the oscillatory performance.
 77

Error band
90% change

10% change

Figure 5.7 Performance characteristics of step response of heater outlet temperature

Comparing the responses between increasing and decreasing the temperature setpoint, it
responds faster when increasing the set-point. Therefore, the characteristics of increasing
the temperature and decreasing the temperature are different and nonlinear.

5.1.4 HX Tank pressure control

To evaluate the HX tank pressure control, the HX tank pressure controller is set to
AUTO and the set-point is changed from 0 to 2psig, 2psig to 3psig, and then to 4psig.
The pressure response is shown as a red line in Figure 5.8. The blue line and green line
show the set-point and controller output respectively. From the Figure 5.8, the pressure
tracks the set-point better from 0psig to 2psig and worse from 3psig to 4psig.
 78

Figure 5.8 HX tank pressure performance

When the set-point of tank pressure is changed from 0psig to 2 psig, the pressure
response is shown as a blue line, as in Figure 5.9. . Its response is over-damped, and the
rise time is calculated from 10% to 90%. It has an offset which is (2-1.866)/2 = 7.25%
and rise time of (104-17) = 87 seconds.
 79

90% change

10% change

Figure 5.9 Performance characteristics of step response of HX tank pressure (0psig-2psig)

The response from 2psig to 3psig is shown in Figure 5.10. It has a bigger offset which is
(3-2.8)/(3-2) = 20%. It has a settling time of (176-31) = 145 seconds when a 20% offset is
acceptable.

Figure 5.10 Performance characteristics of step response of HX Tank pressure (2psig-

3psig)
 80

The response from 3psig to 4psig is shown in Figure 5.11. It has a bigger offset which is
(4-3.36)/(4-3) = 65%.

Figure 5.11 Performance characteristics of step response of HX Tank pressure (3psig-

4psig)

Therefore, the step response from 0psig to 2psig, 2psig to 3psig, and 3psig to 4psig is
different and the process is nonlinear. The controller can control the HX Tank pressure.

5.1.5 Pressurizer pressure control

In order to assess the Pressurizer pressure control, the Pressurizer pressure controller is
set in AUTO and its set-point is changed from 2psig to 3psig, 3psig to 4psig, and 4psig to
5psig, respectively. The pressure response is shown as a red line in Figure 5.12. The blue
line indicates the set-point and a green line for the output of the controller. From the
curve, the pressure of the pressurizer can tack the set-point without oscillation.
 81

Figure 5.12 Pressurizer pressure control performance

When increasing the set-point of the pressure of the pressurizer from 2psig to 3psig, the
response is shown in Figure 5.13. The response has an overshoot of (3.066-3)/(3-2.108) =
7.4% and a rise time of (138-55) = 83 seconds.

Figure 5.13 Performance characteristics of step response of pressurizer pressure (2psig-

3psig)
 82

If the set-point is changed from 3psig to 4psig, its response is shown in Figure 5.14. It is
over-damped and has an offset of (4-3.907)/(4-3.008) = 9.4% and rise time of (117-34) =
83 seconds.

Figure 5.14 Performance characteristics of step response of pressurizer pressure (3psig-

4psig)

The response in Figure 5.15 shows an increase in the set point from 4psig to 5psig. It is
over-damped and has an offset of (5-4.975)/(5-3.911) = 2.3% and rise time of (42-25) =
17 seconds.

90% change

10% change

Figure 5.15 Performance characteristics of step response of pressurizer pressure (4psig-

5psig)
 83

Therefore, the response from 2psig to 3psig is under-damped and 3psig to 4psig and
4psig to 5psig are over-damped. The process is nonlinear. The controller can control the
pressure of the Pressurizer.

5.1.6 Pressurizer water level control

To evaluate the Pressurizer level control, the Pressurizer water level controller is set to
AUTO and its set-point is changed from 42% to 45%, then from 45% to 50%. Its
response is shown in Figure 5.16. The red line, blue line, and pink line indicate
pressurizer pressure, set-point, and controller output respectively.

Figure 5.16 Pressurizer water level control performance

When the set-point of the level is increased from 42% to 45%, in fact 42.85% to 45%, it
takes (397-59) = 338 seconds to reach the maximum. It has an overshoot of (46.13-
45)/(45-42.85) = 52.6% and a rise time of (245-59) = 185 seconds.
 84

Figure 5.17 Performance characteristics of step response of pressurizer level (42%-45%)

When the set-point of the level is increased from 45% to 50%, it takes 289-42=247
seconds to reach the maximum. It has an overshoot of (51.77-50)/(50-45) = 35.4% and a
rise time of 132-42 = 90 seconds.

Figure 5.18 Performance characteristics of step response of pressurizer level (45%-50%)

In conclusion, the response from 42% to 45% and 45% to 50% are different and, thus,
nonlinear. The controller can control the process without oscillation.
 85

5.1.7 Upper Tank level control

In order to assess the Upper Tank level control, the Upper Tank level control is set to
AUTO and its set-point is changed from 30% to 35%, 35% to 40%, and then 40% to 45%.
The response is shown in Figure 5.19. The red line, blue line and green line indicate the
tank level, controller set-point and output, respectively.

Figure 5.19 Upper tank level control performance

When the set-point of the level is increased from 30% to 35%, the response is shown in
Figure 5.20. It takes (210-54) = 156 seconds to reach the maximum. It does not have an
overshoot and rise time of (126-54) = 72 seconds.
 86

90% change

10% change

Figure 5.20 Upper Tank level step response from 30% to 35%

When the set-point of the level is increased from 35% to 40%, the response is shown in
Figure 5.21. It takes (189-49) = 140 seconds to reach the maximum. It has an overshoot
of (41.03-40)/(40-35) = 20.6% and a rise time of (125-49) = 76 seconds.

Figure 5.21 Upper tank level step response from 35% to 40%

When the set-point of the level is increased from 40% to 45%, the response is shown in
Figure 5.22. It takes (189-49) = 116 seconds to reach the maximum. It has an overshoot
 87

of (47.04-45)/(45-41.21) = 53.8% and a rise time of (117-51) = 66 seconds. The

overshoot at an operating point of 40% is high since the Upper Tank is nonlinear tank and
PID parameters are tuned to an operating point of 30%.

Figure 5.22 Upper tank level step response from 40% to 45%

In conclusion, the responses from 30% to 35%, 35% to 40%, and 40% to 45% are
different and nonlinear. The figures show that the controller can control the process
without oscillation.

5.1.8 Water inventory pressure control

To evaluate the water inventory pressure control, the water inventory pressure controller
is set to AUTO and its set-point is changed from 3psig to 5psig. The response is shown in
Figure 5.23. The brown line, blue line, and pink line indicate pressure, controller set-
point, and controller output, respectively.
 88

Figure 5.23 Primary water pressure P1 step response

When the set-point of the pressure controller is increased from 3psig to 5psig, its
response is shown in Figure 5.24. It takes (296-125) = 171 seconds to reach the
maximum. It has an overshoot of (5.715-5)/(5-3.076) = 37.2% and a rise time of (247-125)
= 122 seconds. Therefore the overshoot is high, but only takes 2 minutes to reach the set-
point. The controller can control the pressure.
 89

Figure 5.24 Primary water pressure P1 step response from 3 psig to 5 psig

In conclusion, most of the processes are, somehow, nonlinear. The PID tuning that has
good performance at one operating point does not have perfect performance at other
operating points. Some processes have very nonlinear characteristics and it is better to
develop nonlinear control techniques in future research. However, the controllers
designed can reasonably control the process.

5.2 Sequence Control

When the “STARTUP” button, as shown in red box in Figure 5.26, is pressed, the system
begins the procedure of filling up the tanks to get the system ready for running. The
procedure is that the Pressurizer Tank is filled up first and then the HX Tank, and the
Upper Tank is the last one to fill up. The level change of each tank is shown in Figure
5.25. As shown in Figure 5.25, the pressurizer level L3 begins to increase. When the
Pressurizer level reaches its designed value, the system stops filling the tank and begins
to fill in HX Tank. After the level of the HX Tank reaches its designed value, the fill-up
process is stopped and begins to fill in the Upper Tank. However, Figure 5.25 shows the
tank’s level still increases after stopping and changing to fill in the next tank. From
Figure 5.25, it is obvious that before the pressurizer level L3 begins to increase, Upper
Tank level L1 increases a little bit and keeps stable. Before starting the filling procedure,
valve CV-13 is in NO (normal open) status. When the system begins to fill the first tank -
 90

Pressurizer, it sends an order to close CV-13. However, it takes time for CV-13 to close.
During this time, water is fed into the Upper Tank and, thus, its level increases until the
CV-13 closes as indicated in Figure 5.26. After the process switches to fill in the HX
Tank and valve CV-11 is requested to close, it takes time for CV-11 to close. Water is
still fed to Pressurizer and thus Pressurizer level L3 is still increasing, as indicated in
Figure 5.26

Figure 5.25 Tanks level change during start-up

 91

Figure 5.26 NPCTF system diagram during start-up

5.3 Safety Systems Evaluation

As described in chapter 2, this DCS system implements three safety systems: Shut-down
System Number 1 (SDS1), Shut-down System Number 2 (SDS2), and Emergency Core
Cooling (ECC). This section evaluates these three safety systems.

5.3.1 Shut-down System Number 1 (SDS1)

As discussed in Chapter 2, SDS1 can be activated when RELAY_A (R-A in Figure 5.28)
and RELAY_A (R-A in Figure 5.28) are all activated, and RELAY_A and REALY_B all
can be activated by the average temperature of the Heater outlet, T2. SDS1 function is
tested by increasing the average temperature of T2 to 32 (℃) and 34 (℃) to activate
 92

RELAY_A and RELAY B, respectively. When the average temperature of T2 reaches 32

(℃), the RELAY_A (R-A in Figure 5.28) icon turns red, as shown in Figure 5.28. When
T2 arrives at 34 at 10:45:54AM, as shown in Figure 5.27, RELAY_B (R-B in Figure 5.28)
is activated and the corresponding icon becomes red, as shown in Figure 5.28. At this
time, the condition of SDS1 is satisfied and activated to trip the Heater, and the SDS1
icon becomes red and the Heater icon turns grey, as shown in Figure 5.28. “SAFETY”
and time of “10:45:54AM” are also shown at the bottom of Figure 5.28. The Alarm of
“SAFETY/SDS1_ALARM” shows the time of “10:45:54AM”, as shown in Figure 5.29.
Therefore, the HMI can indicate the alarm of SDS1 and the system activates to stop the
Heater when condition of SDS1 is satisfied. Other conditions that can trigger relays of A,
B, and C are listed in appendix C.

Figure 5.27 T2 average curves for SDS1

 93

Figure 5.28 NPCTF system diagram for SDS1

Figure 5.29 Alarm of SDS1

 94

5.3.2 Shut-down System Number 2 (SDS2)

Water primary pressure P1 is used to test SDS2 function. Since the maximum pressure
after the regulator is 18psig, 17psig is used to test the SDS2 function. Increase the
primary water pressure P1 to reach 17psig to activate SDS2. From Figure 5.30, the
primary pressure reaches 17psig at 9:01:54AM. In Figure 5.31, HMI shows there is a
“SAFETY” alarm at 9:01:54AM at the bottom, the SDS2 icon becomes red and the
Heater becomes grey. The alarm of “SAFETY/SDS2_ALARM” at 9:01:54AM is shown
in Figure 5.32. Therefore, when the SDS2 condition is satisfied, the HMI indicates the
alarm and related action is taken. The Other conditions to trigger SDS2 are listed in
appendix C.

Figure 5.30 Primary water pressure P1 curve for SDS2

 95

Figure 5.31 NPCTF system diagram for SDS2

Figure Alarm of SDS2

Figure 5.32 Alarm of SDS2

 96

5.3.3 Emergency Core Cooling (ECC)

As discussed in section 2.4.3, ECC is activated by two conditions: either SDS1 or SDS2
and Pump 1 off. Therefore, ECC is tested by increasing primary pressure P1 to 17psig to
activate SDS2 and stopping Pump 1. The pressure P1 reaches 17psig at around
11:08:12AM, as shown in Figure 5.33. This condition can activate SDS1. In fact, there is
a “SAFETY” alarm at the bottom of the HMI, as shown in Figure 5.34. Detail of the
alarm is shown in Figure 5.35 as “SAFETY/SDS2_ALARM” at the same time of
11:08:12AM. At 11:08:15AM another condition is met by stopping Pump1. When the
two conditions of ECC are satisfied at 11:08:15AM, the alarm of ECC is activated. The
alarm is shown in Figure 5.34 as “SAFETY,” and in Figure 5.35 as
“SAFETY/ECC_ALARM” at 11:08:15AM. When both conditions are met, the system
acts to shut off the Heater which becomes grey and cools the Heater by opening valves
CV-19 and CV-20, and closing valves CV-15, CV-1, and CV-2. As shown in Figure 5.34,
the color of valves CV-19 and CV-20 becomes red and that of valves CV-15, CV-1, and
CV-2 becomes green. When valves CV-19 and CV-20 open, and valves CV-15, CV-1,
and CV-2 close, water flows from the Upper Tank to the Heater and goes back to the
Lower Tank by natural circling, as shown in Figure 5.34 as a red line.
 97

Figure 5.33 Primary water pressure P1 for ECC

 98

Figure Primary water pressure P1 curve

Figure 5.34 NPCTF system diagram for ECC

Figure 5.35 Alarms of ECC and SDS2

 99

5.4 Operation Modes Evaluation

5.4.1 Normal mode evaluation
Under Normal mode, the primary water pressure P1 is controlled by the Pressurizer as
well, as shown in Figure 5.36. Therefore, when the pushbutton “CLOSE WITH
PRESSURIZER”, on the right side of Figure 5.36 is pressed, the Normal mode is selected.
The control valve CV-11 is open to let the Pressurizer control the pressure of the system.
Meanwhile, CV-3 and CV-13 are closed and CV-14 is opened to build the cycling loop.
In Figure 5.36, CV-3 and CV-13 are shown in green which illustrates that the valves are
closed and CV-11 and CV-14 are shown as red which indicates the valves are open.

Figure 5.36 NPCTF system diagram during “Close With Pressurizer Mode”
 100

5.4.2 Solid mode evaluation

Under Solid mode, the Pressurizer is isolated and the cooling water pressure is controlled
by “feed and bleed”. Under Solid mode in NPCTF, the primary water pressure P1 is
controlled by valve CV-16 which functions as the “feed” to increase the water inventory,
and CV-13 which functions as the “bleed” to decrease the inventory. As shown in Figure
5.37, when the “CLOSE WITHOUT PRESSURIZER” button is pressed, the Solid mode
is selected. CV-11 is closed to isolate the Pressurizer. CV-13 and CV-3 are closed and
CV-14 is open to build the cycling loop. In Figure 5.37, CV-11, CV-3, and CV-13 are
green to indicate close status and CV-14 is red to show open status. The water pressure
P1 is controlled by CV-16 and CV-13.

Figure 5.37 NPCTF system diagram during “Close Without Pressurizer Mode”
 101

5.4.3 Open mode evaluation

When the “Open Mode” button is pushed, as indicated in the right side of Figure 5.38, the
operation of Open mode is selected. Under Open mode, CV-3 and CV-13 are open, and
CV-11 and CV-14 are closed. As indicated in Figure 5.38, CV-3 and CV-13 becomes red
to indicate an open status and CV-11 and CV-14 becomes green show closed status.

Figure 5.38 NPCTF system diagram during “Open Mode”

 102

5.5 Summary
In summary, the implemented four control functions on NPCTF are evaluated in this
Chapter, including process control, sequence control, safety systems and operation modes,
which are designed in Chapters 3 and 4. From the evaluation results shown above, it can
be concluded that the DeltaV DCS can perform all of these functions.
 103

Chapter 6
Conclusions
This thesis focuses on the programming and implementation of a DCS platform for
NPCTF. The main functions of this NPCTF are discussed. The functions are also
presented in logic diagrams. These functions are implemented in DCS system. Therefore,
a popular industrial DCS system, DelatV, is designed and built to operate the NPCTF.
The DelatV is setup and configured. Programming architecture is designed to organize
these functions under one “plant” in DCS. Industrial languages are used to program the
algorithm of these functions. HMI is created to operate and monitor the NPCTF. The SG
Tank level control loop is selected to demonstrate the process of design, a controller
starting from the model, model analysis and controller design. Using the MATAB system
identification tool, the model of the SG Tank level control is created and analyzed. Then
the controller parameters are calculated from the model and applied to controller of
DeltaV DCS. The response in the NPCTF proves that the method of design of the
controller based on the model can control the process. Response comparison between
MATLAB and NPCTF is similar. After the system is implemented, it is commissioned to
perform the functions.

The evaluation of the system concludes that this DeltaV DCS can implement the
functions of the NPCTF. When the designed safety conditions are satisfied, the safety
systems of SDS1 or SDS2 or ECC can perform designed actions, such as shut off heater.
For the process control, designed controllers can control the process variables through
manipulating related variables. Under start-up sequence control, the DCS operates to
satisfy the fill up requirement of pipes and tanks. The operator or researcher can select
the different operation modes to satisfy their requirements via HMI. Not only can HMI
supervise the process, observe and record parameter trends, but it can also operate the
NPCTF system and change the controllers’ parameters to satisfy the superficial research
requirements. In conclusion, the objective of the research is satisfied.
 104

6.1 Summary of Contributions

The major contributions of the research presented in this thesis have included the
following:

 The control system requirements of NPCTF are discussed. The requirements are
summarized as process control, safety systems, sequence control, and operation
modes. They are expressed in logic diagrams.

 An industrial DCS system, DeltaV, is selected to implement these requirements.

A cabinet which holds the DelatV hardware is designed and built. They are
connected to field devices with wires and to workstation through Ethernet. The
DelatV workstation and HMI is configured and setup to be able to communicate
with field devices and process variables can be monitored and be recorded.

 Programming architecture is designed to organize the requirements with the

principle of easy troubleshooting and understanding. All of the functions are
grouped under one “Plant”. Each process control loop, safety systems, sequential
control, operation modes and each type of I/O cards is organized under one
module respectively. Functions are programmed with industrial languages
prescribed under the standard of IEC 61131-3. The system is programmed with
the functions of safety operations which protect devices, and the system can stop
safety at anytime. HMI is created to supervise the process of NPCTF, force the
devices for purpose of research, and operate the system. The devices are indicated
as red when in operating mode, such as running pumps, and grey when stopped.
The pushbutton becomes brown when pushed. The valves are shown as red or if
open, green when closed and yellow when in the middle. Real value and history
values the process variables can be observed and recorded.

 The DeltaV system is commissioned for proper communication and correct

signals between field devices, PLC and workstation, HMI. The signals to and
 105

from field devices are calibrated to indicate the real device status. They are also
checked to be shown correctly in the HMI and workstation.

 The SG Tank level control process model is developed within operating range of
36% to 44% using the MATLAB system identification tool. The model is used to
analyze the stability of the process and design the controller parameters. The
parameters calculated from the model are applied to the NPCTF system. Its
responses prove that the controller designed from the model can control the
process within operating tange of 36% to 44%. Also, the SG Tank level control
system is compared between MATLAB and NPCTF and show that the response is
similar.

 Other process loops, except SG Tank level control, are tuned with the empirical
method to have as better responses as possible.

 The designed control system is evaluated to function as designed. To evaluate

three safety shutdown systems (SDS1, SDS2, ECC), the conditions which activate
the designed safety systems are created and actions are observed from HMI and
the NPCTF. The main purpose of the sequential control is fill up the pipes and
tanks and, thus, related valves and levels of the tanks can be observed the change
of status. Three operation modes are selected separately from HMI, and related
valves are observed to have corresponding changes. All process control loops,
except the SG Tank level control, are tuned with empirical method to have the
best possible performance.

6.2 Suggestions for Future Work

Based on the research, the following are the future subjects suggested for further research:

 Even though the current design of controllers can control the system, the
evaluation results show different characteristic responses at different operating
 106

points. Some loops, such as the Upper Tank level control, show more nonlinear
characteristic since the Upper Tank is designed as a nonlinear system. Nonlinear
controller or methods are suggested to control such processes.
 107

References
[1] G. L. Brooks, A Short History of the CANDU Nuclear Power System, January 1993.

[2] Ontario Power Generation, Unit Operational Control, pp. 136-138, April 1993.

[3] CANDU 6 Program Team, Candu 6 Technical Summary, pp. 62, June 2005.

[4] The Canadian Nuclear Industryand its Economic Contributions.

Accessed: March 5, 2015.
http://www.nrcan.gc.ca/energy/uranium-nuclear/7715

[5] CANDU Reactors Worldwide. Accessed: March 5, 2015.

http://teachnuclear.ca/all-things-nuclear/canadas-nuclear-history/candu-reactors-
worldwide/

[6] G. T. Bereznai, Nuclear Power Plant Systems and Operation, University of Ontario
Institute Technology, 2011.

[7] ANSI/ISA-S5.1-1984(R 1992), Instrumentation Symbols and Identification.

[8] K. Kant, Computer-Based Industrial Control, 2nd, PHI Learning Pvt. Ltd, 2013.

[9] S. K. Singh, Computer-Aided Process Control, PHI Learning Pvt. Ltd, 2004.

[10] D. Popovic and V. Bhatkar, Distributed Computer Control for Industrial

Automation, New York, 1990.

[11] T. Samad, “System architecture for process automation: Review and trends,”
Journal of Process Control, v 17, n 3, pp. 191-201, March 2007.

[12] S. K. Singh, Industrial Instrumentation and Control, 3rd, New Delhi, 2012.

[13] IDE Technologies, Practical Distributed Control Systems for Engineer and
Technician, Revision 6.1, 2012.

[14] L. F. Wang and K. C. Tan, Modern Industrial Automation Software Design, Wiley-
IEEE Press. Febuary 2006.

[15] M. Beharrell and R. Barillere, “OPC Evolution toward UNIX,” 10th ICALEPCS Int.
Conf. on Accelerator & Large Expt. Physics Control Systems. Geneva,
10-14 October, 2005.
[16] K. C. Kwon and M. Lee, “Technical Review on the Localized Digital
 108

Instrumentation and Control Systems,” Nuclear Engineering and Technology ,

Vol.41, No.4, May 2009.

[17] S. F. Gray and S. Basu, “Turbine Control System Upgrade for Bruce Nuclear Plant
Units 1 and 2,” IEEE International Conference on Electro/Information Technology,
June 2009.

[18] Combined Reliability-Centered Course for Instrumentation Professionals.

Accessed: March 5, 2015.
http://www.emersonprocessxperts.com/2014/06/combined-reliability-centered-
course-for- instrumentation-technicians/.

[19] History of PLC and DCS. Accessed: March 5, 2015.

http://www.control.lth.se/media/Education/DoctorateProgram/2012/
HistoryOfControl/Vanessa_Alfred_report.pdf.

[20] W. B. Dai, V. Vyatkin, and J. H. Christensen, “Essential Elements for Programming

of Distributed Automation and Control Systems,” IEEE 18th conference on
Emerging Technologies & Factory Automation (ETFA), 2013.

[21] IEC 61131-3, Programmable controllers - Part 3:Programming languages.

International Standard, Second Edition, 2003.

[22] J. P. Morgan, Global Industrial Automation Market Review. Global Equity

Research, June 2010.

[23] M. Yang, et al., “A Human-Centered Approach based on Multilevel Flow Models

for Diagnosing Fault in Nuclear Power Plant,” Proceedings of ICAPP 2007, Nice,
France, May13-18, 2007.

[24] Worldwide DCS Market Shares (%) Source : ARC Advisory Group, 2013.

[25] CIES Research Group of UWO, Nuclear Power Control Test Facility (NPCTF) User
Manual, first draft, 2015.

[26] W. Boyes and L. O’Brien, “The Top 50 Automation Companies.” Control.

pp. 22-24, December 2009.

[27] J. P. Morgan, Global Industrial Automation, Global Equity Research, June 2010.

[28] DeltaV Books Online Version 8.4.

 109

[29] X. L. Cui and Z. C. Zhou, “The Algorithm of Translation between the Ladder
Language and the Sentence Table Language of PLC,” Microelectronics and
Computer, vol. 17, NO. I, pp. 26-30, 2000.

[30] Z. B. Zhu and D. B. Zhao, “Implementation of Ladder Diagram to STL in SoftPLC,”

Mechanical and electronic, NO. 12, pp. 61-64, 2008.

[31] R. Wareham, “Ladder Diagram and Sequential Function Chart Languages in

Programmable Controllers,” Programmable Control and Automation Technology
Conference and Exhibition, 1988. Conference Proceedings, Fourth Annual Canadian,
1988 , Page(s): 12A - 14/1-4.

[32] IDC Technologies, Practical Industrial Programming Using 61131-3 for PLCs,
2007.

[33] IEC 62138, 2004. Nuclear Power Plant – Instrumentation and Control Important for
Safety – Software Aspects for Computer-based Systems Performing Category
B or C Functions.

[34] K. H. John and M. Tiegelkamp, IEC 61131-3:Programming Industrial Automation

Systems, 2nd edition, New York, 2010.

[35] M. King, Process Control-A Practical Approach, John Wiley & Sons Ltd, UK, 2011.

[36] T. Liu and F. R. Gao, Industrial Process Identification and Control Design, Springer,
2012.

[37] L. Ljung, System Identification - Theory for the User, 2rd, Sweden,1999.

[38] R. C. Dorf and R. H. Bishop, Modern Control System, 12th ed, New Jersey,
Pearson, 2011.

[39] D. E. Seborg, T. F. Edgar, and D. A. Mellichanp. Process Dynamics and Control.

2nd ed., New York, Wiley, 2004.

[40] A. O'Dwyer, “A Summary of PI and PID Controller Tuning Rules for Processes with
Time Delay,” IFAC Workshop on Digital Control, pp. 175-180, Terrassa, Spain,
April 4-7, 2000.

[41] A. O’Dwyer, Handbook of PI and PID Controller Tuning Rules, 3rdedition, Imperial
College Press, London, 2009.
 110

[42] D. E. Rivera, M. Morari and S. Skogestad, “Internal Model Control.

4.PID Controller Design,” Ind. Eng. Chem. Res. , 25(1), pp. 252-265, 1986.

[43] I. L. Chien and P. S. Fruehauf, “Consider IMC Tuning to Improve Controller

Performance,” Chem. Eng. Prog. , 86, pp. 33-41, 1990.

[44] I. G. Horn, J. R. Arulandu, J. Gombas, J. G. VanAntwerp and R. D. Braatz,

“Improved Filter Design in Internal Model Control,” Ind. Eng. Chem. Res. , 35(10),
pp. 3437-3441, 1996.

[45] S. Skogestad, “Probably the Best Simple PID Tuning Rules in the World,” Journal
of Process control , September 12, 2001.

[46] C. A. Smith and A. B. Corripio, Principles and Practice of Automatic Process

Control, John Wiley & Son, Inc., New York, 1985.

[47] C. L. Smith, Practical Process Control-Tuning and Troubleshooting, John Wiley &
Son, Inc., US, 2009.

[48] W. S. Levine, The Control Handbook, CRC Press, 1999.

[49] ANSI/ISA-5.1-2009, Instrumentation Symbols and Identification.

 111

Appendices
A. List of I/O (input/output) signals
Table A.1 lists all of the I/O signals to and from the field devices. There are four kinds of
I/O signals: analog input (AI), analog output (AO), digital input (DI) and digital output
(DO). For this NPCTF system, there are signals of 25 AI, 20 AO, 3 DI, 12 DO. They are
connected to DeltaV IO cards through terminals in a DCS junction box and DeltaV
cabinet. Table A.1 lists the terminal numbers in the DCS junction box and DeltaV cabinet,
and cable label of all the signals. For example, AI signal C1_I is connected to terminals 1
in DeltaV cabinet and terminal 1 in DCS JB. The cable that connects the signal is in cable
bundle labelled “DLTV1”.

Table A.1 List of I/O signals

TB# SGLs IO CBL # TB# SGLs IO CBL # DESC

DLV Cards DCS Type
JB

1 C1_I AI1 DLTV1 1 C1_I1 AI(18) DLTV1

3 C2_I 4 C1_I2

5 RMP_I 7 C2_I1

7 F1_I 10 C2_I2

9 F2_I 13 RMP_I1

11 F3_I 16 RMP_I2

13 F4_I 19 F1_I1
 112

15 L1_I 22 F1_I2

17 T4_I AI2 25 F2_I1

19 L3_I 28 F2_I2

21 L4_I 31 F3_I1

23 P1_I 34 F3_I2

25 P2_I DLTV2 37 F4_I1

27 P3_I 40 F4_I2

29 P4_I 43 L1_I1

31 T1_I 46 L1_I2

33 T2_1_I AI3 49 T4_I1

35 T2_2_I 52 T4_I2

37 T2_3_I 55 L3_I1

39 T3_I 58 L3_I2

41 T5_I 61 L4_I1

43 T6_I 64 L4_I2

45 T7_I 67 P1_I1

47 V1_I 70 P1_I2

49 CV1_I AI4 DLTV3 73 P2_I1 DLTV2

 113

65 C1_O AO1 76 P2_I2

67 C5_O 79 P3_I1

69 CV1_O 82 P3_I2

71 CV2_O 85 P4_I1

73 CV4_O 88 P4_I2

75 CV5_O 91 T1_I1

77 CV18_O 94 T1_I2

79 CV9_O 97 T2_1_I1

81 CV10_O AO2 100 T2_1_I2

83 CV13_O 103 T2_2_I1

85 CV16_O 106 T2_2_I2

87 CV17_O AO2 DLTV4 109 T2_3_I1 AI(6) DLTV2

89 CV19_O 112 T2_3_I2

91 CV21_O 115 T3_I1

93 CV34_O 118 T3_I2

95 CV15_O

97 CV25_O AO3

99 CV8_O 121 T5_I1

 114

101 CV12_O 124 T5_I2

103 C2_O 127 T6_I1

113 RCV1 DI 130 T6_I2

115 SDS1 133 T7_I1

117 SDS2 136 T7_I2

129 C1_C_D DO1 DLTV5 139 V1_I1

131 C5_C_D 142 V1_I2

133 CV_20_ 145 C1_O AO(3) DLTV3 pump1

D

135 CV_11_ 148 C5_O pump2

D

137 C2_C_D 151 CV1_O CV1

139 CC_1_D 154 CV1_I1 AI(1) DLTV3

141 CV_14_ 157 CV1_I2

D

143 CV_3_D 160 RCV1 DI(1) DLTV5 CV1

Relay
145 ROD DO2 162 RCV1
DOWN

147 DOWN 164 CV2_O AO(12) DLV3

 115

149 INTER 167 CV4_O

M

151 HOME 170 CV5_O

173 CV18_O

176 CV9_O

179 CV10_O

182 CV13_O

185 CV16_O

188 CV17_O DLTV4

191 CV19_O

194 CV21_O

197 CV34_O

200 CV15_O AO(5) DLTV4

203 CV25_O

206 CV8_O

209 CV12_O

248 C2_O heater

212 SDS1_1 DI(2) DLTV4 SDS

 116

214 SDS1_2

216 SDS2_1

218 SDS2_2

220 C1_C_D DO(12) DLTV5 Pump1

1

222 C5_C_D Pump2

1

224 CV_20_
D1

226 CV_11_
D1

228 C2_C_D Heater

1

230 CC_1_D Chiller

1

232

234

236 CV_14_
D1

238 CV_3_D
1
 117

240 ROD Linear

DOWN Motor
Relay
242 DOWN

244 INTERM

246 HOME
 118

B. Process control loops I/O

There are eleven process control loops and eleven variables to be adjusted to desired
values.
There are two actuators for the four loops, one for increasing the controlled variable and
another for decreasing the controlled variable. Table B.1 lists all of the process control
loops.

Table B. 1 Process control loops I/O

Loop Name Manipulated Controlled

Variables(u) Variables(y)

Primary water flow CV-1 F1(water flow)

Water heating C2 (heater power) T2(average

temperature)

HX outlet temperature CV-34(chilled flow) T3(temperature)

HX Tank pressure CV-21 P2 (pressure)

HX Tank level CV-25 L4(water level)

Pressurizer pressure CV-9(Main) P4 (pressure)

CV-10(Fixed)

Pressurizer water CV-12(Fixed) L3(water level )

level(water
CV-16(Main)
inventory)(close loop
with pressurizer)
 119

Upper Tank level CV-15(Fixed) L1 (water level)

CV-17(Main)

Water pressure(close CV-16(Main) P1(pressure )

loop without
CV-13(Fixed)
pressurizer)(no control
for open loop)

Air pressure CV-4 P3(pressure)

Air flow CV-8 F2(flow)

 120

C. Safety Systems Logic Diagrams

HTR T2 > 39
Relay A

HX tank L4 < 25

HX tank L4 >101

HTR T2 > 41
Relay B

HX tank L4 < 23

HX tank L4 >103

HTR T2 > 43
Relay C

HX tank L4 < 20

HX tank L4 >105

Figure C.1 SDS1 relays conditions

HX tank L4 >108

SDS2
HTR T2 > 45 Shut off HTR

WTR P1 > 20psig

Figure C.2 SDS2 conditions

 121

D. Programs of NPCTF in DeltaV DCS system

The whole control strategy is created using an engineering tool called DeltaV Explorer.
The whole system named “PCTF_SIMON”, as shown in Figure D.1, is created under
Control Strategies. There are twenty modules developed for the NPCTF system, as
illustrated in Figure D.1. For the process control loops, the last alphabet of the module
name after the underscore denotes the controlled parameter. For example, the module of
AIR_P contains the control strategy to control the pressure of air. Modules of
ANOLOG_INPUT, ANOLOG_OUTPUT, DISCRETE_INPUT, and
DISCRETE_OUTPUT include all the IO signals. The module of OPERATION_MODE
covers all the algorithms of three operation modes, i.e. Normal, Solid and Open mode.
There are two ratio algorithms under the RATIO module. The SAFETY module includes
the logic of SDS1, SDS2, ECC, and the safety protection of the Heater. The SEQUENCE
module is programmed using SFC industry language and includes the procedure logic to
start the system. The STOP_SYSTEM module is also created using SFC language and
includes the logic to put the system in safety status. All the pumps, heaters, and motors
are stopped and valves are pushed to normal status.

Each module includes different kinds of algorithm, such as function blocks or SFC
(Sequential Function Chart). Figures D.2 to D.135 show the detail algorithm of each
module. PID tuning parameters for each PID are also included in the figures of each
module.
 122

D.1 Control Modules

Figure D.1 Control modules

D.2 Air Flow

Figure D.2 Air flow control

 123

Figure D.3 PID tuning parameters

D.3 Air Pressure

Figure D.4 Air pressure control

 124

Figure D.5 PID tuning parameters

 125

D.4 Analog Inputs

Figure D.6 Analog inputs

 126

D.5 Analog Outputs

Figure D.7 Analog outputs

 127

D.6 Digital Inputs

Figure D.8 Digital inputs

 128

D.7 Digital Outputs

Figure D.9 Digital outputs

 129

D.8 HX_OUTLET_T

Figure D.10 HX tank outlet temperature control

Figure D.11 PID tuning parameters

 130

Figure D.12 SCLRS function block Figure D.13 LIM1 function block
 131

D.9 Operation Mode

Figure D.14 Operation mode control

 132

Figure D.15 Operation mode control parameters

D.9.1 Normal mode

Figure D.16 STARTUP_DONE function block

Figure D.17 RESET_AO_MODE function block

 133

Figure D.18 RESET_OTHERS1 function block

Figure D.19 VALVES function block

Figure D.20 PID_MODE1 function block

D.9.2 Solid mode

Figure D.21 RESET_OTHERS2 function block

 134

Figure D.22 VALVES1 function block

Figure D.23 PID_MODE2 function block

D.9.3 Open mode

Figure D.24 ACT3 function block

Figure D.25 RESET_OTHERS function block

Figure D.26 VALVES2 function block

 135

Figure D.27 PID_MODE function block

D.9.4 Mode selected

Figure D.28 MODE_SELECTED function block

Figure D.29 ACT1 function block

D.9.5 Run

Figure D.30 PUMP1 function block

Figure D.31 PID_CV2_MODE function block

 136

Figure D.32 CV13_MODE function block

D.9.6 Reset mode

Figure D.33 RESET_OTHERS4 function block

Figure D.34 CV13_MODE1 function block

Figure D.35 CV15_CLOSE function block

 137

D.10 Pressurizer Water Level

Figure D.36 Pressurizer level control

Figure D.37 PID_IN_CV16 tuning parameters

 138

Figure D.38 PID_DE_CV12 tuning parameters

Figure D.39 CND1 function block

Figure D.40 SP function block

Figure D.41 LIM1 function block

 139

Figure D.42 CALC1 function block

D.11 Pressurizer Pressure

Figure D.43 Pressurizer pressure control

 140

Figure D.44 PID_IN_CV9 tuning parameters

Figure D.45 PID_DE_CV10 tuning parameters

Figure D.46 SP function block

 141

Figure D.47 CND1 function block

Figure D.48 LIM1 function block

Figure D.49 CALC2 function block

 142

D.12 Primary Water Flow

Figure D 50 Primary water flow control

Figure D.51 PID_CV1 tuning parameters

 143

Figure D.52 PID_CV2 tuning parameters

Figure D.53 SP function block

Figure D.54 SCLRs function block

Figure D.55 CALC1 function block

 144

D.13 Ratio

Figure D.56 Ratio control

Figure D.57 RATIO_CV18 function block

Figure D.58 SCLR1 function block Figure D.59 SCLR3 function block

Figure D.60 RATIO_L4 function block

 145

Figure D.61 SCLR2 function block

D.14 Safety

Figure D.62 Safety control

Figure D.63 RELAY A function block

 146

Figure D.64 RELAY B function block

Figure D.65 RELAY C function block

Figure D.66 SHUT_HTR function block

Figure D.67 SDS2 function block

Figure D.68 ECCS function block

 147

Figure D.69 VALVES function block

Figure D.70 LIM1 function block

Figure D.71 ROD_DOWN function block

Figure D.72 ROD_DOWN1 function block

Figure D.73 ROD_DOWN2 function block

 148

D.15 Sequence

Figure D.72 Sequence control

 149

Figure D.73 STOP_AND_WAIT function block

Figure D.74 WAIT_UNTIL_INIT function block

Figure D.75 PID_MODE function block

 150

Figure D.76 INITIATION_MODE function block

 151

Figure D.77 INITIATION function block

Figure D.78 WAIT_3S1 function block

Figure D.79.1 OPEN_CV16 function block

 152

Figure D.79.2 OPEN_CV16 function block

Figure D.80 WAIT_CV16_OPEN function block

Figure D.81 CHRG_PRESSURIZER function block

Figure D.82 L3_OPEN_CV14 function block

 153

Figure D.83 OPEN_CV14 function block

Figure D.84 L3_DONE function block

Figure D.85 CHRGE_PRE_DONE function block

Figure D.86 WAIT_2S function block

Figure D.87 CHRGE_HX_TANK function block

Figure D.88 L4_DONE function block

 154

Figure D.89 CHRGE_HX_DONE function block

Figure D.90 WAIT_3S function block

Figure D.91 CHRGE_UP_TANK function block

Figure D.92 L1_DONE function block

Figure D.93 CHRGE_UP_DONE function block

 155

Figure D.94 WAIT_5S function block

D.16 HX Tank Level

Figure D.95 HX tank level control

Figure D.96 PID tuning parameters

 156

D.17 HX Tank Pressure

Figure D.97 HX tank pressure control

Figure D.98 PID tuning parameters

 157

Figure D.99 PID_AUTO function block

Figure D.100 CV5 function block

 158

D.18 Stop System

Figure D.101 Stop system control

 159

Figure D.102 Parameters

Figure D.103 S1 function block Figure D.104 T1 function block

Figure D.105 PID_MODE function block

 160

Figure D.106 T3 function block Figure D.107 CLOSE_CV18 function block

Figure D.108 INITIATION_MODE function block

 161

Figure D.109 INITIATION function block

Figure D.110 STOP_SEQUENCE function block

Figure D.111 WAIT_2S1 function block

 162

Figure D.112 RESET_SEQUENCE function block

Figure D.113 WAIT_2S function block

Figure D.114 START_SEQUENCE function block

Figure D.115 RESET_RUN function block

Figure D.116 RESET_OPER_MODE function block

 163

Figure D.117 RESET_RATIO function block Figure D.118 T2 function block

D.19 Upper Tank Level

Figure D.119 Upper tank level control

 164

Figure D.120 PID_CV17 tuning parameters

Figure D.121 PID_CV15 tuning parameters

Figure D.122 CND1 function block

 165

Figure D.123 SP function block

D.20 Water Heating

Figure D.124 Water heating control

Figure D.125 PID tuning parameters

 166

D.21 Water Inventory Pressure

Figure D.126 Water inventory pressure control

 167

Figure D.127 PID_CV16 tuning parameters

Figure D.128 PID_CV13 tuning parameters

Figure D.129 CND2 function block

 168

Figure D.130 CND1 function block

Figure D.131 SP function block

Figure D.132 LIM1 function block

Figure D.133 CALC3 function block

 169

Figure D.134 CALC2 function block

Figure D.135 CALC1 function block

 170

Curriculum Vitae
Name: Ximing Liu

Place of birth: Shantou, Guangdong, China

Year of birth: 1968

Post-secondary Master of Engineering Science
Education and Degrees: May 2012 – April 2015
Department of Electrical and Computer Engineering
The University of Western Ontario
London, Ontario, Canada

Graduate Diploma
1999-2001
International Law
Dalian Maritime University
Dalian, Liaoning, China

Bachelor of Engineering Science

1987 – 1991
Environmental Engineering
North China Electric Power University
Baoding, Hebei, China

Publication:

X. L. Liu and J. Jiang, “Control Strategies in Supercritical Fossil Power Plant and Related
Considerations for Canadian SCWR Power Plants,” The 6th International Symposium on
Supercritical Water-Cooled Reactors (ISSCWR-6), 2013, China.