Scribd
Upload
64 views1 page

Switch 9 Position A09 - Wiring Diagram

This document provides instructions for setting up sensors and inputs for ECUs using auxiliary voltage or temperature inputs. It describes how to configure a 9-position switch sensor by locking in the analog-to-digital values for each switch position. It also provides an example of setting up a fuel trim channel using a voltage input pin and calibrating it with a ratiometric 5V table.

Uploaded by

hamadalhosani666
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
64 views1 page

Switch 9 Position A09 - Wiring Diagram

This document provides instructions for setting up sensors and inputs for ECUs using auxiliary voltage or temperature inputs. It describes how to configure a 9-position switch sensor by locking in the analog-to-digital values for each switch position. It also provides an example of setting up a fuel trim channel using a voltage input pin and calibrating it with a ratiometric 5V table.

Uploaded by

hamadalhosani666
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Deutsch MT04-3P

M4 & M4-8 ECU


3 5V
2 Sig
1 0V 4
5V 5V
Sig Note 1
Note 1 0V 27
Use Aux Voltage ( Pin 18 ) or Aux Temp ( Pin30 ) 0V

Note 2
An Aux Voltage ( Pins 27A,13B, 16B ) or Aux Temp ( Pins7B, 8B,9B,14B,
15B ) can be used
M8 ECU

Note 3
Analog Voltage ( Pins 1,2,3,4,5,19,20,21,22,23, 24, 25,26, 45, 46,47,48, 1B,12A
49,50) or Analog Temp ( Pins 34,35,36,37,38,39,41,42 ) inputmay be used. 5V 5V
Sig Note 2
0V 2B,10A
ECU Sensor Setup 0V
1. In Sensor Setup menu, select a user defined scale ie -4.
2. In Sensor Cal Menu, select the AUX V or AUX T input pin the switch is wired to.
3. Turn switch fully counter clockwise lock in A/D value at lowest scale.
4. Rotate switch clockwise and lock in A/D value at next scale value. Repeat for all switch positions.
ADL

ADL Sensor Setup ( for Fuel Trim channel using voltage input pin )
1. Assign the Fuel Trim channel to the pin you have used. 18,28,44
2. In Calibration, select change. 5V 5V
3. Select Ratiometric(5V). Sig Note 3
4. In the calibration table enter: 0V 17,27,43
0V
VOLT 0.000 0.750 0.751 1.250 1.251 1.750 1.751 2.250 2.251 2.750 2.751 3.250 3.251 3.750 3.751 4.250 4.251 5.00
% -8.0 -8.0 -6.0 -6.0 -4.0 -4.0 -2.0 -2.0 0.0 0.0 2.0 2.0 4.0 4.0 6.0 6.0 8.0 8.0

Title 9 Position Switch #56100 Sheet No Drawing No

MoTeC Date 21/09/1999 Drawn ST App Products ADL, ECU 1 of 1 A09

You might also like