Scribd
Upload
30 views

Assignments

This document contains two assignments for an Analog Integrated Circuits course. The first assignment asks students to describe the function and characteristics of operational amplifiers, solve circuit analysis problems involving op-amps, and design various circuits using op-amps, including inverting amplifiers, non-inverting amplifiers, and filters. The second assignment involves analyzing timer circuits using the IC 555, comparing analog-to-digital conversion methods, designing passive filters, and analyzing voltage regulators and phase-locked loop circuits including calculations involving the PLL IC 565.

Uploaded by

Kavi Sanjai
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
30 views

Assignments

This document contains two assignments for an Analog Integrated Circuits course. The first assignment asks students to describe the function and characteristics of operational amplifiers, solve circuit analysis problems involving op-amps, and design various circuits using op-amps, including inverting amplifiers, non-inverting amplifiers, and filters. The second assignment involves analyzing timer circuits using the IC 555, comparing analog-to-digital conversion methods, designing passive filters, and analyzing voltage regulators and phase-locked loop circuits including calculations involving the PLL IC 565.

Uploaded by

Kavi Sanjai
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING

IV SEMESTER ACADEMIC YEAR: 2023-24


22LPC406 – ANALOG INTEGRATED CIRCUITS ASSIGNMENT – 1
Submission Date: 19.03.2024 Answer all questions Max.Marks:40
S.N Questions Bloo CO Ma
o ms rks
Level
Describe the function of operational amplifier internal stages with neat circuit
1 U CO1 10
diagrams. Explain the DC and AC characteristics of the op.amp.
(i) Determine the approximate value of resistor R1 through which reference
current will flow in Widlar current mirror when the circuit operated with
VCC =10V, VBE = 0.7 V, β = 125 and reference current of 1mA. (2
marks)
(ii) Determine the output voltage when V1 = –V2 = 1 V.

(2 marks)
(iii) An Op-Amp has an open loop gain of 105 and an open loop upper cut-
off frequency of 10 Hz. If this Op-Amp is connected as an amplifier with
2 a closed loop gain of 100, determine the new upper cut-off frequency. An CO1 10
(2 marks)
(iv) Calculate the input voltage if the final output is 10.08 V. (2 marks)

(v) A 741 Op.Amp is used as inverting amplifier with a gain of 100. The
frequency response of the amplifier is flat upto 50 KHz. What maximum
peak to peak input signal can be applied without distorting the output? (2
marks)

Design a circuit with appropriate assumption to execute the following functions


using Op.amp.
i) Amplifier with gain of -7.8 (2 marks)
ii) Amplifier to provide gain of 11 (2 marks)
3 iii) 3V1 + 4.5V2 - 6.6V3 (2 marks) Ap CO2 10
iv) Differentiate upto 1.1 KHz sine wave signal with Capacitor 1µF
(2 marks)
v) Integrate 3V peak sine wave at 5 kHz. (2 marks)

Derive output expression of log and antilog amplifiers using suitable circuit
4 U CO2 10
diagrams
DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
IV SEMESTER ACADEMIC YEAR: 2023-24
22LPC406 – ANALOG INTEGRATED CIRCUITS ASSIGNMENT – 2
Submission Date: 16.05.2024 Answer all questions Max.Marks:40
S.N Questions Blooms CO Marks
o Level
(i) Calculate the duty cycle of an astable multivibrator using
555 timer with RA=4.7kΩ, RB=1kΩ, C=1µF, C1=0.01µF (4
1 Ap CO3 10
marks)
(ii) Explain the applications of IC 555 Timer briefly (6 marks)
(i) Determine the time taken to convert 8 bit digital data into
analog voltage using SAR and Counter ADC with the clock
frequency of 1 KHz (2marks)
(ii) Design a first order band pass filter with an upper cut off
2 An CO4 10
frequency of 6 kHz and lower cut off frequency of 1 kHz.
(4 marks)
(iii) Design a second order low pass Butterworth filter for a cut-
off frequency of 10 kHz. (4 marks)
Describe the function of IC723 general purpose regulator under
3 U CO5 10
low and high voltage regulation using suitable circuits.
(i) List the basic building blocks of PLL. Analyze the closed
loop operation with suitable expressions. (6 marks)
(ii) Draw internal circuit of PLL IC565. Calculate free running
4 Ap CO5 10
frequency, lock range and capture range of PLL, if RT =
2.2KΩ, CT = 0.01µF, filter capacitor of 4.7µF and supply
voltage range ±6V. (4 marks)

You might also like