Technical Information

Flow Dividers and Gear Motors

1FDF / 1AFDF / 2FDF / 3FDF
1MF / 1AMF / 2MF / 2.5MF / 3MF / 3.5MF

www.grhpro.com
Keep the concept seeking excellence, GRH try our best
to create more value for you with products and service.
01

Guorui Hydraulics
About GRH
GRH was established in 1986, focusing on providing customers with quality hydraulic
components and solutions to hydraulic system in the applications of engineering machinery,
mobile industries, agricultural machinery, aviation, mining, and other fields. Main products
include gear pump, gear motor, flow divider, orbital motor, load sensing proportional valve,
monoblock valve, sectional valve, manifold assembly and hydraulic power unit as well.

Long-term development strategy

Reducing emissions by new energy is one of GRH's long-term strategies. GRH will be
providing innovative technologies, products, and services for the global development of
new energy, moving towards a century development strategy, and writing a century-new
chapter in the hydraulic field.

grhpro.com
 02

Innovation leads the future

Through a few decades of development, GRH has built an intelligent manufactur-
ing factory, gathering international R&D talents, accumulating rich R&D and man-
ufacturing experience, possessing independent intellectual property rights,
continuously providing customers with new products and technologies, and
creating value for all of the customers.

grhpro.com
03

Flow Dividers and Gear Motors

04-08 Flow Dividers

Gear Motors 10-23

Flow Dividers

04 Introduction of Flow Dividers

Ordering Code 04

05 1FDF Flow Dividers

1AFDF Flow Dividers 06

07 2FDF Flow Dividers

3FDF Flow Dividers 08

grhpro.com
 Gear Motors Flow Dividers 04

Introduction of Flow Dividers

Two or several gear motors can be combined into flow divider after being connected by coupling. It guatan-
tees synchronous operation and accuracy of power element like cylinder (Its principle drawing is as follows),
hydraulic liquid from the pipe is input into the inlet port and the same amount liquid is distributed to the
outlet port by the rotation of gears that with same specification. Obviously, accuracy of flow divider is up to
accuracy of gears and relative spare parts.
GRH has three series for flow divider 1FDF, 2FDF, 3FDF. Flow accuracy and pressure loss are as follows:

Type Flow Accuracy Pressure Drop

1FDF ±1.5%-±2% 16-19bar

2FDF ±1.5%-±2% 11-14bar

3FDF ±1.5%-±2% 11-14bar

It should be noted that flow accuracy is also related to the factors below: system pressure, viscosity of
hydraulic liquid, load that each function unit bears and overall flow. These factors should be taken into
account at time of application.
Flow divider can be integrated with relief valve, check valve and throttle valve, protecting system pressure
and filling the oil. For specific requirements, please contact GRH.

Outlet1 Outlet2 Outlet3 Outlet4

Inlet

Ordering Code

３ FD F 60 L71 -4 -1
a b c d e f ｇ

ⓐ Model: Group 1, 2, 3 ⓔ Inlet/Outlet Combination

ⓑ Function: Flow Divider ⓕ Number of Section: 1-8
ⓒ Pressure Level: 16-25Mpa ⓖ Number of Inlet: 1-4
ⓓ Displacement: 1.6-70ml/r

grhpro.com
05 Flow Dividers Gear Motors

1FDF**L**-2/4 Flow Dividers

Displacement Speed Flowrange/Section Min. system pressure Max. pressure of oil outlet
in³/r ml/r min. (rpm) max. (rpm) gpm lpm psi bar psi bar
0.097 1.6 0.42 1.25 1.6 6.72 3480 240
0.122 2 0.52 2.2 2 8.4 870 60 3480 240
0.195 3.2 3000 0.84 3.52 3.2 13.44 3480 240
0.244 4 1.05 4.41 4 16.8 3480 240
1000
0.305 5 1.31 5.51 5 21 3480 240
0.366 6 1.57 5.51 6 21 580 40 3480 240
0.427 7 3500 1.84 6.43 7 24.5 3480 240
0.488 8 2.10 7.34 8 28 3480 240

Dimensions

Schematic Diagrams
OUT1 OUT2 OUT1 OUT2 OUT3 OUT4

IN IN

grhpro.com
 Gear Motors Flow Dividers 06

1AFDF**L**-Y-V Flow Dividers

Displacement Speed Flow range/Section Min. system pressure Max. pressure of oil outlet
in³/r ml/r min. (rpm) max. (rpm) gpm lpm psi bar psi bar
0.103 1.7 0.35 1.33 1.36 5.1 3480 240
0.122 2 0.42 1.57 1.6 6 3480 240
0.146 2.4 0.5 1.88 1.92 7.2 1160 80 3480 240
0.164 2.7 0.56 2.12 2.16 8.1 3480 240
0.183 3 0.63 2.36 2.4 9 3480 240
0.207 3.4 800 3000 0.71 2.68 2.72 10.2 3480 240
0.250 4.1 0.86 3.23 3.28 12.3 3480 240
0.311 5.1 1.07 4.01 4.08 15.3 3480 240
725 50
0.372 6.1 1.28 4.8 4.88 18.3 3480 240
0.433 7.1 1.49 5.59 5.68 21.3 3480 240
0.488 8 1.68 6.3 6.4 24 3480 240

Dimensions

Outlet

Inlet Inlet
Drain Port

Schematic Diagram

grhpro.com
07 Flow Dividers Gear Motors

2FDF**L**-2/4 Flow Dividers

Displacement Speed Flow range/Section Min.system pressure Max. pressure of oil outlet

in³/r ml/r min. (rpm) max. (rpm) gpm lpm psi bar psi bar
0.366 6 1.26 5.51 4.8 21 3625 250
0.488 8 1.68 7.34 6.4 28 1160 80 3625 250
3500
0.671 11 2.31 10.1 8.8 38.5 3625 250
0.732 12 2.52 11.02 9.6 42 3190 220
800
0.854 14 2.94 11.02 11.2 42 3190 220
3000
1.037 17 3.57 13.38 13.6 51 725 50 3190 220
1.525 25 5.25 16.39 20 62.5 3190 220
2500
1.891 31 6.51 20.33 24.8 77.5 2610 180

Dimensions

Drain Port

Schematic Diagrams

grhpro.com
 Flow
Gear Dividers
Motors Flow
GearDividers
Motors 08

3FDF**L**-*Flow Dividers

Displacement Speed Flow range/Section Min.system pressure Max.pressureof oil outlet

in³/r ml/r min. (rpm) max. (rpm) gpm lpm psi bar psi bar
1.22 20 4.2 13.12 16 50 3480 240
1.647 27 5.67 17.71 21.6 67.5 3480 240
870 60
1.83 30 6.3 19.67 24 75 3480 240
2.379 39 8.18 25.57 31.2 97.5 3480 240
800 2500
3.05 50 10.49 32.79 40 125 3480 240
3.355 55 11.54 36.07 44 137.5 3335 230
725 50
3.66 60 12.59 39.35 48 150 2900 200
4.27 70 14.69 45.9 56 175 2610 180

Dimensions

Outlet Outlet Outlet Outlet

Inlet Inlet

Schematic Diagrams

Outlet

Inlet

grhpro.com
09 Flow Dividers Gear Motors

Gear Motors

Introduction 10

12 Specifications

Ordering Code
13

1MF/1AMF Bi-direction
14

2MF Bi-direction
15

17 2.5MF/3MF Bi-direction

3.5MF Bi-direction 18

19 With Outboard Bearing

Load of Outboard Bearing 21

22-23 Performance Curves

grhpro.com
 Gear Motors Flow Dividers 10

Introduction of GRH Gear Motors

Gear motors from Guorui Hydraulics have a floating bushing feature with automatic axial clearance compensa-

tion. The bushings are made with special abrasion resistant material providing improved service life. Precisely

machined gears ensure the excellent characteristics under low noise condition. Our cold extrusion motor bodies

can endure pressure above 30 MPa. High strength cast iron front & rear covers also enhance our reliability. Our

gear motors are widely used in the industrial, mobile, marine and aerospace industries.

GRH has 5 series of gear motors: group 1, 2, 2.5, 3 and 3.5. They can be divided into two types. One is the single

direction gear motor, the other is the bi-direction gear motors. Normally the design of the single direction gear

motor is similar to that of the single direction gear pump with some slight design differences. Therefore, every

GRH gear motor has the corresponding single direction gear motors. When placing your order, please refer to

the ordering code.

We now focus on the bi-direction gear motors. This motor has a different sealing structure to the single direction

motor. The symmetrical sealing (refer to the following drawing) separating high pressure from low pressure thus

allowing bi-direction operation. The oil from internal leakage returns to tank through the drain port. Normal case

drain pressure is limited to 2 bar, but 5 bar is allowed for intermittent operation. High quality of the bushings,

bearings and seals adds to the outstanding performance of GRH bi-direction gear motors.

Drain

Characteristics
Direction of rotation: bi-direction and single-direction
Permissible ambient temperature range: min. -20°C - max. 60°C
Operating pressures: input side P1 max = refer above data; outlet side P2 max. 3 bar
Drain pressure: max. 2 bar, Short time: max. 5bar
Fluid temperature range: max. 90°C for NBR rotary shaft lip-type seal, 100°C for FKM rotary shaft lip-type seal
Viscosity range: min. 10mm2/s - max. 600mm2/s

grhpro.com
11 Flow Dividers Gear Motors

Filtration
Recommended Viscosity range: V= 30-45mm2/s
Recommended hydraulic fluids use: GB11118-94, L-HM46 or equate NFE-603/DIN515524 II-85
Characteristic curves refer to pages: page 22 to 23

Characteristics

Pressure
P≤2000PSI(14MPa) 2000PSI(14MPa)<P<3050PSI(21MPa) P≥3050PSI(21MPa)
Standard
NAS1638 10 9 8

ISO4406 19/16 18/15 17/14

Filter 25μm 20μm 10μm

All motor can be combined with relief valve, proportional valve, thermostatic valve.

Guidance for Use of the Curve

In most cases, with the data of torque output M at speed n, and to get the data of pressure difference Δp and the
required Input flow, for example:
①M = 40 Nm; ②n = 1000 rpm; the intersection of ① and ② is the motor operating point with; ③Δp = 123 bar;
④Q = 21.3 l/min

grhpro.com
 Gear Motors Flow Dividers 12

Specifications

Pressure Speed
(bar) (r/min) Volumetric Mechanical
Series Displacement Output Torque
Efficiency Efficiency
(ml/r) (%) (%) (N.m)
Rated Int. Peak Max. Min.

1MF 1.1 - 5.1 200 230 250 4000 650 2.97 - 13.8
90 85
1MF 5.1 - 8.5 200 230 250 3600 650 13.8 - 23
2MF 4-8 200 250 280 4000 600 2.97 - 13.8
2MF 8 - 15 200 250 280 3500 600 10.8 - 40.6
2MF 15 - 20 200 250 280 3000 600 85 40.6 - 54.1
92
2MF 20 - 26 200 250 280 2500 500 54.1 - 70.3
2MF 26 - 30 180 210 250 2000 500 63.3 - 73.1
2.5MF 10 - 20 200 230 250 3600 500 27.1 - 54.1
2.5MF 20 - 30 200 230 250 3000 500 92 85 54.1 - 81.2
2.5MF 30 - 40 180 210 250 3000 400 73.1 - 97.4
3MF 22 - 43 200 230 250 3000 400 60.3 - 117.7
3MF 43 - 70 200 230 250 2500 400 93 86 117.7 - 191.7
3MF 70 - 89 200 230 250 2200 400 191.7 - 243.7
3.5MF 52 - 73 170 200 210 3600 500 121.1 - 169.9
3.5MF 73 - 100 150 165 180 3000 500 93 86 149.9 - 205.4
3.5MF 100 - 115 120 130 140 2500 500 164.3 - 188.9

Calculated Formulas

Volumetric Mechanical Total

Displacement Flow Pressure Speed Power Torque
Efficiency Efficiency Efficiency

cm3/r l/min bar r/min kW N.m 90% 85% 80%

V Q △p n P M ηv ηm ηt

Q = V.n · 10-³/ηv
M = △p·V ·ηm / 62.83
P = 2π·n·M/ 60000

grhpro.com
13 Flow Dividers Gear Motors

Ordering Code

2 A M F 8 F06 T24 S7 B -BB -O -I -F

a b c d e f g h i j k l m

ⓐ 2=Group 2 ⓗ Flange combination

ⓑ Covers S7=Europe rectangle flange
A=Cast iron cover D9=SAE A flange
Omit=Aluminum cover D19=SAE A flange
ⓒ M=Gear motor D10=SAE A flange
ⓓ Continous operate pressure ⓘ Rotation direction
F=200bar B=Bi-direction
G=250bar L=CCW
ⓔ Motor displacement R=CW
4, 6, 8, 10, 12, 14, 16, 18, 20, 23, 25 ⓙ Inlet/Outlet position combination
ⓕ Inlet/Outlet combination BF=Back inlet and front outlet
F06=Inlet(Φ40/M8/Φ20) Outlet(Φ30/M6/Φ13) BB=Back inlet and back outlet
F85=Inlet(Φ35/M6/Φ15) Outlet(Φ35/M6/Φ15) BS=Back inlet and side outlet
F52=Inlet(Φ35/M6/Φ15) Outlet(Φ40/M6/Φ20) SB=Side inlet and back outlet
L04=Inlet(G1/2) Outlet(G1/2) SF=Side inlet and front outlet
L46=Inlet(G3/4) Outlet(G3/4) SS=Side inlet and side outlet
L76=Inlet(1-5/8-12UN-2B) Outlet(7/8-14UNF-2B) ⓚ Outboard bearing
ⓖ Drive shaft extension and flange combination O=Outboard bearing
T24=1: 8 shaft Omit=Without outboard bearing
S13=SAE 16/32 spline 9 tooth ⓛ Mode of drain
F32=5/8 key shaft SAE A flange I=Inner drain
S46=SAE 16/32 spline 11 tooth SAE A flange Omit=Outside drain
S35=SAE 16/32 spline 10 tooth ⓜ Seals
F36=3/4 key shaft F=FKM seal
Omit=NBR seal

grhpro.com
 Gear Motors Flow Dividers 14

1MF**L69T3S5-B

Displacement
1.1 1.6 2.1 2.7 3.2 3.7 4.2 4.8 5.8 6.5 8.0
(ml/r)
L1 33 35 36 37 38 39 40 41 43 44 47
L 75 78 79 81 83 85 87 89 93 95 101

1AMF**L**F16D2-B

Displacement
(ml/r) 1.3 2.0 2.7 3.4 4.1 5.1 6.1 6.5 7.0 7.5 8.5

L1 42 43 43 45 46 47.5 49 49.5 50 50.5 52

L 82 84 86 88 90 93 96 98 100 102 103

1DMF6.1LJ86F108S20B-BB

Displacement Working Pressure Max Speed Torque

Direction
(ml/r) (bar) (rpm) (Nm)
6.2 70 5000 5.78 Bi-direction

grhpro.com
15 Flow Dividers Gear Motors

2MF**L04F63D9-B-I
This motor is internal drain port structure. Two check valves guarantee its bi-directional fuction and have the oil
of internal leakage return to inlet port. The function symbols are as follows：

Displacement
4 6 8 10 12 14 16 18 20 23 25
(ml/r)

L1 44 45 47 48 50 51 53 55 56 58 60

L 96 98 102 104 108 108 114 117 120 123 128

2MF**F**S13D9-R-V
The motor is with the relief valve of which the highest working pressure is same as that of the motor inlet port.
The function symbols are as follows：

SAE 16/32-9T

Displacement
4 6 8 10 12 14 16 18 20 23 25
(ml/r)

L1 39 40 41 43 44 46 48 49 51 54 57

L 111 112 115 118 120 125 128 132 137 139 141

grhpro.com
 Gear Motors Flow Dividers 16

2MF**L04F63D9-B

Drain Port

Displacement
(ml/r) 4 6 8 10 12 14 16 18 20 23 25

L1 44 45 47 48 50 51 53 55 56 58 60
L 96 98 102 104 108 108 114 117 120 123 128

2MF**F**T24S7-B

Drain Port

Displacement 6 8 10 12 14 16 18 20 23 25
4
(ml/r)
L1 46 47 49 50 52 53 55 57 58 60 62
L 98 100 104 106 110 112 116 119 122 125 130

2MF**F**T20O8-B

Drain Port

Displacement
4 6 8 10 12 14 16 18 20 23 25
(ml/r)
L1 39 40 41 43 44 46 48 49 51 54 57
L 90 91 94 96.5 98.5 103.5 107 111 116 118 120

grhpro.com
17 Flow Dividers Gear Motors

2.5MF**L**F77D20-B

Displacement
(ml/r) 10 16 20 25 27 30 32 36 40

L1 44 45 60 62 63 65 66 68 70

L 96 98 125 130 132 137 139 144 148

3MF**L**T11S14-B

Drain Port

Displacement
22 26 34 39 43 51 60 70 78 89
(ml/r)
L1 64 66 68 70 71 74 77 81 83 87

L 129 132 137 141 144 150 156 163 168 174

3MF**L**S70D12-B

Drain Port

Displacement 22 26 34 39 43 51 60 70 78 89
(ml/r)
L1 66 67 69 71 73 76 79 82 85 88
L 131 134 139 143 147 152 158 166 171 176

grhpro.com
 Gear Motors Flow Dividers 18

3.5BMF**F108F102S13-B
Direction C

Displacement
(ml/r) 63 80 100
L1 119 125 132
L 215 221 228

3.5MF**L**S84D14-B

Displacement
(ml/r) 52 63 73 85 93 104 115

L1 181 188 194 200 207 213 219

L 207 216 225 235 244 255 264

3.5MF**L**S95D17-B

Displacement
52 63 73 85 93 104 115
(ml/r)
L1 181 188 194 200 207 213 219
L 207 216 225 235 244 255 264

grhpro.com
19 Flow Dividers Gear Motors

Outboard Bearing 2MF**F*****B-O

Coupling 2MF-C1

Dimensions

Drain Port

4x6.5x16

2MF**F**T37S9-B-O
Drain Port

O: Outboard bearing A

B: Bi–direction

Displacement
4 6 8 10 12 14 16 18 20 23 25
(ml/r)

L01 73 74 75 77 79 80 82 83 86 89 92

L0 123 124 127 130 133 137 141 143 147 153 157

L1 39 40 41 43 44 46 48 49 51 54 57

L 90 91 94 96.5 98.5 103.5 107 111 116 118 120

grhpro.com
 Gear Motors Flow Dividers 20

Outboard Bearing 2MF**L**F63D10-B-O

Coupling 2MF-C1

Drain Port

Drain Port

2MF**L**P36D10-B-O
O: Outboard bearing
B: Bi– direction

Displacement
4 6 8 10 12 14 16 18 20 23 25
(ml/r)

L01 79 80.5 82 84 86 80 88 90 91 94 95

L0 131 134 137 140 144 137 150 153 156 160 163

L1 39 40 41 43 44 46 48 49 51 54 57

L 90 91 94 96.5 98.5 103.5 107 111 116 118 120

grhpro.com
21 Flow Dividers Gear Motors

Load of Outboard Bearing

FO=0 N FO=200 N

L(mm) L(mm)

FO=400 N FO=600 N

L(mm) L(mm)

FO=800 N FO=900 N

L(mm) L(mm)

grhpro.com
 Gear Motors Flow Dividers 22

2MF6 Performance Curves

Output Torque(Nm)

Pressure Drop(bar)

speed n rpm
Input flow Q I/min

2MF8 Performance Curves

Output Torque(Nm)

Pressure Drop(bar)

speed n rpm
Input flow Q I/min

2MF11 Performance Curves

Output Torque(Nm)

Pressure Drop(bar)

speed n rpm
Input flow Q I/min

grhpro.com
23 Flow Dividers Gear Motors

2MF14 Performance Curves

Output Torque(Nm)

Pressure Drop(bar)

speed n rpm
Input flow Q I/min

2MF16 Performance Curves

Output Torque(Nm)

Pressure Drop(bar)

speed n rpm
Input flow Q I/min

2MF19 Performance Curves

Output Torque(Nm)

Pressure Drop(bar)

speed n rpm
Input flow Q I/min

grhpro.com
© GRH | 2023

Shanghai Guorui Hydraulic Technology Co., Ltd

Add. Room 2201-2202, 1717 North Sichuan Road, Add. 666 West Shuanghu Road, Hi-tech Zone,
Hongkou Shanghai, China Jianhu Yancheng, Jiangsu, China
P.C. 200080 P.C. 224700
Tel. +86-21-6218 3268 Tel. +86 0515-86316688 +86 400 188 1986
Mail. [email protected] Mail. [email protected]