The Natural Response of An RL Circuit

The First Lecture of Electrical Networks
1- The Natural Response of an RL Circuit

The natural response of an RL circuit can best be described in terms of the circuit shown in Fig. 1.
We assume that the independent current source generates a constant current of Is A, and that the
switch has been in a closed position for a long time. We define the phrase a long time more
accurately later in this section.
For now, it means that all currents and voltages have reached a constant value. Thus only constant,
or dc, currents can exist in the circuit just prior to the switch's being opened, and therefore the
inductor appears as a short circuit (Ldi/dt = 0) prior to the release of the stored energy.
Because the inductor appears as a short circuit, the voltage across the inductive branch is zero, and
there can be no current in either R0 or R. Therefore, all the source current Is appearing in the
inductive branch. Finding the natural response requires finding the voltage and current at
the terminals of the resistor after the switch has been opened, that is, after the source has been
disconnected and the inductor begins releasing energy. If we let t = 0 denote the instant when the
switch is opened, the problem becomes one of finding v(t) and i(t) for t ≥ 0.
For t ≥ 0, the circuit shown in Fig.1. reduces to the one shown in Fig. 2.
Fig.1.
Fig.2.
1
2- Deriving the Expression for the Current
To find i(i), we use Kirchhoff s voltage law to obtain an expression involving i, R, and L. Summing
the voltages around the closed loop gives:
where we use the passive sign convention. Equation 7.1 is known as a first order ordinary
differential equation, because it contains terms involving the ordinary derivative of the unknown,
that is, di/dt. The highest order derivative appearing in the equation is 1; hence the term first-order.
We can go one step further in describing this equation. The coefficients in the equation, R and L,
are constants; that is, they are not functions of either the dependent variable i or the independent
variable t. Thus the equation can also be described as an ordinary differential equation with constant
coefficients. To solve Eq. 1, we divide by L, transpose the term involving i to the right-hand side,
and then multiply both sides by a differential time dt. The result is :
Next, we recognize the left-hand side of Eq.2 as a differential change in the current i, that is, di. We
now divide through by i, getting:
We obtain an explicit expression for i as a function of f by integrating both sides of Eq.3. Using x
and y as variables of integration yields:
in which i(t0) is the current corresponding to time t0 and i(t) is the current corresponding to time t.
Here, t0 = 0. Therefore, carrying out the indicated integration gives:
2
Based on the definition of the natural logarithm,
Therefore, in the first instant after the switch has been opened, the current in the inductor remains
unchanged. If we use 0− to denote the time just prior to switching, and 0+ for the time immediately
following switching, then
The current response for the circuit shown in Fig 3
We derive the power dissipated in the resistor from any of the following expressions:
The energy delivered to the resistor during any interval of time after the switch has been opened is:
3
3- The Significance of the Time Constant
The coefficient of t—namely, R/L —determines the rate at which the current or voltage approaches
zero. The reciprocal of this ratio is the time constant of the circuit, denoted:
Using the time-constant concept, we write the expressions for current, voltage, power, and energy
as:
The time constant is an important parameter for first-order circuits, so mentioning several of its
characteristics is worthwhile. First, it is convenient to think of the time elapsed after switching in
terms of integral multiples of τ. Thus one time constant after the inductor has begun to release its
stored energy to the resistor, the current has been reduced to e−1, or approximately 0.37 of its initial
value.
4
Examples
Example (1)
Solve:
We are not given an initial condition for this example; however, at the t = t-0inductor acts as a
short thereby shorting also the 20 resistor.
5
6
Example (2)
Solve:
7
8

The Natural Response of An RL Circuit

Uploaded by

Copyright:

Available Formats

The Natural Response of An RL Circuit

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

The Natural Response of An RL Circuit

Uploaded by

Copyright:

Available Formats

The First Lecture of Electrical Networks

1- The Natural Response of an RL Circuit

the voltages around the closed loop gives:

The current response for the circuit shown in Fig 3

You might also like