LOG IN REGISTER SUBSCRIBE SHOP HELP 0 items Search

SOUND ON SOUND

NEWS FORUM MAGAZINE REVIEWS TECHNIQUES PEOPLE SOUND ADVICE MUSIC BUSINESS

HOME > TECHNIQUES >

An Introduction To Frequency Modulation

Synth Secrets
Synthesizers > Synthesis / Sound Design, Synth Secrets
By Gordon Reid Published April 2000

As explained last month, audio-frequency modulation of the amplitude of

a signal can be a powerful synthesis tool. The possibilities expand still further
when we consider what happens when you use one audio-frequency signal to
modulate the frequency of another...

How many people can claim to have

discovered an entirely new form of sound
In this Series
synthesis? John Chowning can. He did so by
accident while experimenting with different Synth Secrets: all 63 Parts on Sound On Sound site
types of vibrato at Stanford University in the What's In A Sound?
mid-'60s. Chowning found that when the The Physics Of Percussion
frequency of the modulating signal increased Modifiers & Controllers
beyond a certain point, the vibrato effect Of Filters & Phase Relationships
Further With Filters
disappeared from the modulated tone, and
Of Responses & Resonance
a complex new tone replaced the original.
Envelopes, Gates & Triggers
With hindsight, we can see that he had
More About Envelopes
stumbled upon what is now the most John Chowning (at the 2015 Vox Festival). Photo An Introduction To VCAs
common encoding technique used for public courtesy Histeria.
Modulation
radio transmission (hence 'FM' radio). But Amplitude Modulation
what made his discovery so serendipitous was that unlike radio engineers, who work at very An Introduction To Frequency Modulation
high frequencies, way above the limits of human hearing, Chowning was able to listen to More On Frequency Modulation
the modulated waveform. He quickly discovered that FM is a very powerful method of An Introduction To Additive Synthesis
synthesis and, in 1966, became the first person to compose and record a piece of music An Introduction To ESPs & Vocoders
using FM as the exclusive means of sound generation. From Sample & Hold To Sample-rate Converters
(1)
Chowning and his associates spent the next few years refining FM, and laid down a sound From Sample & Hold To Sample-rate Converters
mathematical and practical basis for the results they were achieving. Chowning then had (2)
the Stanford University Licensing Office approach a number of American manufacturers to Priorities & Triggers
see whether they would be interested in implementing it as a commercial method of Duophony
synthesis. At a time when the Minimoog and ARP Odyssey ruled, polysynths were but Introducing Polyphony
a twinkle in electronic engineers' eyes, and 4-bit microprocessors were state-of-the-art From Polyphony To Digital Synths
devices, none of the American manufacturers saw the potential of FM. So it was almost in From Springs, Plates & Buckets To Physical
Modelling
desperation that Stanford turned to Yamaha. An engineer named Mr. Ichimura was duly
Formant Synthesis
despatched to see Chowning, and the rest, as they say, is history.
Synthesizing Wind Instruments
Synthesizing Brass Instruments
As a direct consequence of Yamaha's amazing success throughout the '80s — the company
Brass Synthesis On A Minimoog
sold millions of FM synthesizers, organs and home keyboards — we now think of FM as an
Roland SH101 & ARP Axxe Brass Synthesis
exclusively digital process. But that is not the case. It is more practical to implement it in
Synthesizing Plucked Strings
digital form, but the theory of FM is just as applicable to analogue oscillators, as we shall
The Theoretical Acoustic Guitar Patch
see...
A Final Attempt To Synthesize Guitars
Synthesizing Percussion

Once More, A Little Maths Practical Percussion Synthesis: Timpani

Synthesizing Drums: The Bass Drum
Last month I explained Amplitude Modulation, and described some of the ways in which it Practical Bass Drum Synthesis
allows you to create new sounds. Let's recap a little. Equations 1 and 2 show two instances Synthesizing Drums: The Snare Drum
of the simplest waveform: a sine wave. The instantaneous amplitudes of the waveforms Practical Snare Drum Synthesis
(their levels at any given point in time, called 'A') are related to their gains (the maximum Analysing Metallic Percussion
Synthesizing Realistic Cymbals
amplitude reached in their cycles, called 'a'), their frequencies ('w') and time ('t'). And, as
Practical Cymbal Synthesis
before, the subscripts '1' and '2' denote waveform 1 and 2 respectively.
Synthesizing Bells
Synthesizing Cowbells & Claves
Synthesizing Pianos
Synthesizing Acoustic Pianos On The Roland JX10
Equation 1: A simple 'cosine' wave.
[Part 1]
Synthesizing Acoustic Pianos On The Roland JX10
[Part 2]
Synthesizing Acoustic Pianos On The Roland JX10
Equation 2: A second 'cosine' wave. [Part 3]
Synthesizing Strings: String Machines
If you refer back, you'll also remember that we defined the maximum amplitude of the first Synthesizing Strings: PWM & String Sounds
waveform as the gain of a VCA, and we modulated this using the second waveform, as Synthesizing Bowed Strings: The Violin Family
shown in Figure 1, below. Equation 3 shows how I wrote the mathematics that describes this Practical Bowed-string Synthesis
arrangement. Practical Bowed-string Synthesis (continued)
Articulation & Bowed-string Synthesis
Synthesizing Pan Pipes
Synthesizing Simple Flutes
Equation 3: The equation defining the output waveform from the VCA in Figure 1. Practical Flute Synthesis
Synthesizing Tonewheel Organs: Part 1
But now we're going to mix things up a bit. Instead of modulating the amplitude of the first Synthesizing Tonewheel Organs: Part 2
waveform, we're going to modulate its frequency. The block diagram that describes this is Synthesizing Hammond Organ Effects
deceptively simple, as I have shown in Figure 2. Similarly, the equation describing Synthesizing The Rest Of The Hammond Organ:
Frequency Modulation (Equation 4) looks no more fearsome than that describing Amplitude Part 1
Modulation. Indeed, if you look closely you can see that exactly the same terms are present Synthesizing The Rest Of The Hammond Organ:
in both, it's just that one of them (A2) has changed position. Part 2
From Analogue To Digital Effects
Creative Synthesis With Delays
More Creative Synthesis With Delays
Equation 4: The equation defining the output waveform from Oscillator 1 in Figure 2. The Secret Of The Big Red Button

If we now echo last month's article and substitute the full expression for A2 into Equation 4, SOS Competitions
we obtain Equation 5.
Win! Heritage Audio i73 PRO Edge

Equation 5: Another way of writing Equation 4.

At this point, you would be completely justified in running,

screaming, for the hills. Unlike last month's equations
(which we could interpret using no more than 'O'-level or
maybe 'A'-level maths) this one is a monster. Indeed, even
with a degree in mathematics, you would be hard pressed
to do much with it. You will, therefore, be delighted to
know that I'm not even going to try to solve the equation.
Unfortunately, that means that you will have to take many
of the following facts on trust. But hey... trust me, I once
lived with a doctor!

FM Is Simply Very Fast Vibrato...

Now let's jump back two months, and return to Part 10 of
Readers' Ads
Synth Secrets and the simple vibrato that I described in
VIEW ALL ADS CREATE FREE AD
that article. Figure 3 shows what happens to a waveform (a
'Carrier') whose frequency is being swept up and down by Figure 1: [top] Amplitude Modulation.
a source of modulation (a 'Modulator'). In this example, the Figure 2: [bottom] Frequency On the same subject
frequency of that Modulator is significantly lower than that Modulation.
The Secret Of The Big Red Button
of the Carrier. July 2004
More Creative Synthesis With Delays
Now let's ask ourselves what happens as we increase the June 2004
Modulator's frequency until it approaches, equals, or even Creative Synthesis With Delays
exceeds that of the Carrier. At some point, instead of May 2004
looking like a cyclical 'squeezing' and 'stretching' of the From Analogue To Digital Effects
Carrier waveform, the modulation will become a form of April 2004
distortion within the individual cycles of the Carrier Synthesizing The Rest Of The Hammond Organ:
waveform. To demonstrate this I have drawn an example Part 2
March 2004
using a very short segment of Carrier waveform — maybe
one-eighth of a cycle or thereabouts (Figure 4).
From the same manufacturer
Let's now apply a Modulator to this. In this example it will
Why I Love... Old Keyboard Mixers
have a low amplitude, but will be many times the
February 2024
frequency of the Carrier (see Figure 5) — since there are
How I Got That Sound: Howard Jones
more than seven cycles of modulation in Figure 5, which
January 2024
shows one-eighth of a Carrier cycle, this means that the
Yamaha CK61 & CK88
Modulator frequency is approximately 60 times that of the January 2024
Carrier. As you will appreciate, this sounds nothing like Yamaha DX7: The Birth Of FM Synthesis | Podcast
vibrato. But what does it sound like? Figure 3: [top] The effect of vibrato on December 2023
a triangle wave. Figure 4: [bottom] A
Yamaha DM3
short segment of a Carrier waveform.
December 2023
Side Bands, Side Bands Everywhere
If you refer back to Equation 5, you'll see that the equation SIGN UP TO
for A1 has two 'alien' terms within it: a2 and w2. These are, SOS NEWSLETTERS
of course, the gain (maximum amplitude) and the frequency
of the Modulator. So it's fair to assume that each of these
will have an affect on the nature of the modulated signal.
Let's look first at w2, and see what attribute of the output is
influenced by the Modulator's frequency.

John Chowning discovered that FM, like AM, generates side

bands — additional components, not necessarily
harmonically related to the frequency of the Carrier or
Modulator — in the frequency spectrum of the output
signal. (For an explanation of what side bands are, please
refer back to last month.) To see how frequency modulation
produces side bands, let's take an example of a sine wave
Carrier with frequency wc and a sine wave Modulator of
frequency wm. I have shown these in Figure 6 (right).
Figure 5: [top] Modulating the
So far, so good... However, whereas AM generates just two Carrier in Figure 4 with a high-
Latest SOS Videos
side bands (wc+ wm) and (wc- wm), FM produces a whole frequency, low-amplitude
Modulator. Figure 6: [bottom] A
series that we can express as follows:
Carrier and a Modulator.

Equation 6: The side-band frequencies, where wsb = the series of side-band frequencies,
wc = Carrier frequency, wm = Modulator frequency, and n = any integer (0, 1, 2, 3, 4, and
so on).

To put this in English: each side band lies at a frequency equal to the Carrier frequency plus
or minus an integer multiple of the Modulator frequency. Of course, since 'n' can take any AR Rahman & Firdaus Studios: A Scoring Stage For The 21st
integer value, in theory, applying frequency modulation to a signal produces an infinite Century
series of side bands. In the real world, however, no system has infinite bandwidth, and
analogue systems are limited to producing side bands within their finite bandwidth (see
later for more on bandwidth). Similarly, manufacturers of digital FM systems constrain the
mathematics to those values that they deem significant.

Fortunately, and despite this possible

complication, the simple formula in Equation
6 makes it easy to see where the side bands
are located. Given the Carrier and the
Modulator shown in Figure 6 (above), we can
show the side bands as shown in Figure 7.

Now, what about the amplitudes of these side

bands? OK, we now know that frequency
modulation generates side bands, and that Building A Library: Spitfire Audio's ABBEY ROAD
the Modulator's frequency determines where ORCHESTRA | Chapter 1
they lie. But what is the 'shape' of the
resulting spectrum? To answer this, we must
Figure 7: The positions of the side bands.
turn to the second attribute of the Modulator
— its gain, a2 — and introduce a new concept called the 'Modulation Index', or simply 'ß'
('beta').

To explain ß, I must again direct you to our example of simple

vibrato. Imagine a simple synthesizer patch in which the
amplitude of a modulation is modified by a VCA that is itself
controlled by a Control Voltage source (see Figure 8). Don't
forget that in this case, the Modulator frequency wm is very Fraser T Smith | Producing 'SET FIRE TO THE RAIN' by Adele
much lower than the Carrier frequency wc.

Consider the case where the gain of the VCA is zero. Clearly,
there will be no modulation, and the Carrier will produce
a simple, unmodified tone. Now let's increase the gain of the
VCA slightly. As you would expect, a gentle vibrato results,
much like that of the aforementioned guitarist or violinist. But
let's not stop here, and keep increasing the gain until the
Modulator is sweeping the Carrier over a wide range of
frequencies. At this point, a banshee wail or siren-type sound
results. What we learn from this is that the sound we hear is
not only determined by the frequency of the Modulator, but
also by its gain or maximum amplitude. Figure 8: [top] A simple
analogue FM (vibrato) patch.
Applying these ideas to audio-frequency FM, we must first Figure 9: [bottom] FM side
bands with low Modulation
define ß as the ratio of the Carrier's frequency sweep (the
Index.
amount by which the Carrier deviates from its unmodulated
frequency) divided by the Modulator frequency. We write this as follows:

Equation 7: The Modulation Index, where ß = the Modulation Index, (pronounced 'delta')
means "the change in...", wc = Carrier frequency, and wm = Modulator frequency.

Since the numerator of this expression (the bit 'above the line') is the change in the Carrier
frequency, this means that ß is directly related to the amplitude of the Modulator. Now, this
is the point at which things get a little weird, because for any given Modulator frequency, it
is the Modulation Index (and, therefore, the amplitude of the Modulator) that determines
the amplitude of each of the components in the spectrum of the output signal. No, I can't
demonstrate why this is so without invoking some of that scary maths I mentioned before,
but I can show you a couple of examples.

Let's take that case where the Modulation Index is low — say in the region of 0.1 or less. The
only significant side bands will be those closest to the Carrier frequency, and the result will
look similar to that we obtained last month using Amplitude Modulation (see Figure 9,
above). In contrast, if ß is significantly higher — say, in the region of 5 — we obtain a much
broader series of side bands, and a much more complex spectrum results (see Figure 10).

I have shown the first six side bands created by ß=5, but there are far more in the real
signal. What's more, you should note an interesting consequence of this value of ß: the
amplitude of the original Carrier frequency has diminished significantly. Indeed, there is
a value of ß that will cause it to disappear altogether!

Now look at Equation 7 again and you'll see that the

denominator (the bit 'below the line') is the frequency of the
Modulator. The consequences of this are very far-reaching.
Let's say that you have decided that the spectrum in
Figure 10 is the tone that you want, and that you want to be
able to play the sound up and down the keyboard in
conventional manner. This will require both the Carrier and
the Modulator to track the keyboard equally so that the
harmonic relationship between the spectral components
(the side bands) remains constant. But Equation 7
demonstrates that, as the Modulator frequency increases, ß
decreases. For example, if you play one octave higher, wm
doubles and ß is therefore halved. To avoid this change in
the spectrum, the Modulator amplitude must increase
proportionally — it must double — to keep ß constant. This
is not as much of a problem as it sounds, and Figure 11
shows the simplest way to achieve this.
Figure 10: [top] FM of the same
Mind you, this configuration is almost impossibly difficult to signals when the Modulation Index
is increased. Figure 11: [bottom]
calibrate perfectly, and the vagaries of analogue Keeping ß constant.
components ensure that it will, at best, be inconsistent. This
is the reason why FM is almost always implemented using digital technology.

FM Versus Analogue Filters

To move on, we need to talk about bandwidth for a moment. I first mentioned this concept
in regard to Equation 6, when I said that real-world systems could not handle a signal of
infinite bandwidth. So let's discuss what the real bandwidth of an FM'd signal might be.

For the purposes of this discussion, you could define the bandwidth as the range of
frequencies occupied by any given signal. So, for example, a precise sine wave of, say,
100Hz would have negligible bandwidth (it exists only at a specific frequency) whereas
a waveform with the same fundamental frequency plus one harmonic at 200Hz would
occupy 100Hz of bandwidth. Likewise, a signal occupying the range between 100Hz and
1500Hz would have a bandwidth of 1400Hz, and so on. Now let's apply this concept to the
output from an FM system.

Suppose that the Carrier is a sine wave of frequency 500Hz and the Modulator is a sine
wave of frequency 300Hz. Clearly, if you mixed these together using a simple audio mixer,
then using the simple definition above, the resulting signal would occupy a bandwidth of
200Hz.

Now let's configure the signals so that Amplitude Modulation occurs. From last month we
know that the resulting three components have frequencies of wc, wc+ wm, and wc- wm.
These frequencies are 500Hz, 200Hz, and 800Hz respectively, so the bandwidth of the
resulting signal — the 'spread' between the lowest and highest side bands — is 600Hz.

Now let's consider the bandwidth of an FM'd signal. Although theoretically infinite
(remember, the series of side bands is infinite) the Modulation Index will ensure that side
bands of higher 'n' are of negligible amplitude. This means that the bandwidth is, to all
intents and purposes, finite. Moreover, there is a 'rule-of-thumb' equation that gives us
a rough idea of the meaningful bandwidth of the output signal. I have shown this in
Equation 8.

Equation 8: The bandwidth of the modulated signal, where B = bandwidth, wm =

modulator frequency, and ß = Modulation Index.

Let's say that ß is very small. Then, in our example of a 500Hz Carrier and a 300Hz
Modulator, the bandwidth of the output will be equal to 2 x 300Hz x (1 + 0) = 600Hz. Thus, as
I stated earlier, for low values of ß the result is much like that obtained using Amplitude
Modulation.

But now let's suppose that ß=5. Then, in our example, the bandwidth of the output will be 2
x 300Hz x (1 + 5) = 3,600Hz. Clearly, high values of ß allow FM to create much more complex
signals with a much higher bandwidth than the other methods of making two signals
interact (see Figure 12, below). Note that this calculation also tells you that, in this example,
there are 24 discrete spectral components in the output. Unfortunately, you'll have to read
next month's Synth Secrets to find out why.

Now let's remind ourselves that, in simple subtractive

synthesis, changes in the volume of a sound are most often
 determined by a contour generator acting upon an amplifier.
Similarly, any changes in the tone of a sound are usually
determined by a contour generator acting upon the cutoff
frequency of a filter.

In an FM configuration, the volume of the sound is still

determined by the volume envelope of the audio signal
(which is, of course, the modulated Carrier), but you no
longer need a filter to modify the tone. This is because, for
any given Modulator frequency, the Modulator amplitude
determines the bandwidth of the output. You can create an
interesting demonstration of this using just seven synthesizer
modules patched together as shown in Figure 13.

As you can see, the amplitude of the output signal will

decrease as EG2 decreases the gain of VCA2 — so over time, Figure 12: [top] The bandwidths of
the output gets quieter and quieter. At the same time, the mixed and modulated signals.
maximum amplitude of the Modulator signal derived from Figure 13: [bottom] A simple
analogue FM synthesizer.
VCO1 will increase as EG1 increases the gain of VCA1. This
means that, as time passes, the Modulation Index increases, the bandwidth increases, and
the output gets brighter and brighter. This is in marked contrast to natural sounds, where
increased loudness almost always goes hand-in-hand with increased brightness.

You might think that there's nothing stopping you duplicating this effect using a filter, and
it's true that you can use a contour generator and a low-pass VCF to brighten a signal as
time passes. But that configuration would be quite incapable of recreating the complex
tonal changes that also occur in the FM'd tone — changes that you cannot reproduce using
conventional subtractive methods.

Summary
So let's summarise. Without solving the mathematics of FM, we can say the following two
things about the relationship between the Modulator and the output signal:

The number of significant spectral components and their amplitudes are determined by
the Modulation Index, which is proportional to the Modulator's amplitude; but inversely
proportional to the Modulator's frequency...

...and...

For any given Carrier frequency, the position of the spectral components is determined
by the Modulator's frequency alone.

Although the proof of these statements and the calculation of the side bands' amplitude
spectrum is a nightmare, the basics are easily understood. And, whether we perform FM
using an analogue synth or a digital one, these principles remain the same. So here's this
month's Synth Secret (which, as usual, is no secret at all):

Frequency Modulation is a powerful method of synthesis that is as relevant to analogue

synthesizers as it is to digital ones, and which is capable of generating sounds unobtainable by any
other method.

Next month, we'll take a closer look at some practical aspects of Frequency Modulation, and
introduce the idea of 'operators' — a common concept if you own a DX7 synthesizer, but
perhaps not one that you have encountered in analogue technology. We'll even take a look
at some basic FM programming on a modular analogue synth.

Until then...

Previous article Next article

New forum posts Active topics Recently active forums

Re: Monitoring frustration Small circuit ventilation Forum FAQs

Bod Recording: Gear & Techniques
Sampling from Record Player
Mixing, Mastering & Post Production 15 Mar 2024, 09:21 Mixing, Mastering & Post Production
S.O.S. Band - No Ones Gonna Love You (Kick Drum) New Products & Industry News
Re: Monitoring frustration
Arpangel Music Business
Bunker Samples fifth anniversary: New $1 Try-Pack and competition
Mixing, Mastering & Post Production 15 Mar 2024, 09:09 Mac Music
Boss release Katana:Go headphone amp Windows Music
Re: Fender Tone Master Pro
Monitoring frustration Apps & Other Computers/OS
Wonks
Guitar Technology
Guitar Technology 15 Mar 2024, 09:01
e-instruments announce feature updates and 50% OFF saleKeyboards
for IOS pianos
& Synthesis
Re: Monitoring frustration New studio website! DIY Electronics & Studio Design
Bob Bickerton Live Sound & Performance
Mixing, Mastering & Post Production 15 Mar 2024, 08:58 VSTBuzz: 70% off “PSP PianoVerb2” by PSP Audioware
Music Theory, Songwriting & Composition
Re: Pub Band - what's changed since 2020 Clarett 2Pre USB vs Audient iD14 sound qualities User Reviews
OneWorld Remote Collaboration
Live Sound & Performance 15 Mar 2024, 08:56 Self-Promotion
Feedback

Contact Us Cookie Policy Help Privacy Policy Terms of Use

All contents copyright © SOS Publications Group and/or its licensors, 1985-2024. All rights reserved.
The contents of this article are subject to worldwide copyright protection and reproduction in whole or part, whether mechanical or electronic, is expressly forbidden without the
prior written consent of the Publishers. Great care has been taken to ensure accuracy in the preparation of this article but neither Sound On Sound Limited nor the publishers can be
held responsible for its contents. The views expressed are those of the contributors and not necessarily those of the publishers.

Web site designed & maintained by PB Associates & SOS