Ball Scresw

Ball Scresw
●Material & Surface hardness
Materials and Surface hardness of SR series（Standardized Rolled Ball Screws）and SSR series（Standardized
Stainless Rolled Ball Screws）are as follows.
SR/SSR series Standardized Rolled Ball Screws
Products Material Heat treatment Surface hardness
Rolled Ball Screws with accuracy Ct7 and Ct10 are available in stock. It is suitable for low cost design.
SCM415 Carburizing
Rolled Ball Screws with end-journal machining are available for short delivery. Shaft： S55C Induction Hardening
Stainless Rolled Ball Screws are also available. SUJ2 Quench & Temper
Rolled Ball Screws（SR series） HRC58 or more
Nut：SCM415 Carburizing and Quenching

Shaft：SUS440C Induction hardening

●Combination of Shaft nominal dia. & Lead Unit：mm Stainless Rolled Ball Screws
HRC55 or more
（SSR series）
Lead
Nut：SUS440C Vacuum hardening
Shaft dia. 1 2 2.5 4 5 6 8 10 12 15 20

A247
4 A248 A249

5 A250 ●Lubrication
A251 SR series（Standardized Rolled Ball Screws）and SSR series（Standardized Stainless Rolled Ball Screws）
Standard products in stock SR/SSR series

Standard products in stock SR/SSR series

6 A252 A253 A254 A255 without end-journal machining are applied with anti-rust oil for rust prevention.
A281
A256 A258 Anti-rust oil does not have lubricating function so that please apply the Grease or lubrication oil when using the
8 A257 A259 A260 A261 A262 A263 A264 Ball Screws.
A282 A283
A265 If there is no specific instruction, KSS would recommend our original Grease（MSG No.2）as standard lubricant.
10 A266 A267 A268 A269 A270 A271 Please feel free to contact us.
A284
A272
12 A273 A274

14 A275 A276 ●Precision Rolled Ball Screws

High accuracy（JIS C5）can be produced by Rolled process, what we call Precision Rolled Ball Screws（PSR/
15 A277 A278 A279 PSRT series）. Please see page A319.

Note 1）The models marked red are available for Stainless Rolled Ball Screws.
Note 2）The numbers in a table：showing a page in this catalogue.

●Model number notation

●Others

SR 06 01 K ー 200 R 200 C7 End-journal configuration of SR series（Standardized Rolled Ball Screws）and SSR series（Standardized
stainless Rolled Ball Screws）are not standardized. When you request additional machining, please send us a
drawing with end-journal profile.
① ② ③ ④ ⑤ ⑥ ⑦ ⑧ Rolled Ball Screws with Integrated end-journal, which is bigger Bearing face than supported seat, are available
（SRT/SSRT series）as shown below.
①Rolled Ball Screws Series No. Please refer to page A285 or ask KSS.
SR：Rolled Ball Screws
SSR：Stainless Rolled Ball Screws
②Screw Shaft nominal diameter（mm）
③Lead（mm）
④Ball Nut type Flanged end-journal for Bearing seat.
None：Standard
K：Compact type
⑤Screw thread length （mm）
（R=Right-hand）
⑥Thread direction
（mm）
⑦Screw Shaft total length
⑧Accuracy grade（C7 or C10）

●Accuracy Grade & Axial play

Accuracy grade of SR series（Standardized Rolled Ball Screws）and SSR series（Standardized Stainless Rolled
Ball Screws）are based on Ct7 and Ct10（JIS B 1192-3）. According to accuracy grade, Axial play 0.020mm or less
（Ct7）and 0.050mm or less（Ct10） are in stock.

A245 A246
Ball Scresw

Ball Scresw
Standard products in stock SR series Standard products in stock SR series

SR0401 Shaft dia.φ4 Lead 1mm Ct7&Ct10 SR0401K Compact Nut

Shaft dia.φ4 Lead 1mm Ct7&Ct10

17 4-φ2.9 13
4-φ3.4
see below E-F see below E-F
4 （13）
30° 30° 30° 30° 3 （10）

−0.05
φ11 −0.10
E F E F

−0.05
φ9 −0.10
（φ3.95）
（φ3.85）
D 17 D 14

φ19
PC PC

φ23

C0
C0

.5
.5
（25） L1（Accuracy guaranteed area） （25） 13
Standard products in stock SR/SSR series

Standard products in stock SR/SSR series

15

L2 L1（Accuracy guaranteed area）

Unit：mm Unit：mm
Ball Screw Specifications Ball Screw Specifications

Ball size φ0.8 Ball size φ0.6

Number of thread 1 Number of thread 1

Thread direction Right Thread direction Right

Shaft root dia. φ3.3 Shaft root dia. φ3.4

Number of circuit 3.7×1 Number of circuit 1×3

Shaft S55C
Shaft, Nut material SCM415H Material
Nut SCM415H

Surface hardness HRC58∼62 Surface hardness HRC58∼

（Thread area） （Thread area）

Anti-rust treatment Anti-rust oil Anti-rust treatment Anti-rust oil

Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L1 L2
ep V300 Ca Coa ep V300 Ca Coa

SR0401-250R250C7 180 Ct7 200 250 ±0.03 ー 0.200 ∼0.020 SR0401K-100R100C7 80 Ct7 100 ー ±0.02 ー 0.080 ∼0.020
ー 560 790 ー 300 430
SR0401-250R250C10 180 Ct10 200 250 ±0.14 ー 0.400 ∼0.050 SR0401K-100R100C10 80 Ct10 100 ー ±0.07 ー 0.160 ∼0.050

Note）Please designate end-journal profile with your sketch. Note）Please designate end-journal profile with your sketch.

A247 A248
Ball Scresw

Ball Scresw
Standard products in stock SR series Standard products in stock SR series

SR0402 Shaft dia.φ4 Lead 2mm Ct7&Ct10 SR0504 Shaft dia.φ5 Lead 4mm Ct7&Ct10

19 22
4-φ3.4 4−φ3.4
see below E-F
4 （15） 4 （18）
see below E-F
30° 30° 30° 30°

−0.05
φ11 −0.10

−0.05
φ12 −0.10
E F

（φ3.85）

（φ4.85）
E F
PCD 17

φ23
18
PCD

φ24
C0
.5

C0
.5
Standard products in stock SR/SSR series

Standard products in stock SR/SSR series

15 （25） Ｌ1（Accuracy guaranteed area） （25）
16 （25） L1（Accuracy guaranteed area） （25）
L2
L2

Unit：mm Unit：mm
Ball Screw Specifications Ball Screw Specifications

Ball size φ0.8 Ball size φ0.8

Number of thread 1 Number of thread 1

Thread direction Right Thread direction Right

Shaft root dia. φ3.3 Shaft root dia. φ4.3

Number of circuit 2.7×1 Number of circuit 2.7×1

Shaft, Nut material SCM415H Shaft, Nut material SCM415H

Surface hardness HRC58∼62 Surface hardness HRC58∼62

（Thread area） （Thread area）

Anti-rust treatment Anti-rust oil Anti-rust treatment Anti-rust oil

Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L1 L2
ep V300 Ca Coa ep V300 Ca Coa

SR0402-250R250C7 180 Ct7 200 250 ±0.03 ー 0.200 ∼0.020 SR0504-250R250C7 175 Ct7 200 250 ±0.03 ー 0.120 ∼0.020
ー 420 570 ー 470 720
SR0402-250R250C10 180 Ct10 200 250 ±0.14 ー 0.400 ∼0.050 SR0504-250R250C10 175 Ct10 200 250 ±0.14 ー 0.240 ∼0.050

Note）Please designate end-journal profile with your sketch. Note）Please designate end-journal profile with your sketch.

A249 A250
Ball Scresw

Ball Scresw
Standard products in stock SR series Standard products in stock SR series

SR0601 Shaft dia.φ6 Lead 1mm Ct7&Ct10 SR0601K Compact Nut

Shaft dia.φ6 Lead 1mm Ct7&Ct10
＊Please refer to page A281 for stainless steel type.

17
4-φ3.4 4-φ3.4 14.5
4 （13）
see below E-F see below E-F 3.5 （11）
30° 30°
30° 30°

−0.05
φ13 −0.10

−0.05
φ11 −0.10
E F E F

（φ5.85）

（φ5.9）
0
CD 2

φ26

φ23
P 17
PCD

C0
.5
C0
.5
Standard products in stock SR/SSR series

Standard products in stock SR/SSR series

15
16
（25） L1（Accuracy guaranteed area） （25）

L2 L1（Accuracy guaranteed area）

Unit：mm Unit：mm
Ball Screw Specifications Ball Screw Specifications

Ball size φ0.8 Ball size φ0.8

Number of thread 1 Number of thread 1

Thread direction Right Thread direction Right

Shaft root dia. φ5.3 Shaft root dia. φ5.3

Number of circuit 3.7×1 Number of circuit 1×3

Shaft S55C
Shaft, Nut material SCM415H material
Nut SCM415H

Surface hardness HRC58∼62 HRC58∼

Surface hardness
（Thread area） （Thread area）

Anti-rust treatment Anti-rust oil Anti-rust treatment Anti-rust oil

Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L1 L2
ep V300 Ca Coa ep V300 Ca Coa

SR0601-300R300C7 230 Ct7 250 300 ±0.04 ー 0.120 ∼0.020 SR0601K-200R200C7 175 Ct7 200 ー ±0.03 ー 0.080 ∼0.020
ー 680 1200 ー 560 950
SR0601-300R300C10 230 Ct10 250 300 ±0.17 ー 0.240 ∼0.050 SR0601K-200R200C10 175 Ct10 200 ー ±0.14 ー 0.160 ∼0.050

Note）Please designate end-journal profile with your sketch. Note）Please designate end-journal profile with your sketch.

A251 A252
Ball Scresw

Ball Scresw
Standard products in stock SR series Standard products in stock SR series

SR0602 Shaft dia.φ6 Lead 2mm Ct7&Ct10 SR0606 Shaft dia.φ6 Lead 6mm Ct7&Ct10

17
4−φ3.4 17 4-φ3.4
4 （8）
see below E-F see below E-F
4 （13）
30° 30° 30° 30°

0.05
−0.10
−0.05
φ15 −0.10

φ14 −
（φ5.8）
E F E F

（φ5.9）
22 21
PCD

φ27
PCD

φ28

C0
.5
19
Standard products in stock SR/SSR series

Standard products in stock SR/SSR series

16
（25） Ｌ1（Accuracy guaranteed area） （25） （25） Ｌ1（Accuracy guaranteed area） （25）

L2 L2

Unit：mm Unit：mm
Ball Screw Specifications Ball Screw Specifications

Ball size φ1.0 Ball size φ1.0

Number of thread 1 Number of thread 2

Thread direction Right Thread direction Right

Shaft root dia. φ5.1 Shaft root dia. φ5.2

Number of circuit 2.7×1 Number of circuit 1.6×2

Shaft, Nut material SCM415H Shaft, Nut material SCM415H

Surface hardness HRC58∼62 Surface hardness HRC58∼62

（Thread area） （Thread area）

Anti-rust treatment Anti-rust oil Anti-rust treatment Anti-rust oil

Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L1 L2
ep V300 Ca Coa ep V300 Ca Coa

SR0602-300R300C7 230 Ct7 250 300 ±0.04 ー 0.120 ∼0.020 SR0606-300R300C7 230 Ct7 250 300 ±0.04 ー 0.120 ∼0.020
ー 750 1200 ー 870 1450
SR0602-300R300C10 230 Ct10 250 300 ±0.17 ー 0.240 ∼0.050 SR0606-300R300C10 230 Ct10 250 300 ±0.17 ー 0.240 ∼0.050

Note）Please designate end-journal profile with your sketch. Note）Please designate end-journal profile with your sketch.

A253 A254
Ball Scresw

Ball Scresw
Standard products in stock SR series Standard products in stock SR series

SR0610 Shaft dia.φ6 Lead 10mm Ct7&Ct10 SR0801 Shaft dia.φ8 Lead 1mm Ct7&Ct10
＊Please refer to page A282 for stainless steel type.

23 17
4−φ3.4 4−φ3.4
4 （11.5） see below E-F 4 （13）
see below E-F
30° 30° 30° 30°

−0.05
φ14 −0.10

−0.05
φ16 −0.10
E F

（φ7.85）
E F

（φ5.9）
21 23

φ29
PCD

φ27
PCD

C0
.5
Standard products in stock SR/SSR series

Standard products in stock SR/SSR series

16 18
（25） Ｌ1（Accuracy guaranteed area） （25） （25） L1（Accuracy guaranteed area） （25）

L2 L2

Unit：mm Unit：mm
Ball Screw Specifications Ball Screw Specifications

Ball size φ1.2 Ball size φ0.8

Number of thread 2 Number of thread 1

Thread direction Right Thread direction Right

Shaft root dia. φ5.0 Shaft root dia. φ7.3

Number of circuit 1.2×2 Number of circuit 3.7×1

Shaft, Nut material SCM415H Shaft, Nut material SCM415H

Surface hardness HRC58∼62 Surface hardness HRC58∼62

（Thread area） （Thread area）

Anti-rust treatment Anti-rust oil Anti-rust treatment Anti-rust oil

Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L1 L2
ep V300 Ca Coa ep V300 Ca Coa

SR0610-300R300C7 225 Ct7 250 300 ±0.04 ー 0.120 ∼0.020 SR0801-400R400C7 330 Ct7 350 400 ±0.06 0.05 0.120 ∼0.020
ー 950 1600 ー 780 1650
SR0610-300R300C10 225 Ct10 250 300 ±0.17 ー 0.240 ∼0.050 SR0801-400R400C10 330 Ct10 350 400 ±0.24 0.21 0.240 ∼0.050

Note）Please designate end-journal profile with your sketch. Note）Please designate end-journal profile with your sketch.

A255 A256
Ball Scresw

Ball Scresw
Standard products in stock SR series Standard products in stock SR series

SR0801K Compact Nut

Shaft dia.φ8 Lead 1mm Ct7&Ct10 SR0802 Shaft dia.φ8 Lead 2mm Ct7&Ct10
＊Please refer to page A283 for stainless steel type.

4−φ4.5 24
15
4−φ3.4 5 （19）
30° 30°
4 （11） see below E-F
see below E-F
30° 30°

−0.05
φ20 −0.10
−0.05
φ13 −0.10
E F

（φ7.7）
E F

（φ7.9）
D 29

φ26
20

φ37
PC
PCD

C0
.5

C0
.5
Standard products in stock SR/SSR series

Standard products in stock SR/SSR series

17

22 （25） Ｌ1（Accuracy guaranteed area） （25）

L1（Accuracy guaranteed area）
L2

Unit：mm Unit：mm
Ball Screw Specifications Ball Screw Specifications

Ball size φ0.8 Ball size φ1.5875

Number of thread 1 Number of thread 1

Thread direction Right Thread direction Right

Shaft root dia. φ7.3 Shaft root dia. φ6.6

Number of circuit 1×3 Number of circuit 3.7×1

Shaft S55C
material Shaft, Nut material SCM415H
Nut SCM415H

Surface hardness HRC58∼ Surface hardness HRC58∼62

（Thread area） （Thread area）

Anti-rust treatment Anti-rust oil Anti-rust treatment Anti-rust oil

Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L1 L2
ep V300 Ca Coa ep V300 Ca Coa

SR0801K-230R230C7 200 Ct7 230 ー ±0.03 ー 0.080 ∼0.020 SR0802-400R400C7 325 Ct7 350 400 ±0.06 0.05 0.120 ∼0.020
ー 650 1300 ー 2400 4100
SR0801K-230R230C10 200 Ct10 230 ー ±0.16 ー 0.160 ∼0.050 SR0802-400R400C10 325 Ct10 350 400 ±0.24 0.21 0.240 ∼0.050

Note）Please designate end-journal profile with your sketch. Note）Please designate end-journal profile with your sketch.

A257 A258
Ball Scresw

Ball Scresw
Standard products in stock SR series Standard products in stock SR series

SR0802K Shaft dia.φ8 Lead 2mm

Compact Nut
Ct7&Ct10 SR0802.5 Shaft dia.φ8 Lead 2.5mm Ct7&Ct10

4−φ3.4
4−φ3.4 18
16
see below E-F 4 （14） 30° 30° see below E-F
4 （12）
30° 30°

−0.05
φ15 −0.10

−0.05
−0.10
E F E F

（φ7.9）

（φ7.4）

φ16
2 D 23

φ28
CD 2

φ29
P PC

C0

C0
.5

.5
Standard products in stock SR/SSR series

Standard products in stock SR/SSR series

18
19
（25） L1（Accuracy guaranteed area） （25）

Ｌ1（Accuracy guaranteed area） L2

Unit：mm Unit：mm
Ball Screw Specifications Ball Screw Specifications

Ball size φ1.2 Ball size φ1.5875

Number of thread 1 Number of thread 1

Thread direction Right Thread direction Right

Shaft root dia. φ7.0 Shaft root dia. φ6.3

Number of circuit 1×3 Number of circuit 2.7×1

Shaft S55C
Material Shaft, Nut material SCM415H
Nut SCM415H

Surface hardness HRC58∼ Surface hardness HRC58∼62

（Thread area） （Thread area）

Anti-rust treatment Anti-rust oil Anti-rust treatment Anti-rust oil

Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L1 L2
ep V300 Ca Coa ep V300 Ca Coa

SR0802K-230R230C7 200 Ct7 230 ー ±0.03 ー 0.080 ∼0.020 SR0802.5-400R400C7 330 Ct7 350 400 ±0.06 0.05 0.120 ∼0.020
ー 1300 2300 ー 1850 3000
SR0802K-230R230C10 200 Ct10 230 ー ±0.16 ー 0.160 ∼0.050 SR0802.5-400R400C10 330 Ct10 350 400 ±0.24 0.21 0.240 ∼0.050

Note）Please designate end-journal profile with your sketch. Note）Please designate end-journal profile with your sketch.

A259 A260
Ball Scresw

Ball Scresw
Standard products in stock SR series Standard products in stock SR series

SR0805 Shaft dia.φ8 Lead 5mm Ct7&Ct10 SR0808 Shaft dia.φ8 Lead 8mm Ct7&Ct10

4−φ3.4 28 4−φ3.4 20

see below E-F 4 （24） see below E-F 4 （10）

30° 30°
30° 30°

−0.05
−0.10

−0.05
φ18 −0.10
E F

（φ7.8）
E F

（φ7.9）
φ18
25
D 25

φ31
PCD

φ31
PC

C0
.5
Standard products in stock SR/SSR series

Standard products in stock SR/SSR series

20
20
（25） L1（Accuracy guaranteed area） （25） （25） L1（Accuracy guaranteed area） （25）

L2 L2

Unit：mm Unit：mm
Ball Screw Specifications Ball Screw Specifications

Ball size φ1.5875 Ball size φ1.5875

Number of thread 1 Number of thread 2

Thread direction Right Thread direction Right

Shaft root dia. φ6.6 Shaft root dia. φ6.7

Number of circuit 2.7×1 Number of circuit 1.6×2

Shaft, Nut material SCM415H Shaft, Nut material SCM415H

Surface hardness HRC58∼62 Surface hardness HRC58∼62

（Thread area） （Thread area）

Anti-rust treatment Anti-rust oil Anti-rust treatment Anti-rust oil

Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L1 L2
ep V300 Ca Coa ep V300 Ca Coa

SR0805-400R400C7 320 Ct7 350 400 ±0.06 0.05 0.120 ∼0.020 SR0808-400R400C7 330 Ct7 350 400 ±0.06 0.05 0.120 ∼0.020
ー 1850 3000 ー 2200 3800
SR0805-400R400C10 320 Ct10 350 400 ±0.24 0.21 0.240 ∼0.050 SR0808-400R400C10 330 Ct10 350 400 ±0.24 0.21 0.240 ∼0.050

Note）Please designate end-journal profile with your sketch. Note）Please designate end-journal profile with your sketch.

A261 A262
Ball Scresw

Ball Scresw
Standard products in stock SR series Standard products in stock SR series

SR0810 Shaft dia.φ8 Lead 10mm Ct7&Ct10 SR0812 Shaft dia.φ8 Lead 12mm Ct7&Ct10

4−φ3.4 24 4−φ3.4 27

4 （13） see below E-F 4 （17）

30° 30° see below E-F 30° 30°

−0.05
−0.10

−0.05
φ18 −0.10
（φ7.9）
E F E F

（φ7.9）

φ18
5
D 25

φ31
CD 2

φ31
PC P
Standard products in stock SR/SSR series

Standard products in stock SR/SSR series

20 20
（25） L1（Accuracy guaranteed area） （25） （25） L1（Accuracy guaranteed area） （25）

L2 L2

Unit：mm Unit：mm
Ball Screw Specifications Ball Screw Specifications

Ball size φ1.5875 Ball size φ1.5875

Number of thread 2 Number of thread 2

Thread direction Right Thread direction Right

Shaft root dia. φ6.7 Shaft root dia. φ6.7

Number of circuit 1.6×2 Number of circuit 1.6×2

Shaft, Nut material SCM415H Shaft, Nut material SCM415H

Surface hardness HRC58∼62 Surface hardness HRC58∼62

（Thread area） （Thread area）

Anti-rust treatment Anti-rust oil Anti-rust treatment Anti-rust oil

Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L1 L2
ep V300 Ca Coa ep V300 Ca Coa

SR0810-400R400C7 325 Ct7 350 400 ±0.06 0.05 0.120 ∼0.020 SR0812-400R400C7 320 Ct7 350 400 ±0.06 0.05 0.120 ∼0.020
ー 2200 3800 ー 2200 4000
SR0810-400R400C10 325 Ct10 350 400 ±0.24 0.21 0.240 ∼0.050 SR0812-400R400C10 320 Ct10 350 400 ±0.24 0.21 0.240 ∼0.050

Note）Please designate end-journal profile with your sketch. Note）Please designate end-journal profile with your sketch.

A263 A264
Ball Scresw

Ball Scresw
Standard products in stock SR series Standard products in stock SR series

SR1002 Shaft dia.φ10 Lead 2mm Ct7&Ct10 SR1002K Compact Nut

Shaft dia.φ10 Lead 2mm Ct7&Ct10
＊Please refer to page A284 for stainless steel type.

4−φ4.5 24
4−φ4.5 19
5 （19）
30° 30° 5 （14）
see below E-F 30° 30° see below E-F

−0.05
φ23 −0.10

−0.05
φ17 −0.10
（φ9.9）
E F

（φ9.7）
E F

φ34
32 26

φ40
PCD PCD

C0
.5
C0
Standard products in stock SR/SSR series

Standard products in stock SR/SSR series

.5
21
25 （25） L1（Accuracy guaranteed area） （25）

L2 L1（Accuracy guaranteed area）

Unit：mm Unit：mm
Ball Screw Specifications Ball Screw Specifications

Ball size φ1.5875 Ball size φ1.2

Number of thread 1 Number of thread 1

Thread direction Right Thread direction Right

Shaft root dia. φ8.6 Shaft root dia. φ9.0

Number of circuit 3.7×1 Number of circuit 1×3

Shaft S55C
Shaft, Nut material SCM415H Material
Nut SCM415H

Surface hardness HRC58∼62 Surface hardness HRC58∼

（Thread area） （Thread area）

Anti-rust treatment Anti-rust oil Anti-rust treatment Anti-rust oil

Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L1 L2
ep V300 Ca Coa ep V300 Ca Coa

SR1002-400R400C7 325 Ct7 350 400 ±0.05 0.05 0.080 ∼0.020 SR1002K-230R230C7 200 Ct7 230 ー ±0.03 ー 0.080 ∼0.020
ー 2700 5300 ー 1450 3000
SR1002-400R400C10 325 Ct10 350 400 ±0.24 0.21 0.160 ∼0.050 SR1002K-230R230C10 200 Ct10 230 ー ±0.16 ー 0.160 ∼0.050

Note）Please designate end-journal profile with your sketch. Note）Please designate end-journal profile with your sketch.

A265 A266
Ball Scresw

Ball Scresw
Standard products in stock SR series Standard products in stock SR series

SR1004 Shaft dia.φ10 Lead 4mm Ct7&Ct10 SR1005 Shaft dia.φ10 Lead 5mm Ct7&Ct10

28
4-φ4.5 4−φ4.5 26
5 （23）
5 （21）
30° 30° 30° 30°
see below E-F see below E-F

−0.05
φ23 −0.10
−0.05
−0.10
E F

（φ9.6）

（φ9.6）
φ24
E F
2

φ41
33 D3

φ40
PCD PC
Standard products in stock SR/SSR series

Standard products in stock SR/SSR series

C0
C1

.5
26 （25） L1（Accuracy guaranteed area） （25） 25 （25） L1（Accuracy guaranteed area） （25）

L2 L2

Unit：mm Unit：mm
Ball Screw Specifications Ball Screw Specifications

Ball size φ2.0 Ball size φ2.0

Number of thread 1 Number of thread 1

Thread direction Right Thread direction Right

Shaft root dia. φ8.2 Shaft root dia. φ8.2

Number of circuit 2.7×1 Number of circuit 2.7×1

Shaft, Nut material SCM415H Shaft, Nut material SCM415H

Surface hardness HRC58∼62 Surface hardness HRC58∼62

（Thread area） （Thread area）

Anti-rust treatment Anti-rust oil Anti-rust treatment Anti-rust oil

Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L1 L2
ep V300 Ca Coa ep V300 Ca Coa

SR1004-450R450C7 370 Ct7 400 450 ±0.06 0.05 0.120 ∼0.020 SR1005-450R450C7 370 Ct7 400 450 ±0.06 0.05 0.120 ∼0.020
ー 3000 5200 ー 3000 5200
SR1004-450R450C10 370 Ct10 400 450 ±0.28 0.21 0.240 ∼0.050 SR1005-450R450C10 370 Ct10 400 450 ±0.28 0.21 0.240 ∼0.050

Note）Please designate end-journal profile with your sketch. Note）Please designate end-journal profile with your sketch.

A267 A268
Ball Scresw

Ball Scresw
Standard products in stock SR series Standard products in stock SR series

SR1010 Shaft dia.φ10 Lead 10mm Ct7&Ct10 SR1015 Shaft dia.φ10 Lead 15mm Ct7&Ct10

4−φ4.5 24 4−φ4.5 33

5 （13）
30° 30°
30° 30° 5 （22）
see below E-F see below E-F

−0.05
φ23 −0.10

−0.05
φ23 −0.10
E F

（φ9.8）
（φ9.8）
E F
32

φ40
32

φ40
PCD PCD
Standard products in stock SR/SSR series

Standard products in stock SR/SSR series

25 （25） L1（Accuracy guaranteed area） （25） 25 （25） Ｌ1（Accuracy guaranteed area） （25）

L2 L2

Unit：mm Unit：mm
Ball Screw Specifications Ball Screw Specifications

Ball size φ2.0 Ball size φ2.0

Number of thread 2 Number of thread 2

Thread direction Right Thread direction Right

Shaft root dia. φ8.4 Shaft root dia. φ8.4

Number of circuit 1.6×2 Number of circuit 1.6×2

Shaft, Nut material SCM415H Shaft, Nut material SCM415H

Surface hardness HRC58∼62 Surface hardness HRC58∼62

（Thread area） （Thread area）

Anti-rust treatment Anti-rust oil Anti-rust treatment Anti-rust oil

Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L1 L2
ep V300 Ca Coa ep V300 Ca Coa

SR1010-450R450C7 375 Ct7 400 450 ±0.06 0.05 0.120 ∼0.020 SR1015-450R450C7 365 Ct7 400 450 ±0.06 0.05 0.120 ∼0.020
ー 3300 5900 ー 3300 6400
SR1010-450R450C10 375 Ct10 400 450 ±0.28 0.21 0.240 ∼0.050 SR1015-450R450C10 365 Ct10 400 450 ±0.28 0.21 0.240 ∼0.050

Note）Please designate end-journal profile with your sketch. Note）Please designate end-journal profile with your sketch.

A269 A270
Ball Scresw

Ball Scresw
Standard products in stock SR series Standard products in stock SR series

SR1020 Shaft dia.φ10 Lead 20mm Ct7&Ct10 SR1202 Shaft dia.φ12 Lead 2mm Ct7&Ct10

4−φ4.5 23 4-φ4.5 24

5 （13） see below E-F 5 （19）

30° 30°
30° 30°
see below E-F

−0.05
φ25 −0.10
−0.05
φ20 −0.10

（φ11.7）
E F

（φ9.9）
E F

φ42
29 34

φ37
PCD PCD

C0
.5
Standard products in stock SR/SSR series

Standard products in stock SR/SSR series

22 （25） Ｌ1（Accuracy guaranteed area） （25） 27 （25） L1（Accuracy guaranteed area） （25）

L2 L2

Unit：mm Unit：mm
Ball Screw Specifications Ball Screw Specifications

Ball size φ1.5875 Ball size φ1.5875

Number of thread 4 Number of thread 1

Thread direction Right Thread direction Right

Shaft root dia. φ8.7 Shaft root dia. φ10.6

Number of circuit 0.7×4 Number of circuit 3.7×1

Shaft, Nut material SCM415H Shaft, Nut material SCM415H

Surface hardness HRC58∼62 Surface hardness HRC58∼62

（Thread area） （Thread area）

Anti-rust treatment Anti-rust oil Anti-rust treatment Anti-rust oil

Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L1 L2
ep V300 Ca Coa ep V300 Ca Coa

SR1020-450R450C7 375 Ct7 400 450 ±0.06 0.05 0.120 ∼0.020 SR1202-450R450C7 375 Ct7 400 450 ±0.06 0.05 0.080 ∼0.020
ー 2100 4000 ー 3000 6400
SR1020-450R450C10 375 Ct10 400 450 ±0.28 0.21 0.240 ∼0.050 SR1202-450R450C10 375 Ct10 400 450 ±0.28 0.21 0.160 ∼0.050

Note）Please designate end-journal profile with your sketch. Note）Please designate end-journal profile with your sketch.

A271 A272
Ball Scresw

Ball Scresw
Standard products in stock SR series Standard products in stock SR series

SR1202K Compact Nut

Shaft dia.φ12 Lead 2mm Ct7&Ct10 SR1210 Shaft dia.φ12 Lead 10mm Ct7&Ct10

4-φ4.5
19 4−φ4.5 30
see below E-F
30° 30° see below E-F 5 （14）
30° 30° 6 （14.5）

−0.05
−0.10
−0.05
φ19 −0.10

（φ11.75）
E F

（φ11.9）
E F

φ24
φ36
33

φ41
28 PCD
PCD

C0
.5
Standard products in stock SR/SSR series

Standard products in stock SR/SSR series

26
23 （25） L1（Accuracy guaranteed area） （25）

L1（Accuracy guaranteed area） L2

Unit：mm Unit：mm
Ball Screw Specifications Ball Screw Specifications

Ball size φ1.2 Ball size φ2.381

Number of thread 1 Number of thread 2

Thread direction Right Thread direction Right

Shaft root dia. φ11.0 Shaft root dia. φ10.2

Number of circuit 1×3 Number of circuit 1.7×2

Shaft S55C
material Shaft, Nut material SCM415H
Nut SCM415H

Surface hardness HRC58∼ Surface hardness HRC58∼62

（Thread area） （Thread area）

Anti-rust treatment Anti-rust oil Anti-rust treatment Anti-rust oil

Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L1 L2
ep V300 Ca Coa ep V300 Ca Coa

SR1202K-280R280C7 250 Ct7 280 ー ±0.04 ー 0.080 ∼0.020 SR1210-450R450C7 370 Ct7 400 450 ±0.06 0.05 0.080 ∼0.020
ー 1600 3700 ー 5100 9800
SR1202K-280R280C10 250 Ct10 280 ー ±0.19 ー 0.160 ∼0.050 SR1210-450R450C10 370 Ct10 400 450 ±0.28 0.21 0.160 ∼0.050

Note）Please designate end-journal profile with your sketch. Note）Please designate end-journal profile with your sketch.

A273 A274
Ball Scresw

Ball Scresw
Standard products in stock SR series Standard products in stock SR series

SR1402 Shaft dia.φ14 Lead 2mm Ct7&Ct10 SR1404 Shaft dia.φ14 Lead 4mm Ct7&Ct10

25 4-φ5.5 33
4−φ5.5
6 （19） 6 （27）
see below E-F 30° 30° see below E-F
30° 30°

−0.05
φ26 −0.10

−0.05
φ30 −0.10
（φ13.7）

（φ13.5）
E F E F

φ49
0
D 36

φ45
PCD4
PC

C0

C1
.5
Standard products in stock SR/SSR series

Standard products in stock SR/SSR series

28
（25） L1（Accuracy guaranteed area） （25） 32 （25） L1（Accuracy guaranteed area） （25）

L2 L2

Unit：mm Unit：mm
Ball Screw Specifications Ball Screw Specifications

Ball size φ1.5875 Ball size φ2.381

Number of thread 1 Number of thread 1

Thread direction Right Thread direction Right

Shaft root dia. φ12.6 Shaft root dia. φ11.8

Number of circuit 3.7×1 Number of circuit 3.7×1

Shaft, Nut material SCM415H Shaft, Nut material SCM415H

Surface hardness HRC58∼62 Surface hardness HRC58∼62

（Thread area） （Thread area）

Anti-rust treatment Anti-rust oil Anti-rust treatment Anti-rust oil

Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L1 L2
ep V300 Ca Coa ep V300 Ca Coa

SR1402-500R500C7 425 Ct7 450 500 ±0.07 0.05 0.080 ∼0.020 SR1404-500R500C7 415 Ct7 450 500 ±0.07 0.05 0.080 ∼0.020
ー 3200 7500 ー 5700 11600
SR1402-500R500C10 425 Ct10 450 500 ±0.31 0.21 0.160 ∼0.050 SR1404-500R500C10 415 Ct10 450 500 ±0.31 0.21 0.160 ∼0.050

Note）Please designate end-journal profile with your sketch. Note）Please designate end-journal profile with your sketch.

A275 A276
Ball Scresw

Ball Scresw
Standard products in stock SR series Standard products in stock SR series

SR1505 Shaft dia.φ15 Lead 5mm Ct10 SR1510 Shaft dia.φ15 Lead 10mm Ct10

33 43
4−φ5.5 4−φ5.5
φ9.5 Depth 5.5 Facing 11 （16） φ9.5 Ｄｅｐｔｈ 5.5 Ｆａｃ
ｉｎｇ 11 （21）

30° 30° M6（Oil hole）

see below E-F
5.5 30° 30° M6（Oil hole）
see below E-F
5.5

−0.05
−0.10
−0.05
φ34 −0.10

φ34
E F E F

（φ15）
（φ15）

φ57

φ57
45 45
PCD PCD

50
50
Standard products in stock SR/SSR series

Standard products in stock SR/SSR series

34 34

L2 L2

Unit：mm Unit：mm
Ball Screw Specifications Ball Screw Specifications

Ball size φ3.175 Ball size φ3.175

Number of thread 1 Number of thread 2

Thread direction Right Thread direction Right

Shaft root dia. φ12.2 Shaft root dia. φ12.2

Number of circuit 3.7×1 Number of circuit 2.7×2

Shaft SUJ2 Shaft SUJ2

Material Material
Nut SCM415 Nut SCM415

Surface hardness HRC58∼62 Surface hardness HRC58∼62

（Thread area） （Thread area）

Anti-rust treatment Anti-rust oil Anti-rust treatment Anti-rust oil

Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L1 L2
ep V300 Ca Coa ep V300 Ca Coa

SR1505-1000R1000C10 965 Ct10 ― 1000 ±0.7 0.21 0.400 ∼0.050 ー 8900 17000 SR1510-1000R1000C10 955 Ct10 ― 1000 ±0.7 0.21 0.400 ∼0.050 ー 12000 25000

Note）Please designate end-journal profile with your sketch. Note）Please designate end-journal profile with your sketch.

A277 A278
Ball Scresw

Ball Scresw
Standard products in stock SR series

SR1520 Shaft dia.φ15 Lead 20mm Ct10

52
4−φ5.5
φ9.5 Depth 5.5 Facing 11 （28.5）

30° 30° M6（Oil hole）

see below E-F
5.5

−0.05
φ34 −0.10
E F

（φ15）

φ57
45
PCD
50
Standard products in stock SR/SSR series

Standard products in stock SR/SSR series

34

L2

Unit：mm
Ball Screw Specifications

Ball size φ3.175

Number of thread 2

Thread direction Right

Shaft root dia. φ12.7

Number of circuit 1.7×2

Shaft SUJ2
Material
Nut SCM415

Surface hardness HRC58∼62

（Thread area）

Anti-rust treatment Anti-rust oil

Unit：mm

Basic Load Rating

Shaft length Lead accuracy
N
Preload
Ball Screw Model Travel Grade Total Axial Torque
Run-out play
Travel deviation Variation Nm Dynamic Static
L1 L2
ep V300 Ca Coa

SR1520-1000R1000C10 945 Ct10 ― 1000 ±0.7 0.21 0.400 ∼0.050 ー 8000 16000

Note）Please designate end-journal profile with your sketch.

A279 A280
Ball Scresw

Ball Scresw
Standard products in stock SSR series Standard products in stock SSR series

SSR0601 Stainless
Shaft dia.φ6 Lead 1mm Ct7＆Ct10 SSR0801 Stainless
Shaft dia.φ8 Lead 1mm Ct7＆Ct10

17 4−φ3.4 17
4-φ3.4
4 （13） see below G 4 （13）
see below G 30° 30°

（φ7.85）
30° 30°

-0.05
φ16 -0.10
-0.05
φ13 -0.10
（φ5.85）
23

φ29

40°
PCD

φ4.5
φ26

40°
20
PCD

φ6
Ｇ

C0
Ｇ

.5
C0
.5
Standard products in stock SR/SSR series

Standard products in stock SR/SSR series

18
16
8 Ｌ1（Ｑｕｅｎｃｈｅｄａｒｅａ） 35 8 Ｌ1（Ｑｕｅｎｃｈｅｄａｒｅａ） 40

L2 L2

Unit：mm Unit：mm
Ball Screw Specifications Ball Screw Specifications

Ball size φ0.8 Ball size φ0.8

Number of thread 1 Number of thread 1

Thread direction Right Thread direction Right

Shaft root dia. φ5.3 Shaft root dia. φ7.3

Number of circuit 3.7×1 Number of circuit 3.7×1

Shaft,Nut material SUS440C Shaft,Nut material SUS440C

Surface hardness HRC55∼ Surface hardness HRC55∼

（Thread area） （Thread area）

Anti-rust treatment Anti-rust oil Anti-rust treatment Anti-rust oil

Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L1 L2
ep V300 Ca Coa ep V300 Ca Coa

SSR0601-300C7 240 Ct7 257 300 ±0.04 ー 0.120 ∼0.020 SSR0801-400C7 335 Ct7 352 400 ±0.06 0.05 0.120 ∼0.020
ー 560 900 ー 630 1250
SSR0601-300C10 240 Ct10 257 300 ±0.17 ー 0.240 ∼0.050 SSR0801-400C10 335 Ct10 352 400 ±0.24 0.21 0.240 ∼0.050

Note）Please designate end-journal profile with your sketch. Note）Please designate end-journal profile with your sketch.

A281 A282
Ball Scresw

Ball Scresw
Standard products in stock SSR series Standard products in stock SSR series

SSR0802 Stainless
Shaft dia.φ8 Lead 2mm Ct7＆Ct10 SSR1002 Stainless
Shaft dia.φ10 Lead 2mm Ct7＆Ct10

4-φ4.5 4−φ4.5
24 24
30° 30° 30°
5 （19） 30° 5 （19）
see below G see below G

-0.05
φ23 -0.10
-0.05
φ20 -0.10
（φ7.7）

（φ9.7）

φ40
φ37
29 32

40°
PCD PCD

40°

φ6

φ8
Ｇ Ｇ

C0
.5

C0
Standard products in stock SR/SSR series

Standard products in stock SR/SSR series

.5
22 25
8 Ｌ1（Ｑｕｅｎｃｈｅｄａｒｅａ） 40 8 Ｌ1 （Ｑｕｅｎｃｈｅｄａｒｅａ） 45
L2 L2

Unit：mm Unit：mm
Ball Screw Specifications Ball Screw Specifications

Ball size φ1.5875 Ball size φ1.5875

Number of thread 1 Number of thread 1

Thread direction Right Thread direction Right

Shaft root dia. φ6.6 Shaft root dia. φ8.6

Number of circuit 3.7×1 Number of circuit 3.7×1

Shaft,Nut material SUS440C Shaft,Nut material SUS440C

Surface hardness HRC55∼ Surface hardness HRC55∼

（Thread area） （Thread area）

Anti-rust treatment Anti-rust oil Anti-rust treatment Anti-rust oil

Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L1 L2
ep V300 Ca Coa ep V300 Ca Coa

SSR0802-400C7 325 Ct7 352 400 ±0.06 0.05 0.120 ∼0.020 SSR1002-400C7 320 Ct7 347 400 ±0.06 0.05 0.080 ∼0.020
ー 1950 3100 ー 2200 4000
SSR0802-400C10 325 Ct10 352 400 ±0.24 0.21 0.240 ∼0.050 SSR1002-400C10 320 Ct10 347 400 ±0.24 0.21 0.160 ∼0.050

Note）Please designate end-journal profile with your sketch. Note）Please designate end-journal profile with your sketch.

A283 A284
Ball Scresw

Ball Scresw
●Combination of Shaft nominal dia. & Lead Unit：mm

Lead

SRT/SSRT series
1 2 2.5 4 5 6 8 10 12 15 20
Shaft dia.

Standardized Rolled Ball Screws with Integrated end-journal 4

A289
A290
A291

5 A292
For production reason, Rolled Ball Screws are normally necessary to have smaller end-journal, but as KSS has
adopted special technology, it enables fixed end-journal bigger than Shaft diameter alike Ground Ball Screws. A293
This technology enables stable and more flexible on end-journal design. 6 A294 A295 A296 A297
A315
A298 A300
8 A299 A301 A302 A303 A304 A305
A316 A317
●Features A306
Design flexibility and wide use of Bearings on end-journal. 10 A307 A308 A309 A310 A311
A318
Compatible end-journal to Precision Ball Screws.
A312
No need to insert or press fit collar as Bearing shoulder. 12 A313
A314
Quick delivery due to unfinished end-journal stock.
Stainless Rolled Ball Screws are also available. Note 1）Yellow cells are available for Stainless Shaft and Nut.
Note 2）The numbers in a table：showing a page in this catalogue
Standard products in stock SRT/SSRT series

Standard products in stock SRT/SSRT series

●Accuracy Grade & Axial play
The grade of SRT/SSRT series（Standardized Rolled & Stainless Rolled Ball Screws with Integrated end-
Possible to have across flats Design flexibility & compatible design journal）are Ct7 and Ct10（JIS B 1192-3）.
Cost saving by Rolled process to Precision Ball Screws According to accuracy grade, Axial play 0.020mm or less（Ct7）and 0.050mm or less（Ct10）are in stock.

Not necessary to put or press fit a collar Flanged end-journal for Bearing face ●Material & Surface hardness
The material and hardness of SRT/SSRT series（Standardized Rolled & Stainless Rolled Ball Screws with
Integrated end-journal）are as follows.

Products Material of thread area Heat treatment Surface hardness

●Comparison with current model
***Shaft nominal diameter：φ10mm Shaft：
SCM415
Bearing face Rolled Ball Screws S55C Carburizing and Quenching
HRC58 or more
（SRT series ） Induction hardening
Nut：SCM415
φ11.5
φ10

φ10

φ8

φ6
φ8

φ6

Shaft：SUS440C Induction hardening

Stainless Rolled Ball Screws
HRC55 or more
（SSRT series ）
Nut：SUS440C Vacuum hardening

Across flats
Current model design New model design

A285 A286
Ball Scresw

Ball Scresw
●Lubrication
Fig. A-24：Shaft end-journal profile Fig. A-25：Nut Flange direction
SRT/SSRT series（Standardized Rolled & Stainless Rolled Ball Screws with Integrated end-journal）will be
supplied with anti-rust oil.
This oil is not lubricant, when Ball Screw operates, lubricant should be applied. X：Fixed side
If there is no specific instruction, KSS would recommend our original Grease（MSG No.2）as standard
A-type：Free
lubricant. Please feel free to contact us.

B-type：Journal with snap ring groove

●Precision Rolled Ball Screws Y：Supported side

High accuracy（JIS C5）can be produced by Rolled process, what we call Precision Rolled Ball Screws（PSR/
PSRT series）.Please see page A319.
C-type：Journal only

D-type：Other than the above

●Note
●Model number notation
1）The detail of end-journal dimension for each size is shown from next page.
2）KSS does not make additional Nut machining.
3）The specification is subject to change without notice.
Standard products in stock SRT/SSRT series

Standard products in stock SRT/SSRT series

4）If the other configuration except（A,B,C）is requested, please contact KSS.
SRT 04 01 K ー 086 R 126 C7 B 1 X
① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪

①Rolled Ball Screws Series No.

SRT ：Rolled Ball Screws with Integrated end-journal
SSRT ：Stainless Rolled Ball Screws with Integrated end-journal
②Screw Shaft nominal diameter （mm）
③Lead（mm）
④Ball Nut type
None：Standard
K：Compact type
⑤Screw thread length （mm）
（Specify in 1mm unit after end-journal machining）
⑥Thread direction （R=Right-hand）
⑦Screw Shaft total length（mm）
（Specify in 1mm units）
⑧Accuracy grade （C7 or C10）
⑨Shaft end-journal profile
Refer to Fig. A-24 below：A-type,B-type,C-type,
D-type（other）
⑩Anti-rust oil or Lubricant
0：KSS grease（MSG No.2）
1：Anti-rust oil（Non Ruster PZ2）
2：Multemp PS2 grease
3：Other
⑪Nut Flange direction（Refer to Fig. A-25 below）

A287 A288
 Ball Scresw

Ball Scresw
Standard products in stock SRT series Standard products in stock SRT series

SRT0401 Shaft dia. φ4 Lead 1mm Ct7＆Ct10 SRT0401K Compact Nut

Shaft dia. φ4 Lead 1mm Ct7＆Ct10
１−ＳＲＴ０４０１

17 13 4-φ2.9
4-φ3.4 see below
see below G （13） 4 G
（10） 3 30° 30°
30° 30°
−0.05
φ11 −0.10

−0.05
−0.10
（φ3.95）
（φ3.85）

φ8.2
φ8.2
17 14

.5
.5

φ9
PCD PCD

φ23

φ19

C0
C0

.5
.5

C0
G
C0

L1 4 15 L1 4 13

L2 55 L2 35
L3 L3
Standard products in stock SRT/SSRT series

Standard products in stock SRT/SSRT series

Unit
Ａ１１−ＳＲＴ０４、
０５ ｊ ：
ｏmm
ｕｒｎａ
ｌ Unit
Ａ１１−ＳＲＴ０４、
０５ ｊ ：
ｏmm
ｕｒｎａ
ｌ

Ball Screw Specifications End-journal profile Supported-side Fixed-side Ball Screw Specifications End-journal profile Supported-side Fixed-side

Ball size φ0.8 A-type B-type C-type 0 Ball size φ0.6 A-type B-type C-type 0
5−0.2 M4×0.5 5−0.2 M4×0.5

φ6h8 −0.018

φ6h8 −0.018
Number of thread 1 Number of thread 1

φ3h6 −0.006

φ3h6 −0.006
30°
×0.3 30°
×0.3
±0.03

±0.03
−0.001
φ4−0.006

−0.001
φ4−0.006
0

0
−0.002
φ3−0.010

−0.002
φ3−0.010
0

0
−0.002
φ3−0.010

−0.002
φ3−0.010
2.5 2.5
φ2.7

φ2.7
Thread direction Right Thread direction Right

Shaft root dia. φ3.3 Shaft root dia. φ3.4

R0.15max R0.15max R0.2max R0.15max R0.15max R0.2max
+0.1 +0.1
L4＝L5ー33 L4＝L5ー40 L4＝L5ー33 L4＝L5ー40
Number of circuit 3.7×1 0.5 0 7 6.5 Number of circuit 1×3 0.5 0 7 6.5

L5 4.35 ±0.05 L5 18 5 L5 4.35 ±0.05 L5 18 5

Shaft SCM415H＋SUS303 Shaft S55C＋SUS303
Material 7 L4＝L5ー40 L4 4 6 23 Material 7 L4＝L5ー40 L4 4 6 23
Nut SCM415H Nut SCM415H
L5 L5 L5 L5
Surface hardness HRC58∼ Surface hardness HRC58∼
（Thread area） L4：Thread length after end-journal machining. （Thread area） L4：Thread length after end-journal machining.
L5：Total length after end-journal machining. L5：Total length after end-journal machining.

Anti-rust treatment Anti-rust oil Supported-side ： MSU-4CS/4G Anti-rust treatment Anti-rust oil Supported-side ： MSU-4CS/4GS
Support-unit Recommendation Support-unit Recommendation
Fixed-side ： MSU-4C/4G Fixed-side ： MSU-4C/4G
D-type : Other than the above. D-type : Other than the above.
Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L3 L1 L2 L3
ep V300 Ca Coa ep V300 Ca Coa

SRT0401-96R155C7 75 Ct7 96 100 155 ±0.02 ー 0.080 SRT0401K-76R115C7 60 Ct7 76 80 115 ±0.02 ー 0.080 ∼0.020
∼0.020 ー 300 430
SRT0401-216R275C7 195 Ct7 216 220 275 ±0.03 ー 0.120 SRT0401K-76R115C10 60 Ct10 76 80 115 ±0.05 ー 0.160 ∼0.050
ー 560 790
SRT0401-96R155C10 75 Ct10 96 100 155 ±0.06 ー 0.160 Note ）Please refer to page A287 for order code of end-journal machining.
∼0.050
SRT0401-216R275C10 195 Ct10 216 220 275 ±0.15 ー 0.240

Note ）Please refer to page A287 for order code of end-journal machining.

A289 A290
 Ball Scresw

Ball Scresw
Standard products in stock SRT series Standard products in stock SRT series

SRT0402 Shaft dia. φ4 Lead 2mm Ct7＆Ct10 SRT0504 Shaft dia. φ5 Lead 4mm Ct7＆Ct10
Ａ１１−ＳＲＴ０４０２ Ａ１１−ＳＲＴ０５０４

19 22 4-φ3.4
see below
4-φ3.4
G （15） 4
see below G （18） 4
30° 30° 30° 30°
−0.05
φ11 −0.10

−0.05
φ12 −0.10
（φ3.85）

（φ4.85）
φ8.2

φ8.2
.5

.5
17 18
PCD

C0

C0
φ24
φ23
PCD
.5

.5
C0

C0
G G

L1 4 15 L1 4 16
L2 55 L2 55
L3 L3
Standard products in stock SRT/SSRT series

Standard products in stock SRT/SSRT series

Unit
Ａ１１−ＳＲＴ０４、
０５ ｊ ：
ｏmm
ｕｒｎａ
ｌ Unit
Ａ１１−ＳＲＴ０４、
０５ ｊ ：
ｏmm
ｕｒｎａ
ｌ

Ball Screw Specifications End-journal profile Supported-side Fixed-side Ball Screw Specifications End-journal profile Supported-side Fixed-side

Ball size φ0.8 A-type B-type C-type 0 Ball size φ0.8 A-type B-type C-type
5−0.2 0
M4×0.5 5−0.2 M4×0.5

φ6h8 −0.018
Number of thread 1 Number of thread 1

φ6h8 −0.018
φ3h6 −0.006
30°
×0.3
±0.03

φ3h6 −0.006
30°
×0.3

±0.03
−0.001
φ4−0.006
0

−0.001
φ4−0.006
−0.002
φ3−0.010

0
0
−0.002
φ3−0.010

2.5

−0.002
φ3−0.010

0
−0.002
φ3−0.010
2.5
φ2.7

Thread direction Right Thread direction Right

φ2.7
Shaft root dia. φ3.3 Shaft root dia. φ4.3
R0.15max R0.15max R0.2max R0.15max R0.15max R0.2max
+0.1
L4＝L5ー33 L4＝L5ー40 +0.1
Number of circuit 2.7×1 0.5 0 7 6.5 Number of circuit 2.7×1 L4＝L5ー33 0.5 0 7 L4＝L5ー40 6.5
L5 4.35 ±0.05 L5 18 5 L5 4.35 ±0.05 L5 18 5
Shaft SCM415H＋SUS303 Shaft SCM415H＋SUS303
Material 7 L4＝L5ー40 L4 4 6 23 Material L4＝L5ー40 L4 4 6
Nut SCM415H Nut SCM415H 7 23
L5 L5 L5 L5
Surface hardness HRC58∼ Surface hardness HRC58∼
（Thread area） L4：Thread length after end-journal machining. （Thread area） L4：Thread length after end-journal machining.
L5：Total length after end-journal machining. L5：Total length after end-journal machining.

Anti-rust treatment Anti-rust oil Supported-side ： MSU-4CS/4GS Anti-rust treatment Anti-rust oil Supported-side ： MSU-4CS/4GS
Support-unit Recommendation Support-unit Recommendation
Fixed-side ： MSU-4C/4G Fixed-side ： MSU-4C/4G
D-type : Other than the above. D-type : Other than the above.
Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L3 L1 L2 L3
ep V300 Ca Coa ep V300 Ca Coa

SRT0402-96R155C7 75 Ct7 96 100 155 ±0.02 ー 0.080 SRT0504-96R155C7 70 Ct7 96 100 155 ±0.02 ー 0.080
∼0.020 ∼0.020
SRT0402-216R275C7 195 Ct7 216 220 275 ±0.03 ー 0.120 SRT0504-216R275C7 190 Ct7 216 220 275 ±0.03 ー 0.120
ー 420 570 ー 470 720
SRT0402-96R155C10 75 Ct10 96 100 155 ±0.06 ー 0.160 SRT0504-96R155C10 70 Ct10 96 100 155 ±0.06 ー 0.160
∼0.050 ∼0.050
SRT0402-216R275C10 195 Ct10 216 220 275 ±0.15 ー 0.240 SRT0504-216R275C10 190 Ct10 216 220 275 ±0.15 ー 0.240

Note ）Please refer to page A287 for order code of end-journal machining. Note ）Please refer to page A287 for order code of end-journal machining.

A291 A292
 Ball Scresw

Ball Scresw
Standard products in stock SRT series Standard products in stock SRT series

SRT0601 Shaft dia. φ6 Lead 1mm Ct7＆Ct10 SRT0601K Shaft dia. φ6 Lead 1mm
Compact Nut
Ct7＆Ct10
＊Please refer to page A315 for stainless steel type.

−ＳＲＴ０６０１

17 14.5
4-φ3.4 4-φ3.4
（13） 4 （11） 3.5
see below G see below G
30° 30° 30° 30°
−0.05
φ13 −0.10

−0.05
φ11 −0.10
（φ5.85）

（φ5.9）

φ9.7
φ9.7

.5
.5
20

C0
17

φ26

C0

φ23
PCD PCD
.5

.5
G G
C0

C0
15
16
L1 4 L1 4

L2 70 L2 40

L3 L3
Standard products in stock SRT/SSRT series

Standard products in stock SRT/SSRT series

Ａ１１−ＳＲＴ０６Unit
ｊ
ｏｕｒ ：mm
ｎａ
ｌ Ａ１１−ＳＲＴ０６Unit
ｊ
ｏｕｒ ：mm
ｎａ
ｌ

Ball Screw Specifications End-journal profile Supported-side Fixed-side Ball Screw Specifications End-journal profile Supported-side Fixed-side

Ball size φ0.8 A-type B-type C-type Ball size φ0.8 A-type B-type C-type
0 0
7 −0.2 7 −0.2
M5×0.5 M5×0.5
Number of thread 1 Number of thread 1

φ8h8 −0.022

φ8h8 −0.022
30°
×0.5 30°
×0.5

φ4h6 −0.008

φ4h6 −0.008
±0.03

±0.03
−0.001
φ5−0.006

−0.001
φ5−0.006
0

0
−0.002
φ4−0.010

−0.002
φ4−0.010
−0.002
φ4−0.010

−0.002
φ4−0.010
3 3

0
Thread direction Right Thread direction Right
φ3.7

φ3.7
Shaft root dia. φ5.3 Shaft root dia. φ5.3
R0.2max R0.2max R0.2max R0.2max R0.2max R0.2max
Number of circuit 3.7×1 L4＝L5ー36 0.5
+0.1
0 8 L4＝L5ー44 6.5 Number of circuit 1×3 L4＝L5ー36 0.5
+0.1
0 8 L4＝L5ー44 6.5

Shaft SCM415H＋SUS303 L5 5.35 ±0.05 L5 19 6 Shaft S55C＋SUS303 L5 5.35 ±0.05 L5 19 6

Material Material
Nut SCM415H 8 L4＝L5ー44 L4 4 7 25 Nut SCM415H 8 L4＝L5ー44 L4 4 7 25
L5 L5 L5 L5
Surface hardness HRC58∼ Surface hardness HRC58∼
（Thread area） L4：Thread length after end-journal machining. （Thread area） L4：Thread length after end-journal machining.
L5：Total length after end-journal machining. L5：Total length after end-journal machining.

Anti-rust treatment Anti-rust oil Supported-side ： MSU-5CS/5GS Anti-rust treatment Anti-rust oil Supported-side ： MSU-5CS/5GS
Support-unit Recommendation Support-unit Recommendation
Fixed-side ： MSU-5C/5G Fixed-side ： MSU-5C/5G
D-type : Other than the above. D-type : Other than the above.
Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L3 L1 L2 L3
ep V300 Ca Coa ep V300 Ca Coa

SRT0601-146R220C7 125 Ct7 146 150 220 ±0.02 ー 0.080 SRT0601K-91R135C7 70 Ct7 91 95 135 ±0.02 ー 0.080 ∼0.020
∼0.020 ー 560 950
SRT0601-261R335C7 240 Ct7 261 265 335 ±0.04 ー 0.120 SRT0601K-91R135C10 70 Ct10 91 95 135 ±0.06 ー 0.160 ∼0.050
ー 680 1200
SRT0601-146R220C10 125 Ct10 146 150 220 ±0.10 ー 0.160 Note ）Please refer to page A287 for order code of end-journal machining.
∼0.050
SRT0601-261R335C10 240 Ct10 261 265 335 ±0.18 ー 0.240

Note ）Please refer to page A287 for order code of end-journal machining.

A293 A294
 Ball Scresw

Ball Scresw
Standard products in stock SRT series Standard products in stock SRT series

SRT0602 Shaft dia. φ6 Lead 2mm Ct7＆Ct10 SRT0606 Shaft dia. φ6 Lead 6mm Ct7＆Ct10
−ＳＲＴ０６０２ Ａ１１−ＳＲＴ０６０６

4-φ3.4 17
17 4-φ3.4
（8） 4
see below G （13） 4
30° 30° see below G
30° 30°

−0.05
φ14 −0.10
−0.05
φ15 −0.10

（φ5.9）
（φ5.8）

φ9.7

φ9.7
22

.5

.5
21

φ28
PCD

φ27
C0

C0
PCD
.5
C0

G G
19 16
L1 4 L1 4
L2 70 L2 70
L3 L3
Standard products in stock SRT/SSRT series

Standard products in stock SRT/SSRT series

Ａ１１−ＳＲＴ０６Unit
ｊ
ｏｕｒ ：mm
ｎａ
ｌ Ａ１１−ＳＲＴ０６Unit
ｊ
ｏｕｒ ：mm
ｎａ
ｌ

Ball Screw Specifications End-journal profile Supported-side Fixed-side Ball Screw Specifications End-journal profile Supported-side Fixed-side

Ball size φ1.0 A-type B-type C-type Ball size φ1.0 A-type B-type C-type
0 0
7 −0.2 7 −0.2
M5×0.5 M5×0.5
Number of thread 1 Number of thread 2

φ8h8 −0.022

φ8h8 −0.022
30°
×0.5 30°
×0.5

φ4h6 −0.008

φ4h6 −0.008
±0.03

±0.03
−0.001
φ5−0.006

−0.001
φ5−0.006
0

0
−0.002
φ4−0.010
−0.002
φ4−0.010

−0.002
φ4−0.010
−0.002
φ4−0.010
3 3

0
Thread direction Right Thread direction Right
φ3.7

φ3.7
Shaft root dia. φ5.1 Shaft root dia. φ5.2
R0.2max R0.2max R0.2max R0.2max R0.2max R0.2max
Number of circuit 2.7×1 L4＝L5ー36 0.5
+0.1
0 8 L4＝L5ー44 6.5 Number of circuit 1.6×2 L4＝L5ー36 0.5
+0.1
0 8 L4＝L5ー44 6.5

Shaft SCM415H＋SUS303 L5 5.35 ±0.05 L5 19 6 Shaft SCM415H＋SUS303 L5 5.35 ±0.05 L5 19 6

Material Material
Nut SCM415H 8 L4＝L5ー44 L4 4 7 25 Nut SCM415H 8 L4＝L5ー44 L4 4 7 25
L5 L5 L5 L5
Surface hardness HRC58∼ Surface hardness HRC58∼
（Thread area） L4：Thread length after end-journal machining. （Thread area） L4：Thread length after end-journal machining.
L5：Total length after end-journal machining. L5：Total length after end-journal machining.

Anti-rust treatment Anti-rust oil Supported-side ： MSU-5CS/5GS Anti-rust treatment Anti-rust oil Supported-side ： MSU-5CS/5GS
Support-unit Recommendation Support-unit Recommendation
Fixed-side ： MSU-5C/5G Fixed-side ： MSU-5C/5G
D-type : Other than the above. D-type : Other than the above.
Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L3 L1 L2 L3
ep V300 Ca Coa ep V300 Ca Coa

SRT0602-146R220C7 125 Ct7 146 150 220 ±0.02 ー 0.080 SRT0606-146R220C7 125 Ct7 146 150 220 ±0.02 ー 0.080
∼0.020 ∼0.020
SRT0602-261R335C7 240 Ct7 261 265 335 ±0.04 ー 0.120 SRT0606-261R335C7 240 Ct7 261 265 335 ±0.04 ー 0.120
ー 750 1200 ー 870 1450
SRT0602-146R220C10 125 Ct10 146 150 220 ±0.10 ー 0.160 SRT0606-146R220C10 125 Ct10 146 150 220 ±0.10 ー 0.160
∼0.050 ∼0.050
SRT0602-261R335C10 240 Ct10 261 265 335 ±0.18 ー 0.240 SRT0606-261R335C10 240 Ct10 261 265 335 ±0.18 ー 0.240

Note ）Please refer to page A287 for order code of end-journal machining. Note ）Please refer to page A287 for order code of end-journal machining.

A295 A296
 Ball Scresw

Ball Scresw
Standard products in stock SRT series Standard products in stock SRT series

SRT0610 Shaft dia. φ6 Lead 10mm Ct7＆Ct10 SRT0801 Shaft dia. φ8 Lead 1mm Ct7＆Ct10
＊Please refer to page A316 for stainless steel type.
−ＳＲＴ０６１０ Ａ１１−ＳＲＴ０８０１

17
23 4-φ3.4 4-φ3.4
（13） 4
see below G （11.5） 4 see below G
30° 30° 30° 30°

−0.05
φ16 −0.10
−0.05
φ14 −0.10

（φ7.85）

φ14.2
（φ5.9）

.5
φ9.7
23

C0
.5

φ29
21 PCD

φ27

C0
PCD

.5
G G

C0
16
L1 4 L1 4 18
L2 70 L2 70
L3 L3
Standard products in stock SRT/SSRT series

Standard products in stock SRT/SSRT series

Ａ１１−ＳＲＴ０６Unit
ｊ
ｏｕｒ ：mm
ｎａ
ｌ Ａ１１−ＳＲＴ０８Unit
ｊ
ｏｕｒ ：mm
ｎａ
ｌ

Ball Screw Specifications End-journal profile Supported-side Fixed-side Ball Screw Specifications End-journal profile Supported-side Fixed-side

Ball size φ1.2 A-type B-type C-type Ball size φ0.8 A-type B-type C-type
0
7 −0.2
8
0
−0.2 M6×0.75
M5×0.5
Number of thread 2 Number of thread 1

φ9.5h8 −0.022

φ4.5h6 −0.008
φ8h8 −0.022
30°
×0.5

φ4h6 −0.008
±0.03

−0.001
φ5−0.006

φ5.7 −0.06

0
30°
×0.5

-0.001
φ6 -0.006

0
0
−0.002
φ4−0.010
−0.002
φ4−0.010

0
Thread direction Right Thread direction Right 3
φ3.7

−0.002
φ6 −0.010

−0.002
φ6−0.010
Shaft root dia. φ5.0 Shaft root dia. φ7.3
R0.2max R0.2max R0.2max
R0.2max R0.2max R0.2max
Number of circuit 1.2×2 L4＝L5ー36 0.5
+0.1
0 8 L4＝L5ー44 6.5 Number of circuit 3.7×1 +0.1
L4＝L5ー41 0.8 0 9 L4＝L5ー50 7
Shaft SCM415H＋SUS303 L5 5.35 ±0.05 L5 19 6 Shaft SCM415H＋SUS303 L5 6.8
+0.1
0 L5 22.5 7.5
Material Material L4
Nut SCM415H 8 L4＝L5ー44 L4 4 7 25 Nut SCM415H 9 L4＝L5ー50 4 7 30

L5 L5 L5
L5
Surface hardness HRC58∼ Surface hardness HRC58∼
（Thread area） L4：Thread length after end-journal machining. （Thread area） L4：Thread length after end-journal machining.
L5：Total length after end-journal machining. L5：Total length after end-journal machining.

Anti-rust treatment Anti-rust oil Supported-side ： MSU-5CS/5GS Anti-rust treatment Anti-rust oil Supported-side ： MSU-6CS/6GS
Support-unit Recommendation Support-unit Recommendation
Fixed-side ： MSU-5C/5G Fixed-side ： MSU-6C/6G
D-type : Other than the above. D-type : Other than the above.
Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L3 L1 L2 L3
ep V300 Ca Coa ep V300 Ca Coa

SRT0610-146R220C7 120 Ct7 146 150 220 ±0.02 ー 0.080 SRT0801-196R270C7 175 Ct7 196 200 270 ±0.03 ー 0.080
∼0.020 ∼0.020
SRT0610-261R335C7 235 Ct7 261 265 335 ±0.04 ー 0.120 SRT0801-356R430C7 335 Ct7 356 360 430 ±0.06 0.05 0.120
ー 950 1600 ー 780 1650
SRT0610-146R220C10 120 Ct10 146 150 220 ±0.10 ー 0.160 SRT0801-196R270C10 175 Ct10 196 200 270 ±0.13 ー 0.160
∼0.050 ∼0.050
SRT0610-261R335C10 235 Ct10 261 265 335 ±0.18 ー 0.240 SRT0801-356R430C10 335 Ct10 356 360 430 ±0.24 0.21 0.240

Note ）Please refer to page A287 for order code of end-journal machining. Note ）Please refer to page A287 for order code of end-journal machining.

A297 A298
Ball Scresw

Ball Scresw
Standard products in stock SRT series Standard products in stock SRT series

SRT0801K Shaft dia. φ8 Lead 1mm

Compact Nut
Ct7＆Ct10 SRT0802 Shaft dia. φ8 Lead 2mm Ct7＆Ct10
＊Please refer to page A317 for stainless steel type.

Ａ１１−ＳＲＴ０８０２

24 4-φ4.5

15 （19） 5
4-φ3.4 30° 30°
（11） 4 see below G

−0.05
φ20 −0.10
see below G
−0.05
φ13 −0.10 30° 30°

φ14.2
（φ7.7）
（φ7.9）

.5
φ11.7

φ37
29

C0
.5
20 PCD

C0
φ26
PCD
.5

.5
C0

C0
L1 4 17

L2 45 L1 4 22

L3 L2 70
L3
Standard products in stock SRT/SSRT series

Standard products in stock SRT/SSRT series

Ａ１１−ＳＲＴ０８Unit
ｊ
ｏｕｒ ：mm
ｎａ
ｌ Unit：mm
Ａ１１−ＳＲＴ０８ ｊ
ｏｕｒｎａ
ｌ
Ball Screw Specifications End-journal profile Supported-side Fixed-side Ball Screw Specifications End-journal profile Supported-side Fixed-side

Ball size φ0.8 A-type B-type C-type Ball size φ1.5875 A-type B-type C-type
0 0
8 −0.2 M6×0.75 8 −0.2 M6×0.75
Number of thread 1 Number of thread 1

φ9.5h8 −0.022

φ9.5h8 −0.022
φ4.5h6 −0.008

φ4.5h6 −0.008
φ5.7 −0.06

0
30°
×0.5

φ5.7 −0.06

0
30°
×0.5

-0.001
φ6 -0.006

-0.001
φ6 -0.006

0
0

0
Thread direction Right 3 Thread direction Right 3
−0.002
φ6 −0.010

−0.002
φ6−0.010

−0.002
φ6 −0.010

−0.002
φ6−0.010
Shaft root dia. φ7.3 Shaft root dia. φ6.6

R0.2max R0.2max R0.2max R0.2max R0.2max R0.2max

Number of circuit 1×3 +0.1 Number of circuit 3.7×1
L4＝L5ー41 0.8 0 9 L4＝L5ー50 7 L4＝L5ー41 0.8
+0.1
0 9 L4＝L5ー50 7
Shaft S55C＋SUS303 L5 6.8
+0.1
0 L5 22.5 7.5 Shaft SCM415H＋SUS303 L5 6.8
+0.1
0 L5 22.5 7.5
Material L4
Material
Nut SCM415H 9 L4＝L5ー50 4 7 30 Nut SCM415H 9 L4＝L5ー50 L4 4 7 30
L5 L5 L5
L5
Surface hardness HRC58∼ HRC58∼
L4：Thread length after end-journal machining. Surface hardness L4：Thread length after end-journal machining.
（Thread area） （Thread area）
L5：Total length after end-journal machining. L5：Total length after end-journal machining.

Anti-rust treatment Anti-rust oil Supported-side ： MSU-6CS/6GS Anti-rust treatment Anti-rust oil Supported-side ： MSU-6CS/6GS
Support-unit Recommendation Support-unit Recommendation
Fixed-side ： MSU-6C/6G Fixed-side ： MSU-6C/6G
D-type : Other than the above. D-type : Other than the above.
Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L3 L1 L2 L3
ep V300 Ca Coa ep V300 Ca Coa

SRT0801K-171R220C7 150 Ct7 171 175 220 ±0.03 ー 0.080 ∼0.020 SRT0802-196R270C7 170 Ct7 196 200 270 ±0.03 ー 0.080
ー 650 1300 ∼0.020
SRT0801K-171R220C10 150 Ct10 171 175 220 ±0.11 ー 0.160 ∼0.050 SRT0802-356R430C7 330 Ct7 356 360 430 ±0.06 0.05 0.120
ー 2400 4100
Note ）Please refer to page A287 for order code of end-journal machining. SRT0802-196R270C10 170 Ct10 196 200 270 ±0.13 ー 0.160
∼0.050
SRT0802-356R430C10 330 Ct10 356 360 430 ±0.24 0.21 0.240

Note ）Please refer to page A287 for order code of end-journal machining.

A299 A300
Ball Scresw

Ball Scresw
Standard products in stock SRT series Standard products in stock SRT series

SRT0802K Shaft dia. φ8 Lead 2mm

Compact Nut
Ct7＆Ct10 SRT0802.5 Shaft dia. φ8 Lead 2.5mm Ct7＆Ct10
Ａ１１−ＳＲＴ０８０２．
５

18 4-φ3.4 4-φ3.4
16
（14） 4
see below G （12） 4
30° 30° see below G 30° 30°
−0.05
φ15 −0.10

−0.05
φ16 −0.10
（φ7.9）

φ11.7

φ14.2
（φ7.4）
.5

.5
φ28
22

C0
PCD

C0
23

φ29
PCD
.5
C0

.5
G

C0
19 L1 4 18
L1 4
L2 70
L2 45
L3
L3
Standard products in stock SRT/SSRT series

Standard products in stock SRT/SSRT series

Ａ１１−ＳＲＴ０８ ｊ
ｏｕｒｎａ
ｌ
Unit：mm Ａ１１−ＳＲＴ０８ ｊ
ｏｕｒｎａ
ｌ
Unit：mm
Ball Screw Specifications End-journal profile Supported-side Fixed-side Ball Screw Specifications End-journal profile Supported-side Fixed-side

Ball size φ1.2 A-type B-type C-type Ball size φ1.5875 A-type B-type C-type
0 0
8 −0.2 M6×0.75 8 −0.2 M6×0.75
Number of thread 1 Number of thread 1

φ9.5h8 −0.022

φ9.5h8 −0.022
φ4.5h6 −0.008

φ4.5h6 −0.008
φ5.7 −0.06

φ5.7 −0.06
0

0
30°
×0.5 30°
×0.5

-0.001
φ6 -0.006

-0.001
φ6 -0.006
0

0
0

0
Thread direction Right 3 Thread direction Right 3
−0.002
φ6 −0.010

−0.002
φ6 −0.010
−0.002
φ6−0.010

−0.002
φ6−0.010
Shaft root dia. φ7.0 Shaft root dia. φ6.3

R0.2max R0.2max R0.2max R0.2max R0.2max R0.2max

Number of circuit 1×3 +0.1
Number of circuit 2.7×1 +0.1
L4＝L5ー41 0.8 0 9 L4＝L5ー50 7 L4＝L5ー41 0.8 0 9 L4＝L5ー50 7
Shaft S55C＋SUS303 L5 6.8
+0.1
0 L5 22.5 7.5 Shaft SCM415H＋SUS303 L5 6.8
+0.1
0 L5 22.5 7.5
Material Material
Nut SCM415H 9 L4＝L5ー50 L4 4 7 30 Nut SCM415H 9 L4＝L5ー50 L4 4 7 30

L5 L5 L5 L5
Surface hardness HRC58∼ HRC58∼
L4：Thread length after end-journal machining. Surface hardness L4：Thread length after end-journal machining.
（Thread area） （Thread area）
L5：Total length after end-journal machining. L5：Total length after end-journal machining.

Anti-rust treatment Anti-rust oil Supported-side ： MSU-6CS/6GS Anti-rust treatment Anti-rust oil Supported-side ： MSU-6CS/6GS
Support-unit Recommendation Support-unit Recommendation
Fixed-side ： MSU-6C/6G Fixed-side ： MSU-6C/6G
D-type : Other than the above. D-type : Other than the above.
Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L3 L1 L2 L3
ep V300 Ca Coa ep V300 Ca Coa

SRT0802K-171R220C7 145 Ct7 171 175 220 ±0.03 ー 0.080 ∼0.020 SRT0802.5-196R270C7 180 Ct7 196 200 270 ±0.03 ー 0.080
ー 1300 2300 ∼0.020
SRT0802K-171R220C10 145 Ct10 171 175 220 ±0.11 ー 0.160 ∼0.050 SRT0802.5-356R430C7 340 Ct7 356 360 430 ±0.06 0.05 0.120
ー 1850 3000
Note ）Please refer to page A287 for order code of end-journal machining. SRT0802.5-196R270C10 180 Ct10 196 200 270 ±0.13 ー 0.160
∼0.050
SRT0802.5-356R430C10 340 Ct10 356 360 430 ±0.24 0.21 0.240

Note ）Please refer to page A287 for order code of end-journal machining.

A301 A302
 Ball Scresw

Ball Scresw
Standard products in stock SRT series Standard products in stock SRT series

SRT0805 Shaft dia. φ8 Lead 5mm Ct7＆Ct10 SRT0808 Shaft dia. φ8 Lead 8mm Ct7＆Ct10
１−ＳＲＴ０８０５ Ａ１１−ＳＲＴ０８０８

28 4-φ3.4 20 4-φ3.4

（24） 4 （10） 4
see below G 30° 30° see below G 30° 30°
−0.05
φ18 −0.10

−0.05
φ18 −0.10
φ14.2

φ14.2
（φ7.8）

（φ7.9）
.5

.5
25

φ31

φ31
25

C0

C0
PCD PCD
.5

G G
C0

L1 4 20 L1 4 20
L2 70 L2 70
L3 L3
Standard products in stock SRT/SSRT series

Standard products in stock SRT/SSRT series

Ａ１１−ＳＲＴ０８ ｊ
ｏｕｒｎａ
ｌ
Unit：mm Ａ１１−ＳＲＴ０８Unit
ｊ
ｏｕｒ ：mm
ｎａ
ｌ
Ball Screw Specifications End-journal profile Supported-side Fixed-side Ball Screw Specifications End-journal profile Supported-side Fixed-side

Ball size φ1.5875 A-type B-type C-type Ball size φ1.5875 A-type B-type C-type
0 0
8 −0.2 M6×0.75 8 −0.2 M6×0.75
Number of thread 1 Number of thread 2

φ9.5h8 −0.022
φ9.5h8 −0.022

φ4.5h6 −0.008
φ4.5h6 −0.008

φ5.7 −0.06

0
30°
×0.5
φ5.7 −0.06

0
30°
×0.5

-0.001
φ6 -0.006

0
-0.001
φ6 -0.006

0
0

Thread direction Right 3 Thread direction Right 3

−0.002
φ6 −0.010

−0.002
φ6−0.010
−0.002
φ6 −0.010

−0.002
φ6−0.010

Shaft root dia. φ6.6 Shaft root dia. φ6.7

R0.2max R0.2max R0.2max R0.2max R0.2max R0.2max

Number of circuit 2.7×1 Number of circuit 1.6×2 +0.1
L4＝L5ー41 0.8
+0.1
0 9 L4＝L5ー50 7 L4＝L5ー41 0.8 0 9 L4＝L5ー50 7
Shaft SCM415H＋SUS303 L5 6.8
+0.1
0 L5 22.5 7.5 Shaft SCM415H＋SUS303 L5 6.8
+0.1
0 L5 22.5 7.5
Material Material
Nut SCM415H L4 4 7 30 Nut SCM415H 9 L4＝L5ー50 L4 4 7 30
9 L4＝L5ー50
L5 L5 L5
L5
Surface hardness HRC58∼ Surface hardness HRC58∼
（Thread area） L4：Thread length after end-journal machining. （Thread area） L4：Thread length after end-journal machining.
L5：Total length after end-journal machining. L5：Total length after end-journal machining.

Anti-rust treatment Anti-rust oil Supported-side ： MSU-6CS/6GS Anti-rust treatment Anti-rust oil Supported-side ： MSU-6CS/6GS
Support-unit Recommendation Support-unit Recommendation
Fixed-side ： MSU-6C/6G Fixed-side ： MSU-6C/6G
D-type : Other than the above. D-type : Other than the above.
Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L3 L1 L2 L3
ep V300 Ca Coa ep V300 Ca Coa

SRT0805-196R270C7 165 Ct7 196 200 270 ±0.03 ー 0.080 SRT0808-196R270C7 175 Ct7 196 200 270 ±0.03 ー 0.080
∼0.020 ∼0.020
SRT0805-356R430C7 325 Ct7 356 360 430 ±0.06 0.05 0.120 SRT0808-356R430C7 335 Ct7 356 360 430 ±0.06 0.05 0.120
ー 1850 3000 ー 2200 3800
SRT0805-196R270C10 165 Ct10 196 200 270 ±0.13 ー 0.160 SRT0808-196R270C10 175 Ct10 196 200 270 ±0.13 ー 0.160
∼0.050 ∼0.050
SRT0805-356R430C10 325 Ct10 356 360 430 ±0.24 0.21 0.240 SRT0808-356R430C10 335 Ct10 356 360 430 ±0.24 0.21 0.240

Note ）Please refer to page A287 for order code of end-journal machining. Note ）Please refer to page A287 for order code of end-journal machining.

A303 A304
 Ball Scresw

Ball Scresw
Standard products in stock SRT series Standard products in stock SRT series

SRT0812 Shaft dia. φ8 Lead 12mm Ct7＆Ct10 SRT1002 Shaft dia. φ10 Lead 2mm Ct7＆Ct10
＊Please refer to page A318 for stainless steel type.

−ＳＲＴ０８１２ Ａ１１−ＳＲＴ１００２

24 4-φ4.5
27 4-φ3.4
（19） 5 30° 30°
（17） 4 30°

−0.05
φ23 −0.10
see below G 30° see below G
−0.05
φ18 −0.10

（φ9.7）
φ14.2

φ14.2
（φ7.9）

.5

.5
32

φ40
25 PCD

C0
φ31

C0
PCD

G G

.5
C0
L1 4 20
L2 70 L1 4 25
L3 L2 70
L3
Standard products in stock SRT/SSRT series

Standard products in stock SRT/SSRT series

Ａ１１−ＳＲＴ０８Unit
ｊ
ｏｕｒ ：mm
ｎａ
ｌ Ａ１１−ＳＲＴ１０Unit
ｊ
ｏｕｒ ：mm
ｎａ
ｌ

Ball Screw Specifications End-journal profile Supported-side Fixed-side Ball Screw Specifications End-journal profile Supported-side Fixed-side

Ball size φ1.5875 A-type B-type C-type Ball size φ1.5875 A-type B-type C-type
0 0
8 −0.2 M6×0.75 10

φ11.5h8 −0.027
−0.2
Number of thread 2 Number of thread 1

φ9.5h8 −0.022
M8×1.0

φ4.5h6 −0.008

0
φ5.7 −0.06

φ6h6 −0.008
0
30°
×0.5 30°
×0.5

φ5.7 −0.06

−0.002
φ8−0.008
-0.001
φ6 -0.006

0
0

0
4

0
Thread direction Right 3 Thread direction Right
−0.002
φ6 −0.010

−0.002
φ6−0.010

−0.002
φ6 −0.010

−0.002
φ6−0.010
Shaft root dia. φ6.7 Shaft root dia. φ8.6

R0.2max R0.2max R0.2max R0.2max R0.2max R0.2max

Number of circuit 1.6×2 Number of circuit 3.7×1 L4＝L5ー49
+0.1
L4＝L5ー58
L4＝L5ー41 0.8
+0.1
0 9 L4＝L5ー50 7 0.8 0 9 9
Shaft SCM415H＋SUS303 L5 6.8
+0.1
0 L5 22.5 7.5 Shaft SCM415H＋SUS303 L5 6.8
+0.1
0 L5 27 10
Material Material
Nut SCM415H 9 L4＝L5ー50 L4 4 7 30 Nut SCM415H 9 L4＝L5ー58 L4 4 8 37
L5 L5 L5 L5
Surface hardness HRC58∼ Surface hardness HRC58∼
（Thread area） L4：Thread length after end-journal machining. （Thread area） L4：Thread length after end-journal machining.
L5：Total length after end-journal machining. L5：Total length after end-journal machining.

Anti-rust treatment Anti-rust oil Supported-side ： MSU-6CS/6GS Anti-rust treatment Anti-rust oil Supported-side ： MSU-8CS/8GS
Support-unit Recommendation Support-unit Recommendation
Fixed-side ： MSU-6C/6G Fixed-side ： MSU-8C/8G
D-type : Other than the above. D-type : Other than the above.
Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L3 L1 L2 L3
ep V300 Ca Coa ep V300 Ca Coa

SRT0812-196R270C7 165 Ct7 196 200 270 ±0.03 ー 0.080 SRT1002-196R270C7 170 Ct7 196 200 270 ±0.03 ー 0.080
∼0.020 ∼0.020
SRT0812-356R430C7 325 Ct7 356 360 430 ±0.06 0.05 0.120 SRT1002-396R470C7 370 Ct7 396 400 470 ±0.06 0.05 0.120
ー 2200 4000 ー 2700 5300
SRT0812-196R270C10 165 Ct10 196 200 270 ±0.13 ー 0.160 SRT1002-196R270C10 170 Ct10 196 200 270 ±0.13 ー 0.160
∼0.050 ∼0.050
SRT0812-356R430C10 325 Ct10 356 360 430 ±0.24 0.21 0.240 SRT1002-396R470C10 370 Ct10 396 400 470 ±0.27 0.21 0.240

Note ）Please refer to page A287 for order code of end-journal machining. Note ）Please refer to page A287 for order code of end-journal machining.

A305 A306
Ball Scresw

Ball Scresw
Standard products in stock SRT series Standard products in stock SRT series

SRT1002K Compact Nut

Shaft dia. φ10 Lead 2mm Ct7＆Ct10 SRT1005 Shaft dia. φ10 Lead 5mm Ct7＆Ct10
A11-SRT1005

26 4-φ4.5
19 4-φ4.5
（21） 5 30° 30°
（14） 5
30° 30°

−0.05
φ23 −0.10
see below G see below G
−0.05
φ17 −0.10

（φ9.6）
（φ9.9）

φ14.2
φ11.7

φ40

.5
32

.5
φ34
26 PCD

C0
C0
PCD
.5

G G
C0

.5
C0
L1 4 21
L1 4 25
L2 55 L2 70
L3 L3
Standard products in stock SRT/SSRT series

Standard products in stock SRT/SSRT series

Ａ１１−ＳＲＴ１０Unit
ｊ
ｏｕｒ ：mm
ｎａ
ｌ Ａ１１−ＳＲＴ１０Unit
ｊ
ｏｕｒ ：mm
ｎａ
ｌ

Ball Screw Specifications End-journal profile Supported-side Fixed-side Ball Screw Specifications End-journal profile Supported-side Fixed-side

Ball size φ1.2 A-type B-type C-type Ball size φ2.0 A-type B-type C-type
0 0
10 10

φ11.5h8 −0.027

φ11.5h8 −0.027
−0.2 −0.2
Number of thread 1 M8×1.0 Number of thread 1 M8×1.0

0
φ6h6 −0.008

φ6h6 −0.008
30°
×0.5 30°
×0.5
φ5.7 −0.06

φ5.7 −0.06
−0.002
φ8−0.008

−0.002
φ8−0.008
0

0
4 4

0
Thread direction Right Thread direction Right
−0.002
φ6 −0.010

−0.002
φ6 −0.010
−0.002
φ6−0.010

−0.002
φ6−0.010
Shaft root dia. φ9.0 Shaft root dia. φ8.2

R0.2max R0.2max R0.2max R0.2max R0.2max R0.2max

Number of circuit 1×3 L4＝L5ー49
+0.1
L4＝L5ー58
Number of circuit 2.7×1 L4＝L5ー49
+0.1
L4＝L5ー58
0.8 0 9 9 0.8 0 9 9
Shaft S55C＋SUS303 L5 6.8
+0.1
0 L5 27 10 Shaft SCM415H＋SUS303 L5 6.8
+0.1
0 L5 27 10
Material Material
Nut SCM415H 9 L4＝L5ー58 L4 4 8 37 Nut SCM415H 9 L4＝L5ー58 L4 4 8 37
L5 L5 L5 L5
Surface hardness HRC58∼ HRC58∼
L4：Thread length after end-journal machining. Surface hardness L4：Thread length after end-journal machining.
（Thread area） （Thread area）
L5：Total length after end-journal machining. L5：Total length after end-journal machining.

Anti-rust treatment Anti-rust oil Supported-side ： MSU-8CS/8GS Anti-rust treatment Anti-rust oil Supported-side ： MSU-8CS/8GS
Support-unit Recommendation Support-unit Recommendation
Fixed-side ： MSU-8C/8G Fixed-side ： MSU-8C/8G
D-type : Other than the above. D-type : Other than the above.
Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L3 L1 L2 L3
ep V300 Ca Coa ep V300 Ca Coa

SRT1002K-201R260C7 175 Ct7 201 205 260 ±0.03 ー 0.080 ∼0.020 SRT1005-196R270C7 170 Ct7 196 200 270 ±0.03 ー 0.080
ー 1450 3000 ∼0.020
SRT1002K-201R260C10 175 Ct10 201 205 260 ±0.14 ー 0.160 ∼0.050 SRT1005-396R470C7 370 Ct7 396 400 470 ±0.06 0.05 0.120
ー 3000 5200
Note ）Please refer to page A287 for order code of end-journal machining. SRT1005-196R270C10 170 Ct10 196 200 270 ±0.13 ー 0.160
∼0.050
SRT1005-396R470C10 370 Ct10 396 400 470 ±0.27 0.21 0.240

Note ）Please refer to page A287 for order code of end-journal machining.

A307 A308
 Ball Scresw

Ball Scresw
Standard products in stock SRT series Standard products in stock SRT series

SRT1010 Shaft dia. φ10 Lead 10mm Ct7＆Ct10 SRT1015 Shaft dia. φ10 Lead 15mm Ct7＆Ct10
−ＳＲＴ１０１０ Ａ１１−ＳＲＴ１０１５

24 4-φ4.5 33 4-φ4.5

（13） 5 30° 30° （22） 5 30° 30°

−0.05
φ23 −0.10

−0.05
φ23 −0.10
see below G see below G
（φ9.8）

φ14.2

（φ9.8）

φ14.2
.5
φ40
32

.5
φ40
32
PCD

C0

C0
PCD

G G

L1 4 25 L1 4 25
L2 70 L2 70
L3 L3
Standard products in stock SRT/SSRT series

Standard products in stock SRT/SSRT series

Ａ１１−ＳＲＴ１０Unit
ｊ
ｏｕｒ ：mm
ｎａ
ｌ Ａ１１−ＳＲＴ１０Unit
ｊ
ｏｕｒ ：mm
ｎａ
ｌ

Ball Screw Specifications End-journal profile Supported-side Fixed-side Ball Screw Specifications End-journal profile Supported-side Fixed-side

Ball size φ2.0 A-type B-type C-type Ball size φ2.0 A-type B-type C-type
0 0
10 10

φ11.5h8 −0.027
−0.2

φ11.5h8 −0.027
−0.2
Number of thread 2 M8×1.0 Number of thread 2 M8×1.0

0
0

φ6h6 −0.008
φ6h6 −0.008
30°
×0.5 30°
×0.5

φ5.7 −0.06
φ5.7 −0.06

−0.002
φ8−0.008
−0.002
φ8−0.008

0
0

0
4

0
Thread direction Right Thread direction Right

−0.002
φ6 −0.010
−0.002
φ6 −0.010

−0.002
φ6−0.010
−0.002
φ6−0.010

Shaft root dia. φ8.4 Shaft root dia. φ8.4

R0.2max R0.2max R0.2max R0.2max R0.2max R0.2max

Number of circuit 1.6×2 L4＝L5ー49
+0.1
L4＝L5ー58
Number of circuit 1.6×2 L4＝L5ー49 0.8
+0.1
9 L4＝L5ー58
0.8 0 9 9 0 9
Shaft SCM415H＋SUS303 L5 6.8
+0.1
0 L5 27 10 Shaft SCM415H＋SUS303 L5 6.8
+0.1
0 L5 27 10
Material Material
Nut SCM415H 9 L4＝L5ー58 L4 4 8 37 Nut SCM415H 9 L4＝L5ー58 L4 4 8 37
L5 L5 L5 L5
Surface hardness HRC58∼ Surface hardness HRC58∼
（Thread area） L4：Thread length after end-journal machining. （Thread area） L4：Thread length after end-journal machining.
L5：Total length after end-journal machining. L5：Total length after end-journal machining.

Anti-rust treatment Anti-rust oil Supported-side ： MSU-8CS/8GS Anti-rust treatment Anti-rust oil Supported-side ： MSU-8CS/8GS
Support-unit Recommendation Support-unit Recommendation
Fixed-side ： MSU-8C/8G Fixed-side ： MSU-8C/8G
D-type : Other than the above. D-type : Other than the above.
Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L3 L1 L2 L3
ep V300 Ca Coa ep V300 Ca Coa

SRT1010-196R270C7 170 Ct7 196 200 270 ±0.03 ー 0.080 SRT1015-196R270C7 160 Ct7 196 200 270 ±0.03 ー 0.080
∼0.020 ∼0.020
SRT1010-396R470C7 370 Ct7 396 400 470 ±0.06 0.05 0.120 SRT1015-396R470C7 360 Ct7 396 400 470 ±0.06 0.05 0.120
ー 3300 5900 ー 3300 6400
SRT1010-196R270C10 170 Ct10 196 200 270 ±0.13 ー 0.160 SRT1015-196R270C10 160 Ct10 196 200 270 ±0.13 ー 0.160
∼0.050 ∼0.050
SRT1010-396R470C10 370 Ct10 396 400 470 ±0.27 0.21 0.240 SRT1015-396R470C10 360 Ct10 396 400 470 ±0.27 0.21 0.240

Note ）Please refer to page A287 for order code of end-journal machining. Note ）Please refer to page A287 for order code of end-journal machining.

A309 A310
 Ball Scresw

Ball Scresw
Standard products in stock SRT series Standard products in stock SRT series

SRT1020 Shaft dia. φ10 Lead 20mm Ct7＆Ct10 SRT1202 Shaft dia. φ12 Lead 2mm Ct7＆Ct10
−ＳＲＴ１０２０ A11-SRT1202

4-φ4.5
23 4-φ4.5 24

（13） 5 30° 30° （19） 5 30° 30°

see below G

−0.05
φ25 −0.10
see below G
−0.05
φ20 −0.10

（φ11.7）
（φ9.9）

φ14.2
φ14.2

φ42

.5
34

.5
φ37
29 PCD

C0
C0
PCD

G G

.5
C0
22
L1 4 L1 4 27
L2 70 L2 70
L3 L3
Standard products in stock SRT/SSRT series

Standard products in stock SRT/SSRT series

Ａ１１−ＳＲＴ１０Unit
ｊ
ｏｕｒ ：mm
ｎａ
ｌ Ａ１１−ＳＲＴ１２ ｊ
ｏｕｒｎａ
ｌ
Unit：mm
Ball Screw Specifications End-journal profile Supported-side Fixed-side Ball Screw Specifications End-journal profile Supported-side Fixed-side

Ball size φ1.5875 A-type B-type C-type Ball size φ1.5875 A-type B-type C-type
0
10

φ11.5h8 −0.027
−0.2 0 M10×1.0

φ14h8 −0.027
Number of thread 4 M8×1.0 Number of thread 1 12 −0.25

φ8h6 −0.009
0

−0.002
φ10 −0.008
φ7.6 −0.08
φ6h6 −0.008
30°
×0.5
φ5.7 −0.06

−0.002
φ8−0.008
30°
×0.5

0
0

0
Thread direction Right Thread direction Right 5

−0.004
φ8 −0.012
−0.004
φ8−0.012
−0.002
φ6 −0.010

−0.002
φ6−0.010

Shaft root dia. φ8.7 Shaft root dia. φ10.6

R0.2max R0.2max R0.2max R0.2max R0.2max R0.2max

Number of circuit 0.7×4 L4＝L5ー49 0.8
+0.1
9 L4＝L5ー58 Number of circuit 3.7×1 +0.1
0 9 L4＝L5ー59 0.9 0 10 L4＝L5ー69 10
Shaft SCM415H＋SUS303 L5 6.8
+0.1
0 L5 27 10 Shaft SCM415H＋SUS303 L5 7.9
+0.1
0 L5 30 15
Material Material
Nut SCM415H 9 L4＝L5ー58 L4 4 8 37 Nut SCM415H 10 L4＝L5ー69 L4 4 10 45
L5 L5 L5 L5
Surface hardness HRC58∼ Surface hardness HRC58∼
（Thread area） L4：Thread length after end-journal machining. （Thread area） L4：Thread length after end-journal machining.
L5：Total length after end-journal machining. L5：Total length after end-journal machining.

Anti-rust treatment Anti-rust oil Supported-side ： MSU-8CS/8GS Anti-rust treatment Anti-rust oil Supported-side ： ー
Support-unit Recommendation Support-unit Recommendation
Fixed-side ： MSU-8C/8G Fixed-side ： ー
D-type : Other than the above. D-type : Other than the above.
Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L3 L1 L2 L3
ep V300 Ca Coa ep V300 Ca Coa

SRT1020-196R270C7 170 Ct7 196 200 270 ±0.03 ー 0.080 SRT1202-196R270C7 170 Ct7 196 200 270 ±0.03 ー 0.080
∼0.020 ∼0.020
SRT1020-396R470C7 370 Ct7 396 400 470 ±0.06 0.05 0.120 SRT1202-396R470C7 370 Ct7 396 400 470 ±0.06 0.05 0.080
ー 2100 4000 ー 3000 6400
SRT1020-196R270C10 170 Ct10 196 200 270 ±0.13 ー 0.160 SRT1202-196R270C10 170 Ct10 196 200 270 ±0.13 ー 0.160
∼0.050 ∼0.050
SRT1020-396R470C10 370 Ct10 396 400 470 ±0.27 0.21 0.240 SRT1202-396R470C10 370 Ct10 396 400 470 ±0.27 0.21 0.160

Note ）Please refer to page A287 for order code of end-journal machining. Note ）Please refer to page A287 for order code of end-journal machining.

A311 A312
Ball Scresw

Ball Scresw
Standard products in stock SRT series Standard products in stock SRT series

SRT1202K Compact Nut

Shaft dia. φ12 Lead 2mm Ct7＆Ct10 SRT1210 Shaft dia. φ12 Lead 10mm Ct7＆Ct10
A11-SRT1210

4-φ4.5 30 4-φ4.5
19
（14.5） 6 30°
see below G （14） 5 30° 30° see below G 30°

−0.05
φ24 −0.10
−0.05
φ19 −0.10

（φ11.75）
（φ11.9）

φ14.2
φ14.2

φ41

.5
.5
φ36
28 33

C0
C0
PCD PCD

G G
.5
C0

23 L1
L1 4 4 26
L2 60 L2 70

L3 L3
Standard products in stock SRT/SSRT series

Standard products in stock SRT/SSRT series

Ａ１１−ＳＲＴ１２ ｊ
Unit：mm
ｏｕｒｎａ
ｌ Ａ１１−ＳＲＴ１２ ｊ
ｏｕｒｎａ
ｌ
Unit：mm
Ball Screw Specifications End-journal profile Supported-side Fixed-side Ball Screw Specifications End-journal profile Supported-side Fixed-side

Ball size φ1.2 A-type B-type C-type Ball size φ2.381 A-type B-type C-type

0 M10×1.0 0 M10×1.0

φ14h8 −0.027
φ14h8 −0.027
Number of thread 1 12 −0.25 Number of thread 2 12 −0.25

φ8h6 −0.009
φ8h6 −0.009

0
0

−0.002
φ10 −0.008
−0.002
φ10 −0.008

φ7.6 −0.08
φ7.6 −0.08

30°
×0.5 30°
×0.5

0
0

0
Thread direction Right 5 Thread direction Right 5

−0.004
φ8 −0.012
−0.004
φ8 −0.012

−0.004
φ8−0.012
−0.004
φ8−0.012

Shaft root dia. φ11.0 Shaft root dia. φ10.2

R0.2max R0.2max R0.2max R0.2max R0.2max R0.2max

Number of circuit 1×3 +0.1 Number of circuit 1.7×2 +0.1
L4＝L5ー59 0.9 0 10 L4＝L5ー69 10 L4＝L5ー59 0.9 0 10 L4＝L5ー69 10
Shaft S55C＋SUS303 L5 7.9
+0.1
0 L5 30 15 Shaft SCM415H＋SUS303 L5 7.9
+0.1
0 L5 30 15
Material Material
Nut SCM415H 10 L4＝L5ー69 L4 4 10 45 Nut SCM415H 10 L4＝L5ー69 L4 4 10 45
L5 L5 L5 L5
Surface hardness HRC58∼ HRC58∼
L4：Thread length after end-journal machining. Surface hardness L4：Thread length after end-journal machining.
（Thread area） （Thread area）
L5：Total length after end-journal machining. L5：Total length after end-journal machining.

Anti-rust treatment Anti-rust oil Supported-side ： ー Anti-rust treatment Anti-rust oil Supported-side ： ー
Support-unit Recommendation Support-unit Recommendation
Fixed-side ： ー Fixed-side ： ー
D-type : Other than the above. D-type : Other than the above.
Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L3 L1 L2 L3
ep V300 Ca Coa ep V300 Ca Coa

SRT1202K-271R335C7 245 Ct7 271 275 335 ±0.04 ー 0.080 ∼0.020 SRT1210-196R270C7 165 Ct7 196 200 270 ±0.03 ー 0.080
ー 1600 3700 ∼0.020
SRT1202K-271R335C10 245 Ct10 271 275 335 ±0.19 ー 0.160 ∼0.050 SRT1210-396R470C7 365 Ct7 396 400 470 ±0.06 0.05 0.080
ー 5100 9800
Note ）Please refer to page A287 for order code of end-journal machining. SRT1210-196R270C10 165 Ct10 196 200 270 ±0.13 ー 0.160
∼0.050
SRT1210-396R470C10 365 Ct10 396 400 470 ±0.27 0.21 0.160

Note ）Please refer to page A287 for order code of end-journal machining.

A313 A314
Ball Scresw

Ball Scresw
Standard products in stock SSRT series Standard products in stock SSRT series

SSRT0601 Stainless
Shaft dia.φ6 Lead 1mm Ct7＆Ct10 SSRT0801 Stainless
Shaft dia.φ8 Lead 1mm Ct7＆Ct10

17 17
4-φ3.4 4-φ3.4
（13） 4 （13） 4
see below G see below G
30° 30° 30° 30°
-0.05
φ13 -0.10

-0.05
φ16 -0.10
（φ7.85）

φ14.2
（φ5.85）

.5
φ9.7
23

C0
.5

φ29
20 PCD

C0
φ26
PCD
.5

.5
G
C0

C0
16
L1 4 L1 4 18

L2 70 L2 70

L3 L3
Standard products in stock SRT/SSRT series

Standard products in stock SRT/SSRT series

Unit：mm Unit：mm
Ball Screw Specifications End-journal profile Supported-side Fixed-side Ball Screw Specifications End-journal profile Supported-side Fixed-side

Ball size φ0.8 A-type B-type C-type Ball size φ0.8 A-type B-type C-type
0
7 0
-0.2
M5×0.5 8 -0.2
Number of thread 1 Number of thread 1 M6×0.75

φ9.5h8 -0.022

φ4.5h6 -0.008
φ8h8 -0.022
φ3.7 ±0.03

φ4h6 -0.008
30°
×0.5 30°
×0．

0
5

φ5.7 -0.06

0
0

-0.001
φ6-0.006
-0.002
φ4 -0.010

-0.002
φ4 -0.010

0
-0.001
φ5 -0.006

0
3 3
Thread direction Right Thread direction Right

-0.002
φ6 -0.010

-0.002
φ6-0.010
Shaft root dia φ5.3 Shaft root dia φ7.3
R0.2ｍａｘ R0.2ｍａｘ R0.2ｍａｘ R0.2ｍａｘ R0.2ｍａｘ R0.2ｍａｘ
+0.1
Number of circuit 3.7×1 L 4＝L5 ー36 0.5 0 8 L4＝L 5 ー44 6.5 Number of circuit 3.7×1 L4＝L5ー41 0.8
+0.1
0 9 L4 ＝L5ー50 7

L5 5.35±0.05 L5 19 6 L5 6.8 +0.1 L5 22.5 7.5

Shaft SUS440C＋SUS303 Shaft SUS440C＋SUS303 0

Material 8 L4＝L5 ー44 L4 4 7 25

Material 9 L4 ＝L5 ー50 L4 4 7 30
Nut SUS440C Nut SUS440C
L5 L5 L5 L5
Surface hardness HRC55∼ Surface hardness HRC55∼
（Thread area） L4：Thread length after end-journal machining. （Thread area） L4：Thread length after end-journal machining.
L5：Total length after end-journal machining. L5：Total length after end-journal machining.

Anti-rust treatment Anti-rust oil Supported-side ： MSU-5CS/5GS Anti-rust treatment Anti-rust oil Supported-side ： MSU-6CS/6GS
Support-unit Recommendation Support-unit Recommendation
Fixed-side ： MSU-5C/5G Fixed-side ： MSU-6C/6G
D-type : Other than the above. D-type : Other than the above.
Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L3 L1 L2 L3
ep V300 Ca Coa ep V300 Ca Coa

SSRT0601-146R220C7 125 Ct7 146 150 220 ±0.02 ー 0.080 SSRT0801-196R270C7 175 Ct7 196 200 270 ±0.03 ー 0.080
∼0.020 ∼0.020
SSRT0601-261R335C7 240 Ct7 261 265 335 ±0.04 ー 0.120 SSRT0801-356R430C7 335 Ct7 356 360 430 ±0.06 0.05 0.120
ー 560 900 ー 630 1250
SSRT0601-146R220C10 125 Ct10 146 150 220 ±0.10 ー 0.160 SSRT0801-196R270C10 175 Ct10 196 200 270 ±0.13 ー 0.160
∼0.050 ∼0.050
SSRT0601-261R335C10 240 Ct10 261 265 335 ±0.18 ー 0.240 SSRT0801-356R430C10 335 Ct10 356 360 430 ±0.24 0.21 0.240

Note ）Please refer to page A287 for order code of end-journal machining. Note ）Please refer to page A287 for order code of end-journal machining.

A315 A316
Ball Scresw

Ball Scresw
Standard products in stock SSRT series Standard products in stock SSRT series

SSRT0802 Stainless
Shaft dia.φ8 Lead 2mm Ct7＆Ct10 SSRT1002 Stainless
Shaft dia.φ10 Lead 2mm Ct7＆Ct10

24 4-φ4.5 24 4-φ4.5

（19） 5 （19） 5 30°

30° 30° see below G 30°

-0.05
φ23 -0.10
see below G
-0.05
φ20 -0.10

（φ9.7）

φ14.2
φ14.2
（φ7.7）

.5
32

φ40
.5
φ37

C0
29 PCD

C0
PCD

G G
.5

.5
C0

C0
L1 4 22 L1 4 25

L2 70 L2 70

L3 L3
Standard products in stock SRT/SSRT series

Standard products in stock SRT/SSRT series

Unit：mm Unit：mm
Ball Screw Specifications End-journal profile Supported-side Fixed-side Ball Screw Specifications End-journal profile Supported-side Fixed-side

Ball size φ1.5875 A-type B-type C-type Ball size φ1.5875 A-type B-type C-type
0
8
0 10 -0.2 M8×1.0

φ11.5h8 -0.027
-0.2
Number of thread 1 M6×0.75 Number of thread 1

φ9.5h8 -0.022

φ4.5h6 -0.008

0
30°
×0.5

φ6h6-0.008
30°
×0．

0
5
φ5.7 -0.06

φ5.7 -0.06
0
-0.001
φ6-0.006

-0.002
φ8 -0.008
0

0
Thread direction Right 3 Thread direction Right 4
-0.002
φ6 -0.010

-0.002
φ6-0.010

-0.002
φ6 -0.010
-0.002
φ6 -0.010
Shaft root dia φ6.6 Shaft root dia φ8.6
R0.2ｍａｘ R0.2ｍａｘ R0.2ｍａｘ R0.2max R0.2max
R0.2max
Number of circuit 3.7×1 L4＝L5ー41 0.8
+0.1
0 9 L4 ＝L5ー50 7 Number of circuit 3.7×1 L4＝L 5 ー49 0.8
+0.1
0 9 L4＝L 5ー58 9

Shaft SUS440C＋SUS303 L5 6.8 +0.1

0 L5 22.5 7.5 Shaft SUS440C＋SUS303 L5 6.8
+0.1
0 L5 27 10
Material Material
Nut SUS440C 9 L4 ＝L5 ー50 L4 4 7 30 Nut SUS440C 9 L4＝L 5 ー58 L4 4 8 37
L5 L5 L5 L5
Surface hardness HRC55∼ Surface hardness HRC55∼
（Thread area） L4：Thread length after end-journal machining. （Thread area） L4：Thread length after end-journal machining.
L5：Total length after end-journal machining. L5：Total length after end-journal machining.

Anti-rust treatment Anti-rust oil Supported-side ： MSU-6CS/6GS Anti-rust treatment Anti-rust oil Supported-side ： MSU-8CS/8GS
Support-unit Recommendation Support-unit Recommendation
Fixed-side ： MSU-6C/6G Fixed-side ： MSU-8C/8G
D-type : Other than the above. D-type : Other than the above.
Unit：mm Unit：mm

Basic Load Rating Basic Load Rating

Shaft length Lead accuracy Shaft length Lead accuracy
N N
Preload Preload
Ball Screw Model Travel Grade Total Axial Torque Ball Screw Model Travel Grade Total Axial Torque
Run-out play Run-out play
Travel deviation Variation Nm Dynamic Static Travel deviation Variation Nm Dynamic Static
L1 L2 L3 L1 L2 L3
ep V300 Ca Coa ep V300 Ca Coa

SSRT0802-196R270C7 170 Ct7 196 200 270 ±0.03 ー 0.080 SSRT1002-196R270C7 170 Ct7 196 200 270 ±0.03 ー 0.080
∼0.020 ∼0.020
SSRT0802-356R430C7 330 Ct7 356 360 430 ±0.06 0.05 0.120 SSRT1002-396R470C7 370 Ct7 396 400 470 ±0.06 0.05 0.120
ー 1950 3100 ー 2200 4000
SSRT0802-196R270C10 170 Ct10 196 200 270 ±0.13 ー 0.160 SSRT1002-196R270C10 170 Ct10 196 200 270 ±0.13 ー 0.160
∼0.050 ∼0.050
SSRT0802-356R430C10 330 Ct10 356 360 430 ±0.24 0.21 0.240 SSRT1002-396R470C10 370 Ct10 396 400 470 ±0.27 0.21 0.240

Note ）Please refer to page A287 for order code of end-journal machining. Note ）Please refer to page A287 for order code of end-journal machining.

A317 A318