Desigo® Fire Safety Modular

System
Device Loop Card
Model XDLC

Architect & Engineer Specifications Product Overview

 Supports up to 252 addressable points The Siemens – Fire Safety `Class X’ Device Loop Card (Model XDLC) is the interface
used for connecting Siemens addressable, intelligent `X’ as well as `H’-series
 Operates and maintains all devices
devices.
residing on up to four (4) `Class A’, eight
(8) `Class B’ addressable circuits Each Model XDLC plugs into one (1) slot of the Model CC-2 or Model CC-5 card cage.
 Compatible with Siemens intelligent, Programming for Model XDLC is accomplished via the Desigo Fire Safety Modular
addressable ‘X’ and ‘H’-series devices: system custom-configuration tool, Zeus-D. Model XDLC takes one (1) address on
- Multi-criteria / Carbon Monoxide (CO) the network, communicating up to a total 252 detectors and devices. Model XDLC
Detector with ASAtechnologyTM has 16 LEDs for diagnostic purposes, and provides ground-fault detection and zone-
- Multi-criteria Detector isolation circuitry.
with ASAtechnologyTM
- Multi-criteria Detector Specifications
- Thermal (Heat) Detector The `Class X’ Device Loop Card (Model XDLC) initializes, operates and maintains all
- Input / Output Interface Module devices residing on up to four (4) `Class A’, eight (8) `Class B’ addressable circuits.
 Polarity insensitive (in non-isolation
Model XDLC communicates all relevant device and event data (`Alarm’, `Trouble’ and
mode) via SureWireTM technology: `Supervisory’ commands) to a Desigo Fire Safety Modular (Desigo Modular) fire-
- Modern technology supports alarm control panel (FACP), and supervises the device loop circuit.
comprehensive system and interface
communication
Model XDLC is polarity insensitive via SureWire technology, which greatly reduces
commissioning time normally spent tracing down crossed-field wiring. Model XDLC
 Quantity 16 diagnostic light-emitting communicates detector data, such as sensitivity of intelligent fire detectors and
diodes (LEDs) for easy circuit diagnosis logic-function information, to the Desigo Modular Operating Unit (Model FCM2041-
 Microchip controls on-board isolators U2), which is located within a given Desigo Modular system.
 Device Programmer / Tester Each device loop card supports four (4) `Class A’, eight (8) `Class B’ circuits for up to
(Model DPU) programs and verifies a total of 252 addressable devices – as well as relay and audible bases, remote lamps
device’s address:
and duct-detector housings in any combination.
- programming capabilities include
testing a duct detector, as well as The microprocessor in a Model XDLC controls the
other Siemens addressable devices on-board isolation, in case there is a fault (short) in
 Supports `Class B’ | `Class A’ | `Class X’ any of the circuits, thus allowing the other circuit
wiring to continue operating. For continuous protection,
 Supports T-Tapping
the on-board microprocessor continues to operate
even in the event of a CPU failure.
 Degrade mode
 UL864 | CAN / ULC Listed
NOTE: Refer to installation manual: P/N –
A6V101040156 to ensure Model XDLC
compatibility with the Siemens FACPs
intended for use in the given application.

Model XDLC d

Side View Model XDLC

d

Front View

Siemens Data Sheet 7312

Smart Infrastructure – Building Products usa.siemens.com/fire
 Model XDLC-
Diagram of an `Class X’ Device Loop Card
mounted to a Siemens Card Cage

Temperature and Humidity Range

`Class X’ Device Loop Cards are UL Listed | ULC Listed for indoor dry locations within a temperature range of 120+/-3°F
(49+/-2°C) to 32+/-3°F (0+/-2°C) and a relative humidity of 93+/-2% at a temperature of 90+/-3°F (32+/-2°C).

Technical Data Details for Ordering

24V CURRENT DRAW: MODEL PART
[Back Plane]
0 PRODUCT
OR TYPE NUMBER
24V CURRENT DRAW: 100mA + 1.4mA
`Class X’
[Screw Terminal] per device XDLC S54430-B8-A1
Device Loop Card
6.2V CURRENT DRAW:
1mA, max.
[Back Plane]
24V CURRENT DRAW: 100mA + 1.4mA
[Standby] per device

DEVICE LOOP: 500mA, max.

[@ 30 VDC Max.] (power limited)
xx

NOTICE – The information contained in this data-sheet document is intended only

as a summary, and is subject to change without notice.
The product(s) described here has/have a specific instruction sheet(s)
that cover various technical, limitation and liability information.
Copies of install-type, instruction sheets – as well as the General Product
Warning and Limitations document, which also contains important data,
are provided with the product, and are available from the Manufacturer.
Data contained in the aforesaid type of documentation should be consulted
with a fire-safety professional before specifying or using the product.

Any further questions or assistance concerning

particular problems that might arise, relative to the
proper functioning of the equipment, please contact
Desigo® Fire Safety
Siemens Industry, Inc.
the Manufacturer.
Smart Infrastructure - Building Products
2 Gatehall Drive • Parsippany, NJ 07054
Tel: (973) 593-2600
February - 2023
(Rev. 3)