FITTING INSTRUCTIONS • HONDA CRF1100L AFRICA TWIN - DCT (‘20 on)

for… • HONDA CRF1100L AFRICA TWIN - non DCT (‘20 on)

• HONDA CRF1100L AFRICA TWIN Adventure Sports - DCT (‘20 on)
www.barkbusters.net • HONDA CRF1100L AFRICA TWIN Adventure Sports - non DCT (‘20 on)
Preparation
Installation for Left Side. Repeat for Right side with applicable parts.
• Remove original factory handguard components if installed. Reattach the original brake & clutch lever screws with the flanged
spacers and nuts. Tighten the original screws to the manufacturer’s specified torque. Fit threaded insert (11) and tighten to specified torque setting.
• Remove original external handlebar end weights and metal clips. NOTE: Retain internal handlebar weights. Loosely assemble the clamp to the handlebar as per diagram. Attach
the handguard backbone with applicable parts to the handlebar end
and also to the clamp connector (5).
Riding Direction Left Side Left Side Parts: 9 & 10 for
DCT model ONLY
9 Note DCT models: Use bolt (9) & spacer (10) on LEFT side only.

4
Position backbone so it is horizontal when viewed from the side and
tighten all bolts in the following order: (13), (9 or 4), (7) then (8).

Important: Use the specified torque setting over page.

10
IMPORTANT: Make sure you have 2-3mm clearance
between weight (12) and throttle twist grip. Insert
8 supplied washer/s (17) if additional clearance is required. 17
5

3 11 12

16
7
7

Right Side

DCT Bracket Fitting DCT model ONLY: DCT model Bar Side View
1. Loosen park brake cable adjuster a few turns. ONLY
2. Remove original screw from the park brake lock 14

✓
and replace with screw (14) then tighten as specified.
PUSH 3. Mount Pressed Metal Bracket (15) between the
brake lever and parking brake sensor and secure with
PUSH Nut (16) as shown, then tighten as specified.

X
4. Set park brake cable adjuster to desired position
and secure.

IMPORTANT:
Position bracket (15) as shown in picture before
15
Check contact tightening.
with sensor. see image

Check the bracket makes contact with the sensor. 16

Slight repositioning of the sensor may also be
necessary.
INS-BHG-082-02-NP
1 2 3 4 5 6 7 8
Aluminium Bar - LEFT Aluminium Bar - RIGHT Multi Fit Clamp 28 Button Head Bolt 25mm Connector Connector Socket Head Bolt 20mm Socket Head Bolt 30mm

PN: BAR-V-039-L PN: BAR-V-039-R PN: MFC-28 PN: M8X25BHCSZP PN: CP8-L PN: CP8-R PN: M6X20SHCSZP PN: M6X30SHCSZP
Pcs. 1 Pcs. 1 Pcs. Set of 2 Pcs. 2 Pcs. 1 Pcs. 1 Pcs. 4 Pcs. 2

9 10 11 12 13 14 15 16
Button Head Bolt 35mm Spacer 10mm Threaded Insert Bar End Weight Flat Head Bolt 45mm Shoulder Bolt 30mm Pressed Metal Bracket Nylock Nut 6mm

PN: M8X35BHCSZP PN: BSSRT10 PN: BESF4 PN: BEW35 PN: M8X45FHCSZP PN: M6X30SB PN: BPM1 PN: M6LN
Pcs. 1 Pcs. 1 Pcs. 2 Pcs. 2 Pcs. 2 Pcs. 1 Pcs. 1 Pcs. 3

17 Personalise Your Protection

M8 Flat Washer
Guard options sold separately
JET-003
Recommended Torque Settings
NOTE: VPS-003
M6 10 Nm (7.4 lbf ft)
Part Numbers 9, 10, 14, 15
STM-003
& one of 16, required for M8 20 Nm (14.8 lbf ft)
PN: M8FW-SS DCT models only. M18 (item 11) 21Nm (15.5 lbf ft) BCF-003
Pcs. 2

CAUTION:
Installation of the handguard is safety-relevant work and can be complicated. We recommend the installation be performed by a motorcycle service technician.
Rideworx accepts no liability for damages caused by improper mounting. All screws, bolts and nuts, including all replacement hardware provided by Rideworx,
should be tightened to the torque specified in the table. After the first 50km of riding check all screws, bolts and nuts are tightened to the correct torque. We
recommend a medium strength liquid thread lock product on all fasteners. Email: [email protected]
Web: www.barkbusters.net
WARNING:
Check operation of all handlebar controls, specifically the throttle, front brake, kill switch and clutch to ensure they are operating correctly and are in accordance
with the OEM specifications. Do not ride the motorcycle if any controls are not operating correctly or if rear view mirror vision is obscured. Check periodically that
all bolts are tight.

Disclaimer:
A failure to follow these fitting instructions could cause serious injury, death or property damage. These handguards are intended solely for use with motorcycles/ATV/snowmobiles/scooters that have not been modified. They are not designed
to prevent injury or death while riding or in an accident or crash. The user must ensure that all controls are free of the handguards every time that they ride. By installing and/or using this product you acknowledge that you accept these terms
and have followed the fitting instructions.

INS-BHG-082-02-NP