Theory of metal cutting

Dr S B Patil
Assistant Professor Mechanical Engineering
College of Engineering, Pune 411005
[email protected]

1
 You should know
1. What do you understand by conventional manufacturing
processes? Explain how the conventional
manufacturing processes can be classified.
2. What do understand by conventional and non
conventional manufacturing process of manufacturing?
3. Explain the need of non conventional manufacturing
with the help of examples.
4. State and explain the parameters influencing machining
operation.
5. With the help of neat figure explain orthogonal and
oblique cutting operation.
6. With the help of neat figure explain the mechanics of
chip formation.
2
 Objectives of machining

1. Quick metal removal (or high MRR)

2. High class surface finish
3. Economy in tool cost
4. Less power consumption
5. Economy in cost of replacement and
resharpening of tool….

3
 Classification of manufacturing processes

1. Primary shaping processes

-Casting, forging, rolling, drawing, extrusion, squeezing,
shearing, piercing, forging
2. Machining processes
-Shaping, turning, milling, drilling, planning, grinding,
boring, knurling, sawing, broaching
3. Surface finishing processes
- Sand blasting, buffing, lapping, belt grinding, polishing,
honing, electroplating, metal spraying, anodizing,
phosphating, tumbling, galvanizing

4
 Classification of manufacturing processes

4. Joining processes
-Welding, soldering, brazing, riveting, screwing,
adhesive joining, pressing, coupling, key and cotter
joining, nut and bolts joints

5. Processes affecting change in properties

- Annealing, normalizing, hardening, tempering, grain
refining, age hardening

5
 Parameters influencing machining

1. Workpiece material- Chemical and physical properties

2. Cutting tool-Type, material, tool geometry

3. Cutting environment- Cutting fluid-type (chemical

composition and rate of flow)

4. Cutting parameters- Cutting speed, DOC, Feed

5. Machine tool- type, Rigidity

6
Basic elements of machining operation

7
Mechanics of chip formation

Rake Angle (γ)

Rake
Chip

Shear Zone Tool Flank

Clearance Angle (α)

8
• Chip formation is a complex phenomenon
• When tool is forced against the work piece, the crystals
are elongated
• The surface along which the chip slides is called rake
face
• The surface which is relived to clear the newly machined
surface is known as flank

• The rake face makes an angle (γ) with the normal to the
finished surface is called rake angle

• Clearance angle is the angle between the flank and new

work piece surface.

9
 Types of metal cutting operations

• Orthogonal cutting (Two dimensional cutting)

The cutting edge of the cutting tool is at right angles to
the direction of relative motion between tool and work
piece.
Example: Parting
• Oblique cutting (Three dimensional cutting)
The cutting edge of the cutting tool is inclined at an angle
to the direction of relative motion between tool and work
piece.
Example: Turning

10
Orthogonal cutting

11
 Orthogonal Cutting assumptions

1. The tool is perfectly sharp and there is no contact

along the clearance face

2. The Cutting edge of the tool remains normal to the

direction of tool feed or work feed.

3. The direction of the chip flow velocity is normal to the

cutting edge of the tool.

4. The cutting edge is a straight line, extending

perpendicular to the direction of motion and
generates a plane surface as the work moves past it.
12
Orthogonal &Oblique cutting

13
 Oblique cutting assumptions
1.The cutting edge of the tool always remains inclined at an
acute angle to the direction of tool feed or work feed
2. The direction of the chip flow velocity is at an angle ‘β’
with the normal to the cutting edge of the tool. The
angle is known as Chip flow Angle.
3. The cutting edge of the tool is inclined at an angle ‘i’ with
the normal to the direction of work feed or tool feed i.e.,
the velocity Vc.
4. Three mutually perpendicular components of cutting
forces act at the cutting edge of the tool.
5.The cutting edge may or may not be longer than the
width of the cut.
14
 You should know

1. “The quality of the chip determines number of important

aspects” Explain
2. What do you understand by tool signature. Explain with
the help of neat figure the tool signature of single point
tool.
3. Describe the various types of the chips produced during
machining operation with the help of neat figure.
4. Describe the various situations during which a particular
type of chip will be produced.
5. State the adverse effects of continuous chips with built
up edge formation and state the precautions required to
avoid.
15
Principle angles of single point tool

16
Tool signature

17
 Chip formation

• Cutting tool is required to be harder and wear

resistant than the work piece.

• Interface between the tool and the work piece is

designated as feed and depth of cut.

• Relative motion between the tool and workpiece

is termed as cutting speed or velocity to
overcome the resistance.

18
 Types of chips

• Size, shape and quality of the chip determines

number of aspects

1. Segmental or discontinuous chips

2. Continuous chips
3. Continuous chips with built up edge
4. Non homogenous chips

19
 Segmental or discontinuous chips

• Separate , plastically deformed segmental chips through

actual fracture

• This causes excessive friction between the chip and tool

face leading to fracture of the chip into small segments.

• Loosely adhere each other

• Produced during machining of brittle material
• Also produced during machining of ductile materials at
low speed and also with high DOC
• CI, Brass

20
 Segmental or discontinuous chips…

• This causes excessive friction

between chip and tool face,
leading to fracture of chip into
small segments.

• This will result in excessive tool

wear and poor surface finish.

• Other factors responsible:

smaller rake angle and large
depth of cut

21
 Continuous chips

• Continuous chips are produced due to continuous plastic

deformation of the metal ahead of the tool.

• The chips will be moving smoothly up the tool face.

• Need of chip breakers

• This type of chips will be produced while machining

ductile materials like copper, mild steel etc under
favorable cutting conditions such as high cutting speeds
and minimum friction at tool-chip interface
22
 Continuous chips

• The friction at chip-tool

interface can be minimized
by polishing tool face and
adequate use of coolant.

• Other responsible factors:

bigger rake angle, finer feed
and keen cutting edge.

23
 Continuous chips with built up edge

• While machining ductile materials

when high friction exists at the
chip-tool interface results in
continuous chips with built up
edge.

• The normal reaction of the chip on

the tool face is quite high and it is
maximum at the cutting edge or
nose of the tool.

24
 Continuous chips with built up edge
• This gives rise to an extensively
high temperature and compressed
metal adjacent to the tool nose
gets welded to it.

• The chip is sufficiently hot and

gets oxidized as it comes off the
tool and turns blue in colour.

• The extra metal welded to the

nose of the tool is called built up
edge.

25
 Continuous chips with built up edge

• Adverse effects of built up edge formation

- Rough surface finish

- Fluctuating cutting force, causing vibration in

cutting tool.

- Chances of carrying out tool material by built up

edge and crater formation on cutting tool face
and causing tool wear.
26
 Continuous chips with built up edge

• Precautions to avoid built up edge formation

- The coefficient of friction at the chip tool
interface should be minimized by means of
polishing the tool face.

- Adequate supply of coolant

- Larger rake angle

- High cutting speeds and low feeds

27
 Non homogenous chips

• Produced due to non-uniform strain in the

material during chip formation

• Characterized by notches on the free side

of the chip while adjoining the tool face is
smooth

28
Types of chips

29
 You should know

1. Explain the terms cutting ratio and chip compression

factor.
2. Derive an expression for cutting ratio/chip compression
factor in terms of shear plane angle and rake angle.
3. Derive an expression for shear plane angle in terms of
cutting ratio and rake angle.
4. State and explain the velocities during metal cutting.
5. Derive an expression for velocities along shear plane
and chip velocity in terms of cutting velocity, rake angle
and shear plane angle.

30
Cutting ratio or chip thickness ratio

31
Chip thickness ratio

32
 Cutting ratio (r)

• Cutting ratio is the ratio of thickness of the chip

before removal to thickness after removal from
the material being cut.
Chipthicknessbeforecutting
Cuttingratio(r ) 
Chipthicknessaftercutting

t1
r …… (1)

t2

33
 Chip compression/reduction factor

• The inverse of the chip thickness ratio is known

as chip compression factor or chip reduction
coefficient (k).

k= 1/r
• Cutting ratio is always less than unity. If the ratio
(r) is large, the cutting is good. A ratio of 1:2
yields good results.
•
34
35
36
37
38
Velocity relationships

39
40
 Velocities in metal cutting

i) Cutting velocity (v)

It is the velocity of the tool relative to the work piece and
directed parallel to the cutting force

ii) Chip velocity (vc)

It is the velocity of chip relative to the tool and is directed
along the face of the tool

iii) Shear velocity (vs)

It is the velocity of the chip relative to the work piece and
is directed along the shear plane
41
42
43
44
 You should know

1. With the help of neat sketch explain the various

component forces during orthogonal and oblique cutting
operations.
2. Draw Merchant circle diagram and label it. State the
various relationships.
3. What are the assumptions in Merchant’s theory?
4. Derive an expression for shear strain.
5. Explain work done and power requirement in metal
cutting.

45
 Forces in metal cutting

• In case of oblique cutting three

component forces act
simultaneously on the tool point .

1. Feed or thrust force (Ft or Fx )

acting in horizontal plane
parallel to the axis of the work.

2. Radial force (Fr or Fy )

acting in horizontal plane but
along the radius of the work
piece (along the axis of the tool).
46
 Forces in metal cutting

3. Cutting or tangential force (Fc or

Fz ) acting in the vertical plane
and is tangential to the work
piece.
The resultant force (R)

In case of orthogonal cutting Ft= 0

47
Merchant circle

48
49
50
51
 Merchant’s Theory
• For equilibrium, the force R between tool face and chip
and force R’ between work piece and chip along the
shear plane should be equal.

• For simplicity, forces R and R’ are assumed to act at the

tool point and represented by the diameter of the circle.

• Forces can be resolved as

i) In the horizontal and vertical direction, Fz & FY
ii) Along and perpendicular to the tool face, Fs & FD
iii) Along and perpendicular to the tool face FT & FN

52
 Merchant’s Theory…
• Fz is the main cutting force and is in the direction of
the tool travel. The feed force FY acts in direction
perpendicular to main cutting force Fz

• Force FS acts along shear plane and represents the

force required to shear material. Force FD acts
normal to Fs and results in compressive stress
being applied to the plane of shear

• Force FT acts along tool face and represents

frictional resistance met by chip as it slides over the
tool and FN is the force normal to FT.

53
54
55
56
57
58
59
60
61
62
Work done and power required in metal cutting

Let
v= cutting speed (m/min)
Fz= cutting force (kgs)
W= total work done in cutting
W= Fz X v ……. (1)
W1 = work done in shear
Fs = Shear force
vs = velocity along shear plane
W1 = Fs X vs …… (2)

63
 Work done and power required in metal cutting

W2 = work done in friction

Ft = Shear force
vc = chip velocity
W2 = Ft X vc …… (3)

W= W1 + W2
Fz X v = Fs X vs + Ft X vc

Let P= Power in metal cutting

P= Fz X v /4500 H. P.

64
65
 You should know

1. What are the desirable properties of cutting tool material?

2. State the different types of materials used for cutting tool and
describe them.

3. State the properties of the cemented carbide tools due to which

they are used as common industrial cutting tools.

1. Describe the following as industrial cutting tool

a. Cemented carbide tools

b. Ceramic tools
66
 Cutting tool materials
• Cutting tool has to be harder than the work material

• Desirable properties of cutting tool

1. It should be rigid enough to withstand the forces being applied due

to cutting- broaching

2. It should be tough (resistant to shock loads). It is quite important

when tool is used for intermittent loads.

3. It should be sufficient harder (resistant to wear, abrasion, and

indentation) than the material being cut.

67
 Cutting tool materials…
4. It should be able to withstand high temperatures.

5. It should be capable of withstanding the sudden cooling effect of

coolant used during cutting.

6. The coefficient of friction between the chip and the tool should be as
low as possible in the operating range of speed and feed.

7. It should be easily formed to the required cutting shape.

68
 Types of Cutting tool materials
1. Carbon tool steel

2. Alloy steel

3. High speed steel

4. Stellite

5. Cemented carbides

6. Ceramics or Cemented oxides

7. Diamonds

69
 1. Carbon tool steel
- Plain carbon steels having carbon % as high as 1.5%
are commonly used as tool for general class of work.

- As the operating temperature range is just 250°- 300° C

-not suitable for industrial production, also have less
wear resistance.

- These tools can be used as hand tools or cutting soft

materials or at low cutting speeds.

- These tools are less costly, easily forgeable and easy

to heat treat.

70
 2. Alloy steel

• Medium alloy steel are similar to carbon tool steel,

however in medium alloy steels elements like chromium,
molybdenum and tungsten are added to improve certain
properties such as hardenability, wear resistance etc

• Plain carbon steel if added with alloying elements such

as chromium, vanadium, tungsten, cobalt, nickel, silicon,
etc we will get En series
such as En-8, En-24, En-30, En-31, En-36, En-56

71
 3. High Speed Steel (HSS)

• It is a special alloy which may contain the alloying

elements like tungsten, chromium, vanadium, cobalt,
molybdenum etc up to 25%

• these alloying elements increase its strength, toughness,

wear resistance, cutting ability to retain its hardness at
elevated temperature of 550º - 600º C.

• Have the capability of operating 2 to 3 times higher

cutting speeds than those of high carbon steels.

72
 3. High Speed Steel (HSS)

• The most commonly used HSS is better known by its

composition of alloying elements as 18-4-2 i.e. 18%W,
4%Cr and 2% V.

• Another class of HSS contains high proportion of cobalt

(2-15%) and known as cobalt HSS. It has high wear
resistance and hot hardness.

• A highly tough variety of HSS is known as vanadium

HSS carries 2% V, 6% W, 6% Mo & 4% Cr. This HSS is
highly favoured for tools which have to bear impact
loading and perform intermittent cutting.

73
 3. High Speed Steel (HSS)…

• Sometimes HSS tools are treated to improve its

performance

Super finishing- to reduce friction

Chromium electrolytic plating- to reduce friction

Oxidation- to reduce friction

Nitriding- to increase wear resistance

74
 4. Stellite
• It is a non-ferrous alloy consisting of cobalt, tungsten and
chromium, other elements added in varying proportion
are tantalum, molybdenum and boron.

• It has good shock and wear resistance and retains its

hardness up to 920° C

• These are used to machine materials like hard bronzes,

and cast and malleable iron etc

75
 Stellite
• Tools made of stellite are capable of operating at speeds
up to 2 times more than those of common HSS tools

• Stellite does not respond to usual heat treatment

process and also it can not be easily machined by
conventional methods only grinding can be used for its
machining.

• A stellite may contain 40-50% Co, 15-35% Cr, 12-25%

W and 1-4% C.

76
 5. Cemented or sintered carbides

• Manufactured by powder metallurgy

• Consists of tungsten, tantalum, and titanium carbides
together with a binder cobalt.

• Compacted to the desired shape and sintered. During

the process the cobalt binder fused to the carbides
producing a hard and dense substance

• Cemented carbides are extremely hard (90-93 HRC) and

can be used at cutting speeds 200 to 500% greater than
those used for HSS.

77
 5. Cemented carbides…

• Usual practice is to confine the size to a relatively small

shape known as “insert”. Which is clamped/brazed to a
tough steel shank or holder .

• Inserts may have 3 to 8 edges and is so designed that

each of its cutting edges can be used in turn.

• These cemented carbides posses a very high degree of

hardness and wear resistance and diamond is the only
material harder than it.

• It retains its hardness up to 1000° C

78
 Properties of cemented carbide tools

1. They have high thermal conductivity, low specific heat

and low thermal expansion.

2. They have high hardness and over a wide range of

temperature (900º C).

3. Their compressive strength is more than tensile

strength.

4. They are very stiff and their Young’s modulus is about

three times than the steel

79
 5. Ceramic tools
• It mainly consists of Al2O3 which is cheaper than any of
the main constitute of cemented carbides.

• Boron nitrides in powdered form are added and mixed

with aluminum oxide powder and sintered at 1700º C.

• They are compacted in different shapes. Usually used

in the form of disposable tips (throw away tips)

• These tools have capability to withstand high

temperature 1200° C.

80
 5. Ceramic tools
• These tools have better wear resistance as compared
to cemented carbide tools.

• But they are brittle and posses low resistance of

bending as a result can not be employed for rough
machining and intermittent cutting.

• However, their application for finishing operations yields

very satisfactory results.

81

• .
 5. Ceramics…

• Can be operated at 2 to 3 times higher cutting speeds

than the tungsten carbide tools and usually do not
require coolant .
• Can be used to cut at the top speeds up to 1500m/min

• Ceramics are very hard and with good compressive

strength.

• Under similar conditions, the ceramic tool are capable

of removing (MRR) 4 times material than the tungsten
carbide tool with a consumption 20% less power than
latter.
82
 5. Ceramics…

• Three types of ceramic tools are common in use

i. Al2O3 ceramic tools- the most common in use and

used for finishing and super finishing operations

ii. Sialon (a combination of silica, aluminum, oxygen

and nitrogen)

iii. Silicon nitride (Si3N4)

83
 6. Diamonds

• The hardest material ever known

• It is brittle and offers a low resistance to shock, but is

highly wear resistance

• It has low coefficient of friction, and high compressive

strength.

• It gives very good surface finish at high speeds with

good dimensional accuracy.

84
 6. Diamonds

• Diamonds are employed for only light cuts and finishing

operations on material like Bakelite, plastics, glass ,
ceramics, carbon, plastics, aluminum and brass etc

• However, on account of their excessively high cost, its

use in industry is confined.

• Other applications includes dressing of grinding wheels.

• Diamond particles are used in diamond wheels and

laps.
85
 You should know
1. State and describe the causes of heat during machining.

2. Explain with the help of neat diagram the sources of heat during
metal cutting.

3. State and describe the various functions of cutting fluid.

4. State the desirable properties of cutting fluid.

5. State the various types of cutting fluids used during metal cutting
and describe them.

6. List out the various factors which affect on the selection of cutting
fluid
86
 Causes of heat in metal cutting

• Heat in metal cutting is produced due to

1. Friction

2. Plastic deformation of metal

3. Chip deformation

87
 Causes of heat in metal cutting

1. Friction

- Lot of friction is always takes place between the

cutting tool and work piece and chips passing over it.

-The total amount of heat generated depends on many

factors such as cutting parameters, tool material etc.

- This heat is called as heat of friction

88
 Causes of heat in metal cutting

2. Plastic deformation of metal

- As the cutting is started, the cutting tool exerts
significantly high pressure on the adjacent metal grains.

- This causes deformation or slipping of these grains over

adjacent layers in contact causes friction between them

- This friction leading to heat generation is known as heat

of deformation.

-The total heat generated depends on many factors such

as cutting parameters, work piece material etc.
89
 Causes of heat in metal cutting

3. Chip distortion
- In metal cutting, as the cutting proceeds and the chip curl
out, the inside grains of the chip metal are subjected to
compression and tension respectively.

- This causes distortion of the chip grains leading to internal

friction among them results the generation of heat.

- This heat is also called heat of chip distortion.

- The amount of heat generated depends largely on feeds

and depth of cut
90
 Sources of heat in metal cutting

Heat during metal cutting is produced at

1. Around shear plane

2. Tool-chip interface

3. Tool work piece interface

91
 Sources of heat in metal cutting

1. Around shear plane

(Primary deformation zone)
It is the region in which
actual deformation occurs
during machining which
results in heat generation.

A part of this heat is carried

away by the chip and rest of
heat is retained by the work
piece.

92
 Sources of heat in metal cutting
2. Tool-chip interface
(Secondary deformation zone)
As the chip slides upward during face of
the tool friction occurs between their
surfaces due to which heat is
generated.

A part of this heat is carried away by the

chip due to which temperature
increases and rest to tool.

The amount of heat is generated due to

friction increases with increase in
cutting speed.

93
 Sources of heat in metal cutting

3. Tool work piece interface

That portion of tool flank which
rubs against the work surface
is another source of heat
generation due to friction.

The heat is also shared by tool

and work piece.

The heat increases when the

tool is not sufficiently sharp.

94
 Sources of heat in metal cutting
- On an average 70% of the total
heat is carried out by chip, about
15% is transferred to the tool and
remaining 15% to the work piece.

- With an increase in the cutting

speed a higher amount of heat is
absorbed by the chip and lesser
amount of heat is transferred to tool
and work piece.

- A large value of shear angle leads

to smaller heat generation in
primary deformation zone.
95
 Cutting fluids
• The use of the metal working fluids is essential
in all metal working operations.

• In metal cutting, a lot of heat is generated proves

harmful to the tool and work piece.

• These fluids help in minimizing these adverse

effects of heat and thus helps in increasing tool
life and surface finish.

96
 Functions of cutting fluids

1. It cools the cutting tool and work piece by carrying away

the excessive heat.

2. It lubricates the cutting tool and thus reduces the

coefficient of friction between the chip and tool. This
increases the tool life.

3. To prevent the adhesion of chips to the tool or work or

both

97
 Functions of cutting fluids

1. To cool the tool and work piece

- The cutting fluid employed at low temperature, as

compared to the temperature of the tool, work and chips

- The heat generated flows from them outwards the fluid,

which absorbs and drives it away along with it.

- The fluid is thus heated up and needs a constant

replacement by a fresh amount of cooler fluid.

- For this reason only a steady flow of the cutting fluid in

ample quantity is always needed during machining.
98
 Functions of cutting fluids

2. To provide lubrication

- It implies the reduction of friction between the tool and

work piece and tool and chips.

- This helps in preventing a direct metal contact amongst

the work piece, tool and the chip (film lubrication) which
reduces friction.

- A lesser amount of heat is generated and less power is

consumed in machining.

99
 Functions of cutting fluids

3. To prevent adhesion of chips to the tool or work or both

- To prevent this, the addition of chemically active agents,

like compounds of sulfur or chlorine are made to the
cutting fluids.

- The compounds produce soapy films between the work

and tool and chip and tool face which prevents direct
contact and hence chances of welding or adhesion.

- This film also provides lubrication, called metal

lubrication between the mating surface.
100
 Desirable properties of cutting fluids

1. It should have a high specific heat, high thermal

conductivity and high film coefficient.

2. It should posses good lubricating properties to reduce

frictional forces and to decrease the power consumption

3. It should be odorless.

4. It should be non corrosion to work and machine

101
 Desirable properties of cutting fluids…

5. It should be non toxic to the operating personnel.

6. It should posses low viscosity to permit free flow .

7. It should be stable in use and storage.

8. It should permit clear view of work which is specially

desirable in precision work.

9. It should be safe particularly with regards to fire and

accident hazards.
102
 Types of cutting fluids…

• A cutting fluid mainly severs the following functions

i. Cooling
ii. Lubrication and
iii. Antiwelding

Types of cutting fluids

i. Water based cutting fluids
ii. Straight or neat oil based cutting fluids
iii. Lubricants

103
 Water based cutting fluids

• Water based cutting fluids are very common in use

• The most common in use is soluble oil which is mixed

(1 to 5%) to form emulsion.

• It has excellent cooling properties and good lubrication

effect.

104
 Water based cutting fluids…

• Modern soluble oil contain corrosion inhibitor and a

biocide to keep down the growth of bacteria that would
otherwise cause health hazard.

• Soda solutions are often used for grinding operations as

it has good flushing action and cooling effect.

• Water itself is seldom used as coolant as it causes rust

and corrosion.

105
 Straight or neat oil based cutting fluids

The term straight when applied to lubricants and

coolants means diluted.
Types of straight or neat oil based cutting fluids

1. Mineral oils
2. Straight fatty oils
3. Compounded or blended oils
4. Sulphurized oils
5. Chlorinated oils

106
 Straight or neat oil based cutting fluids…

1. Mineral oils
- Used for light machining operations
- machining of free cutting brass and steel

2. Straight fatty oils

- the most common is lard oil
- these oils are not stable and rapidly lose their
lubricating properties
-Neither they are satisfactory coolants as they have
high viscosity.
-Mainly used during cutting with taps and dies.
107
 Straight or neat oil based cutting fluids…
3. Compounded or blended oils
-Mixture of mineral oil (75%) and fatty oils (25%)
-They are very cheaper than fatty oils
- Suitable for heavy duty operations
4. Sulphurized oils
-5% Sulphur is added to lard oil so it is called as Sulphurized oil
- Used for heavy duty operations
5. Chlorinated oils
-About 3% chlorine is added to mineral oils.
- When chlorine and sulphur (5%) are present in mineral oil, they
give good lubricating properties and are suitable for machining of
strong and tough materials
-very often used for broaching

108
 Lubricants

• Solid lubricants are employed in a finely divided state

and are kept in suspension in the liquid form by means
of a depressing agent.

• Under certain conditions the lubricants reduces friction

on the tool face and reduces power consumption,
increases tool life and surface finish.

109
 Factors affecting selection of cutting fluid

1. Cutting speed, feed and depth of cut

2. Cutting tool material
3. Work piece material
4. Viscosity of cutting fluid
5. Expected tool life
6. Cost of cutting fluid

110
 Selection of cutting fluid

• Low speed and shallow cuts require little cooling or

lubricants.
• A lubricant of considerable oiliness is required while
machining of tough materials at low speeds and heavy
cuts.
• Shallow cuts at high speed require good coolants
therefore emulsions of soluble and sulphur base cutting
oils are employed.
• Brittle materials like cast iron are often cut without the
use of a lubricant although emulsions of soluble oil in
water are sometimes used
111
 Selection of cutting fluid

Sr. Operation Cutting conditions and other Suggested fluids

No. requirements
1 Turning Process parameters and material Emulsion or
being cut straight oils
2 Sawing For cleaning saw teeth, and carry Soluble oils
away chips
3 Tapping and Lubrication as cutting speeds are Fatty oils
threading low
4 Drilling and Lubrication and cooling Soluble oils
boring
5 Reaming Lubrication Soluble oils
6 Broaching Heavier cuts are taken Heavy and active
type of cutting oils

112
 Selection of cutting fluid

Sr. Operation Cutting conditions and other Suggested fluids

No. requirements
7 Planing and --- No cutting oils
shaping
8 Milling Cooling, lubrication and prevent tool Sulphurized
chatter mineral oil in
ample quantity
9 Thread rolling --- Straight mineral
oil or emulsions
10 Gear cutting, --- Active type
shaping and mineral oils and
shaving compounds
11 Grinding, Lubrication Active type
lapping and mineral oils and
honing compounds
113
 Selection of cutting fluids

Material Cutting fluids

Steel and wrought iron Water soluble oils or sulphur based

mineral oils

Aluminum Mineral oils and fatty oils or soluble

oils

Brass, copper , bronze, malleable iron Soluble oils

Cast iron Dry machining

114
 You should know
1. State the various symptoms of unsatisfactory cutting.
2. What are the causes of tool failure. Explain the following in detail
a. Thermal cracking and softening
b. Mechanical chipping

3. With the help of neat diagram explain the following in detail

a. Crater wear
b. Flank wear
4. Explain the following wear mechanism responsible for tool wear
a. Adhesion
b. Abrasion
c. Diffusion and
d. Chemical wear

115
 Unsatisfactory cutting

A properly designed and ground cutting tool is expected to

perform satisfactory.
The tool when it is not performing satisfactory then
following adverse effects may be observed
1. Extremely poor surface finish
2. Higher consumption of power
3. Work dimensions not being produced
4. Overheating of cutting tool
5. Appearance of a burnishing band on the work piece

116
 Causes of tool failure

A tool may fail during an operation or perform

unsatisfactorily due to

1. Thermal cracking and softening

2. Mechanical chipping

3. Gradual wear

117
 Causes of tool failure
1. Thermal cracking and softening
- Due to heat the tool tip and the area closer to the
cutting edge becomes very hot and the tool starts
loosing its hardness after attaining some temperature.
- After the operating temperature, the tool material starts
deforming plastically at the tip and adjacent to the
cutting edge under the action of the cutting pressure
and the high temperature.
- Thus the tool loses its cutting ability and is said to have
failed due to softening.
- Factors responsible: high values of cutting parameters,
smaller nose radius and selection of wrong tool material
118
 Causes of tool failure

• Thermal cracking and softening

- On the account of fluctuations in temperatures and severe
temperature gradients the
tool material is subjected to
local expansion and
Contraction.
- This results in development of thermal stresses due to
which thermal cracks are developed in the material.
- The tool failure due to this aspect is known as failure
due to thermal stresses.

119
 Causes of tool failure

2. Mechanical chipping
- Mechanical chipping of the nose
and/or the cutting edge of the tool
are commonly observed.
- Chipping occurs due to high cutting
pressure, mechanical impact,
excessive wear, high vibration and
weak tip and cutting edge etc.
- Chipping is more pronounced in carbide tipped and
diamond tools due to their high brittleness.

120
 Causes of tool failure

3. Gradual wear
- Loss of mass from tool is
due to wear
- Two types of wear
generally found in
cutting tools

1. Crater wear

2. Flank wear
121
 Crater wear

• The principal region where

wear takes place in a cutting
tool is its face, at a small
distance ‘a’ from its cutting
edge.

• This type of wear takes place

while machining ductile
materials, where continuous
chips are produced.

122
 Crater wear

• The resultant feature of this is

the crater or depression at the
tool chip interface.

• This type of wear is due to the

pressure of the hot chip
sliding up the face of the tool.

• The metal from the tool face is

supposed to be transferred to
the sliding chip by means of
diffusion process.

123
 Crater wear

• The shape of the crater

formed corresponding to the
shape of the underside of the
chip.
• The principal dimensions of
the formed crater are its
breadth ‘b’ and depth ‘d’.
• A continued growth of crater
will result in the cutting edge
of the tool becoming weak
and finally lead to tool failure.

124
 Crater wear

• At very high speed, and the

consequent high temperatures
(say 1000° C), the HSS tool
fail due to thermal softening of
material, while the tools made
from harder materials, like
those containing tungsten
carbide, cobalt etc will not
wear so rapidly.
• Higher feeds and lack of
cutting fluid increases the rate
of crater wear.
125
 Flank wear
• Another region where an
appreciable amount of wear
occurs is the flank below the
cutting edge.

• It occurs due to abrasion between

the tool flank and the work piece
and excessive heat generated as
a result of the same.

• The abrasive action is aided by

the hard micro constituents of the
cut material.
126
 Flank wear
• The entire area subjected to flank
wear is known as wear land.
.
• This type of wear mainly occurs
on the tool nose, front and side
relief faces.

• The magnitude of this wear

mainly depends on the relative
hardness of the work piece and
tool materials at the time of
cutting operation and also the
extent of strain hardening of the
chip.
127
 Flank wear

• When the tool is subjected to

this type of wear, the work
piece loses its dimensional
accuracy, energy
consumption is increased
and the surface finish is
poor.

128
 Flank wear

The effect of flank wear is expressed in

Terms of width (or height) of wear land
which is dependent on time.

This height is a linear measure and

expressed in mm

129
 Flank wear

• The total flank wear consists of

three components, drawn
between the wear land height
(VB) and time (t).

• The first component (A) which

exists for a small duration,
represents the period during
which initial wear takes place
at a rapid rate.

130
 Flank wear

• The second segment (B),

which exists for a very long
duration, represents the period
during which the wear
progress uniformly.
• The last segment (C)
represents the region in which
wear occurs at a very rapid
rate and results in tool failure.
• Thus the region is known as
period of destructive wear.

131
 Effect of cutting speed on flank wear

• Effect of cutting speed on the tool flank wear (VB) for

three cutting speeds, using a tool life criterion of 0.50
mm flank wear.

132
 Wear mechanism

• The wear mechanism of

cutting tool is a complex
phenomenon.
• The common
mechanisms responsible
for wear are
1. Abrasion
2. Adhesion
3. Diffusion
4. Chemical wear

133
 Wear mechanism- Abrasion

• It is a type of mechanical wear.

• Under this mechanism, hard particles on the underside

of the sliding chip, which are harder than the tool
material, plough into the relatively softer material of the
tool face and remove metal particles by mechanical
action.

• The material of the tool face is softened due to the high

temperature.

134
 Wear mechanism- Abrasion

• The hard particles present on the underside of the chip

may be:

a. Fragments of hard tool material

b. Broken pieces of built up edge, which are strain

hardened.

c. Extremely hard constituents like carbides, oxides, scales

etc present in the work material.

135
 Wear mechanism- Adhesion

• Due to excessive pressure a lot

of friction occurs in between the
sliding surfaces of the chip and
tool face.
• This gives rise to an extremely
high localized temperature,
causing metallic bond between
the materials of the tool faces
and the chip
• But, the surfaces which are
actually microscopically rough
produces point contacts.
136
 Wear mechanism- Adhesion

• Due to extremely high

temperature at the tool-chip
interface a metallic bond in
between chip and tool material
takes place at the contact
points in the form of small spot
welds.
• When the chip slides, these
small welds are broken. But this
separation is not along the line
of contact.

137
 Wear mechanism- Adhesion

• A small portion of the welded

tool contact is also carried away
by the sliding chip.
• Thus, small particles from the
tool face continue to be
separated through this
phenomenon so transferred
from the tool face to the chip
will depended upon the contact
area and relative hardness of
chip and the tool material.

138
 Wear mechanism- Diffusion
• Solid state diffusion, which consists of transfer of atoms
in a metal crystal lattice, is another cause of wear.

• This transfer of atoms takes places at elevated

temperature from the area of high concentration to that
of low concentration.

• The favorable condition for diffusion is provided by the

rise in localized temperature over the actual contract
area between the chip underside and the tool faces.

139
 Wear mechanism- Diffusion
• In such a condition, the tool material to the chip material
at the points of contact.
• This weakens the surface structure of the cutting tool
and may ultimately lead to tool failure.
• The amount of diffusion depends upon:

a. Temperature at the contact area between the tool faces

and the chip
b. The period of contact between the tool face and chip
c. The bonding affinity between the materials of the tool
and the chip.

140
 Wear mechanism- Chemical wear
• This type of wear occurs when such a cutting fluid is
used in the process of metal cutting which is chemically
active to the material of the tool.

• This is clearly the result of chemical reaction taking

places between the cutting fluid and the tool material,
leading to a change in the chemical composition of the
surface material of tool.

141
 You should know

1. What do understand by “Machinability”? List out the various factors

on which Machinability depends on.
2. List out the possible Machinability evaluation criterions.
3. Write short note on “Machinability index”.
4. Write short note on
1. Economics of metal cutting
2. Relationship between cutting speed, production rate, and cost
3. High efficiency range for cutting speed
4. Optimum cutting speed
5. Efficient metal removal
5. What could be the possible through which metal removal rates can
be improved?

142
 Machinability

• Machinability of a material gives the idea of the ease

with which it can be machined.

• The parameters generally affecting the machinability of

material are:
1. Physical properties of the material
2. Mechanical properties of the material
3. Chemical composition of the material
4. Micro-structure of the material
5. Cutting conditions

143
 Machinability evaluation
1. Rate of metal removal per tool grind

2. Tool life between successive grinds

3. Magnitude of cutting forces

4. Quality of surface finish

5. Shape and size of chips

6. Temperature during cutting

7. Power consumed

144
 Machinability index

• The machinability for different materials are compared

in terms of their machinability index.

• For this purpose the machinability index of free cutting

steel serves as datum and it is taken as 100.

• The machinability of the material can be computed as

145
 Economics of metal cutting
• One of the basic objective of metal cutting is producing
at minimum possible cost.
• The objective may be achieved through different
possible ways such as optimizing tool life, increasing
MRR etc.
• In order to achieve maximum tool life the values of
process parameters are required to be the minimum.
• Cutting speed among the process parameters has the
highest bearing on tool life.
• Thus there is need to determine optimum cutting which
maximizes the tool life.

146
 Optimum cutting speed

• It is observed that the

tooling cost increases while
the machining cost
decreases with increase in
cutting speed.
• The lowest point ‘P’ on the
curve determines the
minimum cost of
production. And the
corresponding cutting
speed gives the optimum
cutting speed.
147
 Optimum cutting speed

• The production cost per

piece (Km) is the minimum
• Total production cost of
component comprises
several components such
as
1. Machining cost
2. Tool changing cost
3. Tool sharpening cost
4. Idle cost …

148
 Relation between cutting speed, production rate
and cost

• Figure shows the plots for

minimum cost and maximum
production.
• It is found that the optimum
cutting speed for which the
production cost is minimum is
not same for the highest
production rate.

149
 Relation between cutting speed, production rate
and cost

• The area lying in between

these two values of cutting
speeds is known as high
efficiency range (Hi-E Range)
and the cutting speeds lying in
this range are either
economical or more
productive.
• For efficient and economical
production cutting speed is
required to be selected from
this range.
150
 Efficient metal removal

1. Optimum cutting speeds

- tool costs are reduced
- production rates are improved
2. Highest feed rate and depth of cut
- productivity is improved
3. Largest nose radius
- surface of the work piece is improved
- heat dissipation is better
4. Optimum tool geometry

151
 You should know

1. What do understand by tool life? Explain

2. State and explain the various methods of expressing
tool life.
3. Explain volume of material removed as a method of
calculating tool life.
4. Sate the various factors affecting tool life and describe
them in detail.
5. Explain Taylor’s tool life equation.

152
 Tool Life

• Tool life can be defined as the time interval for which

the tool works satisfactorily between two successive
grinding (sharpening).

• When the tool wear is increased considerably, the tool

loses its ability to cut efficiently and requires to be
reground.

• The tool life can be effectively uses as the basis to

evaluate the performance of the tool material, assess
machinability of the work piece.

153
 Methods of expressing Tool Life

• There are three common methods of expressing tool

life.

1. As time period in minutes between two successive

grindings.
2. In terms of number of components machined between
two successive grindings. This method is used when
the tool operates continuously, as in case of automatic
machines
3. In terms of volume of material removed between two
successive grindings. This method is commonly used
when the tool is primarily used for heavy stock removal.
154
Tool Life- Volume of material removed

155
Tool Life- Volume of material removed

156
Taylor’s Tool Life equation

157
 Factors Affecting Tool Life

1. Cutting speed
2. Feed and depth of cut
3. Tool geometry
4. Tool material
5. Work material
6. Nature of cutting
7. Rigidity of machine tool
8. Use of cutting fluid

158
1. Effect of cutting speed

159
2. Feed and depth of cut

160
 3. Tool geometry- Rake angle

• Many tool angles influence tool life such as Rake angle

has a mixed effect.
• If it is increased in a positive direction the cutting force
and the amount of heat generated will reduce and hence
tool life increases.
• But if it is very large then the cutting edge is weakened
and also the capacity to conduct heat is reduced.
• Hence the optimum range for rake angle is -5° to +10°
• Cemented carbide and ceramic tools are generally
provided with negative rake angle.

161
 3. Tool geometry- Clearance angle

• Clearance angle is provided on tool to reduce rubbing

action of tool to newly generated surface.
• Large value of clearance angles results in weakening of
tool and hence results in reduced tool life.
• Smaller value of clearance angles will lower the heat
generated during the cutting but tool may rub against the
work piece.
• Hence the optimum range for clearance angle is 5° to 8°,
but in special cases, such as in carbide tipped tools, a
higher value up to 10° is used to prevent the rubbing of
shank.

162
 3. Tool geometry- End cutting edge angle

• The two cutting edge angles have their influence on tool

life.
• The front cutting edge angle also known as end cutting
edge angle effects tool wear..
• Up to a certain optimum value an increase in this angle
permits the use of higher cutting speeds without adverse
effect on tool life.
• But an increase beyond that value will result in reduction
in tool life.
• It generally varies from 5° to 8°.

163
 3. Tool geometry- Side cutting edge angle

• The side cutting edge angle or the plane

approach angle has a complex effect on tool life.

• If this angle is smaller, higher speeds can be

employed.

• A larger side cutting edge angle increases tool

life.

164
 3. Tool geometry

• Some other geometrical parameters affecting the tool life

are
a. Inclination angle- Tool life increases with the increase in
this angle t an optimum value.

b. Nose radius- while it increase abrasion, it also helps in

improving surface finish and tool strength and the tool
life.

165
 5. Work material

• The microstructure of the work material has significant

effect on the hardness of material.
• For example presence of free graphite and ferrite in cast
iron and imparts softness to them.
• Pearlitic structure is harder than ferrite and martensitic is
the hardest.
• Similarly scale formation and presence of oxide layer on
the work surface serve as abrasives and therefore have
detrimental effect on tool life.

166
 5. Work material

• Consequently, higher the hardness of the work material

greater will be the tool wear and shorter will be tool life.
• Adverse effects on tool life are also experience in pure
metal as they have tendency to stick to the tool face,
specially at higher temperatures.
• This results in more friction and hence high amount of
wear on tool and therefore a shorter tool life.

167
 6. Nature of cutting

• Tool life is also affected by nature of cutting i.e.

continuous or intermittent.
• In case of intermittent cutting the tool is subjected to
repeated impact loading and may give way much earlier
than expected until it is made substantially strong and
tough.
• In continuous cutting, a similar tool will have a longer tool
life.

168
 7. Rigidity of Machine tool

• Both the machine tool and work should remain rigid

during the machining operation.

• If not, vibration will take place and then the cutting tool
will be subjected to intermittent loads and hence results
in shorter tool life.

169
 Tool life- Use of cutting fluids

• Cutting fluids are used in machining work for helping the

efficient performance of the tool operation.

• They assist in the operation in many ways, such as by

cooling tool and work, reducing friction, improving
surface finish, helping in breaking chips and washing
them away, etc

• These factors help in improving tool life, permitting

higher metal removal rate and improving quality of
surface finish.
170