Analysis and Design of

3D Steel Truss
Using SAP2000
ACECOMS, AIT

@Seismicisolation
@Seismicisolation
SAP2000 Tutorial Example ACECOMS, AIT

Analysis and Design of

3D Steel Truss
Using SAP2000
Table of Content
Objective ........................................................................................................................3

Problem ..........................................................................................................................3

Material ......................................................................................................................3

Geometry ....................................................................................................................3

Step-by-Step Solution.....................................................................................................4

Start Modeling and Define Grid Line.........................................................................4

Assign Frame Elements..............................................................................................6

Define and Assign Groups .........................................................................................8

Define and Assign Frame Section ............................................................................11

Assign Restraints......................................................................................................15

Define Load Cases....................................................................................................16

Assign Loads ............................................................................................................17

Analysis the Model...................................................................................................18

Design Steel Members..............................................................................................19

@Seismicisolation
@Seismicisolation
Analysis and Design of 3D Steel Truss 2/ 21
SAP2000 Tutorial Example ACECOMS, AIT

Objective
To demonstrate and practice step-by-step on the model-
ing, static analysis, design and optimization of 3D Trian-
gular Steel Truss using AISC-ASD89

Problem
Find the lightest steel pipe sections for primary and sec-
ondary members of 3D triangular truss as following de-
tails.

Material
Steel

Es = 29000 ksi
fy = 36 ksi
Poissons Ratio = 0.3

Geometry

15 @ 1.00m = 15.00

100
cm
4 x LL= 1,000 kg

cm
0
10

75 cm
Primary Members
Secondary Members

@Seismicisolation
@Seismicisolation
Analysis and Design of 3D Steel Truss 3/ 21
SAP2000 Tutorial Example ACECOMS, AIT

Step-by-Step Solution
Start Modeling and Define Grid Line

Step 1-1 Start Model: Start up screen of SAP2000, select the working unit “Kgf-cm”
from drop-down menu on the bottom-right of screen then click on or go to File >
New model.

Step 1-2 Define Grid Line: Define grid line only one bay of truss by entering grid
line parameters as shown in above figure and click “OK”.

@Seismicisolation
@Seismicisolation
Analysis and Design of 3D Steel Truss 4/ 21
SAP2000 Tutorial Example ACECOMS, AIT

Step 1-3: Back to main screen, showing gird line that has been defined from previ-
ous step. Close “X-Y Plane” window by clicking at top-right of screen.

@Seismicisolation
@Seismicisolation
Analysis and Design of 3D Steel Truss 5/ 21
SAP2000 Tutorial Example ACECOMS, AIT

Assign Frame Elements

Step 2-1 Draw Frame Elements in Bay 1: Click on to make cursor snap to grid
line or joint and click on or go to Draw > Draw Frame Elements then cursor will
be changed from selection mode to draw mode. Draw frame elements as shown in
above figure by single click at first end and double click on the other end one by
one.

@Seismicisolation
@Seismicisolation
Analysis and Design of 3D Steel Truss 6/ 21
SAP2000 Tutorial Example ACECOMS, AIT

Step 2-2 Select All Frame Elements: Change to selection mode by clicking on
. Click on to select all elements in model then selection status will report “6
Joints, 12 Frames selected”.

Step 2-3 Copy Elements in Bay 1 to Bay 2-15: Go to Edit > Replicate. Enter X =
“100” and Number = “14”. Click “OK”.

@Seismicisolation
@Seismicisolation
Analysis and Design of 3D Steel Truss 7/ 21
SAP2000 Tutorial Example ACECOMS, AIT

Back to main screen showing all frame elements in bay 1 are copied to all the rest
of bays.

Define and Assign Groups

Step 3-1 Select Primary Members: Click on to change from “3D” View to “XY
Plane @ Z=0” View. Draw selection rectangular cover all members in this plan (se-
lection status = “16 Joints, 15 Frames selected”)

@Seismicisolation
@Seismicisolation
Analysis and Design of 3D Steel Truss 8/ 21
SAP2000 Tutorial Example ACECOMS, AIT

Step 3-2 Select Primary Members: Click on to move XY Plane elevation from
Z = 0 to Z = 0.75. Draw 2 selection rectangular to cover all members along X-axis
as shown in above figure. (Selection status = “48 Joints, 45 Frames selected”.

Step 3-3 Define and Assign “PRIMARY” Group: Go to Assign > Group Name.
Enter “PRIMARY” in text box, click on “Add New Group Name” and click “OK”.

@Seismicisolation
@Seismicisolation
Analysis and Design of 3D Steel Truss 9/ 21
SAP2000 Tutorial Example ACECOMS, AIT

Step 3-4 Select Secondary Members: Click on to select all members. (Selec-
tion status = “48 Joints, 138 Frames selected”.

Step 3-5 Select Secondary Members: To deselect primary members, go to Select

> Deselect > Groups, select “PRIMARY” and click “OK”. (Selection status = “98
Frames selected”)

@Seismicisolation
@Seismicisolation
Analysis and Design of 3D Steel Truss 10/ 21
SAP2000 Tutorial Example ACECOMS, AIT

Define and Assign Frame Section

Step 4-1 Import Pipe Sections: Go to Define > Frame Sections. Select “Import
Pipe” from first drop-down menu.

Step 4-2 Import Pipe Sections: Select steel section database file (extension with
“.pro”). For this example select “Aisc.pro” and click “Open”.

@Seismicisolation
@Seismicisolation
Analysis and Design of 3D Steel Truss 11/ 21
SAP2000 Tutorial Example ACECOMS, AIT

Step 4-3 Import Pipe Sections: Select all pipe sections by clicking on first section
(“P.5”) and clicking on last section (“PXX8”) with holding Shift button in keyboard.
Click on “OK”.

Step 4-4 Import Pipe Sections: Click on “OK” again in “Pipe Section” window.
Back to “Define Frame Sections” dialogue showing all pipe sections are in “Frame
Sections list”.

@Seismicisolation
@Seismicisolation
Analysis and Design of 3D Steel Truss 12/ 21
SAP2000 Tutorial Example ACECOMS, AIT

Step 4-5 Define Auto Selection Section: Select “Add Auto Select” from second
drop-down menu.

Step 4-6 Define Auto Selection Section: Select all pipe sections in “List of Sec-
tions” by clicking on first section (“P.5”) and clicking on last section (“PXX8”) with
holding Shift button in keyboard. Click on “Add ->” to move all selected pipe sec-
tions from “List of Sections” list to “Auto Selections” list and click on “OK”.

@Seismicisolation
@Seismicisolation
Analysis and Design of 3D Steel Truss 13/ 21
SAP2000 Tutorial Example ACECOMS, AIT

Step 4-7 Assign Auto Selection Section: Click on to select all members.
Click on or go to Assign > Frame Sections, select “AUTO1” and click “OK”.
“AUTO1” sections are assigned into all members in model as shown in above fig-
ure. Click on to change back to normal mode.

@Seismicisolation
@Seismicisolation
Analysis and Design of 3D Steel Truss 14/ 21
SAP2000 Tutorial Example ACECOMS, AIT

Assign Restraints

Step 5-1 Assign Roller Support: Select 2 Joints at the first end as shown in above
figure by clicking on them one by one. Click on or go to Assign > Joint > Re-
straints, select and click “OK”.

@Seismicisolation
@Seismicisolation
Analysis and Design of 3D Steel Truss 15/ 21
SAP2000 Tutorial Example ACECOMS, AIT

Step 5-2 Assign Hinge Support: Select 2 Joints at the other end as shown in
above figure by clicking on them one by one. Click on or go to Assign > Joint >
Restraints, select and click “OK”.

Define Load Cases

Step 6-1 Modify Load Case: Enter Load = “DL” and clicking on “Change Load”

@Seismicisolation
@Seismicisolation
Analysis and Design of 3D Steel Truss 16/ 21
SAP2000 Tutorial Example ACECOMS, AIT

Step 6-2 Add New Load Case: Enter parameters as shown in above figure, click
“Add New Load” and click “OK”.

Assign Loads

Step 7-1 Select Joints: Click on 4 Joints at the middle of truss one by one.

@Seismicisolation
@Seismicisolation
Analysis and Design of 3D Steel Truss 17/ 21
SAP2000 Tutorial Example ACECOMS, AIT

Step 7-2 Add “LL” Load: Click on or go to Assign > Joint Static Loads >
Forces. Select Load Case Name = “LL”, enter Force Global Z = “-1000” (minus for
downward) and click “OK”.

Analysis the Model

Step 8-1: Click on to start analysis. SAP2000 will ask to save this model. Se-
lect folder and specify File name to save this model. Click on “Save”.

@Seismicisolation
@Seismicisolation
Analysis and Design of 3D Steel Truss 18/ 21
SAP2000 Tutorial Example ACECOMS, AIT

Step 8-2 Start Analysis: Click on or go to Analyze > Run. Check error mes-
sages from "Analysis" window after analysis is complete.

Design Steel Members

Step 9-1 Select Design Code: Go to Options > Preferences, select “Steel” tab,
select Steel Design Code = “AISC-ASD89” and click "OK"

@Seismicisolation
@Seismicisolation
Analysis and Design of 3D Steel Truss 19/ 21
SAP2000 Tutorial Example ACECOMS, AIT

Step 9-2 Select Design Groups: Go to Design > Select Design Group, double
click on “PRIMARY” and “SECONDARY” one by one to move these groups from
“List of Groups” to “Design Groups”.

Step 9-3 Select Design Combo: Go to Design > Select Design Combo,
SAP2000 will create load combinations according selected code from previous step
and add them into Design Combos automatically. Select one of them and click
“Show” to view defined load case and load factors. Load combination can be de-
fined manually from Define > Load Combinations. Click “OK” to accept this de-
fault.

@Seismicisolation
@Seismicisolation
Analysis and Design of 3D Steel Truss 20/ 21
SAP2000 Tutorial Example ACECOMS, AIT

Step 9-4 Start Design: Go to Design > Start Design/Check of Structure.

SAP2000 will optimize by selecting the lightest section (W8x18 for this example)
from the section group (“AUTO1”) which satisfies the AISC-ASD89 that can be
shown by clicking and selecting “Section” in “Frames”.

Click on and draw rectangular line cover the first end area to enlarge “3-D”
view. In “3D” View shows SAP2000 will assign “P3” section to all primary members
and “P1.25” to all secondary members.

@Seismicisolation
@Seismicisolation
Analysis and Design of 3D Steel Truss 21/ 21