Scribd
Upload
47 views

Engineering Drawing

This document provides instructions and questions for a mechanical engineering drawing exam. It includes 6 questions testing skills in completing projections, drawing conventional representations, assemblies, and objects penetrating each other. Students are instructed to show construction lines, assume necessary data, and use specific grades of pencils. Dimensions are to be in millimeters and all questions are compulsory.

Uploaded by

rsinha.0604
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
47 views

Engineering Drawing

This document provides instructions and questions for a mechanical engineering drawing exam. It includes 6 questions testing skills in completing projections, drawing conventional representations, assemblies, and objects penetrating each other. Students are instructed to show construction lines, assume necessary data, and use specific grades of pencils. Dimensions are to be in millimeters and all questions are compulsory.

Uploaded by

rsinha.0604
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

(IMT) INSTITUTE OF MANAGEMENT AND TECHNOLOGY

Mechanical Engineering Drawing

Instruction:
1) All questions are compulsory.
2) Use only H / 2H grade pencils.
3) Retain all construction lines and nomenclature.
4) Assume suitable data if necessary.
5) All dimensions in mm.

Q.1] Attempt the following.


a) Figure. -I shows Front View and partial Auxiliary View of an object. Complete Top View.

(OR)
a) Figure –II shows Front View and Top View. Complete the partial Auxiliary View of
given object.

b) Line AB 80 mm long has it’s end A in the H.P. and 20 mm in front of the V.P. Draw it’s
projection when line AB makes an angle of 45° with the H.P. and 35° with the V.P.

(OR)

b) A hexagonal plane 25 mm sides is having one of it’s corners on the H.P. with it’s surface
inclined at 450 to the H.P. and diagonal through the corner on H.P is parallel to the V.P.
Draw it’s projections.

Q.2] Attempt any ONE of the following


a) A vertical cone of 80 mm diameter and 100 mm long is penetrated by a horizontal cylinder.
The axis of cylinder is parallel to both the reference planes and is 5 mm away from the
axis of cone. The cylinder axis is 30 mm above the base of cone and diameter of cylinder is
40 mm. Draw the projections showing curves of intersection.

b) A square prism of 45 mm side stands vertically with its rectangular faces equally inclined to
VP. It is penetrated by a horizontal triangular prism of 35-mm side of base such that their
axes bisect each other at right angles. Draw the projection showing lines of intersection,
when the rectangular face of triangular prism is parallel to VP and is away from the observer.

Q.3] Attempt the following

a) Draw the conventional representation of


i) Antifriction Bearings ii) Splined Shaft
iii) Spring with flat end iv) Half Section
(OR)
b) 1) Calculate upper limit size and lower limit size for 25 H7.
2) Prepare a welding drawing of two shafts of equal diameter welded end to end by a square
butt joint with convex contour at site.

Q.4] Attempt any ONE of the following.


a) Draw the assembly of the details shown in Figure-I

(OR)
a) Draw the details of the assembly drawing shown in Figure-II
Q.5] Attempt any TWO of the following
a) A hole of 50mm diameters is drilled through a vertical cylinder of 60 mm diameter and 80
mm long. The axis of hole being parallel to both the ref. planes and 10 mm away from the
axis of vertical cylinder . Draw projections showing curves of intersection.

b) A vertical square prism base 50mm side and height 100mm has a face inclined at 300 to
V.P It is completely penetrated by another horizontal square prism base as 35 mm side
and 100mm long, faces of which are equal inclined to V. P. The axis of both the prism is
parallel to V.P and bisects each other of right angles .Draw Projections showing lines of
intersection.

c) A vertical cone 80 mm dia of base and axis 100mm long is completely penetrated by a
horizontal cylinder of 50mm dia. The axis of cylinder is parallel to both the ref. planes
and intersects the axis of cone at 30 mm above the base of cone. Draw the projections
showing curve of intersection. Length of cylinder is 100mm

Q.6) A straight line AB 70 mm long has it’s end A 10 mm. above the H.P. and end B 50 mm in
front of the V.P. Draw the projections of line AB if it is inclined at 300 to the H.P and
450 to the V.P.
(OR)
Q.7) A thin circular plate of 50mm diameter is resting on point A of it’s rim with the surface of
the plate inclined at 450 to the H.P and the diameter through A inclined at 300 to the V.P. Draw
the projection of the plate when it’s centre is 40mm above the H.P. and 40 mm in front of the
V.P.

You might also like