Module 16: Troubleshoot Static

and Default Routes

Instructor Materials

Switching, Routing and Wireless Essentials v7.0

(SRWE)
Module 16: Troubleshoot
Static and Default Routes
Switching, Routing and Wireless
Essentials v7.0 (SRWE)
Module Objectives
Module Title: Troubleshoot Static and Default Routes

Module Objective: Troubleshoot static and default route configurations.

Topic Title Topic Objective
Packet Processing with Static Routes Explain how a router processes packets when a static route
is configured.

Troubleshoot IPv4 Static and Default Route Troubleshoot common static and default route configuration
Configuration issues.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 9
16.1 Packet Processing with
Static Routes

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 10
Packet Processing with Static Routes
Static Routes and Packet Forwarding
• PC1 addresses a packet to PC3 and sends it to the
default gateway address.
• When the packet arrives on the R1 G0/0/0 interface,
R1 decapsulates the packet and searches the routing
table for a matching destination network entry.

If the destination IP address:

• Matches a static route entry, R1 will use the static route to identify the next-hop IP address or exit
interface.
• Does not match a specific route to the destination network, then R1 will use the default static route
(if configured).
• Does not match a route table entry, then R1 will drop the packet and send an ICMP message back
to the source (i.e., PC1).

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 11
Packet Processing with Static Routes
Static Routes and Packet Forwarding (Cont.)
Assuming R1 matched a routing table entry, it
encapsulates the packet in a new frame and
forwards it out of interface S0/1/0 to R2.
• R2 receives the packet on its S0/1/0 interface.
• It decapsulates and processes the packet the
same way R1 did.
• When R2 finds a match in the routing table, it uses
the identified next-hop IP address or exit interface
and sends the packet out of its interface S0/1/1
towards R3.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 12
Packet Processing with Static Routes
Static Routes and Packet Forwarding (Cont.)
• R3 receives the packet, decapsulates it, and
searches the routing table for a match.
• The destination IP address of PC3 matches the
directly connected G0/0/0 interface. Therefore, R3
searches the ARP table for the Layer 2 MAC
address of PC3.
• If no ARP entry exists, then R3 sends an ARP
request out of the G0/0/0 interface.

• PC3 responds with an ARP reply containing its MAC address.

• R3 encapsulates the packet in a new frame and uses the PC3 MAC address as the
destination MAC address and the G0/0/0 MAC address as the source MAC address.
• The frame is forwarded out of interface G0/0/0 and PC3 receives and processes it
accordingly.
© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 13
16.2 Troubleshoot IPv4 Static
and Default Route
Configuration

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 14
Troubleshoot IPv4 Static and Default Route Configuration
Network Changes
Networks fail for a number of reasons:
• An interface can fail
• A service provider drops a connection
• Links can become oversaturated
• An administrator may enter a wrong configuration.

Network administrators are responsible for pinpointing and solving the problem.

To efficiently find and solve these issues, it is advantageous to be intimately familiar with
tools to help isolate routing problems quickly.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 15
Troubleshoot IPv4 Static and Default Route Configuration
Common Troubleshooting Commands
Command Description
ping • Verify Layer 3 connectivity to destination.
• Extended pings provide additional options.

traceroute • Verify path to destination network.

• It uses ICMP echo reply messages to determine the hops to
the destination.
show ip route • Displays the routing table.
• Used to verify route entries for destination IP addresses.
show ip interface brief • Displays the status of device interfaces.
• Used to verify the operational status and IP address of an
interface.
show cdp neighbors • Displays a list of directly connected Cisco devices.
• Also used to validate Layer 1 and 2 connectivity.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 16
Troubleshoot IPv4 Static and Default Route Configuration
Solve a Connectivity Problem
Connectivity from PC1 to PC3 fails.
• Extended pings from the R1 G0/0/0 interface to PC3 fail.
• Pings from R1 (i.e., S0/1/0 interface) to R2 are
successful.
• Pings from R1 (i.e., S0/1/0 interface) to R3 are
successful.

R2# show ip route | begin Gateway

• R2 routing table reveals the problem Gateway of last resort is not set
172.16.0.0/16 is variably subnetted, 5 subnets, 2 masks
and the incorrect static route is C 172.16.1.0/24 is directly connected, GigabitEthernet0/0/0
removed. L
C
172.16.1.1/32 is directly connected, GigabitEthernet0/0/0
172.16.2.0/24 is directly connected, Serial0/l/0
• A new static route solves the problem. L
S
172.16.2.2/32 is directly connected, Serial0/l/0
172.16.3.0/24 [1/0] via 192.168.1.1
• ip route 172.16.3.0 255.255.255.0 172.16.2.1 192.168.1.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.1.0/24 is directly connected, Serial0/1/1
L 192.168.1.2/32 is directly connected, Serial0/1/1
S 192.168.2.0/24 [1/0] via 192.168.1.1
R2#

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 17
16.3 Module Practice and Quiz

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 18
Structured Design
Packet Tracer – Troubleshoot Static and Default Routes
In this activity you will troubleshoot and static and default routes and repair any errors that
you find.
• Troubleshoot IPv4 static routes.
• Troubleshoot IPv6 static routes.
• Configure IPv4 static routes.
• Configure IPv4 default routes.
• Configure IPv6 static routes.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 19
Structured Design
Lab - Troubleshoot Static and Default Routes
In this lab, you will complete the following objectives:
• Evaluate Network Operation.
• Gather information, create an action plan, and implement corrections.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 20
Module Practice and Quiz
What did I learn in this module?
• A host sends a packet to another host and sends it to the default gateway address.
• When the packet arrives on a router interface, it decapsulates the packet and searches the
routing table for a matching destination network entry.
• If the destination IP address:
• Matches a static route entry, the router will use the static route to identify the next hop IP address or exit
interface.
• Does not match a specific route to the destination network, then the router will use the default static
route (if configured).
• Does not match a route table entry, then the router will drop the packet and send an ICMP message
back to the source.
• If the router matched a routing table entry, then the router encapsulates the packet and
forwards it out of the appropriate interface.
• The packet is forwarded from router to router until it reaches its destination network.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 21
Module Practice and Quiz
What did I learn in this module? (Cont.)
• When the packet reaches the destination network, that router will search the routing table for
a match.
• When the destination IP address matches a directly connected Ethernet interface, the router
searches the ARP table for the Layer 2 MAC address of the destination IP address.
• If no ARP entry exists, the router sends an ARP request out of the Ethernet interface
• The destination host responds with an ARP reply containing its MAC address.
• The router then encapsulates the packet in a new frame. It uses the MAC address of the
destination host as the frame destination MAC address, and the MAC address of the router
Ethernet interface as the source MAC address in the frame.
• The frame is forwarded out of the appropriate interface.
• The packet arrives on the network interface card (NIC) interface of destination host and is
processed accordingly.

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 22
Module Practice and Quiz
What did I learn in this module? (Cont.)
Common IOS troubleshooting commands to troubleshoot IPv4 Static and default routes
include:
• ping
• traceroute
• show ip route
• show ip interface brief
• show cdp neighbors detail

© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential 23