Boq 622014

Validate Print Help Percentage BoQ
Tender Inviting Authority: DIRECTOR SWACH PROJECT UDAIPUR

Name of Work: CONSTRUCTION OF NEW MULTIPURPOSE GIRLS HOSTEL AT MANPUR DISTRICT SIROHI CAPACITY 100
Contract No: 12/2023-24_9
Name of
the Bidder/
Bidding
Firm /
Company :
PRICE SCHEDULE
(This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is
NUMBER # TEXT # Bidder Name and
NUMBER # ValuesTEXTonly
# )
Sl. Item Description Quantity Units

No.
1 2 4 5
1 Surface dressing of the ground including removing vegetation and inequalities not exceeding 15cm deep
and disposal of rubbish lead up to 50 Mtr. And lift up to 1.5 Mtr.
1086.93 Sqm
2 Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation
trenches or drains (not exceeding 1.5 m in width or 10 sum on plan) including dressing of sides and
ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of
jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50
meter.
All kinds of soils
1596.48 Cum
3 Providing and laying in position cement concrete including curing, compaction etc. complete in specified
grade excluding the cost of centering and shuttering - All work up to plinth level. 1:4:8 (1 cement : 4
coarse sand : 8 graded stone aggregate 40 mm nominal size).
272.20 Cum
4 Filling available excavated earth (excluding rock) in trenches plinth side of foundation etc. in layers not
exceeding 20 cm in depth consolidation each deposited layer by ramming and watering including lead up
to 50 mtr and with all lift.
1420.85 Cum
5 Providing and laying in position specified grade of cement concrete for all RCC structural elements upto
plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3
coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of
centering, shuttering and reinforcement.
M25 grade Design Mix
348.94 Cum
6 Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/Lindane
emulsifiable concentrate of 20%
250.00 Ltr
7 Diluting and injection Chloropyrifos Emulsifiable concentrate 20% with 1% concentration for PRE-
CONSTRUCTIONAL Anti termite treatment as per IS 6313 part III as amended from time to time and
creating a continuous chemical barrier under and around the column pits, wall trenches, basement
excavation, top surface of plinth filling, junction of wall and floor along the external perimeter of building
expansion joints, over the top surface of consolidated earth of which aproch is to be laid surrounding of
pipes and conduits etc. complete as per specification (Plinth floor area only shall be measured for
payment and excluding the cost of chemical emulsion) .
1093.01 Sqm
8 Providing and laying in position specified grade of cement concrete for RCC structural elements upto
floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1
cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost
of centering, shuttering and reinforcement for Walls (any thickness) including attached pilasters,
buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.
108.60 Cum.
cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost
of centering, shuttering and reinforcement for Beams, suspended floors, roofs, griders having slopes up
to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral
staircases etc.
472.19 Cum.
10 Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways
and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc.
1165.88 Sqm
11 Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with
steel props and removal of formwork for upto floor five level for :
Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,
anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc.
3453.47 Sqm
12 --Do-- Columns, pillars, posts and struts etc.
1444.02 Sqm
13 Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing
in position and binding (including cost of binding wire) all complete up to floor three level. Thermo-
mechanically Treated bars (Conforming of relevent IS code) Qtty @ 111 Kg/Cum
103530.67 Kg
14 Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar
above 30 CM thick wall in:
Cement Mortar 1:6 ( 1-Cement : 6-Sand).
818.14 Cum
15 Random rubble dry stone Kharanja under floor.
274.24 Cum
16 Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level
in all shapes and sizes in :
Cement mortar 1 : 6 (1 cement : 6 coarse sand)
486.39 Cum
17 Half brick masonry in Superstructure , above plinth level upto floor V level using bricks of designation 75
Cement mortar 1 : 4 (1 cement : 4 coarse sand)
1061.43 Sqm.
18 Add extra providing and placing in position 2 Nos. ,6mm Ø M.S. bar at every third course of half brick
masonry.
1045.82 Sqm.
19 Supplying and fixing in walls machine cut and polished stone shelves, tands and in CM 1:3 with machine
cut edges : Sand or other approved stone 50mm thick.
16.86 Sqm
20 Supplying and fixing in walls machine cut and polished stone shelves, tands and in CM 1:3 with machine
cut edges : Kota stone 25 to 30mm thick.
516.40 Sqm
21 Extra over item for machine cut both side polished stone is used.
384.33 Sqm
22 Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps,
Shelves, Sills Counters, Floors etc. 15-18 mm thick laid on 12mm (Av.) thick base of cement mortar 1:3 (1
cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with
pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. South
(Red) Above 3601 Cm2 Slabs
86.01 sqm
23 Providing and fixing Marble stone flooring table rubbed, 15- 18 mm thick over 20mm (Av.) thick base of
CM 1:4 (1 cement : 4 coarse sand) jointing with white cement mortar 1:2 (1 white cement : 2 marble dust)
with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete.
OR
Providing and fixing stone slabs table rubbed, 15-18 mm thick in Walls, Steps, Pillars, Counters, Jambs,
Shelves, Sills etc. laid on 12mm (Av.) thick base of CM 1:3 (1 cement : 3 coarse sand) jointing with white
cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab
including grinding, rubbing and polishing complete.
Rajnagar 1st quality/Ageria with light spots.
Above 3601 Cm2 Slabs
123.79 sqm
24 Extra for providing edge moulding to 15-18mm thick marble/ Granite/Kota stone counters, Vanities etc.
including machine polishing to edge to give high gloss finish etc. complete as per design approved by
Engineer-in-Charge. Marble Work Half Edge moulding
94.18 Rmt
25 Granite/Kota Stone Work
Half Edge moulding
199.90 Rmt
26 Making linning/ groove 3mm to 5mm in granite/marbal step.
500.00 Mtr.
27 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified
by the manufacture ) of approved make in all colours, shades except burgundy, bottle green, black of any
size as approved by Engineer in charge in skiriting, risers of steps and dados over 12 mm thick bed of
cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm
including pointing in white mixed with pigment of matching shade complete.
616.00 Sqm
28 Finishing with neat white cement (punning). Qty as per item 25
701.56 Sqm
29 Providing and laying Ceramic MAT floor tiles (thickness to be specified by the manufacturer) of 1st quality
conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown of any
size, laid on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) including pointing in white
cement mixed with pigment of matching shade complete.
185.31 Sqm
30 P & F 1st qualityVitrified Porcelain Polished tiles on floor, skirting and steps etc.in different sizes (thickness
to be specified by manufactuer) with water absortion less than 0.08% and conforming to IS 15622 of
approved make in all colour and shade, laid with 20 mm thick CM 1 : 4 including grounting the joints with
white cement and matching pigment etc complete. size 600 mm X 600 mm
93.90 Sqm.
31 Providing & fixing door, window, chowkhats and other frames, including antitermite treatment, M.S. flat,
hold fasts of size 250 x 40 x 3mm fixed with M.S. bolt 5mm dia 50mm long duly embedded in cement
concrete M-15 grade : Sal wood Grade - I.
0.34 Cum.
32 Providing and fixing fully panelled/partly panelled/ double leaf shutter frame for doors as per approved
design and drawings with approved ordinary C.P./ oxidised steel fittings as per Annexure - 'A' and width of
styles & top rails of 100mm and lock rails width of 150mm and bottom rails of 200mm width including
teak wood beading of size 19mm x 12mm on both faces complete : 35 mm thick Nigeria wood grade I
4.46 Sqm.
33 Providing and fixing fully panelled /partly panelled double leaf shutters frame for windows and
ventilators as per approved design and drawings with approved steel fittings as per Annexure ‘A’ and
width of styles, bottom and top rails 75mm including intermediate rails 50mm wide, beading of 25mm x
15mm size on both faces : 30 mm thick Nigeria wood grade I
2.30 Sqm.
34 Providing and fixing wood panelling or panelling and glazing in panelled or panelled and glazed shutters
for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside
grooves or rebates to be measured). Panelling for panelled and glazed shutter 25 mm to 40 mm thick
Nigeria wood Grade I
2.94 Sqm.
35 5 mm float glass
2.55 Sqm.
36 Extra for providing other type of fittings as mention in annexure A ( as approved by EI) : Brass fittings
7.40 Sqm.
37 Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked
using Phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure
'A' : 35 mm thick. Commercial Veneer both side
142.41 Sqm.
38 Extra for providing external lipping with 2nd class teak wood battens 6 mm minimum depth on all edges
of shutters (over all area of door shutter to be measured) Over item no. 8.13.
150.55 Sqm
39 Steel work in built up tubular trusses including cutting, hoisting ( height upto 10 m)fixing in position and
applying a priming coat of approved steel primer, welded and bolted including special shaped washers
etc. complete. Hot finished welded type tubes.
1000.00 Kg.
40 Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints
mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of
1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs
and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of
necessary butt hinges and screws and applying a priming coat of approved steel primer.
4319.00 Kg
41 Providing and fixing in position collapsible steel shutters with vertical M.S. Channels 20 x 10 x 2mm and
bracket with flat iron diagonals 20 x 5mm. size with top and bottom rail of T-iron 40 x 40 x 6mm. with
40mm dia steel pulleys/ball bearing complete with bolts, nuts locking arrangements inside and outside
stoppers, handles etc. as per specification including applying a priming coat of approved steel primer. (To
be measured and paid as per outer dimension).
18.95 Sqm
42 Providing and fixing stainless steel railing made of Hollow tubes, channels, plates etc., including welding,
grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary
stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel
dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab
with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of
stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners
etc.). Grade 304
300.00 Kg
43 Providing and fixing M.S. sheet 1mm thick single leaf door shutter in angle iron frame 35x35x5mm
suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading
extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including
two coats of anit-corrosive red oxide primer paint
69.26 Sqm
44 Providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section
joints mitred and welded with steel lugs 13x3mm, 10cm. long embedded in cement concrete block
15x10x10cm. of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with
wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required
including providing and fixing of plain glass panes 4mm thick with cooper glazing clips and special metal
sash putty of approved make or metal beading with screws complete including priming coat of approval
steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel
handles peg stay etc. as required : Partly fixed and partly openable [ fixed area not to exceed 33%]
180.60 Sqm.
45 Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal
beading 20x3mm with suitable screw at not exceeding 150mm distance. Qtty. As per item no. 42
187.10 Sqm.
46 Providing and fixing Square bars or other flat welded to window, ventilatiors etc. 10mm Bar 0.78 Kg/Rmt.
1139.51 Kg
47 Providing and fixing of double leaf steel shutter for cupboard, the Sqm frame is made of pressed steel ISI
section 80x25 mmx 1.25 mm thick with 1.00 mm MS sheet to spot welded including holdfasts of 15x3mm,
MS oxidized fittings such as butt hinges, sliding doors bolts, handles, tower bolts and twin peg etc
complete including applying priming coat of approved steel primer of red oxide zinc chromate and spray
painting in approved shade with deco paint of approved quality complete as per direction of Engineer In
Charge
256.32 Sqm
48 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm
and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard
design :
299.85 Rmt
49 Painting top of roofs with bitumen of approved quality at 17kg per 10 sum impregnated with a coat of
coarse sand at 60 cudm per 10sqm including cleaning the slab surface with brushes and finally with a
piece of cloth lightly soaked in kerosene oil complete:
With residual type petroleum bitumen of penetration 80/100
1069.20 Sqm
50 Providing and laying brick kharanja on roofs with cement mortar 1:4 (1 cement : 4 coarse sand) mixed
with 2% integral water proofing compound in square pattern 75mm to 100mm thick average
1157.64 Sqm
51 Filling of sunk portion of roof with earthen pots of required height including filling voids with 1:3:6 light
concrete, using brick bats complete levelling and dressing the surface by 50mm thick cement concrete
1:2:4 as per specification.
40.41 Cum
52 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying
cement slurry mixed with water proofing cement compound consisting of applying :
a) first layer of slurry of cement @ 0.488 kg/sqm mixed with water proffing cement compound @0.253
kg//sqm .This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242
kg/sqm mixed with water proffing cement compound @ 0.126 kg/sqm This layer will be allowed to air
cure for 4 hours followed by water curing for 48 hours.
The rates includes preparation of surface treatment & sealing of all joints ,corners, junction with polymer
mixed slurry.
107.76 Sqm
53 Providing & laying broken glazed titles on roof ( broken glazed tiles not less than 9 Kg/Sqm) on top of hot
bitumen @ 1.7 Kg/Sqm. (1.40 Kg of VG-40 (30/40 )grade and 0.30 Kg/Sqm. Of VG-10 (80/100) grade) and
joints filled with cement mortar 1 :2 (1 cement:2 marble dust mixed with water proofing compund all
complete as per direction of Engineer-in-charge. Qtty. As per item no. 46
1157.64 Sqm
54 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L
hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers
filled with white lead and including a coat of approved steel primer and two coats of approved paint on
overlapping of sheets complete (upto any pitch in horizontal/ vertical or curved surfaces) excluding the
cost of purlins, rafters and trusses and including cutting to size and shape whenever required. 0.63 mm
thick with zinc coating not less than 275 gm/m2
74.32 sqm.
55 Kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey
cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing
complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) For area of each slab from 2001 to
5000 Sq.Cm
1446.64 Sqm
56 Rough Chisel dressed Kota stone 35 mm thick flooring of approved shade set in pattern over 20mm thick
base of cement mortar 1:6 (1 cement : 6 coarse sand) and pointing with cement sand mortar 1:3 with
pigment to match the shade of stone with joint thickness up to 15 mm complete in all respects :
184.22 Sqm
57 Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement
slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20
mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) Dark shade using ordinary cement.
55.74 Sqm
58 Plaster on new surface on wall in cement sand mortar 1:4 including raking of joints etc. complete fine
finish:
20mm thick
5469.47 Sqm.
59 Plaster on new surface on wall in cement sand mortar 1:4 including raking of joints etc. complete fine
finish:
25mm thick
3058.59 Sqm.
60 6 mm cement plaster to ceiling of mix 1:3 (1 cement : 3 fine sand)
1857.59 Sqm
61 Extra for lining out plaster to imitate stone or concrete blocks
walling
250.00 Sqm
62 Making of Drip course (Tapaka) in cement sand mortar 1:6 width upto 40 mm and 10 mm thick as per
approved design
200.00 Mtr
63 Making grooves as per design in plaster 10mm to 20mm wide
800.00 Rmt
64 Providing and applying white cement based putty over plastered surface to prepare the surface even and
smooth complete.
New Plastered Surface (three or more coats)
7327.05 Sqm.
65 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade
including all scaffolding: Two or more coats on new work including prepartion of base
with primer, putty, lippy etc complete in all respect.
7327.05 Sqm
66 Painting exterior surface of Wall with 100% acrylic exterior paint of approved brand and manufacture to
give an even shade with two or more coats including prepartion of base with sand papering, primer,
putty, etc complete in all respect including scaffolding and safety provision
2829.29 Sqm
67 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :
Two or more coats on new work
1191.64 sqm
68 French sprit polishing:
Two or more coats on new work including a coat of wood filler.
15.61 Sqm
69 Providing and Fixing Chiken wire mesh at the joint of masonry members/ R.C.C. Members with Nails
complete in all respect.
70.00 Sqm
70 Renewing glass panes, with putty and nails wherever necessary: Float glass panes of thickness 4 mm
19.56 Sqm.
71 Rebarring work in old R.C.C structures including making bore hole to adjust required bar diameter and
filling a good quality filler to provide a tensil strength as per requirement and fix the Bar to the saction
including cost of bars.
10.00 Each
72 16 mm bar
8.00 Each
73 20 mm bar
8.00 Each
74 Providing and fixing expansion joint board for building RCC column beams, walls, slab of Polyethylene
foam of density 30 to 35 Kg/m3 of Armour Board. 25 mm Thick
63.13 Sqm
75 Supplying and providing of two components poly sulphide sealant containing solid contents, confirming to
standard specification and approved compatible primer, for priming vertical faces prior to application of
poly sulphide sealant including all labour charges for sealing of expansion joints after drill mixing of two
components sealing compound. Cleaning and preparation of expansion joint using wire brush sand
papering with emery paper and filing with suitable mechanical means. The work includes racking and
cleaning of joints, sticking, debonding tape on bottom of joint, applying primer on edges, using masking
tape on edges, providing of sealant and removal of masking tape immediately after providing sealant in
joint. To vertical joint between RCC columns, bricks & stone masonry in size 40 mm width and 12 mm
depth, including providing back up material (Thermocol foam) if required.
35.00 Mtr
76 To joints in flooring, as per drawing with first layer of poly sulphide sealant in size 20 mm width and 10
mm depth over PE Foam and then providing polyethylene foam back up rod 25 mm dia size and finally
providing another layer of poly sulphide sealant in size 20 mm width and 10 mm depth over P.E. back up
rod as per application procedure and direction of Engineer-in-charge.
35.00 Mtr
77 Providing and fixing 150 mm wide sheet covering over expansion joints with iron screws as per design to
match the colour / shade of wall treatment. Aluminum fluted strips 2 mm thick
31.70 Mtr
78 Providing and laying damp-proof course with cement concrete grade M-150 (1 : 2 : 4) mortar prepared
with 1% solution of water-proof compound complete as per specification . 50mm thick.
42.41 Sqm
79 P & F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm
vitreous china P or S trap including cutting and making good the wall and floor: Size 580x440 mm
21.00 Each
80 P & F European type white glazed vitreous china 1st quality W.C pan (IS : 2556 Mark) with P or S trap
including cutting and making good the wall and floor
5.00 Pair
81 P & F water closet Seat Covers with brass hinges complete :
Solid PVC (IS 2548 marked) grade-I Black for EWC.
5.00 Each
82 P & F Low level Flushing Cistern of 10 litres capacity (IS : 2556 mark) of approved make with complete
fittings C.I. brackets duly painted, brass ball cock with ball (IS: 1703 mark) complete including cutting and
making good the wall:
PVC with PVC bend as per IS : 7231.
5.00 Each
83 P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No.
15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, P.V.C Waste
pipe with PVC nut 32 mm complete including cutting & making good the wall :
Size 580 mm x 450 mm
26.00 Each
84 KITCHEN & LAB. SINKS:
P & F Kitchen & Lab. Sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling,
C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up-to floor level complete including cutting and
making good the wall & floor :
1.0 mm thick stainless steel AISI -304 & IS 13983-1994 kitchen sink of approved make as per Engineer-in-
charge with large waste coupling.
Overall size (inches) = 24 x 18 x 8, Bowl size(inches) = 20x16x8
3.00 Each
85 P & F Bevelled edge Mirror/mirror with teak wood lipping around of special glass of approved make as
per direction of Engineer-in-charge complete with 6mm thick commercial ply base fixed to wooden
screws & washers.
Size 600 x 450mm x 4 mm thick
26.00 each
86 P & F Grating of approved quality/make: Stainless Steel Sheet size 125mm dia.
83.00 Each
87 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal
stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe
with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent
cement and the cost of cutting chases and making good the same including testing of joints complete as
per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls
etc.,)
15 mm dia nominal bore B class
100.00 Mtr.
88 25 mm dia nominal bore B class
100.00 Mtr.
100.00 Mtr.
90 20mm nominal size
10.00 Mtr.
stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included
jointing of pipes & fittings with one step CPVC solvent cement , trenching refilling & testing of joints
complete as per direction of Engineer in Charge. (External work).
15 mm dia nominal bore B class
100.00 Mtr.
92 20mm nominal size
10.00 Mtr.
112.00 Mtr.
100.00 Mtr.
150.00 Mtr.
96 S&F G.I/. Union ISI Marked In G.I. Pipe line as required complete in all respect of size.
15 mm dia nominal bore
12.00 Each
97 25 mm dia nominal bore
12.00 Each
10.00 Each
8.00 Each
100 P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: C.P. Brass bib cock,15mm nominal
bore.
53.00 Each
101 C.P. Brass bib cock Long body, 15mm nominal bore weight not less than 690 gm
30.00 Each
102 P & F Stop Cock (IS :8931 Mark), superior quality & of approved make: C.P. Brass 15mm nominal bore.
22.00 Each
103 C.P. Brass Concealed Stop Cock 15mm.
20.00 Each
104 P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. C.P.
Inlet connection 15mm.Brass (IS : 8931 marked) with 37 cm long pipe and nut.
40.00 Each
105 P & F Flush Cock / Flush Valve (IS : 9758 Mark) for WC of approved quality make : CP brass Concealed
25mm nominal bore.
26.00 Each
106 P & F Full way valve (IS : 778 mark or wheel valve of approved make
Gun-metal 15 mm dia nominal bore
20.00 Each
107 (-do-) 20mm nominal bore.
1.00 Each
108 Gun-metal 25 mm dia nominal bore
21.00 Each
5.00 Each
5.00 Each
111 P & F ball cock (IS: 1703 Mark) with rod & pvc ball complete make 750 gm 15mm nominal size
17.00 Each
112 P & F PVC Storage Tank ISI Marked (IS : 12701) indicating the BIS license No), of approved make with
cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including
making connection etc., complete of approved design:
1000 litres capacity.
14.00 Each
113 750 litres capacity.
2.00 Each
114 500 (-do-)
1.00 Each
115 Providing & Laying C.C. 1:5:10 (Stone aggregate 40mm nominal size) upto haunches of S.W. pipes
including 150 mm thick bed concrete (Width W= Dia of pipe in Cm+ 30Cm.) concrete width to be reduced
from width W at center of pipe to `0` at top of pipe. (Excluding cost of pipe)
150 mm dia S.W. pipe
around 160mm rigid PVC pipe
75.00 Mtr.
116 Providing, Laying & Jointing R.C.C. class NP-2 Non-Pressure pipes (IS : 458mark) of approved make with
collars, jointed with C.M. 1:2 or having Spigot and socket ends with flexible rubber rings joint including
testing of joints etc. complete :
50.00 Mtr.
117 P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with
solvent cement rubber ring and lubricant:
Coppler
110 mm dia
80.00 Each
118 75 mm
50.00 Each
119 Plain Tee 110 mm dia
60.00 Each
120 75 mm
50.00 Each
121 Door Y 110 mm dia
40.00 Each
122 75 mm
30.00 Each
123 Bend 87.5
110 mm dia
70.00 Each
124 75 mm
35.00 Each
125 110 mm dia
95.00 Each
126 Pipe Clip 110 mm dia
300.00 Each
127 75 mm
75.00 Each
128 P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2 .) approved quality /make including joining the pipe
with solvent cement rubber ring and lubricant.
75 mm dia
105.00 mtr.
129 110 mm dia
450.00 mtr.
130 110 mm dia
15.00 Mtr.
131 160 mm dia
100.00 mtr.
132 P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with
solvent cement rubber ring and lubricant:
Coupler (socket)
110mm dia
2.00 Each
133 Plain Tee 75mm dia
1.00 Each
134 110mm dia
1.00 Each
135 Bend 87 .5
75mm dia
1.00 Each
136 110mm dia
3.00 Each
137 Plain floor trap 110mm dia
2.00 Each
138 Pipe Clip 110mm dia
5.00 Each
139 Construction of manhole in all type of soil inner size 90 X 60 Cm. 300 mm thick masonry in CM 1:6, 10 Cm.
thick cement concrete 1:5 10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating
neat cement, 50mm thick M-15 grade C.C. flooring, making channels, 80mm thick stone slab covering
with 40mm thick M-15 grade C.C. flooring, Cement cover with frame of 450mm dia, earthwork etc.
complete as per design including disposal of surplus earth within 50 mtr. lead. Depth
up to 0.5 M
15.00 Each
140 Construction of soakage well in all type of soil with 300 mm thick dry masonry, top and bottom 300 mm
course in CM 1:6, 80mm thick stone slab, jointing of slab in CM 1 : 3, Ralthal, Kharanja, 40 mm thick M-15
grade C.C flooring , earthwork complete as per approved drawing including disposal of earth within a lead
of 50 mtr.:
Size 300 Cm. dia outside & 240 Cm. depth.
2.00 Each
141 Making of hole (width up to 150 mm) in R.C.C. slab/wall/beams by power driven drilling machine
complete as per direction of EI Upto 150mm thick.
30.00 Each
142 Construction of septic Tank in all types of soil with 40 Cm .thick masonry in CM 1:6, 15 Cm thick C.C bed of
1:5:10, M-15 grade C.C floor & RCC slab covering with M15 grade c.c. floor, 50 mm thick stone slab
partition walls, 20 mm thick plaster in CM 1:6 finished with neat floating cement, 4 Nos stone foot rests of
approved design ,two No. 450 mm dia each Ferro cement cover with frame, earth work etc. complete as
per approved drawing including disposal of surplus earth within a lead of 50 mtr:- Size 200x100x130 cm.
(for 10 users) with 115 mm thick RCC (M-20) slab with Tor steel reinforcement 8mm ϕ @15 cm c/c
bothways including shuttering complete in all respect
1.00 Each
143 Add extra if R.C.C slab of designed thickness & reinforcement is provided on manhole in place of stone
slab( Actual area of R.C.C slab to be measured). Septic Tank
20.00 Sqm.
144 Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar
above 30 CM thick wall in: Cement Mortar 1:4 ( 1-Cement : 4-Sand).
25.47 Cum.
cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost
of centering, shuttering and reinforcement for Beams, suspended floors, roofs, griders having slopes up
to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral
staircases etc.
M20 grade Nominal Mix / Design Mix
9.96 Cum.
146 Construction Of Tube Well upto 100mtr depth and above in all type of rocks by DTH system and over
burden to accommodate casing pipe of followinf sizes in all types of soil and over burdens including
lowering of casing pipes but excluding cost of casing pipes as per IS:2800(Part I & II) 1979 specifications
the work would be completed after obtaining sand free water. the tube well should have throughout bore
as pere nominal dia. of casing pipe (site to be verified by approved geologist):
150mm Dia nominal bore.
120.00 Mtr.
147 Supply of ERW M.S. black casing pipe ISI marked (IS:4270/1992) of grade Fe410 of following sizes at site of
work.
150 mm Nominal bore of pipe
30.00 Mtr.
148 S & F tube well cover of M.S. Sheet (6mm thick) with nuts and bolts complete for casing size 150 mm dia
1.00 Each
149 S & F M.S. clamp set of 50x 6 mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of
submersible pump set.
1.00 Each
150 Providing & Fixing of HDPE pipe ISI mark (IS:4984/95) for water supply (suitable for submersible & jet
pump) with required fittings
for vertical installation 63 mm OD 6 kg / cm2
160.00 Mtr
151 Horizantal installation 63mm OD 4kg/cm2
100.00 Mtr
152 Supply of strainer pipes made of ERW M.S. black pipe ISI mark of following sizes at the site of work
including required size of slotting as per IS:8110-1985.
150 mm Nominal Bore.
80.00 Mtr.
153 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC
insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC
insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS
( IS:9537 P - III ) virgin material PVC conduit & it's ISI marked (IS:3419-1988) accessories, round tiles, 1.2
mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face
plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing
etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring
accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work
refer Annexure 'A' attached with this BSR
79.00 Each
154 Medium point (up to 6 mtr.)
209.00 Each
155 Long point (up to 10 mtr..)
277.00 Each
156 Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed
flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible
copper earth conductor 1.1 kV grade(IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit &
it's ISI marked (IS:3419-1988)accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth
terminal, 10 A modular switch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws,
making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated
sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical
parameters of product / work refer Annexure 'A' attached with this BSR
On board
225.00 Each
157 Medium point (up to 6 mtr.)
2.00 Each
158 Long point (up to 10 mtr..)
66.00 Each
159 Supplying and fixing of power plug point with Modular accessories as per PWD specification for electrical
Works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal/connector on
surface or in recessed with suitable size of modular face place with grid plate and cover plate including
cost of ISI marked modular 16 amp. Switch (IS :3854) and 6/16 amp. socket outlet (IS:1293) making
connection , testing , etc. as required. For specification of Wiring accessories refer Chapter E - 07 related
item & For additional technical parameters of product / work refer Annexure 'A' attached with this BSR
54.00 Each
160 Providing & Fixing of following modular accessories as per PWD specification for electrical Works, made
out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws &
silver alloy contact tip with IP-20 rating , including all as per pre approved by Engineer in charge,making
connections, testing etc. as required. For additional technical parameters of product / work refer
Annexure 'A' attached with this BSR
Blanking plate
150.00 Each
161 Modular MCB 6 A to 32 A DP (IS:8832 marked)
4.00 Each
162 Providing & Fixing of modular type 120 W Step Fan regulator duly ISI marked (IS 11037:1984 ) with CM/L
no. printed made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and
captive screws & silver alloy contact tip with IP-20 rating , including all as per pre approved by Engineer
in charge,making connections, testing etc. as required. For additional technical parameters of product /
work refer Annexure 'A' attached with this BSR
5 step fan regulator 2 Module 360 dgree rotating
116.00 Each
163 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD
specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire
should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt
loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS
10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS
conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as
required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For
additional technical parameters of product / work refer Annexure 'A' attached with this BSR
1 x 1.5 sq.mm
1500.00 Mtr.
164 2 x 2.5 sq. mm. + 1x1.5sqmm
1280.00 Mtr.
165 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm
835.00 Mtr.
166 2 x 6.0 sq. mm. + 1 x 4 sq. mm
400.00 Mtr.
167 4 x 10.0 sq.mm
400.00 Mtr.
168 1x 4.0 Sq.mm.
450.00 Mtr.
169 2 x 6.0 sq. mm. + 1 x 2.5 sq. mm.
5.00 Mtr.
170 Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed
)Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2
mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, powder painted complete with reversible door
(for double door DB only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper
earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making
internal DB terminations with copper lugs, Ferrules, detachable gland plate, including making
connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type
test reports & All as per pre approved by Engineer in charge. For additional technical parameters of
product / work refer Annexure 'A' attached with this BSR
Glazed door (Three phase) IK-09 and IP-43 with Metal end box
6 Way
9.00 Each
171 Glazed door (single phase) IK-09 and IP-43 with Metal end box
12 Way (12+2)
9.00 Each
172 Glazed door (single phase) IK-09 and IP-43 with Metal end box
8 Way (8+2)
1.00 Each
173 Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping
characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS
8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum ,
energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line
load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum
electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including
making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab
type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of
product / work refer Annexure 'A' attached with this BSR
Single pole MCB (With B/C curve tripping Characteristics)
6 A to 32 A rating
260.00 Each
174 Double pole MCB(With B/C curve tripping Characteristics)
3.00 Each
175 40A rating
10.00 Each
176 Four pole MCB(With B/C curve tripping Characteristics) 50/63 A rating
9.00 Each
177 S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along with ISI
marked (IS:3419-1988) accessories as required in recess including cutting the wall, covering conduit and
making good the same as required. For additional technical parameters of product / work refer Annexure
'A' attached with this BSR
20 mm
1220.00 Mtr.
178 25 mm
1020.00 Mtr.
179 40 mm
380.00 Mtr.
180 Making of hole in wall (brick/stone) of required and placing NP-2 RCC pipe ring of required size for
housing exhaust fan and making good the same, with cement plaster required of following size. All as per
pre approved by Engineer in charge. For additional technical parameters of products/ work , refer
Annexure "A" attached with this BSR . Up to 457 mm size
19.00 Each
181 P & F 1.2mm thick M.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm
dia rod fan hook with 100 mm length extended on each side . All as per pre approved by Engineer in
charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR
116.00 Each
182 Providing & Fixing of Heavy duty capacitor start, copper wound Double ball bearing 900/1400 RPM single
phase Exhaust fan conforming to IS:2312 ISI marked in existing opening including making connections
testing etc. as required. All as per pre approved by Engineer in charge. For additional technical
parameters of products/ work , refer Annexure "A" attached with this BSR .
300 mm sweep(900/1400 RPM)
19.00 Each
183 P & F of Gravity Louver shutter of superior quality made out of frame of 18 swg M.S. sheet & Louvers
made from 24 swg MS Sheet with enamel paint including cost of nuts, bolts, etc as reqd. All as per pre
approved by Engineer in charge. For additional technical parameters of products/ work , refer
Annexure "A" attached with this BSR .
Up to 380 mm size
19.00 Each
184 Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder
coated Extruded aluminium housing with in built driver , System lumen efficacy ≥ 110 lm/Watt output,
internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 ,
life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT
3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not
more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.).
Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its
own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report
from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical
1170mm(+/-10%) LED batten with min. lumen output 2200 lm
175.00 Each
185 Providing & Fixing of IP-20 LED Recessed / Surface Mounted, Round / Sqaure SMD Mid Power LED
Downlight with power coated die-cast aluminum housing with UV Stabilized non yellowish Diffuser with
BIS complience 2.5 KV surge protected Isolated driver, with Short & Open circuit protection, having
efficiency > 85% . System Lumen efficacy of ≥ 110 lm / watt, THD < 10 % , Pf.≥0.95, CRI >80, life time of
minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K/
5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the
specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures
Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.
OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80)
certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge. For
additional technical parameters of products/ work , refer Annexure "A" attached with this BSR
Surface Mounting (with extruded alumn. Housing )
Minimum lumen output 1950 lm
103.00 Each
186 Providing & Fixing of IP20, 2'x2' LED Surface/ Recessed mounting Mid power SMD type LED Light fixture
not less than 50mm housing depth made from CRCA sheet steel housing, high purity / transmisivity UV
stabilized Non -yellowish diffuser for uniform light distribution. High efficiency with 4 KV internal/external
surge protection BIS certified isolated driver having efficiency > 85% , with Short & Open circuit protection
(Integral with light fixture). System lumen efficacy of ≥ 120 lm/Watt ,THD < 10 % , p.f.≥0.95,CRI >80 , life
time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K /
4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than
the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures
Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.
OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80)
certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge. All as
per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer
Surface Moutning
16.00 Each
187 Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to
IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS
8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831
in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie)
including testing etc. as required of following size. OEM must have it's own in house NABL accrediated
Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work
refer Annexure 'A' attached with this BSR 10.0 Sq. mm x 2 core
30.00 Mtr.
188 Pipe Earthing as per IS:3043- 1987 with 3.0 Mtr. Long, 40 mm dia. ' B ' class G.I. Pipe IS: 1239 (Part-1)
2004, Equivalent to BS : 1387 with perforated holes of 12 mm dia ,including all accessories like nut, bolts,
reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber
with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm,
Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. and embodying the pipe complete with
alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required
& must record by engineer in charge during site visit and ensure to enter in measurment book.All as per
1.00 Set
189 Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including
riveting, soldering, saddles, making connection with GI/Cu purity purity >95% thimble etc. as required.
All as per pre approved by Engineer in charge. For additional technical parameters of products/ work ,
refer Annexure "A" attached with this BSR .
8 SWG tinned copper Wire
15 Mtr.
190 Supply & Laying following size' B ' class , G.I. Pipe confirming to IS : 1239 P - 1 ( 2004 ) with accessories
like bend, socket etc. for laying earth conductor/ strip / cable in ground/ surface/ recess as required. All
as per pre approved by Engineer in charge. (Earth Excavation will be Paid Extra)All as per pre approved by
Engineer in charge. For additional technical parameters of products/ work , refer Annex ure "A"
attached with this BSR .
32mm dia
2 Mtr.
191 Providing & Fixing of BEE Star rated copper wounded double ball bearing capacitor start, aluminium
body & Metallic blade ceiling fan Conforming to all the performance requirements laid down in IS
374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod
up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated
flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer
in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this
BSR .
1200 mm Sweep BEE 1 Star rated (service value >=4.0 to < 4.5 )
116.00 Each
192 Providing & Fixing of 400 mm Sweep BLDC technology Oscillating type Wall mounting / Pedestal type
fans with Three speed, ON and OFF position, Double Wall bearing with front and back 120 or more ribs
guard; Three no. blades, noise level should be <= 75 dB, including fixing with anchor bolts, making
connection testing etc. as required. ( With Remote ) All as per pre approved by Engineer in charge. For
additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .
Wall mounting type with Service value 2.0 CMM /W, Min. Air Delivery 71 CMM
4.00 Each
193 Providing & Fixing of of Double ball bearing, copper wounded capacitor start single phase metallic blade
fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor ,making
connections, testing etc. as required. All as per pre approved by Engineer in charge. For additional
technical parameters of products/ work , refer Annexure "A" attached with this BSR . 300 mm sweep
2.00 Each
194 Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to
IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS
8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831
in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie)
including testing etc. as required of following size. OEM must have it's own in house NABL accrediated
Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work
refer Annexure 'A' attached with this BSR
70.0 Sq. mm 3.5 core
100.00 Mtr.
195 Supplying and making one end termination with Nickel plated heavy duty brass single compression gland
(as per IS 12943-1990)) SIBG type consisting of Check Nut, Gland Body, Metal Washer(3 Nos.), Outer Seal
Rubber Ring, Compression Nut, heavy duty aluminium lugs (as per IS 8309 -1993) duly crimped with
crimping tool, PVC tape as per IS 8337-1976 of following size of PVC insulated & PVC sheathed/ XLPE
aluminium conductor cable of 1100 volt grade as required.All as per pre approved by Engineer in charge.
For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .
3.5 x 70.0 sq.mm
4.00 Set
196 Supply and installation of high tensile low carbon steel rod molecularly bonded with 99.9 % Copper
thickness (250 microns) and confirming to UL 467, IS/IEC 62561-2 of following size and length and as per
point mentioned (a), (b), [c), (d), (e) below :-
17.2 mm thick and 3 Mtr. Long
2.00 Each
197 Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including
riveting, soldering, saddles, making connection with GI/Cu purity purity >95% thimble etc. as required.
All as per pre approved by Engineer in charge. For additional technical parameters of products/ work ,
refer Annexure "A" attached with this BSR .
8 SWG copper Wire
50.00 Mtr.
198 Providing & Fixing of IK08, IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture
made of powder coated single piece pressure die cast aluminum material with heat dissipation fins on
housing with UV stabilized PC (UV stablization report submitted for UV cover ) /Toughened Glass cover
and secondary lens on each LED & should be SMD type of 3 to 5 watt each . The System efficacy >=125
lm/ wt and potted driver & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with High
voltage Cutoff @>=300 V AC and Auto resetting Safety , Power Factor >0.95 driver Efficiency
>85% ,THD(I) <10% Humidity 10% to 90% RH Working Temp -5C to 45C . driver current <750mA. The
luminaire shall be BIS certified and Trade mark certified. Life Expectancy Equal or more than 50000
burning hrs with Minimum 70% lumen maintened , CRI >70 and CCT 5700K +355K. Surge protection shall
be min ≥ 4 KV internal and min 10 KV external inside driver compartment. driver should be Phase to
phase protection of 440 V for 4 Hrs. Manufactures Word Mark/Name Engraved/Embossing on die cast
housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have
its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/
report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved
by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A"
attached with this BSR . 4.00 Each
LED Street Light fixture with Minimum lumen output 2450 lm
199 LED Street Light fixture with Minimum lumen output 7500 lm
2.00 Each
200 LED Street Light fixture with Minimum lumen output 3700 lm
2.00 Each
201 Providing & Fixing of Street light bracket made out from following size of ' B ' class , Medium class G.I.
Pipe confirming to IS : 1239 P - 1 ( 2004 ) with heavy duty pole clamp, Saddles suitable fastners etc. as
required. All as per pre approved by Engineer in charge. For additional technical parameters of products/
work , refer Annexure "A" attached with this BSR .
32 mm Dia.
6.00 Mtr.
202 SITC of 3 /4 pole current limiting Moulded case circuit breaker (MCCB) made of flame retardent & heat
resistant material having following current rating, short circuit breaking capacity at 440/415 V, 50 Hz;
O/L & S/C settings , conforming to IS/IEC 60947 P -2 :2003 with front face and centralised adjustable, trip
free mechanisum, true contact position indicator, line load interchangeability, designed for both
horizontal & vertical mounting without any adverse effect on electrical performance, suitable for
operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive
isolation capability, push (test) to trip, trip time less then 10 ms under s/c condition, Breaking capacity
Ics = 100% Icu. U imp =8 KV, rated insulation voltage 690 V. provision for UVR , shunt trip , earth fault
trip, door interlock, pad lock & rotary handle , including making connections etc. as required.OEM shall
have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution All as per pre
approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A'
attached with this BSR
4 pole MCCB With Thermal Magnetic release
up to 100 Amp , 25 kA, adjustable O/L & adjustable S/C setting,
6.00 Each
203 200 Amp , 25 kA, adjustable O/L & adjustable S/C setting,
1.00 Each
204 Supplying and fixing of Aluminium (IEC 60105 ISO 209-1,2) / Copper (IEC 60028) bus bar by means of
SMC / DMC type insulator with standard short circuit withstand capacity , high tensile nuts and bolts
spring washers in existing panel including bending , cutting in required shape and size and colour coding
with heat shrinkable PVC sleeves. All as per pre approved by Engineer in charge. For additional technical
Electrolytic grade (Cu-ETP) Tin Coated annealed copper bus bars IACS 100% grade
20.00 Kg.
205 SITC of IP-42 and general construction confirming to IS:8623 : 1993, wall/ free standing floor mounted
dust and vermin proof compartmentalised cubical panel as specifications and Other parameters required
as per point (a) ,(b), (c),(d), (e), (f), (g), (h) as below:-
(h) only outer surface area on all sides shall be measured & panel to be fabricated only from CPRI
approved fabricator only (CPRI Test certificates to be submitted)All as per pre approved by Engineer in
charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this
BSR .
10.00 Sqmtr.
206 Providing & Fixing of IS: 13875 & IEC :61326 confirming LED Digital type (up to 500) V range Volt meter /
Direct- Ammeter / CT oertated ammeter/ Frequency meter / KWH meter / Multi Function Meter / Power
analyzer of class 1 accuracy as per IS : 1248 of size 96mm x 96 mm including making connection by PVC
insulated copper conductor with PVC sleeves / channel etc. as required. All as per pre approved by
Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached
with this BSR .
Three phase Ammeter with Inbuilt Selector Switch
2 Each
207 Three phase Voltmeter with Inbuilt Selector Switch
2 Each
208 Providing & Fixing of BIS approved Current Transformer as per PWD specification for electrical Works ,ISI
marked as per IS 2705-1992/ conforming to IEC 60044-1, with secondary terminal of CT shall be brought
out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with
all necessary support in existing panel including connection etc. as required Current transformer Ring
Type Tape Wound/Resin Cast Wound as per IS 16227 with, Accuracy Cl, CT ratio and burden as specified.
ISF<=5, Cu cross section of secondary wire 1.5sqmm (minimum), including all necessary support in
existing panel including connection etc. as required . All as per pre approved by Engineer in charge.All as
per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer
Annexure "A" attached with this BSR
C T Class 1, Ratio 200/5 to 300/5, Burden 10 VA.
6.00 Each
209 Providing & Fixing of selector switch of 10 A for voltmeter using high grade engineering material to
international standards with cam assembly insulation of glass filled polyamide with high tracking index.
For reliable and stable electrical and mechanical endurance double butt contacts with silver bi-metal on
copper should provided . contact assembly is of operating temp range -25 degree C to 55 degree C,
frequency upto 10 KHz. switch life under std. op. conditions shall be mechanically minimum 50000
operations @300 cycles/ hour and electrically 10,000 operations at 100% rated duty for 100 cycles/ hour
including making connection etc. as required . All as per pre approved by Engineer in charge. For
Voltage Between Phases with OFF ( 4 Position )
2.00 Each
210 Providing & Fixing of CT linked selector switch of 10 A for Ampere meter (4 position ) using high grade
engineering material to international standards with cam assembly insulation of glass filled polyamide
with high tracking index. For reliable and stable electrical and mechanical endurance double butt contacts
with silver bi-metal on copper should provided . contact assembly is of operating temp range -25 degree C
to 55 degree C, frequency upto 10 KHz. switch life under std. op. conditions shall be mechanically
minimum 50000 operations @300 cycles/ hour and electrically 10,000 operations at 100% rated duty for
100 cycles/ hour , including making connection etc. as required .All as per pre approved by Engineer in
charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this
BSR .
2.00 Each
211 Providing & Fixing of 110/220 V, unibody LED Indicating lamp IEC 60947 with integral circuit, IP 65 above
panel & IP 20 terminal block, Approx. body dia for panel not less then 20 mm, length min. 50mm, front
LED cover dia min. 29 mm, contact material phospher bronze for Led, PCB contacts shall be of brass (tin
plated), impulse dielectric tested for 2.5 KV, Rated insulation resistance shall be 100 M ohm at 500VDC
including connection etc. as required. All as per pre approved by Engineer in charge. For additional
technical parameters of products/ work , refer Annexure "A" attached with this BSR .
Red/yellow/Green colour
6.00 Each
212 Providing & Fixing of ISO certified company made on load change over switch, front handle operated, four
pole 415 V as per PWD specification for electrical Works conforming to IS/lEC 60947-3 : 1999 including
connections , testing etc. as required .in the following rating. Appropriate type test certificate / OEM test
report shall be submitted . All as per pre approved by Engineer in charge. For additional technical
1.00 Each
213 Providing & Fixing of ding dong/musical chime bell as per PWD specification for electrical Works,
including making connection testing etc. as required.All as per pre approved by Engineer in charge. For
2.00 Each
214 Supply & Fixing of Dry Powder Agent (as per IS 4308:2019), ABC type Fire Extinguisher (Stored Pressure
type) conforming to IS:15683:2018 , Powder coated Internal & External Surface Deep drawn cylinder
body of Mild Steel CR2 grade conforming to IS: 513, Squeeze grip Forged brass release valve with Inbuilt
safety release device, Diaphragm Type, 0 to 28 bar range pressure gauge, 450 mm long EPDM discharge
tube, QR code for Product Traceability including Fixing on wall with suitable Anchor Fasteners as required
of following capacity. Test Certificates of all the Parameters along with Hydro test & Burst test (For
Cylinder Body) Certificate from OEM / External NABL Accrediated Lab is to be submitted. All as per pre
6 kg
6.00 Each
215 Providing & Fixing of Electrical insulating rubber matts as per PWD specification for electrical Works, ISI
marked confirming to IS: 15652 / 2006 with one side anti skid abberation marks and pasting the mat
with synthetic rubber adhesive as required. All as per pre approved by Engineer in charge. For additional
technical parameters of products/ work , refer Annexure "A" attached with this BSR .
11 KV, Class B 2.5 mm thick with proof voltage 22 KV AC (rms) and Break Down Voltage 45 KV AC (rms)
2.00 Sqmtr
216 SITC of Radial / mixed flow ISI marked water and anti-corrosive liquid filled submersible motor pump sets
suitable for 100/150mm dia borewell. The size of adopter fixed on top of the motor should exceed the
top of coupler , for safegaurd the coupler. The construction material of motor and pump should match IS:
8034 : 2018 and IS: 9283 guideline. The radial flow pumpset should operate at 5 star energy efficiency
level of BEE and mixed flow pump set should operate at 3 star energy level of BEE, accompained by valid
BEE certificate. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008, &
IS12615:2011 with required accessories including making connection suitable for Bore well. The job
includes labour part of lowering of riser pipe G.I./ H.D.P.E. with rope, cables & pump, installation of
complete fitting and accessories, jointing of electrical cables up to Starter. All labour for testing of
submersible pumps set and supply of water to water mains, complete in all respect. OEM shall have
submit NABL / CPRI / ERDA accrediated lab type test certificate before execution. All as per pre
100 mm diameter Submersible pump shall have following HP Rating, phase, Head range, Discharge range
respectively.
2.0 HP, 1-Ø, (7- 95)Mtr, (55-22) LPM
1 Each
217 SITC of Single Stage, water cooled, High Speed (2880 RPM), Horizontal, Centrifugal, Openwell
Submersible pumps set pre filled with coolent water and fitted with mechanical seal - T/C Vs T/C, Thrust
bearing shall be of carbon + S.S.The stator body of single phase pump shall be of SS and rest of all shall
be of cast iron. All casting parts should be cathod electro deposition (CED) coated and other construction
material should be confirming to IS : 14220: 2018 . The overall performance of pump shall confirm to BEE
energy efficiency level of 3 star. Valid BEE certificate from OEM must be submitted for the same. Motor
should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008, & IS12615:2011, including making
connection etc as required complete in all respect. OEM shall have submit NABL / CPRI / ERDA
accrediated lab type test certificate before execution. All as per pre approved by Engineer in charge. For
additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . 3.0 HP,
3-Ø, (17 -27) Mtr, (680 - 300) LPM
1.00 Each
218 Providing & Fixing of HDPE pipe Confirming to IS:4984:2021 for water supply suitable for submersible
& jet pump with required fittings ie socket, elbows, tee etc. complete in all respect. All as per pre approved
by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A"
attached with this BSR . 40 mm OD 6 kg / cm2
125.00 Mtr.
219 SITC of Contactor OEM Fabricated DOL/Star-Delta Starter panel with switchgear selection as per Type-2
Cordinatiom Chart and made out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of
over load protection relay, short circuit & single phasing protection, Illuminated ON / OFF push buttons,
ammeter, voltmeter, indicating lamps etc. suitable for following rating motors complete in all respect. All
as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer
Annexure "A" attached with this BSR . 2.0 HP to 3.0 HP (DOL starter)
1.00 Each
220 Providing & Laying of Polypropylene rope Confirming to IS:5175 for submersible pump of following
sizes. complete in all respect. All as per pre approved by Engineer in charge. For additional technical
125.00 Mtr.
221 P/Laying ISI marked P.V.C. insulated submersible cable confirming to(IS:694) and as per IS 8130 : 2013 of
1.1 kV grade . Wire should be made from 99.90 % purity copper, stranding in acc. to IS:8130/IEC 60228
for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame
retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, existing pipe / open trench /
Cable tray / on surface including making connection etc. as required. For additional technical parameters of
product / work refer Annexure 'A' attached with this BSR 4.0 Sq.mm 3 core flat / Round
130.00 Mtr.
222 Providing & Fixing of Vertical(BEE 5 star rated) / Horizontal( BEE 3 star rated) storage water heater with
outer casing made of Engineering Plastic sheet (Upto 25 Ltr) / Metal rust proof Body (35 & 50 Ltr), Glass -
line / Titanium Enamel coated Pressure Pump Compatible 8 bar pressure Inner tank, Glass Line Coated ,
mineral filled heating element, stem type, snap action adjustable thermostat , Dual indicating lamps
Injected PUF insulation, Multi Function Valve etc. as required held in position with 2/4 no. 10/12 mm
anchor Fastener, duly wired with 3 core 2.5/4.0 Sqmm PVC insulated & sheathed copper conductor and 16
A/25A three pin plug top with Portable Residual Current Device ( PRCD ) , including making inlet, outlet
Flexible alloy connection, testing etc. as required. All as per pre approved by Engineer in charge. For
additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .15 Ltr.
1.00 Each
223 P & F in position frame made out of M.S. angle (riveted or welded) finished with two coats of red oxide
and two coats enamel paint including cutting, welding, holes etc.of following sizes as required.For
additional technical parameters of product / work refer Annexure 'A' attached with this BSR 40mm x 40mm
x 5mm
15.00 Mtr.
224 Supply , Installation, Testing and Comissioning of IS:1475 marked self contained drinking water cooler
with hermetically sealed compressor,non CFC refrigerent suitable for operation on 230V/1pH/50Hz AC
supply,Full stainless steel (SS304)body (0.8 mm thick) and tank (0.5 mm thick) , stainless steel water
tray,minimum two nos Brass Chrome plated faucets and suitable drainage system complete in all respect
with required height MS fabricated and Painted Angle iron frame ( Cost of frame to be paid
Extra )complete in all respect of the following capacity. All as per pre approved by Engineer in charge.
For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .
cooling capacity 150 Ltr./Hr. and storage capacity 150 Ltrs
3.00 Each
225 Providing & Fixing of AC operated heavy duty 230 /440 Volt power contactor as per PWD specification
for electrical Works, ISI marked IS/IEC 60947-4-1 : 2000 having provision of mechanical interlocking,
auxilary contacts, Din rail mounting type including making connections, testing etc. as required. All as per
3 pole Power contactors with following AC 3 Rating
Up to 12 Amp
3.00 Each
226 13 to 25 Amp
3.00 Each
227 Providing & Fixing of self healing IP20 MPP type shunt capacitor (banks) conforming to IS:13340-41 /
IEC :831-1&2 OR IEC : 60831-1& 2 in existing panel or parallel with load terminals , the capacitor shall be
fitted with discharge resistors, pressure sensitive disconnector ( PSD ) and shall have dissipation factor less
than 0.0025 at 50 Hz, Operating loss less than 0.30 Watt per KVAR. Min over current capacity 1.8 times
rated current & peak inrush current min. 300 times of rated current, llife expectancy greater than 100000hrs
(temp class - 25 D) in 440 V/480 V Capacitor and for 525 V should life expectancy minimum 1,65,000 hrs
(temp class - 25 D) including making connections, testing etc. as required.All as per pre approved by
Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached
with this BSR . Heavy duty Three phase 440 V, 50 Hz cylindrical type capacitor (Bank)
20.00 Kvar
228 Providing & Fixing of IP54 microprocessor based 3 CT’s for all 3 phase sensing compensation power
factor correction relay Size 139mm x 139 mm, Operating Voltage 415/440 V , IEC / EN 61000-6-(2&4)
having 3 CT sensing, sensitivity up to 50 milli amp secondary current , self analysing auto c/k setting
according to targeted power factor setting, the relay shall have digit display unit for display of real power
factor, targeted power factor, lag/lead capacitor switching status, alarm output for under current, over
current, insufficient compensation, communication interface with RS 485, indication of switching on units,
auto/manual status, and shall have over load protection, no volt release , having multi parameter like KW,
KVA, KVAR, RMS Value, step switching time 2 sec to 1800 sec. Lead & Lag parameters, metering facility
and 3 no. Class- 0.5 Cast Resin CT ( refer CT specs in this chapter )for sensing the relay including making
coonection with 1.5 Sq.mm copper wire etc. as required. All as per pre approved by Engineer in charge. For
additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .6 to 8
stage
1.00 Each
229 SITC of Ro water system with filtration stage = Particalate filter - membrane life enhancer filter - sediment
filter - pre carbon filter - RO membrane filter - Post carbon filter , Input power - 230 V AC , 50Hz ,
percentage of rejection TDS-90% or better having following fitures (a) Double purification By RO with
RSS or latest technology with TDS indicator , (b) Spin welded RO membrane housing to prevent tempring
(c) push fit component for leak proof performance (d) Fully automatic operation with auto start & auto off
(e) SS/ABS construction for corrosion free lifespin (f) Equally suitable for water from from all bore wells ,
overhead storage tank water tankers & even municipal tapos (g) RO membrane Flushing -Auto @ Every
start , Every stop & every one hours of working for one minute , complete in respect with following
capacity make : Kent / Eurka Frobes/ Ion Exchange / Electrolux / Voltas
3.00 Each
230 Providing and laying in position specified grade of cement concrete for all RCC structural elements upto
plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3
coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering,
shuttering and reinforcement.
10.11 Cum.
231 Random Rubble stone masonry with hard stone in superstructure above plinth level and upto five level
above 30cm. thick walls in : Cement Mortar 1:6 ( 1-Cement : 6-Sand).
173.46 Cum.
232 Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor
five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3
coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering,
shuttering and reinforcement for Walls (any thickness) including attached pilasters, buttresses, plinth and
string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.
13.63 Cum.
233 Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine
finish : 25 mm thick
1555.56 Sqm
234 Finishing wall with water proofing cement paint of approved brand and manufacture and or required shade
to give an even shade including all scaffolding: New work (Two or more coats applied @ 3.84 kg/10
sqm).
1555.56 Sqm.
235 Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with
holdfast and fittings complete as per design and drawing including cutting welding and fabrication with
priming coat of red oxide
3200.00 Kg.
236 Extra if square,rectangular hollow tubelar sections are used or grill made by flats only
2200.00 Kg.
237 Providing and fixing concertina coil fencing with required dia 610 mm (having 15 nos. round per 6 metre
length) up to 3m height of wall with existing angle iron 'Y' shaped placed 2.4 m or 3.00 m apart and with 9
horizontal R.B.T. stud tied with GI staples and GI clips to retain horizontal including necessary bolts or GI
barbed wire tied to angle iron all complete as per direction of Engineer In Charge with reinforced barbed
tape (R.B.T.)/Spring core(2.5 mm thick) wire of high tensile strength of 165 kg/sq.mm with tape (0.52 mm
thick) and weight 43.478 gm/metre (Cost of MS angle, CC block shall be paid extra)
258.17 Mtr.
238 Providing and fixing steel glazed window frame made out of 80x40 mm hollow sheet section of 16 gauge
thickness, joint mitred welded and grinded including hold fast of steel lugs 13mm x 3mm and 15 Cm long
embedded in C C block 15 x 10 x 10 Cm of 1:3:6 nominal concrete and including fixing of pivoted hinges
of superior quality, window shutters made out of 50 x 25.0 mm hollow steel section 15 mm paitam of 18
gauge thickness, joint mitred and grinded including 10mm x 10mm square bars welded to frame for paitam
fixing float glass 4mm thick panes with glazing clips and metal sash putty and fixing of shutters frames
peg stay, U shape handle 100 mm long, tower bolts 100 mm long of steel powder coated superior quality
including fixing and jointing with frame hinges priming coat with steel primer complete in all respect as per
direction of Engineer-in –charge Window openable.
6.50 Sqm
239 Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick
cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to
match the shade of the slabs, including rubbing and polishing complete For area of each slab from 2001 to
5000 Sqcm
3.48 Sqm
240 Finishing walls with Acrylic Smooth exterior paint of required shade including all scaffolding.
New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing
cement paint applied @ 2.20 kg/ 10 sqm ).
107.95 Sqm
stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe
with clamps at 1 metre spacing. This includes jointing of pipes & fittings with one step CPVC solvent
cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on
wall)
20mm nominal size
15.00 Mtr.
242 25 mm nominal size
10.00 Mtr.
243 Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas
(exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth,
lead upto 50m and lift upto 1.5 m , disposed earth to be levelled and neatly dressed : All kinds of soil
114.11 Cum.
244 Providing and laying in position cement concrete including curing, compaction etc. complete in specified
grade excluding the cost of centering and shuttering - All work up to plinth level. 1:4:8 (1 cement : 4 coarse
sand : 8 graded stone aggregate 40 mm nominal size).
33.62 Cum.
245 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement in position to
the required line, level and curvature jointed with cement mortar 1:3 (1 cement : 3 coarse sand ) including
making joints with without grooves (thickness of joints except at sharp curve shall not to more than 5mm)
including making drainage opening wherever required complete including painting etc. as per direction of
Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb
stone shall be approved by Engineerin- charge).
14.15 Cum.
246 Providing and laying of paver block as per IS 15658 : 2006 (Indian standard for precast concrete block for
paving- specification) and IRC : SP:63-2004 (guidelines for the use of interlocking concrete block
pavement) Category ‘B’ Denated only two side like I,Z,T shape etc. as per IRC SP 63:2004
334.44 Sqm
247 Mehrab & Chatri
1.00 Ls
Total in Figures
Quoted Rate in Figures Select

Quoted Rate in Words
Percentage BoQ
100
LE
levent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the
es only ) NUMBER NUMBER # TEXT #
Estimated Rate TOTAL AMOUNT in TOTAL AMOUNT

in Rs. P In Words
Rs. P
6 53 55
#VALUE!
9.00 #VALUE!
#VALUE!
178.00 #VALUE!
#VALUE!
3,302.00 #VALUE!
#VALUE!
64.00 #VALUE!
#VALUE!
5,003.00 #VALUE!
#VALUE!
243.00 #VALUE!
#VALUE!
47.00 #VALUE!
#VALUE!
5,678.00 #VALUE!
#VALUE!
5,254.00 #VALUE!
#VALUE!
157.00 #VALUE!
#VALUE!
340.00 #VALUE!
#VALUE!
375.00 #VALUE!
#VALUE!
77.00 #VALUE!
#VALUE!
2,838.00 #VALUE!
#VALUE!
932.00 #VALUE!
#VALUE!
4990.00 #VALUE!
#VALUE!
553.00 #VALUE!
#VALUE!
64.00 #VALUE!
#VALUE!
673.00 #VALUE!
#VALUE!
609.00 #VALUE!
#VALUE!
70.00 #VALUE!
#VALUE!
3,434.00 #VALUE!
#VALUE!
1,305.00 #VALUE!
#VALUE!
88.00 #VALUE!
#VALUE!
143.00 #VALUE!
#VALUE!
30.00 #VALUE!
#VALUE!
674.00 #VALUE!
#VALUE!
36.00 #VALUE!
#VALUE!
748.00 #VALUE!
#VALUE!
911.00 #VALUE!
#VALUE!
48,847.00 #VALUE!
#VALUE!
2,778.00 #VALUE!
#VALUE!
2,208.00 #VALUE!
#VALUE!
2,244.00 #VALUE!
#VALUE!
1,020.00 #VALUE!
#VALUE!
555.00 #VALUE!
#VALUE!
1,991.00 #VALUE!
#VALUE!
141.00 #VALUE!
#VALUE!
100.00 #VALUE!
#VALUE!
83.00 #VALUE!
#VALUE!
5,174.00 #VALUE!
#VALUE!
503.00 #VALUE!
#VALUE!
2,869.00 #VALUE!
#VALUE!
3,090.00 #VALUE!
#VALUE!
617.00 #VALUE!
#VALUE!
65.00 #VALUE!
#VALUE!
3,895.00 #VALUE!
#VALUE!
111.00 #VALUE!
#VALUE!
143.00 #VALUE!
#VALUE!
277.00 #VALUE!
#VALUE!
1,775.00 #VALUE!
#VALUE!
275.00 #VALUE!
#VALUE!
317.00 #VALUE!
#VALUE!
645.00 #VALUE!
#VALUE!
1,023.00 #VALUE!
#VALUE!
627.00 #VALUE!
#VALUE!
523.00 #VALUE!
#VALUE!
202.00 #VALUE!
#VALUE!
227.00 #VALUE!
#VALUE!
139.00 #VALUE!
#VALUE!
34.00 #VALUE!
#VALUE!
11.00 #VALUE!
#VALUE!
7.00 #VALUE!
#VALUE!
84.00 #VALUE!
#VALUE!
80.00 #VALUE!
#VALUE!
123.00 #VALUE!
#VALUE!
69.00 #VALUE!
#VALUE!
167.00 #VALUE!
#VALUE!
77.00 #VALUE!
#VALUE!
617.00 #VALUE!
#VALUE!
528.00 #VALUE!
#VALUE!
831.00 #VALUE!
#VALUE!
1,078.00 #VALUE!
#VALUE!
493.00 #VALUE!
#VALUE!
828.00 #VALUE!
#VALUE!
865.00 #VALUE!
#VALUE!
409.00 #VALUE!
#VALUE!
391.00 #VALUE!
#VALUE!
3080.00 #VALUE!
#VALUE!
5198.00 #VALUE!
#VALUE!
402.00 #VALUE!
#VALUE!
1645.00 #VALUE!
#VALUE!
2745.00 #VALUE!
#VALUE!
5062.00 #VALUE!
#VALUE!
575.00 #VALUE!
#VALUE!
62.00 #VALUE!
#VALUE!
279.00 #VALUE!
#VALUE!
376.00 #VALUE!
#VALUE!
476.00 #VALUE!
#VALUE!
289.00 #VALUE!
#VALUE!
167.00 #VALUE!
#VALUE!
196.00 #VALUE!
#VALUE!
262.00 #VALUE!
#VALUE!
343.00 #VALUE!
#VALUE!
757.00 #VALUE!
#VALUE!
101.00 #VALUE!
#VALUE!
164.00 #VALUE!
#VALUE!
242.00 #VALUE!
#VALUE!
463.00 #VALUE!
#VALUE!
590.00 #VALUE!
#VALUE!
783.00 #VALUE!
#VALUE!
477.00 #VALUE!
#VALUE!
1009.00 #VALUE!
#VALUE!
590.00 #VALUE!
#VALUE!
902.00 #VALUE!
#VALUE!
227.00 #VALUE!
#VALUE!
385.00 #VALUE!
#VALUE!
529.00 #VALUE!
#VALUE!
703.00 #VALUE!
#VALUE!
1464.00 #VALUE!
#VALUE!
314.00 #VALUE!
#VALUE!
7841.00 #VALUE!
#VALUE!
5881.00 #VALUE!
#VALUE!
3920.00 #VALUE!
#VALUE!
353.00 #VALUE!
#VALUE!
991.00 #VALUE!
#VALUE!
108.00 #VALUE!
#VALUE!
87.00 #VALUE!
#VALUE!
187.00 #VALUE!
#VALUE!
114.00 #VALUE!
#VALUE!
230.00 #VALUE!
#VALUE!
187.00 #VALUE!
#VALUE!
161.00 #VALUE!
#VALUE!
97.00 #VALUE!
#VALUE!
230.00 #VALUE!
#VALUE!
36.00 #VALUE!
#VALUE!
24.00 #VALUE!
#VALUE!
177.00 #VALUE!
#VALUE!
350.00 #VALUE!
#VALUE!
282.00 #VALUE!
#VALUE!
463.00 #VALUE!
#VALUE!
108.00 #VALUE!
#VALUE!
114.00 #VALUE!
#VALUE!
187.00 #VALUE!
#VALUE!
97.00 #VALUE!
#VALUE!
161.00 #VALUE!
#VALUE!
230.00 #VALUE!
#VALUE!
36.00 #VALUE!
#VALUE!
5489.00 #VALUE!
#VALUE!
22138.00 #VALUE!
#VALUE!
176.00 #VALUE!
#VALUE!
27322.00 #VALUE!
#VALUE!
215.00 #VALUE!
#VALUE!
3182.00 #VALUE!
#VALUE!
5185.00 #VALUE!
#VALUE!
666.00 #VALUE!
#VALUE!
1224.00 #VALUE!
#VALUE!
279.00 #VALUE!
#VALUE!
266.00 #VALUE!
#VALUE!
148.00 #VALUE!
#VALUE!
142.00 #VALUE!
#VALUE!
1527.00 #VALUE!
#VALUE!
359.00 #VALUE!
#VALUE!
578.00 #VALUE!
#VALUE!
772.00 #VALUE!
#VALUE!
357.00 #VALUE!
#VALUE!
726.00 #VALUE!
#VALUE!
920.00 #VALUE!
#VALUE!
580.00 #VALUE!
#VALUE!
22.00 #VALUE!
#VALUE!
461.00 #VALUE!
#VALUE!
398.00 #VALUE!
#VALUE!
22.00 #VALUE!
#VALUE!
81.00 #VALUE!
#VALUE!
122.00 #VALUE!
#VALUE!
185.00 #VALUE!
#VALUE!
531.00 #VALUE!
#VALUE!
48.00 #VALUE!
#VALUE!
170.00 #VALUE!
#VALUE!
6126.0 #VALUE!
#VALUE!
2990.00 #VALUE!
#VALUE!
2581.00 #VALUE!
#VALUE!
187.00 #VALUE!
#VALUE!
566.00 #VALUE!
#VALUE!
900.00 #VALUE!
#VALUE!
1745.00 #VALUE!
#VALUE!
40.00 #VALUE!
#VALUE!
56.00 #VALUE!
#VALUE!
115.00 #VALUE!
#VALUE!
348.00 #VALUE!
#VALUE!
128.00 #VALUE!
#VALUE!
3175.00 #VALUE!
#VALUE!
287.00 #VALUE!
#VALUE!
492.00 #VALUE!
#VALUE!
1620.00 #VALUE!
#VALUE!
2862.00 #VALUE!
#VALUE!
152.00 #VALUE!
#VALUE!
3643.00 #VALUE!
#VALUE!
163.00 #VALUE!
#VALUE!
448.00 #VALUE!
#VALUE!
1890.00 #VALUE!
#VALUE!
4699.00 #VALUE!
#VALUE!
1822.00 #VALUE!
#VALUE!
610.00 #VALUE!
#VALUE!
382.00 #VALUE!
#VALUE!
7010.00 #VALUE!
#VALUE!
148.00 #VALUE!
#VALUE!
2554.00 #VALUE!
#VALUE!
4942.00 #VALUE!
#VALUE!
3370.00 #VALUE!
#VALUE!
742.00 #VALUE!
#VALUE!
7112.00 #VALUE!
#VALUE!
15348.00 #VALUE!
#VALUE!
1301.00 #VALUE!
#VALUE!
3443.00 #VALUE!
#VALUE!
1689.0 #VALUE!
#VALUE!
1689.0 #VALUE!
#VALUE!
788.00 #VALUE!
#VALUE!
351.00 #VALUE!
#VALUE!
384.00 #VALUE!
#VALUE!
170.00 #VALUE!
#VALUE!
11691.00 #VALUE!
#VALUE!
328.00 #VALUE!
#VALUE!
4576.00 #VALUE!
#VALUE!
2043.00 #VALUE!
#VALUE!
25202.00 #VALUE!
#VALUE!
25922.00 #VALUE!
#VALUE!
94.00 #VALUE!
#VALUE!
5406.00 #VALUE!
#VALUE!
43.00 #VALUE!
#VALUE!
214.00 #VALUE!
#VALUE!
10304.00 #VALUE!
#VALUE!
367.00 #VALUE!
#VALUE!
75878.00 #VALUE!
#VALUE!
1033.00 #VALUE!
#VALUE!
1346.00 #VALUE!
#VALUE!
374.00 #VALUE!
#VALUE!
14995.00 #VALUE!
#VALUE!
56600.00 #VALUE!
#VALUE!
4934.00 #VALUE!
#VALUE!
3479.00 #VALUE!
#VALUE!
5609.00 #VALUE!
#VALUE!
211.00 #VALUE!
#VALUE!
53.00 #VALUE!
#VALUE!
96.00 #VALUE!
#VALUE!
9.60 #VALUE!
#VALUE!
266.00 #VALUE!
#VALUE!
3803.00 #VALUE!
#VALUE!
1002.00 #VALUE!
#VALUE!
84.00 #VALUE!
#VALUE!
222.00 #VALUE!
#VALUE!
282.00 #VALUE!
#VALUE!
175.00 #VALUE!
#VALUE!
3378.00 #VALUE!
#VALUE!
6103.00 #VALUE!
#VALUE!
786.00 #VALUE!
#VALUE!
100000.00 #VALUE!
#VALUE! #VALUE!
0.00 #VALUE!
#VALUE!
Please Enable Macros to View BoQ information
Q information

Boq 622014

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Boq 622014

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Boq 622014

Uploaded by

Copyright:

Available Formats

Validate Print Help Percentage BoQ

Tender Inviting Authority: DIRECTOR SWACH PROJECT UDAIPUR

Sl. Item Description Quantity Units

Quoted Rate in Figures Select

Estimated Rate TOTAL AMOUNT in TOTAL AMOUNT

You might also like