0% found this document useful (0 votes)
37 views12 pages

NWV 303

When a router has multiple paths to the same destination network from the same routing protocol, it will choose the path with the lowest metric to forward packets. Administrators may choose static routing over dynamic routing for its ease of maintenance in large networks and because it uses less router processing and bandwidth. A router uses its routing table to determine how to forward IP packets.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
37 views12 pages

NWV 303

When a router has multiple paths to the same destination network from the same routing protocol, it will choose the path with the lowest metric to forward packets. Administrators may choose static routing over dynamic routing for its ease of maintenance in large networks and because it uses less router processing and bandwidth. A router uses its routing table to determine how to forward IP packets.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 12

13:05 08/03/2024 NWC303 Lab 8 (Routing Concepts)

NWC303 Lab 8 (Routing Concepts)


Routing Concepts

[email protected] Switch accounts

* Indicates required question

Email *

Record [email protected] as the email to be included with my response

When a router learns that multiple paths are available to a destination * 1 point

network from the same routing protocol, which factor is considered by a


router to choose the best path to forward a packet?

the fastest bandwidth of exiting interfaces

the lowest metric

the order of paths on the routing table

the reliability value of the neighboring routers

https://docs.google.com/forms/d/e/1FAIpQLScOsIPT7J98YWuPbez3Odml-QCrWoclPFO6xBjKzhqBBRvK3A/viewform 1/12
13:05 08/03/2024 NWC303 Lab 8 (Routing Concepts)

What are two reasons why an administrator might choose to use static * 1 point
routing rather than dynamic routing? (Choose two.)

Static routing is more scalable

Static routing uses less router processing and bandwidth

Static routing is easier to maintain in large networks

Static routing is more secure

Static routing does not require complete knowledge of the whole network

Which route entry would be used for a packet with a destination IP address * 1 point
that matches an IP address of one of the router interfaces?

depends on the source of the route

L for Local

C for Directly Connected

S for Static

Which type of static route creates a gateway of last resort? * 1 point

standard static route

summary static route

default static route

floating static route

https://docs.google.com/forms/d/e/1FAIpQLScOsIPT7J98YWuPbez3Odml-QCrWoclPFO6xBjKzhqBBRvK3A/viewform 2/12
13:05 08/03/2024 NWC303 Lab 8 (Routing Concepts)

If a router needs to send an ARP Request for the IPv4 address in one of its * 1 point
route entries, this means the packet will be forwarded:

Which packet forwarding method is used by default on Cisco routers?

To the device with the destination IPv4 address of the packet

What is an advantage of using dynamic routing protocols instead of static * 1 point


routing?

easier to implement

fewer router resource overhead requirements

more secure in controlling routing updates

ability to actively search for new routes if the current path becomes unavailable

If a router needs to send an ARP Request for the destination IPv4 address * 1 point
of the packet, this means the packet will be forwarded:

To a next-hop router

To the device with the destination IPv4 address of the packet

What is used to determine the minimum number of far-left bits that must * 1 point
match between the prefix in the route entry and the destination IP address.

the classful address of the network address

prefix length in the routing table entry

prefix length of the destination IP address

https://docs.google.com/forms/d/e/1FAIpQLScOsIPT7J98YWuPbez3Odml-QCrWoclPFO6xBjKzhqBBRvK3A/viewform 3/12
13:05 08/03/2024 NWC303 Lab 8 (Routing Concepts)

What are two functions of a router? (Choose two.) * 1 point

It builds a routing table based on ARP requests

It controls the flow of data via the use of Layer 2 addresses

It determines the best path to send packets

A router connects multiple IP networks

It provides segmentation at Layer 2

What are two functions of dynamic routing protocols? (Choose two.) * 1 point

to maintain routing tables

to avoid exposing network information

to assure low router overhead

to choose the path that is specified by the administrator

to discover the network

What table does a router use to determine how to forward an IP packet? * 1 point

neighbor cache

routing table

ARP table

MAC address table

https://docs.google.com/forms/d/e/1FAIpQLScOsIPT7J98YWuPbez3Odml-QCrWoclPFO6xBjKzhqBBRvK3A/viewform 4/12
13:05 08/03/2024 NWC303 Lab 8 (Routing Concepts)

What type of network is accessed by a single route and the router has only * 1 point
one neighbor?

Next-hop network

Directly connected network

Local network

Stub network

Which value represents the "trustworthiness" of a route and is used to * 1 point


determine which route to install into the routing table when there are
multiple routes toward the same destination?

administrative distance

routing protocol

outgoging interface

metric

True or False? A default route can only be a static route. * 1 point

True

False

https://docs.google.com/forms/d/e/1FAIpQLScOsIPT7J98YWuPbez3Odml-QCrWoclPFO6xBjKzhqBBRvK3A/viewform 5/12
13:05 08/03/2024 NWC303 Lab 8 (Routing Concepts)

The output of the show ip route command contains the following entry: * 1 point
S 10.2.0.0 [1/0] via 172.16.2.2.

What value is indicated by the 1 in the [1/0] portion of the output?

metric

number of hops

administrative distance

interface ID through which the network can be reached

Which two route source codes are automatically created within a routing * 1 point

table whenever a router interface is configured with an IP address and


activated? (Choose two.)

Which two route sources have the ability to automatically discover a new * 1 point
best path when there is a change in the topology? (Choose two.)

Default route

Static route

OSPF

EIGRP

https://docs.google.com/forms/d/e/1FAIpQLScOsIPT7J98YWuPbez3Odml-QCrWoclPFO6xBjKzhqBBRvK3A/viewform 6/12
13:05 08/03/2024 NWC303 Lab 8 (Routing Concepts)

Which feature on a Cisco router permits the forwarding of traffic for which * 1 point
there is no specific route?

outgoing interface

gateway of last resort

route source

next-hop

Which three advantages are provided by static routing? (Choose three.) * 1 point

Static routing typically uses less network bandwidth and fewer CPU operations than
dynamic routing does

Configuration of static routes is error-free

No intervention is required to maintain changing route information

The path a static route uses to send data is known

Static routes scale well as the network grows

What are two common types of static routes in routing tables? (Choose * 1 point
two)

a built-in static route by IOS

a static route converted from a route that is learned through a dynamic routing
protocol

a static route to a specific network

a default static route

a static route shared between two neighboring routers

https://docs.google.com/forms/d/e/1FAIpQLScOsIPT7J98YWuPbez3Odml-QCrWoclPFO6xBjKzhqBBRvK3A/viewform 7/12
13:05 08/03/2024 NWC303 Lab 8 (Routing Concepts)

What address and prefix length is used when configuring an IPv6 default * 1 point
static route?

FF02::1/8

::/0

::1/128

0.0.0.0/0

Which routing table principle is not correct? * 1 point

Every router makes its decision alone, based on the information it has in its own
routing table

The fact that one router has certain information in its routing table does not mean
that other routers have the same information

Routing information about a path from one network to another also provides routing
information about the reverse, or return, path

What term is used to describe routing over two or more paths to a * 1 point

destination with equal cost metrics?

equal cost routing

equal packet forward

equal cost load balancing

equal path selection

https://docs.google.com/forms/d/e/1FAIpQLScOsIPT7J98YWuPbez3Odml-QCrWoclPFO6xBjKzhqBBRvK3A/viewform 8/12
13:05 08/03/2024 NWC303 Lab 8 (Routing Concepts)

What metric is used by OSPF to determine the best path? * 1 point

decided by the network administrator

hop count

bandwidth and delay

cost

What type of routing is typically used with a stub network? * 1 point

static routes

dynamic routing protocols

Which packet-forwarding method does a router use to make switching * 1 point

decisions when it is using a forwarding information base and an adjacency


table?

process switching

flow process

fast switching

Cisco Express Forwarding

https://docs.google.com/forms/d/e/1FAIpQLScOsIPT7J98YWuPbez3Odml-QCrWoclPFO6xBjKzhqBBRvK3A/viewform 9/12
13:05 08/03/2024 NWC303 Lab 8 (Routing Concepts)

A network administrator configures a static route for the same destination * 1 point
network that was learned automatically by the router using OSPF. Which
route will be installed and why?

Static route because it has a lower metric

OSPF route because it has a lower administrative distance

Static route because it has a lower administrative distance

OSPF route because it has a lower metric

Which type of routing automatically adapts to topology changes? * 1 point

static routes

both static routes and dynamic routing protocols

dynamic routing protocols

What action will a router take on a packet with a destination IP address that * 1 point
is on a remote network?

It will forward the packet directly to the device with the destination IP address of the
packet

It will forward the packet to a next-hop router

It will drop the packet

It will forward the packet to an Ethernet switch

https://docs.google.com/forms/d/e/1FAIpQLScOsIPT7J98YWuPbez3Odml-QCrWoclPFO6xBjKzhqBBRvK3A/viewform 10/12
13:05 08/03/2024 NWC303 Lab 8 (Routing Concepts)

Which packet forwarding method is used by default on Cisco routers? * 1 point

Ethernet switching

Cisco Express Forwarding

process switching

fast switching

Which of the following routes may be found in a routing table? (Choose all * 1 point
that apply.)

static routes

default route

directly connected networks

dynamic routing protocol routes

Which type of route would typically be used on a border router so that * 1 point
devices inside the company could access the Internet?

default

summary

static

directly connected

Submit Page 1 of 1 Clear form

This form was created inside FPT University. Report Abuse

Forms

https://docs.google.com/forms/d/e/1FAIpQLScOsIPT7J98YWuPbez3Odml-QCrWoclPFO6xBjKzhqBBRvK3A/viewform 11/12
13:05 08/03/2024 NWC303 Lab 8 (Routing Concepts)

https://docs.google.com/forms/d/e/1FAIpQLScOsIPT7J98YWuPbez3Odml-QCrWoclPFO6xBjKzhqBBRvK3A/viewform 12/12

You might also like