Scribd Logo
Upload

Welcome to Scribd!

  • 62 views

    Anchor Bolt Design

    Uploaded by

    Nadir Khattak Jr.
    The document provides an anchor bolt design report for supporting a pipe. It analyzes various load cases and performs checks for bearing pressure on concrete, tension in bolts, shear in bolts, combined shear and tension, embedded bolt length, and weld capacity. The checks determine the bearing pressure on concrete, tension in bolts along the Z direction, shear in bolts, combined shear and tension, and embedded bolt length are unsafe. The thickness of the base plate, tension in bolts along the X direction, and weld capacity are determined to be safe.

    Copyright:

    © All Rights Reserved
    Download as XLSX, PDF, TXT or read online from Scribd

    Anchor Bolt Design

    Uploaded by

    Nadir Khattak Jr.
    62 views8 pages
    The document provides an anchor bolt design report for supporting a pipe. It analyzes various load cases and performs checks for bearing pressure on concrete, tension in bolts, shear in bolts, combined shear and tension, embedded bolt length, and weld capacity. The checks determine the bearing pressure on concrete, tension in bolts along the Z direction, shear in bolts, combined shear and tension, and embedded bolt length are unsafe. The thickness of the base plate, tension in bolts along the X direction, and weld capacity are determined to be safe.

    Original Title

    Anchor bolt Design

    Copyright

    © © All Rights Reserved

    Available Formats

    XLSX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides an anchor bolt design report for supporting a pipe. It analyzes various load cases and performs checks for bearing pressure on concrete, tension in bolts, shear in bolts, combined shear and tension, embedded bolt length, and weld capacity. The checks determine the bearing pressure on concrete, tension in bolts along the Z direction, shear in bolts, combined shear and tension, and embedded bolt length are unsafe. The thickness of the base plate, tension in bolts along the X direction, and weld capacity are determined to be safe.

    Copyright:

    © All Rights Reserved
    Download as XLSX, PDF, TXT or read online from Scribd
    Download as xlsx, pdf, or txt
    62 views8 pages

    Anchor Bolt Design

    Uploaded by

    Nadir Khattak Jr.
    The document provides an anchor bolt design report for supporting a pipe. It analyzes various load cases and performs checks for bearing pressure on concrete, tension in bolts, shear in bolts, combined shear and tension, embedded bolt length, and weld capacity. The checks determine the bearing pressure on concrete, tension in bolts along the Z direction, shear in bolts, combined shear and tension, and embedded bolt length are unsafe. The thickness of the base plate, tension in bolts along the X direction, and weld capacity are determined to be safe.

    Copyright:

    © All Rights Reserved
    Download as XLSX, PDF, TXT or read online from Scribd
    Download as xlsx, pdf, or txt
    of 8

    TITLE:Anchor bolt design start of staircase

    JOB NO. 23021


    Made by Nadir DOC NO. AB140–SD-DD-004
    ANCHOR BOLTS DESIGN REPORT SHEET NO. Page 200 of 205
    REV NO. 0

    BASE PLATE & ANCHOR BOLT DESIGN FOR SUPPORT TYPE 02B( PIPE 168.3)

    LOADING DETAILS
    Considering three critical loading combinations from STAAD
    Case (i) : Max. vertical load and corresponding shear & moments
    Case (ii) : Max. moment and correspong force & shear
    Case (i) : Min. vertical load (or) Max.tension and correspondng shear & moments

    FY Fx kN Fz kN Mx Mz
    kN kNm kNm
    Case (i) -63 42 -4 66 353
    Case (ii) 12 25 5 12
    Case (iii) 12 25 5 12

    SECTION DETAILS
    Assumed Section = PIPE 508
    Depth D = 450 mm
    Width B = 450 mm

    BASE PLATE DETAILS


    Length Lp = 400 mm
    Width Bp = 400 mm
    Thickness Tp = 32 mm
    Strength of plate pyp 275 N/mm2

    ANCHOR BOLT DETAILS


    Type of bolt = M24
    Anchor bolt dia ø = 24 mm
    Number of bolts n = 10
    Tensile area of bolt At = 361.9 mm2
    Tension capacity of bolt Pnom = 88.6 kN
    Shear capacity of bolt Ps = 11.07 kN
    Edge distance provided e = 50 mm
    Embedded length of bolt La = 750 mm
    TITLE:Anchor bolt design start of staircase
    JOB NO. 23021
    Made by Nadir DOC NO. AB140–SD-DD-004
    ANCHOR BOLTS DESIGN REPORT SHEET NO. Page 200 of 205
    REV NO. 0
    CONCRETE DETAILS
    Grade of concrete = C40
    Characteristic compressive strength fcu = 40 N/mm2
    Bond coefficient β = 0.3 (BS8110:1997 Table 3.26)
    Permissible bearing pressure on conrete wp = 06*fcu
    = 24 N/mm2

    CHECK FOR BEARING PRESSURE ON CONCRETE


    Maximum pressure on concrete = (P/A)+(Mx/Zx)+(Mz/Zz)
    = 38.8875 N/mm2
    > wp UNSAFE

    CHECK FOR THICKNESS OF BASE PLATE


    Maximum base pressure wp = 38.8875 N/mm2
    By assuming constant pressure max. BM = 4.8609375 kNm
    Assumed thickness of base plate Tp = 32 mm
    Plate modulus Z = 68267 mm3
    Moment capacity Mc = 1.5*pyp*z
    = 28.2 kNm
    > Max. BM SAFE

    CHECK FOR TENSION IN BOLTS


    Moment causing tension on bolts along Z directio = 153 kNm
    Lever arm = 150 mm
    Direct tension on bolts = 8 kN
    Number of bolts in tension side = 7
    Push pull force = 1020 kN
    Total tension on each bolts = 146.51428571429 kN
    > Pnom UNSAFE

    Moment causing tension on bolts along X directio = 66.00 kNm


    Lever arm = 150 mm
    Direct tension on bolts = 12 kN
    Number of bolts in tension side = 7
    Push pull force = 440 kN
    Total tension on each bolts = 64.057142857143
    < Pnom SAFE

    CHECK FOR SHEAR IN BOLTS


    Resultant shear Fs = 42.190046219458 kN
    Shear on each bolts = 21.095023109729 kN
    > Ps UNSAFE

    CHECK FOR COMBINED SHEAR AND TENSION

    (Fs/Ps) + (Ft/Pnom) < 1.4 (BS5950:2000 Cl. 6.3.4.4)


    = 3.56
    > 1.4 UNSAFE
    TITLE:Anchor bolt design start of staircase
    JOB NO. 23021
    Made by Nadir DOC NO. AB140–SD-DD-004
    ANCHOR BOLTS DESIGN REPORT SHEET NO. Page 200 of 205
    REV NO. 0
    TITLE:Anchor bolt design start of staircase
    JOB NO. 23021
    Made by Nadir DOC NO. AB140–SD-DD-004
    ANCHOR BOLTS DESIGN REPORT SHEET NO. Page 200 of 205
    REV NO. 0
    CHECK FOR EMBEDDED LENGTH OF ANCHOR BOLT
    Design ultimate ahcnorage bond stress fbu = β(fcu)^1/2 (BS8110:1997 Cl. 3.12.8.4)
    = 1.897366596101
    Maximum tension on each bolts Ft = 146.51428571429 kN
    Embedded length required Lreq = Ft/(fbu*PI()*ø)
    = 1024.1595225072 mm
    Provided embedded length of bolt La = 750 mm
    < Lreq UNSAFE
    CHECK FOR WELD BETWEEN SECTION & BASE PLATE
    Available length of weld Lw = 508 mm
    Design strength of weld pw = 220 N/mm2
    Size of weld s = 6 mm
    Shear capacity of weld Sw = 0.7*s*pw*Lw
    = 469.392 kN
    Actual shear force on weld Fs = 42.190046219458 kN
    < Sw SAFE

    You might also like