R

Outdoor Wireless Solar Camera

Model: S60 Pro

 Warranty Ser vice

Thanks for purchasing from Soliom.

Having issues with your Soliom cameras?

Please contact us through either ways below.
Soliom care team staffs would offer you a best
solution to solve any problems within 24 hours .

Register via below link to get 3 Years Extended

Warranty .
https://soliom.net/pages/product-registration

Contact Us:
: [email protected]
：+8613377779773
：https://www.facebook .com/soliomcam

If this manual is not clear enough to

read,please download a PDF file via
below link :
https://soliom.net/pages/download
 5-12
13-16
17-24
Par t 5: How to save and delete videos.....................25
Par t 6: FQAs.............................................................26
Warm tips before you go:
1. Soliom S60 Pro can only be set up with 2.4g Wi-Fi network. (It's ok
to use Cell phone 4G data to live viewing it after the camera was
set up with 2.4g Wi-Fi network firstly.)
2. You may possibly need a Wi-Fi extender if your Wi-Fi signal is
weak around the yard where you want to install it.
3. At least 1-3 hours direct sunlight to the camera every day is
needed, the more sunshine the better to avoid manually charge
it frequently. (North side of the house is not a recommended
installation place)
4. Please format the micro sd card to FAT32 format and install the
card when camera powered off.(Micro sd card is not provided
in the package)
5. Please charge your Soliom camera before you set it up, it
usually takes up to 6-8 hours to fully charge it.Do not use any
power adaptor exceed 5V/2A,or it may damage the camera.
(There's no indicator to show charging status from the camera)
6. Make sure the distance between your phone,router and the
camera is no more than 1.5 feet when you're ready to pair the
camera. Ensure that the Wi-fi signal strength on your phone is
good.
7. The PIR range is 15 feet around,the recommend camera install
height is 8 feet around.To avoid too much false alarms, we
suggest you do not install the camera with nearby bushes,shrubs,
grasses and tree leaves coming into the PIR range.
8. To ensure an accurate motion detection funtion,it is suggested
to adjust the camera angle physically to focus the motion area
within the PIR suggested 8-15ft range.
9. If you install the camera on stucco,brick or concrete surface,please
mark 3 holes matching the bracket and then use a drill driver to
drill into the wall and insert the expansion screws to hold the
camera tightly
 Solar Panel

Bracket

Silica gel cover

USB

Power Button
Before Installation

Charging
Please charge the camera about 6-8 hours by plugging it
into a power source using the provided USB cable. After
connecting the camera with App, the App will indicate the
batter y status. (There's no indicator to show charging status
from the camera)

Inser t SD card
Please format the SD card to FAT32 format (Application to
Windows system ONLY), then install the micro-SD card when
the camera is off. The camera only supports class 10 SD cards
with at least an 8GB capacity and a maximum capacity of 64GB

SD Card

3
Before Installation

Pa c k a g e C o n t e n t

Camera 1 x Bracket 3 x Expansion Screws

2 x Extra Machine 1 x USB Cable 1 x Reset Pin

Screws

Outdoor Wireless Solar Camera

Model: S70

1 x User Manual

4
In-App Setup

Make sure the distance between your phone,router

and the camera is no more than 1.5 feet when you're
ready to pair the camera.Ensure that the Wi-fi signal
strength on your phone is good.

1. Download the App (works only with iOS & Android devices)
Please locate the“SOLIOM” in your Google Play store or App store
to download the soliom App.

2. Turn on the camera

Press the power button to turn on the camera, after 3
seconds, LED flashes blue. Then you will hear the following
voice “ The camera is now ready to begin pairing”.

Flashes blue

5
In-App Setup

3. Pairing the camera with the App

Please connect your phone to the 2.4Ghz wifi firstly
before you pair the camera, make sure your router
password in mind before you star t the pairing process.
1) Click "Add a device" and then choose "Setup device",
click "Yes", when you hear the following voice “ The
camera is now ready to begin pairing”.

2) Input the CORRECT WiFi password of your router, if you input

a wrong password you will not be able to connect it successfully.
Click the eye icon to double confirm the password you entered
correct

Your own wifi name

Click the icon to double
confirm the password you
entered correct

6
In-App Setup

3) Enter into the “search device” page, make sure to turn up

you phone’s volume to the Maximum, you will hear the
following voice : “Pairing Information Received”.

What should you do if you can not add the

camera to the APP successfully?
1. Reboot your router to make sure the WiFi network smooth.
2. Reset the camera using the pin included.
3. Turn up your phone’s volume to the Maximum.
4. Re-do the In-App setup as per user manual page 5 to 7.
5. Please confirm again your WiFi password correct.
6. Please make sure your router setting is DHCP enabled,
otherwise your router will not send out WiFi signal for
any wireless device for pairing up.

4) You have connected the device to the App successfully.

Now you can setup a password to log in, which could
protect your privacy. The camera password should be
more than 8 characters in length including numbers
and letters.

Please choose " Non chinese

mainland users” or you will
not get proper notifications
from the correct ser ver

7
In-App Setup

5) Congratulations! Now you can live view the camera on

your phone anytime and anywhere.

8
In-App Setup

If you're unable to pair the camera,Please check below

suggestions:

1. Please reset the camera using the pin to reset the camera to
default after you fully charged the camera.
2. Please turn up your phone volume to the maximum,since the
camera pair through sound wave.
3. Please put the camera,phone as near as to your router (within
1.5 feet) to get a strong wifi signal strength.
4. Please click on the eye icon when you input your router wifi
password to make sure your wifi password CORRECT.
5. Please make sure your router setting is DHCP enabled, otherwise
your router will not send out WiFi signal for any wireless device for
pairing up.

How to reset camera:

Press and hold on the reset button with included reset pin for 4-5
seconds to reset the device.You need to release the button when
you hear the voice"Di", then you will hear "system reset". If you press
longer, the device will be turned off.

9
In-App Setup
4. How to Share Your Camera And Password
with More Users
Share QR code
After you finish the connection with the App, click and
choose “Share QR code” .

Other users need to download the App first, and then scan
the below QR code.

Note:
1. Your camera password can be seen by the invited users,but
they can not modify it.
2. The invited users can change all the camera settings,so the
camera will work as per the last change made on the settings
among all users.
3. If your camera does not work as you set before,please check
the settings from the invited users’ device.
10
In-App Setup
Push Mode

1 Silence: You could choose to mute all incoming

notification or call in, all motion triggered videos will
be saved properly to cloud storage or Micro sd card.
2 Notification: Camera will receive notification and
banner.
3 Call in: Camera will receive call in sound and banners
the same time with a “ Dingdong” sound.

Cloud storage
You can play back all cloud videos here. Cloud video length
is 8 seconds defaulted and 20 free video clips per day. The
oldest footages will be over written by the newest one day
by day.
Check Calendar for video histor y

Download video to your phone

Delete all Cloud videos Delete current video

11
In-App Setup

Micro sd card Video playback

Please find the orange color for the video event and use two
fingers to zoom out the timeline and then put the line to the
head of the orange color and wait for the playback

Zoom out to playback

12
Physical Installation
1 Check your camera signal strength

Check in App If not satisfied with video smoothness,

and signal strength in App is not strong,
we would suggest adding wifi extender
between the Router and the camera.
Camera

WiFi extender Router

2 Recommended height to install the camera

We suggest installing the camera about 8ft.
You may adjust the camera angle physically
according to the live view in your mobile.
to focus your motion area to get the more
accurate motion triggered events.
)
H igh
vit y(
siti t
Sen fee
PIR 15 8 feet

If your camera get numerous motion aler ts unexpected

1) Please adjust your camera installation angle a bit down to
focus the motion area.
2) Please change your PIR sensitivity to Low to reduce the PIR
sensitivity.
3) Do not install the camera with nearby bushes,shrubs,
grasses and tree leaves coming into the PIR range.

Adjust camera angle

)
ow
(L
y
it
iv

et
it
ns

fe
Se

8
R
PI

13
Physical Installation
4 Adjust the bracket on the wall and then mark 3 holes for
mounting. Fix the bracket to the wall by expansion screws.

Adjustable

（Option for indoor use)

14
Technical Specifications

Image Quality Resolution 1080P

Specifications Lens angle
Lens
FOV 160°

Video format H.264

Video Frames per

15fps
Specifications second
SD card
8GB-Max 64GB
support

Output Built-in speaker

Audio
Intput Built-in microphone

Communications WiFi 2.4GHz

Battery capacity 4000mAh

Battery Standby time Max 6 months

Power 2W(run)/
consumption 0.012W (standby)

Temperature -20℃~+60℃(-4 F-140 F)

Applicable
Environment Humidity 20%~85%
(Non-condensing)

15
Technical Specifications

System
Android 2.3 above/ iOS 7.0 above
Suppport
PIR angle 110°
PIR
PIR range 13ft-15ft
Night Vision Range Up to 32ft
Continuously daytime
Max 12 hours
recording time
Working time for
fully charged Continuously night vision
Max 8 hours
recording time
Waterproof IP grade IP66

LED Status
LED flashes green once and goes
Turn on the camera
off and LED flashes blue
Connect network successfully LED stays blue
PIR was triggered LED flashes green once and goes
off and LED stays blue
Camera working LED stays blue
Standby mode LED goes off

16
Detailed App Instructions

1.click ,you could live viewing videos.

Impor tant:
Please keep the Cloud Storage turned on to
ensure the camera's time kept synchronized
with your phone's time.

17
Detailed App Instructions
Battery charging sign
When camera exposed to sunlight,the battery will
keep charging in green.

During night or fully charged,the battery will

stay white.
Tips : If your battery sign will not show correct
status as above,please remove the solar panel
Wifi signal strength and then re install it to the camera body.Or
Tips: Please make sure your camera contact Soliom support team for a replacement
has a full bar of wifi strength to at [email protected] All friendly customer
ensure a smooth live view speed. service staffs are ready to assist you.
(A wifi extender is recommended
to install beside the camera if needed) Low power indicator,please recharge the camera
manually using the provided USB cable

Click here to chose the resolution to HD

(1080P) OR SD(720P)

Number of users
Tips: If you have invited a second users to visit
your camera.Please pay attention to below
points:
1.Your camera password can be seen by the
invited users,but it can not be modified.
2.The invited users can change all the camera
settings,so the camera will work as per the
last change made on the settings among all
users.
3.If your camera does not work as you set
before,please check the settings from the
invited users' device.

18
Detailed App Instructions

Screenshot: Click to screen capture

and pictures will be saved to your phone's
album.

Manual Recording: Click to manually

record and the videos will be saved to
your phone's Album

Setting: Click to inter into device

settings. ( Check page 19 for more
details)

Voice: Click to mute the sounds from

the camera.

Cruise: Click to live view the camera automatically by clicking

on Switch button or double click on screen to enlarge it to a full
screen mode .

Cloud storage: Click to playback videos saved in cloud storage.

Album: View your screen shot pictures or manual record videos

here.

19
Detailed App Instructions

SD Card Setting
1) Please turn on the cloud storage so that you can sync the
camera time with your phone.
2) Please format the micro sd card before you installed it.The camera
doesn't support plug and play.So please make sure to power off
the camera and then install your card.

Album Switch Cruise Voice Settings

Orientation
You can choose Normal Rotate,Mirror or Mirror and rotate
depends on your hardware installation way. The default is
Normal.

Album Switch Cruise Voice Settings

20
Detailed App Instructions

Environment
You can choose to set it as Normal, back light compensation,
night IR, High light compensation or Dynamic according to
your actual light environment of installation place.

Album Switch Cruise Voice Settings

PIR Detection
You can set the PIR sensitivity as Disabled,Low,Medium
and High.
1) When you set the PIR as Disabled,you will not record
and receive any motion triggered events.
2) It is recommended to set the PIR Detection to High so
that you could capture as more as a motion triggered
from the beginning par t of the event.
3) Tr y to capture more the beginning of the triggered
event,please adjust your camera angle a bit closer to your
aimed spot（Check page 13 diagram).

21
Detailed App Instructions

Album Switch Cruise Voice Settings

Dormancy Time
1) This is the time you could set for the video length recorded
to micro sd card.
2) Not dormant: If you choose this option,you will not allow
the camera enter into standby mode,the camera will keep
recording all the time until battery drains out. ( 60 seconds
per file)

Album Switch Cruise Voice Settings

22
Detailed App Instructions
LED Lamp
When you choose Enable,the Blue LED will light up to indicate
when you operate the camera as it should be.When you choose
Disabled,the Blue LED will not light up to indicate the operations
or trigger motions.It is recommended to set it as the default

Album Switch Cruise Voice Settings

Power frequency
Please choose 60 or 50HZ according to your local frequency,
It's defaulted to 60HZ for united states users.

Album Switch Cruise Voice Settings

23
Detailed App Instructions
Device Name and Password:
You can set a desired name for your camera and set the
password to protect your camera's privacy.

Album Switch Cruise Voice Settings

Click “Check for update” to update the app to the newest

version. The newest version app will fix some bugs of the
software we encountered.

Album Switch Cruise Voice Settings

24
How to save and delete videos
1. Videos can be saved in Cloud Storage:
(1). The videos of PIR activity
You could save 20 videos of PIR activities per day in cloud storage,
which can be saved for 7 days and then will be over written.

2. Videos can be saved in the SD card:

(1). The videos of PIR activity
(2). The videos of live viewing
You could playback these videos on the timeline in the App and
format the SD card in the App.

3. Videos can be saved on the mobile phone album:

(1). The videos of REC mode
(2). The screenshot
You need to delete the videos of REC mode and the screenshots
from your phone's album.
25
FA Q s

Q1: Why do I fail to connect the camera to the App by

sound wave?
A: 1. Please reset the camera by the pin included.
2. Please make sure the camera is powered on and
there will be voice prompts that indicates it.
3. Make sure the distance between your mobile phone
and the device is no more than 30cm. And your mobile,
camera and router are in the same room.
4. Adjust your phone volume to maximum.
5. Double check your WiFi password and make sure it is
correct.

Q2: When In-App setup is done, why I could not see the
live streams on my mobile?
A: First, check in App to confirm the wifi signal is strong
enough. If not,we would suggest adding wifi extender in
between.

Q3: Why I cannot receive any alarm after I finished connecting

the camera with the App ?
A:1. Click the in App to confirm you have chose ''Notification''
under the ''Push mode''.
2. Check your mobile settings to allow the notification.

26
 R

Customer Care Email: [email protected]

www.soliom.net
www.facebook.com/soliomcam