Iec 60034 7 2020

IEC 60034-7
®
Edition 3.0 2020-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Rotating electrical machines –

iTeh STANDARD PREVIEW
Part 7: Classification of types of construction, mounting arrangements
(standards.iteh.ai)
and terminal box position (IM Code)
IEC 60034-7:2020
Machines électriques tournantes –
https://standards.iteh.ai/catalog/standards/sist/c60f2f4c-8389-4d98-b345-
Partie 7: Classification des modes de construction, des dispositions
d93081cb3d68/iec-60034-7-2020
de montage et position de la boîte à bornes (Code IM)
IEC 60034-7:2020-10(en-fr)
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2020 IEC, Geneva, Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 11

3, rue de Varembé [email protected]
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC

The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications

The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform Electropedia - www.electropedia.org

The advanced search enables to find IEC publications by a The world's leading online dictionary on electrotechnology,
variety of criteria (reference number, text, technical containing more than 22 000 terminological entries in English
committee,…). It also gives information on projects, replaced and French, with equivalent terms in 16 additional languages.
and withdrawn publications. Also known as the International Electrotechnical Vocabulary
(standards.iteh.ai)
IEC Just Published - webstore.iec.ch/justpublished
(IEV) online.
Stay up to date on all new IEC publications. Just Published IEC Glossary - std.iec.ch/glossary
details all new publications released. Available online IEC and 67 000 electrotechnical terminology entries in English and
60034-7:2020
once a month by email. French extracted from the Terms and Definitions clause of
IEC publications issued since 2002. Some entries have been
d93081cb3d68/iec-60034-7-2020
IEC Customer Service Centre - webstore.iec.ch/csc collected from earlier publications of IEC TC 37, 77, 86 and
If you wish to give us your feedback on this publication or CISPR.
need further assistance, please contact the Customer Service
Centre: [email protected].
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications IEC

Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.
Recherche de publications IEC - Electropedia - www.electropedia.org

webstore.iec.ch/advsearchform Le premier dictionnaire d'électrotechnologie en ligne au
La recherche avancée permet de trouver des publications IEC monde, avec plus de 22 000 articles terminologiques en
en utilisant différents critères (numéro de référence, texte, anglais et en français, ainsi que les termes équivalents dans
comité d’études,…). Elle donne aussi des informations sur les 16 langues additionnelles. Egalement appelé Vocabulaire
projets et les publications remplacées ou retirées. Electrotechnique International (IEV) en ligne.
IEC Just Published - webstore.iec.ch/justpublished Glossaire IEC - std.iec.ch/glossary

Restez informé sur les nouvelles publications IEC. Just 67 000 entrées terminologiques électrotechniques, en anglais
Published détaille les nouvelles publications parues. et en français, extraites des articles Termes et Définitions des
Disponible en ligne et une fois par mois par email. publications IEC parues depuis 2002. Plus certaines entrées
antérieures extraites des publications des CE 37, 77, 86 et
Service Clients - webstore.iec.ch/csc CISPR de l'IEC.
Si vous désirez nous donner des commentaires sur cette
publication ou si vous avez des questions contactez-nous:
[email protected].
IEC 60034-7
®
Edition 3.0 2020-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Rotating electrical machines – iTeh STANDARD PREVIEW

Part 7: Classification of types of construction, mounting arrangements
and terminal box position (IM Code)
(standards.iteh.ai)
IEC 60034-7:2020
Machines électriques tournantes –
Partie 7: Classification des modes de construction, des dispositions
d93081cb3d68/iec-60034-7-2020
de montage et position de la boîte à bornes (Code IM)
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.160.01 ISBN 978-2-8322-8845-0
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission

Marque déposée de la Commission Electrotechnique Internationale
–2– IEC 60034-7:2020 © IEC 2020
CONTENTS
FOREWORD ........................................................................................................................... 4
1 Scope .............................................................................................................................. 6
2 Normative references ...................................................................................................... 6
3 Terms and definitions ...................................................................................................... 6
4 Code I (alpha-numeric designation) ................................................................................. 7
4.1 Designation of machines with horizontal shafts ....................................................... 7
4.2 Designation of machines with vertical shafts ........................................................... 9
4.3 Terminal box location ............................................................................................ 12
5 Code II (all-numeric designation) ................................................................................... 12
5.1 Designation ........................................................................................................... 12
5.2 Significance of the first numeral ............................................................................ 13
5.3 Significance of the fourth numeral ......................................................................... 13
5.4 Significance of the second and third numerals ...................................................... 13
5.5 Terminal box location ............................................................................................ 14
5.6 Examples of designations ..................................................................................... 14
5.7 Inclination or declination of shaft ........................................................................... 14
Annex A (informative) Relationship between Code I and Code II .......................................... 24
Bibliography .......................................................................................................................... 25
(standards.iteh.ai)
Table 1 – Designations for machines with horizontal shafts (IM B...) ....................................... 8
Table 2 – Designations for machines with
IECvertical shafts (IM V...) ......................................... 10
60034-7:2020
Table 3 – Code letter for terminal d93081cb3d68/iec-60034-7-2020
box location ...................................................................... 12
Table 4 – Significance of the first numeral ............................................................................ 13
Table 5 – Significance of the fourth numeral ......................................................................... 13
Table 6 – Significance of second and third numerals for first numeral 1 (Foot-mounted
machines with endshield bearing(s) only) .............................................................................. 15
Table 7 – Significance of second and third numerals for first numeral 2 (Foot-and-
flange-mounted machines with endshield bearing(s) only)..................................................... 16
Table 8 – Significance of second and third numerals for first numeral 3 (Flange-
mounted machines with endshield bearing(s) only with a flange part of an endshield) ........... 17
Table 9 – Significance of second and third numerals for first numeral 4 (Flange-
mounted machines with endshield bearing(s) only with a flange not part of an
endshield, but an integral part of the frame or other component) ........................................... 18
Table 10 – Significance of second and third numerals for first numeral 5 (Machines
without bearings) .................................................................................................................. 19
with endshield bearings and pedestal bearings) .................................................................... 20
with pedestal bearings only) ................................................................................................. 21
Table 13 – Significance of second and third numerals for first numeral 8 (Vertical
machines of construction not covered by first numerals 1 to 4) ............................................. 22
with special mounting arrangements) .................................................................................... 23
Table A.1 – Relationship between Code I and Code II for machines with horizontal
shafts (IM B...) ...................................................................................................................... 24
IEC 60034-7:2020 © IEC 2020 –3–
Table A.2 – Relationship between Code I and Code II for machines with vertical shafts
(IM V...) ................................................................................................................................ 24

(standards.iteh.ai)
IEC 60034-7:2020
d93081cb3d68/iec-60034-7-2020
–4– IEC 60034-7:2020 © IEC 2020
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ROTATING ELECTRICAL MACHINES –
Part 7: Classification of types of construction,

mounting arrangements and terminal box position (IM Code)
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
(standards.iteh.ai)
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
IEC 60034-7:2020
5) IEC itself does not https://standards.iteh.ai/catalog/standards/sist/c60f2f4c-8389-4d98-b345-
provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
d93081cb3d68/iec-60034-7-2020
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60034-7 has been prepared by IEC technical committee 2: Rotating
machinery.
This third edition cancels and replaces the second edition, published in 1992, and its
Amendment 1:2000. It constitutes a technical revision.
The main technical changes with regard to the previous edition are as follows:
5.4 Note on twin motors added.

5.5 Reference to 4.3 instead of duplication of text.
5.7 New subclause on marking of shaft inclination or declination.
IEC 60034-7:2020 © IEC 2020 –5–
The text of this International Standard is based on the following documents:
FDIS Report on voting

2/2010/FDIS 2/2018/RVD
Full information on the voting for the approval of this International Standard can be found in the
report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts in the IEC 60034 series, published under the general title Rotating electrical
machines, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

(standards.iteh.ai)
IEC 60034-7:2020
d93081cb3d68/iec-60034-7-2020
–6– IEC 60034-7:2020 © IEC 2020
ROTATING ELECTRICAL MACHINES –
Part 7: Classification of types of construction,

mounting arrangements and terminal box position (IM Code)
1 Scope
This part of IEC 60034 specifies the IM Code, a classification of types of construction, mounting
arrangements and the terminal box position of rotating electrical machines.
Two systems of classification are provided as follows:
– Code I (see Clause 4): An alpha-numeric designation applicable to machines with end-
shield bearing(s) and only one shaft extension.
– Code II (see Clause 5): An all-numeric designation applicable to a wider range of types
of machines including types covered by Code I.
The type of machine not covered by Code II is fully described in words.

The relationship between Code I and Code II is given in Annex A.
(standards.iteh.ai)
2 Normative references
IEC 60034-7:2020
There are no normative referencesd93081cb3d68/iec-60034-7-2020
in this document.
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/

• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
type of construction
arrangement of machine components with regard to fixings, bearing arrangement and shaft
extension
[SOURCE: IEC 60050-411:1996, 411-43-34]
3.2
mounting arrangement
orientation on site of the machine as the whole with regard to shaft alignment and position of
fixings
[SOURCE: IEC 60050-411:1996, 411-43-35]

IEC 60034-7:2020 © IEC 2020 –7–
3.3
shaft extension
portion of a shaft extending beyond an extreme bearing
Note 1 to entry: The bearing may be on the machine itself or be part of an assembly comprising a machine and (an)
additional bearing(s).
[SOURCE: IEC 60050-411:1996, 411-43-07]
3.4
drive-end of a machine
D-end
that end of the machine which accommodates the shaft end
Note 1 to entry: This is normally the driving end of a motor or the driven end of a generator.
Where for some machines the above definition is inadequate, the D-end is defined as follows:
a) Machine with two shaft extensions of different diameter: the end with the larger shaft diameter;
b) Machine with a cylindrical shaft extension and a conical shaft extension of the same diameter: the end with
cylindrical shaft extension;
c) Machine with other arrangements: according to IEC 60034-8 if applicable; otherwise by agreement.
Note 2 to entry: The outer diameter of a forged-on flange is taken to be the diameter of the shaft extension.
[SOURCE: IEC 60050-411:1996, 411-43-36]
3.5
non-drive end of the machine
N-end
(standards.iteh.ai)
that end of the machine opposite to the IEC
drive end
60034-7:2020
[SOURCE: IEC 60050-411:1996, 411-43-37]
d93081cb3d68/iec-60034-7-2020
4 Code I (alpha-numeric designation)
4.1 Designation of machines with horizontal shafts
In Code I, a machine with a horizontal shaft is designated by the code letters IM (International
Mounting), followed by a space, the letter B, one or two numerals as shown in Table 1 and an
optional letter as shown in 4.3.
–8– IEC 60034-7:2020 © IEC 2020
Table 1 – Designations for machines with horizontal shafts (IM B...)
Type of construction
Number Mounting
Desig-
Sketch of end- arrangement
nation Feet Flange Other details
shields (Horizontal shaft)
bearings
With Mounted by feet,

IM B3 2 – –
feet feet down
Endshield flange at
With Mounted on D-end
IM B5 2 – D-end with access
flange side of flange
to back
Mounted by feet,
With
IM B6 2 – – feet left
feet
(viewed from D-end)

(standards.iteh.ai) Mounted by feet,
With
IM B7 2 – – feet right
feet
IEC 60034-7:2020 (viewed from D-end)
d93081cb3d68/iec-60034-7-2020

IM B8 2 – –
feet feet up
Mounted on end
No endshield or
IM B9 1 – – face
bearing at D-end
of frame at D-end
With Special flange Mounted on D-end

IM B10 2 –
flange at D-end side of flange
Endshield spigot.
With Mounted on D-end
IM B14 2 – No access to back
flange side of flange
Flange at D-end
IEC 60034-7:2020 © IEC 2020 –9–
Number Mounting
Desig-
shields (Horizontal shaft)
bearings
No endshield or Mounted by feet,

bearing at D-end. feet down, with
With
IM B15 1 – Additional mounting addi-tional mounting
feet
provisions on D-end on
of frame end face of frame
With
Mounted by feet,
IM B20 2 raised – –
feet down
feet
Mounted by feet,
With Endshield flange
With feet down, with
IM B25 2 raised at D-end with access
flange addi-tional mounting
feet to back
on flange
3 or 4 pads on
IM B30 iTeh STANDARD PREVIEW
2 – –
endshield(s) or frame
Pad mounted
(standards.iteh.ai)
IEC 60034-7:2020 Mounted by feet,
Endshield spigot feet down, with
With With
IM B34 2 d93081cb3d68/iec-60034-7-2020 No access to back addi-tional mounting
feet flange
Flange at D-end on
D-end side of flange
Mounted by feet,
Endshield flange at feet down, with
With With
IM B35 2 D-end with access addi-tional mounting
feet flange
to back on
D-end side of flange
4.2 Designation of machines with vertical shafts
In Code I, a machine with a vertical shaft is designated by the code letters IM (International
mounting), followed by a space, the letter V, one or two numerals as shown in Table 2 and an
optional letter as shown in 4.3.
– 10 – IEC 60034-7:2020 © IEC 2020
Table 2 – Designations for machines with vertical shafts (IM V...)
Number Mounting
Desig-
shields (Vertical shaft)
bearings
Endshield flange at Mounted on D-end

With
IM V1 2 – D-end with access side of flange,
flange
to back D-end down
Endshield flange at Mounted on N-end

With
IM V2 2 – N-end with access side of flange,
flange
to back D-end up
Endshield flange at Mounted on D-end

With
IM V3 2 – D-end with access side of flange,
flange
to back D-end up

(standards.iteh.ai)
Endshield flange at Mounted on N-end
With
IM V4 2 – 60034-7:2020 N-end with access
IEC side of flange,
flange
to back D-end down
d93081cb3d68/iec-60034-7-2020

IM V5 2 – –
feet D-end down

IM V6 2 – –
feet D-end up
Mounted on end face

No endshield or
IM V8 1 – – of frame at D-end,
bearing at D-end
D-end down
Mounted on end face

No endshield or
IM V9 1 – – of frame at D-end,
bearing at D-end
D-end up
IEC 60034-7:2020 © IEC 2020 – 11 –
Number Mounting
Desig-
bearings
Mounted on D-end
With Special flange
IM V10 2 – side of flange,
flange at D-end
D-end down
Mounted on D-end
With Special flange
IM V14 2 – side of flange,
flange at D-end
D-end up
Endshield flange Mounted by feet, with

With With at D-end with additional mounting on
IM V15 2
feet flange access D-end side of flange,
to back D-end down
iTeh STANDARD PREVIEW Mounted on N-end

With Special flange
IM V16 (standards.iteh.ai)
2 –
flange at D-end
side of flange,
D-end up
IEC 60034-7:2020
d93081cb3d68/iec-60034-7-2020
Mounted by feet, with
Endshield spigot
With With additional mounting on
IM V17 2 no access to back
feet flange D-end side of flange,
Flange at D-end
D-end down
Endshield spigot Mounted on D-end

With
IM V18 2 – no access to back side of flange,
flange
Flange at D-end D-end down
Endshield spigot Mounted on D-end

With
IM V19 2 – No access to back side of flange,
flange
Flange at D-end D-end up
3 or 4 pads on
Pad-mounted
IM V30 2 – – endshield(s) or
D-end down
frame
– 12 – IEC 60034-7:2020 © IEC 2020
Number Mounting
Desig-
bearings
3 or 4 pads on
Pad-mounted,
IM V31 2 endshield(s) or
D-end up
frame
Endshield flange Mounted by feet, with

With With at D-end with additional mounting
IM V35 2
feet flange access on D-end side of flange,
to back D-end up
Mounted by feet, with

Endshield spigot
With With additional mounting
IM V37 2 no access to back
feet flange on D-end side of flange,
Flange at D-end
D-end up

4.3 Terminal box location
(standards.iteh.ai)
When designated, the terminal box position shall be coded with a final letter in accordance with
the following rules: IEC 60034-7:2020
a) machines with feet shall be viewed from the D-end with the feet at 6 o’clock;
d93081cb3d68/iec-60034-7-2020
b) machines with flange only and with drains shall be viewed from the D-end and with the
drains at 6 o’clock;
c) other configurations shall not have a coding.
The coding shall conform to Table 3.
Table 3 – Code letter for terminal box location
Letter designation Terminal box location

R Right 3 o’clock
B Bottom 6 o’clock
L Left 9 o’clock
T Top 12 o’clock
None Unspecified
5 Code II (all-numeric designation)
5.1 Designation
In Code II, a machine is designated by the Code letters IM (International Mounting) followed by
a space and four numerals.
The first, second and third numerals designate aspects of construction (see 5.2 and 5.4).
IEC 60034-7:2020 © IEC 2020 – 13 –
The fourth numeral designates the type of shaft extension (see 5.3).
When used, a letter following the four numerals shall designate the terminal box position,
see 5.5.
5.2 Significance of the first numeral
The significance of the first numeral is given in Table 4.
Table 4 – Significance of the first numeral
Table relevant
First
Significance to the second
numeral
and third numerals
0 Not allocated –
1 Foot-mounted machines with endshield bearing(s) only 5
2 Foot-and-flange-mounted machines with endshield bearing(s) only 6
3 Flange-mounted machines with endshield bearing(s) only, 7
with a flange part of an endshield
4 Flange-mounted machines with endshield bearing(s) only, 8
with a flange not part of an endshield but an integral part
of the frame or other component
5 Machines without bearings 9
6 iTeh STANDARD PREVIEW
Machines with endshield bearing(s) and pedestal bearing(s) 10
7 Machines with pedestal bearing(s) only 11
8
(standards.iteh.ai)
Vertical machines of construction not covered by 12
first numeral 1 to 4
9 IEC 60034-7:2020
Machines with special mounting arrangements 13
d93081cb3d68/iec-60034-7-2020
5.3 Significance of the fourth numeral
The significance of the fourth numeral is given in Table 5.
Table 5 – Significance of the fourth numeral
Fourth
Significance
numeral
0 No shaft extension
1 One cylindrical shaft extension
2 Two cylindrical shaft extensions
3 One conical shaft extension
4 Two conical shaft extensions
5 One flanged shaft extension
6 Two flanged shaft extensions
7 Flanged shaft extension (D-end)
and cylindrical shaft extension (N-end)
8 (Not allocated)
9 Other arrangement
5.4 Significance of the second and third numerals
The significance of the second and third numerals is specified in Table 6 to Table 14 depending
on the first numeral with which they are associated (see Table 4).

Iec 60034 7 2020

Uploaded by

Copyright:

Available Formats

Iec 60034 7 2020

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Iec 60034 7 2020

Uploaded by

Copyright:

Available Formats

IEC 60034-7

Rotating electrical machines –

IEC Central Office Tel.: +41 22 919 02 11

About the IEC

About IEC publications

IEC publications search - webstore.iec.ch/advsearchform Electropedia - www.electropedia.org

A propos des publications IEC

Recherche de publications IEC - Electropedia - www.electropedia.org

IEC Just Published - webstore.iec.ch/justpublished Glossaire IEC - std.iec.ch/glossary

Rotating electrical machines – iTeh STANDARD PREVIEW

ICS 29.160.01 ISBN 978-2-8322-8845-0

® Registered trademark of the International Electrotechnical Commission

iTeh STANDARD PREVIEW

INTERNATIONAL ELECTROTECHNICAL COMMISSION

ROTATING ELECTRICAL MACHINES –

Part 7: Classification of types of construction,

5.4 Note on twin motors added.

The text of this International Standard is based on the following documents:

FDIS Report on voting

iTeh STANDARD PREVIEW

ROTATING ELECTRICAL MACHINES –

Part 7: Classification of types of construction,

Two systems of classification are provided as follows:

The type of machine not covered by Code II is fully described in words.

3 Terms and definitions

• IEC Electropedia: available at http://www.electropedia.org/

[SOURCE: IEC 60050-411:1996, 411-43-34]

[SOURCE: IEC 60050-411:1996, 411-43-35]

[SOURCE: IEC 60050-411:1996, 411-43-07]

[SOURCE: IEC 60050-411:1996, 411-43-36]

4 Code I (alpha-numeric designation)

4.1 Designation of machines with horizontal shafts

Table 1 – Designations for machines with horizontal shafts (IM B...)

With Mounted by feet,

iTeh STANDARD PREVIEW

With Mounted by feet,

With Special flange Mounted on D-end

No endshield or Mounted by feet,

4.2 Designation of machines with vertical shafts

Table 2 – Designations for machines with vertical shafts (IM V...)

Endshield flange at Mounted on D-end

Endshield flange at Mounted on N-end

Endshield flange at Mounted on D-end

iTeh STANDARD PREVIEW

With Mounted by feet,

With Mounted by feet,

Mounted on end face

Mounted on end face

Endshield flange Mounted by feet, with

iTeh STANDARD PREVIEW Mounted on N-end

Endshield spigot Mounted on D-end

Endshield spigot Mounted on D-end

Endshield flange Mounted by feet, with

Mounted by feet, with

iTeh STANDARD PREVIEW

The coding shall conform to Table 3.

Table 3 – Code letter for terminal box location

Letter designation Terminal box location

5 Code II (all-numeric designation)