IOP Conference Series: Earth and Environmental Science

PAPER • OPEN ACCESS

Synthesis of silica from rice husk by sol-gel method

To cite this article: N Setyawan et al 2021 IOP Conf. Ser.: Earth Environ. Sci. 733 012149

View the article online for updates and enhancements.

This content was downloaded from IP address 181.215.12.110 on 05/05/2021 at 02:12

International Conference on Green Agro-industry and Bioeconomy IOP Publishing
IOP Conf. Series: Earth and Environmental Science 733 (2021) 012149 doi:10.1088/1755-1315/733/1/012149

Synthesis of silica from rice husk by sol-gel method

N Setyawan, Hoerudin and S Yuliani

Indonesian Center for Agricultural Postharvest Research and Development
Jl. Tentara Pelajar No.12, Kampus Penelitian Pertanian Cimanggu, Bogor, West Java,
Indonesia
E-mail: [email protected]

Abstract. Rice husk is an abundant and underutilized agricultural by-product in Indonesia. The
silica contained in the waste could be used as a substitute natural silica for various purposes. The
extraction of silica from rice husk (RH) has been done using the sol-gel method without
involving high energy. Extraction was carried out with KOH at concentrations of 7, 10, and 13%
for 90, 120, and 150 minutes. Experimental results showed that the highest extraction yield was
obtained at the extraction process using KOH 7% (average 9.03%). The minimum concentration
of KOH could produce the maximum yield of silica. Characterization by XRD showed that the
silica had the same pattern as that of commercial products and it was categorized as amorphous
silica indicated with the broad peaks at 2θ = 22°. Amorphous silica with high purity was
produced from rice husk by KOH 7 % at 120 min (95.34 %). The process condition resulted in
high reactivity and a high BET surface area. The washing process needs to be intensified to
improve the purity of silica.

1. Introduction
Rice husk (RH) is a by-product of rice milling which amounts to approximately 20% of the weight of
unhulled rice. This amount will be abundant in some countries where rice is a staple food of their
majority population. Hence, the RH needs to be processed to obtain high added-value products and also
to reduce environmental problems due to its presence. In recent years, there have been quite a lot of
studies reported on silica extraction from RH to become a solution to the problem of the abundance of
this agricultural waste.
Some studies have claimed that RH is agricultural biomass that has a high silica content, namely 15
- 60% [1][2][3]. In its application, silica has many uses in various industries such as an anti-caking
agent, beverage purifier, oil refining [4], fertilizer, pharmaceuticals products, detergents, adhesives,
electronic semiconductors, catalysts, absorbents, corrosion inhibitors, and optical materials [1][2][5].
Silica obtained by an extraction process from RH combustion has been reported by some researchers
[2][6][7][8]. Meanwhile, the combustion process to obtain rice husk ash has a negative impact on the
environment due to producing air pollution. On this occasion, we hereby present the information on
silica from ‘fresh’ dried RH without the burning process extracted by a sol-gel method with various
concentrations of alkali solvent and extraction times. It is a technique which involves the simultaneous
hydrolysis and condensation reaction of the metal alkoxide. This method has some advantages such as
low-temperature synthesis and control of reaction kinetics by varying the composition of chemicals.
Content from this work may be used under the terms of the Creative Commons Attribution 3.0 licence. Any further distribution
of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.
Published under licence by IOP Publishing Ltd 1
International Conference on Green Agro-industry and Bioeconomy IOP Publishing
IOP Conf. Series: Earth and Environmental Science 733 (2021) 012149 doi:10.1088/1755-1315/733/1/012149

This study aims to investigate the optimum extraction process to produce high purity silica from RH.
The properties studied include structure properties, SiO2 content, and Brunauer Emmett-Teller (BET)
surface area.

2. Materials and Methods

2.1. Materials
The RH was obtained from PT Jatisari Sri Rejeki rice mill, Jatisari, Karawang, West Java, Indonesia
with a moisture content of 5.75%. KOH and HCl used were reagent grade obtained from Merck.
Distilled water was applied for all extraction and treatment process. Commercial silica was used as a
control.

2.2. Production of silica from rice husk

The preparation of silica was conducted following the procedures that have previously been applied by
Sembiring [9]. RH was washed with hot water to remove contaminants of water-soluble organic matters
present. The washing process was conducted by soaking RH in hot water (temperature 80°C) for 2 hours
and repeated 4 times. RH was then dried at room temperature before the silica extraction process.
The silica from RH was obtained using an alkali extraction method previously reported by Sembiring
et al. [10] with some modifications. 50 g dried RH was mixed with 500 ml of 7, 10, and 13 % KOH
solution in a beaker glass. The mixture was boiled for 90, 120 and 150 min, and then allowed to cool to
room temperature and left for 24 h.
The mixture was filtered to separate the filtrate which contained silica (silica sol). To obtain solid
silica, the sol was acidified by adding 10% HCl solution with constant stirring until the mixture was in
pH 7 and the sol was converted into the gel. The gel was aged for three days and then rinsed repeatedly
with distilled water 7 times to remove the excess acid or until clear sol. The gel was then oven-dried at
110°C for eight hours and then ground into powder using a planetary ball mill. The yield of silica was
investigated to determine the optimum extraction process. It can be calculated by the following equation:
mass of produced silica
Silica extraction yield (%)= ×100 (1)
mass of RH

2.3. Characterization
The samples were examined using scanning electron microscopy (SEM), X-ray diffraction (XRD), X-
ray fluorescence (XRF), and Brunauer-Emmett-Teller (BET) surface area analysis. The SEM analyses
of the silica from RH was conducted on an EVO MA10 (ZEISS, Germany). The X-ray diffraction (XRD)
patterns were obtained using a D8 Advance Discovery X-ray Diffractometer (Bruker, Germany) using
Cu anode, LynxEye detector operated at 2Theta between 5° to 80°. Silica content and metallic impurities
were analysed by an Axios mAX WDXRF X-Ray Fluorescence (XRF) Spectrometer (Malvern
Panalytical, The Netherland). Surface area, pore volume, and pore diameter of the prepared silica
powder was measured using BET surface area analyser (Quantachrome NovaWin, USA).

3. Results and Discussion

3.1. Yield of silica

The yield of silica is shown in Table 1. It varies from 7.60 – 9.75 % and shows no significant difference
between each combination of the concentration of KOH and extraction time investigated. This result
concludes that the minimum concentration of KOH and extraction time can produce the maximum yield
of silica.

2
International Conference on Green Agro-industry and Bioeconomy IOP Publishing
IOP Conf. Series: Earth and Environmental Science 733 (2021) 012149 doi:10.1088/1755-1315/733/1/012149

Table 1. Silica extraction yield.

Extraction time (min)/ Yield* (%)
Concentration of KOH (%)
90 120 150 Means
7 9.05aA 8.30aA 9.75aA 9.03A
10 8.55aA 8.60aA 7.60aA 8.25A
13 8.50aA 8.35aA 8.20aA 8.35A
Means 8.70a 8.41a 8.52a
* Means followed by the same capital letters in a column and lower case letters on the lines do not differ significantly by the Duncan test (p
< 0.05). *Values are means (n=2).

3.2. The structural features and composition of silica powders

XRD pattern of silica powders produced using various concentration of KOH and extraction times are
shown in Figure 1. The XRD pattern of silica powder obtained in this study showed a similar pattern to
that of commercial silica. It was categorized as amorphous silica indicated with the broad peaks at 2θ =
22° [11]. This XRD pattern also showed a similar pattern as reported by Setyawan [12]. Various peaks
appear, show metallic impurities in obtained silica powder. The presence of impurities can be confirmed
by the data shown in Table 2.

Figure 1. XRD pattern of silica powders.

XRF is used in identifying the chemical compositions and purity of silica powders produced from
the RH. Table 2 shows the composition of silica (SiO2) and various metallic impurities. The silica
content of the powders produced from RH were from 81.99 – 95.34 %. The silica that was obtained
using KOH 7% at 120 min showed the maximum reactivity. Therefore, according to the result of Table
2, the above conditions are suitable for the production of high purity silica (95.34%). This content was
almost equal to that of commercial silica (95.37%). Silica was obtained from potassium silicate using
a sol-gel method. Mittal [13] reported that the reaction of SiO2 in RH with alkali solution is as follows:
SiO2 + 2KOH  K2SiO3 + H2O (2)

To obtain solid silica, the sol was acidified by adding 5% HCl solution until the sol was converted
into the gel. This process occurred in pH 7 to obtain silica from potassium silicate by the following
reaction:

K2SiO3 + 2HCl  SiO2 + 2KCl + H2O (3)

3
International Conference on Green Agro-industry and Bioeconomy IOP Publishing
IOP Conf. Series: Earth and Environmental Science 733 (2021) 012149 doi:10.1088/1755-1315/733/1/012149

Table 2. Composition of silica powders.

Concentration of Concentration of Concentration of
Elements KOH 7% KOH 10% KOH 13% Commercial
(%) 90 120 150 90 120 150 90 120 150 silica
min min min min min min min min min
SiO2 94.63 95.34 93.72 94.09 92.57 94.26 94.83 91.03 81.99 95.37
K2O 3.11 2.57 3.83 3.78 4.94 3.72 3.24 5.90 10.85 0.01
Cl 0.77 1.03 1.67 1.52 1.78 1.38 0.93 2.43 6.28 0.07
Al2O3 0.40 0.53 0.31 0.28 0.27 0.27 0.36 0.27 0.34 0.63
ZrO2 0.37 0.03 0.18 0.04 0.05 0.09 0.16 0.04 0.08 0.04
Fe2O3 0.35 0.19 0.11 0.13 0.16 0.12 0.19 0.13 0.10 0.06
MgO 0.12 0.08 NA NA NA NA 0.08 NA 0.13 0.06
Na2O 0.09 0.05 0.07 0.07 0.07 0.06 0.09 0.10 0.12 2.47
CaO 0.06 0.04 0.04 0.02 0.03 0.02 0.02 0.02 0.03 0.02
MnO 0.04 0.02 0.02 0.03 0.04 0.04 0.02 0.04 0.04 0.00
P2O5 0.02 0.04 0.02 0.01 0.01 0.02 NA 0.01 0.01 NA
Values are the composition of silica powder analyzed by XRF (n=1)

3.3. Surface area, pore diameter and pore volume

The surface area, pore diameter and pore volume of silica powder extracted with various concentrations
of KOH at 120 min (selected due to producing high purity SiO2) are given in Table 3. The surface area
of silica produced using KOH 7 and 10% (281.20 m2/g and 153.95 m2/g respectively) were higher than
that of commercial silica. The surface area, pore diameter and pore volume of commercial silica were
143.95 m2/g, 22.7 nm, and 1.63 cm3/g respectively. The surface area of obtained silica from the
extraction process using KOH 7% at 120 min was also higher than that of silica produced from RHA
(274 m2/g) as reported by Yuvakkumar [14].
Table 3 shows increasing the concentration of KOH resulted in reducing surface area and pore
volume and increasing the pore diameter. This phenomenon occurs due to the presence of potassium
and other impurities (Table 2) contained in silica powder.

Table 3. Surface area, pore diameter and pore volume of silica powder.
Samples BET
Concentration of KOH Extraction Surface area Pore diameter Pore volume
(%) time (min) (m2/g) (nm) (cm3/g)
7 120 281.20 4.580 1.58
10 120 153.95 9.70 0.74
13 120 108.46 14.43 0.76
Commercial silica 143.95 22.7 1.63

3.4. Morphology of silica powders

The morphology of silica powders are shown in Figure 2. Figure 2 depicts the SEM morphology of the
nano-silica. It showed that silica appears agglomerate and is not a single particle. However, the single-
particle of silica has spherical shaped with an average particle size of 6 nm as reported by Rafiee [7].

4
International Conference on Green Agro-industry and Bioeconomy IOP Publishing
IOP Conf. Series: Earth and Environmental Science 733 (2021) 012149 doi:10.1088/1755-1315/733/1/012149

A B C

D E F

G H I

CS

Figure 2. Morphology of silica powders extracted with KOH 7% for 90 min (A), 120 min (B), 150
min (C); KOH 10% for 90 min (D), 120 min (E), 150 min (F); KOH 13% for 90 min (G),
120 min (H), 150 min (I); and commersial silica (CS).

4. Conclusions
The silica extraction process was conducted by the sol-gel method using KOH 7% resulted in maximum
yield. Amorphous silica with purity above 95% was produced from rice husk by KOH 7 % at 120 min.
The process condition resulted in high purity amorphous silica with a high BET surface area.

Acknowledgment
The authors appreciate Kirana Sanggrami Sasmitaloka for assisting the work at the laboratory of
ICAPRD. The authors also thank R. Idris Suryadi and Dwi Agriana for conducting sample analysis
using SEM and XRD. We also thank IAARD for budgeting the research.

References
[1] Adam F Chew T S and Andas J, 2011 A simple template-free sol-gel synthesis of spherical
nanosilica from agricultural biomass J. Sol-Gel Sci. Technol. 59, 3 p. 580–583.
[2] Agung G Hanafie M R and Mardina P, 2013 Ekstraksi Silika Abu Sekam Padi dengan Pelarut
KOH (Extraction of Silica from Rice Husk Ash Using KOH Solution) Konversi 2, 1 p. 28-
31 [In Indonesian].
[3] Kalapathy U Proctor a. and Shultz J, 2002 An improved method for production of silica from

5
International Conference on Green Agro-industry and Bioeconomy IOP Publishing
IOP Conf. Series: Earth and Environmental Science 733 (2021) 012149 doi:10.1088/1755-1315/733/1/012149

rice hull ash Bioresour. Technol. 85, 3 p. 285–289.

[4] Chaudhry Q and Castle L, 2011 Food applications of nanotechnologies: An overview of
opportunities and challenges for developing countries Trends Food Sci. Technol. 22, 11 p.
595–603.
[5] Awizar D A Othman N K Jalar A Daud A R Rahman I A and Al-Hardan N H, 2013 Nanosilicate
extraction from rice husk ash as green corrosion inhibitor Int. J. Electrochem. Sci. 8, 2 p.
1759–1769.
[6] Carmona V B Oliveira R M Silva W T L Mattoso L H C and Marconcini J M, 2013 Nanosilica
from rice husk: Extraction and characterization Ind. Crops Prod. 43 p. 291–296.
[7] Rafiee E Shahebrahimi S Feyzi M and Shaterzadeh M, 2012 Optimization of synthesis and
characterization of nanosilica produced from rice husk (a common waste material) Int. Nano
Lett. 2, 1 p. 29.
[8] Suka I G Simanjuntak W Sembiring S and Trisnawati E, 2008 Karakteristik Silika Sekam Padi
Dari Provinsi Lampung Yang Diperoleh Dengan Metode Ekstraksi (Characteristics of Rice
Husk Silica From Lampung Province Obtained By Extraction Method) Mipa 37, 1 47–52 [In
Indonesian].
[9] Sembiring S, 2011 Synthesis and Characterisation of Rice Husk Silica Based Borosilicate
(B2SiO5) Ceramic by Sol-Gel Routes 11, 1 p. 85–89.
[10] Sembiring S Simanjuntak W Manurung P Asmi D and Low I M, 2014 Synthesis and
characterisation of gel-derived mullite precursors from rice husk silica Ceram. Int. 40, 5 p.
7067–7072.
[11] Bakar R A Yahya R and Gan S N, 2016 Production of High Purity Amorphous Silica from Rice
Husk Procedia Chem. 19 p. 189–195.
[12] Setyawan N Hoerudin and Wulanawati A, 2019 Simple extraction of silica nanoparticles from
rice husk using technical grade solvent: Effect of volume and concentration IOP Conf. Ser.
Earth Environ. Sci. 309, 1.
[13] Mittal D, 1997 Silica from ash Resonance 2, 7 p. 64–66.
[14] Yuvakkumar R Elango V Rajendran V and Kannan N, 2014 High-purity nano silica powder from
rice husk using a simple chemical method J. Exp. Nanosci. 9, 3 p. 272–281.