Garmin G3X Touch MM

Garmin G3X Touch
Electronic Flight Instrument System

Part 23 AML STC Maintenance Manual
Contains Instructions for Continued
Airworthiness for STC SA01899WI
190-02472-02 October 2023 Revision 9

© Copyright 2019-2023
Garmin Ltd. or its subsidiaries
All Rights Reserved
Except as expressly provided herein, no part of this manual may be reproduced, copied,
transmitted, disseminated, downloaded or stored in any storage medium, for any purpose
without the express prior written consent of Garmin. Garmin hereby grants permission to
download a single copy of this manual and of any revision to this manual onto a hard drive or
other electronic storage medium to be viewed and to print one copy of this manual or of any
revision hereto, provided that such electronic or printed copy of this manual or revision must
contain the complete text of this copyright notice and provided further that any unauthorized
commercial distribution of this manual or any revision hereto is strictly prohibited.
Garmin International, Inc.
1200 E. 151st Street
Olathe, KS 66062 USA
Telephone: 913-397-8200
www.garmin.com
Garmin (Europe) Ltd.

Liberty House
Bulls Copse Road
Hounsdown Business Park
Southampton, SO40 9RB, UK
Phone: +44 (0) 23 8052 4000
Fax: +44 (0) 23 8052 4004
Garmin Würzburg GmbH

Beethovenstrasse 1a
97080 Würzburg, Germany
Garmin AT, Inc.

2345 Turner Rd., SE
Salem, OR 97302 USA
Telephone: 503.581.8101
Maintenance Manual 190-02472-02

G3X Touch EFIS Part 23 AML STC Revision 9
Page ii
RECORD OF REVISIONS
Revision Revision Date Description
1 03/15/2019 Initial release
2 4/05/2019 Added interface to GPS 175 / GNX 375, limitations for GTS 8XX and
non-Garmin autopilots
3 12/20/2019 Added installation and interface to GTR 20/200B, GMA 245R and GAP
26. Added interface to GNC 355(A), CO detector and wig-wag light
functions.
4 02/12/2020 Added GI 275 Standby, updated GDU configurations, software loading
information, CAN bus troubleshooting, and navigator config tables
5 04/08/2021 New fuel quantity interface and configuration for resistive fuel probes
and other minor changes
6 12/29/2021 Updated for Phase 3 Smart Glide Integration
7 05/31/2022 Added GPT pressure transducers and other minor clarifications and
improvements.
8 04/21/2023 Added interface between G3X and GI275 standby, TCW IBBS, and
configuration updates for new software v9.15 functions
9 10/10/2023 Added GEA 24B and new GMA 245R part numbers, interface to
SureFly TACH2, and other clarifications and improvements.
INFORMATION SUBJECT TO EXPORT CONTROL LAWS
This document may contain information which is subject to the Export Administration Regulations (“EAR”)
issued by the United States Department of Commerce (15 CFR, Chapter VII Subchapter C) and which
may not be exported, released or disclosed to foreign nationals inside or outside the United States
without first obtaining an export license. A violation of the EAR may be subject to a penalty of up to 10
years imprisonment and a fine of up to $1,000,000 under section 2410 of the Export Administration Act of
the 1979. The preceding statement is required to be included on any and all reproductions in whole or in
part of this manual.
The information on this document is subject to change without notice. For updates and supplemental
information regarding the operation of Garmin products visit www.fly.garmin.com.

Page iii
SOFTWARE LICENSE AGREEMENT FOR GARMIN AVIATION PRODUCTS
BY USING THE DEVICE, COMPONENT OR SYSTEM MANUFACTURED OR SOLD BY GARMIN (“THE
GARMIN PRODUCT’), YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF THE
FOLLOWING SOFTWARE LICENSE AGREEMENT. PLEASE READ THIS AGREEMENT CAREFULLY.
Garmin Ltd. and its subsidiaries (“Garmin”) grants you a limited license to use the software embedded in
the Garmin Product (the “Software”) in binary executable form in the normal operation of the Garmin
Product. Title, ownership rights, and intellectual property rights in and to the Software remain with Garmin
and/or its third-party providers. You acknowledge that the Software is the property of Garmin and/or its
third-party providers and is protected under the United States of America copyright laws and international
copyright treaties. You further acknowledge that the structure, organization, and code of the Software are
valuable trade secrets of Garmin and/or its third-party providers. You agree not to reproduce, decompile,
disassemble, modify, reverse assemble, reverse engineer, or reduce to human readable form the
Software or any part thereof or create any derivative works based on the Software. You agree not to
export or re-export the Software to any country in violation of the export control laws of the United States
of America.

Page iv
WARNING, CAUTION, and NOTE DEFINITIONS
WARNING
A warning is used to bring to the installer’s immediate attention not only
damage to the equipment, but personal injury may occur if the instruction is
disregarded.
CAUTION
A caution means damage to equipment is possible if procedural step is not followed.
NOTE
A note provides additional information.
WARNING
This product, its packaging, and its components contain chemicals known to the State of California to
cause cancer, birth defects, or reproductive harm. This Notice is being provided in accordance with
California's Proposition 65. If you have any questions or would like additional information, please refer
to our web site at www.garmin.com/prop65.
WARNING
Perchlorate Material – special handling may apply. Refer to www.dtsc.ca.gov/hazardouswaste/perchlorate.
WARNING
Failure to properly configure the EIS gauges per the POH/AFM and other approved data could result in
serious injury, damage to equipment, or death.
NOTE
All screen shots used in this document are current at the time of publication. Screen shots are intended to
provide visual reference only. All information depicted in screen shots, including software file names,
versions and part numbers, is subject to change and may not be up to date.
NOTE
Ensure no dust or grit accumulates at the bottom of the display glass. The GDU 4X0 display uses
invisible infrared beams for touch detection, this makes it very important to keep the screen clean,
especially along the edges.

Page v
TABLE OF CONTENTS
SECTION ................................................................................................................................. PAGE
1. INTRODUCTION ........................................................................................................................ 1
1.1 Content, Scope, Purpose .................................................................................................... 1
1.2 Organization ........................................................................................................................ 2
1.3 Acronyms & Abbreviations .................................................................................................. 3
1.4 Publications ......................................................................................................................... 5
1.5 Revision and Distribution .................................................................................................... 5
2. SYSTEM DESCRIPTION............................................................................................................ 6
2.1 Equipment Descriptions ...................................................................................................... 8
2.2 G3X Optional Interfaces .................................................................................................... 17
2.3 G3X Touch Architecture Example ..................................................................................... 18
2.4 Electrical Power Distribution ............................................................................................. 22
3. G3X CONTROL & OPERATION .............................................................................................. 23
3.1 GDU 4X0 Softkeys/Features and Control ......................................................................... 23
3.2 Display Modes ................................................................................................................... 24
4. INSTRUCTIONS FOR CONTINUED AIRWORTHINESS ........................................................ 31
4.1 Airworthiness Limitations .................................................................................................. 31
4.2 Servicing Information ........................................................................................................ 32
4.3 Maintenance Intervals ....................................................................................................... 32
4.4 Visual Inspection ............................................................................................................... 35
4.5 Electrical Bonding Test ..................................................................................................... 35
4.6 GSU 25D Earth Magnetic Field Updates .......................................................................... 36
4.7 Special Inspection Requirements ..................................................................................... 36
4.8 Pneumatic Line Drain Check (If installed) ......................................................................... 37
5. TROUBLESHOOTING ............................................................................................................. 38
5.1 General Troubleshooting................................................................................................... 38
5.2 CAN Bus Network Troubleshooting .................................................................................. 39
5.3 GDU 4X0 ........................................................................................................................... 42
5.4 GSU 25D ADAHRS and GMU 11 Magnetometer Troubleshooting .................................. 44
5.5 Engine Indication Troubleshooting .................................................................................... 52
5.6 Traffic Alert Messages ...................................................................................................... 54
5.7 Transponder Alert Messages ............................................................................................ 54
5.8 Loss of Navigation Information (External Navigators) ...................................................... 55
5.9 Garmin GFC 500 Failure Messages ................................................................................. 55
5.10 Loss of Non-Garmin Autopilot Heading and/or Course Datum ......................................... 55
5.11 Miscellaneous Alerts ......................................................................................................... 56
5.12 Aircraft Harness/LRU Connectors ..................................................................................... 56
6. G3X EQUIPMENT REMOVAL & REINSTALLATION ............................................................. 74
6.1 GDU 4X0 ........................................................................................................................... 74
6.2 GSU 25D ADAHRS ........................................................................................................... 77
6.3 GMU 11 Magnetometer..................................................................................................... 79
6.4 GTP 59 Temperature Probe ............................................................................................. 79
6.5 GAD 27 Electronic Adapter Unit ....................................................................................... 80

Page vi
6.6 GEA 24(B) Engine Indicating System ............................................................................... 81
6.7 GAD 29B/29D ARINC 429 Adapter .................................................................................. 88
6.8 GDL 5XR Datalink ............................................................................................................. 89
6.9 GPS Antenna (P/N 011-04036-00 or 011-04036-10) ....................................................... 90
6.10 GTR 20 Remote-Mount VHF COM ................................................................................... 92
6.11 GTR 200B VHF COM Radio ............................................................................................. 93
6.12 GMA 245R w/Marker Beacon Audio Panel ....................................................................... 93
6.13 GAP 26 AOA Probe .......................................................................................................... 94
6.14 EIS Annunciator Lights...................................................................................................... 96
7. G3X EQUIPMENT CONFIGURATION & TESTING ................................................................ 98
7.1 GDU 4X0 ........................................................................................................................... 98
7.2 GSU 25D ADAHRS and GMU 11 Magnetometer ............................................................. 98
7.3 GMU 11 Magnetometer................................................................................................... 106
7.4 GTP 59 Temperature Probe ........................................................................................... 106
7.5 GAD 27............................................................................................................................ 106
7.6 GEA 24(B) Engine and Airframe Unit ............................................................................. 107
7.7 GAD 29B/29D ................................................................................................................. 107
7.8 GDL 5XR ......................................................................................................................... 107
7.9 GTR 20 Remote-Mount VHF COM ................................................................................. 108
7.10 GTR 200B VHF COM...................................................................................................... 108
7.11 GMA 245R Audio Panel .................................................................................................. 108
7.12 GAP 26 AOA Probe ........................................................................................................ 108
7.13 G3X Software Information ............................................................................................... 109
7.14 Activation of GDL 51R/52R SiriusXM Radio and Weather ............................................. 114
8. SYSTEM RETURN TO SERVICE PROCEDURE .................................................................. 115
8.1 Recommended Test Equipment ..................................................................................... 115
8.2 Transponder Check......................................................................................................... 116
8.3 GPS Receiver Check ...................................................................................................... 116
8.4 NAV Receiver Check ...................................................................................................... 118
8.5 Audio Panel Interface Check .......................................................................................... 119
8.6 ADS-B Traffic Interface Check ........................................................................................ 121
8.7 TIS-A Traffic Interface Check .......................................................................................... 121
8.8 WX-500 Stormscope Interface Check ............................................................................. 122
8.9 FIS-B Weather via ADS-B In ........................................................................................... 122
8.10 GDL 51R/52R SXM Weather Check ............................................................................... 123
8.11 GDL 51R/52R SXM Audio Interface Check .................................................................... 123
8.12 EIS Check ....................................................................................................................... 123
8.13 ADAHRS and Magnetometer Ground Checks ................................................................ 126
8.14 GTR 20/200B Ground Checks ........................................................................................ 128
8.15 Garmin GFC 500 Autopilot .............................................................................................. 130
8.16 Non-Garmin Autopilot Interface ...................................................................................... 130
8.17 G5 Miscompare Check.................................................................................................... 133
8.18 GI 275 Miscompare Check ............................................................................................. 133
8.19 GAP 26 AOA Probe Checks ........................................................................................... 134

Page vii
8.20 Wig-Wag Landing/Taxi Light Check (if configured) ........................................................ 135
8.21 CO Detector Display Check (if configured) ..................................................................... 135
8.22 Weight and Balance (W&B) Update (as required) .......................................................... 135
8.23 EMI / RFI Check .............................................................................................................. 136
APPENDIX A INSTALLATION SPECIFIC INFORMATION ....................................... A-1
A.1 Maintenance Records ..................................................................................................... A-1
A.2 Equipment Locations....................................................................................................... A-3
A.3 Wire Routing ................................................................................................................... A-3
A.4 Configuration File ............................................................................................................ A-5
APPENDIX B EXTERNAL INTERFACE CONFIGURATION ..................................... B-1
B.1 GPS/VHF Nav Interfaces ................................................................................................ B-1
B.2 GPS NAV Interface ......................................................................................................... B-5
B.3 VHF NAV/COM Interface ................................................................................................ B-7
B.4 Traffic and Weather Source ............................................................................................ B-8
B.5 Non-Garmin Autopilot Systems ..................................................................................... B-11
B.6 Audio Panel ................................................................................................................... B-14
B.7 EIS Sensors .................................................................................................................. B-15
B.8 Antennas ....................................................................................................................... B-19
B.9 ADS-B Antenna Interface .............................................................................................. B-20
B.10 COM Antenna Interface ................................................................................................ B-20
B.11 Marker Beacon Antenna Interface ................................................................................ B-21
LIST OF ILLUSTRATIONS
FIGURE PAGE
Figure 2-1 – GDU 460 (Single PFD, with EIS Optional) .................................................................. 9
Figure 2-2 – GDU 470 (PFD) ......................................................................................................... 10
Figure 2-3 – GSU 25D ADAHRS ................................................................................................... 11
Figure 2-4 – GMU 11 Magnetometer ............................................................................................. 11
Figure 2-5 – GTP 59 ...................................................................................................................... 12
Figure 2-6 – GAD 29B/29D (ARINC 429 Adapter) ........................................................................ 12
Figure 2-7 – GAD 27 ...................................................................................................................... 13
Figure 2-8 – GEA 24(B) Engine and Airframe Unit ........................................................................ 13
Figure 2-9 – GDL 52R Data Link ................................................................................................... 15
Figure 2-10 – GPS Antenna (011-04036-10 Shown) ..................................................................... 15
Figure 2-11 – GAP 26 AOA Probe ................................................................................................. 16
Figure 2-12 – GTR 20 COM Radio ................................................................................................ 16
Figure 2-13 – GTR 200B COM Radio ............................................................................................ 17
Figure 2-14 – GMA 245R Audio Panel .......................................................................................... 17
Figure 2-15 – Example G3X Architecture ...................................................................................... 18
Figure 2-16 – Example G3X Architecture – Standalone MFD ....................................................... 20
Figure 3-1 – GDU Features and Controls ...................................................................................... 24
Figure 3-2 – Split/Full Format Buttons - GDU 460 ...................................................................... 25
Figure 3-3 – Split/Full Format Buttons - GDU 470 ...................................................................... 25
Figure 3-4 – Normal Mode, Full Format – PFD w/ EIS (Example)................................................. 25

Page viii
Figure 3-5 – Normal Mode, Split Format – PFD W/ EIS (Example)............................................... 26
Figure 3-6 – Normal Mode, Full – MFD with EIS (Example) .......................................................... 27
Figure 3-7 – GDU Knob Function Example ................................................................................... 28
Figure 3-8 – Data Entry Options (Examples) ................................................................................. 28
Figure 3-9 – Configuration Mode Pages ........................................................................................ 29
Figure 5-1 – Incorrect CAN Bus Topographies .............................................................................. 40
Figure 5-2 – Correct CAN Bus Wiring Example and Node Connections ....................................... 40
Figure 5-3 – Network Error Rate (Configuration/Diagnostic Mode) ............................................... 41
Figure 5-4 – Heading Failure Indication ......................................................................................... 46
Figure 5-5 – Attitude Failure Indication .......................................................................................... 47
Figure 5-6 – Magnetometer Interference Test On-screen Instructions .......................................... 49
Figure 5-7 – Magnetometer Interference Test Progress ................................................................ 50
Figure 5-8 – Magnetometer Interference Test Status .................................................................... 50
Figure 5-9 – Engine/Airframe Failure Indications........................................................................... 52
Figure 5-10 – View of P4X01 Connector from back of GDU ......................................................... 57
Figure 5-11 – View of P4X02 Connector from back of GDU ......................................................... 57
Figure 5-12 – View of J251 Connector on the GSU 25D ............................................................... 59
Figure 5-13 – View of J252 Connector on the GSU 25D ............................................................... 59
Figure 5-14 – View of J111 Connector on the GMU 11 ................................................................. 60
Figure 5-15 – View of J271 Connector on the GAD 27 ................................................................. 61
Figure 5-16 – View of TB273 Terminal Block on GAD 27 ............................................................. 63
Figure 5-17 – View of J241 Connector on the GEA 24(B) ............................................................. 63
Figure 5-19 – View of J243Connector on the GEA 24(B) .............................................................. 65
Figure 5-21 – View of J291 Connector on the GAD 29B/29D ....................................................... 67
Figure 5-22 – View of J292 Connector on the GAD 29B/29D ....................................................... 68
Figure 5-23 – View of J5X1 Connector on the GDL 5XR .............................................................. 69
Figure 5-24 – View of J2001 Connector on GTR 20 or GTR 200B ............................................... 69
Figure 5-25 – View of J2401 Connector on GMA 245R ................................................................ 70
Figure 5-26 – View of J2402 Connector on GMA 245R ................................................................ 72
Figure 6-1 – GDU 460 Shown, (GDU 470 Similar) ........................................................................ 75
Figure 6-2 – Configuration Module (PFD) ...................................................................................... 76
Figure 6-3 – GDU 460-Mounted GSU 25D (GDU 470 similar) ...................................................... 77
Figure 6-4 – Remote mounted GSU 25D ....................................................................................... 78
Figure 6-5 – GMU 11 Magnetometer ............................................................................................. 79
Figure 6-6 – GTP 59 Temperature Probe ...................................................................................... 80
Figure 6-7 – GAD 27 ...................................................................................................................... 81
Figure 6-8 – GEA 24(B) ................................................................................................................. 82
Figure 6-9 – Brass Pressure Sensor (Coupling Mount Example) .................................................. 84
Figure 6-10 – GPT Pressure Sensor (Housing & Coupling Mount Examples) .............................. 85
Figure 6-11 – Carburetor Air Temperature Sensor Mounting ........................................................ 86
Figure 6-12 – Fuel Flow Transducer Installation Example ............................................................ 88
Figure 6-13 – GAD 29B/29D .......................................................................................................... 89

Page ix
Figure 6-14 – GDL 5XR (GDL 52R Shown) ................................................................................... 90
Figure 6-15 – GPS Antenna (Screw-mounted Installation Example) ............................................ 91
Figure 6-16 – GPS Antenna (Hook and Loop Installation Example) ............................................. 92
Figure 6-17 – GTR 20 VHF COM Radio ........................................................................................ 93
Figure 6-18 – GMA 245R Audio Panel .......................................................................................... 94
Figure 6-19 – GAP 26 Mechanical Splice Detail (14-volt Aircraft with 10 AWG Wire) .................. 95
Figure 6-20 – GAP 26 AOA Probe Assembly ................................................................................ 96
Figure 7-1 – Aircraft Level Attitude .............................................................................................. 100
Figure 7-2 – Pitch/Roll Offset Calibration in Progress ................................................................. 101
Figure 7-3 – Pitch/Roll Offset Completion Status ........................................................................ 101
Figure 7-4 – Compass Rose Starting Position ............................................................................. 102
Figure 7-5 – Magnetometer Calibration On-Screen Instructions ................................................. 103
Figure 7-6 – Magnetometer Calibration Progress ........................................................................ 103
Figure 7-7 – Static Pressure Calibration ...................................................................................... 104
Figure 7-8 – Static Pressure Calibration Warning........................................................................ 104
Figure 7-9 – Static Pressure Calibration Instructions .................................................................. 105
Figure 7-10 – Static Pressure Calibration in Progress ................................................................. 105
Figure 7-11 – Static Pressure Calibration Completion Status ..................................................... 105
Figure 7-12 – Update Software Window (Example) .................................................................... 112
Figure 7-13 – Data Link Page ...................................................................................................... 114
Figure 8-1 – Transponder Setup Page (Normal Mode) ............................................................... 116
Figure 8-2 – Lightning Tab ........................................................................................................... 122
Figure A-1– Generic Aircraft Figure ............................................................................................. A-4
LIST OF TABLES
TABLE PAGE
Table 1-1 – Required Documents .................................................................................................... 5
Table 2-1 – G3X Touch AML STC Installed Sensors .................................................................... 14
Table 2-2 – GDL 5XR Data Link Features and Functions ............................................................. 14
Table 2-3 – G3X Touch and Supporting Equipment ...................................................................... 22
Table 2-4 – LRU Current Draw ...................................................................................................... 22
Table 3-1 – LRU Status Indicator Symbols .................................................................................... 29
Table 4-1 – Maintenance Intervals ................................................................................................. 33
Table 4-2 – Electrical Bonding Procedure ..................................................................................... 36
Table 5-1 – Status LED Indications ............................................................................................... 39
Table 5-2 – LED Indications Recommended Action ...................................................................... 39
Table 5-3 – CAN Network Error Values (Configuration/Diagnostic Mode) .................................... 41
Table 5-4 – Unit Communication Error Messages (Dual GDU Installations) ................................. 43
Table 5-5 – GDU Reboot During Engine Start ............................................................................... 44
Table 5-6 – ADAHRS and Magnetometer Troubleshooting ........................................................... 45
Table 5-7 – Magnetometer Interference Test Sequence Example ................................................ 51
Table 5-8 – EIS Gauges Troubleshooting...................................................................................... 52
Table 5-9 – Traffic Alert Troubleshooting....................................................................................... 54
Table 5-10 – Transponder Alert Troubleshooting .......................................................................... 54

Page x
Table 5-11 – Loss of Navigation Information (External Navigators) .............................................. 55
Table 5-12 – Miscellaneous Alerts ................................................................................................. 56
Table 5-13 – P4X01/J4X01 Pin Functions ..................................................................................... 57
Table 5-14 – P4X02/J4X02 Pin Functions ..................................................................................... 58
Table 5-15 – P251/J251 Pin Functions .......................................................................................... 59
Table 5-18 – GTP 59 Lead Wire Functions ................................................................................... 61
Table 5-20 – TB273 Terminal Functions ........................................................................................ 63
Table 5-27 – P5X1/J5X1 Pin Functions ......................................................................................... 69
Table 5-28 – P2001/J2001 Pin Functions ...................................................................................... 69
Table 5-31 – GMA 245R DIP Switch Configuration Settings ......................................................... 73
Table 6-1 – GDU Configuration Module Kit (P/N 010-12253-01) .................................................. 76
Table 7-1 – GSU 25D/GMU 11 Recalibration Criteria ................................................................. 100
Table 8-1 – LRU Status Indicators ............................................................................................... 115
Table 8-2 – Airspeed Test Points ................................................................................................. 127
Table 8-3 – Heading Verification – ADAHRS Check ................................................................... 128
Table 8-4 – EMI Victim/Source Matrix ......................................................................................... 137
Table A-1 – G3X Post-Installation Log ......................................................................................... A-2
Table A-2 – G3X Equipment Locations ........................................................................................ A-3
Table B-1 – Compatible Equipment – GPS/VHF Nav Interfaces ................................................. B-1
Table B-2 – Compatible Equipment – GPS NAV ......................................................................... B-5
Table B-3 – Compatible Equipment – VHF NAV/COM ................................................................ B-7
Table B-4 – Compatible Traffic and Weather Sources ................................................................ B-8
Table B-5 – Compatible Equipment – Non-Garmin Autopilots .................................................. B-11
Table B-6 – Compatible Equipment – Audio Panel ................................................................... B-14
Table B-7 – Compatible EIS Sensors ........................................................................................ B-15
Table B-8 – Supported GPS & SXM Antennas .......................................................................... B-19
Table B-9 – GPS or GPS/WAAS Antenna Minimum Requirements .......................................... B-20
Table B-10 – SXM Satellite Radio Antenna Minimum Requirements ........................................ B-20

Page xi
1. INTRODUCTION
1.1 Content, Scope, Purpose

This document provides Instructions for Continued Airworthiness (ICA) for the Garmin G3X Touch EFIS
Part 23 AML STC as installed in Part 23 aircraft under Supplemental Type Certificate (STC) SA01899WI.
This document satisfies the requirements for continued airworthiness as defined by 14 CFR Part 23.1529
Appendix G. Information in this document is required to maintain the continued airworthiness of the G3X
Touch EFIS systems.
1.1.1 Applicability
This document applies to all aircraft with the G3X Touch system installed in accordance with AML STC
SA01899WI.
Modification of an aircraft by this STC obligates the aircraft operator to include the maintenance
information provided by this document in the operator’s Aircraft Maintenance Manual and the operator’s
Aircraft Scheduled Maintenance Program.

Page 1
1.2 Organization
This manual is structured as described below:
Section 2: System Description
Provides an overview of the G3X Touch EFIS system equipment installed by this STC.
Section 3: Control & Operation
Presents basic control and operation information specifically tailored to maintenance practices. Basic
G3X Touch Configuration Mode operation is also described.
Section 4: Instructions for Continued Airworthiness
Provides maintenance instructions for Continued Airworthiness of the G3X Touch EFIS system.
Section 5: Troubleshooting
Provides troubleshooting information to aid in diagnosing and resolving potential problems with
equipment and functions installed by this STC.
Section 6: G3X Equipment Removal & Replacement
Gives instructions for the removal and replacement of G3X Touch EFIS equipment.
Section 7: G3X Equipment Configuration & Testing

Gives instructions for loading software, configuring, and testing of G3X Touch EFIS equipment.
Section 8: System Return to Service Procedure

Specifies return-to-service (checkout) procedures to be performed upon completion of maintenance of the
G3X Touch EFIS system.
Appendix A: Installation Specific Information
Provides a template to record aircraft-specific installation and configuration data for the G3X Touch EFIS
system.

Page 2
1.3 Acronyms & Abbreviations
AC: Advisory Circular GFC: Garmin Automatic Flight Control System
ADAHRS: Air data, Attitude and Heading GMU: Garmin Magnetometer Unit
Reference System. GNS: Garmin Navigation System
ADI: Attitude Direction Indicator GNX: Garmin Navigator Transponder
ADS-B: Automatic Dependent Surveillance - GPS: Global Positioning System
Broadcast GPSS: GPS Roll Steering
ADS-R: Automatic Dependent Surveillance - GSU: Garmin Sensor Unit
Rebroadcast
GTN: Garmin Touch Navigator
AFCS: Aircraft Flight Control System
GTP: Garmin Temperature Probe
AFM: Airplane Flight Manual
GTR: Garmin Transmitter / Receiver
AHRS: Attitude and Heading Reference System
GTS: Garmin Traffic System
ALT: Altitude Preselect
GTX: Garmin Transponder
AML: Approved Model List
HDG: Heading (mode)
AND: Logical AND
HSDB: High Speed Data Bus
AOA: Angle of Attack
HSI: Horizontal Situation Indicator
ARINC: Aeronautical Radio, Incorporated
IAS: Indicated Air Speed
AS: Aerospace Standard
ICA: Instructions for Continued Airworthiness
ASI: Airspeed Indicator
ID: Identifier
AWG: American Wire Gauge
IFR: Instrument Flight Rules
BNC: Bayonet Neill–Concelman
IGRF: International Geomagnetic Reference
CAN: Controller Area Network Field
CDI: Course Deviation Indicator ILS: Instrument Landing System
CDU: Control Display Unit KTS: Knots
CE: European Committee LCD: Liquid Crystal display
CFR: Code of Federal Regulations LED: Light Emitting Diode
CHT: Chart Processing LNAV: Lateral Navigation
CI: Course to Intercept LOC: Localizer
COM: Communication Radio LRU: Line-Replaceable Unit
CRS: Course METAR: Meteorological Terminal Aviation
CS: Conducted Susceptibility Routine Weather Report
DC: Direct Current MFD: Multi-Function Display
DDM: Difference in Depth of Modulation MFR: Manufacturer
DME: Distance Measuring Equipment NEXRAD: Next-Generation Radar
DMM: Digital Multi Meter NMEA: National Marine Electronics Association
ECO: Engineering Change Order OAT: Outside Air Temperature
EEPROM: Electrically Erasable Programmable OBS: Omni Bearing Selector
Read-Only Memory OR: Logical OR
EFIS: Electronic Flight Instrument System PFD: Primary Flight Display
EGT: Exhaust Gas Temperature POH: Pilot’s Operating Handbook
EIS: Engine Indication System RPM: Revolutions per Minute
EMC: Electromagnetic Compatibility RTCA: Radio Technical Commission for
EMI: ElectroMagnetic Interference Aeronautics
ES: Extended Squitter RX: Receive
FAA: Federal Aviation Administration SAS: Stability Augmentation System
FF: Fuel Flow SD: SanDisk Memory
FIS-B: Flight Information Service Broadcast STC: Supplemental Type Certificate
GA: Go-Around SXM: Sirius XM
GAD: Garmin Adapter SYS: System
GDL: Garmin Datalink LRU TAS: Traffic Advisory System
GDU: Garmin Display Unit OR
GEA: Garmin Engine and Airframe Unit True Airspeed

Page 3
TAWS: Terrain Awareness and Warning System UHF: Ultra High Frequency
TCAS: Traffic Collision Avoidance System VDC: Volts of Direct Current
TIS: Traffic Information Service VFR: Visual Flight Rules
TIS-A: Traffic Information Service-A VHF: Very High Frequency
TIS-B: Traffic Information Service - Broadcast VLOC: VOR/Localizer
TIT: Turbine Inlet Temperature VNAV: Vertical Navigation
TNC: Threaded Neill–Concelman VOR: VHF Omni Directional Radio Range
TSO: Technical Standard Order WAAS: Wide Area Augmentation System
TX: Transmit WPT: Waypoint
UAT: Universal Access Transceiver XM: XM Satellite Radio

Page 4
1.4 Publications
The following documents are required by this maintenance manual to perform maintenance. It is the
responsibility of the owner / operator to ensure latest versions of these documents are used during
operation, servicing or maintenance of the airplane.
Table 1-1 – Required Documents
Document Number Garmin Document Title
190-02472-00 Garmin G3X Pilot’s Guide for Certified Aircraft
190-02472-01 Garmin G3X Touch EFIS Part 23 AML STC Installation Manual
1.5 Revision and Distribution

This document is required for maintaining the continued airworthiness of the aircraft. When this document
is revised, each page will also be revised to indicate the current revision level.
Garmin Dealers may obtain the latest revision of this document on the Garmin Dealer Resource Center
website.
Owners/operators may obtain the latest revision of this document by one of the following methods:
• Visit https://fly.garmin.com/support
• Contact a Garmin dealer
• Contact Garmin Product Support at 913-397-8200, toll free 866-739-5687

Page 5
2. SYSTEM DESCRIPTION
This section provides an overview of the line replaceable units (LRUs) installed by the G3X Touch EFIS
Part 23 AML STC.
The Garmin G3X Touch EFIS replaces the standard pneumatic instruments (altimeter, airspeed indicator
(ASI) and vacuum attitude gyro indicator) and combines primary flight instrumentation, aircraft systems
instrumentation, and navigational information, all displayed on up to four color Garmin Display Units
(GDU) 4X0. The following functionalities can be provided by the G3X Touch EFIS system:
• Multi-Function Display (MFD)
• Optional Primary Flight Display (PFD)
• Optional Engine Indicating System (EIS)
• Optional Traffic and Weather Receiver (ADS-B In)
• Optional SiriusXM Weather and Radio (subscription required)
• Optional Angle of Attack (AOA)
• Optional VHF COM (panel or remote mount)
• Optional Audio Panel (remote mount)
• Optional Landing and Taxi Light Wig-Wag
A G3X system installed per this STC may consist of one of the following display configurations for the
Pilot-in-Command:
1. Single GDU 4X0 installed as a standalone MFD with no PFD no GSU 25D present, and optional
EIS supported.
2. Single 7-inch GDU 470 (portrait orientation) PFD with the capability to be split into a PFD/MFD
configuration but with no support for EIS.
3. Single 10.6-inch GDU 460 with PFD/MFD split capability and EIS supported.
4. Dual 7-inch GDU 470 (portrait orientation), one configured as PFD and the other as MFD, with
EIS only supported on the MFD.
5. Single 7-inch GDU 470 (portrait orientation) as PFD and a single 10.6-inch GDU 460 as MFD with
the EIS only supported on 10.6-inch MFD.
6. Single 10.6-inch GDU 460 as PFD and a single 7-inch GDU 470 (portrait orientation) as MFD,
with the EIS supported in either the PFD or MFD.
7. Dual 10.6-inch GDU 460, one configured as PFD and the other as MFD, with EIS supported on
either the PFD or MFD.
Additional displays for the Copilot may be installed on the right side of the panel in a side-by-side cockpit
or second cockpit in a tandem aircraft. A maximum of three GDUs can be installed in a side-by-side
aircraft and four GDUs in a tandem aircraft.
When at least two GDUs are installed, one as PFD and the other as an MFD, failure of one display unit
will cause the system to automatically revert to a reversionary format. In the reversionary format, primary
flight information, radio tuning information and EIS (if installed) are displayed on the remaining GDU.
Additionally, a multi-function pane can be displayed if the “split” touchscreen button is selected.
Each of the above display configurations require the following LRUs and equipment as part of the
installation:
• GSU 25D Air Data Computer, Aircraft Heading and Reference System (ADAHRS) (required for
PFD)
• GMU 11 Magnetometer (required for PFD)
• GTP 59 Temperature Probe (required for PFD)
• GPS Antenna (required by all display configurations)

Page 6
• GAD 27 Electronic Adaptor Unit (required for 14-volt aircraft with EIS unless a TCW IBBS is
connected to the GDU, GSU 25D, and GEA 24(B) per AML STC #SA04400NY)
The GAD 27 Electronic Adapter Unit can provide stabilized power output during low voltage events and is
required for 14-volt aircraft with EIS unless a TCW IBBS is connected to the GDU, GSU 25D, and GEA
24(B) per AML STC #SA04400NY. The GAD 27 may optionally be installed on both 14 and 28 -volt
aircraft to provide the ability to flash the landing and/or taxi lights in an alternating fashion, otherwise
known as “Wig Wag”.
Standby attitude, airspeed, and altitude instruments are required if a G3X display unit is installed as the
primary flight display (PFD) in IFR installations. The standby instruments may be a Garmin G5, GI 275, or
existing pneumatic instruments. IFR installations which include Copilot displays must use the G5 or GI
275.
The G3X system is composed of several sub-units or Line Replaceable Units (LRUs). The LRUs have a
modular design and can be installed directly behind the instrument panel or mounted directly on the panel
in the case of a GDU, or in a separate location. Each LRU has a particular function, or set of functions, as
described in their applicable sections.
A GPS antenna is required for G3X installations. The GDU contains an internal WAAS GPS receiver
which supports VFR navigation only. IFR navigation requires a compatible certified navigator that can
interface to the G3X system and display flight plan and guidance on the GDU. Alternatively, navigation
equipment that is not compatible with G3X can retain their separate external indicator to maintain IFR
capability. The external indicator installation is outside the scope of this STC.
G3X systems using optional SiriusXM (SXM) or ADS-B receivers require dedicated antennas which are
not installed under this STC.
Standalone MFD Installation
The G3X Touch AML STC approves the installation of either a GDU 470 or 460 as a standalone MFD (no
PFD and no GSU 25D installed). Compared to fully featured G3X Touch system where an MFD is
installed with a PFD, the standalone MFD supports most of the same MFD functions and interfaces
including:
• Moving map, charts, terrain, VFR flight planning, and EIS
• Weather and traffic from GDL 5XR, GTX 345(R), GNX 375, GTS 8XX
• Interface to Garmin COM & NAV radios with frequency tuning and display
• Control and display of GTR 20 and GMA 245R
• Analog audio output of G3X aural alerts including altitude, terrain, traffic, GFC 500, and EIS
• Interface to external Garmin GPS navigators with ability to select between display of internal VFR
flight plan or external navigator flight plan
• Interface to one or two G5s which can display lateral and vertical deviation from the MFD’s built-in
VFR navigation and VNAV functions
• Interface to the GFC 500 autopilot (requires a G5) which allows the autopilot to follow the MFD’s
built-in VFR flight plan and VNAV descent profile
• Interface to the non-Garmin autopilots approved under this STC (requires a G5 and GAD
29B/29D) which allows the autopilot to follow the MFD’s built-in VFR flight plan using GPSS mode
on the G5
• Interface to a GAD 13 OAT (when installed with a G5 ADI) which supports the Glide Range Ring
function on the MFD
• Interface to a GMU 11 (when installed with a G5) which allows the MFD to send heading data to
WX-500 lightning detector or GTS 8XX traffic systems
• Interface to GAD 27 (optional for wig-wag function; required for 14v installations with EIS unless a
TCW IBBS is connected to the GDU and GEA 24(B) per AML STC #SA04400NY)
The standalone MFD does not support altitude encoder function or remote control of any transponder.

Page 7
2.1 Equipment Descriptions
2.1.1 GDU 460
The Garmin Display Unit (GDU) 460 provides a central display and user interface for the G3X Touch EFIS
Touch system. GDU 460 is a 10.6-inch landscape-oriented, panel mounted control and display unit with
a GPS receiver. The GDU features a high-resolution infrared touchscreen user interface augmented by a
set of dual-concentric knobs and dedicated buttons for commonly used functions. The GDU 460 is
mounted flush to the aircraft instrument panel. Below is a list of some of the functions provided by the
GDU 460.
Many of the listed functions depend on optional equipment interfaces and/or subscription services.
PFD Functions
• Primary attitude, heading, and air data information
• Slip/skid and rate-of-turn indication
• Synthetic Vision including Pathways and Flight Path Marker
• Horizontal Situation Indicator (HSI)
• Flight Director display with GFC500 autopilot modes and alerts
• Clock and timer
MFD Functions
• Moving map with VFR flight planning function
• Charts and SafeTaxi
• Traffic display and alerting
• Terrain and obstacle display and alerting
• Datalink weather
• Display of flight plan and navigation from an external Garmin GPS navigator
• Display of navigation from an external VOR/ILS NAV radio
• Control and display of Transponder (not supported in Standalone MFD)
• Control and display of COM and NAV radios
System Interfaces
• Display engine parameters when configured and interfaced with a Garmin Engine Adapter, GEA
24(B).
• Wireless Bluetooth transceiver that can communicate with tablet computers and other Garmin
devices that support Connext interface protocol. Refer to G3X Touch Pilot’s Guide for Certified
Aircraft (190-02472-00) for guidance in using Connext Bluetooth connections.
• CAN and RS-232 interfaces to communicate with Garmin LRUs and other devices. Refer to the
appropriate sections in G3X Touch EFIS Part 23 AML STC Installation Manual (190-02472-01)
for interconnect and configuration information.
• BNC connector for GPS antenna interface.
The GDU 460 may be installed in various configurations as described in Section 2 (System Description).
Figure 2-1 example shows a GDU 460 installed as PFD/MFD split functionality with EIS supported.

Page 8
Figure 2-1 – GDU 460 (Single PFD, with EIS Optional)
2.1.2 GDU 470

The Garmin Display Unit (GDU) 470 provides a central display and user interface for the G3X Touch EFIS
Touch system. The Garmin Display Unit (GDU) 470 is a 7-inch LCD portrait-oriented panel mounted
control and display unit with a GPS receiver. The GDU features a high-resolution infrared touchscreen
user interface augmented by a set of dual-concentric knobs and dedicated buttons for commonly used
functions. The GDU 470 is mounted flush to the aircraft instrument panel. Below is a list of some of the
functions provided by the GDU 470.
Many of the listed functions depend on optional equipment interfaces and/or subscription services.
PFD Functions
• Primary attitude, heading, and air data information
• Slip/skid and rate-of-turn indication
• Synthetic Vision including Pathways and Flight Path Marker
• Horizontal Situation Indicator (HSI)
• Flight Director display with GFC500 autopilot modes and alerts
• Clock and timer
MFD Functions
• Moving map with VFR flight planning function
• Charts and SafeTaxi
• Traffic display and alerting
• Terrain and obstacle display and alerting
• Datalink weather
• Display of flight plan and navigation from an external Garmin GPS navigator
• Display of navigation from an external VOR/ILS NAV radio
• Control and display of Transponder (not supported in Standalone MFD)

Page 9
• Control and display of COM and NAV radios
System Interfaces
• Display engine parameters when configured and interfaced with a Garmin Engine Adapter, GEA
24(B).
• Wireless Bluetooth transceiver that can communicate with tablet computers and other Garmin
devices that support Connext interface protocol. Refer to G3X Touch Pilot’s Guide for Certified
Aircraft (190-02472-00) for guidance in using Connext Bluetooth connections.
• CAN and RS-232 interfaces to communicate with Garmin LRUs and other devices. Refer to the
appropriate sections in the G3X Touch EFIS Part 23 AML STC Installation Manual (190-02472-
01) for interconnect and configuration information.
• BNC connector for GPS antenna interface.
The GDU 470 may be installed in various configurations as described in Section 2 (System Description).
Figure 2-2 example shows a GDU 470 installed as a PFD. EIS is only supported on a GDU 470 when
configured as an MFD.
The display on a 7” GDU when configured as an MFD (in a multiple display configuration) does not have
split format functionality in normal mode but is available in reversionary mode if the PFD fails.
NOTE
EIS is not supported in a single GDU 470 installation.
Figure 2-2 – GDU 470 (PFD)

Page 10
2.1.3 GSU 25D ADAHRS
The GSU 25D is an LRU that provides Air Data Computer and Attitude Heading Reference System
(ADAHRS) information. The GSU 25D interfaces to a remote mounted GMU 11 magnetometer for
heading information, and computes OAT and TAS from inputs provided by the GTP 59. The GSU 25D is
connected to existing primary pitot/static system. Only one GSU 25D is approved for installation and
interface by this STC.
When a GAP 26 probe is installed, the GSU 25D also computes AOA from inputs provided by the GAP 26
as well as the aircraft’s pitot/static system, and is subsequently displayed by the G3X PFD.
Figure 2-3 – GSU 25D ADAHRS
2.1.4 GMU 11 Magnetometer

The Garmin GMU 11 Magnetometer is a remote mounted device that provides magnetic field
measurements to the GSU 25D to support computation of flight attitude and heading data.
Figure 2-4 – GMU 11 Magnetometer
2.1.5 GTP 59 Temperature Probe

The Garmin GTP 59 is an externally mounted temperature probe that provides raw outside air
temperature data. The device is a three-wire temperature probe interface.

Page 11
Figure 2-5 – GTP 59
2.1.6 GAD 29B/29D ARINC 429 Adapter (Optional)

The GAD 29B/29D allows the G3X system to interface to IFR GPS navigators such as the Garmin GPS
175, GNX 375, GNC 355(A), GNS and GTN series. It also allows for interface to some non-Garmin
autopilots.
Figure 2-6 – GAD 29B/29D (ARINC 429 Adapter)
2.1.7 GAD 27 Electronic Adapter Unit

The GAD 27 provides a stabilized 12V power output to keep EIS online during engine start when battery
voltage drops. It is installed on airplanes with a 14-volt electrical system that install the G3X EIS option
unless a TCW IBBS is connected to the GDU, GSU 25D, and GEA 24(B) per AML STC #SA04400NY. It
may be installed on aircraft with a 14-volt electrical system that do not have EIS to prevent reboot during
temporary low battery voltage levels. Refer to Appendix A.1 for installed equipment.
If a GAD 27 is not installed on 14-Volt aircraft and a PFD/MFD reboot is observed, troubleshoot the
aircraft per guidance in Section 5.3.5.
The GAD 27 may optionally be installed on both 14 and 28-volt aircraft to provide the ability to flash the
landing and/or taxi lights of the airplane in an alternating fashion, otherwise known as “Wig Wag”. This is
the only approved GAD 27 function for 28-volt aircraft.

Page 12
Figure 2-7 – GAD 27
2.1.8 GEA 24(B) Engine/Airframe Unit

The Garmin Engine and Airframe GEA 24(B) is an input/output system used to monitor and power engine
and airframe sensors. The GEA 24(B) is used to monitor and display engine data for single engine aircraft
with up to 6 cylinders.
Figure 2-8 – GEA 24(B) Engine and Airframe Unit

NOTE
For most interfaces the GEA 24 and GEA 24B are interchangeable with the same wiring and
configuration settings, however the GEA 24 interface to resistive fuel probes must use a pair
of 2.2kΩ resistors and be configured as ‘Voltage’ interfaces (refer to Garmin SB 2134 and
Installation Manual Rev.9 or later). If a GEA 24 is replaced by a GEA 24B, any fuel quantity
interfaces to resistive probes must be recalibrated regardless of whether the 2.2kΩ resistors
in the harness are retained or removed. For new installations with a GEA 24B, the resistors
are not required, reference the STC Installation Manual Rev 14 (or later).
2.1.8.1 EIS Functionality

If a GEA 24(B) is installed, configured engine data and airframe parameters are displayed on the GDU.
This manual only provides information for the EIS sensors that were installed by the G3X Touch EFIS
Part 23 AML STC.
Table 2-1 lists the sensors that are maintained in this manual. Refer to the applicable maintenance data
and/or TSO manual for other sensors that are interfaced to the EIS.

Page 13
Table 2-1 – G3X Touch AML STC Installed Sensors
Function Description Garmin Part Number
Oil Pressure Garmin 150 PSIG Pressure, Brass 011-04202-30
Garmin GPT 150 PSIG Pressure, S.S. 011-05783-30
Oil Temperature UMA T3B3-2.5G (K Type Probe) 494-70009-00
Manifold Pressure Garmin 30 PSIA Pressure, Brass 011-04202-00
Garmin GPT 30 PSIA Pressure, S.S. 011-05783-00
Carb Air Temperature UMA T3B10-SG (K Type Probe) 494-70010-00
Fuel Pressure Garmin 75 PSIG Pressure, Brass 011-04202-20
Garmin 15 PSIG Pressure, Brass 011-04202-10
Fuel Flow & Return FF EI FT-60 494-10001-00
EI FT-90 494-10001-01
2.1.9 GDL 5XR Data Link

GDL 5XR provides the data and functions shown in Table 2-2 via Bluetooth® wireless technology and/or
over wired connections.
Note: Approved software for PMA GDL 5XR units can only be loaded via the G3X GDU (reference
Software Loading Procedure, Section 7.13). The ability to update GDL 5XR software via Bluetooth
connections has been disabled for PMA GDL 5XR units.
Table 2-2 – GDL 5XR Data Link Features and Functions
GDL 50R GDL 51R GDL 52R
ADS-B Receiver (Traffic and Sirius XM Receiver ADS-B Receiver (Traffic and
Weather) (Weather/audio) Weather) and Sirius XM
Receiver (Weather/audio)
The GDL 5XR are remote mounted and require external antennas and power connections. No battery is
provided.
The GDL 50R/52R receives Traffic (ADS-B/ADS-R and TIS-B) on both Universal Access Transceiver
(UAT) and 1090 ES (Extended Squitter) frequency bands. When in range of a ground station, these units
will receive FIS-B weather over the UAT link.
The GDL 5XR products provide information to G3X Touch displays via RS-232 and to devices running
Garmin Pilot™ via a Connext® data connection (via Bluetooth®). Please see additional information in the
G3X Touch Pilot's Guide for Certified Aircraft (190-02472-00).

Page 14
Figure 2-9 – GDL 52R Data Link
2.1.10 Antennas
The optional glareshield-mounted GPS antenna (Garmin part number 011-04036-10 or 011-04036-00)
feeds a GPS receiver inside the GDU which provides position, velocity, and time data to support various
display functions. The GPS data is also passed on to the GSU 25D to provide improved AHRS
performance.
A GPS antenna must be connected to the PFD or the Standalone MFD. In a multiple display G3X
installation the PFD will pass GPS data to the other displays. A second GPS antenna is not required but
may optionally be installed and connected to the MFD for redundancy.
There are other GPS antennas which are compatible with the GDUs, reference Table B-8 for more
information.
NOTE
If using GPS antenna 011-04036-00, which has a TNC connector, a TNC/BNC Adapter (p/n 330-01754-
00) is required to connect the GPS antenna to the GDU.
Figure 2-10 – GPS Antenna (011-04036-10 Shown)
2.1.11 GAP 26 AOA Probe

The GAP 26 AOA (Angle of Attack) probe is a heated air data probe intended to be used as part of the
G3X system.
When installed by this STC, the GAP 26 AOA pressure port is plumbed to the GSU 25D ADAHRS to
provide AOA pressure. The GSU 25D will use the pressure from the GAP 26 probe and the pitot/static
pressures it already receives from the existing aircraft pitot/static system to determine AOA and
subsequently, display it on the G3X PFD.

Page 15
Figure 2-11 – GAP 26 AOA Probe
2.1.12 GTR 20 VHF COM Radio

The GTR 20 is a remote VHF COM transceiver that operates in the 118.000 to 136.975 MHz frequency
range with a 25 kHz channel spacing. The GTR 20 features a built-in two-place stereo intercom with alert
audio, 3D audio, and stereo music inputs.
As installed by this STC, the GTR 20 is a remote mounted COM radio that is entirely controlled by the
G3X Touch display with no front-panel interface. Use of the intercom function is optional.
Figure 2-12 – GTR 20 COM Radio
2.1.13 GTR 200B VHF COM Radio

The GTR 200B is a VHF COM transceiver that operates in the 118.000 to 136.975 MHz frequency range
with a 25 kHz channel spacing. The GTR 200B features a built-in two-place stereo intercom with alert
audio, 3D audio, stereo music inputs, and Bluetooth functionality.
As installed by this STC, GTR 200B COM radio can be controlled either by the G3X Touch displays or by
its own front-panel controls. Use of the intercom function is optional.

Page 16
Figure 2-13 – GTR 200B COM Radio
2.1.14 GMA 245R Audio Panel with Marker Beacon
The GMA 245R is a remote mounted high-fidelity digital audio panel that collects, processes, and
distributes audio signals to the pilot and passengers and is fully controlled by G3X Touch displays. It
interfaces to dual NAV and COM radios and features a 6-place stereo intercom with 3D audio and
Bluetooth capability.
Figure 2-14 – GMA 245R Audio Panel
2.2 G3X Optional Interfaces

See APPENDIX B for equipment that may be connected to and interfaced with a G3X Touch system.

Page 17
2.3 G3X Touch Architecture Example
G3X Touch AML STC Avionics System

RS-232
GFC500
GAD 27 Aircraft Aircraft
GTP 59 Static Pitot
GDL 5xR
4 (ADS-B In and/or
(Optional) OAT GMC 507
SXM) GSA 28
Wig-Wag
(Optional) A/P Controller Yaw Servo
14 V 14 V 14 V (Optional) (Optional)
to S A P
GEA24 S P
GDU 4x0 GSU 25 G5 GSA 28 GSA 28 GSA 28
8 Standby Trim Servo
PFD 1 RS-232 ADAHRS Pitch Servo Roll Servo
1
(Backup (Optional) (Optional) (Optional) (Optional)
ADAHRS)
A
CAN BUS
RS- RS-232
AOA
232 2
RS-232 GAD
GMU 11 RS-232 GEA 24(B)
13 14 V from
EIS
(Optional) GAD27
GTS 8XX GTX (Optional)
A429 RS-232
TAS/TCAS Transponder (Back up EIS)
5 2
(Optional) (Optional)
HSDB RS-232
Stereo
Audio
GDU 4x0 2
GDU 4x0 Engine/
RS-232 GDU 4x0
PFD 2 GAP 26 MFD 1 Airframe
MFD 2
7
HSDB
2 AOA (Optional)
Sensors
(Optional)
Mono
Audio RS-232 WX-500
MapMx Storm CO
RS-232 RS-232 GTR 20/
scope Detector 3
RS-232 (Optional)
200B COM
(Optional)
(ADS-B)
(Optional)
RS-232
Connext
(Flt Plan
Xfer)
RS-232
No. 1 GPS/NAV/ MapMx
3
COM
A429
(NAV) (Optional)
A429 RS-232
(GPS)
GAD 29B/29D A429
Data (Air Data)
Concentrator A429 No. 2 GPS/NAV/
(Optional) A429 (Air Data) 3,6
(NAV) COM
A429 (Optional)
(GPS) KEY:
Standard
Analog GMA 245R G3X Equip
CRS & HDG Audio 9
Panel Audio
(Optional) Optional
G3X Equip
Non-Garmin
Autopilot Garmin COM or
3,6 Interfacing
6
(Optional) NAV/COM Equip
(Optional)
Figure 2-15 – Example G3X Architecture

Page 18
Notes:
(1) Standby instrument requirements for G3X PFD installations include the following:
• a G5 or GI 275 standby instrument is required if Copilot displays are installed in an IFR aircraft
• a G5 standby instrument is required if a GFC500 autopilot is installed without a Sonalert
• a GI 275 standby instrument cannot be interfaced directly to a GFC500 autopilot (the GFC500
interfaces only to G3X when using a GI 275 as the standby).
(2) HSDB & RS232 Connext interfaces are only applicable with GNX 375 or GTX 345() to support FIS-B
weather & TIS-B traffic display on GTN & GDUs.
(3) G3X interfaces to a maximum of two external navigation sources. Supported external navigation
sources include IFR GPS, VHF NAV, or combination GPS/NAV receivers. In addition, two COM
radios can be selected for display and control on G3X, these can be either standalone COM radios or
integrated into one or more of the navigators.
(4) GAD 27 or TCW IBBS (ref AML STC #SA04400NY) is required for 14v airframes with EIS. GAD 27
may optionally be connected to PFD and GSU 25D in 14v airframes without EIS. GAD 27 may
optionally be installed on both 14 and 28 -volt aircraft to enable the landing and/or taxi light “wig wag”
feature.
(5) A GTS 8XX traffic system cannot be interfaced to the GDU if a GNX 375 is installed.
(6) If a non-Garmin autopilot is installed, only one external navigator (GPS and/or VHF) can be
connected to G3X. A second navigator, if installed, must use a dedicated CDI and cannot interface to
G3X.
(7) PFD 2 installation is only allowed on the second panel of a tandem aircraft.
(8) The AOA port on the GSU 25D is connected to a GAP 26 AOA port, if installed. If a GAP 26 is not
installed the AOA port on the GSU is connected to the aircraft’s static line.
(9) The CAN bus interface to the audio panel is only applicable for a GMA 245R.
GDU 232 Ports:
GDUs have six RS-232 ports. Except as noted below, the ports can be connected to any compatible LRU
and if multiple GDUs are installed they will share the data between them on the CAN bus. The RS-232
architecture shown above is only an example configuration.
The port on the P4x01 connector is only compatible with the GSU 25D or GEA24(B). The five ports on
P4x02 can be configured for any supported interface (including GSU 25D and GEA 24(B)).
When two external navigators are connected, the #1 Nav must be connected to a lower numbered RS-
232 port on the PFD, and the #2 Nav connected to either a higher numbered port on the PFD or any 232
port on the MFD.
GTN Connext interface must be connected to PFD1.
Weather data is not shared between GDUs, therefore the traffic/weather receiver (GNX 375, GTX 345() or
GDL 5xR) should be connected via RS-232 to each GDU. If both SXM and ADS-B In are desired in a
fully optioned single GDU installation (PFD, EIS, and dual Garmin navigators), a GDL 52R should be
used for 232 port availability considerations (the 52R sends both SXM and FIS-B/TIS-B on one RS-232
bus). Note however that the GDL 5xR is not compatible with the GTN, so if ADS-B traffic & weather
display is desired on both G3X and GTN it must be sourced from a GNX 375 or GTX 345() per Note 2
(alternatively, the GTN could use GDL 88 or GDL 69, but these are incompatible with G3X).
Page 19
The PFD interfaces to the GI 275 standby instrument via RS-232, so a fully optioned single GDU
installation may need to use a G5 standby (with CAN bus interface) to support all desired 232 interfaces.
Also, two of the three RS-232 ports on the GI 275 are used for the G3X interface, so the GI 275 standby
cannot interface to dual navigators which use RS-232 (e.g. GNS series).
GTX 335(D)R/345(D)R:
RS-232 port 1 on the GTX335(D)R/345(D)R must be used to connect to the GSU 25D.
G3X Touch AML STC Avionics System – Standalone MFD

RS-232
WX-500
GFC500
Storm GAD 27 Engine/
scope 4 OAT GDL 5xR
(Optional) Airframe (ADS-B In and/or
(Optional) Wig-Wag Sensors Probe SXM)
GMC 507 GSA 28
(Optional) A/P Controller Yaw Servo
RS-232 14 V 14 V
GEA 24(B) GAD

GDU 4x0 RS- 13 G5 GSA 28 GSA 28 GSA 28
EIS
MFD 232 1 Pitch Servo Roll Servo Trim Servo
(Optional) (Optional) (Optional)
CAN BUS
2
RS-232
RS-232
Connext
GTX GMU 11 GTR 20/
RS-
(Flt Plan G5 3
232
Xfer) Transponder 1 (Optional) 200B COM
A429 (Optional) (Optional)
(Optional)
Stereo RS-232
Audio
GTS 8XX 2
2 HSDB
TAS/TCAS HSDB RS-232
5 (ADS-B)
(Optional) RS-232
Mono MapMx
Audio
No. 1 GPS/NAV/
3
A429
COM
A429 (NAV) (Optional)
A429 (GPS)
(Air Data)
GAD 29B/29D
Data A429
7 (Air Data)
Concentrator No. 2 GPS/NAV/
A429 3,6
(Optional) COM
(NAV)
(Optional)
A429
(GPS) KEY:
Standard
Analog GMA 245R G3X Equip
CRS & HDG Audio 8
Panel Audio
(Optional) Optional
G3X Equip
Non-Garmin
Autopilot Garmin COM or
3,6 Interfacing
6 NAV/COM
(Optional) Equip
(Optional)
RS-232
Figure 2-16 – Example G3X Architecture – Standalone MFD

Page 20
Notes:
(1) If GFC500 is installed with a G3X Standalone MFD, a G5 is required. A second G5 may be installed
per the G5 AML STC.
(2) HSDB & RS232 Connext interfaces only applicable with GNX 375 or GTX 345() to support FIS-B
weather & TIS-B traffic display on GTN & GDU.
(3) G3X interfaces to a maximum of two external navigation sources. Supported external navigation
sources include IFR GPS, VHF NAV, or combination GPS/NAV receivers. In addition, two COM
radios can be selected for display and control on G3X, these can be either standalone COM radios or
integrated into one or more of the navigators.
(4) GAD 27 or TCW IBBS (ref AML STC #SA04400NY) is required for 14v airframes with EIS. GAD 27
may optionally be installed on both 14 and 28 -volt aircraft to enable the landing and/or taxi light “wig
wag” feature.
(5) A GTS 8XX traffic system cannot be interfaced to the GDU if a GNX 375 is installed.
(6) If a non-Garmin autopilot is installed, only one external navigator (GPS and/or VHF) can be
connected to G3X. A second navigator, if installed, must use a dedicated CDI and cannot interface to
G3X.
(7) The GAD 29B/29D is only required when the standalone MFD is installed with a G5 and GPS
navigator. If no G5 is installed, the MFD and GPS navigator communicate only via RS-232.
(8) The CAN bus interface to the audio panel is only applicable for a GMA 245R.
GDU 232 Ports:
GDUs have six RS-232 ports. Except as noted below, the ports can be connected to any compatible
LRU. The 232-architecture shown above is only an example configuration.
The port on the P4x01 connector is only compatible with the GEA 24(B). The five ports on P4x02 can be
configured for any supported interface.
When two external navigators are connected, the #1 Nav must be connected to a lower numbered RS-
232 port on the MFD, and the #2 Nav connected to a higher numbered port on the MFD.
If both SXM and ADS-B In are desired in a fully optioned standalone MFD installation (MFD, EIS, and
dual Garmin navigators), a GDL 52R should be used for 232 port availability considerations (the 52R
sends both SXM and FIS-B/TIS-B on one RS-232 bus). Note however that the GDL 5xR is not
compatible with the GTN, so if ADS-B traffic & weather display is desired on both G3X and GTN it must
be sourced from a GNX 375 or GTX 345() per Note 2 (alternatively, the GTN could use GDL 88 or GDL
69, but these are incompatible with G3X).

Page 21
Table 2-3 – G3X Touch and Supporting Equipment
STANDARD/
EQUIPMENT SUPPLIER QTY
OPTIONAL
1, 2, 3 or
GDU 4X0 Garmin Standard
4
GSU 25D Garmin 1 Standard (PFD installations)
GMU 11 Garmin 1 Standard (PFD installations)
GTP 59 Garmin 1 Standard (PFD installations)
GAD 27 Garmin 1 Standard/Optional*
GPS Antenna
Garmin 1 Optional
(011-04036-00 or -10)
GAD 29B/29D Garmin 1 Optional
GDL 5XR Garmin 1 Optional
GEA 24(B) Garmin 1 Optional
GTR 20 Garmin 1 or 2 Optional
GTR 200B Garmin 1 or 2 Optional
GMA 245R Garmin 1 Optional
GAP 26 Garmin 1 Optional
*Reference Section 2.1.7 for applicability.
2.4 Electrical Power Distribution

Electrical load information for the G3X Touch EFIS system LRUs is provided below in Table 2-4.
Appendix A of this document contains details specific to the load changes for the specific aircraft
installation.
Table 2-4 – LRU Current Draw
LRU Current Draw – Maximum Amps
14V System 28V System
Typical Max Typical Max
GAD 27 0.1A 0.1A N/A N/A
GAD 29B/29D 0.1A 0.2A 0.1A 0.1A
GDL 50R 0.1A 0.3A 0.1A 0.1A
GDL 51R 0.1A 0.2A 0.1A 0.1A
GDL 52R 0.2A 0.3A 0.1A 0.2A
GDU 460 1.0A 2.0A 0.5A 1.0A
GDU 470 0.6A 1.3A 0.4A 0.7A
GEA 24(B) 0.2A 0.4A 0.1A 0.2A
GSU 25D, 0.25A 0.35A 0.125A 0.175A
GMU11, GTP 59
GTR 20 3.0A 7.5A 1.4A 3.75A
GTR 200B 3.0A 7.5A 1.4A 3.75A
GMA 245R 0.32A 1.11A 0.18A 0.87A
GAP 26 8.5A 12.0A 4.25A 6.0A

Page 22
3. G3X CONTROL & OPERATION
The Garmin G3X Touch EFIS is intended for Part 23 aircraft covered by the AML STC # SA01899WI.
The following is an overview of G3X Touch panel-mounted units and display features that are provided by
the G3X Touch EFIS.
3.1 GDU 4X0 Softkeys/Features and Control

The GDU 4X0 does not have a power button and will turn ON when power is applied to the aircraft. G3X
Touch remote-mounted LRUs also do not have dedicated power buttons but will turn ON when battery
power is applied to the aircraft or the dedicated bus power (avionics power) is applied. The G3X GDU has
the following controls as shown in Figure 3-1:
• Dual Concentric Knobs – Control knobs that can be used to scroll and select through various
options on the display. Pressing the knob acts as an enter or selection of the currently highlighted
information. The function of each knob on the lower bezel is context sensitive and is identified on
the screen just above the associated knob. Reference Section 3.2.2.1 for using the GDU knob in
configuration mode.
• Menu Button – Used to enter configuration or configuration/diagnostic mode. Reference Garmin
G3X Touch EFIS Part 23 AML STC Installation Manual (190-02472-01) for specific functions
covered in various pages in configuration mode. In normal mode, pressing the MENU button once
brings up the “PFD options” and twice will bring up the “Main Menu”.
• Back Button – Used to return to a previous section/page.
• Direct to – Not used in configuration mode.
• NRST Button – Used in conjunction with the MENU button to enter diagnostic mode or with
MENU and BACK buttons to reboot the GDU. No other functions in configuration mode.
• Photocell – The photocell may be configured to be used by the display to automatically adjust
the display backlighting in reference to ambient light conditions.
• SD Card Slot – A card slot in the display that accepts standard SD cards. The following list
shows the tasks that can be performed via the SD card slot with an SD card installed:
o Update databases
o Software updates
o Datalogging
o Screenshots
o Back up Configuration Files

Page 23
PHOTOCELL
SD CARD SLOT
Figure 3-1 – GDU Features and Controls
KNOB Nearest DIRECT TO MENU BACK KNOB

(NRST)
3.1.1 GDU Reboot

• To reboot GDU without turning off aircraft power, simultaneously and momentarily press the
BACK, MENU and NRST buttons. If the GDU is in configuration mode, it will reboot to normal
mode.
• In configuration mode the GDU may be rebooted back to normal mode by selecting the “Save
and Reboot” page.
3.2 Display Modes
3.2.1 Normal Display Mode

PFD: Two PFD display formats are available in normal mode and controlled by the split/full touch field on
the upper portion of the display. Refer to Figure 3-2 and Figure 3-3:
• Full display – occupies the entire width of the display
• Split format – 50/50 percent display of PFD instrumentation and a Multi-function pane/window, or
a 20/40/40 percent display when the engine bar is present.
The location of the split/full button and the format to be displayed at power up are configured in the
Display Configuration page.

Page 24
Figure 3-2 – Split/Full Format Buttons - GDU 460
Figure 3-3 – Split/Full Format Buttons - GDU 470

The location of the split/full button and the format to be displayed at start up, are configured in the Display
Configuration page.
Figure 3-4 – Normal Mode, Full Format – PFD w/ EIS (Example)

Page 25
Figure 3-5 – Normal Mode, Split Format – PFD W/ EIS (Example)
MFD: provides a multi-function area with various pages and EIS if configured. The display on a 7” GDU
470 when configured as an MFD does not have split format functionality in normal mode but is available
in reversionary mode if the PFD fails. In its place the button is used to toggle between MFD and backup
PFD functionality.

Page 26
Figure 3-6 – Normal Mode, Full – MFD with EIS (Example)
3.2.1.1 Reversionary Mode

In a multiple display installation, a reversionary display mode is supported in the event of GDU failure.
When at least two GDUs are installed, one as PFD and the other as an MFD, the system will
automatically revert the functioning GDU to a reversionary format in the event of a GDU failure. In the
reversionary mode, primary flight information, radio tuning information and EIS (if installed) are displayed
on the remaining GDU.
3.2.2 Configuration Mode Overview

Throughout this document, references are made to the GDUs being in configuration mode. The
configuration mode exists to provide the avionics technician with a means of configuring, checking, and
calibrating various G3X Touch system.
To enter configuration mode:
1. Hold down the “MENU” key on the GDU 4X0 while applying power to the aircraft, until the display
shows “Configuration Mode" text.
Page 27
2. Use the “Move Selector” knob or by touching the display panel to make selections and changes.
3. After all configuration changes have been made, use the “Save & Reboot” page to save all
changes and return to normal mode.
NOTE
For a complete description and breakdown of each Configuration Mode page, refer to the G3X
Touch EFIS Part 23 AML STC Installation Manual (190-02472-01).
3.2.2.1 GDU Knob

The GDU knob has dual concentric knobs; a small inner and a larger outer. GDU 460 has two knobs, one
on each side of the lower section, while GDU 470 has one on the right side of the lower section of the
GDU. The function of each knob on the lower bezel is context sensitive and is identified on the screen just
above the associated knob. If both inner and outer knobs have the same function, the function will be
displayed on the screen above the knob; for example, “Move Selector”, “Scroll List”, etc. may be
displayed. If the inner and outer knobs have the different functions that would be displayed on the screen.
As shown below in Figure 3-7, the outer knob is used to select a tab and the inner knob is used to scroll
down a list.
Figure 3-7 – GDU Knob Function Example

To cycle through different configuration pages:
To scroll to a particular page: Rotate either the large outer or small inner knob or use the touch
panel.
To select a page: Press/push the inner knob or touch the page on the display.
To navigate between different tabs on a page: Rotate the large outer knob or use the touch panel.
To scroll down a list/data field in a tab: Rotate the inner knob or use the touch panel.
To select a data field: Press/push the inner knob or use the touch panel.
3.2.2.2 Configuration Data Entry

To change the contents of a highlighted data field, use the either the pop-up keyboard, pop-up keypad,
pop-up slider bar or touch panel as applicable.
Figure 3-8 – Data Entry Options (Examples)

Page 28
3.2.2.3 System Status Indicators
The “System Information” page in the configuration mode of the GDU 4X0 PFD has a “Devices Online”
tab that reports the status of installed LRU’s and their currently installed software part numbers and
versions. The icon/checkbox next to each LRU reports a green checkmark, a ‘red x’ or blank checkbox to
indicate the status of each LRU as described in Table 3-1.
Table 3-1 – LRU Status Indicator Symbols
INDICATION LRU CONDITION

The LRU is online and reports the item located next to the
indicator box is communicating.
The LRU is online, and reports the item located next to the
indicator box is not communicating, a fault, warning, or
error has been detected.
The LRU is not online.
3.2.2.4 Configuration Mode Navigation

Using the PFD knob and data entry options as described in Sections 3.2.2.1 and 3.2.2.2 a user can
navigate through different pages and page groups in the Configuration Mode. Reference the Garmin G3X
Touch EFIS Part 23 AML STC Installation Manual (190-02472-01) on how to make configuration
changes.
NOTE
Some configuration pages appear only when certain optional LRUs are installed and configured.
Figure 3-9 – Configuration Mode Pages

Page 29
3.2.3 Configuration/Diagnostic Mode
Troubleshooting and diagnostic information for CAN bus can be viewed in Configuration/Diagnostic
mode. For CAN troubleshooting information, reference section 5.2.
To enter configuration/diagnostic mode:
1. Simultaneously hold down the “MENU” and “NRST” key on the GDU 4X0 while applying power to
the aircraft, until the “Configuration/diagnostic Mode” text is displayed on the screen.
2. Use the “Move Selector” knob or touch panel to make selections as necessary.
3. After all configuration changes have been made, use the “Save & Reboot” page to save all
changes and return to normal mode.

Page 30
4.2 Servicing Information
G3X Touch EFIS LRUs maintenance is ‘on condition’ only. No component-level overhaul is required for
the G3X Touch EFIS Part 23 AML STC installation. See section 6 for equipment removal and installation.
4.2.1 On-condition Servicing
‘On Condition’ replacement and/or servicing should occur when an item exhibits conditions, symptoms,
and/or abnormalities defined in Section 5 of this manual. Replacement and/or servicing should be made
only after the technician troubleshoots the system to the extent determined necessary by using the
guidance in this manual along with common avionics maintenance practices.
NOTE
It is impossible to provide guidance for every conceivable failure scenario within the scope of this manual.
Every effort has been made to provide comprehensive guidance for possible failures. The information in
this document should always be combined with sound aviation maintenance practices and a thorough
knowledge of the system. Use sound avionics maintenance practices when working around or on G3X
equipment.
NOTE
After replacing or servicing electrical components near the GMU 11 magnetometer, the Magnetometer
Interference Test (reference Section 5) and Magnetometer Calibration Procedure (reference Section 7)
must be performed.
The remainder of this document is organized in the following fashion:

• Section 4.3 lists maintenance requirements related to the G3X system.
• Section 5 provides troubleshooting guidance
• Section 6 gives instructions regarding the removal and replacement of physical G3X Touch EFIS
equipment and parts.
• Section 7 gives configuration and testing instructions to be accomplished if G3X Touch EFIS
equipment or parts are removed or replaced.
• Section 8 specifies system return-to-service procedure.
4.2.2 Required Tools
The following tools are needed to perform maintenance tasks on G3X equipment:
• SanDisk brand SD card, 8GB or smaller
• Calibrated Milliohm meter with Kelvin probes or equivalent
• Calibrated digital level
• Calibrated air data test set (pitot/static ramp tester)
• Calibrated VHF NAV/COM/ILS ramp tester or equivalent
• Outdoor line-of-site to GPS satellite signals or GPS indoor repeater
• Headset/microphone
• Ground Power Unit
• Calibrated torque wrench
• Standard sockets & wrenches
• 3/32” Hex tool
4.3 Maintenance Intervals

Table 4-1 shows systems and items installed by this STC, which must undergo tests or checks at specific
intervals.
Page 32
Table 4-1 – Maintenance Intervals
Manual
Item Description/Procedure Interval
Section No.
Complete Visual Inspection of all

12 Calendar Months
G3X Touch System Visual installed G3X system LRUs and wiring
4.4 (During annual
Inspections harnesses must be performed to ensure
inspection)
continued integrity of the installation.
Perform an electrical bonding check of Every 2000 flight hours
Electrical Bonding Check the G3X Touch system LRUs in 4.5 or 10 years, whichever
accordance with Section 4.5. comes first
12 Calendar Months
Perform a pneumatic line drain check if
Pneumatic Drain Check 4.8 (During annual
applicable
inspection)
GDU 4X0 (Qty. 1, 2, 3 or 4) Removal & Replacement 6.1 On Condition
Removal & Replacement 6.2 On Condition
GSU 25D (ADAHRS) When available (5-year
AHRS Magnetic Field Model Update 4.6
update cycle)
GMU 11 Removal & Replacement 6.3 On Condition
GTP 59
Special Inspection Requirements 4.7 On Condition
GAD 27 Removal & Replacement 6.5 On Condition
GEA 24(B) Removal & Replacement 6.6 On Condition
GAD 29B/29D Removal & Replacement 6.7 On Condition
GDL 5XR Removal & Replacement 6.8 On Condition
GTR 20 Removal & Replacement 6.10 On Condition
GTR 200B Removal & Replacement 6.11 On Condition
GMA 245R Removal & Replacement 6.12 On Condition
GAP 26 Removal & Replacement 6.13 On Condition
EIS Annunciators
Lamp Check (If installed) 8.12.4 On Condition
Check for and troubleshoot any alerts
G3X Alerts provided in the alert window per the 5 On Condition
referenced manual section
GPS Antenna Removal & Replacement 6.9 On Condition
G3X Accessories
GDU Configuration Module
Removal & Replacement 6.1.1 On Condition
(Qty 1)
G3X Lightning Protection
Lightning Strike to Antenna Inspect the GTP 59 and surrounding
installation 4.7 On Condition
Actual or Suspected

Page 33
Manual
Item Description/Procedure Interval
Section No.
Engine/Airframe Sensors
Oil Pressure
Oil Temperature
Manifold Pressure
Removal & Replacement: 6.6.1 On Condition
Carb Air Temp
Fuel Pressure
Fuel Flow

Page 34
4.4 Visual Inspection
Operation of the G3X Touch system is not permitted unless a visual inspection, as described in this
section, has been completed within the preceding 12 calendar months. Check for corrosion, damage, or
other defects for each of the G3X Touch LRUs. Replace any damaged parts as required. Inspection may
require the temporary removal of a unit or units to gain access to connectors. Follow guidance in Section
6 for equipment removal and replacement.
Conduct the following visual inspection of the G3X Touch EFIS system LRUs and associated wiring
harnesses to ensure installation integrity:
1. Inspect all units for security of attachment, including visual inspection of brackets and other
supporting structure attaching all units to the airframe.
2. Inspect all switches, annunciators, knobs, and buttons for legibility.
3. Inspect displays for legibility and acceptable brightness. Reference Section 5.3.1.
4. Visually inspect each unit’s wiring (including electrical bonding straps), overbraid, and connectors
for chafing, deterioration, damage, or wear.
5. Visually check for any signs of corrosion.
4.4.1 Aluminum Foil Tape (Non-metallic Aircraft Only)

Any aluminum foil tape if used in the G3X Touch installation for grounding of a GSU 25D, GEA 24(B),
GAD 29B/29D or GAD 27, (refer to Appendix A of this document) must be inspected every 12 calendar
months.
The inspection must verify that the foil tape is not torn, damaged, or showing signs of corrosion. If any of
these conditions are found, the tape must be replaced in accordance with Section 4 of G3X Touch EFIS
Part 23 AML STC Installation Manual.
4.5 Electrical Bonding Test
G3X Touch EFIS LRU electrical bonding must be checked every 2,000 flight hours or 10 years, whichever
occurs first.
4.5.1 Requirements
• Disconnect any cables and connectors normally attached to the LRU.
• Resistance must be measured from a bare metal portion of the LRU to an airframe grounding
location.
The airframe grounding location should be as close to the LRU as possible, unless otherwise noted in
Table 4-2.
4.5.2 Test Equipment

Calibrated 4 wire Milliohm meter and Kelvin probes are required for this test.
4.5.3 Electrical Bonding Test Procedures.

• Using a calibrated milliohm meter and Kelvin probes, measure the resistance of each G3X Touch
LRU between the locations noted in
• Table 4-2, and record the result of each installed LRU. Some equipment on the list are optional
and may not be installed.
• Ensure the resistance does not exceed 10 milliohms for equipment in Table 4-2 except GAP 26
which should not exceed 20 milliohms.
• If the measured resistance is greater than allowed, bonding must be improved to meet applicable
requirements for a new installation in accordance with Section 4 of G3X Touch EFIS Part 23 AML
STC Installation Manual (190-02472-01).

Page 35
Table 4-2 – Electrical Bonding Procedure
Unit Measurement Location (3) Result
(milliohm)
GDU 4X0 (PFD) J4X02 backshell to ground stud (2) mΩ
GDU 4X0 (MFD) (if J4X02 backshell to ground stud (2) mΩ
installed)
GSU 25D (1) Chassis mounting screw to adjacent aircraft ground mΩ
P251 backshell to ground stud (2) mΩ
GMU 11 P111 backshell to ground stud (2) mΩ
GAD 29B/29D Chassis mounting screw to adjacent aircraft ground mΩ
GAD 27 Chassis mounting screw to adjacent aircraft ground mΩ
GEA 24(B) Chassis mounting screw to adjacent aircraft ground mΩ
GDL 5XR P5X1 backshell to ground stud (2) mΩ
GTR 20 Chassis mounting screw to adjacent aircraft ground mΩ
GTR 200B Rack Rack/chassis mounting screw to adjacent aircraft mΩ
ground
GMA 245R Chassis mounting screw to adjacent aircraft ground mΩ
GAP 26 Mount tube bracket screw to adjacent aircraft ground mΩ
Notes:
(1) For remote mounted – it is bonded via the chassis mounting to aircraft ground.
For GDU-mounted – it is bonded via bonding strap to a ground stud
(2) This is the ground stud that the LRU bonding strap is connected to.
(3) For remote LRUs bonded to the back of the instrument panel via an installed aluminum foil ground plane,
the bonding measurement must be taken between the remote LRU and the instrument panel.
4.6 GSU 25D Earth Magnetic Field Updates

The GSU 25D utilizes an Earth magnetic field model which is updated once every five years. The IGRF
(International Geomagnetic Reference Field) update is expected to be available from Garmin in July 2020
and every five years thereafter, as long as the GSU 25D remains a Garmin-supported product.
The IGRF model is automatically updated with the navigation database for G3X software versions 9.15
and later. The G3X system alerts the operator that the magnetic field database is out of date by issuing
the message "AHRS IGRF data out of date".
4.7 Special Inspection Requirements

After a suspected lighting strike, the following actions must be performed for the specific LRU.
GTP 59 Temperature Probe
Inspect the GTP 59 temperature probe for signs of lightning damage. Check the self-sealing washer (P/N
212-00026-00) used on the probe tip outside of the aircraft for any evidence of melting or lack of seal.
Replace the washer if damaged. If there is evidence of lightning strike to the GTP 59 temperature probe
or any lightning damage, replace the probe.
Tube-and-fabric aircraft must replace the GTP 59 bond strap (if installed) in accordance with Section 4 of
the G3X Touch EFIS Part 23 AML STC Installation Manual (190-02472-01).
G3X Equipment
All G3X equipment should be checked per Section 7. If equipment is not functioning correctly,
troubleshoot using information in Section 5. Contact Garmin Product Support before replacing G3X LRUs
to verify all troubleshooting options were exhausted.

Page 36
4.8 Pneumatic Line Drain Check (If installed)
Check of the pneumatic line drain to verify positive drainage must be performed every twelve months or
during annual inspection, whichever comes first.
• Locate the pitot/static/AOA line drain if installed. Refer to the location information recorded in
APPENDIX A of this document and maintained with the aircraft records.
• Open the drain plug to empty any moisture in the system.
• Reinstall the drain plug.
• Perform applicable checkout procedures in Section 8 (8.13.1 and 8.19.2).

Page 37
5. TROUBLESHOOTING
This section provides instructions and guidance for G3X Touch EFIS troubleshooting.
Troubleshoot the G3X Touch EFIS by first identifying, then isolating the specific failure to the responsible
LRU. There are several indications the G3X Touch EFIS presents to the pilot or technician, showing overall
system condition. A course of action should be determined based on the information presented on the
display. This section shows possible scenarios likely to be encountered during normal operation and
provides troubleshooting guidance to the technician to resolve problems. Reference the interconnect
diagrams on the G3X Touch EFIS Part 23 AML STC Installation Manual (190-02472-01) and retained with
aircraft permanent records while troubleshooting the G3X system.
In this manual, the term ‘Red-X’ refers to a red “X” that appears on different areas of the display to indicate
the failure of that specific function.
IMPORTANT
Sections 6, 7 and 8 provide detailed instructions on equipment removal, replacement, configuration, and
return-to-service testing. Anytime a G3X Touch component or LRU is removed, swapped, or replaced, the
technician must follow the procedures given in Sections 6, 7, and 8 to ensure proper operation of the system.
Refer to the G3X Touch Pilot’s Guide for Certified Aircraft (190-02472-00) for a complete listing of System
Status Messages.
For additional assistance, contact a G3X Touch Dealer, or Garmin Aviation Product Support at US Toll Free
Number 1-888-606-5482, or US 1-913-397-8200.
NOTE
Any warning message indicated on the “Messages” field or anywhere on the display while on-
ground should be investigated and resolved before flight.
NOTE
The information in this section is for troubleshooting use only and does not supersede any
approved Maintenance or Installation Manual instructions.
5.1 General Troubleshooting

1. Review the airframe logbook to verify if any G3X Touch EFIS or other avionics/electrical
maintenance had been performed recently that may have contributed to the failure.
2. Check for loose wire terminals on the circuit breaker connections on the power wire(s) causing
intermittent power connections. Also, check for intermittent circuit breakers.
3. Connect an auxiliary ground power unit and apply power to the aircraft.
4. Turn ON the G3X Touch EFIS and record the system software level on the GDU start up page.
5. After the system is initialized, note any Red-X’s on the displays, ALERT messages and Red-X’s on
the GDU.
If the failure cannot be verified, proceed to the following physical inspection.
1. Turn off the G3X Touch EFIS and remove the interior panels (as required) to gain access to the
ADAHRS. Inspect the physical installation of the affected LRU.
2. Check that the connectors are fully seated, and that the jack screw connectors are fully tightened on
both sides of the affected LRU’s connector.
3. Check for a loose wire harness that could move around during flight. This condition may cause the
wire to pull on or vibrate the connector, creating intermittent connections.
4. Ensure the affected LRU is mounted securely. Check the tightness of the mounting hardware.

Page 38
5. Look in the vicinity of the affected LRU for any heavy objects that may not be securely fastened to
the structure, inducing vibration in the ADAHRS.
6. Look for evidence of water or fluid contamination in the area around the affected LRU.
7. Disconnect the affected LRU’s connector(s) and check for bent pins.
8. Inspect the wire harness clamp on the rear of the connector to verify that it is not too tight and
smashing/shorting the wires. If the wire clamp is installed upside down, it has sharp edges that can
cut into the wires. Verify the presence of protective wire wrap between the wires and the clamp.
If the condition is not resolved by following the preceding instructions, use data in this section before
contacting Garmin Product Support for additional assistance. A Garmin Field Service Engineer may ask the
technician to download the fault logs via an SD card and email the logs back to Garmin to help determine the
root cause.
5.2 CAN Bus Network Troubleshooting

If communication problems between LRUs are suspected, the CAN bus wiring and arrangement of devices
on the network should be examined.
1. Review the status LED of devices on the CAN bus. The GAD 29B/29D, GEA 24(B), GSU 25D, GAD
27, GTR 20 and GSA 28 (if GFC 500 is installed) have an LED on their outer cases that indicates
the LRU’s current status. The status indications are shown in Table 5-1:
Table 5-1 – Status LED Indications
LED Indication Description
No light No power
Steady Green ON, but not communicating via the CAN Bus
Flashing Green ON, and communicating via CAN Bus
Red Hardware Fault
Alternating Green/Red CAN Bus network error, two similar devices are
configured with the same unit ID
2. Use the guidance in Table 5-2 to troubleshoot LED indications.

Table 5-2 – LED Indications Recommended Action
LED Indication Description Recommended Action
No light No power Verify the circuit breaker, power and ground wiring
between the circuit breaker and the affected unit.
Replace the unit if power is available to the unit.
Contact Garmin Product Support before replacing unit to
determine all troubleshooting options have been completed.
Steady Green ON, but not Inspect and verify the CAN Bus wiring between the G3X
communicating via the Touch and the unit
CAN Bus
Flashing Green ON, and communicating None.
via CAN Bus
Red Hardware Fault Contact Garmin Product Support (unit may need to be
replaced)
Alternating CAN Bus network error, verify the Unit ID strapping on the G3X units. Reference
Green/Red two similar devices are the G3X Touch EFIS Part 23 AML STC Installation
configured with the Manual (190-02472-01) wiring diagrams for strapping
same unit ID details

Page 39
3. Ensure proper installation of the CAN bus and that the following guidance was adhered to during
installation:
• The CAN bus backbone must be a single linear path with exactly two distinct ends. CAN bus
connections must be “daisy-chained” from device to device. Avoid “star” and “Y” topologies, and
do not use a hub device. Reference Figure 5-1.
Figure 5-1 – Incorrect CAN Bus Topographies

• The overall length of the bus must not exceed 100 feet.
o Ensure any existing part number M27500 wire if retained for the CAN bus wiring does not
exceed 60 feet in overall length. Approved CAN wiring P/N GF120-24CANB-1/GF120T-
24CANB (GigaFlight Connectivity) and P/N CAN24TST120(CIT) (Carlisle IT) may have
lengths in excess of sixty feet.
• Do not connect more than one device to the CAN bus backbone at the same point. Instead,
daisy-chain the CAN bus backbone from one device to the next.
• Observe proper wiring, shielding, and grounding requirements as described above.
• Terminate the CAN bus at the two extreme ends of the bus, as described above.
• When adding a new device to the CAN bus, evaluate proposed modifications to the CAN bus
wiring connections to ensure compliance with all above requirements and the G3X Touch EFIS
Part 23 AML STC Installation Manual (190-02472-01).
4. Ensure the CAN bus is terminated in only two locations, and only at the extreme ends of the CAN
bus.
Figure 5-2 – Correct CAN Bus Wiring Example and Node Connections
5. Ensure the 15 ohm resistors on the CAN bus inputs to the G5 are correctly installed. If the G5 is
also at one end of the CAN bus, verify that the 120 ohm terminator resistor is correctly installed in
relation to the 15 ohm resistors. Reference the CAN Bus Termination section of the Garmin G5
Electronic Flight Instrument Part 23 AML STC Installation Manual (190-01112-10) for more
information.
6. With power removed, remove a connector from one of the devices that is not located at either of the
extreme ends of the CAN bus.
NOTE
Do not perform this test on the G5 (if installed as a standby flight display).

Page 40
a. Using an ohm meter, verify that the resistance between the CAN HI and CAN LO pins on the
connector is 60 ohms. This will verify that the CAN backbone is properly terminated at each
end (two 120 ohm terminating resistors in parallel).
b. A resistance of 120 ohms indicates that one of the two required CAN terminations is
missing.
c. A resistance of 40 ohms or less indicates that too many terminations are installed.
d. Verify that the CAN HI and CAN LO signals are not shorted to ground (this can happen
when shielded wire is installed incorrectly).
e. Measure the resistance between CAN HI and shield ground, and CAN LO and shield
ground. Verify resistance is several hundred kilohms (KΩ) or greater.
7. Verify that the CAN HI and CAN LO signals are not swapped or open-circuited at any LRU
connector.
8. Power the G3X system and with GDUs in configuration/diagnostic mode, reference section 3.2.3.
• Using Touch Panel or a Move Selector Knob to select and view the System Information
Page.
• Scroll the Device List box and the select each device and verify the value displayed for
Network Error Rate is a steady 0% (Figure 5-3).Also verify the other network counts values
listed on Table 5-3.
Figure 5-3 – Network Error Rate (Configuration/Diagnostic Mode)
NOTE
CAN issue might not be with the unit reporting CAN errors but could be anywhere in the CAN bus
system. Table 5-3 is used as a guidance for determining if CAN bus is causing errors while
troubleshooting unit or system errors.
Table 5-3 – CAN Network Error Values (Configuration/Diagnostic Mode)

CAN INFO
DESCRIPTION VALUE POSSIBLE CAUSE ACTION
Troubleshoot wiring and connection
Network Error Rate > 0% CAN bus wiring problem
issues that might create CAN errors

Page 41
CAN INFO
DESCRIPTION VALUE POSSIBLE CAUSE ACTION
Increasing ≥ 1 Troubleshoot wiring and connection
Network Tx Warning CAN bus wiring problem
per minute issues that might create CAN errors
Network Rx Warning Increasing ≥ 1 CAN bus wiring problem Troubleshoot wiring and connection
per minute issues that might create CAN errors
Network Error Passive ≥2 CAN bus wiring problem Troubleshoot wiring and connection
Network Pass Off ≥2 CAN bus wiring problem Troubleshoot wiring and connection
9. Power up only the PFD display and one CAN device at a time and verify the connection quality for
each device. Sometimes a device will only communicate with PFD when it is the only powered
device on the CAN bus, if one or more of the above issues is present. Evaluating each CAN device
in turn can help narrow down a problem.
5.3 GDU 4X0
5.3.1 Display Legibility

Degradation of the GDU 4X0 LCD or backlight may reduce legibility. Backlight brightness may also be
adversely affected by issues with an external lighting bus or the photocells in the GDU bezel. If display
elements are not easily legible under all lighting conditions encountered in the cockpit including direct
sunlight, verify that the backlight can be adjusted to an acceptable brightness level via the manual dimming
control in the PFD menu. If manual dimming adjustment results in acceptable legibility, troubleshoot the
external lighting bus input for incorrect input voltage levels. Verify photocell lenses are clean and
unobstructed. Backlight dimming configuration for lighting bus or photocell should be verified in
Configuration Mode and may be adjusted as needed. Reference the G3X Touch EFIS Part 23 AML STC
Installation Manual (190-02472-01) for further detail.
If the above steps do not result in acceptable display legibility the GDU may need to be replaced. Contact
Garmin Product Support for more information.
5.3.2 SD Card Slot

A stuck or sticking SD card issue can sometimes be caused by the card thickness variability (especially if
there is more than one label on the card). This is usually caused by the card sticking in the overlay opening,
not by the card sticking to the socket inside the unit. Try another card (without a label if possible) to confirm
the problem before returning. If the second card sticks, the SD socket board inside the unit may be
misaligned with the overlay and the GDU will require repair. If the thickness of the card was the cause, see if
more than one label was on the card. If the labels weren’t the cause, determine what brand of SD card was
being used (Garmin recommends using SanDisk® brand cards with a maximum capacity of 8 GB).
Replace any corrupted SD card that might be causing an issue.
5.3.3 Data Logging

Data logging on the G3X Touch GDU may be used to help troubleshoot issues. Operational data is gathered
from the G3X Touch during flight or on ground and is stored in *.csv log files on the SD card (if installed and
enabled).
5.3.4 Unit Communication Error Messages (Dual GDU Installations)

Error messages occur if there is a mismatch in GDU software versions. If this occurs, the GDU’s will not
communicate with each other, and a software mismatch message will be reported on the “Messages” page.

Page 42
Use the touch panel to select the yellow “Messages” field or select Main Menu > Tools >
Messages, to view the error messages. Ensure both displays are running the same software version to clear
the issue. Unit communication error related messages and recommended actions are shown on Table 5-4.
Table 5-4 – Unit Communication Error Messages (Dual GDU Installations)

Failure Message Possible Cause Recommended Action
The two GDU displays are Update software to latest on the GDU
GDU software version
using incompatible software with incorrect software version
mismatch
versions
State of a GDU's mode pins Check for loose connections and
was detected to have changed. reference the G3X Touch EFIS Part 23
“[UNIT]” network address
AML STC Installation Manual (190-
changed”
02472-01) for information on GDU
mode pin connections
“GDU COMM ERROR – Indicates that more than one Verify and correct GDU mode pin
CHECK GDU WIRING” GDU is configured to be the connections per the G3X Touch EFIS
same unit type (e.g. two Part 23 AML STC Installation Manual
displays are configured as (190-02472-01)
PFD)
[Navigation/Terrain/Obstacle] Indicates that a required Update databases as required.

Database Missing database is missing on the
specified GDU display.
[Navigation/Terrain/Obstacle] Indicates that the GDU displays Update the databases in all GDU
Database Mismatch have different versions of the displays to the same cycle number.
specified database.
5.3.5 GDU Reboot During Engine Start in a 14-volt Aircraft

If the GDU display inadvertently reboots during engine start, troubleshoot aircraft electrical system for
anything that might result in low bus voltage during engine start, reference Table 5-5 for recommended
actions.
NOTE
Flickering and dimming during engine start are not considered rebooting. The display has to turn
off and initialize again (generally requiring 20-30 seconds) to be considered a reboot.

Page 43
Table 5-5 – GDU Reboot During Engine Start
Symptom Possible Cause Recommended Action
Low bus voltage Troubleshoot aircraft electrical system for:

 insufficient battery capacity
 poor starter performance
 insufficient wire gauge in starter circuit
 high resistance through wire connections, circuit
breakers, or solenoids
 other issues in the starter circuit and primary power
distribution system
GDU display reboots Verify that the Electrical Load Analysis and Battery
during engine start (14-volt Capacity Analysis have been performed with
aircraft only) satisfactory results per the G3X Touch EFIS Part 23
AML STC Installation Manual (190-02472-01) Sections
3.6.1 and 3.6.2.
Install a GAD 27 or TCW IBBS

If troubleshooting does not reveal any anomalies in the
aircraft’s battery or electrical system, a GAD 27 or TCW
IBBS may be optionally installed per the G3X Touch
EFIS Part 23 AML STC Installation Manual (190-02472-
01) to address the issue
5.4 GSU 25D ADAHRS and GMU 11 Magnetometer Troubleshooting
5.4.1 Air Data Troubleshooting

Under normal operating conditions, the ADAHRS provides the following air data information:
• Total Air Temperature is measured
• Outside Air Temperature (OAT) – A valid OAT will display a number
• Indicated Airspeed (IAS)
• True Airspeed (TAS) – A valid OAT value is required to calculate TAS
• Barometric Altitude
• Density Altitude
• Pressure Altitude
• Static Pressure
• Differential Pressure
NOTE
TAS information can only be displayed at speeds greater than 20 Knots (TAS is invalid
when the aircraft is sitting still, or if no OAT probe is connected).
Reference Table 5-6 for troubleshooting guidance.

Page 44
Table 5-6 – ADAHRS and Magnetometer Troubleshooting
Symptom or Failure
Possible Cause Recommended Action
Message
Improper installation of the Verify GMU 11 and GSU 25D mounting
GMU 11 and/or GSU 25D locations are in accordance with the G3X
Touch EFIS Part 23 AML STC Installation
Manual (190-02472-01)
Excessive magnetic Perform the magnetic interference test in
interference (determine if any Section 5.4.4
new equipment has been
installed on the aircraft near the
magnetometer)
Magnetic anomaly (If detected, If this error shows up repeatedly, conduct the
Heading failure (Red X’d and the aircraft is determined to magnetic interference check in Section 5.4.4
intermittently or steady) be stationary, the value of the
heading output is frozen. When
either the aircraft is determined
to be no longer stationary or the
magnetic anomaly ceases,
heading will be unfrozen and
determined as useable. In this
context, the aircraft is considered
to be stationary when its yaw
rate is less than 1.0
degrees/second and all other
angular rate and acceleration
values are sufficiently small.
(moving or shaking the wings or
tail for example can cause a
Red-X to be displayed).
Communication lost between Inspect GMU 11 wiring
Magnetic heading not GSU 25D and GMU 11 Ensure the GMU 11 installation is in
present accordance with the G3X Touch EFIS Part
23 AML STC Installation Manual (190-02472-
01)
Communication lost between Inspect GMU 11 wiring
GSU 25D and GMU 11
AHRS not receiving Ensure the GMU 11 installation is in
magnetometer data accordance with the G3X Touch EFIS Part
23 AML STC Installation Manual (190-02472-
01)
Attitude failure ADAHRS and/or Perform pitch/roll compensation offset and
Magnetometer not calibrated magnetometer calibration as per Section 7
(Red X’d intermittently or
steady) ADAHRS unable to compute Replace GSU 25D
valid attitude data due to
insufficient or invalid sensor Contact Garmin Product Support before replacing
information unit to determine all troubleshooting options have
been completed.
Both OAT and TAS OAT is unavailable  Inspect GTP 59 OAT probe wiring and
failure connection for faults.
 Replace the GTP 59 OAT probe.
 Inspect GSU 25D wiring and connections
for faults

Page 45
Symptom or Failure
Message
 If the problem persists, replace the GSU
25D with a known good unit
True airspeed being None

measured is too low to be of
TAS has a dashed-out value (e.g. when the aircraft
value is on the ground).If the TAS
indication remains dashed out at
speeds greater than 20 knots
and/or the OAT indication is Red
-X’d continue with recommended
action above for OAT and TAS
failure.
Pressure sensor is out of  Inspect ADAHRS pitot/static plumbing
range (possibly due to integrity.
improper plumbing such as  Inspect pitot/static ports and associated
pitot and static lines equipment.
Airspeed and/or Altitude reversed)  If a periodic altimeter test, performed
failure with properly calibrated static system test
set, indicates that the ADAHRS static
pressure sensor needs to be re-
calibrated, follow the procedures
described in Section 7.2.1.3.
25D with a known good unit
No power to GSU 25D (if  Ensure GSU 25D circuit breaker is not
Heading, Attitude and OAT open.
are also red-x’d)  Inspect wiring and electrical connections
 If problem persists, replace the GSU 25D
with a known good unit.
Pressure sensor is out of  Inspect ADAHRS pitot/static/AOA
range, leakage in pneumatic plumbing integrity.
lines  Inspect pitot/static/AOA ports and
AOA visual or aural associated equipment.
indications are incorrect  Perform the pitot/static/AOA leak checks
in sections 7.2.1 and 8.19.2.
25D with a known good unit.
GSU 25D has failed (installed  Ensure GSU 25D circuit breaker is not
with a G5 or GI 275 standby). open.
 Inspect wiring and electrical connections
 If problem persists, replace the GSU 25D
with a known good unit.
5.4.2 Heading Red-X
Figure 5-4 – Heading Failure Indication

Page 46
If a Red-X (steady or intermittent) or a yellow (degraded) is displayed on the heading (Figure 5-4), use
guidance in Table 5-6 and check the following while the aircraft is on the ground:
1. When taxiing without reliable GPS information, heading performance is susceptible to the presence
of magnetic anomalies (metal buildings, underground steel culverts, steel grates in the ramp, rebar).
Localized sources of interference on the ground may consistently cause a Red-X to be displayed on
the heading in the same spot while taxiing, this is not caused by a failure of the GMU or its
calibration.
2. When the aircraft is taxiing on the ground with a yaw rate of less than 2.5 degrees/second (i.e.,
taxiing essentially in a straight line) GPS track information is used to update heading information.
This logic is applied regardless of magnetic anomaly detection.
5.4.3 Attitude/Heading Failure Troubleshooting

The ADAHRS may not be able to provide valid heading/pitch/roll data for the following reasons:
1. If an “ADAHRS not Calibrated” message is displayed, the external installation configuration
parameters are not calibrated and the ADAHRS pitch/roll compensation offset (Section 7.2.1.1)
and/or Magnetometer calibration (Section 7.2.1) need to be performed. If either of these is not
calibrated, the ADAHRS heading, pitch, and roll may all be flagged as invalid. Calibrate the unit to
the installation.
2. The ADAHRS is unable to compute valid attitude information due to insufficient or invalid sensor
information being provided.
Figure 5-5 – Attitude Failure Indication
If the attitude is failed and shows a Red-X condition, follow the troubleshooting steps in the Section 5.1. If
this does not resolve the issue, use guidance in Table 5-6, before gathering answers to the following
questions. This information may be helpful to the customer, the avionics dealer, or to Garmin Aviation
Product Support in troubleshooting the failure:
1. What specifically was the nature of the failure? Was it a Red-X of only heading, only pitch/roll, or
both?
2. If there was a Red-X of pitch or roll information, did the PFD display the "ADAHRS Align: Keep
Wings Level" message (which is indicative of an ADAHRS reset), or the "Attitude Fail" message
(which is indicative of either ADAHRS invalidating its output, or a communication path failure)?
3. What exactly was the aircraft doing in the two minutes that preceded the failure (taxing on the
ground, flying straight-and-level flight, turning, climbing, etc.)? If the problem occurred on the ground,
was it within 100 feet of a hangar using GPS repeaters?
4. How long did the failure last? Was it brief or sustained? Was it repetitive in nature? If it was
repetitive, about how many times did it happen? Did it happen on more than one day?
5. Was the problem correlated with a specific maneuver or a specific geographic area?
6. Can the problem be repeated reliably?
7. Were any of the following message advisory alerts observed on the display or messages field within
an hour of the occurrence of the problem?

Page 47
• ADAHRS not receiving airspeed
• ADAHRS not receiving any GPS information
• ADAHRS magnetic-field model out of date
• ADAHRS extended operation in no-GPS mode
8. Did the onset of the problem occur shortly after a software upload to the G3X Touch system, or
shortly after a repeat of the magnetometer calibration procedure? Were there any GPS Alert
messages or loss of position lock?

Page 48
5.4.4 Magnetometer Interference Test
NOTE
The Magnetic Interference Test is only required for initial installation verification. This test should also be
repeated to verify all subsequent electrical changes associated with devices within 10 feet of the GMU
magnetometer. Such changes include, but are not limited to, wiring, shielding, or grounding changes to
any light, strobe, beacon, or other electrical device located in the vicinity of the GMU magnetometer unit.
Likewise, this test should also be repeated to verify all subsequent changes to materials within 10 feet of
the GMU magnetometer. Such changes include but are not limited to addition, removal, or modification
of ferrous or electrically conductive materials located in the same wing as a GMU magnetometer unit.
This procedure validates that no electronic device is interfering with the operation of the GMU
magnetometer which directly impacts the determination of attitude and heading by the GSU 25D. The
ADAHRS Unit Orientation and Pitch/Roll Offset Compensation are not required prior to this execution of
this procedure. A sequence of activities to be performed during a magnetometer interference test is
shown in Table 5-7 below. This is an example to help guide a technician through an aircraft’s functions
that may create interference with an installed GMU 11 magnetometer.
CAUTION
The real time readout displayed during the interference test is only valid for the location of the GMU
when the test was initiated. If using this procedure to evaluate multiple mounting locations, the test must
be started over for each location, failure to do so could provide incorrect test results.
1. Power on PFD in configuration mode (Section 3.2.2).
2. Select the Magnetometer Calibration Page.
3. Select Magnetic Interference Test.
4. Ensure that the aircraft has been properly prepared per the on-screen instructions. See Table 5-7 for
a sample test sequence. Press the Start button to begin the test.
Figure 5-6 – Magnetometer Interference Test On-screen Instructions

5. The actions must be carried out as called for in the prepared test sequence. During calibration, a
real-time value is displayed that represents the current magnetic field strength as a percentage of
the maximum limit.

Page 49
Figure 5-7 – Magnetometer Interference Test Progress
NOTE
It is important that all actions are carried out in the order and at the precise elapsed time as specified in
the prepared test sequence.
6. After completing the prepared test sequence, press the Done softkey. Ensure that a PASSED
message appears on the display. The magnetic deviation value is displayed to indicate the pass or
fail margin of the test. Press the Done softkey to return to the Magnetometer Page.
Figure 5-8 – Magnetometer Interference Test Status

Page 50
Table 5-7 – Magnetometer Interference Test Sequence Example
Elapsed Time (From Start of Test) Action
(min:secs)
0:00 Test Begins
0:10 Aileron Full Right
0:20 Aileron Full Left
0:30 Aileron Level
0:40 Elevator Up
0:50 Elevator Down
1:00 Elevator Level
1:20 Rudder Left
1:40 Rudder Right
1:50 Rudder Center
2:00 Flaps Down
2:10 Flaps Up
2:20 Autopilot On
2:30 Autopilot Off
2:40 Electric Trim (GFC 500)
2:50 Landing Gear Up
3:00 Landing Gear Down
3:10 Speed Brake Up
3:20 Speed Brake Down
3:30 Navigation Lights On
3:40 Navigation Lights Off
3:50 Landing Lights On
4:00 Landing Lights Off
4:10 Taxi Lights On
4:20 Taxi Lights Off
4:30 Landing + Taxi Lights On
4:40 Landing + Taxi Lights Off
4:50 Strobes On
5:00 Strobes Off
5:10 Recognition Lights On
5:20 Recognition Lights Off
5:30 All Wing-Tip Lights On (simultaneous)
5:40 All Wing-Tip Lights Off (simultaneous)
5:50 Beacon On
6:00 Beacon Off
6:10 Pitot Heat On
6:20 Pitot Heat Off
6:30 Test Complete

Page 51
If the magnetic interference test fails, the installation should be considered unreliable until the source of
magnetic interference is identified and remedied. The magnetometer interference test must be repeated
until passed. When the magnetometer interference test fails, record the magnetometer maximum deviation
values, and the corresponding timestamps. A maximum deviation value greater than 100% of the total limit
in any axis indicates a problem that must be resolved. Compare the corresponding timestamps with the
prepared test sequence to identify which action produced the problem. Contact Garmin for assistance in
resolving the problem.
NOTE
Common reasons for a failed magnetometer interference test are:
• new equipment is installed in close proximity to the GMU magnetometer or
• An existing or new electronic device has become grounded through the aircraft structure instead
of by proper ground wire in a twisted shielded pair, or
• Use of magnetized tools in close proximity to the GMU 11.
5.5 Engine Indication Troubleshooting
EIS indication failures may be presented as red x’s on the gauges as shown in Figure 5-9, or as operation
anomalies. Reference Table 5-8 below for troubleshooting guidance.
Figure 5-9 – Engine/Airframe Failure Indications
Table 5-8 – EIS Gauges Troubleshooting

Symptom or
Failure Message
Power removed Ensure GEA 24(B) circuit breaker is not open.
from GEA 24(B).
Inspect wiring and electrical connections.
Defective or
If problem persists, replace the GEA 24(B) with a known good
failed GEA
unit.
24(B).
Power Cycle power and permit time for initialization.
interrupted
during
Engine Indications
initialization.
Red X’d
Software and Reload software.
configuration
load error.
Temperature Inspect temperature probe(s) and wiring.
EGT/CHT only probe is shorted
(typically where the
Red X’d
bayonet is
crimped).
EGT temperature Electrical open in Inspect EGT probes and wiring.

slowly drift up and the probe or
eventually flag wiring.

Page 52
Symptom or
Failure Message
Resistor failure. Disconnect P-Lead signal wires at
both ends. Verify wire is more than 400 KΩ.
• Replace wire and parallel resistors if less than 400 KΩ
Unstable RPM
Poor connection. Verify wiring and connections.
Interference. Route signal wires away from spark plug leads and power wires.
Resistor failure. Disconnect P-Lead signal wires at
both ends. Verify wire is more than 400 KΩ.
Unstable RPM
during magneto • Replace wire and parallel resistors if less than 400 KΩ.
check
Starting vibrator None.
RPM is erratic is installed.
during engine Normal operation
start/cranking with p-lead RPM
input.
Fuel quantity Fuel probe Replace fuel probe.
gauge is malfunction.
inaccurate
Probe out of Recalibrate fuel tank probes
calibration.
Incorrect Comply with Garmin Service Bulletin 2134.
resistors installed
in harness
between GEA 24
and resistive fuel
probe.
Incorrect Verify correct configuration setting (reference section B.7 and
configuration G3X Installation Manual Rev. 14 or later).
setting for
resistive fuel
probe.
GEA 24 replaced Verify configuration settings (reference section B.7 and G3X
by GEA 24B. STC Installation Manual Rev. 14 or later) and recalibrate fuel
tank probes.
Fuel flow Calibrate fuel flow. (1)
Fuel totalizer
requires Replace fuel flow transducer
inaccurate
calibration
Fuel flow Poor connection. Verify wiring and connections

indication is Air/contamination Purge fuel lines of air, verify sensor orientation and clean the
unstable in the sensor. sensor.

Page 53
Symptom or
Failure Message
Interference. Route wires away from spark plug leads and power wires. Install
EMI shield.
• Replace fuel flow transducer if symptoms persist
Pressure line Verify manifold pressure line vent (if installed) is clear.
drain plugged.
Manifold pressure Verify fuel is not trapped in the manifold pressure line.
unstable
Sensor failure. Replace manifold pressure sensor
Pressure line Verify manifold pressure line is clear of obstructions.
Manifold pressure blocked.
inaccurate
Sensor failure. Replace pressure manifold sensor.
The GEA 24(B) Check GEA 24(B) configuration, calibration, and wiring. Verify
Engine Interface has a compliance with Garmin Service Bulletin 2134.
configuration error configuration
error.
Notes:
(1) Reference the G3X Touch EFIS Part 23 AML STC Installation Manual (190-02472-01)
5.6 Traffic Alert Messages

Table 5-9 – Traffic Alert Troubleshooting
• Interface to the G3X has Inspect unit wiring and connections for faults
failed
• Traffic device has failed Troubleshoot the device failure in accordance
with the LRU maintenance manual
5.7 Transponder Alert Messages

Table 5-10 – Transponder Alert Troubleshooting
GPS data connection from Verify ADS-B sourced GPS receiver has a
external navigator lost GPS signal
Verify external navigator has power and is
functioning properly
Transponder failure Verify the transponder is powered on and
“Red X’d” XPDR functional.
Communication lost Verify the GSU 25D is powered on and
between transponder and functional (the transponder communicates
GSU 25D to G3X via the GSU).
XPDR Fault Hardware fault Contact Garmin Product Support

Page 54
XPDR CONFIG ERROR Transponder configuration Check transponder configuration

fault
Flight ID is not defined  if “Set by Pilot” is configured, ensure
correctly. the flight ID is an alpha numeric with
NO ID eight or less characters.
 If the flight ID was entered via GTX tool,
correct it.
5.8 Loss of Navigation Information (External Navigators)

If VHF/GPS Navigation information is removed from the G3X Touch GDU and “GPS” (in magenta) and “VFR”
and “REV” (both in yellow) are displayed on the PFD HSI:
Table 5-11 – Loss of Navigation Information (External Navigators)
Communication with • Complete troubleshooting as directed and

external GPS lost. PFD applicable in Sections 5.1 (General
automatically reverted to Troubleshooting) and 5.2 (CAN bus
internal GPS troubleshooting).
• Inspect and verify the ARINC 429 wiring
between GPS navigator and GAD
29B/29D.
• Verify the G3X Touch and GPS navigator
configurations have not changed.
Reference APPENDIX B
• Verify navigator is functioning properly.
Reference the navigator manufacturer’s
troubleshooting procedures.
• If problem persists, replace the GAD 29B
or navigator as applicable with a known
good unit.
Contact Garmin Product Support before replacing
unit to determine all troubleshooting options have
been accomplished.
5.9 Garmin GFC 500 Failure Messages

During operation of the GFC 500 AFCS, the G3X Touch GDU may annunciate a failure or fault that is
specific to the GFC 500 Autopilot system. Refer to the GFC 500 Autopilot with Electronic Stability Protection
Part 23 AML STC Maintenance Manual with Instructions for Continued Airworthiness (190-02291-01), for
assistance in troubleshooting the problem.
5.10 Loss of Non-Garmin Autopilot Heading and/or Course Datum

If a Non-Garmin autopilot loses the capability to couple and track Heading and/or Course Datum:
1. Complete troubleshooting as directed and applicable in Sections 5.1, 5.2 (CAN bus troubleshooting),
5.4.2 (for loss of heading datum) and 5.10 (for loss of course and GPSS datum).
2. Inspect and verify the ARINC 429 wiring between GPS navigator, GAD 29B/29D and the autopilot
computer.

Page 55
3. Inspect the analog wiring between the GAD29B and the autopilot computer.
4. Verify the G3X Touch and GPS navigator configurations have not changed. Reference APPENDIX B
5. Verify autopilot computer is functioning properly. Reference the autopilot manufacturer’s
troubleshooting procedures.
6. If problem persists, replace the GAD 29B/29D with a known good unit.
5.11 Miscellaneous Alerts

Table 5-12 – Miscellaneous Alerts
Alert/Failure Message Possible Cause Recommended Action
Database error Verify databases are up to date

TAWS FAIL
Loss of GPS position Verify GPS signal is available
Power removed from GAD 27 Ensure GAD 27 circuit breaker is not open.
Defective or failed GAD 27 Inspect wiring and electrical connections.
ECS FAIL Electrical Control System tab If problem persists, replace the GAD 27
is configured as “Enabled” with a known good unit.
and the GAD 27 is powered
off or failed.
Power lost from the CO Inspection CO detector wiring and
detector electrical connections.
CO FAIL
Defective or failed CO Consult the CO detector manufacturer’s
detector. data for troubleshooting guidance.
Power removed from the Ensure COM or NAV circuit breaker is not
“Red X’d” COM or NAV COM or NAV radio open.
Defective wiring or failed Inspect wiring and electrical connections.
COM or NAV radio.
Power removed from the Ensure AUDIO circuit breaker is not open.
“Red X’d” Audio Panel
audio panel
Inspect wiring and electrical connections.
Defective wiring or failed
Audio panel.
GDU 470 display is in split  Select full screen format to view
screen mode and CAUTION messages
annunciations are not  Select on the lower section of
displayed. the display
GDU 470 display is in split
screen mode and WARNING
annunciations are not
displayed.
5.12 Aircraft Harness/LRU Connectors

This section describes the aircraft harness connectors and associated LRU connectors. The pin
arrangement for each LRU connector is shown and the LRU connector arrangement for units with more than
one connector will be shown in the following sections. LRU connector arrangements will show the aircraft
harness connector designations. Reference the G3X Touch EFIS Part 23 AML STC Installation Manual (190-
02472-01) for further detail.

Page 56
5.12.1 GDU 4X0 Aircraft Harness/LRU Connectors
This section describes the GDU 4X0 aircraft harness and interface connectors on the GDU. The GDU
connector designation is P4X01 and P4X02 and the aircraft harness connectors are designated as J4X01
and J4X02 respectively. GDU connector P4X03 is not used. The GDU connectors are clearly marked on the
back of the GDU as P4601, P4602 and P4603 for GDU 460 and P4701, P4702, and P4703 for GDU 470.
5.12.1.1 Aircraft Harness Connector J4X01

The aircraft harness connector J4X01 is a 9-socket D-sub plug connector and interfaces to the GDU P4X01
connector. A pinout arrangement of P4X01 is shown in Figure 5-10. Connector pin functions are shown in
Table 5-13.
Figure 5-10 – View of P4X01 Connector from back of GDU
Table 5-13 – P4X01/J4X01 Pin Functions

PIN PIN NAME I/O
1 RESERVED --
2 RESERVED --
3 RESERVED --
4 RS-232 TX OUT
5 RS-232 RX IN
6 RESERVED --
7 RESERVED --
8 RESERVED --
9 RS-232 GROUND --
5.12.1.2 Aircraft Harness Connector J4X02

The aircraft harness connector J4X02 is a 50-pin D-sub plug connector and interfaces to the GDU P4X02
connector. A pinout arrangement of P4X02 is shown in Figure 5-11 and connector pin functions are shown in
Table 5-14
Figure 5-11 – View of P4X02 Connector from back of GDU

Page 57
PIN PIN NAME I/O
1 ALERT AUDIO OUT HI OUT
2 RESERVED --
3 RESERVED --
4 RESERVED --
5 RESERVED --
6 RESERVED --
7 RESERVED --
8 RESERVED --
9 CDU SYSTEM ID PROGRAM 2 --
10 CDU SYSTEM ID PROGRAM 1 --
11 RESERVED --
12 RESERVED --
13 RS-232 TX 3 OUT
14 RS-232 RX 2 IN
15 RESERVED --
16 POWER GROUND 1 --
17 CONFIG MODULE POWER OUT OUT
18 ALERT AUDIO OUT LO OUT
19 RESERVED --
20 RESERVED --
21 RESERVED --
22 RESERVED --
23 RS-232 RX 4 IN
24 RS-232 RX 5 IN
25 RESERVED --
26 28V LIGHTING BUS HI IN
27 SYSTEM PROGRAM GROUND --
28 CAN BUS TERMINATION --
29 RS-232 RX 3 IN
30 RS-232 TX 2 OUT
31 AIRCRAFT POWER 2 --
33 CONFIG MODULE CLOCK I/O
34 RS-232 GROUND 1 --
35 RS-232 GROUND 2 --
36 RS-232 GROUND 3 --
37 RS-232 GROUND 4 --
38 RESERVED --
39 RESERVED --
40 RS-232 TX 4 OUT
41 RS-232 TX 5 OUT
42 RESERVED --
43 14V LIGHTING BUS HI IN
44 RS-232 GROUND 5 --
45 CAN-L I/O
46 CAN-H I/O
47 RS-232 RX 1 IN
48 RS-232 TX 1 OUT
49 CONFIG MODULE GROUND --
50 CONFIG MODULE DATA I/O

Page 58
5.12.2 GSU 25D Aircraft Harness/LRU Connectors
This section describes the GSU 25D aircraft harness and interface connectors on the GSU. The GSU
connector designation is J251 and J252 and the aircraft harness connectors are designated as P251 and
P252 respectively.
5.12.2.1 Aircraft Harness Connector P251

The aircraft harness connector P251 is a 9-socket D-sub plug connector and interfaces to the J251
connector on the GSU. A pinout arrangement of J251 is shown in Figure 5-12 and connector pin functions
are shown in Table 5-15.
Figure 5-12 – View of J251 Connector on the GSU 25D
Table 5-15 – P251/J251 Pin Functions

Pin Pin Name I/O
1 CAN-H I/O
2 CAN-L I/O
3 RESERVED --
4 RS-232 RX 1 IN
5 RS-232 TX 1 OUT
6 POWER GROUND --
7 AIRCRAFT POWER 1 IN
9 RS-232 GROUND --

connector on the GSU. A pinout arrangement of J251 is shown in Figure 5-13 and connector pin functions
Figure 5-13 – View of J252 Connector on the GSU 25D

Page 59
PIN PIN NAME I/O
1 TEMP PROBE POWER OUT OUT
2 TEMP PROBE IN HI IN
3 TEMP PROBE IN LO IN
4 RESERVED --
5 RESERVED --
6 RESERVED --
7 RESERVED --
8 RESERVED --
9 RS-232 TX 3 OUT
10 RS-232 RX 3 IN
11 RS-232 GROUND 3 --
12 RESERVED --
13 RESERVED --
14 RS-232 GROUND 2 --
15 RS-232 TX 2 OUT
5.12.3 GMU 11 Aircraft Harness/LRU Connector

This section describes the GMU 11 aircraft harness and interface connector. The GMU LRU connector
designation is J111 and he aircraft harness connector is designated as P111.
connector on the GMU. A pinout arrangement of J111 is shown in Figure 5-14 and connector pin functions
Figure 5-14 – View of J111 Connector on the GMU 11

Pin Pin Name I/O
1 CAN-H I/O
2 CAN-L I/O
3 RESERVED --
4 RESERVED --
5 RESERVED --
6 RESERVED --
9 POWER GROUND --

Page 60
5.12.4 GTP 59 Harness
The GTP59 is an OAT sensing device. The connection to this LRU is made via pre-installed lead wires and it
is acceptable to use crimp splices to extend the lead wire harness to the GSU. The pre-installed lead wires
are ten feet in length. Reference Table 5-18 for lead wire functions. For specific wiring information refer to
G3X Touch EFIS Part 23 AML STC Installation Manual (190-02472-01).
Table 5-18 – GTP 59 Lead Wire Functions
PIN WIRE I/O
WHITE TEMP PROBE POWER IN IN
BLUE TEMP PROBE OUT HI OUT
ORANGE TEMP PROBE OUT LO OUT
5.12.5 GAD 27 Aircraft Harness/LRU Connectors

This section describes the GAD 27 aircraft harness and the interface connectors on the GAD 27. The GAD
27 connector designation is J271 and the aircraft harness connector is designated as P271. GAD 27
connector J272 is not used. GAD 27 also has a terminal block TB273.

The aircraft harness connector P271 is a 50-socket D-sub plug connector and interfaces to the GAD 27
connector J271. A pinout arrangement of J271 is shown in Figure 5-15 and connector pin functions are
shown in Table 5-19.
Figure 5-15 – View of J271 Connector on the GAD 27

PIN PIN NAME/FUNCTION I/O
1 CAN HI I/O
2 CAN LO I/O
3 CAN BUS TERM --
4 GAD 27 POWER GND --
5 RESERVED --
6 RESERVED --
7 GAD 27 POWER IN
8 GAD 27 POWER GROUND --
9 RESERVED --
10 RESERVED --
11 RESERVED --
12 RESERVED --

Page 61
PIN PIN NAME/FUNCTION I/O
13 RESERVED --
14 RESERVED --
15 RESERVED --
16 RESERVED --
17 RESERVED --
18 RESERVED --
19 RESERVED --
20 RESERVED --
21 RESERVED --
22 RESERVED --
23 RESERVED --
24 RESERVED --
25 RESERVED --
26 RESERVED --
27 RESERVED --
28 RESERVED --
29 RESERVED --
30 RESERVED --
31 RESERVED --
32 RESERVED --
33 RESERVED --
34 LIGHT 1 SWITCH IN
35 LIGHT 2 SWITCH IN
36 ALTERNATING FLASH ON IN
37 RESERVED --
38 GAD 27 POWER GROUND --
39 RESERVED --
40 RESERVED --
41 RESERVED --
42 RESERVED --
43 RESERVED --
44 RESERVED --
45 RESERVED --
46 RESERVED --
47 RESERVED --
48 RESERVED --
49 RESERVED --
50 RESERVED --
5.12.5.2 Terminal Block TB273

This connection is only required for 14 VDC aircraft using p/n 235-00094-00 ring terminal. A terminal
arrangement of TB273 is shown in Figure 5-16 and connector terminal functions are shown in Table 5-20

Page 62
Figure 5-16 – View of TB273 Terminal Block on GAD 27
Table 5-20 – TB273 Terminal Functions

TERMINAL TERMINAL NAME/FUNCTION I/O
1 KEEP ALIVE POWER IN IN
2 KEEP ALIVE POWER V OUT OUT
3 LIGHT 1 POWER IN IN
4 LIGHT 2 POWER IN IN
5 RESERVED --
6 RESERVED --
7 RESERVED --
8 RESERVED --
9 LIGHT 1 POWER OUT OUT
10 LIGHT 2 POWER OUT OUT
5.12.6 GEA 24(B) Aircraft Harness/LRU Connectors

This section describes the GEA 24(B) aircraft harness and LRU interface connectors. The GEA connector
designations are J241, J242, J243 and J244 and the aircraft harness connectors are designated as P241,
P242, P243 and P244 respectively.
5.12.6.1 Aircraft Harness Connectors P241

connector on the GEA. A pinout arrangement of J241 is shown in Figure 5-17 and connector pin functions
Figure 5-17 – View of J241 Connector on the GEA 24(B)

PIN PIN NAME I/O
1 CAN HI I/O
2 CAN LO I/O
3 RESERVED --

Page 63
PIN PIN NAME I/O
4 RS-232 RX 1 IN
5 RS-232 TX 1 OUT
6 POWER GROUND --
9 RS-232 GROUND --
5.12.6.2 Aircraft Harness Connectors P242

The aircraft harness connector P242 is a 25-pin D-sub plug connector and interfaces to the J242 connector
on the GEA. A pinout arrangement of J242 is shown in Figure 5-18 and connector pin functions are shown in
Table 5-22

PIN PIN NAME I/O
1 RESERVED --
2 CHT CYL 6 LO IN
3 EGT CYL 6 LO IN
4 CHT CYL 5 LO IN
5 EGT CYL 5 LO IN
6 CHT CYL 4 LO IN
7 EGT CYL 4 LO IN
8 CHT CYL 3 LO IN
9 EGT CYL 3 LO IN
10 CHT CYL 2 LO IN
11 EGT CYL 2 LO IN
12 CHT CYL 1 LO IN
13 EGT CYL 1 LO IN
14 CHT CYL 6 HI OUT
15 EGT CYL 6 HI OUT
16 CHT CYL 5 HI OUT
17 EGT CYL 5 HI OUT
18 CHT CYL 4 HI OUT
19 EGT CYL 4 HI OUT
20 CHT CYL 3 HI OUT
21 EGT CYL 3 HI OUT
22 CHT CYL 2 HI OUT
23 EGT CYL 2 HI OUT
24 CHT CYL 1 HI OUT
25 EGT CYL 1 HI OUT

Page 64
Figure 5-19 – View of J243Connector on the GEA 24(B)

PIN PIN NAME I/O
1 FUEL PRESS GND --
2 FUEL PRESS RX IN
3 FUEL PRESS XDCR +12V OUT
4 FUEL PRESS XDCR +5V OUT
5 RPM 2 GND --
6 RPM 2 IN
7 RPM 1 GND --
8 RPM 1 IN
9 RPM 1 +12V OUT
10 RPM 2 +12V OUT
11 RESERVED --
12 MANIFOLD PRESS GND --
13 MANIFOLD PRESS RX IN
14 MANIFOLD PRESS XDCR +12V OUT
15 MANIFOLD PRESS XDCR +5V OUT
16 OIL PRESS GND --
17 OIL PRESS RX IN
18 OIL PRESS XDCR +12V OUT
19 OIL PRESS XDCR +5V OUT
20 FUEL FLOW 1 GND --
21 FUEL FLOW 2 RX IN
22 FUEL FLOW 2 GND --
23 FUEL FLOW 1 RX IN
24 FUEL FLOW 1 XDCR +12V OUT
25 FUEL FLOW 2 XDCR +12V OUT
26 RESERVED --
27 RESERVED --
28 TIT 2 LO IN
29 TIT 2 HI IN
30 TIT 1 LO or CARBURETOR TEMP LO IN
31 TIT 1 HI or CARBURETOR TEMP HI IN
32 OIL TEMP LO IN
33 OIL TEMP HI IN
34 BUS 2 AMPS LO IN
35 BUS 2 AMPS HI IN
36 BUS 1 AMPS LO IN
37 BUS 1 AMPS HI IN

Page 65
are shown in Table 5-24

PIN PIN NAME I/O
1 RESERVED --
2 RESERVED --
3 RESERVED --
4 RESERVED --
5 RESERVED --
6 FUEL QTY 1 IN
7 RESERVED --
8 RESERVED --
9 FUEL QTY 2 IN
10 RESERVED --
11 RESERVED --
12 FUEL QTY 3 IN
13 RESERVED --
14 RESERVED --
15 FUEL QTY 4 IN
16 RESERVED --
17 RESERVED --
18 RESERVED --
19 RESERVED --
20 RESERVED --
21 RESERVED --
22 RESERVED --
23 RESERVED --
24 RESERVED --
25 VOLTS 1 IN
26 RESERVED --
27 RESERVED --
28 VOLTS 2 IN
29 RESERVED --
30 RESERVED --
31 RESERVED --

Page 66
PIN PIN NAME I/O
32 RESERVED --
33 RESERVED --
34 FUEL QUANTITY 1 XDCR +12V OUT
35 FUEL QUANTITY 2 XDCR +12V OUT
36 RESERVED --
37 RESERVED --
38 RESERVED --
39 RESERVED --
40 RESERVED --
41 RESERVED --
42 RESERVED --
43 RESERVED --
44 MASTER WARNING IN
45 MASTER CAUTION IN
46 RESERVED --
47 RESERVED --
48 RESERVED --
49 RESERVED --
50 FUEL QUANTITY 3 & 4 XDCR +12V OUT
5.12.7 GAD 29B/29D Aircraft Harness/LRU Connectors

This section describes the GAD 29B/29D aircraft harness and LRU interface connectors. The GAD 29
connector designations are J291 and J292 and the aircraft harness connectors are designated as P291 and
P292 respectively.

connector on the GAD29B. A pinout arrangement of J291 is shown in Figure 5-21 and connector pin
functions are shown in Table 5-25.
Figure 5-21 – View of J291 Connector on the GAD 29B/29D

PIN PIN NAME I/O
1 CAN-H I/O
2 CAN-L I/O
3 RESERVED --
4 RESERVED --
5 RESERVED --
6 POWER GROUND --
9 GROUND --

Page 67
The aircraft harness connector P292 is a 25-pin D-sub plug connector and interfaces to the J291 connector
on the GAD29B. A pinout arrangement of J292 is shown in Figure 5-22 and connector pin functions are
shown in Table 5-26.
Figure 5-22 – View of J292 Connector on the GAD 29B/29D

PIN PIN NAME I/O
1 AC REFERENCE HI IN
2 AC REFERENCE LO IN
3 HDG/CRS VALID OUT
4 ARINC 429 RX 4B IN
6 ARINC 429 TX 2B OUT
8 HEADING ERROR HI OUT
9 CAN TERM 1 --
14 HEADING ERROR LO IN
15 COURSE ERROR HI OUT
16 ARINC 429 RX 4A IN
18 ARINC 429 TX 2A OUT
20 COURSE ERROR LO IN
21 CAN TERM 2 --
5.12.8 GDL 5XR Aircraft Harness/LRU Connectors

This section describes the GDL 5XR aircraft harness and interface connector. The GDL LRU connector
designation is J5X1 and the aircraft harness connector is designated as P5X1.
The aircraft harness connector P5X1 is a 15-socket D-sub plug connector and interfaces to the J5X1
connector on the GMU. A pinout arrangement of J5X1 is shown in Figure 5-23 and connector pin functions

Page 68
Figure 5-23 – View of J5X1 Connector on the GDL 5XR

PIN PIN NAME I/O
1 RESERVED --
2 RESERVED --
3 RESERVED --
4 RESERVED --
5 RS-232 TX 2 OUT
6 RS-232 RX 2 IN
7 RS-232 TX 1 OUT
8 RS-232 RX 1 IN
9 POWER GROUND --
10 AIRCRAFT POWER IN
11 RS-232 GROUND 1 --
12 RS-232 GROUND 2 --
13 MUSIC OUT LEFT OUT
14 AUDIO COMMON --
15 MUSIC OUT RIGHT OUT
5.12.9 GTR 20/200B Aircraft Harness/LRU Connector

This section describes the GTR 20 or GTR 200B aircraft harness and LRU interface connectors. The GTR
connector designation is J2001 and the aircraft harness connector is designated as P2001.
The aircraft harness connector P2001 is a 37 socket D-sub plug connector and interfaces to the J2001
connector on the GTR 20 or GTR 200B. A pinout arrangement of J2001 is shown in Figure 5-24 and
connector pin functions are shown in Table 5-28.
Figure 5-24 – View of J2001 Connector on GTR 20 or GTR 200B

PIN PIN NAME I/O
1 AIRCRAFT POWER IN
2 RESERVED --
3 LIGHTING BUS IN

Page 69
PIN PIN NAME I/O
4 TRANSMIT INTERLOCK OUT* OUT
5 TRANSMIT INTERLOCK IN* IN
6 CAN-L I/O
7 CAN-H I/O
8 ID IN --
9 AUX 2 AUDIO IN HI IN
10 SUMMED AUDIO OUT HI OUT
11 COPILOT HEADSET RIGHT OUT
12 COPILOT HEADSET LEFT OUT
13 PILOT HEADSET RIGHT OUT
14 PILOT HEADSET LEFT OUT
15 COPILOT PTT IN* --
16 COPILOT MIC AUDIO IN HI IN
17 PILOT MIC AUDIO IN HI OUT
18 MUSIC 1 IN RIGHT IN
19 MUSIC 1 IN LEFT IN
20 AIRCRAFT GROUND --
21 RESERVED --
22 RESERVED --
23 RESERVED --
24 RESERVED --
25 CAN TERM 2 --
26 CAN TERM 1 --
27 ID LO --
28 AUX 2 AUDIO IN LO --
29 SUMMED AUDIO OUT LO OUT
30 COPILOT HEADSET LO --
31 AUX 1 AUDIO IN LO IN
33 PILOT HEADSET LO --
34 COPILOT MIC AUDIO IN LO IN
35 PILOT PTT IN* IN
36 PILOT MIC AUDIO IN LO IN
37 MUSIC IN LO --
5.12.10 GMA 245R Aircraft Harness/LRU Connectors

This section describes the GMA 245R with Marker Beacon aircraft harness and LRU interface connectors.
The GMA connector designations are J2401 and J2402 and the aircraft harness connectors are designated
as P2401 and P2402 respectively.

The aircraft harness connector P2401 is a 44-pin D-sub plug connector and interfaces to the J2401
connector on the GMA 245R. A pinout arrangement of J2401 is shown in Figure 5-25 and connector pin
Figure 5-25 – View of J2401 Connector on GMA 245R

Page 70
PIN PIN NAME I/O
1 MARKER ANTENNA HI IN
2 MARKER ANTENNA LO IN
3 TEL AUDIO IN HI IN
4 TEL AUDIO LO --
5 TEL MIC AUDIO OUT HI OUT
6 RESERVED --
8 AUX 2 AUDIO IN LO --
9 COM 1 AUDIO IN HI IN
10 COM 1 AUDIO LO --
11 COM 1 MIC AUDIO OUT HI OUT
12 COM 1 MIC KEY OUT OUT
13 COM 2 AUDIO IN HI IN
14 COM 2 AUDIO LO --
15 COM 2 MIC AUDIO OUT HI OUT
16 PILOT ICS KEY IN* IN
17 NAV 1 AUDIO IN HI IN
18 NAV 1 AUDIO IN LO IN
19 NAV 2 AUDIO IN HI IN
20 NAV 2 AUDIO IN LO IN
22 AUX 1 AUDIO IN LO IN
24 COM ACTIVE OUT* OUT
25 RESERVED --
26 RESERVED --
27 RESERVED --
28 RESERVED --
29 ALERT 3 AUDIO IN HI IN
30 COM 2 MIC KEY OUT* OUT
32 ALERT 1 AUDIO IN LO IN
33 PILOT MIC AUDIO IN HI IN
34 PILOT MIC KEY IN* IN
35 PILOT MIC AUDIO IN LO IN
36 CAN-H I/O
37 CAN-L I/O
38 RESERVED --
39 RESERVED --
40 PASS HEADSET LEFT OUT
41 PASS HEADSET RIGHT OUT
42 PASS HEADSET LO --
43 AUX 3, ALERT 3, 4 AUDIO LO --

The aircraft harness connector P2401 is a 44-pin D-sub plug connector and interfaces to the J2402
connector on the GMA 245R. A pinout arrangement of J2402 is shown in Figure 5-26 and connector pin

Page 71
Figure 5-26 – View of J2402 Connector on GMA 245R

PIN PIN NAME I/O
1 PILOT HEADSET LO --
2 COPILOT HEADSET LO --
3 COPILOT HEADSET LEFT OUT
4 COPILOT HEADSET RIGHT OUT
5 RESERVED --
6 RESERVED --
7 RESERVED --
9 RESERVED --
10 POWER GROUND --
11 RESERVED --
12 RESERVED --
13 PASSENGER ICS KEY IN* IN
14 ALERT 2, FAILSAFE AUDIO LO --
16 PILOT HEADSET LEFT OUT
17 RESERVED --
18 RESERVED --
19 RESERVED --
20 COM SWAP IN* IN
21 RESERVED --
22 PLAY KEY IN* IN
25 MUSIC 1 IN LO --
28 MUSIC 2 IN LO --
29 FAILSAFE WARN AUDIO IN HI IN
30 COPILOT ICS KEY IN* IN
31 PILOT HEADSET RIGHT OUT
32 COPILOT MIC AUDIO IN HI IN
33 COPLIOT MIC KEY IN* IN
34 COPILOT MIC AUDIO IN LO IN
35 PASS 1 MIC AUDIO IN HI IN
36 PASS 1 MIC AUDIO IN LO IN
43 CABIN SPEAKER OUT HI OUT

Page 72
PIN PIN NAME I/O
44 CABIN SPEAKER OUT LO --
5.12.10.3 GMA 245R Dip Switch Configuration Settings

Table 5-31 – GMA 245R DIP Switch Configuration Settings
Switch Function Description
1 ENABLED KEYED When set to ON, the intercom system (ICS) will only allow intercom
ICS MIC audio to be heard when the corresponding ICS KEY for the MIC
position is pressed. When set to ON, auto squelch will NOT be
active.
2 PILOT IN RIGHT This setting is for intercom 3D audio. Normally the Pilot will be
SEAT positioned to the left in the Copilot’s headset, and the Copilot will be
positioned to the right in the Pilot’s headset. When set to ON, this
setting reverses that so the Pilot is positioned to the right in the
Copilot’s headset, and the Copilot is positioned to the left in the
Pilot’s headset.
3 MUTE ON COM TX When set to ON, the monitored COM radio is muted during mic-
selected COM transmission (mic-selected COM is still heard, but not
the monitored COM radio).
4 RESERVED LEAVE SWITCH IN OFF POSITION
8 CONFIGURATION LEAVE SWITCH IN OFF POSITION
LOCKOUT
5.12.11 GAP 26 Harness

The GAP 26 is an Angle of Attack (AOA) probe. The connection to this LRU is made via pre-installed lead
wires to an AOA switch and aircraft ground.

Page 73
6. G3X EQUIPMENT REMOVAL & REINSTALLATION
This section contains basic procedures for removing and reinstalling G3X LRUs.
The G3X Touch EFIS equipment part numbers approved by STC SA01899WI are in the G3X Touch EFIS
Part 23 AML STC Installation Manual (190-02472-01).
NOTE
Once an LRU is replaced, software loading, and testing is required. See Section 7 for the software
loading and testing procedures for a replacement LRU.
CAUTION
Always ensure aircraft power is off or LRU circuit breaker is open when removing and/or replacing an
LRU. Unplug any auxiliary power supplies
NOTE
Ensure all LRU mounting hardware removed is retained for reinstallation. If hardware needs to be
replaced, reference G3X Touch EFIS Part 23 AML STC Installation Manual (190-02472-01) appropriate
hardware part numbers.
6.1 GDU 4X0

Removal:
1. Power OFF the aircraft to remove power from the GDU and other LRUs.
2. Using a 3/32” hex tool, rotate all four fasteners counter-clockwise to remove them.
3. Carefully remove the display from the panel.
4. While supporting the display, disconnect all connectors and the GSU 25D without disconnecting the
pitot/static/AOA lines (if installed on back of GDU, as defined in Section 6.2).
Reinstallation:
1. Inspect the connector and pins (on the unit) for signs of damage.
2. While supporting the display, connect the connectors to the rear of the unit and GSU 25D if installed
on the back of GDU (as defined in Section 6.2).
3. Carefully insert the display into the panel cutout and align fasteners with the corresponding holes.
Do not use excessive force while inserting the display.
4. Using a 3/32” hex tool, insert screws and rotate clockwise to tighten and torque to 8 ±1 in-lbs. to
secure display to the instrument panel.
5. Continue to section 7.1 for configuration and checkout procedures.

Page 74
115-01725-01 NUTPLATE
AND
8X MS20426AD3-X RIVETS
OR
4X MS21071-06 NUTPLATES
AND
8X MS20426AD3-X RIVETS
4X 211-00169-01 INSTRUMENT
OR PANEL
4X MS16995-18-B
SCREWS
TORQUE TO
8±1 IN-LB
Figure 6-1 – GDU 460 Shown, (GDU 470 Similar)
6.1.1 PFD Configuration Module

The GDU 4X0 PFD display uses a configuration module designated as the master system configuration
module. The master system configuration module stores configuration data identical to the PFD configuration
data stored in the PFD memory. The PFD cross-checks the configuration module data against internal PFD
memory and self-configures to match the master system configuration module. The PFD also maintains
control of other LRUs’ configuration and calibration settings such as the GSU 25D. This allows critical data to
be retained with the airframe even if the PFD display is replaced.
NOTE
All item numbers (in parenthesis) in this procedure reference Figure 6-2.
Removal:
1. Remove the PFD in accordance with Section 6.1 to gain access to connector J4X02.
2. Remove the backshell cover (8) from connector J4X02 by removing the two screws (7).
3. Remove the screw (4) securing the configuration module (1) to the backshell (6).
4. Lift the configuration module (1) out of the backshell (6) and disconnect the wiring harness (3) from
the module.
5. Inspect the wiring harness (3) and connector pins (2) for damage, loose wiring, or corrosion. Repair
any defects or replace components as necessary.

Page 75
Reinstallation:
1. Inspect the connectors to ensure there are no bent or damaged pins. Repair any damage.
2. Connect the wiring harness (3) to the new configuration module (1).
3. Install the new configuration module in the connector backshell (6) and secure with screw (4)
4. Reinstall the backshell cover (8) using the two screws (7).
5. Reconnect the J4X02 connector on the back of the GDU.
6. Reinstall the PFD in accordance with Section 6.1.
4
1
Figure 6-2 – Configuration Module (PFD)
Table 6-1 – GDU Configuration Module Kit (P/N 010-12253-01)

Item Description Qty. Required Part Number
1 Potted Module (w/EEPROM) 1 011-03702-00
2 Contact, Socket, Size 20, 26-30 AWG 4 336-00022-01
3 4 conductor Config. Module harness 1 325-00122-00
4 Pan head screw 1 211-60232-07
NOTE
System configuration will be automatically copied to the module by the PFD upon the first power ON after
replacement. If the PFD was also replaced in conjunction with the module, system configuration and
calibration will be required.

Page 76
6.2 GSU 25D ADAHRS
Removal:
GDU-mounted GSU 25D:
1. Remove the GDU in accordance with Section 6.1.
2. Disconnect the GSU 25D electrical connectors.
3. Disconnect the pitot, static, and AOA lines as required and install plugs or covers to protect the
system.
4. While supporting the GSU 25D, remove the four bolts that attach the GSU 25D to the back of the
GDU.
4X 212-00035-10
OR
NAS1149F0363P
WASHERS
4X 212-00081-03
OR
MS35333-39 WASHERS
4X 211-00090-05 GSU 25D

OR
AN3-7A
BOLTS
GDU 460
Figure 6-3 – GDU 460-Mounted GSU 25D (GDU 470 similar)

Remote mounted GSU 25D:
1. Gain access to the GSU 25D. Refer to the location information recorded in APPENDIX A of this
document and maintained with the aircraft records.
2. Disconnect the GSU 25D electrical connectors.
3. Disconnect the pitot, static, and AOA lines as required and install plugs or covers to protect the
system.
4. Unscrew the four bolts or screws that secure the GSU 25D to the mounting location. Note the
mounting orientation for reinstallation.
5. Lift the GSU 25D off the mounting location.

Page 77
4X #10 BOLTS OR SCREWS
4X WASHERS
GSU 25D
EXISTING OR
FABRICATED
SHELF
4X #10 WASHERS
&
4X #10 NUTS
OR
4X #10 MIL-SPEC
NUTPLATES
Figure 6-4 – Remote mounted GSU 25D
Reinstallation:
GDU-mounted GSU 25D:
1. Place the GSU 25D on the back of the GDU in the same mounting orientation as it was when
removed. Align GSU holes with the mounting holes on the back of the GDU.
2. Insert the four mounting bolts and secure the GSU 25D on the back of the GDU.
3. Connect the pitot, static, and AOA lines.
4. Inspect the electrical connector to ensure there are no bent or damaged pins. Repair any damage.
5. Connect the electrical connectors to the GSU 25D.
6. Reinstall the GDU as noted in Section 6.1.
Remote mounted GSU 25D:
1. Place the GSU 25D on the mounting location in the same mounting orientation as it was when
removed. Align GSU holes with the holes on the mounting location. Connect the electrical connectors
to the GSU 25D.
2. Insert the four mounting bolts or screws and secure the GSU 25D to the mounting location with
washers and nuts (as applicable).
3. Connect the pitot, static, and AOA lines.
5. Connect the electrical connectors to the GSU 25D.

Page 78
6.3 GMU 11 Magnetometer
Removal:
1. Gain access to the GMU 11. Refer to the location information recorded in APPENDIX A of this
2. Disconnect the electrical connector.
3. Remove the 4 fasteners that secure the GMU 11 to the mounting location.
4. Lift the GMU 11 off the mounting location.
Reinstallation:
1. Place the GMU 11 in its mounting location and align its holes with the mounting holes.
2. Insert the four mounting screws and secure the GMU 11 in place with washers and nuts. Tighten
screws until snug, plus 1/4 turn.
4. Connect the electrical connector to the GMU 11.
5. Continue to section 7.2 for configuration/calibration and checkout procedures.
GMU 11
Down 4X #6 SCREWS
Existing or
Fabricated Shelf
4X #6 WASHERS
and
4X #6 NUTS
OR
4X #6 MIL-SPEC
NUTPLATES
Figure 6-5 – GMU 11 Magnetometer
6.4 GTP 59 Temperature Probe

Removal:
1. Ensure power is removed from the GSU 25D.
2. Remove the mounting nut and washer from the GTP 59 probe.
3. Pull the GTP 59 from the mounting hole.
Reinstallation:
1. Place the GTP 59 on the previous installation location.
2. Install the washer and nut.
3. Torque nut to 100 +/- 20 in-lbs.
4. Continue to section 7.4 for checkout procedures.

Page 79
NOTE
Reference the G3X Touch EFIS Part 23 AML STC Installation Manual (190-02472-01) for installation of
new GTP 59.
Figure 6-6 – GTP 59 Temperature Probe
6.5 GAD 27 Electronic Adapter Unit

Removal:
1. Gain access to the GAD 27. Refer to the location information recorded in APPENDIX A of this
2. Disconnect the GAD 27 connector and ring terminals from the terminal block. Note the location of
each ring terminal on the terminal block for proper reinstallation.
3. Remove the four screws and washers and nuts (as applicable) that secure the GAD 27 to the
mounting location.
4. Lift the GAD 27 off the mounting location.
Reinstallation:
1. Place the GAD 27 in its mounting location and align its holes with the mounting holes.
2. Insert the four mounting screws and secure the GAD 27 in place with washers and nuts or on

Page 80
nutplates as applicable.
4. For a newly installed GAD 27, install the d-sub cover plate on unused connector.
5. Connect the connector and ring terminals to the GAD 27.
6. Continue to section 7.5 for configuration and checkout procedures
2X 211-60234-05
SCREWS
4X #8 SCREWS
4X #8 WASHERS
115-03134-00
COVER
GAD 27
EXISTING OR
FABRICATED
SHELF
4X #8 WASHERS
&
4X #8 NUTS
OR
4X #8 MIL-SPEC
NUTPLATES
Figure 6-7 – GAD 27
6.6 GEA 24(B) Engine Indicating System

Removal:
1. Gain access to the GEA 24(B). Refer to the location information recorded in APPENDIX A of this
2. Disconnect the GEA 24(B) electrical connectors.
3. Remove the four screws that hold the GEA to the mounting location.
4. Lift the GEA 24(B) off its mounting location.
Reinstallation:
1. Place the GEA 24(B) in its mounting location and align its holes with the mounting holes.
2. Insert the four mounting screws and secure the GEA 24(B) in place.
3. Inspect the electrical connectors and pins for signs of damage. Repair any damage.
4. Connect the wiring harness connectors to the GEA 24(B).

Page 81
4X #10 SCREWS
4X #10 WASHERS
GEA 24 (B)
EXISTING OR
FABRICATED
SHELF
4X #10 WASHERS
&
4X #10 NUTS
OR
4X #10 MIL-SPEC
NUTPLATES
Figure 6-8 – GEA 24(B)
6.6.1 EIS Sensors

In addition to the data in this manual and the G3X Touch EFIS Part 23 AML STC Installation Manual (190-
02472-01), replacement or re-installation of each probe/sensor and wire must be accomplished in
accordance with the sensor manufacturer instructions or as recommended by the engine manufacturer. Wire
routing and clamping must follow procedures defined in the aircraft maintenance manual, standard practices
manual, or practices defined in Chapter 11, Electrical Systems, of advisory circular AC 43.13-1B, Aircraft
Inspection and Repair.
Sensors must be connected using hoses and fittings approved as part of aircraft or engine type certificated
design or standard aircraft parts (AN/MS) or the G3X Touch EFIS Part 23 AML STC Installation Manual
(190-02472-01).
After removing or replacing any EIS sensor, perform the EIS ground checkout procedure for the specific
sensor that was affected in Section 8.12
6.6.1.1 Pressure Sensors (Oil, Manifold and Fuel)

Manifold pressure, oil pressure, and fuel pressure sensor installations are similar.
When replacing existing sensors:
• Do not remove engine and fuel fittings with an intentionally reduced orifice. It may limit fluid loss and
fire damage in the event of a hose failure.
• Do not remove previously installed devices designed to absorb pressure shock/surge such as a
snubber.
• Reuse manifold tubing if it has a vent hole and install the manifold pressure sensor so it is not at the
low point in the line.
• Inspect the condition of all existing tubes, hoses, and fittings that are being reused; replace if
necessary.
Page 82
• Verify that the supply voltage and sensor configuration are correct if a different sensor is installed
(e.g. if a brass sensor is replaced by a GPT sensor). Refer to Table B-7 for configuration settings.
Install pressure sensors as described in Figure 6-9 or Figure 6-10. When installing pressure sensors:
1. New fuel and oil hoses in the engine compartment must meet TSO-C53a Type C or D (fire
resistant). Only use approved aircraft fittings (e.g. AN/AS-spec or Mil-spec) and hoses (e.g.
Aeroquip 303 or Aeroquip AE 466). All hoses must be rated for the pressure, temperature, and be
compatible with the fuel or oil.
2. Do not install sensors directly below fittings or components that may leak flammable fluid.
3. Thread sealant must be used for the NPT threads. To reduce the risk of system contamination, a
minimal amount of sealant should be applied leaving at least two threads at the end of the fitting
clear of sealant.
4. Sensor hoses must be routed as far away from the aircraft exhaust system as practical and no
closer than 6 inches.
5. Line fittings, routing, alignment, bonding, and support spacing must be installed as defined in the
aircraft maintenance manual or section 8-31 of AC 43.13-1B, Aircraft Inspection and Repair.

Page 83
1 2
1 12 TUBE, Ø0.190 IN OD
1 11 NAS1149F0332P WASHER, FLAT, STEEL, CAD PLATED, 0.032 INCH THICK, ID 0.203, OD 0.438
1 10 MS51958-65 SCREW, MACHINE, PAN HEAD, CROSS RECESSED 0.190-32UNF-2A, 3/4 INCH LONG
1 9 MS51533B3 SLEEVE, COMPRESSION, TUBE FITTING, 37° FLARED, Ø3/16 TUBE OD

1 8 MS21919WDG9 CLAMP, LOOP TYPE, CUSHIONED, Ø9/16 TUBE
1 7 MS21042L3 NUT, SELF-LOCKING, REDUCED HEXAGON, REDUCED HEIGHT, RING BASE 0.1900-32UNF-3B
1 6 AN910-1W COUPLING, PIPE, 1/8-27 ANPT

1 5 AN818-3 NUT, TUBE COUPLING, SHORT, Ø0.1875 TUBE OD 0.3750-24UNJF-3B
AN816-3 ADAPTER, STRAIGHT, PIPE TO TUBE, 1/8-27 NPT TO 0.3750-24 UNJF-3A
1 4 AN822-3 ADAPTER, ELBOW 90 DEG, PIPE TO TUBE, 1/8-27 NPT TO 0.3750-24 UNJF-3A
AN823-3 ADAPTER, ELBOW 45 DEG, PIPE TO TUBE, 1/8-27 NPT TO 0.3750-24 UNJF-3A
1 1 011-04202-XX PRESSURE SENSOR
QTY ITEM PART NUMBER DESCRIPTION
NOTE
1 TO PREVENT FLUID ENTRAPMENT, ORIENT THE SENSOR SO IT IS NOT STRAIGHT UP.
2 PRESSURE SENSOR HAS 1/8-27 NPT PIPE THREAD. SEE ADDITIONAL LOCATION AND INSTALLATION INFORMATION IN THIS SECTION.
3 EITHER ALUMINUM OR STEEL ADAPTERS ARE ACCEPTABLE. REFER TO APPLICABLE STANDARD FOR MATERIAL OPTIONS.
4 IF HOSE OR TUBING IS PREVIOUSLY INSTALLED, USE APPROVED AIRCRAFT FITTING (E.G. AN/AS-SPECIFICATION OR MIL-SPEC) TO CONNECT THE
SENSOR
Figure 6-9 – Brass Pressure Sensor (Coupling Mount Example)

Page 84
1 2
ALTERNATIVE
CLAMPING
OPTION
1 11 MS21919WDG14 CLAMP LOOP TYPE, CUSHIONED, SUPPORT, Ø7/8 TUBE
1 10 AN818-3 NUT, TUBE COUPLING, SHORT, Ø0.188 TUBE OD, 0.3750-24 UNJF-3B
1 9 MS51533B3 SLEEVE, COMPRESSION, TUBE FITTING, 37° FLARED, Ø3/16 TUBE OD

1 8 TUBE, Ø0.190 IN OD
AN816-3 ADAPTER, STRAIGHT, PIPE TO TUBE 1/8-27 NPT TO 0.3750-24 UNJF-3A
1 7 AN822-3 ELBOW. PIPE TO TUBE, 90°, 1/8-27 NPT TO 0.3750-24 UNJF-3A
AN823-3 ELBOW, PIPE TO TUBE, 45°, 1/8-27 NPT TO 0.3750-24 UNJF-3A
1 6 AN910-1W COUPLING. PIPE, 1/8-27 ANPT
NUT, SELF-LOCKING, 450°F, REDUCED HEXAGON, REDUCED HEIGHT, RING BASE,
1 5 MS21042L3
NON-CORROSION RESISTANT STEEL, 0.190-32 UNF-3B
1 4 NAS1149F0332P WASHER, FLAT, STEEL, CAD PLATED, 0.032 INCH THICK, ID 0.203, OD 0.438
SCREW, MACHINE PAN-HEAD, CROSS-RECESSED, CORROSION RESISTING STEEL, 0.190-32

1 3 MS51958-X
UNF-2A
1 2 MS21919WDG9 CLAMP LOOP TYPE, CUSHIONED, SUPPORT, Ø9/16 TUBE
1 1 011-05783-XX PRESSURE SENSOR, GPT
QTY ITEM PART NUMBER DESCRIPTION
NOTES
1 TO PREVENT FLUID ENTRAPMENT ORIENT THE SENSOR SO IT IS NOT STRAIGHT UP.
2 PRESSURE SENSOR HAS 1/8-27 PIPE THREAD, SEE ADDITIONAL LOCATION AND INSTALLATION INFORMATION IN THIS
SECTION.
3 ALTERNATIVE METHOD, CLAMP AROUND THE SENSOR BODY (ITEM 1)
4 EITHER ALUMINUM OR STEEL FITTINGS ARE ACCEPTABLE. REFER TO APPLICABLE STANDARD FOR MATERIAL OPTIONS.
5 IF HOSE OR TUBING IS PREVIOUSLY INSTALLED, USE APPROVED AIRCRAFT FITTINGS (E.G. AN/AS-SPECIFICATION OR
MIL-SPEC) TO CONNECT THE SENSOR
Figure 6-10 – GPT Pressure Sensor (Housing & Coupling Mount Examples)
Page 85
6.6.1.2 Oil Temperature
When installing the oil temperature sensor, the unbroken side of the crush washer must face the sensor
flange. The sensor is torqued finger tight plus one-half turn and safety wired in accordance with practices
defined in Section 7, Safetying, of Chapter 7, Aircraft Hardware, Control Cables and Turnbuckles, of advisory
circular AC 43.13-1B, Aircraft Inspection and Repair.
6.6.1.3 Carburetor Air Temperature

The sensor location will vary for different carburetors. Reinstall the carburetor temperature sensor as
described in Figure 6-11.
CAUTION
Fuel and air passages must remain free of contaminants during work near and around the
carburetor.
Figure 6-11 – Carburetor Air Temperature Sensor Mounting
6.6.1.4 Fuel Flow

The fuel flow transducer may be mounted with a bracket or clamps on the hoses. Reinstall the fuel flow
transducer as follows:
• Install the mounting clamps (if used) within six inches of the nearest face of the transducer.

Page 86
• Install it with the fuel flow direction matching the direction marked on the ports and the wires are not
pointing downward.
• Ensure the hose connected to the IN port are straight for a minimum of four inches.
• Ensure the length of hose connected to the OUT port should be level or slope up. It must not slope
down more than four inches per foot.
The hoses and fittings connected to fuel flow transducer must meet the following requirements:
• Fuel hoses must not be subject to engine or other movement that could loosen the fittings.
• Replacement hoses must have the same internal diameter as the hose being replaced and meet
TSO-C53a Type C or D fire resistant specifications.
• Use fuel compatible thread sealant for the NPT threads. To reduce the risk of fuel system
contamination, a minimal amount of sealant should be applied, leaving at least two threads at the
end of the fitting clear of sealant. Before connecting any hoses, thoroughly clean and flush the
transducer and hoses to insure they are free of any loose material.
• Fitting torque must not exceed 12 ft-lbs., or two full turns past finger tight, whichever occurs first.
• Install the transducer and fuel hoses routed as far away from the aircraft exhaust system as
practical. Securely wrap and the transducer with Aeroquip AE102-( ) fire-sleeve if within six inches
of any exhaust component.
• Line fittings, routing, alignment, bonding, and support spacing must be installed as defined in the
aircraft maintenance manual or section 8-31 of AC 43.13-1B, “Aircraft Inspection and Repair”.
WARNING
Ensure the fuel flow transducer installation does not introduce thread sealant or debris into the fuel system.
CAUTION
Do not blow pressurized air through the flow transducer.

Page 87
Figure 6-12 – Fuel Flow Transducer Installation Example
6.7 GAD 29B/29D ARINC 429 Adapter
Removal:
1. Gain access to the GAD 29B/29D. Refer to the location information recorded in APPENDIX A of this
2. Disconnect the GAD 29B/29D connectors.
3. Remove the four screws that hold the GAD 29B/29D to the mounting location.
4. Lift the GEA 24(B) off its mounting location.
Reinstallation:
1. Place the GAD 29B/29D in its mounting location and align its holes with the mounting holes.
2. Insert the four mounting screws and secure the GAD 29B/29D in place.
3. Inspect the electrical connectors and pins for signs of damage. Repair any damage.
4. Connect the wiring harness to the GAD 29B/29D.

Page 88
4X #8 SCREWS
GAD 29B
EXISTING OR
FABRICATED
SHELF 4X #8 WASHERS
& 4X #8 NUTS
OR
4X #8 MIL-SPEC
NUTPLATES
Figure 6-13 – GAD 29B/29D
6.8 GDL 5XR Datalink

Removal:
1. Gain access to the GDL 5XR. Refer to the location information recorded in APPENDIX A of this
2. Disconnect the GDL 5XR electrical and coax cable connectors as applicable.
3. Remove the four screws that secure the GDL 5XR to the mounting location.
4. Lift the GDL 5XR off the mounting location.
Reinstallation:
1. Place the GDL 5XR in its mounting location and align its holes with the mounting holes.
2. Insert the four mounting screws and secure the GDL 5XR in place with washers and nuts (as
appropriate).
4. Connect the electrical and coax connectors as applicable to the GDL 5XR.
5. Continue to Section 7.8 for configuration and checkout procedures.

Page 89
4X #6 SCREWS
4X #6 WASHERS
GDL 5XR
EXISTING OR
FABRICATED
SHELF
4X #6 WASHERS
&
4X #6 NUTS
OR
4X #6 MIL-SPEC
NUTPLATES
Figure 6-14 – GDL 5XR (GDL 52R Shown)
6.9 GPS Antenna (P/N 011-04036-00 or 011-04036-10)

Removal:
1. Remove power from the aircraft.
2. Disconnect the GPS antenna coax cable from the back of the PFD.
3. Remove the screws (if applicable) or pull on antenna to separate the fastener tape (hook & loop
material) securing the antenna on the glareshield.
4. Lift up on the GPS antenna from the glareshield to remove it.
Reinstallation:
1. Place the antenna on the mounting location on the glareshield.
2. Secure the antenna as applicable with screws or hook & loop material.
3. Connect the GPS antenna coax cable to the back of the PFD.
4. Coil any excess coax cable and secure with cable ties.
5. Conduct return to service procedures in Section 8 as applicable.

Page 90
Figure 6-15 – GPS Antenna (Screw-mounted Installation Example)

Page 91
Figure 6-16 – GPS Antenna (Hook and Loop Installation Example)
6.10 GTR 20 Remote-Mount VHF COM

Removal:
1. Gain access to the GTR 20. Refer to the location information recorded in APPENDIX A of this
2. Disconnect the GTR 20 electrical and coax connectors.
3. Remove the four screws, washers and nuts (as applicable) that secure the GTR 20 to the mounting
location.
4. Remove the GTR 20 unit.
Reinstallation:
1. Place the GTR 20 in its mounting location and align its holes with the mounting holes.
2. Insert the four mounting screws and secure the GTR 20 in place with washers and nuts or nutplates
as applicable.
4. Connect the electrical and coax connectors to the GTR 20.
5. Continue to section 8 for configuration and checkout procedures

Page 92
4X #10 SCREWS
4X #10 WASHERS
GTR 20
EXISTING OR
FABRICATED SHELF
4X #10 WASHERS
&
4X #10 NUTS
OR
4X #10 MIL-SPEC NUTPLATES
Figure 6-17 – GTR 20 VHF COM Radio
6.11 GTR 200B VHF COM Radio

Removal:
1. GTR 200B is installed on the instrument panel in a rack.
2. Insert a 3/32” hex drive tool into the access hole on the lower right corner of the face of the unit.
3. Turn the tool counterclockwise until it stops.
4. Pull the unit from the rack.
Reinstallation:
1. Slide unit into the rack or panel cutout until it stops.
2. Insert a 3/32” hex drive tool into the access hole on the lower right corner of the face of the unit.
3. Push on the GTR 200B bezel while turning the tool clockwise until the unit is securely seated in the
rack. Do not exceed 15 in-lbs. of torque.
4. Continue to Section 8.14 for configuration and checkout procedures.
6.12 GMA 245R w/Marker Beacon Audio Panel

Removal:
1. Gain access to the GMA 245R. Refer to the location information recorded in APPENDIX A of this
2. Disconnect the GMA 245R connectors.
3. Remove the six screws, washers and nuts (as applicable) that secure the GMA 245R to the mounting
location.

Page 93
4. Remove the GMA 245R unit.
Reinstallation:
1. Place the GMA 245R in its mounting location and align its holes with the mounting holes.
2. Insert the six mounting screws and secure the GMA 245R in place with washers and nuts or nutplates
as applicable.
3. Inspect the electrical connectors to ensure there are no bent or damaged pins. Repair any damage.
4. Connect the electrical connectors to the GMA 245R.
6X #10 SCREWS
6X #10 WASHERS
GMA 245R
EXISTING OR FABRICATED
SHELF
6X #10 WASHERS AND

6X #10 NUTS,
OR
6X #10 MIL-SPEC NUTPLATES
Figure 6-18 – GMA 245R Audio Panel
6.13 GAP 26 AOA Probe

Removal:
1. Locate the GAP 26 AOA probe on the underside of either wing. Place an aligning mark on the
inspection panel and wing to allow correct reinstallation.
2. While supporting the AOA probe, remove the screws from the inspection panel attached to the
probe.
3. Carefully lower the probe from the wing and while supporting the AOA probe, disconnect AOA tube
from tube inside wing and the electrical wires from the mechanical splice. Shown below is splice if 10
AWG wire is used on 14-volt aircraft.

Page 94
0.5(±0.1)" 0.5(±0.1)"
MS3367 CABLE TIES
TO AIRCRAFT POWER
TO GAP26
AND GROUND
FIBERGLASS SLEEVE
Figure 6-19 – GAP 26 Mechanical Splice Detail (14-volt Aircraft with 10 AWG Wire)
4. With the probe disconnected from the aircraft, place an aligning mark on the probe and mount
bracket to ensure it is reinstalled in the correct orientation.
5. Remove the four screws from the mount tube to separate from the probe.
NOTE
AOA and pitot tubes are flexible and may require straightening to allow to slide out of the mount
tube.
6. Pull the probe from the mount tube.

Reinstallation:
1. Insert probe on the mount tube and align its holes with holes on the mount tube. Ensure the mark on
the probe aligns with mark on mounting tube.
2. Insert the four mounting screws and secure the GAP 26 probe on mount tube.
3. While supporting the inspection panel with probe assembly, connect the mechanical splice and AOA
tube to tube inside the wing.
NOTE
Ensure pitot tube is capped, reference G3X Touch EFIS Part 23 AML STC Installation Manual
(190-02472-01) for details.
4. Ensuring proper orientation of the inspection panel and AOA probe assembly on the wing, insert the
screws on the inspection panel holes and secure to aircraft structure.

Page 95
4X #8 NUTS
4X #8 WASHERS
22 AWG RING TERMINAL-REF

(AS NECESSARY)
2X #6 SCREWS
2X #6 NUTS
2X #6 WASHERS
2X #6 WASHERS
INSPECTION PANEL
4X #8 SCREWS
MOUNT TUBE BRACKET
117-00659-10
4X #6 SCREWS
MOUNT TUBE
117-00658-10
GAP 26
011-02964-70
Figure 6-20 – GAP 26 AOA Probe Assembly
6.14 EIS Annunciator Lights

There are two indicator lights one with a red lens and one with amber lens and must not be interchanged.
Remove and replace/reinstall one light at time to prevent swapping them
CAUTION
To avoid erroneous indication of the EIS gauges, the position of each color-coded lens must be noted and
reinstalled in its original position. Reference the G3X Touch Part 23 AML STC Installation Manual (190-
02472-01) for the correct location of each indicator.
Removal
1. Locate the EIS annunciator lights on the instrument panel. Ensure the forward side of the instrument
panel is accessible.
2. Loosen and remove the lens holder from the assembly and note the position of each on the
instrument panel.
3. While holding the jam nut on the forward side of the instrument panel, loosen and remove the jam nut
and washer on the aft side of the instrument panel (lens side).
4. Pull the indicator forward away from the instrument panel.
Reinstallation:

Page 96
1. Insert the indicator from the forward side of the instrument panel.
2. While supporting the jam nut and pushing the indicator against the panel, insert the washers and nut
on the indicator.
3. Fasten the nut on the aft side of the panel against the lock washer.
4. Install and secure the lens holder on the indicator.
6.14.1 EIS Annunciator Lamp Replacement.

1. Loosen the remove the lens holder.
2. Pull the lamp from base flange on the opposite end of the lens.
3. Install new lightbulb 28 VDC P/N MS25237-327 (GE or JKL lamp number 327) or 14 VDC P/N
MS25237-330 (GE or JKL lamp number 330 in the lens holder.
4. Install and secure lens holder on the indicator.

Page 97
7. G3X EQUIPMENT CONFIGURATION & TESTING
This section provides procedures to be performed after a G3X unit is removed and reinstalled or
replaced. At the beginning of each LRU section, instructions are given to guide the technician for various
removal/replacement scenarios. These instructions define necessary procedures to be followed for
situations where original equipment was reinstalled as well as for situations where new equipment (new
serial number) is installed.
7.1 GDU 4X0

Original GDU 4X0 is Reinstalled
No software or configuration loading is required if an original GDU 4X0 is reinstalled. This does not
include units that were returned for repair as their software and configuration files are deleted during the
repair testing process. Continue to Section 7.1.3.
New, Repaired, or Exchanged GDU 4X0 is Installed
If a new, repaired, or exchange GDU 4X0 is installed, the correct software must be loaded to the unit.
Continue to Section 7.1.2.
7.1.1 New PFD Configuration Module Installed

If a new configuration module is installed and no change is made to the PFD, the required configuration
information will be written to the new module by the PFD. If both the PFD and configuration module are
replaced with new modules, configuration of the system is required. Reference Section 5 of G3X Touch
EFIS Part 23 AML STC Installation Manual (190-02472-00) for configuration information.
NOTE
Do not use a used GDU configuration module as a replacement. Data that may reside on a used
configuration module may cause system configuration errors.
7.1.2 GDU Software Loading

Continue to section 7.13 for GDU software loading procedures.
7.1.3 GDU Display Testing

1. Apply power to the aircraft and allow the displays to initialize for approximately one minute. Verify
proper display of data and no red-x’s.
2. If no other service is to be performed, continue to the return-to-service procedures in Section 8.
7.2 GSU 25D ADAHRS and GMU 11 Magnetometer

Original GSU 25D is Reinstalled
No software or configuration loading is required if the removed GSU 25D is reinstalled.
New, Repaired or Exchange GSU 25D is Installed
If a new, repaired or exchange GSU 25D is installed, the correct software will be loaded automatically by
the G3X GDU when power is applied to the system.
Original GMU 11 is Reinstalled
No software or configuration loading is required if the removed GMU 11 is reinstalled. Continue to
Section 7.2.1.

Page 98
New, Repaired, or Exchange GMU 11 is Installed
If a new, repaired, or exchange GMU 11 is installed, the correct software will be loaded automatically by
the G3X GDU when power is applied to the system. Continue to Section 7.2.1.
7.2.1 GSU 25D/GMU 11 Testing and Calibration

Table 7-1 describes the calibration procedures to be performed for GSU 25D and/or GMU 11 units after
maintenance is performed.
For new GSU 25D and/or GMU 11, or if the mounting bracket/shelf and/or pitot/static/AOA lines have
been disturbed, perform the following tests/procedures.
1. Perform a pitot-static leak check in accordance with the aircraft manufacturer’s specification
and/or applicable regulations.
CAUTION
To avoid damaging the ADAHRS pressure sensors, the pitot and static and GAP 26 (if installed)
must all be connected to the test set. Note that the GAP 26 has drain holes on the underside of
the probe which must be covered during the test.
NOTE
If excessive leakage is detected while the test set is connected to the GAP 26, verify that
there are no leaks where the test set connects to the AOA port or drain hole. If the test set
connection also includes the GAP 26 pitot opening, verify that it covers the pitot drain hole as
well. Verify that the unused pitot line coming out of the GAP 26 is securely capped in
accordance with the G3X Touch EFIS Part 23 AML STC Installation Manual (190-02472-01).
If leakage is still suspected from the GAP 26, disconnect the probe from the AOA line and
connect the test set directly to the AOA line (or directly to the AOA port on the GSU 25D).
2. Pitch/Roll Offset Compensation by Aircraft Leveling (Section 7.2.1.1)

3. Magnetometer Calibration (Section 7.2.1.2).
4. Magnetometer interference test (Section 5.4.4)
• The addition, removal, or modification of components that are ferrous (magnetic), or
electrical changes to the installation that affect components within 10 feet of the GMU 11
magnetometer location after the Magnetometer Interference Test (Section 8.13.1) or
Magnetometer Calibration (Section 7.2.1.2) were completed, requires a repeat of the
Magnetometer interference test procedures. If new magnetic interference is detected, it
must be resolved, then the Magnetometer Calibration (Section 7.2.1.2) must be repeated.
5. Altimeter Check (Section 8.13.1).
• If the altimeter check (Section 8.13.1) fails, ADAHRS Static Pressure Calibration (Section
7.2.1.3) must be performed.
6. Engine run-up vibration test (Section 7.2.1.4).
7. Compass swing (Section 8.13.3). Must be performed after magnetometer calibration to verify the
ADAHRS/GMU 11 heading accuracy.
NOTE
For a new GSU 25D or GMU 11 and if the mounting screws that secure the mounting rack is loosened for
any reason affecting the orientation of the unit, ADAHRS Unit Orientation and Magnetometer Orientation
respectively, must be repeated in accordance with the G3X Touch EFIS Part 23 AML STC Installation
Manual (190-02472-01).

Page 99
Table 7-1 – GSU 25D/GMU 11 Recalibration Criteria
Calibrations Required
Engine Run-
GSU Pitch/Roll GSU 25D/GMU 11 up
Condition Offset Magnetometer
Vibration
Calibration Calibration
Test
GMU 11 was removed and reinstalled. (no None Required.

change in serial number) Continue to GSU 25D/GMU 11 Checkout Procedures
GMU 11 was replaced with new unit.

X
(New serial number)
GSU 25D was removed and reinstalled.

The mounting bracket was NOT removed, None Required.
and the mounting bracket bolts were NOT Continue to GSU 25D/GMU 11 Checkout Procedures
loosened. (same serial number)
GSU 25D was removed and reinstalled.

The mounting bracket WAS removed
and/or mounting bracket bolts WERE X X X
loosened.
GSU 25D was replaced with new unit.

X X X
(New serial number)
7.2.1.1 Pitch/Roll Offset Compensation by Aircraft Leveling
NOTE
Prior to performing the following procedure, the aircraft must be leveled using the procedures in the
aircraft maintenance manual.
Figure 7-1 – Aircraft Level Attitude

Use the following procedure to set GSU 25D pitch and roll compensation on the aircraft;
1. Select the ADAHRS Calibration Page.
2. Ensure that all the required status boxes are checked.
3. Select Pitch/Roll Offset.
4. Ensure that aircraft and ADAHRS comply with all on-screen instructions, then select the START
button.

Page 100
5. “Pitch/roll offset calibration in progress” will appear on the display along with calibration
information.
Figure 7-2 – Pitch/Roll Offset Calibration in Progress
NOTE
The GSU 25D pitch/roll offset procedure has a 30 second countdown timer that resets if the aircraft
moves.
6. When the calibration has completed “Success” or “Failure” will be displayed; select the DONE
softkey to return to the ADAHRS Calibration screen.
Figure 7-3 – Pitch/Roll Offset Completion Status
NOTE
Magnetometer Calibration must be completed after each ADAHRS pitch/roll offset calibration.
NOTE
The subsequent ADAHRS and magnetometer procedures are carried out with the aircraft engine
running. Start and operate the aircraft engines in accordance with Pilot’s Operating Handbook (POH) or
Aircraft Flight Manual (AFM).
7.2.1.2 Magnetometer Calibration
NOTE
The Pitch/Roll Offset Compensation procedure in section 7.2.1.1 must be completed prior to performing
this procedure.

Page 101
Use a compass rose or calibrated magnetic sight compass to calibrate the magnetometer. Ensure that
the aircraft and compass are located away from magnetic interference sources including buildings. The
accuracy of the ADAHRS cannot be guaranteed if the calibration is not performed in an area that is free
of metallic structure or objects.
With the aircraft stationary, initiate the magnetometer calibration procedure as follows:
1. Start the aircraft engine per the POH/AFM.
2. Taxi the aircraft to a desired calibration area.
NOTE
Ensure that there are no nearby magnetic materials on or near the perimeter of the site. If unavoidable,
maneuver the aircraft to keep the magnetometer from passing within 20 feet of such objects. Ensure
that vehicles or other aircraft are a minimum of 40 feet away from the aircraft during this procedure.
3. At the site, align the aircraft to a heading of magnetic north (+/- 5°). It is best to offset the aircraft
position to the left (west) of the North/South axis to allow turning clockwise around the site as
indicated below.
Figure 7-4 – Compass Rose Starting Position

4. Power on the display(s) in Configuration Mode.
5. Select the Magnetometer Calibration Page.
6. Select Magnetometer Calibration.
7. Ensure that all on-screen instructions have been complied with and select the Start button to
begin the calibration.

Page 102
Figure 7-5 – Magnetometer Calibration On-Screen Instructions
8. Follow the on-screen instructions, the dots at the end of the text will be removed as the test
progresses.
Figure 7-6 – Magnetometer Calibration Progress

9. Follow the on-screen instructions by slowly turning the aircraft to the right, the dots at the end of
the text will be removed as the aircraft rotates 30 degrees. When all dots have been removed,
and the text changes to ‘Hold Position’, stop turning the aircraft, and wait for further instructions.
10. Continue following the on-screen instructions until the calibration is completed. The calibration
will go through twelve cycles of holding, then turning to the right, before completing a full circle.
11. When the calibration is finished, ensure that a Calibration Status of “Success” is displayed, then
press the Done softkey to return to the Magnetometer Configuration Page.
NOTE
If smooth accurate turns are not made, the ADAHRS may incorrectly interpret a station and instruct to
“Hold current position…” prior to or after completion of the heading change. If this scenario is
encountered, it is best for the operator to temporarily ignore the “Hold current position…” command and
instead use compass rose references to complete the heading change. Dwelling at these 30° increments
for the time recommended by the ADAHRS should result in successful calibration.
7.2.1.3 ADAHRS Static Pressure Calibration
The ADAHRS Calibration page, in configuration mode, has a selection for ADAHRS Static Pressure
Calibration. This procedure is used to perform an altimeter re-calibration.

Page 103
NOTE
This calibration is only used when an ADAHRS fails a periodic altimeter test and should only
rarely, if ever, be used. Prior to using this procedure, all possible sources of leakage in
pneumatic lines, fittings, and GAP 26 should be ruled out (if necessary, connect the test set
directly to the pitot/static/AOA ports on the GSU 25D to verify).
The static pressure calibration requires the use of a pressure control system (test set) with an altitude
accuracy of at least +/- 5 ft at sea level and +/- 20 ft at 30,000 ft. It is necessary to re-calibrate to sea
level (0 ft), 10,000 ft, 20,000 ft, and optionally to 30,000 ft. Calibration to 30,000 ft is only required for
aircraft that may reach that displayed altitude.
CAUTION
To avoid damaging the ADAHRS pressure sensors, the pitot and static ports and GAP 26 (if
installed) must be connected to the test set. Note that the GAP 26 has drain holes on the
underside of the probe which must be covered during the test.
1. Connect the pressure test set to the pneumatic ports on the aircraft skin.
2. Power on the PFD in configuration mode if it is not already in configuration mode.
4. Select Static Pressure Calibration.
Figure 7-7 – Static Pressure Calibration

5. Select “OK” to continue the calibration.
Figure 7-8 – Static Pressure Calibration Warning

6. Ensure that all on-screen instructions have been complied with and all information displayed is
correct, then select the “Start” button to begin the calibration.

Page 104
Figure 7-9 – Static Pressure Calibration Instructions
7. At each calibration point (sea level, 10K, 20K, and optionally 30K ft), the display will present a
screen that allows time to establish the calibration pressure before continuing.
Figure 7-10 – Static Pressure Calibration in Progress

8. Select “Next” to continue and calibrate each pressure.
9. During the calibration at each pressure, the pressure must be held constant for 30 seconds for
the calibration step to be successful. The calibration may be cancelled at any point should the
test setup require adjustment before repeating.
10. When the static pressure calibration is complete, a status screen will show that the procedure
was successful.
Figure 7-11 – Static Pressure Calibration Completion Status
7.2.1.4 Engine Run-up Vibration Test
NOTE
The Engine Run-Up Vibration Test is required for all installations to validate the vibration characteristics of
the installation. The ADAHRS Unit Orientation and Pitch/Roll Offset Compensation (Section 7.2.1.1) are
not required prior to this procedure.
1. Power on the PFD in configuration mode if it is not already in configuration mode.

3. Ensure that all the required status boxes are checked.
4. Select Engine Run-Up Test.
Page 105
5. Ensure that the aircraft has been properly positioned per the on-screen instructions, then select
the Start button to begin the test.
6. Gradually increase power from idle to full-throttle and back to idle over the course of one to two
minutes; the test data is displayed as the test progresses.
NOTE
If failures are indicated, the engine run-up test may be repeated up to three times. If the test does not
pass after three attempts, the installation should be considered unreliable until the source of the
vibration problem is identified and remedied. If the engine run-up test fails repeatedly, record the values
that are reported to be out of range for future reference.
7. Select the Done softkey when engine run-up has been completed; the test results will be
displayed.
8. Ensure that test results indicate Passed, then select the Done button to return to the ADAHRS
page.
The following are potential causes for failure of the engine run-up test:
• Excessive flexing of GSU 25D with respect to airframe.
• Vibration or motion of the GSU 25D caused by neighboring equipment and/or supports.
• Mounting of GSU 25D at a location that is subject to severe vibrations such as near engine
mounts.
• Mounting screws and other hardware for GSU 25D and/or GMU magnetometer not properly
attached.
• GSU 25D connector not firmly attached to unit.
• Absence of recommended mounting support.
• Cabling leading to the GSU 25D not firmly secured to supporting structure.
• An engine/propeller combination that is significantly out of balance.
NOTE
Some aircraft may have difficulty passing this test if performed in windy conditions. Windy conditions do
not provide evidence that the test would otherwise pass successfully; an actual pass is required before
the installation can be considered adequate.
7.3 GMU 11 Magnetometer
Reference Section 7.2.
7.4 GTP 59 Temperature Probe

Original GTP 59 Reinstalled
No software or configuration loading is required when an original GTP 59 is reinstalled.
New, Repaired, or Exchange GTP 59 Installed
If a new, repaired, or exchange GTP 59 is installed, no software or configuration required.
7.4.1 GTP 59 Testing

1. Verify OAT operation by observing the PFD for a valid value for OAT.
2. Apply heat to the GTP 59 probe and observe OAT value rises by at least 5º Celsius.
7.5 GAD 27
Original GAD 27 Reinstalled

Page 106
No software or configuration loading is required if the removed GAD 27 is reinstalled. Continue to
Section 7.5.1.
New, Repaired, or Exchange Display(s) Installed
If a new, repaired or exchange GAD 27 is installed, the correct software will be loaded automatically by
the G3X GDU when power is applied to the system.
7.5.1 GAD 27 Testing

Apply power to the aircraft and with all the circuit breakers closed, ensure is not displayed on
the GDU.
7.6 GEA 24(B) Engine and Airframe Unit

Original GEA 24(B) Reinstalled
No software or configuration loading is required if the removed GEA 24(B) is reinstalled. Continue to
Section 7.6.1
New, Repaired, or Exchange GEA 24(B) Installed
If a new, repaired or exchange GEA 24(B) is installed, the correct software version and EIS configuration
will be loaded automatically by the G3X GDU when power is applied to the system. Continue to Section
7.6.1.
NOTE
For most interfaces the GEA 24 and GEA 24B are interchangeable with the same wiring and
configuration settings, however the GEA 24 interface to resistive fuel probes must use a pair
of 2.2kΩ resistors and be configured as ‘Voltage’ interfaces (refer to Garmin SB 2134 and
Installation Manual Rev.9 or later). If a GEA 24 is replaced by a GEA 24B, any fuel quantity
interfaces to resistive probes must be recalibrated regardless of whether the 2.2kΩ resistors
in the harness are retained or removed. For new installations with a GEA 24B, the resistors
are not required, reference the STC Installation Manual Rev 14 (or later).
7.6.1 GEA 24(B) Test

Verify all engine instruments are displayed and indicate valid values and markings. Reference Section
8.12 for checkout procedures.
7.7 GAD 29B/29D

Original GAD 29B/29D Reinstalled
No software or configuration loading is required if the removed GAD 29B/29D is reinstalled. Continue to
Section 7.7.1.
New, Repaired, or Exchange GAD 29B/29D Installed
If a new, repaired or exchange GAD 29B/29D is installed, the correct software version will be loaded
automatically by the G3X GDU when power is applied to the system. Continue to Section 7.7.1.
7.7.1 GAD 29B/29D Testing

Verify external LRUs that are connected to the GAD 29B/29D such as compatible navigators and non-
Garmin autopilots are operating as intended:
1. GPS receiver check (Section 8.3)
2. Nav receiver check (Section 8.4)
3. Non-Garmin Autopilot interface check (Section 8.16)
7.8 GDL 5XR

Page 107
Original GDL 5XR Reinstalled
No software or configuration loading is required if the removed GDL 5XR is re-installed. Continue to
Section 7.8.1
New Repaired or Exchange GDL 5XR Installed
If a new repaired or exchange GDL 5XR is installed, the software will be loaded to the unit automatically
by the G3X GDU when power is applied to the system. Continue to Section 7.8.1
7.8.1 GDL 5XR Functional Check

Perform functional tests as applicable in Section 8.
1. Activate SiriusXM Radio and Weather (Section 7.14) – for newly installed GDL 51R/52R.
2. ADS-B Traffic interface check (Section 8.5) (GDL 50R/52R).
3. GDL 51R/52R SXM weather check (Section 8.10).
4. GDL 51R/52R SXM audio interface check (Section 8.11).
7.9 GTR 20 Remote-Mount VHF COM
Original GTR 20 Reinstalled
No software or configuration loading is required when an original GTR 20 is reinstalled.
New, Repaired, or Exchange GTR 20 Installed
If a new, repaired, or exchange GTR 20 is installed, the software will be loaded to the unit automatically
by the G3X GDU when power is applied to the system.
7.10 GTR 200B VHF COM
Original GTR 200B Reinstalled
No software or configuration loading is required when an original GTR 200B is reinstalled.
New, Repaired, or Exchange GTR 200B Installed
If a new, repaired, or exchange GTR 200B is installed, the software will be loaded to the unit
automatically by the G3X GDU when power is applied to the system.
7.10.1 GTR 200B Test

Verify proper operation of the GTR 200B audio panel. Reference Section 8.14 for checkout procedures.
7.11 GMA 245R Audio Panel
Original GMA 245R Reinstalled
No software or configuration loading is required when an original GMA 245R is reinstalled.
New, Repaired, or Exchange GMA 245R Installed
If a new, repaired, or exchange GMA 245R is installed, the software will be loaded to the unit
automatically by the G3X GDU when power is applied to the system.
7.11.1 GMA 245R Test

Verify proper operation of the GMA 245R audio panel. Reference Section 8.5 for checkout procedures.
7.12 GAP 26 AOA Probe

Original GAP 26 Reinstalled
No software or configuration loading is required when an original GAP 26 is reinstalled.
New, Repaired, or Exchange GAP 26 Installed

Page 108
If a new, repaired, or exchange GAP 26 is installed, no software or configuration required.
7.12.1 GAP 26 Testing

Reference Section 8.18 for checkout procedures.
7.13 G3X Software Information
All software files are certified by Garmin and are considered part of FAA-approved Type Design data.
System software version 8.00 and later are approved for this STC.
The installer shall create this software loader card by downloading the approved software image in
accordance with Section 7.13.1.
NOTE
G3X system software loaded via the GDU includes the latest approved software for all G3X
LRUs and also includes software for the G5 standby instrument, GSA 28 autopilot servos, and
the GMC 507 mode controller. The GTR 200B features a dedicated microSD slot for software
updates, however this should not be used to load software when installed with G3X. If the G5
AML STC (SA01818WI) has an approved software version that is later than the one included
with the G3X software, the later software version can be loaded directly into the G5 standby
instrument.
NOTE
Only SanDisk brand 8GB SD cards or smaller are recommended for use with the G3X
system. If another brand of card is used and software loading problems occur, replace the
card with a SanDisk brand card and reattempt the software load.
7.13.1 Software Loader Card Creation

The software image is an executable self-extracting file which builds the correct file structure onto an SD
card for use in loading software to the G3X. To obtain the current file, follow the procedures outlined
below.
1. Go to www.garmin.com and navigate to the G3X Touch for Certificated Aircraft page, then click
on the ‘Software’ link. Do not download software from the Experimental Aircraft web page.
2. Insert a FAT32-formatted (empty) SD card in to the card reader.
3. Double-click the .exe file to download the self-extracting update file onto the hard drive. A window
similar to the image below will pop-up while extracting.
NOTE
When the extraction begins, the program automatically deletes all current files on the SD
card and copies the selected files to it, regardless of the file format on the SD card. Ensure
files are not necessary or card is empty before proceeding.
Page 109
4. When extraction is complete, a window similar to one below will appear on the screen. Verify
“GDU 4xx” is correct and an SD card is in the card reader, and then select “Next”. Follow
instructions provided by the installer application.
5. Select from the drop-down list the correct drive letter of the SD card to be used for the update.
Click next.
Select drive
6. A window will pop-up on the screen to indicating file progress.

Page 110
7. Once successfully completed, a message/window similar to below will pop-up. Click Finish to
finalize SD card.
8. Remove SD card from card reader.

NOTE
If necessary, ‘eject’ or un-mount the SD card prior to removal.

7.13.2 Software Loading Procedure
Software loading is performed in normal mode. Obtain the software loader card as formatted and loaded
with software per section 7.13.1. This section describes the procedures needed to load software to
Garmin LRUs as part of configuring the G3X system for use.
NOTE
Perform software updates on the ground only and remain on the ground while a software update is in
progress
7.13.2.1 GDU Software Loading Procedure

1. Connect external power to the aircraft to energize the aircraft and avionics electrical busses.

Page 111
CAUTION
DO NOT RELY ON THE AIRCRAFT BATTERY TO LOAD SOFTWARE. DO NOT USE A BATTERY
CHARGER AS AN EXTERNAL POWER SOURCE. Power loss during a software upgrade may cause an
LRU to become corrupted and unresponsive requiring replacement.
2. Power on the PFD in normal mode, then insert the properly formatted SD card into the SD card
slot.
NOTE
It is also acceptable to insert the SD card before powering on the unit.

3. A Software update window will appear on the screen; select YES to begin the update. Figure
7-12 is an example image and may not represent the current software version.
Figure 7-12 – Update Software Window (Example)

4. The unit will reboot, then GDU software update will begin automatically.
5. Ensure power is not removed while the update is being performed. The screen will display
progress of the software load.
6. The unit will reboot after the update is complete.
7. Software update of other G3X LRUs will begin and a “Software update in progress- Do not
remove power” message will be displayed on the message window. Touch to view
message and progress. The message will be removed once software loading to G3X LRUs is
completed.
8. Repeat steps 1 through 5 on all other installed GDUs. A “GDU software version mismatch”
message will be displayed until software has been loaded on all GDUs .
7.13.2.2 LRU Software Loading Information

G3X LRUs (except for GDUs) will automatically receive software updates from the PFD following a
software update. Software for the G5 standby instrument, GSA 28 autopilot servos, and GMC 507
autopilot mode controller (if installed) is also updated automatically by the PFD. This process may take
up to ten minutes for all LRUs connected to the high-speed CAN bus. The GDL 5XR is connected via
RS-232 and may take up to 30 minutes to update software.
NOTE
Approved software for PMA GDL 5XR units can only be loaded via the G3X GDU. The ability
to update GDL 5XR software via Bluetooth connections has been disabled for PMA GDL 5XR
units.
Page 112
Progress of LRU software updates can be monitored using the System Information page in configuration
mode. In normal mode, touching the flashing amber ‘Message’ indication at the bottom of the GDU will
bring up a system message ‘Software update in progress – Do not remove power’ which will persist until
all LRU software updates are complete. Functionality provided by an LRU will be unavailable during a
software update, therefore, all LRU software updates should be allowed to complete before flight after a
GDU software update.
The current LRU software versions included with a GDU software update can be found in the change
notes on the software download page.
7.13.3 Software Load Confirmation

Perform software load confirmation after the software has been loaded to the G3X GDU(s) and LRUs.
1. Start the G3X GDUs in configuration mode (reference Section 3.2.2) as required.
2. Use the Touch Panel or a Move Selector Knob to select and view the System Information Page.
3. Ensure there is a green checkmark next to all installed G3X LRUs.
4. Scroll the Device List box and select device’s info by using the Touch Panel or a Move Selector
Knob as necessary to verify the software and version numbers installed in the system.

Page 113
7.14 Activation of GDL 51R/52R SiriusXM Radio and Weather
Before SiriusXM Weather and Radio is accessed, service must be activated by SiriusXM. Service is
activated by providing SiriusXM with a Radio ID. Following the following activation steps.
Activation Steps
1. Contact SiriusXM at 1-855-796-9847 or at www.siriusxm.com/sxmaviation to activate.
2. Obtain the Radio ID from the data tag on the unit or from the Datalink page in normal mode. To
access the datalink page on the GDU, press “MENU” key twice for the main menu, then select
Data Link.
3. Position the aircraft in an area with an unobstructed view of the southern sky. It is highly
recommended that the aircraft be positioned outside and at least twenty five feet away from the
hangar.
4. Connect an external power unit and apply power to the aircraft and avionics.
5. Navigate to the Data Link page in the main menu section and verify signal quality has green bars.
6. When the subscribed product is displayed by “Service Level”, the activation is complete. For
example, in the screenshot below “Pilot Pro” is the subscribed product.
NOTE
Do not remove power from the aircraft during the activation process.
Figure 7-13 – Data Link Page

Page 114
8. SYSTEM RETURN TO SERVICE PROCEDURE
This section provides checkout procedures to be completed after maintenance and/or repair has been
performed in accordance to this manual, in order to verify the proper operation and function of G3X Touch
systems.
Perform the procedures as applicable to the specific installation. Procedures not applicable may be
skipped.
8.1 Recommended Test Equipment

The following test equipment is recommended to conduct and complete all post installation checkout
procedures in this section:
• Ground power cart (capable of supplying power to the aircraft systems and avionics)
• Calibrated Air data test set
• Calibrated VHF NAV test set
• Low resistance ohmmeter
• Calibrated Digital Level
• Digital Multi-Meter (DMM)
• Calibrated Optical Tachometer
8.1.1 LRU Status and Software Check
Perform LRU status and software check. The “System Information” page in the configuration mode of the
GDU 4X0 PFD has a “Devices Online” tab that reports the status of installed LRU’s and their currently
installed software part numbers and versions. The icon/checkbox next to each LRU reports a green
checkmark, a ‘red x’ or blank checkbox to indicate the status of each LRU as described in Table 8-1.
To access the System Information Page, perform the following steps on the primary GDU:
1. In configuration mode, select the System Information Page. Scroll the Device List box and the
selected device’s info by using the Touch Panel or a Move Selector Knob.
2. Verify that all LRUs connected or configured to each display have a green indicator and correct
software part numbers and version numbers are reported.
3. Press the Back key to return to the Configuration Mode page when finished. Return the GDU to
normal mode.
Table 8-1 – LRU Status Indicators
Color LRU Condition
Green The LRU is online & no faults found.
Red ‘X’ The LRU is online & a fault, warning, or error has been detected.
Blank The LRU is not online.

Page 115
8.2 Transponder Check
The GNX 375, all GTX 335(R)/345(R) transponders, and GTX 33/33ES/330/330ES transponders with
software version 8.00 or later are compliant with RTCA/DO-181D, which specifies that the selection of
transponder ALT and GND modes may not be controlled by the pilot. To allow the transponder to be
operated in ALT mode while on the ground, for the purposes of performing periodic testing in accordance
with the requirements of 14 CFR Part 91.413, a special transponder ground maintenance test mode is
provided.
To access ground maintenance mode in a G3X Touch system:
1. Access the Transponder page, press the Menu key twice to access the main menu.
2. On the Main menu, select Setup to access setup page.
3. On the Setup page, select XPDR to access the transponder page.
4. On the transponder page, select “Enabled” under Ground Maintenance Test to force the
transponder into ALT mode.
Figure 8-1 – Transponder Setup Page (Normal Mode)

Transponder ground maintenance mode will be cancelled following a power cycle, or if the aircraft is
determined to be airborne.
8.3 GPS Receiver Check
8.3.1 GPS Receiver Signal Acquisition Test

The following steps constitute a simple test of the GPS receiver’s ability to acquire a GPS signal from
satellites. This test needs to be performed outside, away from obstructions such as buildings, unless a
known working GPS signal repeater has been installed in the hangar for this type of testing.
1. Power on unit in normal mode and select the Info Page.
2. Verify that the GPS receiver is functional and able to calculate its present position

Page 116
8.3.2 GPS Receiver COM Interference Test
NOTE
GPS Status may also be monitored on the Info page in normal mode. The signal
strength bars are a real-time representation of GPS signal strength which may be
useful for troubleshooting a failed COM interference test.
This test must be conducted outside, as the use of a GPS repeater inside a hangar may result in a failed
test. After the preceding signal acquisition test has been completed successfully, perform the following
steps:
1. Apply power to the aircraft and G3X system and allow systems to initialize and the G3X system
and/or GPS navigator (if installed) to acquire sufficient satellites for a GPS solution.
2. On the MFD (in dual GDU installations) or on the multi-function pane in split format mode (in a
single GDU (PFD) installation); navigate to the info page to view the GPS status.
3. Monitor GPS status on the Main Page. Possible GPS status indications include:
• No Antenna • Searching the Sky
• Autolocate • Acquiring
• Lost GPS Fix • No GPS Fix
• 2D GPS Fix • 2D Differential
• 3D GPS Fix* • 3D Differential*
*Indicates valid GPS position fix for this test
4. Select 121.150 MHz on the COM transceiver.
5. Transmit for a period of 30 seconds while monitoring GPS status.
6. During the transmit period, verify that GPS status does not lose a valid GPS position fix on the
Main Page in configuration mode.
7. Repeat steps 3 through 5 for the following frequencies:
• 121.175 MHz
• 121.200 MHz
• 131.250 MHz
• 131.275 MHz
• 131.300 MHz
8. Repeat steps 3 through 6 for other installed COM transceivers if applicable.
9. If an installed COM supports 8.33 MHz channel spacing, repeat steps 3 through 5 while
transmitting for a period of 35 seconds, for the following frequencies:
• 121.185 MHz
• 121.190 MHz
• 130.285 MHz
• 131.290 MHz
10. Repeat step 8 for other installed COM transceivers supporting 8.33 MHz channel spacing if
applicable.
This COM interference test should be repeated if a second GDU is installed in the aircraft and paired with
GPS antenna.

Page 117
8.3.3 GPS Receiver Interface Check
NOTE
GPS satellite reception is required for the following steps. Perform the test in an outdoor area
with a clear view of the sky. The check may also be performed in a hangar with a good known
GPS repeater.
1. Verify the PFD is in Normal mode.

2. On the PFD options page under FPL Source, select “External GPS”.
3. On the PFD options page under CDI Source, select “GPS” (or “GPS1”) as the navigation source.
4. Verify the external GPS1 Navigator is powered on and if dual GPS navigators are installed,
ensure the second GPS navigator (GPS2) is powered off.
a. For a GPS 175, GNX 375, GNS 4XXW/5XXW series or GTN 6XX/7XX series navigator,
while on the power-up self-test page, verify that the PFD CDI displays the correct lateral
and vertical deviation information.
b. For a GNS 480 unit, while it is going through its power-up sequence, verify that the PFD
CDI displays the correct lateral and vertical deviation information.
5. Continue in normal mode after self-test and wait until the navigator acquires a position before
proceeding.
6. Review the active alerts on the PFD (if any) and verify that there are no alerts, service soon, or
service required alerts associated with the GPS unit.
7. Create or activate a flight plan on the GPS navigation source.
8. Verify that the active waypoint displayed in the PFD WPT field of the GDU 4X0 is the same as the
active waypoint displayed on the navigator.
9. On the GPS navigator, enter OBS mode.
10. When OBS mode is entered on navigator, the course (CRS) field on the GDU will
activate and change to OBS on a lighter background , and knob that has been
configured for course will be activated to change the course.
11. Adjust the course (OBS) using the configured PFD knob. Course may also be changed using the
touch screen by pressing the OBS/CRS field and entering the value using the pop-up keypad.
12. Verify that the course to the active waypoint changes on the navigator as the PFD course pointer
is rotating.
13. Exit OBS mode on the navigator.
14. If dual GPS receivers are installed power off GPS 1 and power on GPS 2. Select GPS2 on the
CDI and repeat the GPS interface check (Steps 1-13).
8.4 NAV Receiver Check

1. Verify the external NAV1 receiver is powered on and if dual NAV receivers are installed, ensure
the second NAV receiver (NAV2) is powered off.
2. Tune the NAV receiver to a localizer frequency (it is not necessary that a valid localizer signal is
being received).
3. Verify that the CDI on the PFD displays “LOC” (or “LOC1”/“LOC2” for installations with dual
navigators). The CDI source field in PFD options page should also display “LOC” (or
“LOC1”/“LOC2”.
4. If dual navigation receivers are installed, power off NAV 1 and power on NAV 2.
5. Repeat the steps 2 through 4 above.

Page 118
8.5 Audio Panel Interface Check
An in-aircraft checkout may be performed in the aircraft on the ramp with known good microphone,
headset, and avionics receivers.
8.5.1 Alert Volume Check
This check is performed with GDU in configuration mode to verify proper alert volumes for alert, message,
AOA, and Alt Alert as applicable.
1. Apply power to aircraft with GDUs in configuration mode.
2. Connect a headset to the pilot’s headset output jack and pilot’s mic jack.
3. Navigate to the “Sound Configuration” page.
4. Select the “Test” button;
• Verify proper sound volume is heard on the headsets.
• Verify proper sound volume is heard on the cabin speaker (if installed).
5. Repeat step 4 for all applicable alerts.
8.5.2 Failsafe Operation Check
1. Remove power to the unit by pulling the AUDIO circuit breaker.
2. Connect a mono headset to the pilot’s headset output jack and pilot’s mic jack.
NOTE
Use of a true mono headset is required for this test to ensure proper wiring even if a stereo jack is provided
in the installation. Wiring left channel (tip contact) and right channel (ring contact) backwards will cause
failsafe mode not to function with mono headsets. Use of a true mono headset is required for this test (not
a stereo headset with a mono/stereo switch because headset manufacturers differ on how they
accomplish this switching). This will guarantee the condition of the right channel (ring terminal) being
shorted to the return (sleeve terminal) by the mono headset’s plug. This short occurs because of the
physical design of the headset plug contacts and is an inevitable consequence of plugging a mono headset
into a stereo jack. During power-on operation, this short will not damage the audio panel.
3. Verify that COM1 transceiver can be heard in the pilot’s headset.
4. Verify that COM1 can key and transmit the pilot’s mic audio by verifying received sidetone or
checking reception of the transmission with another radio tuned to receive this transmission
(verify Pilot PTT and mic operation is delivered to this transceiver).
5. Apply unit power by restoring the audio circuit breaker to the normal operating position.
8.5.3 Transceiver Operational Check
1. Perform a radio check by exercising the installed transceivers, microphone, microphone key, and
audio over the headset.
2. Verify that communications are loud and clear and PTT operation is correct.
8.5.4 Intercom System (ICS) Check
NOTE
Stereo headsets are recommended if stereo jacks are installed. If a monaural headset is used in a stereo
jack, the audio panel's right channel output is shorted to ground by the mono headset's plug (the audio
panel automatically detects the short and turns off the right channel). In the case of passenger positions
wired in parallel, any stereo listener will lose right channel audio when another passenger plugs in a mono
headset.
1. Set the intercom to the ALL mode [Pilot and Crew LED off]
2. Plug in headsets at each ICS position.
3. Check Pilot and Copilot ICS positions for isolation and proper operation of volume controls.

Page 119
8.5.5 Aircraft Receivers Check
1. Select the audio source corresponding to each installed avionics unit and check for audio over
the headsets.
8.5.6 Bluetooth Music System Check
Use the following steps to Pair and wirelessly connect a Bluetooth equipped phone or tablet to the GMA
245R.
1. On the G3X GDU, select the “Audio Panel” page by selecting “Audio” on the data bar or by
navigating to the Main Menu page, then select the “Audio Panel" button to display the
“Audio/Intercom” page.
2. On the “Audio/Intercom” page scroll to the “Phone & Media” tab.
3. Select “Pair Device” to enable the GMA 245R to be discoverable for two minutes, or until a device
is paired or connected. While discoverable the bar below “Pair Device” will be green and will
change back to a gray bar once paired or a device is not paired within two minutes.
4. While discoverable, a Bluetooth enabled device (e.g., cellphone or tablet) can find and pair with
the GMA. Refer to the device’s instruction manual for information on how to pair and connect to a
new Bluetooth device.
5. Once paired, the appropriate details of the device paired will be displayed.
6. Select the “Music Input” tab and select “Music” (green bar will be displayed under “Music”).
7. Play music from a device using the Bluetooth connection or by controlling on the “Phone &
Media” tab.
8. With the “Music” button selected and the Bluetooth music source selected, verify music is heard
in the connected headsets and that the music volume field adjusts the volume in the headset.
9. Tune the COM Radio to the frequency of a local ground or air traffic control station.
10. From the “Intercom” tab, select “Radio Mutes Music”, and verify music is muted with a
transmission from the tuned frequency.
8.5.7 Speaker Check

1. If a speaker was installed, select SPKR and receive COM audio on the selected COM. When the
speaker is selected, the selected Receivers on the GMA (COM, NAV, AUX ) should be heard
from the speaker.
NOTE
To ensure the music audio is not being muted by ICS or by COM audio, disable radio and
ICS muting. Also, deselect the PILOT or CREW buttons so that there is no ICS Isolation.
8.5.8 Marker Beacon Operation (if installed)
1. Using a ramp tester, simulate the outer marker, middle marker and inner marker signals by
following the test equipment manufacturer’s instructions. Verify that each marker audio signal is
present over the pilot headset and cockpit speaker (if installed).
2. From the pilot headset position, verify that marker audio can be heard when selected.
3. Verify that the outer, middle, and inner annunciations appear on the G3X GDU when the
corresponding signal is applied.
NOTE
Outer Marker – Blue Lamp – 400 Hz (AM or received audio tone)
Middle Marker – Amber Lamp – 1300 Hz (AM or received audio tone)
Inner Marker – White Lamp – 3000 Hz (AM or received audio tone).
NOTE
For instructions to configure Marker RF threshold sensitivity and audio volume settings,

Page 120
see the Installation Manual for the avionics system to which it is integrated for User
Interface control.
4. Verify that during HI SENS operation, the RF threshold is more sensitive (marker audio/indication
occurs as a lower RF power) when in HI SENSE mode.
8.6 ADS-B Traffic Interface Check
NOTE
The following steps may be performed as a ground check as long as the aircraft is within range of an FAA
ground station with available targets of opportunity. If this is not the case, it is recommended that these
checks be performed in flight within range of an FAA ground station.
If the installed system is configured to receive ADS-B In data through an interface with an ADS-B In
capable unit (GNX 375, GTX 3X5 or GDL 50R/52R), the interface is verified as follows:
1. Verify the GDU is in normal mode.
2. Select the Traffic page on the home screen of the MFD or the multi-function pane on the PFD.
3. Turn on the interfacing ADS-B In capable equipment.
a. If the installation includes TAS/TCAS correlated traffic, turn on the TAS/TCAS source.
4. Make sure an amber NO DATA or TRAFFIC FAIL messages are not displayed over or below the
“ownship” icon.
5. Make sure there are no FAIL annunciations in the upper left-hand corner of the traffic status
window. Depending on installation either or should be displayed if ADS-B

Interface is correct.
a. If the installation includes TAS/TCAS correlated traffic, verify that the TAS/TCAS status is
either OPER or STBY.
6. Observe targets of opportunity from ADS-B equipped aircraft, or an FAA ground station.
7. Apply power to any installed L-band equipment such as transponders, DME or TCAS, ensure
there is no interference with ADS-B data reception.
8.6.1 TCAS Traffic Interface Check

1. Verify the GDU is in normal mode.
2. Select the Traffic page on the home screen of the MFD or the multi-function pane on the PFD.
3. Verify that no TAS/TCAS failure annunciations (“NO DATA”, “TRFC FAIL”, “NO TRFC DATA”,
“DATA FAILED”, “FAILED”) are shown on the traffic map.
4. In the upper left corner of the Traffic Map page, verify that the Traffic Status is either TAS/TCAS:
OPER or TAS/TCAS: STBY (“TIS: FAIL” or “TAS/TCAS: FAIL” must not be displayed).
5. Select the Traffic Status button and change the mode between Operate and Standby.
6. Verify that the mode of the traffic system is updated accordingly.
7. Put the traffic system in Standby mode.
8. Initiate a traffic system self-test by selecting the Test button at the bottom of the page. Note: The
Self-Test button will not be selectable if the traffic system is not powered on or is in a failed
status.
9. Verify that the traffic system runs a self-test and the self-test traffic pattern is displayed.
8.7 TIS-A Traffic Interface Check

If a Garmin GTX 3X5(D) transponder is connected to the G3X Touch system and no other traffic systems
covered in this manual is installed, the traffic interface is verified as follows:
1. Verify the PFD is in normal mode. For a dual GDU installation verify both are in normal mode,
and test is performed on the MFD.
2. For single GDU installations, select the Traffic page in split screen format on PFD.
Page 121
3. Turn on the GTX 3X5(D) by pressing ALT on the GTX.
4. Verify that the Traffic Status is not TIS Fail.
5. Verify that the amber NO DATA is not displayed over the “ownship” symbol.
6. Verify that the Traffic Status is in Standby mode. (i.e., TAS should not be displayed).
7. Attempt to place the system in Operate mode, if the aircraft is within TIS-A coverage, the system
will display Operate, if the aircraft is not within TIS-A coverage, the unit will display ‘Unavailable’.
8.8 WX-500 Stormscope Interface Check

1. Verify the GDU is in normal mode. For a dual GDU installation verify both are in normal mode.
2. Allow up to five minutes for the system to obtain a GPS position fix.
3. On the PFD/MFD (GDU that Stormscope is connected to) Map page, select MENU.
4. Touch Lightning Detection button on the screen to activate the lightning system.
5. Verify bar on the lower part of the ‘button’ turns to green. On the Map page, the following symbol
will be displayed on the lower left corner of the map.
6. From the Map page, press the MENU button, and select Set Up Map.
7. Scroll tabs as necessary to the Lightning Tab.
8. On the Lightning tab, ensure ‘On’ is selected under Lightning Detector Data field.
9. Select the Self Test button to determine if there are any faults on the WX-500 system.
10. Select the desired range to be displayed under Lightning Symbol field.
Figure 8-2 – Lightning Tab

11. Select between Cell and Strike modes under Lightning Detector Mode field.
12. Refer to the WX-500 Installation Manual for specific post installation test procedures to simulate
and view strike data on the Map page.
8.9 FIS-B Weather via ADS-B In
NOTE
The following steps may be performed as a ground check as long as the aircraft is within range of an FAA
ground station. If this is not the case, it is recommended that these checks be performed in flight within
range of an FAA ground station.
1. Verify the G3X Touch EFIS is in normal mode.

2. Verify the GPS and FIS-B source is in normal mode.
3. Allow up to five minutes for the system to obtain a GPS position fix.
4. On each installed GDU, select the Weather page. If more than one data sources are installed,
press MENU then select the FIS-B under the “Data Source” field, otherwise, the data source
selection will be automatic.

Page 122
NOTE
It may take up to 10 minutes after power-on for the system to begin receiving FIS-B weather products.
5. Verify there are no warnings displayed.

6. Push the GDU knob (right knob on GDU 460), then select several FIS-B weather products to
display.
7. Verify at least one of the selected products displays a valid time stamp.
8. Verify there are no status fail messages regarding FIS-B weather.
8.10 GDL 51R/52R SXM Weather Check

SiriusXM weather and radio activation is required for this check, reference Section 7.14 for instructions.
Position the aircraft where there is a clear view of the southeastern or southwestern sky. XM Satellite
Radio satellites are located above the equator over the eastern and western coasts of the continental
United States.
1. Verify the G3X Touch system is in normal mode.
2. Allow up to five minutes for the system to obtain a GPS position fix and the GDL 5XR to obtain
data.
3. On each GDU, select the Weather page from the multi-function pane.
4. Verify there are no warnings displayed.
5. Push the GDU knob (right knob on GDU 460) to display weather data page.
6. Verify weather data associated with the subscribed service level is available. Examples of
weather data available are “NEXRAD, METAR, Winds Aloft, Lightning etc.
8.11 GDL 51R/52R SXM Audio Interface Check

This procedure only verifies correct installation and activation of G3X Touch system functions. It does not
activate the GDL 5XR Series XM data link radio. SiriusXM weather and radio activation is required for this
check, reference Section 7.14 for instructions.
1. Position the aircraft where there is a clear view of the southeastern or southwestern sky. (XM
Satellite Radio satellites are located above the equator over the eastern and western coasts of
the continental United States.)
3. Allow up to five minutes for the system to obtain a GPS position fix and the GDL 5XR to obtain
data.
4. On each GDU’s Multi-function pane, select the SXM page.
5. Verify Audio signal bars are in the Green and that the displayed subscription level is accurate.
6. Verify that under Artist “XM DATA LINK FAIL” is not displayed.
7. Using the inner knob, scroll the channels.
8. Verify that music plays on multiple channels.
8.12 EIS Check

This section contains procedures to verify proper installation, operation, and gauge markings of the EIS.
Complete the following applicable checkouts if EIS sensor or gauge settings may have been affected by
maintenance.
CAUTION
Check hose routing for sharp bends. Check sensors and fittings for leaks during and after engine run-up
and correct prior to flight.

Page 123
8.12.1 EIS Annunciator Light Check (If installed)
If EIS annunciator lights are installed on a G3X Touch system with a standalone MFD, perform the
procedures below in configuration mode to verify proper operation of the annunciator discrete outputs
from the GEA:
1. Apply power to the aircraft.
2. Press and hold down the MENU key while powering on the GDU 4X0, until the Configuration
Mode page appears.
3. Select the “Systems Information” page.
4. On the “Device List” tab, navigate to the EIS field.
5. On the “Engine Information System Info” tab, select the “Annunciator Test” button while observing
the EIS annunciator lights.
• Verify the lights illuminate.
NOTE
If the annunciator lights do not illuminate, verify lamp operation (Section 8.12.4). If lamp check is good,
remove power from the aircraft and inspect wiring.
8.12.2 EIS Ground Check

Conducted with the engine off and at ambient temperature.
1. Verify the G3X Touch system in normal mode.
2. Navigate to the engine page on the MFD or multi-function pane of the PFD in split format.
3. Verify that no red or amber X marks are present on any EIS gauge.
4. EGT/CHT- Apply heat to each EGT/CHT sensor to verify the corresponding cylinder is connected
correctly.
NOTE
If the temperature decreases when heat is applied, the wire polarity may be reversed.
5. Oil and fuel pressure(s)- Verify the corresponding gauge(s) read 0 +/-1 PSI.
6. Manifold Pressure - With engine not running, verify that the Manifold Pressure Gauge reads
ambient pressure +/-1 inHg. To determine ambient pressure at your location, multiply the current
altimeter setting by the Field Elevation (FE) Factor below. For example, if the altimeter setting is
30.10 and the field elevation is 1700 ft, the FE Factor is 0.9400 (30.10 x 0.9400 = 28.29 local
ambient pressure). If out of tolerance, calibrate the Manifold Pressure using the on-screen
instructions.
Field Elev. FE Factor Field Elev. FE Factor Field Elev. FE Factor
-500 1.0182 2000 0.9298 4500 0.8477
-400 1.0145 2100 0.9264 4600 0.8445
-300 1.0109 2200 0.9230 4700 0.8414
-200 1.0073 2300 0.9196 4800 0.8382
-100 1.0036 2400 0.9162 4900 0.8351
0 1.0000 2500 0.9129 5000 0.8320
100 0.9964 2600 0.9095 5100 0.8289
200 0.9928 2700 0.9062 5200 0.8258
300 0.9892 2800 0.9028 5300 0.8227

Page 124
Field Elev. FE Factor Field Elev. FE Factor Field Elev. FE Factor
400 0.9856 2900 0.8995 5400 0.8196
500 0.9821 3000 0.8962 5500 0.8165
600 0.9785 3100 0.8929 5600 0.8135
700 0.9750 3200 0.8896 5700 0.8104
800 0.9714 3300 0.8863 5800 0.8074
900 0.9679 3400 0.8830 5900 0.8043
1000 0.9644 3500 0.8798 6000 0.8013
1100 0.9609 3600 0.8765 6100 0.7983
1200 0.9574 3700 0.8733 6200 0.7953
1300 0.9539 3800 0.8700 6300 0.7923
1400 0.9504 3900 0.8668 6400 0.7893
1500 0.9469 4000 0.8636 6500 0.7863
1600 0.9435 4100 0.8604 6600 0.7833
1700 0.9400 4200 0.8572 6700 0.7804
1800 0.9366 4300 0.8540
1900 0.9332 4400 0.8508
7. Current or Voltage- Verify the corresponding gauge(s) display the correct measurement(s).
8. Fuel Quantity- Verify the indicated fuel quantities are accurate for each tank when the aircraft is
leveled in accordance with the aircraft manufacturers instructions.
NOTE
The GEA 24 interface to resistive fuel probes must use a pair of 2.2kΩ resistors and be
configured as ‘Voltage’ interfaces (refer to Garmin SB 2134 and Installation Manual Rev.9 or
later). If a GEA 24 is replaced by a GEA 24B, any fuel quantity interfaces to resistive probes
must be recalibrated regardless of whether the 2.2kΩ resistors in the harness are retained or
removed. For new installations with a GEA 24B, the resistors are not required, reference the
STC Installation Manual Rev 14 (or later).
8.12.3 EIS Engine Run-Up Check

Always follow engine startup procedures as described in the Aircraft POH.
CAUTION
If the engine indications are not within operating specifications shortly after starting, IMMEDIATELY shut
down the engine and troubleshoot the problem. Failure to do so may cause engine damage.
Obtain an optical tachometer to monitor propeller RPM.

1. Place the aircraft in an open and clear area appropriate for an extended engine run-up.
2. Follow the engine start-up procedure as outlined in the aircraft POH. Adhere to the required
observations immediately following the start such as oil pressure within 30 seconds.
3. Verify the EIS RPM gauge(s) match the optical tachometer reading +/- 50 RPM.

Page 125
4. Allow the engine to warm up and oil temperature to increase to at least 100°F.
5. Verify the alternator load meter (if installed) and battery charge/discharge ammeter (if installed)
indicate a positive load.
6. Perform individual magneto checks as specified by the aircraft POH. If the RPM does not drop as
expected when switching from both magnetos to one, the P-lead, ignition switch wiring, or
magneto timing is incorrect. Discontinue the test immediately and repair the ignition system.
7. Verify all EIS readings are consistent with normal operation performance in accordance with
aircraft type design, engine type design, and/or aircraft POH/AFM.
8. Verify the accuracy of the fuel flow indication.
9. Verify all installed sensors and fittings are free of leaks.
8.12.4 EIS Annunciator Lamp Check (If installed)

Perform a check of the EIS annunciator lamps as follows:
2. Ensure the lens is not dimmed by rotating the lens holder counter clockwise.
3. Momentarily press the lens with light pressure, and verify light is illuminated.
• If light does not illuminate, replace the lamp. Reference Section 6.14.1 for lamp replacement
instructions.
8.13 ADAHRS and Magnetometer Ground Checks

This section contains the ground checks that may be performed on the magnetometer for ADAHRS
aspects of the G3X system.
CAUTION
To avoid damaging the ADAHRS pressure sensors, the pitot and static ports and GAP 26 (if installed)
must be connected to the test set. Note that the GAP 26 has drain holes on the underside of the probe
which must be covered during the test.
8.13.1 Altimeter Check

The GDU 4X0 altitude displays must be verified per Title 14 CFR 91.411 and 14 CFR Part 43 Appendix
E, with the following exception to 14 CFR Part 43 Appendix E, paragraph (b)(1):
• The tests of sub-paragraphs (iv) (Friction) and (vi) (Barometric Scale Error) are not applicable
because the digital outputs of the GSU 25D are not susceptible to these types of errors.
This procedure is recommended when the GSU 25D is removed and reinstalled/replaced or the pitot and
static system connections are disturbed.
8.13.2 Pitot-Static and Airspeed Tape Settings Checks

The following section verifies the correct operation of the GDU 4X0 altitude and airspeed display
functions. These tests require the use of a Calibrated Air data test set. When using a Calibrated Air data
test set, only simulate normal aircraft operating conditions, as defined in the aircraft Type Data
(POH/AFM) or other approved STC to avoid component damage.
Airspeeds above Vne should not be checked.
The aircraft or instrument manufacturer’s data should be referenced for tolerances for this test where
available.
1. Connect the calibrated air data test set to the aircraft.
3. Verify all self-tests pass on the main startup screen.
4. Using the air data test set, increase the airspeed until the PFD airspeed tape pointer is at the
bottom of the white band (Vs0).

Page 126
5. Verify that the pitot and static pressure settings used on the test set match what is displayed on
the GDU.
6. On the pitot static test set, change the airspeed until the PFD airspeed tape pointer is at the
bottom of the green band (Vs1).
7. Verify that the bottom of the green arc/band on the standby ASI and PFD airspeed tape are at the
same airspeed value.
8. Change the airspeed until the PFD airspeed tape pointer is at the top of the white band (Vfe).
9. Verify that the top of the white arc/band on the standby ASI and PFD airspeed tape are at the
10. Change the airspeed until the PFD airspeed tape pointer is at the top of the green band/bottom of
the yellow band (Vno).
11. Verify that the top of the green arc/band on the standby ASI and PFD airspeed tape are at the
12. Increase the airspeed to the upper red radial/top of yellow arc (Vne).
13. Verify that the red radial on the standby ASI and PFD airspeed tape are at the same airspeed
value.
14. Starting at the current airspeed, decrease the airspeed to zero, stopping at each of the airspeeds
listed in Table 8-2. verifying that the PFD and standby ASI airspeed values are within the
tolerances indicated in Table 8-2.
NOTE
The aircraft or instrument manufacturer’s data should be referenced for standby tolerances, if
available.
Table 8-2 – Airspeed Test Points
Test Set Allowed Tolerance Recorded Result Recorded Result for

(KTS) (+/- KTS) GDU installed Standby ASI)
50 5.0
80 3.5
100 2.0
120 2.0
150 2.0
8.13.3 Compass Swing

After the Magnetometer Calibration Procedure is completed, a compass swing must be performed to
verify the ADAHRS/GMU 11 heading accuracy.
1. Verify ‘Auto Mag. Variation’ is selected.
o With the PFD in Normal mode, navigate to the Position Setup Page (Menu → Main Menu
→ Setup →Position).
o Under Heading tab, ensure ‘Auto Mag. Variation’ is selected.
o Return to the main screen.
2. With the PFD in normal mode, all of the aircraft and avionics systems powered and operating
normally, position the aircraft on a known compass rose at a heading 360° (North), or select a
level and magnetically clean location and use a sight compass to position the aircraft to a heading
of 360° (North)

Page 127
3. Record the HDG value displayed on the PFD as indicated in Table 8-3, below. Also record the
heading displayed on the standby compass. Verify or correct the standby compass deviation
card.
4. Repeat step 2 for each of the headings listed in Table 8-3.
5. Calculate the heading errors by subtracting the displayed (B) value from the actual (A) value for
each of the headings in Table 8-3.
6. If all calculated heading errors displayed on the PFD are at or within +/-10° from the surveyed
heading, the installation is acceptable, and no further work is required to correct the GMU 11
installation.
7. If a Heading Error (A-B) is greater than +/- 10°, calculate the average error by adding all errors
and dividing by 12. This is the angle by which the GMU 11 must be physically rotated to correct
the installation.
8. Modify the installation to rotate the GMU 11 by the amount calculated in the previous step. When
looking down at the GMU 11, rotate clockwise for positive values, and counterclockwise for
negative values.
9. After physically correcting the GMU 11 installation, repeat the procedures in Section 7.2.1.2 and
8.13.3.
Table 8-3 – Heading Verification – ADAHRS Check
Heading (A) Displayed ADAHRS Heading Error (A-B) Standby Compass
Heading (B) Heading
360° (North)
30°
60°
90°(East)
120°
150°
180°(South)
210°
240°
270°(West)
300°
330°
8.14 GTR 20/200B Ground Checks
NOTE
To enter configuration mode on the GTR 200B, remove power from the unit and with unit
powered off, press and hold the SMALL knob and apply power by turning the PWR VOL knob
clockwise. Release the SMALL knob when the display activates, and config mode is
displayed.
8.14.1 Headset Tests Page (Configuration Mode) (GTR 200B Only)
The Headset Tests page allows the installer to test the operation of the headset outputs:
1. Enter configuration mode on the GTR 200B, from the Configuration Mode Home page, turn the
LARGE Knob to highlight the Headset Tests page and press the SMALL Knob to display.
Stereo headsets with the stereo setting selected must be used with 3D audio. Stereo headsets are
shipped set to mono. Make sure the headsets used for this test are set to the stereo position.

Page 128
A true mono headset will work correctly with the GTR 200B, but only mono audio will be heard, and 3D
audio will not be available. The GTR 200B will detect the mono headset and automatically switch to mono
operation. A mono headset plug can be identified by the absence of the RING. Perform the below
procedure to verify proper headset configuration.
2. Connect a stereo headset to the pilot headset position.
3. Move to the HEADSET TEST subpage.
4. Verify that none of the HS SHORT checkboxes are checked.
- If the HS SHORT L checkbox is checked it is likely that there is an installation wiring problem.
- If the HS SHORT R checkbox is checked it is likely that a mono headset is plugged in or
there is an installation wiring problem.
- If both the HS SHORT L and R checkboxes are checked it is likely that a stereo headset set
to mono is plugged in.
- If any of the HS SHORT checkboxes are checked, and no headset is plugged in, check for an
installation wiring problem.
5. Use the SMALL Knob to move through the TEST TONE positions. The positions are:
- PIL LEFT – A tone should be heard in the left ear speaker of the pilot headset.
- PIL RIGHT – A tone should be heard in the right ear speaker of the pilot headset.
- COP LEFT – A tone should be heard in the left ear speaker of the copilot headset.
- COP RIGHT – A tone should be heard in the right ear speaker of the copilot headset.
6. Verify that the test tone is heard in the correct headset ear speaker and the tone is not heard in
any other position.
7. Repeat steps 2 through 6 for the copilot headset position.
8.14.2 COM Tests Page (Configuration Mode) (GTR 200B Only)
The COM Tests page allows the installer to test the operation of the COM functions.
Perform the below procedure to verify proper COM configuration:
1. Enter configuration mode on the GTR 200B, from the Configuration Mode Home page, turn the
LARGE Knob to highlight the COM Tests page and press the SMALL Knob to select the COM
TESTS subpage.
2. Connect a headset to the pilot headset jacks.
3. Verify the following checkboxes are not checked:
- TX – Indicates the radio is transmitting.
- RX – Indicates the radio is receiving.
- SQ – Indicates the radio squelch is overridden. Radio squelch can be overridden by pushing
the volume knob.
- LO VOLT - Indicates the radio input voltage is low. The radio will reduce TX power or stop
transmitting completely depending on the voltage level.
- HI TEMP – Indicates the transmitter temperature is high. If transmitter temperature is high the
radio will reduce TX power until the temperature lowers.
- TX AMPS – This is not a checkbox. This indicates how much current (in Amps) is supplied to
the transmitter. When the GTR 200B is transmitting the current draw will be approximately
3.0 Amps under ideal load conditions. When the GTR 200B is not transmitting the current
draw will be around 0.01 Amps.
4. If the LO VOLT checkbox is checked this indicates a low battery condition or wiring fault that is
preventing the radio from receiving proper voltage. Correct this condition before proceeding with
this test.
5. Select a frequency that is transmitting. An ATIS, ASOS, or other continuously transmitting
frequency is a good choice. Frequency tuning works differently in configuration mode. The
SMALL Knob changes the highlighted frequency field and the LARGE Knob moves the
highlighted field.

Page 129
6. Verify the RX checkbox is checked, and the received audio can be heard in the headset.
7. Select a frequency that is safe for transmission. The antenna and coaxial cable must be properly
connected to the radio before attempting to transmit.
8. Key the transmitter and verify the TX checkbox is checked while transmitting. If the checkbox
does not check, there is a wiring fault. If the checkbox is always checked there is a wiring fault.
9. If the radio is tuned to a frequency that is appropriate for a radio check, one can be performed as
part of this test.
10. If the copilot position is wired for transmission repeat steps 2 through 9 for the copilot position.
8.14.3 Receiver/Transmitter Check (Normal Mode)
Tune the unit to a local VHF frequency and verify the receiver output produces a clear and
understandable audio output. Verify the transmitter functions properly by contacting another station and
getting a report of reliable communications.
8.14.4 Alert Volume Check
This check is performed with GDU in configuration mode to verify proper alert volumes for alert, message,
AOA, and Alt Alert as applicable.
1. Apply power to aircraft with GDUs in configuration mode.
2. Connect a headset to the pilot’s headset output jack and pilot’s mic jack.
3. Navigate to the “Sound Configuration” page.
4. Select the Test button
• Verify proper sound volume is heard on the headsets.
5. Repeat step 4 for all applicable alerts.
8.15 Garmin GFC 500 Autopilot

For aircraft equipped with Garmin GFC 500 autopilot system, perform interface checkout of the autopilot
in accordance with procedures outlined in GFC 500 Part 23 AML STC Installation Manual 190-02291-00.
8.16 Non-Garmin Autopilot Interface

Before proceeding with the autopilot interface tests, verify the G3X system and non-Garmin autopilot
have been properly configured. For configuration instructions reference Appendix B.5. and the G3X
Touch EFIS Part 23 AML STC Installation Manual (190-02472-01). Only those interfaces which are
directly affected by the G3X Touch STC are covered by this manual; if any other autopilot modifications
were performed, they are outside the scope of this STC and must be checked in accordance with the
autopilot installation manual.
WARNING
It is important that the PFD be properly configured in order to prevent damage to the autopilot computer.
NOTE
The following procedures are general in nature and it may be necessary to reference the autopilot
manufacturers testing instructions to allow the autopilot to be tested properly.
A calibrated VHF NAV test set is required for some tests in this section.
8.16.1 Autopilot Engagement Check

This section verifies that the autopilot can be engaged.
1. Verify the G3X Touch system is in normal mode. Allow the PFD to obtain a valid heading,
attitude, altitude, and GPS location.
2. Verify the GPS navigator is in normal mode.

Page 130
3. Engage the autopilot. If the autopilot cannot be engaged, troubleshoot using the instructions in
the autopilot installation manual.
4. If step 3 was successful, disengage the autopilot.
8.16.2 Heading and Course Error Check
This section verifies that the heading and course error interface between the GDU 4X0 and autopilot
computer is functional. For dual GDU G3X Touch installations, the following instructions apply only to the
PFD.
8.16.2.1 Heading Error
2. On the PFD set the heading bug to the current aircraft heading.
3. On the PFD, verify HDG/CRS Valid.
4. Engage the autopilot in HDG mode.
5. Adjust the heading bug to the right.
6. Verify that the control yoke or stick moves to the right.
7. Adjust the heading bug to the left.
8. Verify that the control yoke or stick moves to the left.
9. Adjust the heading bug to the aircraft heading.
10. Disengage the autopilot.
NOTE
If the control yoke or stick moves in the opposite direction of what is expected, reverse the
LEFT/RIGHT HDG Polarity on the Autopilot Calibration page and continue the checkout
process.
8.16.2.2 VOR Course Error
Some autopilot systems might not have course error capability; and this step is not necessary for those
systems.
1. Apply power to the aircraft and aircraft systems and allow the aircraft systems to initialize.
2. Tune the VHF NAV to the NAV/COM Test Set frequency for VOR operation.
3. Set the Course pointer on the PFD HSI 15 degrees to the left of aircraft heading and ensure that
the PFD CDI is displaying VOR navigation information.
4. Simulate a VOR signal with a “TO” course equal to the aircraft heading.
5. Slowly adjust the course pointer on the PFD CDI toward the aircraft heading until VOR captures.
6. Center PFD CDI course pointer on the aircraft heading.
7. Engage the autopilot in NAV mode.
8. Adjust the NAV ramp tester course and the PFD CDI course pointer 20 degrees to the left of
current aircraft heading.
9. Verify that the flight controls move toward the left.
10. Adjust NAV ramp tester course to aircraft heading.
11. Adjust the NAV ramp tester course and the PFD HSI CDI course pointer 20 degrees to the right
of current aircraft heading.
12. Verify that the flight controls move toward the right.
13. Adjust the NAV ramp tester course to aircraft heading.
8.16.2.3 Localizer
1. Tune the VHF NAV to the NAV/COM Test Set frequency for LOC operation.
2. On the NAV ramp tester simulate centered LOC needle presentation.
3. Set the Course pointer on the PFD HSI to the current aircraft heading.
4. Verify the PFD CDI displays centered deviation for LOC.
5. On the NAV ramp tester simulate 0.093 DDM Left LOC.

Page 131
6. Verify PFD CDI deviation bar is one dot left.
7. Verify that the flight controls turn to the left.
8. On the NAV ramp tester simulate 0.093 DDM Right LOC.
9. Verify PFD CDI displays one dot right.
10. Verify that the flight controls turn to the right.
11. On the NAV ramp tester simulate centered LOC needle presentation.
8.16.3 GPSS Course
This test is only performed for installations that are interfaced to a GPS navigation source and the
interfaced autopilot did not previously have a GPSS function. Conduct this test with the aircraft
positioned where it can receive GPS signal.
1. On the GPS navigator, enter a simple Direct-To flight plan with a waypoint that is on the current
aircraft heading and select the PFD CDI to display GPS. If the navigator has the capability to
enter user waypoints, a user waypoint can be entered to facilitate this test. It is suggested that
the waypoint be within 5 miles of the current aircraft position for best results.
2. On the PFD, press the MENU button to display the 'PFD Options’ page, and select GPSS. A
green bar is displayed at the bottom of the GPSS box to indicate it is selected(enabled).
3. Verify the following:
On the PFD Attitude field
• GPSS field is displayed to the right of the airspeed tape.
On the PFD CDI
• The heading bug is a hollow cyan bug on the CDI.
4. On the navigator select OBS to enter GPS OBS mode.
5. Set the OBS course for the current aircraft heading (it is assumed the waypoint is on the current
aircraft heading).
6. Engage the autopilot in HDG mode.
7. Adjust the OBS course 20 degrees to the left of current aircraft heading.
8. Verify that the flight controls move toward the left.
9. Adjust the OBS course 20 degrees to the right of current aircraft heading.
10. Verify that the flight controls move toward the right.
11. Adjust the OBS course to aircraft heading.

Page 132
8.17 G5 Miscompare Check
This test is only performed on installations with G5 ADI as a standby instrument.
1. Apply power to the aircraft and G3X system and allow G5 to initialize.
2. Verify heading, altitude and IAS values on the G3X PFD match the values on the G5, and
heading, altitude and IAS miscompare messages are not displayed on the PFD.
3. Rotate G3X PFD knob that has been configured for controlling heading and verify “HDG xxxº” is
displayed on the G5 and matches the value on the G3X PFD, and the heading bugs move at the
same rate on both the G5 and G3X PFD.
4. Press the G5 knob then rotate to highlight “Heading” field, press the knob to make selection and
rotate to adjust:
• Verify the values on the heading field on the G3X PFD incrementally change at the same
rate and values match the G5 ADI.
• Verify the heading bugs move at the same rate on both the G5 and G3X PFD
5. Rotate G3X PFD knob that has been configured for controlling the altitude bug and verify the
bugs move, values match and incrementally change at the same rate on both the G5 and G3X
PFD altitude tape.
6. Press the G5 knob then rotate to highlight “Altitude”, press the knob to make selection and rotate
to adjust:
• Verify the altitude bugs move, values match and incrementally change at the same rate
on both the G5 ADI and G3X PFD altitude tape.
7. Rotate G3X PFD knob that has been configured for controlling “Baro” and verify the barometric
pressure and pressure altitude values incrementally change at the same rate and values match
on both the G5 ADI and G3X PFD.
• Verify the “Baro” field on the G5 changes to a cyan color and the digits change to black
color but revert to black field with cyan digits, once the knob is no longer rotated.
8. Rotate G5 ADI knob and verify the barometric pressure and pressure altitude values
incrementally change at the same rate and values match on both the G5 ADI and G3X PFD.
• Verify the “Baro” field on the G3X PFD changes to a cyan color and the digits change to
black color but revert to light background with cyan digits, once the knob is no longer
rotated.
8.18 GI 275 Miscompare Check

This test is only performed on installations with GI 275 ADI as a standby instrument.
1. Apply power to the aircraft and G3X system and allow GI 275 to initialize.
2. Verify heading, altitude and IAS values on the G3X PFD match the values on the GI 275, and
heading, altitude and IAS miscompare messages are not displayed on the PFD.
3. Rotate G3X PFD knob that has been configured for controlling heading and verify “HDG xxxº” is
displayed on the GI 275 and matches the value on the G3X PFD, and the heading bugs move at
the same rate on both the GI 275 and G3X PFD.
4. On the GI 275, tap the selected heading display box (lower left corner below the airspeed tape).
Rotate the knob to adjust the selected heading:
• Verify the values on the heading field on the G3X PFD incrementally change at the same
rate and values match the GI 275.
• Verify the heading bugs move at the same rate on both the GI 275 and G3X PFD.
5. Rotate G3X PFD knob that has been configured for controlling the altitude bug and verify when
the bugs move, values match and incrementally change at the same rate on both the GI 275 and
G3X PFD altitude tape.
6. Rotate G3X PFD knob that has been configured for controlling “Baro” and verify the barometric
pressure and pressure altitude values incrementally change at the same rate and values match
on both the GI 275 and G3X PFD.

Page 133
• Verify the “Baro” field on the GI 275 changes to a cyan color and the digits change to
black color but revert to black field with cyan digits, once the knob is no longer rotated.
7. Rotate GI 275 knob and verify the barometric pressure and pressure altitude values incrementally
change at the same rate and values match on both the GI 275 and G3X PFD.
• Verify the “Baro” field on the G3X PFD changes to a cyan color and the digits change to
black color but revert to black field with cyan digits, once the knob is no longer rotated.
8.19 GAP 26 AOA Probe Checks

The following inspection points should be checked after the re-installation of the GAP 26 is complete:
8.19.1 AOA Probe Heater Check

WARNING
When checking the operation of the GAP 26 heater, do not touch the probe.
1. Verify the proper operation of the AOA probe heater.
• Apply power to the aircraft
• Move the AOA heater switch to the ON position.
• Check the temperature of the probe heater by placing hand above the probe to feel radiant
heat or use a temperature probe to verify the elevated temperature of the probe.
• Move the AOA heater switch to the OFF position.
• Remove power from the aircraft.
8.19.2 AOA Probe Leak Check
NOTE
Although 14 CFR Part 91 does not require a leak test, the AOA system leak test is a
requirement for this STC.
Leak testing must be performed to provide assurance that any leakage is within an acceptable range and
that the system does not experience inconsistent performance or AOA calibration issues. Perform the
AOA system leak test by following the steps below:
• Inspect pitot pressure port, AOA pressure port, and drain holes to ensure that all are undamaged
and clear of debris.
• Ensure all mounting points for the GAP 26 and replacement inspection panel are secure and
there are no visible signs of damage such as cracks around or extending from mounting holes.
• To prevent burns to the body or damage to test equipment disable the heater functionality by
opening the circuit breaker prior to performing the leak test.
• If a pitot-static tester is used to perform this test, the required airspeed input is 150 knots.
• Perform the leak test on the pneumatic system with the probe installed on aircraft and with the
drain holes fully sealed.
• Apply 150 knots pressure to the system and measure the pressure loss over one minute. A leak
rate of 10 knots/min or less is allowable and still maintains proper functionality.
NOTE
Both pressure chambers on the GAP 26 probe have drain holes that when open during normal operation
would constitute a designed-in leak that is several times higher than 250 knots/min but does not add
significant error.
• After the leak test is completed, make sure all pressure ports and drain holes on the GAP 26 are
open and clear of debris.
WARNING
Failure to make sure the pressure ports and drain holes on the GAP 26 are open and clear of debris
could result in equipment damage or a decrease in safety margins.

Page 134
8.20 Wig-Wag Landing/Taxi Light Check (if configured)
2. Locate the Landing and Taxi Light switches and turn both to Flash.
• Verify the landing and taxi light alternately flash.
3. Turn both “Switch (On)” switches to on and verify they are on continuously.
4. Remove power from the aircraft
8.21 CO Detector Display Check (if configured)

1. Apply power to the aircraft with the GDUs in normal mode.
2. On the GDU, navigate to the “Main Menu”,
3. Select “Setup”
4. Select “Data Bar”, on “Data Fields” select “Change”.
5. Touch the magenta pilot-configurable data bar field and select “Carbon Monoxide (ppm)” on the
“Data Bar Setup” page to display CO level on the data bar.
• Verify a CO readout on the data bar field is between 0 to 9 PPM.
6. Remove power from the aircraft
8.22 Weight and Balance (W&B) Update (as required)
CAUTION
It is the installer’s responsibility to verify the accuracy of the data/values entered and the
resulting envelope graph depicted on the weight and balance configuration page.
NOTE
The Pilot Operation Handbook (POH) for the aircraft being configured is required to configure
the weight and balance page.
NOTE
Refer to the G3X Touch Installation Manual for information on configuring the Weight &
Balance Page.
The following procedure must be performed when a weight and balance change is made to the aircraft.
This ensures the accuracy of the weight and balance page on the G3X system.
1. Apply power to the aircraft with the GDUs in normal mode.
2. On the GDU, Press the MENU Key twice to display the Main Menu.
3. Touch the Weight & Balance Button. The Weight & Balance Page is displayed.
4. From the Weight & Balance page, press the MENU Key.
5. Touch the Empty Aircraft Button.
6. On the ‘Empty All Stations?’ pop-up screen, touch the Yes Button to empty the aircraft Weight &
Balance page data.
7. On the Weight & Balance page, verify the Weight and CG value match with those listed in the
aircraft manufacturer Pilot Operation Handbook (POH) and the associated aircraft weight and
balance sheet.
An ‘Out Of Range’ red message may be displayed due to all aircraft Stations being cleared on
previous steps.
8. If the Weight and CG value listed on step 7 are different than those on the aircraft manufacturer
Pilot Operation Handbook (POH) and the associated aircraft weight and balance sheet, follow the
applicable procedure on the G3X Touch Installation Manual to update the weight and balance
information.

Page 135
8.23 EMI / RFI Check
An EMC check must be conducted once the G3X Touch system is installed and all interfaces to external
equipment are verified to be working correctly. The EMC check verifies that the G3X system is not
producing unacceptable interference in other avionics systems and other avionics systems are not
producing unacceptable interference in the G3X system. Table 8-4 below should be used to collect data
for this check.
1. Enter equipment installed in the aircraft into the Source row and Victim column of the form.
2. Apply power to all avionics systems except for the components that are part of the G3X system.
3. Verify all existing avionics systems are functioning properly.
4. Apply power to the G3X system.
5. Remove power from all other avionics systems.
NOTE
Wait for the current system start up sequence to finish before applying power to the next system.
6. Apply power and/or operate the systems listed on the fillable form on Table 8-4, one system at a
time. Make sure to pull/push circuit breakers or turn on/off large loads, e.g. heaters, cycling flaps
(if electrical) etc.
7. Verify the G3X system functions properly and no related messages are displayed.
8. Verify each radio is functioning properly by completing the following:
a. For each VHF COM radio, monitor one local frequency, one remote frequency, and one
unused frequency.
b. Verify no unintended squelch breaks or audio tones interfere with communications.
c. For each VHF NAV radio, monitor one local frequency, one remote frequency, and one
unused frequency.
d. Verify there are no guidance errors.
e. Verify no audio tones interfere with the station ID.
f. For each GPS Navigator, enter a simple flight plan and display as appropriate. i.e.
Navigator Display, PFD, CDI etc., if installed.
g. Verify there are no guidance errors.
9. If an EI FT-60 or an EI FT-90 fuel flow sensor is installed, verify the fuel flow indication is accurate
and the indication does not fluctuate or invalidate the display.
a. Transmit various modulating tones on each COM radio (e.g. Whistling).
b. See section the G3X Touch EFIS Part 23 AML STC Installation Manual (190-02472-01)
for details if the fuel flow indication fluctuates.
NOTE
EMI check of the fuel flow must be performed with the engine running.
10. Verify all other avionic systems are functioning properly.

Page 136
Table 8-4 – EMI Victim/Source Matrix
Communication Radio(s)
GTP 59 (OAT indication)
GMU 11 (Mag. Heading)
GEA24(B) (if installed)

GSU 25D (PIT/ROLL)
GDL 5XR (if installed)
Gov RPM Incr / Decr

GDU #2 (If installed)
Navigation Radio(s)
GAD 27 Light Flash

Magnetic compass
Hydraulic System
GAD 29B/29D (If
Radar Altimeter
Anti-Collision Lt
GAP 26 Heater
Autopilot / SAS
Landing Lights
Transponder
Audio Panel
Pulse Light
TAS/TCAS
Fuel Valve
Generator
Pitot Heat
installed)
GDU #1
Pos Lt
GDU #1
GDU #2
(If installed)
GMU 11
(Mag. heading)
GAD 29B/29D
(If installed)
GSU 25D
(PIT/ROLL)
GDL 5XR (if
installed)
GEA 24(B) (if
installed)
GTP 59 (OAT
Indication)
Magnetic
Compass
Navigation
Radio(s)
SOURCE
Communication
Radio(s)
Fuel Valve
Pitot Heat
Pulse Light
Generator
Pos Lt
Anti-Collision Lt
Landing Lights
Gov RPM Incr /
Decr
Hyd System
Radar Altimeter
TAS/TCAS
Transponder
Audio Panel
Autopilot / SAS
GAP 26 Heater
GAD 27 Light
Flash

Page 137
APPENDIX A INSTALLATION SPECIFIC INFORMATION
A copy of this appendix must be used to record information for a specific installation of the G3X Touch
EFIS Part 23 AML STC system. The completed copy must be kept with the aircraft permanent records.
This appendix includes the following information:
A.1 Maintenance Records
This Post-Installation Configuration Log should be completed during the initial installation, with any
software modifications post initial installation, and maintained with the aircraft permanent records.
• G3X software version used to perform software updates.
• Record part and serial numbers of all LRU’s at installation.
• Record Mod Status of all LRU’s at installation.
• Record part and serial numbers of any LRU which was replaced.
• Record any database updates which were performed during maintenance.
• Any other applicable information related to the maintenance work performed on the aircraft.
• Capture configuration data and save on an SD card (Refer to Appendix A.4).

Page A-1
Table A-1 – G3X Post-Installation Log
Post-Installation Configuration Log

Date: Aircraft Model: Aircraft Make:
Aircraft
Aircraft Serial #: Engine:
Registration #:
New Software Version (if

Original Software Version:
applicable):
Installed/Enabled?
LRU Serial
Unit/Option (check if installed or LRU Part Number Mod Status
Number
configured)
GDU 460
GDU 470
GMU 11
GSU 25D
GTP 59
GAD 29B/29D
GAD 27
GEA 24(B)
GDL 5XR
GTR 20
GTR 200B
GMA 245R
GAP 26

Page A-2
A.2 Equipment Locations
Appendix B contains a documentation sheet for recording G3X Touch EFIS LRU’s included in the
installation and its location on the aircraft. The document will be completed during the initial installation
and maintained with the aircraft records.
Table A-2 – G3X Equipment Locations
Date: Aircraft Make/Model: Aircraft Reg #/Serial #:
LRU Station C.G Description of Location

GDU 460 in.
GDU 470 in.
GMU 11 in.
GSU 25D in.
GTP 59 in.
GAD 29B/29D in.
GAD 27 in.
GEA 24(B) in.
GDL 5XR in.
GTR 20 in.
GTR 200B in.
GMA 245R in.
GAP 26 in.
A.3 Wire Routing

Figure A-1 is a generic aircraft drawing to be used for documenting the wire routing for the installation of
the G3X Touch EFIS LRUs. The drawing will be completed during the initial installation and maintained
with the aircraft records.
Record equipment locations and sketch the approximate location of wire routing, pneumatic line routing,
and location of pneumatic drain (if installed) on Figure A-1 below as applicable.

Page A-3
Figure A-1– Generic Aircraft Figure

Page A-4
A.4 Configuration File
The “Config File” page is used to enable uploading and downloading of the G3X System configuration to
an SD card. The configuration is written to the loader card in a format which can be uploaded to the
system.
NOTE
An SD card must be in the display’s SD card slot for the “Config Files” page to be shown on
the Configuration Mode page.
To export the configuration:

1. In configuration mode, navigate to the “Config Files” Page.
2. Press the MENU button.
3. Use the Touch Panel or a Move Selector Knob to select Export System Configuration
4. Message below will appear on the screen, select “Yes” when prompted.
5. The data will be saved on the SD card as a “config.gcb” file in a “config” folder within a “Garmin”
folder.
NOTE
The “config.gcb” file can be renamed by the user and it will still be compatible with the G3X
system provided the .gcb file extension isn’t changed.
NOTE
If restoring data to the system from a backup, all previously saved data (including
calibration data) will be loaded. If saved configuration data is loaded into a different G3X
Touch system, the aircraft specific calibration data will not be overwritten.
To import the configuration:

1. Insert in the display slot an SD card with the “config.gcb” configuration file placed in a folder
named "config" within the "Garmin" folder on the SD card.
2. In configuration mode, navigate to the “Config Files” page.

Page A-5
3. Use the Touch Panel or a Move Selector Knob to select the “config.gcb” file.
4. Message similar to one below will appear. Select “Yes” when prompted.
5. When configuration download is complete, a check mark will appear in box next to the
“config.gcb” file.

Page A-6
APPENDIX B EXTERNAL INTERFACE CONFIGURATION
B.1 GPS/VHF Nav Interfaces

The GPS position sources listed in Table B-1 are compatible with the G3X Touch. Reference Section
3.2.2 for entering configuration and changing data on G3X units.
NOTE
Make configuration changes only as described in this section, changing other configuration
settings is not recommended and may significantly alter the unit’s operation. Garmin
recommends recording all existing configuration settings (before making any changes) for
reference.
Table B-1 – Compatible Equipment – GPS/VHF Nav Interfaces
MFR Model Data G3X Configuration Setting Interfacing Equipment
Format Configuration Setting
Garmin GNS 4XX(W)/ ARINC ARINC 429 Configuration GNS 4XX(W)/5XX(W)
5XX(W) Series 429 Page: Main ARINC Config Page:
429 Output 1: “EFIS /Airdata IN 1 Speed: “LOW”
Main Software v3.30 Format 1” and “Nav 1” IN 1 Data: “EFIS/Air Data”
or later is required. 429 Input 1: “Garmin GPS” OUT Speed: “LOW”
and “Nav 1” OUT Data: “GAMA 429”
429 Input 2: “Garmin SDI: “LNAV 1”
VOR/ILS” and “Nav 1” (GNS VNAV: “Enable Labels” (WAAS
430(W)/530(W)) Units Only)
For dual GNS configure #1 When interfaced with Non-
GNS as above and #2 GNS Garmin autopilot:
as below:
IN 2 Speed: “LOW” (2)
429 Output 2: “EFIS /Airdata IN 2 Data: “Garmin GAD 42” (2)
Format 1” and “Nav 2”
429 Input 3: “Garmin GPS”
and “Nav 2” for GNS #2 (If For dual GNS configure as above
Applicable) and below:
429 Input 4: “Garmin SDI: “LNAV 2” on #2 GNS (dual
VOR/ILS” and “Nav 2” for GNS ONLY)
GNS #2 (GNS VNAV: “Enable Labels” on #2
430(W)/530(W)) GNS (WAAS Units Only)

Page B-1
RS-232 RS-232 Configuration Page RS-232 Configuration Page
Serial Port ‘x’: “MapMX” CHNL 1 Input: “OFF”
(WAAS Unit) or “Aviation In” CHNL 1 Output: “MapMX”
(Non-WAAS unit) (WAAS units only) or “Aviation”
Serial Port ‘x’ (Connext (Non-WAAS unit)
bus): “Garmin Instrument CHNL 2 Input/Output: “Connext”
Data” (GNS 4XXW/5XXW (When Connext is used)
Only)
For dual GNS, configure #1

GNS as above and #2 GNS
as below:
RS-232 Configuration Page
Serial Port ‘x’: “MapMX”
(WAAS Unit) or “Aviation In”
(Non-WAAS unit) (PFD or
MFD)
NOTE: “x” = Connected Port

#
(GNS #1 must be connected
to a lower number port than
GNS #2. In dual GDU
installations GNS, #2 may be
connected to any port on the
MFD))
Misc. Main CDI/OBS Config Page
(GNS 430(W)/530(W)
Press Menu and select “Ignore
SEL CRS for VLOC” Option
Note: Menu will display “Allow
SEL Course for VLOC” when set
correctly.
VOR/ILS ARINC 429 Config

Mode Page (GNS
430(W)/530(W)
RX and TX Speed: “LOW”
SDI: “VOR/ILS 1” (“VOR/ILS 2”
for GNS 2)
GNS 480 ARINC ARINC 429 Configuration GNS 480 Main ARINC Setup
429 Page: Page:
Software v2.3 or later 429 Output 1: “EFIS /Airdata IN 2SEL: “EFIS”
is required. Format 1” and “Nav 1” IN 2 Speed: “LOW”
429 Input 1: “Garmin GPS” IN 2 SDI: “SYS1”
and “Nav 1” OUT 1SEL: “GAMA 429”
429 Input 2: “Garmin OUT 1 Speed: “LOW”
VOR/ILS” and “Nav 1” OUT 1 SDI: “SYS1”
OUT 2 SEL: “VOR/ILS”
OUT 2 Speed: “LOW”
OUT 2 SDI: “SYS1”
RS-232 RS-232 Configuration Page GNS 480 Serial Setup Page
Serial Port ‘x’: “MapMX” CHNL 1 Output: “MapMX

Page B-2
#
Misc. Resolver Interface Page
Resolver: “Not Installed”
Miscellaneous Setup Page
CDI Select: “USE”
GTN 6XX/ 7XX ARINC ARINC 429 Configuration GTN Main ARINC 429 Config
Software v6.71 or 429 Page: Page:
later is required 429 Output 1: “EFIS /Airdata IN 1 Speed: “LOW”
Format 1” and “Nav 1” IN 1 Data: “GDU Format 2”
429 Input 1: “Garmin GPS” OUT 1 Speed: “LOW”
GTN 6XX/ 7XX Xi and “Nav 1” OUT 1 Data: “Garmin 429”
Software v20.23 or 429 Input 2: “Garmin SDI: “LNAV 1”
later is required VOR/ILS” and “Nav 1” When interfaced with Non-
For dual GTN configure as Garmin autopilot:
above (GTN 1) and below IN 2 Speed: “LOW” (2)
(GTN 2): IN 2 Data: “GAD Format 1” (2)
429 Output 2: “EFIS /Airdata For dual GTN configure as above
Format 1” and “Nav 2” and below (GTN 2) :
429 Input 3: “Garmin GPS”
and “Nav 2” for GTN #2 (If IN 1 Speed: “LOW”
Applicable) IN 1 Data: “GDU Format 2”
429 Input 4: “Garmin OUT 1 Speed: “LOW”
VOR/ILS” and “Nav 2” for OUT 1 Data: “Garmin 429”
GTN #2 SDI: “LNAV 2” on #2 GTN (dual
GTN ONLY)
RS-232 RS-232 Configuration Page GTN RS-232 Configuration
Serial Port ‘x’: “MapMX” Page: On Both GTNs
(PFD) CHNL x Input: “MapMX Format
Serial Port ‘x’: “GTN 2”
Connext 2” (PFD) CHNL x Output: “MapMX
Format 2”
CHNL x Input/Output: “Connext
For dual GTN configure as Format 2” (When Connext is
above (GTN 1) and below used, #1 GTN Only)
(GTN 2): (1)
Serial Port ‘x’: “MapMX”
(PFD or MFD) for GTN 2 NOTE: “x” = Connected Port

# (GTN 1 must be connected
to a lower number port than
GTN 2. In dual GDU
installations GTN, #2 may be
connected to any port on the
MFD)
Misc. Main Indicator (Analog) Config
Page:
Selected Course for VLOC:
“Ignored”
VOR/LOC/GS Config Page:
Nav Radio: “Enabled”

Page B-3
ARINC 429 Config:
TX Speed: “LOW”
SDI: “VOR/ILS 1” (“VOR/ILS 2”
for GTN 2)
Notes:
(1) In installations with dual GTNs, GTN 1 must be connected to a lower number RS-232 port than
GTN 2. In dual GDU installations GTN, #2 may be connected to any port on the MFD)
(2) Only used when a Non-Garmin autopilot is interfaced, reference applicable interconnect diagrams
in the G3X Touch EFIS AML STC Installation Manual (190-02472-01).

Page B-4
B.2 GPS NAV Interface
The GPS Nav position source listed in Table B-2 is compatible with the G3X Touch. Reference Section
3.2.2 for entering configuration and changing data on G3X units
Table B-2 – Compatible Equipment – GPS NAV
Garmin GNC ARINC ARINC 429 Configuration Page: GNC 300XL/GPS 155XL ARINC
300XL/GPS 429 429 Output 1: “EFIS /Airdata 429 Config Page:
155XL Format 1” and “Nav 1” IN: “Course Heading”
429 Input 1: “Garmin GPS” and OUT: “King EFS 40/50”
“Nav 1”
RS-232 RS-232 Configuration Page: GNC 300XL/GPS 155XL I/O

Serial Port ‘x’: “Aviation In” CHANNEL 1 Config Page:
IN: “OFF”
NOTE: “x” = Connected Port # OUT: “Aviation”
GPS 175 ARINC ARINC 429 Configuration Page: GPS 175 ARINC 429 Config
429 429 Output 1: “EFIS /Airdata Page:
Format 1” and “Nav 1” IN 1: “GDU Format 2”, Low
429 Input 1: “Garmin GPS” and Speed
“Nav 1” OUT 1: “GAMA FORMAT 1”,
Low Speed
SDI: “LNAV 1”
RS-232 RS-232 Configuration Page: GPS 175 RS-232 CHNL 1
Serial Port ‘x’: “MAPMX” Config Page:
Serial Port ‘x’ (Connext): IN & OUT: “MAPMX FORMAT
“CONNEXT 57600 BAUD” 1”
GPS 175 RS-232 CHNL 2
Config Page:
NOTE: “x” = Connected Port #
IN & OUT: “CONNEXT 57600”
Misc. GPS 175 Main Indicator
(Analog) Page:
Selected Course: “Allowed”
GNC 355(A) ARINC ARINC 429 Configuration Page: GNC 355 ARINC 429 Config
Format 1” and “Nav 1” IN 1: “GDU Format 2”, Low
Low Speed
SDI: “LNAV 1”
RS-232 RS-232 Configuration Page: GNC 355 RS-232 CHNL 1
Serial Port ‘x’: “MAPMX” Config Page:
Serial Port ‘x’ (Connext): IN & OUT: “MAPMX FORMAT
“CONNEXT 57600 BAUD” 2”
GNC 355 RS-232 CHNL 2
Config Page:
IN & OUT: “CONNEXT 57600”
Misc. GNC 355 Main Indicator
(Analog) Page:
Selected Course: “Allowed”

Page B-5
GNX 375 ARINC ARINC 429 Configuration Page: GNX 375 ARINC 429 Config
Format 1” and “Nav 1” IN 1: “EFIS/AIR DATA”, Low
Low Speed
SDI: “LNAV 1”
RS-232 RS-232 Configuration Page: GNX 375 RS-232 CHNL 1
Serial Port ‘x’: “MAPMX” Config Page (Connected to
GDU):
Serial Port ‘x’ (Connext):
“CONNEXT 57600 BAUD” (2) IN & OUT: “MAPMX FORMAT
1”
GNX 375 RS-232 CHNL ‘x’
NOTE: “x” = Connected Port # Config Page (Connected to
GDU for Connext & ADS-B):
NOTE: No GSU configuration is IN & OUT: “CONNEXT 57600”
required GNX 375 RS-232 CHNL ‘x’
Config Page (Connected to
GSU 25D):
IN & OUT: “TRANSPONDER
FRMT 1”
Misc. Transponder Configuration GNX 375 Main Indicator
Page: (Analog) Page:
Transponder Type: “GNX 375” Selected Course: “Allowed”
(1)
On-screen Controls: “Show” (if
desired) or “Hide”
Notes:
(1) Set type on transponder configuration page of the GDU in configuration mode if remote control of
Transponder on G3X GDU is desired.
(2) Only one ADS-B Source maybe configured at a time.

Page B-6
B.3 VHF NAV/COM Interface
The navigation receivers listed in Table B-3 are compatible with the G3X Touch system. These receivers
transmit data to the G3X Touch system digitally.
Table B-3 – Compatible Equipment – VHF NAV/COM
Garmin GNC 255 RS-232 RS-232 Configuration Page: Nav Configuration Page:
One or two Serial Port ‘x’: “Garmin VHF CDI Indicator Type: “Serial”
navigation Nav/Comm” SYS Configuration Page:
receivers can NOTE: “x” = Connected Port #
be connected Serial Port IO Mode: “NMEA”
GNC software
v2.21 or later is
required to
support remote
Nav tuning from
G3X.
SL 30 RS-232 RS-232 Configuration Page: Nav Setup Pages:
Serial Port ‘x’: “Garmin VHF Attitude Config Page:
Nav/Comm” Indicator Head Type: “Serial”
SL 40 RS-232 RS-232 Configuration Page: N/A
Serial Port ‘x’: “Garmin VHF
Comm”
GTR 225 RS-232 RS-232 Configuration Page: SYS Configuration Page:
Serial Port ‘x’: “Garmin VHF Serial Port IO Mode: “NMEA”
Comm”
GTR 20 CAN Reference G3X Touch EFIS None
Part 23 AML STC Installation
Manual for configuration
information
GTR 200B CAN Reference G3X Touch EFIS Reference G3X Touch EFIS Part
Part 23 AML STC Installation 23 AML STC Installation Manual
Manual for configuration for configuration information
information

Page B-7
B.4 Traffic and Weather Source
Table B-4 – Compatible Traffic and Weather Sources
Garmin GTX 33(ES) RS-232 Transponder Configuration Page: GTX 330(ES)/327/328 RS-232 Config
GTX 330(ES) Transponder Type: “GTX 32” or “GTX Mode Page:
GTX 32 33” or “GTX 33ES” or “GTX 327” or “GTX RS-232 Input: “Remote”
328” or “GTX 330” or “GTX 330ES” as RS-232 Output: “Remote+TIS”
GTX 327 appropriate (1)
GTX 328 Note: No configuration is required for
GTX32/33(ES)
(3)
Note: No GSU configuration is required GTX 328/330 Squat Switch Config
Mode Page:
Squat Switch: “NO”
GTX 325 RS-232 Transponder Configuration Page: GTX 325/335(D) RS-232 Set Up
GTX 335(D) Transponder Type: “GTX 325” or “GTX Page:
GTX 335(D)R 335” or “GTX 335D” or “GTX 335R” or RS-232 CH 1 (Connected to GSU
“GTX 335DR” as appropriate (1) 25D: “XPDR FMT 1”
GTX 335(D)R Connected to Garmin For ADS-B

Navigator for Position Source for ADS- GTX 335(D) RS-232 CH (Connected
B Out to Garmin Navigator) Input: “ADS-
Transponder Configuration Page: B+”
RS-232 Port ‘x’: ‘ADS-B+ GPS”
(3) GTN/GNS RS-232 Configuration
NOTE: No GSU configuration is required Page:
NOTE: “x” = Connected Port # RS-232 CH (Connected to GTX)
Output: “ADS-B+ Format 1”
GTX 345(D) RS-232 Transponder Configuration Page: GTX RS-232 Set Up Page:
Transponder Type: “GTX 345” or “GTX RS-232 CH 1 (Connected to GSU
GTX software 345D” as appropriate (1) 25D)
v2.60 or later On-screen Controls: “Show” (if desired) Input/Output Format: “XPDR FMT 1”
is required. or “Hide” RS-232 CH ‘x’ (Connected to GDU):
RS-232 Configuration Page: Input/output: “Connext FMT 4”
RS-232 Port ‘x’: ‘Connext 115200 Baud”
(GDU port connected to GTX) (2) For ADS-B
- For Traffic/Weather (if no other source GTX RS-232 CH (Connected to
is connected) Garmin Navigator) Input: “ADS-B+”
The GTX 345(D) also provides FIS-B GNS RS-232 Configuration Page:
weather data with this interface.
RS-232 CH (Connected to GTX)
NOTE: No GSU configuration is required NOTE: “x” = Connected Port #

Page B-8
GTX 345(D)R RS-232 Transponder Configuration Page: GTX Installed with GTN
HSDB (w/ Transponder Type: “GTX 345R” or GTN Interfaced Equipment Page:
GTX software GTN or GTS) “GTX 345DR” as appropriate (1) ADS-B IN Source Type: “GTX #1”
v2.60 or later
is required. RS-232 Port ‘x’: ‘Connext FMT 4” (GTX GNS RS-232 Configuration Page:
port connected to GDU)
RS-232 CH (Connected to GTX)
RS-232 Configuration Page:
(GDU port connected to GTX) (2)
For Traffic/Weather (if no other source is
connected)
ADS-B/TIS-B
GTX 345(D)R Connected to Garmin
Navigator for Position Source for ADS-
B Out (2)
Transponder Configuration Page:
HSDB Devices: Enable “GTN” or “GTS”
NOTE: No GSU configuration is required

GTX 345(D)R RS-232 Transponder Configuration Page: GTN Interfaced Equipment Page:
w/ Non- HSDB (w/ Transponder Type: “None” ADS-B IN Source Type: “GTX #1”
Garmin GTN)
Traffic
RS-232 Configuration Page: GTX Install Tool Configuration: (5)
RS-232 Port ‘x’: ‘Connext 115200 Baud” RS-232 CH 1 (Connected to GSU
(GDU port connected to GTX) (2) 25D) Input/Output Format:
“Transponder R FMT 1”
RS-232 CH ‘x’ (Connected to GDU):
Input/output: “Connext FMT 4”

GDL 5XR RS-232 RS-232 Configuration Page: N/A
(GDU port connected to GDL) (2)

GTS 8XX RS-232 RS-232 Configuration Page: GTS 8XX Traffic Display Destination
ARINC 429 (if RS-232 Port ‘x’: GTS Instrument Data Page:
Software connected to Enhanced COM Port: “RS-232 Port
V4.10 and GTX) x”
If a remote GTX that supports TIS-A is
later for GTS installed disable as shown below: (GTS port connected to GDU)
8X0, v3.10
and later for Transponder Configuration Page:
GTS 8X5 TIS-A Traffic Data: “Disable” GTS 8XX Configuration Page:
ADS-B Receiver: “On”
Allow ADS-B in Standby: Enabled
If GTX 335(D)(R) is installed:

Page B-9
GTS 8XX Transponder 1
Communication Page:
A429 Primary TX/RX: set to “TX/RX
Channel x and Check HIGH SPEED”
(GTS port connected to GTX)
GTS 8XX GPS Position Velocity
Page, Barometric Altitude Source,
and Magnetic Heading Source:
A429 Primary RX: set to “RX Channel
x and Check HIGH Speed” (GTS port
connected to GTX)
Notes:
(1) Set type on transponder configuration page of the GDU in configuration mode if remote control of
Transponder on G3X GDU is desired. If the transponder will be controlled by another device
such as a GTN, set Transponder Type to None on the G3X configuration page.
(2) Only one ADS-B Source maybe configured at a time.
(3) If a GDL 50R/52R is installed with a GTX 33ES or GTX 335(D)R, ensure UAT and 1090ES are
enabled (green indicator). Reference the G3X Touch EFIS Part 23 AML STC Installation Manual
(190-02472-01) for detailed configuration information.
(4) See Table B.2 for GNX 375 configuration information.
(5) To configure GTX 345(D)R with a non-Garmin traffic system, the GTX 3X5 Installation Tool must
be used. Reference the GTX 3X5 TSO Installation Manual 190-01499-02 for guidance. GTX
345(D)R configuration module must be installed.

Page B-10
B.5 Non-Garmin Autopilot Systems
Non-Garmin autopilots listed in Table B-5 are compatible with the G3X Touch system.
Table B-5 – Compatible Equipment – Non-Garmin Autopilots
Format Configuration Information
Century 1C388* analog Analog Autopilot Configuration
Page:
Autopilot Type: “Century 1C388”
GPS Steering: “Enabled”
GPSS Scale Factor: “1.000”
1C388M* analog Analog Autopilot Configuration
Page:
Autopilot Type: “Century 1C388M”
1C388C* analog Analog Autopilot Configuration
Page:
Autopilot Type: “Century 1C388C”
1C388MC* analog Analog Autopilot Configuration
Page:
Autopilot Type: “Century
1C388MC”
1C388-2* analog Analog Autopilot Configuration
Page:
Autopilot Type: “Century 1C388-2”
1C388-3* analog Analog Autopilot Configuration
Page:
Autopilot Type: “Century 1C388-3”
2000 analog Analog Autopilot Configuration
Page:
Autopilot Type: “Century 2000”
Page:
Page:

Page B-11
Page:
IV analog Analog Autopilot Configuration
Page:
Autopilot Type: “Century IV”
Cessna 300 IFCS analog Analog Autopilot Configuration
400 IFCS Page:
800 IFCS Autopilot Type: “Cessna 300 (AC)”,
“Cessna 400 (AC)” or “Cessna 800
(AC)” – as applicable.
300B IFCS analog Analog Autopilot Configuration
400B IFCS Page:
800B IFCS Autopilot Type: “Cessna 300 (DC)”,
“Cessna 400 (DC)” or “Cessna 800
(DC)” – as applicable.
Honeywell / KAP 100 analog Analog Autopilot Configuration
Bendix Page:
King Autopilot Type: “Bendix King KAP
100” GPS Steering:
“Enabled” GPSS Scale
Factor: “1.000”
KAP 140 analog Analog Autopilot Configuration
Page:
Autopilot Type: “Bendix King KAP
Factor: “1.000”
Page:
Factor: “1.000”
Page:
Factor: “1.000”
KFC 150 analog Analog Autopilot Configuration
Page:
Autopilot Type: “Bendix King KFC

Page B-12
Factor: “1.000”
KFC 200 analog Analog Autopilot Configuration
Page:
Autopilot Type: “Bendix King KFC
Factor: “1.000”
KFC 225 analog, Analog Autopilot Configuration
ARINC 429 Page:
GPSS Autopilot Type: “Bendix King KFC
225”
S-TEC System 20 analog, Analog Autopilot Configuration Must be configured to operate
discrete Page: with KI-525 (KCS-55) heading
Autopilot Type: “S-Tec System 20” system.
System 30 analog, Analog Autopilot Configuration Must be configured to operate
System analog, Analog Autopilot Configuration Must be configured to operate
55X discrete, Page: with KI-525 (KCS-55) heading
ARINC 429 Autopilot Type: “S-Tec System system.
55X”

system.
Autopilot Type: “S-Tec System 60”
System 65 Analog Analog Autopilot Configuration Must be configured to operate

system.

Page B-13
Autopilot Type: “S-Tec System 65”
Piper Autocontrol analog Analog Autopilot Configuration Page:

III/IIIB/IIIC Autopilot Type: “Piper AutoControl”
Altimatic analog Analog Autopilot Configuration Page:

III/IIIB-1/IIIC Autopilot Type: “Piper Altimatic”
B.6 Audio Panel

The following audio panels interface with the G3X Touch system. For all other audio panels, refer to
installation guidance for the selected audio panel for configuration information.
Table B-6 – Compatible Equipment – Audio Panel
MFR Model Data G3X Configuration Interfacing Equipment
Format Setting Configuration Setting
Garmin GMA 342/345 RS-232 RS-232 Configuration Page: Refer to the GMA 342/345 Installation
Serial Port ‘x’: “Garmin Instrument Manual for guidance.
Data”
Sound Configuration Page:
Alert Source: “PFD”
Alert Output: “Mono Only”
GMA 245R CAN Sound Configuration Page: None
Alert Source: “PFD”
Alert Output: “Mono Only”
NOTE: Reference Section 5 for

additional configuration information

Page B-14
B.7 EIS Sensors
G3X EIS gauge displays require data captured by approved sensors that are configured in accordance
with Table B-7. EIS Sensors that are authorized as Interface Only require a separate installation
approval.
Table B-7 – Compatible EIS Sensors
Function Mfg. Garmin P/N Description G3X Sensor Input STC Approval
Configuration
Cylinder Alcor 494-70008-00 Alcor 86252 (K type CHT → Type K Interface Only
Head probe)
Temperature Varies N/A K Type Thermocouple CHT → Type K Interface Only
Varies N/A J Type Thermocouple CHT → Type J Interface Only
Exhaust Gas Alcor 494-70001-00 Alcor 86255 (Type K EGT → Type K Interface Only
Temperature Thermocouple,
Clamp)
Varies N/A K Type Thermocouple EGT → Type K Interface Only
Turbo Inlet Alcor 494-70002-00 Alcor 86245 (Type K Misc. Temp 1 or 2 Interface Only
Temperature probe) →Turbine Inlet Temp 1
or 2 (Type K
Thermocouple)
Varies N/A K Type Thermocouple Misc. Temp 1 or 2 Interface Only
→Turbine Inlet Temp 1
or 2 (Type K
Thermocouple)
Garmin 011-04202-30 150 PSIG Brass Oil Pressure → Kavlico Interface &
P4055-5020-4 Installation
Garmin 011-05783-30 GPT 150PSIG Oil Pressure → Garmin Interface &
Oil Pressure Stainless Steel GPT 150G Installation
Textron N/A Beech 102-389017-1 Oil Pressure → Beech Interface Only
Aviation 102-389017
Textron N/A Beech 102-389017-3 Oil Pressure → Beech Interface Only
Aviation 102-389017
UMA N/A T1EU150G Oil Pressure → UMA Interface Only
T1EU150G
UMA N/A T1EU150G-CS Oil Pressure → UMA Interface Only
T1EU150G
UMA 494-70009-00 T3B3-2.5G (K Type Oil Temp → Type K Interface &
probe) Installation
UMA N/A T3B3 Oil Temp → Type K Interface Only
Oil Temp UMA N/A T3B3A Oil Temp → Type K Interface Only
UMA N/A T3B3-2.5 Oil Temp → Type K Interface Only
Mil-Spec N/A MS28034 Oil Temp → MS28034 Interface Only
Varies N/A K Type Thermocouple Oil Temp → Type K Interface Only
Garmin 011-04202-00 30 PSIA Brass Manifold Pressure → Interface &
Manifold Kavlico P4055-5020-1 Installation
Pressure Garmin 011-05783-00 GPT 30PSIA Manifold Pressure → Interface &
Stainless Steel Garmin GPT 30A Installation
UMA N/A T1EU50A Manifold Pressure → Interface Only
UMA T1EU50A
UMA N/A T1EU50A-CS Manifold Pressure → Interface Only
UMA T1EU50A
UMA 494-70010-00 T3B10-SG (K Type Misc. Temp 1 or 2 Interface &
probe) →Carb Temp (Type K Installation
Carb Air Thermocouple)
Temp Mil-Spec N/A MS28034 Misc. Temp 1 or 2 → Interface Only
Carb Temp (MS28034)

Page B-15
Configuration
Varies N/A K Type Thermocouple Misc. Temp 1 or 2 Interface Only
(various →Carb Temp (Type K
manufacturers) Thermocouple)
Garmin 011-04202-20 75 PSIG Brass Fuel Pressure → Interface &
Kavlico P4055-5020-3 Installation
(0-75 PSI)
Garmin 011-05783-20 GPT 75PSIG Fuel Pressure → Interface &
Fuel Press Stainless Steel Garmin GPT 75G (0-75 Installation
PSI)
Garmin 011-04202-10 15 PSIG Brass Fuel Pressure → Interface &
Kavlico P4055-5020-2 Installation
(0-15 PSI)
Garmin 011-05783-10 GPT 15PSIG Fuel Pressure → Interface &
Stainless Steel Garmin GPT 15G (0-15 Installation
PSI)
UMA N/A T1EU70G Fuel Pressure → UMA Interface Only
T1EU70G (0-70 PSI)
UMA N/A T1EU70G-CS Fuel Pressure → UMA Interface Only
T1EU70G (0-70 PSI)
UMA N/A T1EU35G Fuel Pressure → UMA Interface Only
T1EU35G (0-35 PSI)
UMA N/A T1EU35G-CS Fuel Pressure → UMA Interface Only
T1EU35G (0-35 PSI)
Shunt Varies N/A AA55524 (various Shunt 1 or 2 (manual Interface Only
mfgr) configuration)
Lamar N/A CS3200 Shunt 1 or 2 (manual Interface Only
configuration)
Voltage Varies N/A N/A (sense Bus Volts 1 or 2 (manual Interface Only
Voltage) configuration)
Resistive N/A 25-620Ω Resistive Fuel 1 or 2 or 3 or 4 → Interface Only
Fuel float* float interfaced with Voltage*
Quantity dual 2.2k Ω resistors
to GEA 24 or 24B
Resistive N/A 25-620Ω Resistive Fuel 1 or 2 or 3 or 4 → Interface Only
float* float with direct Resistive*
interface to GEA 24B
Only
CIES N/A CiES CC284022- Fuel 1 or 2 or 3 or 4 → Interface Only
CORP XXXX-105 (0-5V Voltage
Analog)
CIES N/A CiES CC284022- Fuel 1 or 2 or 3 or 4 → Interface Only
CORP XXXX-101 (Digital) Digital
Electroni 494-10001-00 EI FT-60 (Red Cube) Fuel Flow → EI FT-60 Interface &
Fuel Flow & cs Installation
Return FF Internatio
nal
Electroni 494-10001-01 EI FT-90 (Gold Cube) Fuel Flow → EI FT-90 Interface &
cs Installation
Internatio
nal
Textron N/A 102-389012-11 Fuel Flow → Beech Interface Only
Aviation 102-389012
JPI N/A JPI 700900-1 (201) Fuel Flow → Floscan Interface Only
201 B6
JPI N/A JPI 700900-2 (231) Fuel Flow → Floscan Interface Only
231

Page B-16
Configuration
Floscan N/A Floscan 201 B-6 Fuel Flow → Floscan Interface Only
201 B6
Floscan N/A Floscan 231 Fuel Flow → Floscan Interface Only
231
Shadin N/A Shadin 680501(XX.X) Fuel Flow → Floscan Interface Only
Shadin 680501- 201 B6
1(XX.X)
UMA N/A UMA T1A9-1 (Slick RPM 1 → UMA T1A9 Interface Only
RPM Mag) Mag Port (4 or 6-
Cylinder)
UMA N/A UMA T1A9-2 (Bendix RPM 1 → UMA T1A9 Interface Only
Mag) Mag Port (4 or 6-
Cylinder)
N/A Magneto P-lead, 4- RPM → Magneto P- N/A (No sensor
Cylinder Lead (1.000 pulse/rev) req’d)
Cylinder Lead (1.500 pulse/rev) req’d)
Cylinder, 0.64000:1 Lead (2.344 pulse/rev) req’d)
Prop Gear Ratio
Prop Gear Ratio
Prop Gear Ratio
Prop Gear Ratio
Prop Gear Ratio
N/A Dual Magneto P-lead, RPM → Magneto P- N/A (No sensor
4-Cylinder Lead (2.000 pulse/rev) req’d)
N/A Dual Magneto P-lead, RPM → Magneto P- N/A (No sensor
6-Cylinder Lead (1.500 pulse/rev) req’d)
SureFly N/A TACH2 0-5V, 4- RPM → Magneto P- Interface Only
Cylinder Lead (1.000 pulse/rev)
Cylinder Lead (1.500 pulse/rev)
Cylinder, 0.64000:1 Lead (2.344 pulse/rev)
Prop Gear Ratio
Prop Gear Ratio
Prop Gear Ratio
Prop Gear Ratio
Prop Gear Ratio

Page B-17
* Configure ‘Voltage’ when the GEA 24 or GEA 24B is wired with dual 2.2kΩ resistors (ref. G3X Touch
EFIS Installation Manual for wiring information). Configure ‘Resistive’ when the GEA 24B is wired without
any in-line resistors. Do not configure ‘Resistive’ for the GEA 24, it must use the 2.2kΩ resistors and
‘Voltage’ configuration. .

Page B-18
B.8 Antennas
This section contains general information for interfaced GPS, GPS/WAAS, SXM, ADS-B, COM, and
Marker Beacon antennas. This STC provides installation approval only for the Garmin glareshield-
mounted GPS Antenna (011-04036-10 and 011-04036-00), refer to the G3X Touch EFIS Part 23 AML
STC Installation Manual (190-02472-01) for installation guidance. All other antennas are approved as
interface only and require separate installation approval.
A minimum of one GPS antenna is required for G3X installations as the connected GDU (PFD) will share
GPS data with the second GDU (if installed). Additional GPS antennas may be used for redundancy but
are not required.
Table B-8 – Supported GPS & SXM Antennas
Approved LRU
Make & Model P/N Mounting
G3X Function Connection
Comant 2480-201 CI 2480-201 GPS GDU 4X0 Blade antenna, external
(GPS/VHF Com)
Garmin Glareshield GPS 011-04036-00 GPS GDU 4X0 Glareshield mounted via hook &
Antenna (TNC) (ordered as 010- loop or screws
12444-00)
Garmin Glareshield GPS 011-04036-10 GPS GDU 4X0 Glareshield mounted via hook &
Antenna (BNC) (ordered as 010- loop or screws
12444-10)
Garmin GA 56 011-00134-00 GPS GDU 4X0 Stud mount, teardrop, external
part of Kit 010-
10040-01
Garmin GA 37 013-00245-00 SXM GDL 51R/52R ARINC 743, external
(GPS/SXM)
Garmin GA 55 011-01033-00 SXM GDL 51R/52R Stud-mount, teardrop, external
Garmin GA 55A 011-01153-00 SXM GDL 51R/52R Through-mount, ARINC 743,
external
The GPS antenna interface on the GDL 5XR is not used in this STC.
Only the SXM connection to the GA 37 antenna is approved in this STC. The GPS connection to the GA
37 is not compatible with any G3X LRUs but might be used for other installed equipment under their
respective interface approvals.
Also note that if a previously installed G5 is connected to a GPS antenna mounted externally on the
airframe, that antenna must be disconnected when the G5 is used as a standby instrument for G3X. It
may be possible to repurpose the external antenna for other avionics if it is compatible under their
respective interface approvals.
The GPS antenna should provide a gain of 16 to 25 dB. The GDU 4X0 supplies power to the antenna at
4.5-5.5 VDC with a maximum current of 50 mA.
The following information describes antenna performance requirements for proper system functionality.

Page B-19
Table B-9 – GPS or GPS/WAAS Antenna Minimum Requirements
Characteristics Specifications
Frequency Range 1565 to 1585 MHz
Gain 16 to 25 dB typical, 40 dB max.
Noise Figure <4.00 dB
Nominal Output Impedance 50Ω
Supply Voltage 4.5 to 5.5 VDC
Supply Current up to 50 mA
Output Connector BNC or TNC
Table B-10 – SXM Satellite Radio Antenna Minimum Requirements

Characteristics Specifications
Frequency Range 2332.5 to 2345 MHz
Gain 24 dB*
Noise Figure <1.2 dB
Nominal Output Impedance 50Ω
Supply Voltage 3.5 to 5.5 VDC
Supply Current 55 mA
Operating Temperature Gain -50° to +85° C
* - For each 1 dB gain over 24 dB, add 1 dB of attenuation into the antenna cable path between the
antenna and the GDU.
B.9 ADS-B Antenna Interface
The GDL 50R or GDL 52R requires an external monopole or blade-type ADS-B antenna for reception.
The antenna should be mounted on the bottom of the aircraft and located at least 3.3 feet from high
power transmitting antennas such as VHF Comm, HF transmitter, DME, Transponder, and Radar. The
connection is made by attaching the coax cable from the external antenna to the BNC connector on the
GDL 50R/52R. The GDL 50R/52R requires a UHF antenna that meets the following specifications:
• Standard 50 Ω vertically polarized antenna with a VSWR < 1.7:1 at 978 MHz and < 1.5:1 at 1090
MHz.
• TSO-C66, TSO-C74, or TSO-C112 antennas that also meet the VSWR specification.
B.10 COM Antenna Interface
The GTR 20/200B requires an external COM antenna for reception. The COM antenna should be
electrically bonded to a flat ground plane over as large an area as possible (at least 18 inches square).
The antenna should be located at least 6 feet from other COM antennas, four feet from any ADF sense
antennas, two feet from any GPS/SBAS antenna, and as far apart as practical from the ELT antenna for
best performance. A configuration of one top-side antenna and one bottom-side antenna is recommended
for dual COM installations. The GTR 20/200B requires a VHF antenna that meets the following
specifications:
• Standard 50 Ω vertically polarized antenna.
• TSO-C37() and C38() or TSO-C169().

Page B-20
B.11 Marker Beacon Antenna Interface
The GMA 245R may optionally be connected to an external marker beacon antenna for reception. The
antenna must meet TSO-C35(). The marker beacon antenna should be mounted on a flat surface on the
underside of the aircraft body.
The antenna should be located to minimize the amount of structure between it and the ground radio
stations. It should be located as far away as possible from transmitter antennas.
In a composite aircraft, the antenna must have an acceptable ground plane. Conductive wire mesh,
radials, or thin aluminum sheets embedded in the composite material provide the proper ground plane.

Page B-21

Garmin G3X Touch MM

Uploaded by

Copyright:

Available Formats

Garmin G3X Touch MM

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Garmin G3X Touch MM

Uploaded by

Copyright:

Available Formats

Garmin G3X Touch

Electronic Flight Instrument System

190-02472-02 October 2023 Revision 9

Garmin (Europe) Ltd.

Garmin Würzburg GmbH

Garmin AT, Inc.

Maintenance Manual 190-02472-02

INFORMATION SUBJECT TO EXPORT CONTROL LAWS

Maintenance Manual 190-02472-02

Maintenance Manual 190-02472-02

Maintenance Manual 190-02472-02

Maintenance Manual 190-02472-02

Maintenance Manual 190-02472-02

Maintenance Manual 190-02472-02

Maintenance Manual 190-02472-02

Maintenance Manual 190-02472-02

Maintenance Manual 190-02472-02

1.1 Content, Scope, Purpose

Maintenance Manual 190-02472-02

Section 7: G3X Equipment Configuration & Testing

Section 8: System Return to Service Procedure

Appendix A: Installation Specific Information

Maintenance Manual 190-02472-02

Maintenance Manual 190-02472-02

Maintenance Manual 190-02472-02

190-02472-00 Garmin G3X Pilot’s Guide for Certified Aircraft

1.5 Revision and Distribution

Maintenance Manual 190-02472-02

Maintenance Manual 190-02472-02

Maintenance Manual 190-02472-02

Maintenance Manual 190-02472-02

2.1.2 GDU 470

Maintenance Manual 190-02472-02

Figure 2-2 – GDU 470 (PFD)

Maintenance Manual 190-02472-02

Figure 2-3 – GSU 25D ADAHRS

2.1.4 GMU 11 Magnetometer

Figure 2-4 – GMU 11 Magnetometer

2.1.5 GTP 59 Temperature Probe

Maintenance Manual 190-02472-02

2.1.6 GAD 29B/29D ARINC 429 Adapter (Optional)

Figure 2-6 – GAD 29B/29D (ARINC 429 Adapter)

2.1.7 GAD 27 Electronic Adapter Unit

Maintenance Manual 190-02472-02

2.1.8 GEA 24(B) Engine/Airframe Unit

Figure 2-8 – GEA 24(B) Engine and Airframe Unit

2.1.8.1 EIS Functionality

Maintenance Manual 190-02472-02

2.1.9 GDL 5XR Data Link

Maintenance Manual 190-02472-02

Figure 2-10 – GPS Antenna (011-04036-10 Shown)

2.1.11 GAP 26 AOA Probe

Maintenance Manual 190-02472-02

2.1.12 GTR 20 VHF COM Radio

Figure 2-12 – GTR 20 COM Radio

2.1.13 GTR 200B VHF COM Radio

Maintenance Manual 190-02472-02

Figure 2-14 – GMA 245R Audio Panel

2.2 G3X Optional Interfaces

Maintenance Manual 190-02472-02